Grundig Flat Panel Television 8140 S User Manual

LCD TV

HAMBURG 32 VLC 8140 S

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents_{--------------------------------------------------------------------------------------------------------------------------------------}

49- operAtion-As-A-pC-monitor

49 Connecting a PC

49 Selecting presets for the PC

49 Settings for PC mode

50- operAtion-with-A-Common-

interFACe

50 What is a Common Interface?

50 Inserting the CA module

50 Access control for CI module and

smart card

51- speCiAl-settinGs

51 Searching for digital television channels

from a satellite automatically

52 Searching for digital television

channels from a satellite automatically

52 LNB settings

53 Settings for motorised antennas

(DiSEqC 1.2)

55 Searching for digital terrestrial

TV channels automatically

56 Searching for digital terrestrial

TV channels manually

56 Tuning analogue television channels

58 Changing stored analogue channels

60- inFormAtion

60 Displaying signal information

61 Technical data

62 Service information for retailers

62 Environmental note

63 Troubleshooting

-3

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

setup-AnD-sAFetY_{-------------------------------------------------------------------------------------------------------}

Please note the following instructions when

setting up the television set:

Make sure the power cord or the power sup-

ply unit (if provided) are not damaged.

This television is designed to receive and dis-

Only operate the television with the power

supply/power cord provided.

play video and audio signals.

All other uses are expressly prohibited.

Thunderstorms are a danger to all electrical

devices. Even when the television is switched

off, it can be damaged by a lightning strike to

the mains or the antenna. Always disconnect

the mains and antenna plugs during a storm.

The ideal viewing distance is five times the

diagonal screen size.

Light falling on the screen impairs picture

quality.

Use a damp, soft cloth to clean the screen.

Do not use water with soap or detergent.

To ensure the device is always adequately

ventilated, make sure there is sufficient space

between the television set and nearby furni-

ture.

Only clean the housing of your television set

with the cloth provided. Do not use water with

soap or detergent.

The television is designed for use in dry rooms.

If you do use it outdoors, make sure it is pro-

tected from moisture such as rain or splashing

water.

When deciding where to put the device, re-

member that furniture is often coated with

various types of varnish and plastic. Many of

these contain chemicals which can corrode

the feet of the device, leaving marks on the

surface of the furniture which can be difficult

or impossible to remove.

Never expose the television set to moisture.

Do not place any vessels such as vases on the

television, as they may spill liquid, thus present-

ing a safety risk.

The screen of your LCD television meets

the highest quality standards and has been

checked for pixel faults.

Despite the great care taken in manufacturing,

technological reasons make it impossible to

completely discount the possibility that some

pixels may be faulty.

Provided they are within the thresholds speci-

fied by the DIN norm, pixel faults of this kind

cannot be regarded as a defect as defined by

the warranty.

Place the television on a hard, level surface.

Do not place any objects such as newspapers

on the television or put cloth or similar items

under it.

Do not place the television close to heating

units or in direct sunlight, as this will impair

cooling.

Heat build-up can be dangerous and shortens

the service life of the television. For reasons of

safety, have a repairman remove any dirt in

the television from time to time.

To ensure fires do not occur,

always keep candles and other

open flames away from the device.

Never open the television under any circum-

stances. Warranty claims are excluded for

damage resulting from improper handling.

-4

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

setup-AnD-sAFetY_{-------------------------------------------------------------------------------------------------------}

Do not connect any other equipment while the

device is switched on. Also switch off other

equipment before connecting it.

Do not plug in the power cord of the device

until you have connected the external equip-

ment and the antenna.

Make sure the mains plug is freely accessible.

Caution:

If you plan on using a wall bracket for your

television, make sure you read the assembly

manual for the wall bracket or have a spe-

cialist assemble it.

When purchasing the wall bracket, make

sure that all the fastening points on the televi-

sion are also on the wall bracket and that

they are all used when mounting it.

-5

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

GenerAl-inFormAtion_{----------------------------------------------------------------------------------}

special-features-of-your-

-television-set

You can receive and watch digital TV channels

using your television set (via DVB-S, DVB-T and DVB-

C) – including High Definition programmes (HD).

However, the reception of digital TV channels in HD

is currently limited to a few countries in Europe.

Although this television set complies with the current

DVB-S, DVB-T and DVB-C standards (status: August

2010), the compatibility with future DVB-S satellite

transmissions as well as terrestrial DVB-T and DVB-C

cable programmes cannot be guaranteed.

Your television set can receive and process

all analogue and non-encrypted digital

TV channels. The television set is also equipped

with digital and analogue receivers.

The electronic TV guide (for digital channels

only) informs you about any schedule changes

at short notice, and provides an overview of

all the broadcasters' schedules for the next few

days. Detailed information on the individual

television programmes are – when provided

by the broadcasting station – are also avail-

able in the electronic TV guide.

You can connect various data media, such as

an external hard drive, a USB memory stick or

a digital camera, to the USB socket. Using the

file browser, you can then select and play the

file formats of your choice (for example, MP4,

MP3 or JPEG data).

Using the time shift function, you can quickly and

easily pause a programme using the remote

control and resume it at a later stage. The pro-

gramme is recorded in an external data medium.

You can record any digital TV channels you

choose.

The TV channels are converted by the televi-

sion and saved on an external data medium

which is connected to the USB socket.

The saved programmes can be called up and

played from the archive on the external data

medium at any time.

You can also play a programme from the

archive while recording another.

More information on recording and playing

TV programmes can be found on page 26.

-6

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

GenerAl-inFormAtion_{----------------------------------------------------------------------------------}

receiving-digital-channels

You require a satellite antenna to receive

digital satellite channels (DVB-S).

important-notes-on-

environmental-protection

The following information will help you to save

resources – and money as well.

You require a digital roof antenna or indoor

antenna (passive or active indoor antenna

with its own power supply) to receive digital

television channels (DVB-T).

If you are not using your television set for

several days, you should pull out the mains

plug for environmental and safety reasons.

This way the television does not consume any

electricity.

If you wish to receive digital television chan-

nels via your cable system (DVB-C), the an-

tenna cable for your cable operator must be

connected to the television set.

As switching off the television set does not

completely disconnect it from the mains, pull

out the plug to disconnect it from the mains

completely.

Unlike analogue broadcasting, not every

channel has its own transmission frequency.

Instead, several channels are grouped into

what are known as bouquets on a regional or

national level. You can find the current trans-

mission information on teletext from various

broadcasters, or by consulting a current TV

guide or the Internet.

If the device is equipped with a power switch,

switching it off using this switch will be suffi-

cient. The energy consumed by the television

set is reduced to virtually 0 W.

In standby mode, the television set uses very

low energy. However, it may be necessary

to leave the television set in standby mode

for certain functions (for example automatic

switch-on and switch-off and for timer func-

tions).

Various digital television channels from private

broadcasters are encrypted (DVB-S, DVB-T

and DVB-C). Watching these channels and

the recording and playback functions are only

possible with the appropriate CI module and

a SmartCard. Ask your specialist dealer.

The television set uses less energy when the

brightness is reduced.

The range of channels available from the pub-

lic broadcasting institutions (ARD with EinsEx-

tra, EinsFestival or ZDF with ZDF Info and all

third party broadcasters) are not encrypted

and can be received without a SmartCard.

-7

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConneCtion-AnD-prepArAtion_{------------------------------------------------}

Connecting-the-antenna-and-power-cord

To receive digital satellite channels (DVB-S),

connect the satellite antenna cable to the

antenna socket »sAtellite« on the televi-

sion set.

note:

When connecting an indoor antenna you

may have to try it out at different positions

until you get the best reception.

And/or:

Plug the power cord into a wall socket.

2a To receive terrestrial digital broadcasters

(DVB-T) connect the cable for the rooftop

or indoor antenna (passive or active indoor

antenna with its own power supply) to the an-

tenna socket »Ant-in« on the television set;

note:

Do not plug in the power cord of the device

until you have connected the external equip-

ment and the antenna.

Only use the power cord supplied to connect

the television set to a suitable earthed safety

socket.

2b To receive digital cable channels (DVB-C)

connect the cable for the rooftop antenna

to the antenna socket »Ant- in« on the

television set;

Do not use an adapter plug or extension

lead which does not meet the applicable

safety standards. Do not tamper with the

power cord.

2c To receive analogue TV channels, connect

the cable for the rooftop antenna to the an-

tenna socket »Ant-in« on the television set

-8

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConneCtion-AnD-prepArAtion_{------------------------------------------------}

environmental-note

inserting-batteries-into-the-

-remote-control

This symbol on recharge-

able batteries/batteries or

on the packaging indicates

that the rechargeable bat-

tery/battery may not be disposed of with

regular household rubbish. For certain

rechargeable batteries/batteries, this sym-

bol may be supplemented by a chemical

symbol. Symbols for mercury (Hg) or lead

(Pb) are provided if the rechargeable batter-

ies/batteries contain more than 0.0005%

mercury or more than 0.004% lead.

Rechargeable batteries/batteries, including

those which do not contain heavy metal,

may not be disposed of with household

waste. Always dispose of used batteries

in accordance with local environmental

regulations. Make enquiries about the appli-

cable disposal regulations where you live.

Open the battery compartment by removing

the lid.

Insert the batteries (2 x 1.5 V micro, for

example R03 or AAA). Observe the po-

larity marked in the bottom of the battery

compartment.

Close the battery compartment.

note:-

If the television no longer reacts properly

to remote control commands, the batteries

may be flat. Always remove used batteries.

The manufacturer accepts no liability for

damage caused by leaking batteries.

-9

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

overview_{-------------------------------------------------------------------------------------------------------------------------------------}

Connections-on-the-television-set

spDiF-

Socket for audio output

(coaxial) for PCM/AC3

signals.

For connecting digital AV

amplifiers or AV receivers.

sAtellite

Av1

Antenna socket for the

satellite antenna (DVB-S).

SCART socket (FBAS signal,

RGB signal).

AuDio-out-l-r Sockets for audio output.

optical-out

Socket for audio output

(optical) for PCM/AC3

signals.

For connecting digital AV

amplifiers or AV receivers.

Component

Y-pb-pr

Sockets for video input

(YUV signal).

l--r

Sockets for audio input

(YUV signal).

-10

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

overview_{-------------------------------------------------------------------------------------------------------------------------------------}

pC-Audio

Socket for audio

input for a PC.

Controls-on-the-television-set

8/i-

Switches the television on and

back into standby mode.

The only way to disconnect the

television from the mains supply

is to pull the plug.

pC-in

VGA socket, video input

for PC.

Ant-in

Antenna socket for a DVB-T,

DVB-C and analogue

antenna.

v–--v+

menu-

Adjusts the volume;

selects menu functions.

hDmi2

hDmi3

hDmi4

usB-hDD

HDMI socket,

audio/video input.

-Opens the menu.

Select a menu option with

»p+« or »p–«.

HDMI socket,

audio/video input.

Activate the function with

»v+« or »v–«.

HDMI socket,

audio/video input.

Confirm the function with

»v+« or »v–«.

-USB socket for external

data media without a power

supply of their own and

PVR function.

Press »menu« to quit the menu.

Opens the pre-selection for

AV channels.

In the menu, press »p+« or »p–«

to select and press »v+« or »v–«

to confirm.

Headphone jack (3.5 mm

jack plug).

s-vhs

video

l--r

Video socket for

p–--p+

Switches the television on from

standby;

selects channels in steps;

selects function in the menu.

S-Video camcorder.

Video socket for

camcorder.

Audio socket for

camcorder.

hDmi1

usB-

HDMI socket,

audio/video input.

-USB socket for external

data media and

PVR function.

Ci- -

-Common Interface Slot.

-11

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

overview_{-------------------------------------------------------------------------------------------------------------------------------------}

the-remote-control-–-main-functions

Switches on from standby;

Selects channel – directly

Switches on and off

(Standby).

Selects the channel list

(»All«, »FAV 1« to »FAV 4«).

Switches between

teletext and TV mode.

Opens the selection menu to

change picture formats.

Opens the »HDMI CEC De-

vice List«.

Then select with » « or » «

and press »oK« to confirm.

Displays information.

-Zapping function;

switches back one menu

level in the menus.

Opens the main menu

-Opens the channel list.

Opens the electronic

TV guide.

Opens the TOOLS menu.

Adjusts the volume.

Opens menu for AV channels

and USB input.

Then select using »

v«, » «,

» « or » « and press »oK«

to confirm.

Muting

Switches on from standby;

Selects channel – in steps.

Record, play, pause and

stop (only digital television

channels - to/from external

USB device).

Opens the »PRnP« menu.

navigation-in-the-menus

and down in the menus.

right in the menus.

-Activates various functions and

save functions/settings.

-12

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

overview_{-------------------------------------------------------------------------------------------------------------------------------------}

Stops scrolling through pages in

teletext;

Starts a fast reverse search in the

file browser.

the-remote-control-–--

All-functions

» «-

Selects pages in teletext.

(red)



« (green)Selects/activates various functions







Reveals answers in teletext;

Starts a fast forward search in the

file browser.

« (yellow)

« (blue)

in the menus.

Starts the recording (

television channels

is made on an external data me-

dium).

only for digital

, the recording



Selects different subtitles

(only for digital television channels)

Selects different audio languages

(only for digital television channels)

Starts playing a programme from

an external data medium;

Repeats a recorded programme.

Freeze frame, if no external data

medium is connected;

Playback pause;

Time shift mode (only for digital

television channels and when

an external data medium is con-

nected).

Ends playback of a programme

from an external data medium;

Ends a recording or

playback in time shift mode.

