Instructions – Parts List
6:1 Fire–Ballr 425 Pump
308608K
For pumping non–corrosive and
non–abrasive oils and lubricants only.
Model 238108, Series D
1100 psi (7.6MPa, 76 bar) Maximum Working Pressure
180 psi (1.2 MPa, 12 bar) Maximum Air Input Pressure
Important Safety instructions
Read all warnings and instructions in this manual.
Save these instructions.
06031
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441
Copyright 1995, Graco Inc. is registered to I.S. EN ISO 9001
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
SKIN INJECTION HAZARD
Fluid from the dispensing valve, leaks or ruptured components can inject fluid into your body and
cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on
the skin can also cause serious injury.
D Fluid injected into the skin may look like just a cut, but it is a serious injury. Get immediate
surgical treatment.
D Do not point the dispensing valve at anyone or at any part of the body.
D Do not put your hand or fingers over the end of the dispensing valve.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Use only extensions and no-drip tips which are designed for use with your dispensing valve.
D Tighten all fluid connections before operating the equipment.
D Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do
not repair high pressure couplings; you must replace the entire hose.
HAZARDOUS FLUIDS
Improper handling of hazardous fluids or inhaling toxic fumes can cause extremely serious injury,
even death, due to splashing in the eyes, ingestion, or bodily contamination.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid
and solvent manufacturer.
308608K
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D Ground the equipment. Refer to Grounding on page 7.
D If there is any static sparking or you feel an electric shock while using this equipment, stop
dispensing immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being dispensed.
D Do not smoke in the dispensing area.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
D Keep clear of all moving parts when starting or operating the pump.
D Before servicing the equipment, follow the Pressure Relief Procedure on page 8 to prevent the
equipment from starting unexpectedly.
4
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The typical installation shown in Fig.1 is only a guide
CAUTION
Always mount the pump firmly to a bracket or a
tank cover. Never operate the pump while it is not
mounted. Such use could damage the pump and
fittings.
for selecting and installing a pump; it is not an actual
system design. Contact your Graco representative or
your Graco distributor for assistance in designing a
system to suit your needs.
G
N
D
A
A
C
A
R
J
K H
P
E
Z
B
Y
F
DETAIL A
L
TI0890
T
S
M
For Portable Applications
KEY
A
B
C
D
Bleed-type master air valve (required)
Air line filter
J
Dispensing valve (model 222411 shown)
K
L
M
N
P
R
S
T
Y
Z
Thermal relief kit (required), Part No. 240429
Male quick-disconnect fitting
Female quick-disconnect coupler
Air line lubricator
Air regulator and gauge
Pump runaway valve (shown for
position) – not needed if you use
a low level cut-off valve
Air inlet
Ball valve (for releasing collected moisture)
Pump
Drain valve (required)
Fluid hose
E
F
G
H
Electrically conductive air hose (218093 shown)
Fluid inlet
Wall-mounting bracket
Ground wire (required)
Muffler
05610
Fig. 1
308608K
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
1. Screw the muffler (5) into the 3/4-in. npt muffler
System Accessories
port, and tighten it using a wrench on the flats of
the muffler near the male threads.
CAUTION
2. Install an air line lubricator (N) for automatic air
motor lubrication.
Do not hang the air accessories directly on the air
inlet (E). The fittings are not strong enough to
support the accessories and may cause one or
more to break. Provide a bracket on which to
mount the accessories.
3. Install the air regulator (C) to control pump speed
and pressure.
4. Install an air line filter (B) to remove harmful dirt
and contaminants from your compressed air
supply.
NOTE: Install the accessories in the order shown in
Fig. 1.
5. Install a bleed-type master air valve (A) to isolate
the accessories for servicing. See Fig. 1. To
order a bleed-type master air valve, order Part No.
107142.
WARNING
Four accessories are required in your system: an
air shut-off valve/air bleed device, fluid drain valve,
thermal relief kit, and ground wire. These accesso-
ries help reduce the risk of serious bodily injury
including fluid injection, splashing in the eyes or on
the skin, injury from moving parts if you are adjust-
ing or repairing the pump, and explosion from
static sparking.
As an alternative to a bleed-type master air valve,
you can install an air line quick disconnect coupler
(M) and fitting (L) to serve as an air-bleed device.
