MARQUIS 9000MWD
SINGLE LINE CORDLESS
HOTEL TELEPHONE
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
To reduce the risk of fire or injury, read and follow these instructions:
1. Use only the designated battery pack for cordless handset and power adapter for the base.
2. Do not dispose of the battery(ies)in a fire. The cell may explode. Check with the local codes for
possible special disposal instructions.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
4. Exercise care in handling batteries in order not to short the battery with conducting materials such as
rings, bracelets and keys. The battery or conductor may overheat and cause burns.
5. Do not attempt to recharge the battery(ies) provided with or identified for use with this product. The
batteries may leak corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the battery(ies) provided with or identified for use with this product by
heating them. Sudden release of the battery electrolyte may occur causing burns or irritation to the eyes
or skin.
7. When replacing the batteries, all batteries should be replaced at the same time. Mixing fresh and
discharged batteries could increase internal cell pressure and rupture the discharged battery(ies).
(Applies to products employing more than one separately replaceable primary battery).
8. When inserting batteries into this product, the proper polarity or direction must be observed. Reverse
insertion of batteries can cause charging, and that may result in leakage or explosion (applies to product
employing more than one separately replaceable primary battery).
9. Remove the batteries from this product if the product will not be used for a long period of time (several
months or more) since during this time the battery could leak in the product.
10. Discard dead batteries as soon as possible since dead batteries are more likely to leak in a product.
11. Do not store this product, or the batteries provide with or identified for use with this product in h i g h
temperature areas. Batteries that are stored in a freezer or refrigerator for the purpose of extending the
shelf life should be protected from condensation during storage and defrosting. Batteries should be
stabilized at room temperature prior to use after cold storage.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from overheating, these
openings must not be blocked or covered. The openings should never be blocked by placing the product on the bed, sofa,
rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation unless proper ventilation is provided.
IF UNIT IS EQUIPPED WITH POWER ADAPTER:
7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your dealer or local power company.
IF ADAPTER IS PROVIDED WITH A GROUNDED TYPE ATTACHMENT PLUG:
8. This product is equipped with a three wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.
IF ADAPTER IS PROVIDED WITH A POLARIZED ATTACHMENT PLUG:
This product is equipped with a polarized line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to inset the plug fully into the outlet, try reversing the
plug. If the plug should still not fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
9. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it.
10. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
11. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short
out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.
12. To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified serviceman when some
service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks.
Incorrect re-assembly can cause electric shock when the appliance is subsequently used.
13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those controls, that
are covered by the operating instructions because improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
14. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical
shock from lightning.
15. Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Part 15 Compliance
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for
Class B digital device, pursuant to Part 15 of the FCC Rules, These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and, can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio TV technician for help.
Canadian Emissions Compliance
"This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference Regulations of
the Canadian Department of Communications. "
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DOC - NOTICE AND LOAD NUMBER STATEMENT
NOTICE: The Canadian Department of Communications label identifies certified equipment. This
certification means that the equipment meets certain telecommunications network protective, operational
and safety requirements. The Department does not guarantee the equipment will operate to the user's
satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of
the local telecommunications company. The equipment must also be installed using an acceptable method
of connection. In some cases, the company's inside wiring associated with a single line individual service
may be extended by means of a certified connector assembly (telephone extension cord). The customer
should be aware that compliance with the above conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated
by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,
may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate
electric inspection authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be
connected to a telephone loop, which is used by the device, to prevent overloading. The termination on a
loop may consist of any combination of devices subject only to the requirement that the total of the Load
Numbers of all the devices does not exceed 100. An alphabetic suffix is also specified in the Load Number
for the appropriate ringing type (A or B), if applicable. For example, LN = 20 A designates a Load Number
of 20 and an "A" type ringer.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTIFICATION TO THE TELEPHONE COMPANY
Before you may connect your telephone you must notify the telephone company of particular
line(s) to which such connections is to be made, and provided to the telephone company the
FCC registration number and ringer equivalence number of the registered protective circuitry.
The customer shall give notice to the telephone company upon final disconnection of such
equipment or circuitry from the particular line(s).
MALFUNCTION OF TELEPHONE
In the event that your telephone fails to work properly during your ownership and use of it,
you should disconnect it from the telephone line to determine if it is your phone, which is not
working properly, or if it is problem in the telephone company's network. If the problem is
with your telephone you should discontinue its use until it is repaired.
TELEPHONE CONNECTION REQUIREMENTS
Except for telephone company- provided ringers, all connections to the telephone network
shall be made through standard telephone company provided jacks, in such a manner to allow
for easy and immediate disconnection of the terminal equipment. Standard jacks shall be so
arranged that if the plug connected thereto is withdrawn, no interference to the operation of the
equipment at the customer's premises which remains connected to the telephone net work shall
occur by reason of such withdrawal. These telephones may not be used on party lines or coin
operated lines.
CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES
The telephone company is entitled to make changes in its facilities equipment, operations, and
procedures. Should these changes be expected to render your terminal equipment incompatible
with the telephone company's facilities you will be given sufficient notice to allow you to
make the necessary modification to your terminal equipment without any interruption of your
service.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Information:
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bot-
tom of this equipment is a label that contains, among other information, a product identifier in the format
US:2N3WI29B95339 If requested, this number must be provided to the telephone company.
An applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i.e.,
RJ11C) in the packaging with each piece of approved terminal equipment.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modu-
lar plug is provided with this product. It is designed to be connected to a compatible modular jack that is also com-
pliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs
on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas,
the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a
line, as determined by the total RENs, contact the local telephone company. [For products approved after July 23,
2001, the REN for this product is part of the product identifier that has the format US:2N3WI29B95339 The digits
represented by 29 are the REN without a decimal point (e.g., 29 is a REN of 2.9). For earlier products, the REN is
separately shown on the label.]
If this equipment 95339/953391 causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the tele-
phone company will notify the customer as soon as possible. Also, you will be advised of your right to file a com-
plaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect
the operation of the equipment. If this happens the telephone company will provide advance notice in order for
you to make necessary modifications to maintain uninterrupted service.
Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternate or re-
pair any parts of device except specified.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service
commission or corporation commission for information.
This equipment is hearing aid compatible.
NOTICE: If your home has specially wired alarm equipment connected to the telephone line, ensure the installa-
tion of this [equipment ID] does not disable your alarm equipment. If you have questions about what will disable
alarm equipment, consult your telephone company or a qualified installer.
Should you experience trouble with this equipment, please contact (TeleMatrix, Inc.Customer Care Center 5025
Galley Road Colorado Springs, CO. 80915 . Toll Free:1-800-462-9446 Direct:719-638-8821 Fax:719-638-8815
www.telematrixusa.com) for repair or warranty information. If the equipment is causing harm to the telephone net-
work, the telephone company may request that you disconnect the equipment until the problem is resolved.
[NOTICE: According to telephone company reports, AC electrical surges, typically resulting from
lightning strikes, are very destructive to telephone equipment connected to AC power sources. To
minimize damage from these types of surges, a surge arrestor is recommended.]
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Features .........................................................…………………........................
Controls .............…..............…………………..................................................
8
9
Installation …………………............................................................................. 15
Wall Mounting .....…..............................................…………………................ 16
Battery Preparation ......................………………….......................................... 17
Switch Settings .…………………..…............................................................... 21
Programming ..........….........................................………………….................. 22
Operation .................…........................................................…………………. 25
Service ......................…........................................…………………................ 33
Warranty .....................…............………………….......................................... 34
Spare Part List ……………………………………………...………………… 35
9
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
One Line Operation
Cordless Handset, 900 Mhz Operation, with Handshake Technology
Long Life Rechargeable NiCd Battery
Speakerphone with volume control
10 Guest Service Keys (Speed Dial Locations)
TouchLiteTM Message Waiting Indicator/Retrieval Feature
Convenient Data Port
“Soft-Key” Volume Control (Handset -- 8 step/ADA Compliant)
HI/Low Ringer Volume Controls (Handset)
Speaker Volume Control Rocker Switch
Line Status Indicators (In-Use/Hold/Mute/Ringing)
Mute Key (Base)
Redial/Pause Key (submerged)
Flash Key (submerged)
Handset Locator Key (On Base)
Charge Light Indicator
Extended Memory Back-up (Lithium Battery)
Desk Or Wall Mountable
Operates Behind 24/48 Volt Systems
Hearing Aid Compatible
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP VIEW
(14)
(13)
(11)
(10)
(1)
NEON LED
STORE
FLASH
(12)
(9)
FOR MESSAGES
1
2
3
ABC
DEF
PRESS HERE
REDIAL
4
5
6
(8)
(7)
(6)
(3)
JKL
MNO
GHI
7
8
9
PQRS
WXYZ
TUV
*
0
#
SPEAKER
MUTE
(5)
(4)
(2)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE UNIT
1. Handset ..........……………………..….....…...…... Hearing aid compatible, low profile styling.
2. Charge LED …….………………………………..
3. In-Use / Ringer Indicator ………………………...
Indicator that lights when the handset is charging.
Indicator shows line ringing, line in use
4. Mute Key ………………………………………… Used to mute base micphone. LED indicator shows
when Mute is in use.