Splits the screen in teletext.

Switches to double character size

in teletext;

Selects the next title/next picture in

the file browser.

Refreshes a teletext page;

Selects the previous track/previous

picture in the file browser.

-13

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

selecting-language,-country-and-

operating-mode

initial-set-up-and-tuning-

-television-channels

The television set is equipped with automatic

channel search, which searches for satellite chan-

nels (DVB-S), terrestrial channels (DVB-T), cable

channels (DVB-C) and analogue channels.

Switch on the television set from standby with

»8«, »1…0« or »p+« or »p-«.

– During initial set-up, the »Installation Guide«

will be displayed.

You start the search and can then copy the tel-

evision channels into four favourite lists and sort

them there into your order of preference.

help:-

If this menu is not displayed, restore the

television set to its default settings (see

page 42).

For DVB-S channels there are 6000 presets

available, for DVB-T and DVB-C channels 1000

presets, and 100 presets for analogue channels.

2- Select the menu language with » «, » «,

»v« or »

Λ« and press »oK« to confirm.

3- Select the mode with » « or » « and press

the-various-settings

»oK« to confirm.

Depending on the type of antenna connected,

you can decide which channels you would like

the television to search for.

– The settings used in »Home Mode« help to

save energy.

– Alternatively, the menu item »Shop Mode«

can be selected which the retailer can use

for demonstrating the device functions.

Tunes digital television channels from the satel-

lite, from page 15.

You have two options for this search:

– the basic installation which presets a stand-

ard selection, e.g. the satellite Astra 19.2°

East; you need only start the search;

– the professional installation, which allows

you to make all required settings and set pa-

rameters for your receiver system.

note:

End the »Shop Mode« by restoring the televi-

sion set to its default settings (see page 42).

4- Select the country in which the television set

is operated with » «, » «, »v« or »Λ« and

press »oK« to confirm.

– The »Source Setup« menu appears with the

»Connection Type« line marked.

Tunes digital terrestrial television channels, on

page 17.

note:

Tunes digital television channels from the

You can find a description of how to tune

cable provider, on page 17.

the television channel of your choice – de-

pending on the antenna connected – in the

following chapters.

Tunes analogue television channels, in the

chapter “Special functions”, starting on

page 56.

Further settings for digital television channels

after the initial set-up can also be found in

the chapter “Special functions”, starting on

page 51.

note:-

Make the language and country selection for

all types, then continue reading the respective

chapter.

-14

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

Advanced-installation

tuning-the-television-channels-

from-satellite-(DvB-s)

You have two options for tuning digital satellite

channels.

In the »Source Setup« menu, in the »Connec-

tion Type« line, select the option »Satellite«

with » « or » «.

Select the line »Advanced Installation« with

The easy installation,

which pre-configures all antenna settings for

the satellite channels on Astra 19.2° East.

v« or »Λ« and press »oK« to confirm.

– The menu appears.

The advanced installation

20.09.2010

15:46

INSTALLATION

can be used if you wish to receive satellite

channels from various satellites. To do so,

you must make the antenna settings (Satel-

lite, LNB Power, LNB Type, DISEqC Mode,

LNB Selection) for the satellites chosen.

ANTENNA SETTINGS

Satellite

ASTRA 2A°,E

10714 MHZ H

Off

Transponder

LNB Power

LNB Type

easy-installation

Universal

Auto

In the »Source Setup« menu, in the »Connec-

tion Type« line, select the option »Satellite«

with » « or » «.

22 kHz

DISEqC Mode

LNB Selection

Off

1/4

Select the line »Easy Installation« with »

or » « and press »oK« to confirm.

v«

Low

Normal

Good

Quality

– Other menu options will be displayed,

the satellite Astra 19.2° East is preset.

Signal strength

Exit

Auto Tuning

Back

Start the scan with » « (green).



Manual Tuning

– The »Search results« menu appears, and

the scan for TV channels begins.

– Depending on the number of television

channels received, this can easily take a

few minutes.

Select the line »Satellite« with »

v« or »Λ«

and press »oK« to confirm.

– The »SELECT SATELLITE« menu appears.

Select the satellites with »v«, »Λ«, » « or

– The scan is complete as soon as the »PRO-

GRAM TABLE« appears.

» « and press »oK« to confirm.

note:

The setting in the line »Transponder« is not

required for this automatic scan.

You can abort the scan by pressing

»menu«.

Select the line »LNB Power« with »

v« or

Λ«.

Depending on the type of LNB, set the LNB

power supply to »13/18 V« or »14/19 V«

with » « or » «.

Select the line »LNB Type« with »v« or »Λ«

and press »oK« to confirm.

Select the type of LNB installed with » «

or » «.

Save the selection with

« (green) or abort



the action with » «-(red)



-15

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

6- Select the line »DISEqC Mode« with »

v«

11 Start the scan with » «-(red).



or »Λ«.

– The »Results« menu appears, and the scan

for TV channels begins.

Select »DiSEqC 1.0« or »DiSEqC 1.1« in

accordance with the existing antenna system

with » « or » «.

– Depending on the number of television

channels received, this can easily take a

few minutes.

– The scan is complete as soon as the »PRO-

GRAM TABLE« appears.

– DiSEqC 1.0 allows up to four satellites to

be received simultaneously.

– DiSEqC 1.1 allows up to 16 satellites to be

received simultaneously.

note:

7- Select the line »LNB Selection« with »

«.

v« or

You can abort the scan by pressing

»menu«.

»Λ

Select the setting for the respective satellites

with » « or » «.

12 Press »menu« to end the setting.

note:

8- Once the settings for the satellite have been

If other television channels are to be tuned

from a second satellite, proceed as follows:

made, switch to the »AUTOMATIC CHAN-

NEL SEARCH« menu with » «-(red).



Open the menu with »menu«, select the

line »SOURCE SETUP« with »v« or »Λ«

20.09.2010

15:46

SOURCE SETUP

AUTOMATIC CHANNEL SEARCH

and press »oK« to confirm. Then select the

»Automatic Channel Search« with » « or

« and press »oK« to confirm. Confirm

the line »Select Satellite« with »oK« and

select the preferred satellite with » «, » «,

»Λ

Connection Type

Satellite

Select Satellite

Scan Mode

ASTRA 2A , E

Free + Scramble

» « or » «. Start the scan with » «-(red).



Service Type

Network Search

Radio + TV

Off

Continue the adjustment by step 7 of the

chapter.

Exit

Start Search

Back

Select the line »Scan Mode« with »

or » «.

Select the scan mode with » « or » «

(for unencrypted channels, for encrypted

channels only, or for both).

v«

10 Select the line »Service Type« with »

or » «.

Use » « or » « to select whether you want to

v«

search for television channels only (TV), radio

stations only (Radio) or both (Radio + TV).

-16

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

tuning-terrestrial-television-

channels-(DvB-t)

tuning-television-channels-from-

the-cable-provider-(DvB-C)

In the »Source Setup« menu, in the »Connec-

tion Type« line, select the option »Cable«

with » « or » «.

In the »Source Setup« menu, in the »Connec-

tion Type« line, select the option »Air« with

» « or » «.

Select the line »Scan Type« with »

«.

Use » « or » « to set the required scan

v« or

Select the line »Scan Type« with »

«.

Use » « or » « to set the required scan

v« or

»Λ

type:

– »DTV«, scan for digital television channels;

– »ATV«, scan for analogue television

channels;

– »DTV«, scan for digital television channels;

– »ATV«, scan for analogue television

channels;

–

»ATV & DTV«, scan for analogue and

digital television channels.

–

»ATV & DTV«, scan for analogue and

digital television channels.

Select the »Scan Type« with »v« or »Λ«. Se-

Caution:

lect the preferred option (»Quick« or »Full«)

with » « or » «.

The antenna power supply (5V ) may only

be switched on if the antenna is an active

indoor antenna with a signal amplifier and it

is not already supplied with a voltage via a

mains plug (or similar supply). Otherwise

you may cause a short circuit and irrepara-

bly damage your antenna.

– The search function »Quick« sets up the

channels according to the information pro-

vided by your cable provider in the trans-

mission signal.

– If the option »Full« is selected, the entire

frequency range will be scanned. The

search can take a long time with this op-

tion. This option is recommended if your

cable provider does not support the scan

Selectthe»ActiveAntennaPower«with»

or » «.

v«

Switch on the antenna power supply for the

antenna with » « or » « (»On«).



type

»Quick«.

Start the scan with » « (green).

note:

– The »Search Results« menu appears, and

the search for TV channels begins.

– Depending on the number of television

channels received, this can easily take a

few minutes.

You can accelerate the search. To do this,

you need information about the frequency

and network ID. You are usually able to get

this data from your cable operator or find it

in forums on the Internet.

– The scan is complete as soon as the »PRO-

GRAM TABLE« appears.

Start the scan with » « (green).



–

The »Search Results« menu appears, and

the search for TV channels begins.

note:

You can abort the scan by pressing

»menu«.

– Depending on the number of television

channels received, this can easily take a

few minutes.

– The scan is complete as soon as the »PRO-

GRAM TABLE« appears.

Press »menu« to end the setting.

note:

You can abort the scan by pressing

»menu«.

Press »menu« to end the setting.

-17

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

selecting-channel-lists

Changing-the-program-table-for-

the-digital-channels

Open the menu with »menu«.

Channels which are found using the scan are

saved in the »PROGRAM TABLE«.

Select the »SOURCE SETUP« menu with »v«

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

You can delete channels which are not required

from the programe table, and lock individual

channels (Parental control).

Select the line »Programe Table« with »v«

or »Λ« and press »oK« to confirm.

– The menu »PROGRAM TABLE« appears.

You can also add channels to the favourites list;

in addition, you can change the order of chan-

nels within the favourites list.

important:

Programe table and favourites lists are

saved separately according to the different

input sources (satellite, cable, air).

With » « (green) you can display the channels



which belong to one network.

When opening the programme table, the

respective channel list for the current input

signal appears.

Switch to the next page in the programe table

with »p+« and to the previous page with »p-«.

With »

« (yellow) you can open the »LIST



MANAGEMENT« within the programe table.

INSTALLATION

PROGRAM TABLE

Network ALL

Das Erste

ZDF

SAT1

N24

3sat

SAT3

1 Das Erste

DTV

HD Sport

HD Test

10 RTL

DTV

11 HD 1

12 Life

13 Film

14 Promo

15 Sport1

DTV

16 TV Sport

17 Sat.8

18 SKY

19 TV6

20 TV5

DTV

Edit

Network

Manage lists

Sorting

Exit

Select favourites

Back

-18

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

notes:

Creating-lists-of-favourites

You can save your favourite channels in up to

four favourites lists (FAV 1 to FAV 4).

Repeat steps 2 and 3 if you would like to

change other channels within the same

favourites list.

notes:

Repeat steps 1 to 3 if you would like to

change other channels in a different favour-

ites list.

Favourites lists must be created separately

for all input sources (satellite, cable and air).

You can select the favourites list by pressing

»FAv«.

Exit the current favourites list with »

(blue).

– The entire programe table will appear

again.



In the »PROGRAM TABLE« menu, switch over

to the list view with » « (yellow).



Select the channel of your choice with »

or »Λ«.

v«

Deleting-channels

In the »PROGRAM TABLE« menu, select the

television channel to be deleted with «,

» « or » « and press » «-(red) to con-

“Push” the channel into the favourites

lists 1 to 4 with » « or » « and press »oK«

»Λ«,



to confirm.

firm.

– The position in the favourites list is marked

with »✔«.

– You can enter the same channel in more

than one favourite list.

– Each favourite list can store up to 255

channels.

Deletethecurrentchannelwith» «(yellow);

delete all channels with »



« (blue).



Confirm the deletion process with »

(green).



Quit the deletion process with » «.

note:

Channels can also be deleted from the

skipping-channels

You can mark television channels which should

be skipped when selecting with » « or » «.

It is still possible to select them using the number

buttons.

favourites lists. Select the channel to be

deleted with »

v«, »Λ«, » « or » « and

press »oK« to delete it.

When deleting a channel from the favourites

list, the order within the favourites list will be

updated.

In the »PROGRAM TABLE« menu, switch over

to the list view with » « (yellow).



Press »menu« to end the set-up.

Select the preferred channel with »

or »Λ«.

v«

sorting-channels-in-the-favourite-list

You can change the order of channels in the

favourites list.

Select the column »Skip« with » « or » «

and use »oK« to mark the channel.

– The channel is marked by »✔«.

In the »PROGRAM TABLE« menu, select the

favourites list »1« to »4«.

note:

2- Select the channel which should be moved

with » «, » «, » « or » « and mark it with

» «-(red).

Channels can also be reactivated. Select the

channel with »v« or »Λ«, then select the

column »Skip« and reactivate the channel

with »oK«.



Move the channel to its new position with

«, » «, » « or » « and press »oK« to

confirm.

-19

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

notes:

picture-settings-

You can only select the »Mpeg NR« function

Open the menu with »menu«.

on digital and AV presets.

Select the menu item »PICTURE SETTINGS«

»Mpeg NR« reduces any interference from

artefacts (pixel blocks) from digital pro-

grammes due to MPEG compression (such

as from DVB-T receivers or DVD players).

The »Film Mode« detects and processes

feature films automatically for all channel

sources. This means you will always receive

an optimal picture.

with »

v« or »Λ« and press »oK« to con-

firm.

20.09.2010

15:46

PICTURE SETTINGS

Picture Mode

Brightness

Contrast

User

This functions in the modi 480i, 576i and

1080i in TV playback and for other channel

sources.