See Detail A in Fig. 1.
6. Install a drain valve (H) near the pump fluid outlet
to relieve fluid pressure in the hoses and gun when
opened. To order a fluid drain valve, order Part
No. 210658.
The air bleed device relieves air trapped between it
and the air motor after the air supply is shut off.
Trapped air can cause the air motor to cycle unex-
pectedly, causing serious bodily injury if you are
adjusting or repairing the pump. Use either a
bleed-type master air valve (A) or a quick-discon-
nect coupler (M) and fitting (L). Install near the
pump air inlet, within easy reach of the pump.
7. Install a thermal relief kit (K) on the dispensing
valve side of the pump. To order a 1600 psi
(110 bar, 11 MPa) thermal relief kit, order Part No.
240429.
The fluid drain valve (H) assists in relieving fluid
pressure in the displacement pump, hoses and
dispensing valve. Triggering the valve to relieve
pressure may not be sufficient.
8. Install a suitable fluid hose (P) and dispensing
valve (J).
Cover Mount
For cover mounting, see the Mounting Hole Layout
on page 18.
The thermal relief kit assists in relieving pressure in
the pump, hose, and dispensing valve due to heat
expansion.
Wall Mount
The ground wire reduces the risk of static sparking.
The pump shown in Fig. 1 is wall mounted. To order
the wall-mounting bracket, order Part No. 238245.
6
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
To ground the pump, remove the ground screw (Z)
Grounding
and insert through the eye of the ring terminal at end of
the ground wire (Y). Fasten the ground screw back onto
the pump and tighten securely. Connect the other end of
the ground wire to a true earth ground. See Fig. 2. To
order a ground wire and clamp, order Part No. 222011.
Proper grounding is an essential part of maintaining a
safe system.
To reduce the risk of static sparking, ground the pump.
Check your local electrical code for detailed grounding
instructions for your area and type of equipment. Be
sure to ground this equipment:
1. Pump: Use a ground wire and clamp as shown in
Fig. 2.
2. Air and Fluid hoses: Use only electrically conduc-
tive hoses.
3. Air compressor: Follow manufacturer’s recom-
mendations.
Y
4. Fluid supply container: Follow the local code.
Z
5. To maintain grounding continuity when flushing or
relieving pressure, always hold a metal part of the
valve firmly to the side of a grounded metal pail,
then trigger the valve.
TI1052
Fig. 2
308608K
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Pressure Relief Procedure
WARNING
HAZARDOUS VAPORS
The air motor exhaust coming out of the
muffler could contain harmful materials,
such as oil, antifreeze, or some of the
material being pumped.
WARNING
SKIN INJECTION HAZARD
To reduce the risk of serious bodily
injury, including fluid injection or splash-
ing in the eyes or on the skin, always
follow this procedure whenever you shut off the
pump, when checking or servicing any part of the
system, when installing or changing dispensing
devices, and whenever you stop dispensing.
1. With the air regulator (C) closed, open the bleed-
type master air valves (A) or, if so equipped, join
the quick disconnect coupler (M) to the male fitting
(L).
1. Close the bleed-type master air valve (required in
your system).
2. Open the dispensing valve (J) into a grounded
metal waste container, making firm metal-to-metal
contact between the container and valve.
2. Hold a metal part of the dispensing valve firmly to
a grounded metal waste container and trigger the
valve to relieve the fluid pressure, or open the
drain valve (H).
3. Open the pump air regulator (C) slowly, just until
the pump is running. When the pump is primed
and all air has been pushed out of the lines, close
the dispensing valve.
If you suspect that the dispensing valve or hose is
completely clogged, or that pressure has not been fully
relieved after following the steps above, very slowly
loosen the hose end coupling and relieve pressure
gradually, then loosen completely, then clear the valve
or hose.
NOTE: When the pump is primed, and with sufficient
air supplied, the pump starts when the dis-
pensing valve is opened and shuts off when it
is closed.
4. If your system is equipped with a runaway valve (D
in Fig. 1), set it for your system configuration. See
manual 308201 for instructions on setting the
pump runaway valve.