5. Speaker Key ……………………………………… Used to activate speaker mode. LED indicator shows
when Speaker is in use.
6. Speakerphone Volume Control Rocker Switch ….. Used to control the loudness of the speakerphone.
7. Locate Key ………………………...……………... Used to locate the handset unit.
8. Pause/Redial Key ....………..........………….….… Submerged key used to program pause into speed dial
memory or used to dial the last number dialed
9. TouchLiteTM One Touch Message Retrieval Key…
Combination visual message waiting lamp & speed dial
key used for message retrieval. LED indicator will blink
indicating a new message in the user’s voice mail box
(user must subscribe to a messaging system).
10. Flash Key ........…….…...............…………………. Submerged key used to program a flash timing into
speed dial memory.
11. Store Key ...……….………….......….................…. Submerged key used to program speed dial keys.
12. Guest Service Keys (Speed Dial) ……………….… 10 programmable speed dial keys used for one-touch
access to hotel guest services.
13. Neon 90V / LED Switch …………………………. Used to select 90 Volt Neon or low voltage LED
operation for Message Waiting.
14. Antenna …………………………………………... Used to communicate with the handset.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP VIEW OF HANDSET
(10)
(1)
(2)
(3)
(8)
ON/OFF HOLD
1
2
3
DEF
ABC
4
5
6
JKL
GHI
MNO
7
8
9
TUV
WXYZ
PQRS
(4)
0
#
*
(5)
FLASH
VOLUME
REDIAL
(7)
(6)
(9)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDSET UNIT
1. Handset ..........…………...........…………….... Hearing aid compatible, low profile styling.
2. ON/OFF Line Key ...............……………..…... Used to activate line or hold.
3. Hold Key ........................……………......…... Used to place call on hold.
4. Numeric Dialing Keypad ……………………. Used to dial numbers.
5. Redial Key ………………………….……….. Used to dial the last number dialed.
6. Handset Volume Control ………………….… Used to increase or decrease volume
7. Flash Key ........………............…………….... Provides a 600mS timed line break.
8. Handset Ringer HI/LOW Control Switch …... Used to control the loudness of the handset
ring.
9. Handset to Base Connection ………………..... Charges the battery when placed into the
cradle and connected to the base.
10. Antenna …………………………………………... Used to communicate with the base unit.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP SIDE
(1)
LEFT SIDE
(2)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Telephone Jack …………......................
2. Data Port …………..………........…......
Modular receptacle for plugging
in telephone line.
Convenient port to connect a computer
modem, fax or answering device.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
•
•
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
•
•
Never touch uninstalled telephone wires or terminals unless the telephone line
has been disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Parts Check List
5
1
The following parts are included with
the 9000MWD:
L
I
N
E
NEO
N
LED
STOR
FLASH
2
3
1. Stationary Base Unit.
2. Mobile Handset Unit.
3. 15’ Modular Telephone Line Cord.
4. 15’ Modular Line Cord
5. Handset Battery Pack.
6. Power Adapter.
F
OR M
E
S
S
A
G E
S
1
2
3
ABC
DEF
P
RESS
HER
E
4
5
6
JKL
MN O
GHI
RE
D
IA
L
7
8
9
PQRS
TUV
WXY
Z
*
0
#
OPER
S
PEAK
E
R
M
UTE
6
4
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Mounting Your Telephone*
The 9000MWD is designed to be conveniently
wall mounted.
Note: A 9000MWD wall mounting
kit must be used (not included)
Follow these easy steps:
1. The handset retaining clip must be
engaged to secure the handset when
hanging up. To engage the clip,
unsnap the clip, rotate the clip 180º
and then snap the clip into place.
2. A separate wall mount wedge kit is
needed for this installation. This
wedge will allow the telephone to be
at the correct angle when wall
mounted. To install the wedge for
wall mounting, snap into place.
* The wall mount wedge can be
ordered separately. See the Parts
List in the back of this manual.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Adapter “LINE” Connection
The power adapter “LINE” connection is
used to connect the telephone lines from
the wall jack to the telephone.
P
H
O
N
E
L
I
N
E
Using the 15’ modular telephone line cord
provided, connect one end of the cord to
the RJ14 telephone jack on the wall or
base board. The remaining end of the
cord plugs into the “L1+L2” jack side of
the power adapter.
Power Adapter “PHONE” Connection
The power adapter “PHONE” connection is
used to provide both the telephone line and
the power source to the telephone.
P
H
O
N
E
Using the 15’ modular telephone line cord
provided, plug one end of the line cord into
the back of the telephone. Plug the remain-
ing end into the power adapter jack labeled
“PHONE”.
120V AC Power
IMPORTANT!