100

If the »Film mode« is switched on for pro-

grammes without a feature film signal, minor

problems such as picture freeze, defective

subtitles or fine lines in the picture could

occur.

Sharpness

Colour

Colour Temperature

Medium

Enhanced picture settings

The function »Dynamic Contrast« adapts the

contrast dynamically and optimally for the

respective picture content.

With »Dynamic Backlight«, the device opti-

mally adapts the background lighting to the

picture content.

The »Backlight« can only be set manually

when the function »Dynamic Backlight« is

deactivated.

»MEMC« (Motion Estimation, Motion Com-

pensation) provides fluidity for the picture

in active pictures or fast camera shots.

»MEMC« will only appear in menus of LCD

products with 200 Hz PPR Feature and LED

products with 400 Hz PPR feature.

DNR

Off

Mpeg NR.

Exit

Back

– The »PICTURE SETTINGS« menu appears.

Select the line »Picture Mode«, »Bright-

ness«, »Contrast«, »Sharpness«, »Colour«, or

»Colour Temperature« with »v« or »Λ«.

Select the value with » « or » « and press

»oK« to confirm.

notes:

When changing the values with » « or

» «, the screen will be split. You can see

the current setting on the left side, the new

setting on the right side.

Press »menu« to end the setting.

In the »PICTURE SETTINGS« menu you can

also find other additional settings.

Select the line »DNR«, »Mpeg NR«, »Vibrant

Colour«, »Perfect Clear«, »Film Mode«,

»Gamma«, »Dynamic Contrast«, »Dynamic

Backlight«, »Backlight« or »MEMC« with

»v« or »Λ«.

Select the value with » « or » « and press

»oK« to confirm.

-20

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

Automatic-volume

sound-settings-

Television stations broadcast at different vol-

umes. The automatic volume limiting (AVL) func-

tion means the volume is kept the same when

you switch between channels.

Open the menu with »menu«.

Select the menu item »SOUND SETTINGS«

with »

v« or »Λ« and press »oK« to con-

firm.

Select the line »AVL« with »

v« or »Λ« and

– The »SOUND SETTINGS« menu appears.

select the option »On« with » « or » «.

note:

Additional operations are explained in the

following sections.

If the »SRS« setting has been selected in the

»Audio Mode« line, the AVL line cannot be

selected.

20.09.2010

15:46

stereo/two-channel-sound,-mono

If the device receives two-channel-sound pro-

grammes, e.g. a film with the original soundtrack

on audio channel B (display: »Dual II«) and

the dubbed version on sound channel A (dis-

play: »Dual I«), you can select the audio channel

you prefer.

Volume

Balance

Sound Type

Sound Mode

Stereo

If the device receives stereo or Nicam pro-

grammes, it switches automatically to stereo

sound (display: »Stereo«).

Sound Preset

Naturel

External

Headphone

You can switch the sound to »Mono« if the stereo

sound quality is poor.

Select the line »Audio Type« with »

v« or

Exit

Back

»Λ

« and adjust the setting with » « or » «.

stereo-width

This broadens the sound output for stereo pro-

grammes and improves the sound with mono

reception.

volume

Select the line »Volume« with »

and change the setting with » « or » «.

« or »

Select the line »Audio Mode« with »

or » «.

v«

Balance

Select the line »Balance« with »

and change the setting with » « or » «.

« or »

Select the option »Spatial« with » « or » «.

-21

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

soundeffects

equalizer

This menu offers three preset sound effects

(Music, Natural and Speech) and one setting to

be created by you (User).

Equalizer offers a sound setting that you can cre-

ate.

Equaliser appears in the menu when »Sound

mode« is selected as »Spatial« or »Normal«,

and »Sound Preset« as »User«.

Select the line »Sound Preset« with »

v« or

Λ«.

Select »Equalizer« with »v« or »Λ« and

Select the sound effect »Music«, »Natural«

or »Speech« by pressing » « or » «.

press »oK« to confirm.

The »EQUALIZER« menu appears.

note:

»User« option is active when »Sound mode«

setting is selected as »Normal or »Spatial«.

If the »SRS« setting has been selected in the

»Sound Mode« line, the »Equalizer« line

will not indicate.

srs-trusurround-xt*

SRS TruSurround XT is a patented audio tech-

nology which is integrated into the television set

and only requires the built-in speakers to gener-

ate a Surround Sound effect.

Select the frequency bandwidth »120Hz«

with »v« or »Λ«.

Set the preferred value with » « or » «.

Set the next frequency bandwidth with »

or » « and repeat the setting.

v«

Select the line »Audio Mode« with »

or » «.

Press » « to save the setting.

Select the option »SRS« with » « or » «.

Audio-description-(Audio-subtitles)

Select the line »Sound Preset« with »

or » «.

Audio description is an additional audio channel

for visually-impaired persons. Descriptions are

provided of activities, surroundings, changes of

scene, gestures and actors' facial expressions.

Select the sound effect »Music«, »Natural«

or »Speech« with » « or » «.

This audio channel is transmitted simultaneously

with the normal sound on digital channels. Avail-

ability depends on the respective channel and

broadcaster.

Select the line »Audio Description« with »

or »Λ

« and select the option »On« with » «

or » «.

Select the line »Volume« with »

« or »

and change the volume with » « or » «.

exiting-the-setting

Press »menu« to end the setting.

* Under licence from SRS Labs, Inc. TruSurround XT,

SRS and the

symbol are trademarks of

SRS Labs, Inc.

-22

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

television---operAtion_{--------------------------------------------------------------------------------}

Displaying-information

Basic-functions

1- Display information with »?«.

– The display disappears automatically after

a short while.

switching-on-and-off

Press »8«, »1…0« or »p+« or »p-« to switch

on the television from standby mode.

Freeze-frame

Press »8« to switch the television to standby.

If you wish to view a particular scene for longer,

you can “freeze” the frame of the current pro-

gramme.

selecting-channels

Press »1…0« to select presets directly.

Activate the freeze-frame function with »$«.

End the freeze-frame function with »$«.

note:

Select channels step by step with »p+« or

»p-«.

3- Open the channel list with »oK«, select the

preferred television channel with » «, » «,

» « or » « and press »oK« to confirm.

If an external data medium is connected

to the television, the time shift function is

activated with »$«. The time shift function is

described on page 29.

Exit the channel list with »menu«.

selecting-channels-from-lists

You can select channels from various lists (e.g.

all channels, FAV 1 to FAV 4).

picture-settings

Various picture settings are available.

Press »FAv« to open an overview of pro-

grame tables.

Open the Tools menu with »tools«.

Select the menu item »Picture Mode« with

– The overview is displayed.

»v« or »Λ«.

Select a programe table with »Λ« or »v«

and open it with »oK«.

3- Select »User«, »Eco TV«, »Vivid«, »Natural«,

»Movie«, »Sports« or »Game« by pressing

» « or » «.

Select a television channel with »

«, »

Λ«,

» « or » « and press »oK« to confirm.

note:

Press »menu« to exit the programe table.

Picture setting »Game« can only be selected

in »HDMI«, »Component« and »PC« modes.

selecting-a-preset-Av-channel

Audio-settings

Various audio settings are available.

Open the »Select Source« menu with »

Select an AV preset with » «, »

» « and press »oK« to confirm.

«.

Λ«, » « or

Open the Tools menu with »tools«.

Use »1…0« to switch back to the television

channel.

Select the menu item »Sound Preset« with

»v« or »Λ«.

Adjusting-the-volume

Select the audio setting »User«, »Music«,

»Natural« or »Speech« by pressing » « or

Adjust the volume with »

«.

- -–

» «.

switching-sound-on/off

note:

Press » « to mute the sound or switch it

on again.

»User« option is active when »Sound mode«

setting is selected as »Normal or »Spatial«.

-23

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

television---operAtion_{--------------------------------------------------------------------------------}

Audio-language

electronic-tv-guide

Various languages are available on digital tele-

vision channels. This depends on the programme

being broadcast.

The electronic TV guide provides an overview of

all programmes that will be broadcast in the next

week (for digital channels only).

Open the selection menu with »

«.

Press »GuiDe« to display channel informa-

tion.

Select the language by pressing »

and press »oK« to confirm.

v« or »Λ«

notes:

Not all channels supply provide a detailed

subtitles

TV guide.

Various subtitles are available on digital televi-

sion channels. This depends on the programme

being broadcast.

Many broadcasters transmit the current

schedule, but do not offer detailed descrip-

tions.

Open the selection menu with » «.

There are broadcasters which do not pro-

vide any information at all.

Select the subtitles with »v« or »Λ« and

press »oK« to confirm.

Press »v« or »Λ« to select a television

channel.

Zoom-function

– Today's programmes on the television

channel selected are displayed.

– Inaddition,informationaboutthecurrentpro-

gramme is display with detailed information

about the channel.

Open the Tools menu with »tools«.

Select the menu item »Zoom« with »v« or

»Λ«.

3- Press- »oK« repeatedly to enlarge the

Switch to the information about the current

display in three steps.

programme with » «.

note:

eco-mode

This function allows you to reduce the power

consumption.

You can open and switch off the extensive

programme information with »?«.

Open the Tools menu with »tools«.

Select the menu item »Eco TV« with » « or »Λ«.

Press »

« to select information on the next

programme and, »

« to return to the infor-

mation for the current programme.

3- Switch on the Eco mode with » « or » «.

Select programmes on over the coming days

Switch the Eco mode off again with » « or » «.

with » « (green), and switch back to the cur-



rent day with » «-(red).



Zapping-function

This function remembers the channel you are

currently watching while you switch over to other

ones (zapping).

Switch back to the channel selection with

» «.

notes:

By pressing » « (yellow) twice, the pro-



Press »1…0« or »p+«, »p–« to select the

gramme of your choice can be added to the

memory timer.

channel to be stored in the zapping memory

and press » « to confirm.

Filter for certain programmes with »

Press »1…0« or »

Λ«, »v« to switch to



(blue), select the channel type with » «,

another television channel.

» «, »v« or »Λ« and press »oK« to con-

Press » « to switch between the saved

firm. Programmes which match the selected

channel type are displayed.

television channel and the last television

channel viewed.4-

with »menu«.

End the function

7- Quit the electronic TV guide with »menu«.

-24

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

television---operAtion_{--------------------------------------------------------------------------------}

»Auto«-format

Changing-the-picture-format

The picture format is automatically switched to

»16:9« for 16:9 programmes.

The television automatically switches to the 16:9

format if this format is detected via the SCART

socket.

The picture format is automatically switched to

»4:3« for 4:3 programmes.

Select the picture format with » «.

– The picture format (for example »16:9«) is

displayed.

»overscan«-format

– You can choose between the following

picture formats:

In this mode, HD pictures are not cropped by the

HDMI sockets or component sockets, and are

displayed in their original size. This only applies

in HDMI mode and for resolutions of 720p or

above.

»4:3«-format

The picture is shown in 4:3 format.

»16:9«-and-»14:9«-formats

For programmes in 4:3 format, the picture is

stretched horizontally if the »16:9« format or

»14:9« format is selected.

The picture geometry is stretched horizontally.

With actual 16:9 input sources (from a set-top box

on the SCART socket) the picture fills the screen

completely and with the correct geometry.

»subtitle«-format

If you cannot see the subtitles at the bottom of

the screen, select »Subtitle«.

»letterBox«-format-

The letterbox format is especially suitable for

programmes in 16:9 format.

The black borders which are usually at the top

and bottom of the screen are eliminated, 4:3 pic-

tures fill the screen.

The transmitted pictures are enlarged, but are

slightly cropped at the top and bottom. The pic-

ture geometry remains unchanged.

»panorama«-format-

This setting is suitable for films in an especially

wide format.

During programmes in 4:3 format, the picture is

stretched horizontally if the »Panorama« function

is selected. The picture geometry is stretched

horizontally.

-25

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

possible-limitations-when-using-

an-external-data-medium

Depending on the broadcaster, you may experi-

ence various restrictions on some of the functions

from some television channels.

information-on-recording-and-

playing-television-programmes

Recording and playback of television pro-

grammes is only possible with digital television

channels (DVB-S, DVB-T and DVB-C).

■

The digital television channels (DVB-S, DVB-T

and DVB-C) you are able to record and play-

back also depends on the broadcaster.

GrunDiG-has-no-influence-on--

these-restrictions.

■

Recording a programme on the external data

■

Recording and playback of programmes,

medium can be disabled by the broadcaster.

If the message »URI* protected! PVR function

is blocked« appears on the screen, then re-

cording or timeshift is restricted (one recording

possible) or disabled (recording not possible)

by the broadcaster.

as well as the time shift function, can only be

carried out using an external data medium

(hard drive or USB stick). The data medium

should have a minimum storage capacity

of 2 GB.

* URI = User right information (Copyright in-

formation).

■

Recordings can be made with most data media

on the market. However, we cannot guarantee

operation for all data media.

■

If you record and save a programme on the

archive of an external data medium, playback

can be restricted.

The broadcaster can allow you to view this

programme one or more times, but it may only

be available for a certain period of time.

■

If a programme was recorded on an external

data medium, it can only be played back on

your television set. The playback of these pro-

grammes is not possible on other devices.

■

If you send your television to be repaired and

■

Programmes not suitable for minors will require

hardware components need to be replaced,

you might not be able to play the recordings

again on the repaired television.

the input of a PIN number immediately before

recording starts. If this authorisation is not

given, the recording may not start.

■

Reception for SKY broadcasting service is cur-

rently only possible in Germany with a suitable

set-top box.