Startup and Adjustment
WARNING
COMPONENT RUPTURE HAZARD
The maximum working pressure of each
component in the system may not be the
same. To reduce the risk of overpres-
5. Adjust the air regulator until you get sufficient flow
from the dispensing valve. Always run the pump
at the lowest speed necessary to get the desired
results. Do not exceed the maximum working
pressure of any component in the system.
surizing any component in the system, be sure you
know the maximum working pressure of each
component, including the air motor and pump.
Never exceed the maximum working pressure of
the lowest rated component in the system. Over-
pressurizing any component can result in rupture,
fire, explosion, property damage, and serious
injury.
6. If your pump accelerates quickly or is running too
fast, stop it immediately and check the fluid supply.
If the supply container is empty and air has been
pumped into the lines, prime the pump and lines
with fluid, or flush it and leave it filled with a com-
patible solvent. Be sure to eliminate all air from
the fluid lines. If your system has a runaway
valve, reset it according to the instructions in
manual 308201.
To determine the fluid output pressure using the air
regulator reading, multiply the ratio of the pump by
the air pressure shown on the regulator gauge. For
example:
6 (:1) ratio x 180 psi air =
1080 psi fluid output
CAUTION
Never allow the pump to run dry of the fluid being
pumped. A dry pump will quickly accelerate to a
high speed, possibly damaging itself, and it may
get very hot.
6 (:1) ratio x 7 bar air = 42 bar fluid output
6 (:1) ratio x 0.7 MPa air = 4.2 MPa fluid output
Limit the air to the pump so that no air line or fluid
line component or accessory is overpressurized.
8
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
7. Read and follow the instructions supplied with
8. If the pump will be unattended for any period of
time, if there is an air supply interruption, or to shut
off the system at the end of the work shift, always
relieve the pressure.
each component in your system.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
9. Check periodically to ensure that the pump’s
mounting is secure.
Troubleshooting
NOTE: Check all other possible problems and solu-
WARNING
SKIN INJECTION HAZARD
To reduce the risk of serious bodily
tions before disassembling the pump.
injury, including fluid injection or splash-
ing in the eyes or on the skin, always
follow the Pressure Relief Procedure on page 8
whenever you shut off the pump, when checking or
servicing any part of the system, when installing or
changing dispensing devices, and whenever you
stop dispensing.
Problem
Cause
Inadequate air supply pressure or
Solution
Pump fails to operate
Increase air supply; clear
restricted air lines
Closed or clogged dispensing
valve
Open; clear
Clear*
Clogged fluid lines, hoses, valves,
etc.
Damaged air motor
Service air motor
Exhausted fluid supply
Refill and reprime or flush
Service air motor
Continuous air exhaust
Erratic pump operation
Worn or damaged air motor gas-
ket, packing, seal, etc.
Exhausted fluid supply
Refill and reprime or flush
Clear; service
Held open or worn intake valve or
piston packings
Pump operates, but output low on
up stroke
Held open or worn piston packings
Clear; service
Pump operates, but output low on
down stroke
Held open or worn intake valve
Clear; service
Pump operates, but output low on
both strokes
Inadequate air supply pressure or
restricted air lines
Increase air supply; clear
Closed or clogged valves
Open; clear
Service
Fluid is coming out of the muffler.
Worn or damaged throat seal
* Follow the Pressure Relief Procedure on page 8 and disconnect the fluid line. If the pump starts when
the air is turned on again, the line, hose, valve, etc., is clogged.
308608K
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor and Throat Service
9. Remove the eight screws (3) holding the cylinder
Before You Start
(30) to the base (28). Carefully pull the cylinder
D Be sure you have all necessary parts on hand.
Air Motor Repair Kit 207385 includes repair parts
for the motor. Use all the parts in the kit for the
best results. Parts included in the kit are marked
with one asterisk, for example (19*), in the text and
drawings. See the Parts List on page17.
straight up off of the piston assembly (27).
CAUTION
To avoid damaging the cylinder wall, lift the cylinder
straight up off of the piston. Never tilt the cylinder
as it is being removed.
D Two accessory tools should be used: Padded
Pliers, 207579, are used to grip the trip rod without
damaging its surface, and a 0.125-in. (3.18 mm)
Gauge, 171818, is used to assure the proper
clearance between the poppets and seat of the
piston.