■

Copying a programme from a digital television

channel onto a video or DVD recorder using

the »Av- 1« socket (analogue picture/

sound signal) can also be restricted by the

broadcaster. Prerequisite is that your device

supports the copying function.

-26

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

notes:

Connecting-external-data-media-

notes:

The »usB« socket of the television supplies

a maximum power of 500 mA in accord-

ance with USB specifications. External hard

disks which require more power may there-

fore only be connected to the »usB-hDD«

of the television.

Before connecting the data medium, switch

the television to standby with . Connect

»8«

the device and then switch the television on

again.

Before removing the external data medium,

the television must be switched to standby,

so that no data loss occurs.

If you use a network cable for external hard

disks which have been connected to the

»usB- hDD« socket of the television, this

network cable must also be disconnected

from the power supply when the television is

switched off.

Your television features two USB sockets,

»usB-hDD« and »usB«.

»usB-hDD« is used to connect data media,

which require an additional power supply

– for example, external hard disks.

External data media may not be disconnect-

ed from the television while files on the data

medium are being accessed.

settings-for-usB-recording

selecting-the-menu

Open the menu with »menu«.

Select the line »USB RECORDING« with

v« or »Λ« and press »oK« to confirm.

– The »USB RECORDING« menu appears.

20.09.2010

15:46

USB RECORDING

PRnP

Auto Preview

Connect the »usB- hDD« socket of the

television and the corresponding socket of

the data medium (external hard disk) using

a USB cable;

Manage data medium

Disk

USB

Partition

Check Disk

Insert the USB plug of the USB memory stick

into the »usB« socket of the television.

Capacity Used

1249

Used (MB)

Total (MB)

38145

Remaining SD recording time

Remaining HD recording time

1,008 min

288 min

Confirm the display »

(green).

– The file browser appears.

« with »



Exit

Back

-27

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

switching-on-automatic-preview

testing-the-external-data-medium

If the automatic preview is switched on, a pre-

view of the selected file appears in the file

browser.

You can subject external data media to a test

and establish whether they are suitable for the

chosen functionality.

Select the line »Auto Preview« with »

«.

v« or

Select the line »Disk« with »v« or »Λ«. If

»Λ

several data media are connected, select the

preferred data medium with » « or » «.

« or »

Switch on the function with » « or » «

(»On«).

Select the line »Partition« with »

Λ«.

If several partitions are available, select the

partition you wish to use with » « or » «.

Press »menu« to end the setting.

selecting-external-data-media

Select the line »Check Disk« with »

« or

If several external data media are connected to

the television, you can select the preferred data

medium.

Λ« and press »oK« to confirm.

Information on the data medium is dis-

played.

–

Select the line »Disk« with »

« or »

Press »menu« to end the setting.

Select the preferred data medium (»USB

HDD« or »USB«) with » « or » «.

Press »menu« to end the setting.

selecting-a-partition-on-the-external-

data-medium

If the external data medium features several par-

titions, select the partition you would like to use.

Select the line »Partition« with »v« or »Λ«.

Select the partition you wish to use with » «

or » «.

Press »menu« to end the setting.

-28

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

″pausing”-time-shift--

programmes

You can pause the programme you are watch-

ing. This is a useful function, for example if the

telephone rings while you are watching a film

and you do not want to miss anything.

recording-programmes

You can record programmes. The data for these

programmes is recorded on an external data

medium and this archive is administered via the

television.

The following approximate values apply for re-

cording:

Recording time for high-definition programmes

(HD) is 7 minutes with 1 GB of memory,

for standard programmes it is 26 minutes.

A freeze-frame display of the last scene appears

on the screen and the programme is recorded

in the time shift memory of the external data

medium.

While recording, you can watch another pro-

gramme from the archive.

In time shift mode you can record a maximum of

10 minutes of the current programme.

You cannot change presets.

Press »^!« to pause the current programme.

– The picture is frozen, the time shift and the

remaining recording time are displayed.

one-touch-programme-recording

Select the television channel to be recorded

Press »⁸« to resume the programme.

with » »1…0« or »p+«, »p–« and press

–

The programme will continue to be

recorded.

« to start the recording.

– Information on the recording is displayed:

the recording symbol, the channel name,

the programme, the recording time and the

available memory space.

note:

The following functions are possible when in

time shift mode:

– Rewind, press »3« several times accord-

ing to speed (the picture freezes while

rewinding);

– Fast forward, press »4« several times

according to speed;

– Select pause with »!«.

– After a short time this information disap-

pears; only the recording symbol flashes

on the top left of the screen.

End the recording with »⁷«.

notes:

After the recording is complete, the record-

Press »⁷« to quit the time shift function.

– The message »Live programme« appears,

and you will see the current programme

without time shift.

– The scenes in the “time shift memory” are

deleted.

ing will be automatically saved on the exter-

nal data medium.

The »RECORDED FILES« menu, with the ar-

chived programmes, can be opened with

»reC.list«.

If the external data medium is disconnected

from the USB socket during recording, the

recording will be stopped automatically

and will not be saved.

Play your recordings, that you have record-

ed with your FAT32 formatted HDDs, in USB

mode.

-29

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

recording-a-programme-from-the-

channel-list

presetting-programmes-to-be-

recorded

Open the »CHANNEL LIST« with »oK«.

Select a television channel with » «, »

» « or » « and press »oK« to confirm.

...-using-the-electronic-tv-guide

You can use data from the electronic TV guide

for recording.

Λ«,

Press »menu« to exit the channel list.

25 programmes can be preset for the timer

recording or as a reminder.

Press » « to start recording.

– Information on the recording is displayed:

the recording symbol, the channel name,

the programme, the recording time and the

available memory space.

– After a short time this information disap-

pears; only the recording symbol flashes

on the bottom right of the screen and the

recording time is displayed.

Press »GuiDe« to display channel informa-

tion.

– The electronic TV guide appears.

Select the preferred channel with »

v«

or »Λ«.

Switch to the information about the current

programme with » «.

Select the programme of your choice with

Press »⁷« to stop recording.

v« or »Λ«.

Confirm the programme with »

«.

– The symbol » « appears after the name

of the programme, and the data has been

added to the timer.

note:

If the data for the recording is to be changed,

use

« (yellow) and

« (blue) to





switch to the »SCHEDULED EVENTS«, press

«(green),changethedataandsaveitwith



« (green)

Press »menu« to exit the menu.

notes:

Before the timer recording begins, a warn-

ing message appears with a 20-second

countdown. You can switch over to the pro-

grammed television channel.

If the timer recording starts during playback,

playback is not interrupted: Recording takes

place automatically in the background as

long as you do not select »Yes« when the

timer countdown message is shown.

-30

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

...-by-manual-data-entry

You can preset up to 25 programmes for timer

recording.

editing-recording-data-in-the--

timer-menu

You can edit the data for programmed timer

recordings.

Press »GuiDe« to display channel informa-

tion.

– The electronic TV guide appears.

Select the timer menu by pressing »GuiDe«

 

sion.

« (yellow) and « (blue) in succes-

Open the »MAKE SCHEDULE« menu by

– The »SCHEDULED EVENTS« menu ap-

pears.

pressing » « (yellow) twice.



Select the line »Type« with »v« or »Λ«

Select the title of the programme to be

and select the option »Recording« with » «

changed with »

v« or »Λ« and activate the

or » «.

timer position with

« (green).



– The input menu is displayed.

Select the line »Channel« with »

« or »

and select the channel with » « or » «.

Select the required option with »

« and edit the data with »1…0« and

» « or » «.

v« or

»Λ

Select the line »Mode« with »v« or »Λ« and

select the preferred mode (»Once«, »Every

Day« or »Weekly«) with » « or » «.

4- Save the changes with » « (green).



– The timer has been changed.

Select the line »Start« (Start recording) with

« or » « and enter the date/time with

»1…0«.

Press »menu« to close the menu.

Deleting-a-timer

You can delete programmed timer recordings.

Select the line »End« (Stop recording) with

« or » « and enter the date/time with

»1…0«.

»v

Select the timer menu by pressing »GuiDe«

 

sion.

« (yellow) and « (blue) in succes-

8- Save the data with » « (green).



– The programme is preset.

– The »SCHEDULED EVENTS« menu ap-

pears.

Press »menu« to exit the menu.

notes:

Before the timer recording begins, a warn-

Select the title of the programme to be deleted

with »

with

v« or »

Λ« and delete the timer position

ing message appears with a 20-second

countdown. You can switch over to the pro-

grammed television channel.

« (yellow)



Press »menu« to close the menu.

If the timer recording starts during playback,

playback is not interrupted: recording takes

place automatically in the background as

long as you do not select »Yes« when the

timer countdown message is shown.

-31

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

playback

The recorded programmes – whether started

playback-during-a-recording

During a recording, you can either watch the

manually or using the timer function – are stored

programme you are currently recording or watch

on the external data medium. You can open the

a different one that you have already recorded.

archive on the external data medium by pressing

Select the channel to be recorded with

»1…0« or »p+«, »p–« and press »

start the recording.

»reC.list«.

« to

selecting-a-programme-from--

the-archive

Select the »Recorded Event« menu by press-

Open the »Recorded Event« menu with

ing »reC.list«. Select the programme you

»reC.list«

want with »

start playback.

The recording continues in the background.

v« or »Λ« and press »8« to

– The menu appears.

–

Select the programme of your choice with

v« or »Λ« and start playback with »8«.

Press »7« to end playback.

Press »⁷« to end playback.

– The television switches over to the current

television channel.

Press »⁷« to stop recording.

Deleting-programmes-in-the-

recording-list

Forward/reverse-picture-search

You can delete programmes from the record-

ing list.

During playback, select the fast forward

speed (2x, 4x, 8x or 16x) with »4«;

Open the »Recorded Event« menu with »reC.

list«

During playback, select the rewind speed

(2x, 4x, 8x or 16x) with »3« (the picture

freezes when rewinding).

– The menu appears.

Select the programme to be deleted with

v« or »Λ«.

repeating-a-scene-(A-B)

You can mark the starting and ending point of a

scene. The scene is then repeated continuously.

Press »

« (blue) to delete the programme.



Confirm the security query with



(green)

Mark the starting point A by pressing »⁸« at

the required scene during playback.

–

note:

You cannot delete programmes in the

»Recorded Event« menu which are currently

being recorded or played back.

This scene is marked as the starting

point A.

Mark the end point B by pressing »8«

once again at the required scene during

playback.

Press »menu« to close the menu.

– This scene is marked as the end point B.

– The television repeats the programme be-

tween these two points.

Quit the repeat function with »⁷«.

-32

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

image-data

File-formats

Your television can display pictures in the formats

JPEG, PNG and BMP.

Your television can work with the following file

formats using the USB sockets:

JPEG stands for Joint Picture Experts Group.

It denotes a process for compressing picture files.

PNG and BMP are process used to save image

data with no, or very little, losses.

Picture files can be stored with other types of files

on one medium.

These files can be organised into folders and

subfolders.

video-data

Special codecs for video compression and

decompression provide more memory space

without compromising the picture quality exces-

sively.

Your television plays video files in the formats

DIVS, XVID, H.264/MPEG-4 AVC (L4.1, 4 ref-

erence pictures), MPEG-4, MPEG-2, MPEG-1,

MJPEG and MOV.

The following file name extensions are also sup-

ported: AVI, MKV, MP4, TS, MOV, MPG, DAT.

These files can also contain audio files com-

pressed using MP3, AAC or Dolby Digital^©.

Audio-data

Your television can play audio data in the for-

mats MP3, AAC, WMA.

MP3 is the abbreviation for MPEG-1 Level 3 and

is based on the MPEG-1 standard, which was

developed by the MPEG (Motion Picture Expert

Group).

AAC stands for Advanced Audio Coding and

was also developed by MPEG. AAC provides

better sound quality at an identical data rate.

WMA (Windows Media Audio) is a compres-

sion standard for audio data developed by

Microsoft.

These formats allow audio files to be recorded

and played which sound as good as a CD, while

taking up only a fraction of the memory space.

File name extensions which are supported: MP3,

MP2, WMA, M4A, AAC.

MP3 files can be organised into folders and

subfolders, as on the computer.

-33

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

Connecting-external--

data-media-

Before connecting the data medium, switch the

television to standby using »8«. Connect the

device and then switch the television on again.

Before removing the external data medium,

the television set must be switched to standby,

so that no data loss occurs.

notes:

The »usB« socket of the television set

supplies a maximum power of 500 mA in

accordance with USB specifications. Exter-

nal hard disks which require more power

may therefore only be connected to the

»usB-hDD« of the television set.

Connect the »usB-hDD« socket of the tel-

evision and the corresponding socket on

the data device (external hard drive, digital

camera, card reader or MP3 player) using a

USB cable;

If you use a network cable for external

hard disks which are connected to the

»usB-hDD« socket on the television, this

network cable must also be disconnected

from the power supply when the television

is switched off.

External data media may not be disconnect-

ed from the television set while files on the

data medium are being accessed.

Insert the USB plug of the USB memory stick

into the »usB« socket of the television set.

Confirm the display »

(green)

– The file browser appears.

« with



A bi-directional data transfer as defined for

ITE (Information Technology Equipment)

devices in EN 55022/EN 55024 is not

possible.

USB transfer is not in itself an operating

mode. It is only an additional function.

-34

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

switching-on-automatic-preview

If this function is switched on, a preview of the

selected file then appears in the file browser.

the-file-browser-

The file browser displays video, audio and

picture files stored on external data media.

Select the line »Auto Preview« with »

v«

If an external data medium contains files in

different formats, you can, when necessary, filter

out the formats not required.

or »Λ«.

Switch on the function with » « or » «

(»On«).

main-menu-of-the-file-browser

Press »menu« to end the setting.

selecting-the-display-mode

Select »View Mode« with »v« or »Λ«.

VIDEO FILES

2- Select the preferred option with » « or » «.

ROOT

Photo

Music

Film

Press »menu« to end the setting.

setting-the-display-duration-for-

pictures-in-a-slideshow

Select »Slide Show Interval« with »v« or »Λ«.

USB DRIVE

Used (MB)

Total (MB)

475

Selectthedisplayduration(3, 5, 10 seconds)

with » « or » «.

Use Control

Buttons

Speed

All

Repeat

Now

Total

Press »menu« to end the setting.

Divx -voD

Selected data format.

Name of the data medium.

Total number of folders on the data medium.

You must have your device registered in order to

play the protected video that you will buy from

DivX .

Select »DivX VOD« with »v« or »Λ« and

4- Preview of the selected file.

confirm with »oK«.

– Registration Code appears.

5- Information on the external data medium.

Menu navigation.

Visit “http://vod.divx.com” and register the

device with the registration code.

settings-in-the-usB--

setup-menu

Press »menu« to end the setting.

DivX Certified® to play DivX® and DivX

Plus™ HD (H.264/MKV) video up to

1080p HD including premium content.

selecting-the-menu

Open the menu with »menu«.

Select the »SOURCE SETUP« menu item with

ABOUT DIVX VIDEO: DivX® is a digital video format created

by DivX, Inc. This is an official DivX Certified® device that plays

DivX video. Visit divx.com for more information and software

tools to convert your files into DivX video.

»v

« or »

Λ« and press »oK« to confirm.

–

The »USB SETUP« menu appears.

note:

ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® de-

vice must be registered in order to play purchased DivX Video-

on-Demand (VOD) movies. To obtain your registration code,

locate the DivX VOD section in your device USB setup menu.

Go to vod.divx.com for more information on how to complete

your registration.

Additional functions are explained in the

following sections.

-35

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

note:

Basic-playback-functions-

When playing picture data, the file browser

Select the data medium by pressing »

«,

switches off. Press » « to display the file

use » «, » «, » « or » « to select the option

browser again.

»USB« and press »oK« to confirm.

– The file browser appears.

Press »^!« to pause playback.

Select the file format (video files, audio files,

picture files) with » « or » «.

8- Press »⁸« to resume normal playback.

Press » « to end playback.

The file browser appears.

Switch to the folder/file list with »oK«.

note:

notes:

If two USB data media or one USB data

Use »Λ« to select »Up Folder«, when you

medium with several partitions is connected

to the USB sockets, the letter for the respec-

tive drive (e.g. C) appears behind the folder

symbol. Select the letter of the drive with

would like to return to the last folder. Use

»Root« (and then press »oK«) to return to

the main folder.

It is possible that files which are actually

supported do not function correctly in USB

mode. This is because certain files are not

recorded with standardised compression

processes, although they feature the “right”

file ending.

»v« or »Λ« and press »oK« to confirm.

Select the folder or file with »v« or »Λ« and

press »oK« to open it.

– A list of subdirectories appears.

note:

If a video file features several audio tracks

(audio streams), you can switch these over

during playback in full screen mode with »

«.

Switch back to the main folder with » «.

Select the track or picture with »

and press »⁸« to start playing.

You can view information on the film data by

pressing »?« (red).

v« or »Λ«

–

When playing music files, you can use other

options in the USB mode at the same time.

This way, you can, for example, enhance a

slideshow with music.

– When playing MP3 or WMA data, infor-

mation on the album, track and singer is

displayed at the left of the menu.

– When playing picture files, you can use

»?« to display information about the reso-

lution and size.

For films, only subtitles in the SRT format

are supported. The names of the subtitle

and film files must be identical. Otherwise,

no subtitles will be shown.

– When playing picture data, press »

?«

twice to enter the DivX Settings menu.

-36

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

selecting-a-certain-passage-for-

playback-

Additional-playback--

functions

Depending on the file format, the following

additional functions are available:

(video files only)

During playback, press »oK«.

Enter the passage (time) with »1-...-0« and

press » « (green) or »oK« to confirm.

selecting-chapters-on-Divx -files

(only video files)



Fast-forward

(for video and audio files only)

You can select different speeds (2-fold, 4-fold,

8-fold and 16-fold forwards and backwards).

During playback, select the next chapter

with » «.

During playback, select the previous

chapter with » «.

Select the playback speed during playback

with »3« or »4«.

note:

You can also select chapters by entering the

chapter number with »1...0«.

2- Press »⁸« to resume normal playback.

selecting-titles-on-Divx -files

(only video files)

rotating-pictures-

(picture files only)

During playback, select the next title with

«.

You can rotate pictures by 90°.

»Λ

During playback, press » « or « to rotate

the pictures by 90°.

During playback, select the previous title

with » «.

repeat-functions

Options:

playing-selected-titles

Only the marked tracks are played.

– »One Repeat«: the current track will be

repeated.

– »All Repeat«: all tracks will be repeated.

Select the titles with »

»oK« to mark it.

v« or »

Λ« and press

Open the Tools menu with »tools«.

Select the next title with »

« or » « and

press »oK« to mark it.

Select the menu item »Repeat« with »

v« or

»Λ«.

Start playback with »⁸«.

3- Select »All«, »Random«, »One« or »None«

Press » « to end playback.

by pressing » « or » «.

note:

To remove the marking, select the title with

« or » « and press »oK« to remove the

marking.

»v

selecting-a-track-or-picture-in-steps-

(sKip)

During playback, select the next track/

picture with »⁶«.

During playback, select the previous track/

picture with »⁵«.

– Playback begins with the track or picture

you selected.

-37

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

teletext-operAtion_{-----------------------------------------------------------------------------------------------}

enlarging-the-character-height

If you have difficulty reading the text on the

screen, you can increase the character height.

top-text-or-FloF-text-mode

Press »txt« to switch on teletext.

Select teletext pages directly with »1...0«

To enlarge the character height of a teletext

page, keep pressing »⁵«.

or step by step with »v« and »Λ«.

Return to teletext page 100 with »?«.

note:

page-hold

At the bottom of the screen there is an info

A multiple page may contain several sub-pages,

which are automatically scrolled by the broad-

casting station.

bar with red, green and – depending on the

channel – yellow and blue panels. Similarly,

the remote control also features buttons with

different colours with which these pages can

be selected.

Stop the automatic scrolling of the sub-pages

with »3«.

2- Quit the function with »3«.

Go back a page with » «-(red).



Go to the next page with » « (green).



opening-a-sub-page-directly

Select a particular chapter with



If the selected teletext page contains additional

pages, the number of the current sub-page and

the total number of pages are displayed.

(yellow)

6- Select a particular subject with »

« (blue).



1- Press » « to open the sub-page function.

2- Use »0…9« to enter the sub-page.

3- Quit the function with » «.

Quit teletext with »txt«.

normal-text-mode

Press »txt« to switch on teletext.

revealing-answers

Certain teletext pages contain hidden answers

or information.

Press »1…0« to select teletext pages directly.

Return to teletext page 100 with »?«.

Go back a page with »v«.

Display information with »4«.

Go to the next page with »Λ«.

2- Press »4« to conceal the information.

Quit teletext with »txt«.

split-screen

Additional-functions

This functions allows you to display the televi-

sion channel on the left side, the teletext on the

right side.

skipping-the-waiting-time

While a page search is progressing, you can

switch to the TV programme.

Switch the function on with »7«.

– The television channel and teletext are dis-

played next to each other.

Enter the teletext page number with »1…0«

and then press »⁶«.

Switch the function off with »⁷«.

– As soon as the page is found, the page

number is displayed.

Press »⁶« to switch to the teletext page.

-38

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConvenienCe-FunCtions_{-------------------------------------------------------------------------}

Changing-the-audio-language

(only for digital television channels)

opening-the-settinGs-menu

Open the menu with »menu«.

You can define a primary and a secondary

audio language.

Select the »SETTINGS« menu with »v« or

Λ« and press »oK« to confirm.

– The »SETTINGS« menu appears.

Select the line »Audio« with »v« or »Λ« and

press »oK« to confirm.

–

The »Select Audio Language« menu

20.09.2010

15:46

appears.

SETTINGS

Select the audio language with » «, » «,

»v« or »

Λ« and then use » «-(red) to set



Language settings

it as the primary audio language, or use

« (green) to set it as the secondary audio



English

language.

Audio

Subtitle

– The primary and secondary language is

display at the top right in the menu.

English

Off

Subtitle Mode

Date and time settings

Press »menu« to end the setting.

Changing-the-subtitle-language-

and-subtitle-mode

(only for digital television channels)

Date & Time

Time Adjustment

Time Zone

Auto

GMT +1

You can switch the subtitles on and off, select the

subtitle language and allocate a second subtitle

language.

Exit

Back

Select the line »Subtitle« with »v« or »Λ«

note:

and press »oK« to confirm.

– The »Select Subtitle Language« menu ap-

pears.

Additional operations are explained in the

following sections.

Select the subtitle language with »

v«,

language-settings

»Λ«, » « or » «, then use » «-(red) to set



it as the primary subtitle language, or use



Changing-the-menu-language

« (green) to set it as the secondary subti-

Select the line »menu« with »

v« or »Λ«

tle language.

and press »oK« to confirm.

– The primary and secondary language is

displayed at the top right in the menu.

–

The »Select Menu Language« menu

appears.

To go back one menu level, press » «.

2- Select the menu language with » «, » «,

Select the line »Subtitle Mode« with »v« or

»v« or »Λ« and press »oK« to confirm.

Λ« and then set the preferred option »Off«,

Press »menu« to finish the setting.

»Hard of Hearing« or »Basic« with » « or

» «.

Press »menu« to end the setting.

-39

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConvenienCe-FunCtions_{-------------------------------------------------------------------------}

setting-the-date-and-time

timer-settings

Your television set detects the difference in time

to Greenwich Mean Time (GMT) automatically,

as long as the channel selected transmits a time

signal. You can also set the difference in time

manually – for example, when the correct time

is not detected automatically or does not corre-

spond to local time for other reasons.

entering-the-switch-off-time--

(sleep-timer)

In the »Sleep Timer« menu you can enter a time

for the television to switch off. After this time

has elapsed, the television switches to standby

mode.

Select the line »Sleep Timer« with »

»Λ«.

v« or

Select the line »Time Adjustment« with »v«,

then select the option »Manual« with » «

Enter the switch-off time with » « or » «.

or » «.

– The lines »Time Zone« and »Daylight Sav-

ing« are active.

note:

To switch off the function, use » « or » « to

set the switch-off time to »Off«.

Select the line »Time Zone« with »v« and

press »oK« to confirm.

Press »menu« to end the set-up.

– The »Select Time Zone« menu appears.

switch-on-timer

3- Select the appropriate time zone with » » «,

In the »Auto On« menu you can enter a switch-on

time for the television. After the preset time has

elapsed, the television switches on from standby

– at the preselected volume and the preselected

television channel.

» «, »v

« or »

Select the line »Daylight Saving« with »

and use » « or » « to set the option »Auto«,

and press »oK« to confirm.

v«

»Off« or »On«.

Press »menu« to finish the setting.

note:

Select the line »Auto On« with

and press »oK« to confirm

« or »

Λ«

If the option »Auto« is selected in the line

Select the line »Mode« with

« or » and

Λ«

»Time Adjustment«, the television set auto-

matically adapts the time to the time signal

from the respective broadcaster. However,

different channels may also use time bases

which are different to those of your country;

e.g. foreign broadcasters. In these cases,

reminders and planned recordings may be

annulled due to the time difference.

use » « or » « to select when the television

should switch on.

Select the line »Input Source« with

»v« or »Λ«

and use » « or » « to select the input source.

Select the line »Service Type« with

»v« or »Λ«

and use » « or » « to select the preferred op-

tion (ATV, DTV, Radio or DATA).

Select the line »Channel« with

»v« or »Λ«

and use » « or » « to select the preferred

channel.

note:

The line »Channel« is only active when the in-

put signal currently in use has been set. If no

entry has been made, then the first channel of

the selected input source will be used.

-40

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConvenienCe-FunCtions_{-------------------------------------------------------------------------}

Select the line »Volume« with

« or »

and

parental-control-settings

Authorising-programmes

There are films which may be wholly or partially

unsuitable for children.

use » « or » « to set the volume.

Select the line »Set Hour« with

v« or »Λ«

and enter the time with »1…0«.

8- Save the data with » « (green).



These programmes contain information which

marks the content or scenes with access levels of

4 to 18. You can select one of the access levels,

thereby authorising playback.

note:

You can abort the entry by pressing » «-(red)



Press »menu« to end the setting.

Select the line »Parental Guidance« with

« or » « and press »oK« to confirm.

switch-off-timer

»v

In the »Auto Off« menu, you can enter a time

for the television to switch off. After this time has

elapsed, the television switches to standby mode.

Enter the PIN code »1234« with »1-...-0«.

Select the access level with » « or » «.

Press »menu« to end the setting.

Select the line »Auto Off« with

« or »

Λ«

and press »oK« to confirm

note:

Select the line »Mode« with

« or » and

Λ«

Parental Guidance is not enabled at USB

source.

use » « or » « to set the preferred mode.

Select the line »Set Hour« with

»v« or »Λ«

locking-menus

and enter the time with »1…0«.

This function allows you to lock the »Automatic

Channel Search«, »Digital Manual Tuning«, »An-

tenna Settings« and »Program Table« menus so

that they can be only accessed by entering a

PIN code.