24
30
Disassembly
1. Flush the pump.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
31
27
2. Relieve the pressure.
3. Disconnect the hoses, remove the pump from its
mounting, and clamp the air motor base (28) in a
vise horizontally by closing the vice jaws on the
flange.
3
4. Use a strap wrench on the displacement pump
cylinder (110) to screw it out of the air motor base
(28). See Fig. 3.
29
28
10{
5. Remove the piston/valve seat (109) from the rod
(29) with wrenches or with the vice and a wrench.
103
113
108{
6. Remove the piston ball (103), u-cup packing
flange
(107{), and piston washer (113).
109
110
107{
105{
7. Remove the air motor base from the vice, and
place the piston rod (29) flats in the vice with the
air motor up.
8. Loosen the lift ring (24). Pull up the lift ring, grip
the trip rod (31) with the padded pliers, and screw
the lift ring off of the rod.
TI1076
06033
Fig. 3
CAUTION
Do not damage the plated surface of the trip rod
(31). Damaging the surface of the trip rod can
result in erratic air motor operation. Use the
special padded pliers, 207579, to grasp the rod.
{ Included in Pump Repair Kit 238225,
which may be purchased separately.
10
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor and Throat Service
10. Pull the piston assembly from the air motor base
15. In this step, while you are prying with the screw-
driver with one hand, cover the toggle assemblies
with your other hand so as to catch the spring-
loaded toggle assemblies when they snap out of
the lugs. Place the tip of a screwdriver into the
piston between the piston lugs (L) below the pivot
pins (16) on the toggles, pry up with the screw-
driver handle to compress the springs on the
toggle assembly (M) up and away from the piston
lugs, and remove the parts. See Fig. 4.
(28), and set it aside.
11. Remove the throat bearing (36) with a 2-in. socket,
remove the u-cup seal (10{), and wipe the seat
clean with a cloth.
12. Remove the piston/base from the vise, and set it
upright on the workbench.
16. Straighten the lockwires (22*) and remove them
from the valve nuts (21*). Screw the top nuts off.
Remove the trip rod yoke (13), actuator (12), and
trip rod (31). Unscrew the bottom nuts (21*), and
remove the poppets. Make sure the valve bar
spring clips (14) are not worn or damaged and that
they properly guide the actuator (12).
13. Inspect the air motor for damaged or worn inlet
valve grommets (17*), o-rings (19*, 20*), valve
nuts (21*), lock wires (22*), exhaust valve poppets
(26*), or inlet valve poppets (32*). If any of these
parts need to be replaced, continue with steps 14
to 20. Otherwise, see Reassembly on page 12.
17. Remove the exhaust valve poppets (26) by cutting
them with a side cutter, then pull them out of the
actuator (12).
14. Use a screwdriver to push down on the trip rod
yoke (13), and snap the toggles down. See Fig. 4.
18. Clean all the parts carefully in a compatible solvent
and inspect them for wear or damage. Use all the
repair kit parts during reassembly, and replace
other parts as necessary.
WARNING
MOVING PARTS HAZARD
To reduce the risk of pinching or
amputating your fingers, keep your
fingers clear of the toggle assemblies
when you are snapping the toggles
(M in Fig. 4 ) up or down.
19. Check the surfaces of the piston, piston rod, and
cylinder wall for scratches or wear. A scored rod
will cause premature packing wear and leaking.
20. Lubricate all parts with a light, waterproof grease.
308608K
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor and Throat Service
13
31
Cut off tops
of poppets as
indicated by
dotted lines.
15
23
25
16
15
22*
M
31
21*
32*
17*
13
26*
14
32*
21*
12
Turn
lock-
wires
up.
L
17*
21*
19*
32*
0.125”
(3.18 mm)
27
28
32*
27
04422
14
26* 21*
05612
Cutaway View
Fig. 4
Reassembly
1. Place the piston rod (29) flats in the vice with the
air motor up.
7. Measuring with the gauge (Part No.171818),
create 0.125-in. (3.18 mm) of clearance between
the inlet valve poppets (32*) and the piston seat
when the inlet valve is open. See the Cutaway
View Fig. 4.
2. Pull the exhaust valve poppets (26*) into the valve
actuator (12), and clip off the top parts of the
poppets (shown with dotted lines in the Cutaway
View in Fig. 4).