4- Save the data with » « (green).



note:

You can abort the entry by pressing » «-



(red).

Select »Menu Lock« with »v« or »Λ«.

Press »menu« to end the setting.

Enter the PIN code »1234« with »1-...-0«.

Automatic-switch-off-(Auto-sleep)

Activate the lock with » « or » « (»On«).

If this function is activated, the television switches

automatically to standby after 5 minutes if no

video signal is broadcast or in accordance with

the according to European regulations, the tel-

evision switches automatically to standby after 4

hours provided that none of the buttons on the

remote control or on the television is operated

during this period.

Press »menu« to end the setting.

locking-keys-(parental-lock)

When the key lock is activated, the buttons on

the television set do not function.

Select the line »Keypad Lock« with »

«.

v« or

»Λ

Select the line »Auto Sleep« with »

v« or

Enter the PIN code »1234« with »1-...-0«.

»Λ«.

3- Activate (On) or deactivate (Off) the key lock

Activate the function with » « or » «

with » « or » «.

(»On«).

Press »menu« to end the setting.

note:

To switch off the function, use » « or » « to

select the setting »Off«.

Press »menu« to end the setting.

-41

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConvenienCe-FunCtions_{-------------------------------------------------------------------------}

Changing-the-pin-code

updating-software

You can also enter a personal PIN code instead

of the default code »1234«. Please take note of

your own PIN code.

(for digital channels only)

In the »SETTINGS« menu, select the line

»Check For Updates updates« with » « or

« and press »oK« to confirm.

Select »Set PIN« with »v« or »Λ« and press

»Λ

»oK« to confirm.

– A search for new software will be made

and – if available – it will be installed.

Enter the current PIN code 1 2 3 4 with

»1-...-0«.

note:

If a search for software updates should be

Enter your new four digit PIN code with

»1-...-0«.

made automatically, select the line »Auto-

matic OAD« with »v« or »Λ« and use » «

Enter your new four digit PIN code with

»1-...-0« again.

or » « to select the option »On«.

– The software will be updated automati-

cally as far as possible.

Press »menu« to end the setting.

locking-television-channels-

You can lock individual television channels, for

example channels unsuitable for children, using

a personal PIN code.

restoring-the-television-to-the-

default-settings

This function allows you to delete the channel

lists and all custom settings.

Open the menu with »menu«.

Select the »SOURCE SETUP« menu with »

or »Λ« and press »oK« to confirm.

v«

In the »SETTINGS« menu, select the line

»Restore Factory Defaults« with »v« or »Λ«

Select the line »Program Table« with »

v« or

and press »oK« to confirm.

»Λ« and press »oK« to confirm.

Press » « (green) to confirm the warning



– The »PROGRAM TABLE« menu is dis-

played.

message.

– The »Source Setup« menu appears.

In the »PROGRAM TABLE« menu, switch

Continue the settings with the chapter “Initial

set-up and tuning television channels” on

page 14.

over to the list view with » « (yellow).



Select the channel to be locked with »

v«

or »Λ«.

Select the column »Lock« with » « or » «

and press »oK« to lock the channel.

Enter the PIN code »1234« with »1-...-0«.

– The channel is marked using »✔«.

note:

To remove the lock, select the channel again

with »v« or »Λ«, press »oK« to confirm

and then enter the PIN code 1 2 3 4 using

»1-...-0«.

-42

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

searching-for-and-activating--

external-devices

You can connect up to 11 devices with DIGI LINK

functions to your television.

DiGi-linK

Your television is equipped with

the DIGI LINK function.

This function uses the CEC

(Consumer Electronics Control)

protocol.

Open the CEC device list with »CeC«.

– The »HDMI CEC Device List« appears.

CEC allows external devices which are connect-

ed to the »hDmi« sockets by an HDMI cable

(e.g. DVD player) to be operated with a remote

control.

Prerequisite is that the devices connected support

CEC. Read the operating manual for the external

device to find out how to activate the correspond-

ing function.

Start the device search with » «-(red).

The devices found are displayed in the

menu.



–

3- Select the device for operation with »

v«,

«, » « or » « and press »oK« to mark it.

– If the selected device is connected to a

different input to the current one, a switch

to the respective input will occur auto-

matically.

the-DiGi-linK-functions-on-your-

television

Press »menu« to end the setting.

switching-on-the-television--

automatically-from-standby

If the »Autom. switch-on TV« function is activated

(»On«), then once the external device (e.g.

DVD player) is switched on, the television also

switches on and the appropriate HDMI preset is

selected.

Automatic-selection-of-the-hDmi-

preset-on-the-television

If your television is switched on and you then

switch on the external device (e.g. DVD player),

the appropriate HDMI preset on the television

will be selected.

selecting-the-menu-language

The television menu language is automatically

selected on the external device (e.g. DVD player).

The external device must support this function.

switching-off-the-external-device-

automatically

If you switch your television to standby, the ex-

ternal device (if it is switched on) will also be

switched to standby.

DIGI LINK is always active on your television set.

-43

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

switching-the-device-to-standby

This option switches the external device to

standby.

Device-operation

You can decide whether external devices should

react to your television's remote control.

Press »

«, use »v«, »Λ«, » « or » « to

Press »

«, use »v«, »Λ«, » « or » « to

select the preset »HDMI1« to »HDMI4« and

press »oK« to confirm.

select the preset »HDMI1« to »HDMI4« and

press »oK« to confirm.

Open the menu with »menu«.

Select the menu item »SOURCE SETUP« with

v« or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select »Device Standby« with »v« or »Λ«

20.09.2010

15:46

and press »oK« to confirm.

SOURCE SETUP

– The external device switches itself off.

Source

HDMI1

DIGILINK

GRUNDIG DVD

RC Passthrough

Device Selection

Remote Control

Device Standby

Exit

Back

Select the line »Remote Control« with »

or » «.

v«

5- Select the type of operation (»RC Pass-

through«, »Deck« or »Tuner« with » « or

» «.

notes:

»RC Passthrough« can be used for all devices.

»Deck« and »Tuner« can be selected in ac-

cordance with the external device which

has been connected.

Try out which type of remote control opera-

tion the external device reacts to the best.

Read about the scope of functions of the

DIGILINK-compatible device in the respec-

tive operating manual.

Press »menu« to end the setting.

-44

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

high-definition--hD-ready

Connection-options

Which television socket(s) you connect your

Connect the cor-

external devices to depends on the sockets

the external device is equipped with and the

signals which are available.

responding input

sources (e.g. HDTV

receiver or HD-

DVD player) to the

»hDmi« sockets (for

digital HDTV sources).

Please note: With many external devices,

the resolution of the video signal must be

adjusted to the input sockets of the television

(see the operating manual of the external

device). You can find out which values you

need to set by referring to the guidelines in

the sections about the various connection

options.

This ensures that you can view digital HDTV

programmes, even if they are copy-protected

(HDCP High Bandwidth Digital Content Protec-

tion), without encountering problems.

Do not connect any other equipment while

the device is switched on. Also switch off the

other equipment before connecting it.

Do not plug in the power cord of the device

until you have connected the external equip-

ment and the antenna.

-45

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

...-using-the-sCArt-socket--

(FBAs/rGB-signal)

Connecting-external-devices

...-with-digital-audio/video-signals

Suitable devices: Digital satellite receiver,

Suitable devices: Digital satellite receivers,

DVD player/recorder, set-top box, games con-

sole, video recorder, decoder.

Video signal: FBAS/RGB.

Audio signal: stereo, analogue.

»AV1« preset.

Playstation, BluRay player, DVD player/

recorder, set-top box, notebook, PCs.

Video signal: Digital video; resolution: stand-

ard 576p; HDTV 720p, 1080i, 1080p.

Audio signal: digital audio (stereo, multi-chan-

Connect the »Av1« socket on the television and

the corresponding socket on the external device

using a SCART cable (video and audio signal).

nel compression, uncompressed).

Presets »HDMI 1«, »HDMI 2«, »HDMI 3« or

»HDMI 4«

Connect

the »hDmi1«, »hDmi2«,

Activating-a-decoder

»hDmi3« or »hDmi4« socket on the televi-

sion and the corresponding HDMI socket on

the external device using a standard HDMI

cable (digital video and audio signal).

If a decoder is connected to the »Av1« socket,

this must be activated to provide an unencrypted

video/audio signal.

Open the menu with »menu«.

...-with-analogue-video-signal-

(progressive)

Select »SETTINGS« with »v« or »Λ« and

press »oK« to confirm.

– The »SETTINGS« menu appears.

Suitable devices: DVD recorders/players,

games consoles.

Video signal: YUV; resolution: standard 576p;

HDTV 720p, 1080i, 1080p.

Audio signal: stereo, analogue.

Select the »Decoder« with »

v« or »Λ«.

Activate the function with » « or » «

(»On«).

Press »menu« to end the setting.

»YPBPR« preset.

Connect the »Component- Y- pb- pr«

sockets on the television to the correspond-

ing sockets of the external device with RCA

cables (video signal).

...-with-s-video-signal

Suitable devices: DVD player/recorder, video

recorder, camera recorder, notebook, PC.

Video signal: Y/C.

Audio signal: stereo, analogue.

»S-VHS« preset.

Connect the »Component-l-r« sockets

on the television to the corresponding sock-

ets of the external device with RCA cables

(audio signal).

1- Connect the »s-vhs« socket on the televi-

sion and the corresponding socket on the ex-

ternal device using an S-Video cable (video

signal).

Connect the »l--r« sockets on the television

to the corresponding sockets of the external

device with RCA cables (audio signal).

-46

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

Set the preferred volume with » « and » «.

...-with-an-analogue-tv-signal

Suitable devices: Digital satellite receiver,

Press »menu« to end the setting.

DVD player/recorder, set-top box, camera

recorder.

Video signal: FBAS.

Audio signal: stereo, analogue.

»AV2« preset.

note:

Prolonged listening with headphones at loud

volumes can damage your hearing.

hi-fi-system/Av-receiver

Connect the »video« socket on the television

to the corresponding socket of the external

device with an RCA cable (video signal).

Connecting-the-hi-fi-system/-

Av-receiver

1- Connect the »optical-out« socket on the

television to the corresponding socket of the

device with an optical digital cable (digital

audio signal);

Connect the »l--r« sockets on the television

to the corresponding sockets of the external

device with RCA cables (audio signal).

note:

There must not be a video signal at the

» video« and »s-vhs« socket at the same

time. This could lead to picture disturbances.

connect the »spDiF« socket on the television

to the corresponding socket of the AV receiv-

er with an RCA cable (digital audio signal).

using-a-DvD-player,-

DvD--recorder,-video-recorder--

or-set-top-box

setting-the-audio-format

You can select whether the audio signal out-

put via the »optical-out« or »spDiF« socket

should be in the PCM or AC2 format.

Switch on the external device and select the

function you wish to use.

Open the menu with »menu«.

Press

«, use »v«, »Λ«, » « or » « to

Select the menu item »SOUND SETTINGS«

select the preset for the input signal (»AV1«,

»AV2«, »S-VHS«, »HDMI1«, »HDMI2«,

»HDMI3«, »HDMI4« or »Component«)

and press »oK« to confirm.

with »

firm.

v« or »Λ« and press »oK« to con-

– The »SOUND SETTINGS« menu appears.

Select »Audio Output Setup« with » « or

Λ« and press »oK« to confirm.

headphones

– The menu appears.

Connecting-the-headphones

Select the »SPDIF output« with »v« or »Λ«.

Plug the headphone jack (3.5 mm ø jack

plug) into the headphone socket on the right

side of the television.

Select the preferred audio format (»PCM« or

»Dolby* D«) with » « or » «.

note:

Changing-the-headphone-volume

If you wish to output the audio only via a

multi-channel amplifier/AV receiver, set the

option »TV Speaker« to »Off« in the menu.

Open the menu with »menu«.

Select the menu item »SOUND SETTINGS«

with »

v« or »Λ« and press »oK« to con-

Press »menu« to end the setting.

firm.

– The »SOUND SETTINGS« menu ap-

pears.

Select the line »Headphone« with »

v« or

»Λ«.

-47

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

playing-the-audio-signal-via-the--

hiFi-system

1- Connect the »AuDio-out-l-r« sockets on

the television to the corresponding socket of

the AV receiver with an RCA cable (digital

audio signal).

note:

If this function is not activated, the audio sig-

nal is transmitted to the HiFi system/AV re-

ceiver (connected to »AuDio-out-l-r«).

Open the menu with »menu«.

Select the menu item »SOUND SETTINGS«

with »

v« or »Λ« and press »oK« to con-

firm.

– The »SOUND SETTINGS« menu appears.

Select »Audio Output Setup« with » « or

»Λ« and press »oK« to confirm.

– The menu appears.

Select the line »Audio Out« with »v« or »Λ«

and press » « or » « to activate the audio

output (»On«).

Select the line » Audio Out Status« with »

or » « and select the option »Fixed« or »Ad-

justable« with » « or » «.

v«

notes:

If you select »Adjustable«, the volume can

be changed in the menu option » Audio Out

Volume«.

If the audio should only be output via the

HiFi system/AV receiver, select the option

»Off« in the line »TV Speaker with » « or

» «.

Press »menu« to end the setting.

* “Dolby” and the double-D logo are trademarks of

Dolby Laboratories.

Manufactured under licence from Dolby Laborato-

ries.

-48

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-As-A-pC-monitor_{-----------------------------------------------------------}

Connecting-a-pC

20.09.2010

15:46

Connect the »pC-in« socket on the television

to the corresponding socket on the PC using

a VGA cable (video signal).

SOURCE SETUP

Connect the »pC-Audio« socket on the tel-

evision to the corresponding socket on the

PC using a suitable cable (audio signal).

Source

Auto Ajust

Extended settings

note:

Auto Ajust Mode

50H - 50V

Adjust your PC to the monitor (for example,

picture resolution 1280 x 768, picture fre-

quency 60 Hz).

Position

Size

Phase

selecting-presets-for-the-pC

Press »

« and use »v«, »Λ«, » « or » «

Exit

to select the preset »PC« and press »oK« to

confirm.

Back

Options:

settings-for-pC-mode

–

»Auto Ajust« for automatic PC configura-

tion.

Open the menu with »menu«.

– »Auto Ajust Mode«, select the option

»On« if the configuration should be imple-

mented automatically in PC mode.

– »Position« to configure the horizontal and

vertical picture position.

– »Size« to set the cycle frequency.

– »Phase« to eliminate flicker, unfocused

pictures or horizontal interference.

Select the »SOURCE SETUP« menu item with

v« or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

3- Select the function or setting with » « or

«, and then use » «, » « or » «, » « to

implement it.

Press »menu« to end the setting.

-49

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-with-A-Common-interFACe_{-------------------}

what-is-a-Common-interface?

Access-control-for-Ci-module-and-

smart-card

Common Interface (CI) is an interface for

DVB receivers.

Encrypted channels can only be viewed

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

v«

with a CA module suitable for the encryp-

tion system and in conjunction with the

corresponding smart card.

The television set is equipped with a Com-

mon Interface slot into which CI modules

from various providers can be inserted.

You can insert the provider’s smart card into

the CA module in order to enable the en-

crypted channels you wish to view.

– The »SOURCE SETUP« menu appears.

Select the line »CA-Module« with » « or

« and press »oK« to confirm.

notes:

This menu provides operating instructions

and – after you enter your PIN code – ac-

cess to the PAY-TV provider's channels.

inserting-the-CA-module

note:

The remaining settings are described in the

operating manuals for your CI module and

smart card.

Switch the device off before you insert a CA

module into the »Ci« slot.

CAM is not supported in certain countries

and regions; please consult your authorised

dealer.

Insert the corresponding smart card into the

CI module.

Insert the CI module with the smart card into

the »Ci« slot on the television.

Press »menu« to end the setting.

note:

In the »CA Module« sub-menu you can see

which CA module has been inserted in the

CI slot.

If you are inserting a CA module into the

CI slot of the television for the first time,

you will need to wait a moment until the

CA module is detected.

-50

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

Select the line »Scan Mode« with »

«.

Select the scan mode with » « or » «

(for unencrypted channels, for encrypted

channels only, or both).

v« or

searching-for-digital-television-

channels-from-a-satellite-auto-

matically

»Λ

Satellite data changes frequently, new chan-

nels are constantly being added. You should

therefore perform an automatic search from time

to time.

Select the line »Service Type« with »

«.

Use » « or » « to select whether you

v« or

»Λ

This searches all transponders for new channels.

want to search for television channels (TV)

only, radio stations only (Radio) or both

(Radio + TV).

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »v«

or »Λ« and press »oK« to confirm.

Select the line »Network Search« with »

or » «.

Select the option »On« with » « or » «

– If the »Network Search« is set to »On«,

the data will be accessed via the new

transponder of the network which has

been set.

v«

– The »SOURCE SETUP« menu appears.

20.09.2010

15:46

SOURCE SETUP

Source

Satellite

10 Start the scan with » «-(red).



Automatic Channel Search

Digital Manual Tuning

Antenna Settings

note:

If the previously stored channels should be

retained in the channel list and the new

channels found be added to it, then press

Program Table

« (green).





Signal Information

If » «-(red) is pressed, the saved channels

CA -Module

will be deleted from the current channel list.

Positioner settings

– The »Results« menu appears, and the scan

for TV channels begins.

Off

DiSEqC 1.2

– Depending on the number of television

channels received, this can easily take a

few minutes.

Exit

Back

– The search is complete as soon as the

»PROGRAM TABLE« appears.

Select the line »Source« with »v« or »Λ«

and press »oK« to confirm.

Select the input source »Satellite« with » «,

note:

» «, »

« or »

« and press »oK« to con-

You can abort the search by pressing

»menu«.

firm.

Select the line »Automatic Channel Search«

11 Press »menu« to end the setting.

with »

v« or »Λ« and press »oK« to con-

firm.

– The menu appears.

Select the line »Select Satellites« with »v« or

Λ« and press »oK« to confirm.

– The »SELECT SATELLITE« menu appears.

Select a satellite with »v« or »Λ« and press

»oK« to confirm.

-51

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

searching-for-digital-television--

channels-from-a-satellite-auto-

matically

If you know the parameters of a new television

channel, you can also search for it manually.

Current transponder data can be found in the

teletext, in satellite TV magazines or on the

Internet.

lnB-settings

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select »Antenna Settings« with »v« or »

and press »oK« to confirm.

– The »ANTENNA SETTINGS« menu ap-

pears.

Open the menu with »menu«.

Select the line required for the parameters

with »v« or »Λ«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

v«

– »Satellite«: »Press oK«, select a satellite

with » «, » «, » « or » « and press

– The »SOURCE SETUP« menu appears.

Select »Digital Manual Tuning « with » « or

« and press »oK« to confirm.

– The menu appears.

Select the line required for the parameters

with » « or » «.

»oK« to confirm.

– »Transponder«: »Press oK«, select a tran-

»Λ

sponder with » «, » «, »v« or »Λ« and

press »oK« to confirm. Use » «-(red) to



add a transponder, use » « (green) to



delete it, or use » « (yellow) to change

– »Frequency (MHz)«: Enter the five-digit

frequency with »1-...-0« .



transponder data.

– »LNB Power«: Set the LNB power supply

(depending on the type of LNB) to »Off«

»13/18 V« or »14/19 V« with » « or » «.

– »Symbol Rate (kS/s)«: Enter the five-digit

symbol rate with »1-...-0« .

– »Polarization«: Use » « or » « to set the

polarisation to »Horizontal« or »Vertical«.

– »Network Search«: use » « or » « to se-

– »LNB Type«: Select a type of LNB with » «

or » «. Use » « (green) to save the set-



lect the option »On« or »Off«.

– »Scan Mode«: Use » « or » « to select

ting, or use » «-(red) to abort.



– »22 KHz«: Depending on the LNB type,

22 kHz audio is selected. For a universal

LNB, this option is set to »Auto« and cannot

be changed.

whether you want to search for unencrypt-

ed (Unencrypted) channels only, encrypt-

ed (Encrypted) channels only, or for both

(Unencrypted + Encrypted).

– »DISEqC mode« and »LNB selection«:

depending on the type of antenna used,

use » « or » « select the option »Off«,

– »Service Type«: Use » « or » « to select

whether you want to search for television

channels only (TV), radio stations only

(Radio), or both (Radio + TV).

»DiSEqC 1.0« or »DiSEqC 1.1«.

»Off«: for a satellite system with only

one antenna.

Start the scan with » «-(red).

– The »Results« menu appears, and the scan

for TV channels begins.



»DiSEqC 1.0«: allows up to four satel-

lites to be received simultaneously.

Under »LNB selection«, use » « or

note:

» « to select the option »1/4«, »2/4«,

You can abort the search by pressing

»menu«.

»3/4« or »4/4«.

»DiSEqC 1.1«: allows up to 16 satel-

lites to be received simultaneously.

Press »menu« to end the setting.

Under »LNB selection«, use » « or

» « to select the option »1/16« to

»16/16«.

Press »menu« to end the setting.

-52

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

user-mode

settings-for-motorised-antennas-

(DiseqC-1.2)

Your television set supports motorised satellite

systems in compliance with DiSEqC 1.2. This

function allows the satellite antenna to be oper-

ated via the television set.

You can adjust the alignment of the satellite an-

tenna to each individual satellite. These settings

will be saved so that the antenna can later be

easily guided to each saved alignment.

Select the line »User mode« with »

or » « and press »oK« to confirm.

Open the menu with »menu«.

– The »USER MODE« menu appears.

Select the line »SOURCE SETUP« with »

v«

Select the preferred option with

»v«

or »Λ« and press »oK« to confirm.

or »

– »Satellite«: »Press oK«, select a satellite

with » «, » «, » « or » « and press

Λ«.

– The »SOURCE SETUP« menu appears.

Select the line »DiSEqC 1.2« with »

or »

Λ«. Select the option »On« with » «

»oK« to confirm.

or » «

– »Transponder«: »Press oK«, select the

– The line »User Mode« is active.

transponder from which the signal is being

note:

received with » «, » «, »v« or »Λ« and

Additional operations are explained in the

following sections.

press »oK« to confirm.

– »Moving Mode«: Use » « or » « to select

the option »Discrete« or »Continuous«.

– »Discrete«: Moves the antenna in defined

steps to the west and the east.

– »Continuous«: Moves the antenna to the

west or east continuously.

– »Step Size«: Use » « or » « to select the

number of steps with which the antenna

should turn. »Step Size« is only active

when the »Transport Mode« was set to

»Discrete«.

– »Move Motor«: Aligns the antenna with

the selected satellite. Use » « to align it to

»West«, use » « to align it to »East«.

– »Go To Stored Position«: Aligns the antenna

to a saved satellite position. Up to 50 posi-

tions can be saved. »Press oK« and then

select the saved position with » « or » «.

Press » « (green) to confirm – the anten-

na will be aligned with the saved position.



– »Store Stored Position«: The current anten-

na alignment is saved.

Press »menu« to end the setting.

-53

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

expert-mode

You can restrict the antenna's range or reset

the antenna.

searching-for-television-chan-

nels-from-the-cable-provider-

automatically

Select the line »Installer Mode« with »

« and press »oK« to confirm.

– The »INSTALLER MODE« menu appears.

« or

Open the menu with »menu«.

»Λ

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select the line »Source« with

or » « and press »oK« to confirm.

Select the option »Cable« with » «, » «,

Select the preferred option with

or » «.

»v«

– »Limit Position«: Defines the range in

which the antenna may move. Use » «

to set the western limit, use » « to set the

»v

« or »

Λ« and press »oK« to confirm.

eastern limit.

Select the line »Automatic Channel Scan«

– »Move Motor«: Aligns the antenna with

with »

firm.

v« or »Λ« and press »oK« to con-

the selected satellite. Use » « to align the

antenna to »west«, use » « to align the

– The menu appears.

antenna to »east«.

Select the line »Country« with »v« or »Λ«

– »Go To Stored Position«: Press »oK« to

save the current antenna alignment.

– »Store Stored Position«: Aligns the antenna

with the reference point of the positioner.

– »Reset DiSEqC 1.2 Limit«: Resets the limit

position of the antenna.

and press »oK« to confirm. In the country se-

lection menu, select the country with » «, » «,

»v

« or »

« and press »oK« to confirm.

Select the line »Scan Typ« with »

« or »

and set the option »DTV« with » « or » «.

Select the line »Cable Scan Type« with »

or »

with » « or » «.

v«

Λ« and set the option »Quick« or »Full«

– The search function »Quick« sets the chan-

nels according to the information provided

by your cable provide in the transmission

signal.

– If the option »Full« is selected, the entire fre-

quency range will be scanned. The search

can take a long time with this option. This

option is recommended if your cable pro-

vider does not support the search type

»Quick«

note:

You can accelerate the search. To do this,

you need information about the frequency

and network ID. You are usually able to get

this data from your cable operator or find it

in forums on the Internet. For example, the

frequency 402MHz and network ID 61441

can be entered for Germany.

-54

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

Start the scan with » «-(red).

– All channel and favourites lists will be

deleted and compiled anew.



searching-for-digital-terrestrial-

tv-channels-automatically

Open the menu with »menu«.

note:

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

After starting the scan, a security query will

appear. Press » « (green) to confirm the



– The »SOURCE SETUP« menu appears.

Select the line »Source« with

or » « and press »oK« to confirm.

Select the option »Air« with » «, » «, »

option »Yes«.

– The »Results« menu appears, and the scan

for TV channels begins. Depending on the

number of television channels received,

this can easily take a few minutes.

v« or

Λ« and press »oK« to confirm.

– The scan is complete as soon as the »PRO-

GRAM TABLE« appears.

Caution:

The antenna power supply (line »Active

Antenna Power«) may only be switched on

if the antenna is an active indoor antenna

with a signal amplifier and it is not already

supplied with a voltage via a mains plug

(or similar supply). Otherwise you may

cause a short circuit and irreparably dam-

age your antenna.

note:

You can abort the search by pressing

»menu«.

Press »menu« to end the setting.

searching-for-television-channels-

from-the-cable-provider-manu-

ally

Select the »Active Antenna Power« with »

or » «. Switch on the antenna power supply

for the antenna with » « or » « (»On«).

v«

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

Select the line »Automatic Channel Search«

or »Λ« and press »oK« to confirm.

with »

firm.

v« or »Λ« and press »oK« to con-

– The »SOURCE SETUP« menu appears.

– The menu appears.

Select the line »Source« with »v« or »

and press »oK« to confirm.

Select the line »Country« with »v« or »Λ«

Select the option »Cable« with » «, » «,

and press »oK« to confirm. In the country

»v

« or »

« and press »oK« to confirm.

selection menu, select the country with » «,

» «, »

« or »

Select the line »Scan Typ« with »

and set the option »DTV« with » « or » «.

« and press »oK« to confirm.