NOTE: Adjust the distance between the inlet valve
poppets and the piston seat by turning the
top valve nuts (21*).
3. Install the grommets (17*) in the actuator (12),
place the inlet valve poppets (32*) in the piston,
and thread the bottom valve nuts (21*) onto the
8. Tighten the bottom valve nuts (21*) securely by
hand.
inlet valve poppets until there are a few threads left
before the threads run out.
9. Align the holes in the valve nuts (21*) and the slots
on the tops of the inlet valve poppets (32*), and
drop the lock wires (22*) through the holes in the
valve nuts and into the slots in the inlet valve
poppets. Pull the lock wires down tightly, and
bend the ends with pliers so that they cannot be
pulled back out of the holes.
NOTE: If you thread the valve nuts too far down
onto the poppets, they will run off of the
threaded part of the poppets.
4. Grease heavily and place the trip rod (31) in the
piston, place the actuator (12) in the yoke (13),
and place the well-greased actuator/yoke assem-
bly in the piston, with the trip rod going through the
center holes of the actuator and yoke and the inlet
valve poppets (32*) going through the grommets
(17*).
CAUTION
Never re-use the old lock wires. They will get
brittle and break easily from too much bending.
5. Thread the top valve nuts (21*) onto the inlet valve
poppets (32*) until one thread of the inlet valve
poppets is exposed above the valve nuts.
10. Grease and install the new o-rings (19* and 20*)
on the piston assembly (27) and in the groove in
the air motor base (28).
6. Install the toggle pins (15) in the yoke (13), place
the toggle arm (23) ends of the toggle assembly
(M) onto the toggle pins, and snap the pivot pin
(16) ends of the toggle assembly into the lugs (L).
11. Clamp the air motor base (28) in a vise horizontally
by closing the vice jaws on the flange.
12
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor and Throat Service
12. Grease and reinstall the u-cup seal (10{), thread
16. Install the u-cup packing (107{) with the lips up,
and place the piston washer (113) on the piston/
valve seat (109). Make sure the lips of the u-cup
packing face up. See Fig. 3.
the throat bearing (36) into the air motor base (28),
and torque the throat bearing to 30 to 40 ft-lb
(41 to 54 N.m) using a 2-in. socket.
17. Place the piston ball (103) in the piston rod (29).
13. Slide the piston rod (29) down through the pack-
ing, and lower the piston assembly (27) into the air
motor base (28).
18. Clean the threads of the piston/valve seat, Apply
Loctiter to the threads, (109), and thread the
assembly from Step 16 onto the piston rod (29).
14. Carefully lower the cylinder (30) straight down onto
the piston assembly (27). Tighten the eight screws
(3) holding the cylinder to the base (28).
19. Clamp the flats of the piston/valve seat (109) in a
vice, and torque the piston rod (29) to the piston
valve seat to 40 to 60 ft-lb (54 to 81 N.m).
20. Clamp the air motor base (28) in a vise horizontally
by closing the vice jaws on the flange
CAUTION
To avoid damaging the cylinder wall, lower the
cylinder straight down onto the piston. Never tilt
the cylinder as it is being lowered.
21. Use a strap wrench to screw the displacement
pump cylinder (110) to the air motor base (28), and
torque to 95 to 105 ft-lb (129 to 142 N.m).
22. Before remounting the pump, connect an air hose
and run the air motor slowly, starting with just
enough air pressure to make the air motor run, and
make sure that it operates smoothly.
15. Grip the trip rod (31) with padded pliers, screw the
lift ring (24) onto the trip rod, push the lift ring
down, and screw it into the top of the cylinder.
23. Reconnect the ground wire before regular opera-
tion of the pump.
308608K
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Displacement Pump Service
Displacement Pump. See Fig 5.
Disassembly
NOTE: Clean and inspect all parts for wear or damage
as you disassemble them. Replace parts as
needed. For best results, always replace all
the o-rings and packings when you disassem-
ble the pump.
NOTE: Displacement Pump Repair Kit 238225
includes repair parts for the pump throat and
piston. Use all the parts in the kit for the best
results. Parts included in the kit are marked
with a dagger, for example (7{), in the text and
drawings. See the Parts List on page 15.
1. Relieve the pressure.
1. Flush the pump.
2. Follow steps 1 to 7 of Disassembly on page 10.
3. Carefully inspect the smooth inner surface of the
cylinder (110) for scoring or irregular surfaces.
Such damage causes premature seal wear and
leaking. Replace the cylinder as needed.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
Reassembly
Do steps 16 through 23 in Air Motor and Throat
Service on page 13.
2. Relieve the pressure.
3. Disconnect the hoses, remove the pump from its
mounting, and clamp the air motor base (28) in a
vise horizontally by closing the vice jaws on the
flange.
110
112
Intake Valve. See Fig 5.
1. Relieve the pressure.
104
105{
2. Unscrew the valve housing (111). Remove the
111
o-ring (105{), retainer (112), and ball (104).
05617
Fig. 5
{ Included in Pump Repair Kit 238225, which may
be purchased separately. The Parts List on page
15 includes all parts in kit.
3. Inspect the parts for wear or damage. If the ball is
nicked, replace it. Reassemble, using grease on
the male threads.
14
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
Displacement Pump Parts Drawing and List
Model 238108, Series D
Air motor not listed or shown here. See pages 16 and 17.
Ref
No.
Ref
No.
Part No. Description
Qty.
Part No. Description
Qty.
109
110
111
112
113
194016
190922
190926
190928
190924
PISTON
1
1
1
1
1
10{ 113345
SEAL, u-cup (shown on page 16) 1
CYLINDER, pump
VALVE HOUSING
RETAINER, ball
WASHER, piston
103
104
101190
101178
BALL, piston; metallic
BALL; sst
1
1
1
1
1
105{ 113347
107{ 113346
108{ 112349
PACKING, o-ring
PACKING, u-cup
PACKING, o-ring
{ Included in Pump Repair Kit 238225,
which may be purchased separately.
113
107{
3
103
109 1
108{
110
2
105{
112
104
111
1
1
2
3
Torque to 40 to 60 ft-lb (54 to 81 N.m)
Torque to 95 to 105 ft-lb (129 to 142 N.m)
Lips face up
03846
308608K
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor Parts Drawing
24
1
36
11
30
20*
10{
2
28
18
13
15
5
3
22*
21*
23
25
16
12
17*
21*
31
26*
7
27a
27b
27
27c
*19
See Displacement
Pump Parts Drawing
and List on page 15.
32*
29
06032
1
2
Torque to 30 to 40 ft-lb (41 to 54 N.m).
Lips must face down.
16
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor Parts List
Ref
No.
Ref
Part No. Description
Qty.
No.
Part No. Description
Qty.
24
25
26*
27
190929
167585
170709
207391
RING, lift
SPRING, helical compression
POPPET, exhaust valve
PISTON, includes items 27a to 27c
(also includes 207385 repair kit when
ordered as a replacement part)
SCREW, rd hd mach; 6–32 x 1/4” 2
CLIP, Spring
BARE PISTON (not sold separately) 1
BASE, air motor
ROD, piston
CYLINDER, air motor
ROD, trip
POPPET, inlet valve
LABEL, designation
LABEL, warning
BEARING, throat
1
2
2
3
5
7
101578
102656
116343
SCREW, cap, hex hd
8
1
1
1
1
1
1
2
2
2
1
1
1
4
2
2
MUFFLER, air exhaust
SCREW, ground
SEAL, u-cup
PACKING, o-ring
ACTUATOR, air valve
YOKE, trip rod
PIN, toggle
10{ 113345
11
12
13
15
16
17*
18
19*
20*
21*
22*
23
156698
158359
158360
158362
158364
158367
158377
158378
158379
160261
160618
160623
1
27a
27b
27c
28
29
30
31
32*
33
102975
158361
2
PIN, pivot
190927
193799
15E954
207150
236079
119344
1
1
1
1
2
1
1
1
GROMMET, inlet valve
PACKING, ring seal
PACKING, o-ring
PACKING, o-ring
NUT, valve
WIRE, lock
ARM, toggle
35Y 290259
36 190930
{ Included in Pump Repair Kit 238225,
which may be purchased separately.
*
Included in Air Motor Repair Kit 207385,
which may be purchased separately.
Y Extra warning labels are available at no cost.