Select » Digital Manual Tuning« with »

v« or

v« or »Λ«

»Λ

« and press »oK« to confirm.

– The menu appears.

Start the scan with » «-(red).

– All channel and favourites lists will be

deleted and compiled anew.

Enter the four-digit frequency with »1-...-0«

and press »oK« to confirm.



–

The search starts after confirming, the

channels found are displayed in the »Re-

sults« menu.

note:

After starting the scan, a security query will

Press »menu« to finish the setting.

appear. Press » « (green) to confirm the



option »Yes«.

– The »Reults« menu appears, and the scan

for TV channels begins. Depending on the

number of television channels received,

this can easily take a few minutes.

– The scan is complete as soon as the

-55

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

»PROGRAM TABLE« appears.

tuning-analogue-television-

note:

-channels

You can abort the search by pressing

»menu«.

This setting is only necessary if you cannot re-

ceive any digital channels and you have not car-

ried out an analogue search during initial setup.

The television channels can be set directly or

using the scan.

Press »menu« to end the setting.

searching-for-digital-terrestrial-

tv-channels-manually

switching-the-television-to-

-analogue-reception

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

note:

or »Λ« and press »oK« to confirm.

Analogue channels can be selected if the

option »Air« or »Cable« has been selected.

– The »SOURCE SETUP« menu appears.

Select the line »Source« with »v« or »

Open the »Select input source« menu with »

«.

and press »oK« to confirm.

Select the option »Air« with » «, » «, »v« or

Depending on the antenna system, select the

Λ« and press »oK« to confirm.

option »Air« or »Cable« with »v«, »Λ«, » «

or » « as the input source and press »oK«

Caution:

to confirm.

The antenna power supply (line »Active

Antenna Power«) may only be switched on

if the antenna is an active indoor antenna

with a signal amplifier and it is not already

supplied with a voltage via a mains plug

(or similar supply). Otherwise you may

cause a short circuit and irreparably dam-

age your antenna.

note:

Additional operations are explained in the

following sections.

setting-all-analogue-television-

channels

Analogue channels are displayed in the channel

list after the digital channels.

Select the »Active Antenna Power«« with »

or » «. Switch on the antenna power supply

for the antenna with » « or » « (»On«).

v«

note:

Plug the rooftop antennacable (for analogue

Select » Digital Manual Tuning« with »

« and press »oK« to confirm.

– The menu appears.

v« or

television channels) into the »Ant-in«

socket on the television.

»Λ

Open the menu with »menu«.

Enter the channel number directly with

1-...-0« and press »oK« to confirm.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

–After the search is complete, the channels

found are displayed in the »Results« menu.

– The »SOURCE SETUP« menu appears.

Select the line »Source« with »v« or »

Press »menu« to finish the setting.

and press »oK« to confirm.

Select the option »Air« or »Cable« with » «,

» «, »

v« or »Λ

« and press »oK« to con-

firm.

Select the line »Automatic Channel Search«

with »

firm.

v« or »Λ« and press »oK« to con-

-56

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

20.09.2010

15:46

tuning-the-television-channels-by-

entering-the-channel-numbers

SOURECE SETUP

Open the menu with »menu«.

Source

Cabel

Select the line »SOURCE SETUP« with »

v«

Automativ Channel Search

Digital Manual Tuning

Analogue Manual Tuning

Program Table

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select the line » Analogue Manual Tuning«

with »

firm.

v« or »Λ« and press »oK« to con-

Signal Information

CA - Modul

– The menu appears.

Select the line »Program No« by pressing

v« or »Λ« and use » « or » « to save the

INSTALLATION

ANALOGUE MANUAL TUNING

Beenden

Zurück

Program No

TSystem

Band

Select the line »Country« with »v« or »Λ«

and press »oK« to confirm. In the country

selection menu, select the country with » «,

Channel

» «, »

« or »

Select the line »Scan Typ« with »

and set the option »ATV« with » « or » «.

« and press »oK« to confirm.

Fine Tuning

v« or »Λ«

48.25 MHz

Start the scan with » «-(red).



Auto Previous

Auto Next

Store

note:

After starting the scan, a security query will

preset.

appear. Press » « (green) to confirm the



option »Yes«.

Select »Band« by pressing »

v« or »Λ« and

– All channel and favourites lists for the ana-

logue channels will be deleted and com-

piled anew.

use »» « or » « to choose between »S«

(special channel) or »C« (normal channel).

Select the line »Channel« with » « or »

Λ«

– The »Results« menu appears, and the scan

for TV channels begins. Depending on the

number of television channels received,

this can easily take a few minutes.

– The search is complete as soon as the »PRO-

GRAM TABLE« appears.

and enter the channel number with » « or

» « step by step, or use »1…0« to enter it

directly.

notes:

The current system is displayed in the

»System« line. If the colour or sound is

not functioning properly, select the line

»System« with »

to select the preferred setting.

note:

You can abort the search by pressing

»menu«.

v« or »

«. Use » « or » «

Press »menu« to end the setting.

-57

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

If fine tuning is necessary, select the line

Changing-stored-analogue-

»Fine Tuning« with »

v« or »Λ« and use » «

-channels

or » « to make the setting.

If channels were stored with the automatic chan-

nel search while tuning the television channels,

you can delete them. You can also store chan-

nels in a different preset, change or enter the

name of a channel as well as skip channels.

Press »

« (blue) to save the setting.



note:

If you wish to remedy other television

channels, repeat steps 4 to 8.

8- Press »menu« to end the setting.

selecting-a-channel-list

note:

Analogue channels can be selected if the

option »Air« or »Cable« has been selected.

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

v«

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select the line »Program Table« with » « or

Λ« and press »oK« to confirm.

– The »PROGRAME TABLE« menu appears.

note:

Additional operations are explained in the

following sections.

Deleting-channels

In the »PROGRAME TABLE« menu, select the

television channel to be deleted with «,

«, » « or » « and press » «-(red) to con-

»v

firm.



Press » « (yellow) to confirm the deletion

process.



note:

« (blue) allows all television channels



to be deleted.

Press » « (green) to confirm the deletion



process.

-58

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

entering-channel-names-(8-digit-

maximum)

Creating-lists-of-favourites

You can select your favourite channels and

save them in up to four favourites lists (Fav 1 to

Fav 4).

In the »PROGRAME TABLE« menu, select the

television channel with » «, » «, » « or

» « and press » «-(red) to confirm.



In the »PROGRAME TABLE« menu, switch

over to the list view with » « (yellow).



Mark the television channel with »

(green).



Select the preferred channel with »

or »Λ«.

v«

Select the digits or letters with »Λ« or »v

and use » « or » « for the next position, and

Use » « or » « to ”push“ the channel into

repeat the entry.

one of the favourites lists 1 to 4 and press

»oK« to confirm.

Save the channel name with » « (green).



– The position in the favourites list is marked

with »✔«.

– You can enter the same channel in more

than one favourite list.

note:

If you wish to enter other channel names,

repeat steps 1 to 4.

– Each favourite list can store up to

255 channels.

skipping-television-channels

You can highlight television channels to be

skipped when you select with »Λ« or »v«.

Selection is still possible using the number

buttons.

note:

Channels can also be deleted from favour-

ites lists. Select the channel to be deleted

with »

v«, »Λ«, » « or » « and delete it with

In the »PROGRAMETABLE« menu, switch over

»oK«.

to the list view with » « (yellow).



exiting-the-settings

Select the preferred channel with »

or »Λ«.

v«

Press »menu« to end the setting.

Select the column »Skip« with » « or » «

and use »oK« to mark the channel.

– The channel is marked using »✔«.

note:

Channels can also be reactivated. Select the

channel with »v« or »Λ«, then select the

column »Skip« and reactivate the channel

with »oK«.

-59

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

inFormAtion_{----------------------------------------------------------------------------------------------------------------------}

Displaying-signal-information

(for digital channels only)

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

v«

Select the line »Signal Information« with

« or » « and press »oK« to confirm.

»v

– Information on the channel, network,

modulation, symbol rate, quality and

signal strength is displayed.

notes:

The signal information changes in accord-

ance with the current input source.

The signal properties are displayed in the

lower section of the menu. The further the

bars for »Quality« and »Signal Strenght«

extend to the right, the better the reception

signal.

The signal level not only depends on your

receiver system, but also on the channel

which is currently active. Remember this

when aligning your antenna based upon

the signal level display.

Press »menu« to close the menu.

-60

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

inFormAtion_{----------------------------------------------------------------------------------------------------------------------}

Constellation: 16QAM, 64QAM, QPSK

GrunDiG-hAmBurG-32-vlC-8140-s

Analogue-reception-ranges:

technical-data

C02 ... C80, special channels S01 ... S41

operating-voltage:-

preset-channels:-

220–240 V, , 50–60 Hz

TV/Radio

6000 (Satellite – DVB-S),

1000 (Cable – DVB-C) or

100 (Analogue)

power-consumption:

Operational 83 W

Standby <1,0 W

1000 (Terrestrial – DVB-T) or

100 (Analogue)

9 AV, 2 USB

energy-efficiency-class:

screen-(dm²):

maximum-power-consumption:

Operational 145 W

screen-size:

80 cm/32 inch

Annual-power-consumption:

121 kWh

maximum-resolution:

WUXGA, 1920 x 1080

Audio-output:-

2 x 20 W music power output

2 x 10 Sine wave power

weight:

approx. 11 kg

rohs-limits: Pb (Lead)/Hg (Mercury)

Pb meets ROHS directive / 56 mg

maße:

W H D 78,9 cm 51,8 cm 8,1 cm

peak-luminance-ratio:

% 65

Default-satellite:

lnB-power-supply:

13/18 V, 14/19 V optional, maximum 450 mA

lnB-switching-signal:

0/22 kHz 650mV +/- 250mVpp

DiseqC:

1.0-operation, 1.1-operation, 1.2-operation

Digital-reception-ranges:

satellite:

Ku band:

10,700 MHz – 12,750 MHz

Modulation: DVBS QPSK, DVBS2 QPSK,

8 PSK

IF band:

Signal level: -25dBm to -65 dBm

950 MHz – 2,150 MHz

Cable:

Overall band: 110 MHz – 862 MHz

Modulation:

16QAM, 32QAM, 64QAM,

128QAM and 256QAM

Symbol rate: 4.0 Msym/s to 7.0 Msym/s

terrestrial:

VHF/UHF band, Bandwidth 7 MHz

and 8 MHz

COFDM modi: 2k and 8k

Technical changes and errors reserved.

-61

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

inFormAtion_{----------------------------------------------------------------------------------------------------------------------}

service-information-for-retailers

Only operate the television

with the power supply/power

cord provided.

The product complies with the

following EU directives:

2006/95/EC directive on electrical equipment

for use within certain voltage limits.

2004/108/EC directive on electromagnetic

compatibility.

2009/125/EC directive on ecodesign require-

ments for energy-related products.

environmental-note

This product has been made

from high-quality parts and

materials which can be re-used

and recycled.

Therefore, do not dispose of the product along

with normal household waste at the end of its

service life. Take it to a collection point for the

recycling of electrical and electronic equipment.

Dispose of the used device at a collection point

for electrical and electronic equipment. The sym-

bol on the product, in the operating manual or

on the packaging indicates that recycling is pos-

sible.

Information on collection points is available from

your local authorities.

Help protect the environment by recycling used

products.

note:

This is a Class A product. During operation

the device could cause radio interference.

In this case the user may have to remedy

this. Please contact your specialist dealer.

-62

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

inFormAtion_{----------------------------------------------------------------------------------------------------------------------}

troubleshooting

If the information provided below does not help, please consult an authorised GRUNDIG dealer.

Please bear in mind that malfunctions can also be caused by external devices such as video recorders

or satellite receivers.

problem

possible-cause

remedy

Screen lit (snow), but no station

visible

Antenna cable

Is the antenna cable connected?

No TV channel tuned

Start a channel scan

Insuﬃcient contrast in picture

The picture settings are not correct

Adjust the brightness, contrast or colour

setting

Problem at station

Try another channel

Picture and/or sound distorted

Ghosting, reﬂection

Interference from other devices

Place the device in a diﬀerent position

Channel setting

Antenna

Automatic or manual tuning/ﬁne tuning

Have antenna cable or system checked

Turn up the colour

No colour

Colour intensity too low

Adjust TV standard (if setting option is

available)

Select the correct colour standard

Problem at station

Try a diﬀerent channel

Picture but no sound

Volume is set to a minimum

Turn up or switch on the volume

Teletext impaired or absent

Problem at station

Try a diﬀerent channel

Television channel (no teletext)

or antenna system

Try with a diﬀerent TV channel,

carry out ﬁne tuning

Station signal too weak

Check antenna

The remote control does

not work

Obstacle between remote control and

device.

Point remote control at television

Battery problem

Check batteries and replace if

necessary

Operating mode undeﬁned

Switch oﬀ the television at the mains

switch for two minutes

Picture too dark in PC mode

Incorrect setting for picture resolution

and picture frequency on the PC

Change settings on the PC

(e.g. 1280 x 768 resolution,

refresh rate 60 Hz)

-63

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Dust Collector G0548 User Manual
Grizzly Saw G0524 User Manual
Harrison Labs Music Mixer V202 User Manual
Hotpoint Cordless Telephone DDP 700 User Manual
Huawei Cell Phone M865 User Manual
Hubbell Electric Heater Company Water Heater EMV User Manual
Hunter Fan Outdoor Ceiling Fan 20177 User Manual
Hyundai Flat Panel Television E260D User Manual
IBM Laptop 04P4963 User Manual
Image Home Gym IMTL139050 User Manual