308608K
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Mounting Hole
Layout
MODEL 238108 Pump, Series D
3.0-in. (76.2-mm)
diameter clearance
45_
hole
Four 1/4–20
UNC-2B tapped
depth 1.25-in
(31.7-mm) on
4.25-in (108-mm)
diameter bolt
circle
3/4-in.
npt fluid
outlet
1/2-in.
npt air
inlet
Four 0.406-in.
(10.3-mm)
diameter
holes on 7-in.
(177.8-mm)
diameter bolt
circle
26.4 in.
(670 mm)
3/4-in.
npt
muffler
port
8.0 in.
(203.2 mm)
diameter of flange
8.0 in.
(203 mm)
Note: For sealed
tank mounting,
use gasket
06031
192658.
Technical Data
Maximum working pressure . . . . . . . . . . . . . . . . . . . . . . . . 1100 psi (76 bar, 7.6 MPa)
Fluid pressure ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6:1
Air operating range . . . . . . . . . . . . . . . . . . 40 to 180 psi (3 to 12 bar, 0.3 to 1.2 MPa)
3
Air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ft /min per gallon pumped,
3
(0.051 m /min per liter pumped)
at 100 psi (7 bar, 0.7 MPa)
Pump cycles per gallon (liter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5 (3.8)
Maximum recommended pump speed . . . . . . . . 78 cycles/min; 6 gpm (23 liter/min)
Recommended speed for optimum pump life . . . . . . . . . . . . 15 to 25 cycles per min
Piston seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . polyurethane with nitrile spreader
Rod seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . polyurethane with nitrile spreader
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . aluminum, steel, polyurethane, nitrile
Approximate weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 lb (21 kg)
* Sound pressure level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79.5 dB(A)
* Sound pressure measured at 30 cycles per minute at 100 psi (7 bar, 0.7 MPa)
air inlet pressure per ISO Standard 3744.
Loctiter is a registered trademark of the Loctite Corporation.
18
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Charts
To find Fluid Outlet Pressure (psi/bar) at a specific fluid flow (gpm/lpm) and operating air pressure (psi/bar):
1. Locate desired fluid flow along bottom of chart.
2. Follow vertical line up to point of intersection with selected fluid outlet pressure curve.
2. Align point on curve with vertical scale on left side of chart to read fluid outlet pressure.
Test Conditions: Pump tested with AW-32 oil at 75_ F (24_ C)
Fluid Outlet Pressure
900
A 150 psi (10.3 bar) inlet air pressure
B 100 psi (6.9 bar) inlet air pressure
C 70 psi (4.8 bar) inlet air pressure
D 40 psi (2.8 bar) inlet air pressure
(62.1)
A
800
(55.2)
700
(48.3)
600
(41.4)
B
500
(34.5)
400
C
D
(27.6)
300
(20.7)
200
(13.8)
100
(6.90)
0
0
2
4
6
8
(7.57)
(15.14)
(22.71)
(30.28)
Fluid Flow – gpm (lpm)
3
To find Pump Air Consumption (scfm or m /min) at a specific fluid flow (gpm/lpm) and operating air pressure (bar/psi):
1. Locate desired fluid flow along bottom of chart.
2. Follow vertical line up to point of intersection with selected air consumption curve.
2. Align point on curve with vertical scale on left side of chart to read air consumption.
Test Conditions: Pump tested with AW-32 oil at 75_ F (24_ C)
Inlet Air Consumption
90
(2.52)
80
A 150 psi (10.3 bar) inlet air pressure
B 100 psi (6.9 bar) inlet air pressure
C 70 psi (4.8 bar) inlet air pressure
D 40 psi (2.8 bar) inlet air pressure
(2.24)
A
70
(1.96)
60
(1.68)
50
(1.40)
B
40
(1.12)
C
D
30
(0.84)
20
(0.56)
10
(0.28)
0
0
2
4
6
8
(7.57)
(15.14)
(22.71)
(30.28)
Fluid Flow – gpm (lpm)
308608K
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–533–9655 Toll Free
612–623–6928
612–378–3590 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 308608
Graco Headquarters: Minneapolis
International Offices: Belgium, Korea, China, Japan
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441
308608 10/1995, Revised 03/2007
20
308608K
Download from Www.Somanuals.com. All Manuals Search And Download.
|