The telephone will not function if the line cord connections are not properly inserted into the cor-
rect jack. Be sure that the telephone line cord connections are not reversed. (“LINE”/”PHONE”).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the Handset Battery
To install the handset battery;
1. Open the battery cover as shown,
2. Insert the battery pack. Match the polarity
marks from the battery to the case (+ to
+).
Battery Cover
Removal
2. Grip Here
3. When properly installed, the battery will
slide into position. DO NOT FORCE THE
BATTERY. Be sure the contacts are cen-
tered and the battery tab is placed into the
tab slot. Note: if the battery does not
seem to fit, turn the battery on the oppo-
site side and re-insert.
4. Replace the battery cover by inserting the
open end of the cover into the handset and
pressing the back into place.
3. Press Down
Center
4. Slide Downward
1. Insert small screw-
driver and lift upward
to release cover
Removing the Handset Battery and
Battery Cover
Battery Placement Tab Must Be
Placed Into Housing Slot
1. Insert a small screwdriver into bottom
slot. Lift the cover by lifting the screw-
driver. Do not lift the cover more that
1/2”.
2. Grip the handset tightly on the sides.
3. Depress the cover where the top portion
of the battery cover (middle of the hand-
set base) meets the handset. This will re-
lease the battery cover lock.
DO NOT LIFT MORE THAN 1.2” UPWARD
4. Slide the cover downward and remove.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Message Waiting Lamp
The 9000MWD supports a low-voltage LED
message waiting lamp or 90VDC neon.
To turn ON, slide the switch to the “LED” or
“NEON” position. The switch is located
underneath the overlay and faceplate on the top
of the base.
Note: The 9000MWD is factory preset to
the “Neon” setting.
*NOTE: Voice Mail will ONLY operate if
you subscribe to your local telephone
company voice mail service and/or if your
PBX telephone system is equipped with
this technology. These telephone features
will not work unless you are a subscriber.
!
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Guest Service Keys
(Speed Dial Memory)
The 9000MWD has 10 one-touch speed dial
memory locations that are used as a conven-
ience for dialing frequently used numbers.
Each speed dial memory location can store up
to 32 digits.
Step:
1.
Procedure:
Press the Speakerphone ON/OFF key to activate
the phone.
2.
3.
4.
Locate the Store key under the plastic overlay on
the top housing. Press the “Store” key.
Dial the digits using the numeric dial pad
(example: 1 2 3 4 5 6).
Note:
Press the desired speed dial location (1 through 5
or 10, plus the message waiting lamp) where the
memory is to be saved.
To program Speed Dial into the tele-
phones memory, the line cord must
be plugged into the power adapter
and the telephone line cord must be
plugged into the wall jack. The
Speaker key must be activated.
____________________________________________
To program additional numbers, repeat steps 3 thru 4.
____________________________________________
22
Download from Www.Somanuals.com. All Manuals Search And Download.
The TouchLiteTM Feature
TouchLiteTM is a patent-pending new innova-
tion that integrates the visual message waiting
lamp and a speed dial memory key into one
function. It allows easy-access for guests to
retrieve voice mail or front desk messages.
When the red message waiting lamp lights to
notify a guest that a message is waiting, a
simple press of the red TouchLiteTM connects
the guest to the message center or the front
desk.
Note: The TouchLiteTM key adds an additional
memory location to your 9000MWD telephone.
Programming The TouchLiteTM
See “Programming: Guest Service Keys
(speed dial memory)”
*NOTE: Voice Mail will ONLY operate if
you subscribe to your local telephone
company voice mail system and/or if your
PBX telephone system is equipped with
this technology. These telephone features
will not work unless you are a subscriber.
!
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming A Flash Into Memory
The “Flash” key is a storable function into
memory that is used to provide a 600mS timed
line break. This function may be required for
accessing line features provided by your
telephone system or local telephone company.
For example, many times the “Flash” is used
to access line features such as “call waiting”,
“call transfer”, “Call pick-up”, etc. Contact
your system coordinator or local telephone
company regarding special line features that
you may have where a Flash key is needed.
Note: the “Flash” function counts as 1 digit
when stored into a speed dial memory location
Programming A Pause Into Memory
The “Pause” key is used to program a 3
second delay into memory. A speed dial
number may need to pause during its dialing
sequence to insure proper connections. For
example, some telephone systems require that
a ‘9’ be dialed to access an outside telephone
line. In this case, a pause should be stored
after the digit ‘9’ for timing purposes.
When in the store mode, press the REDIAL/
PAUSE key (submerged) to store a pause into
the program memory.
Note: the “Pause” function counts as 1 digit
when stored into a speed dial memory location
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing A Call Using The Handset
Follow the instructions below for placing a call
using the handset.
1.
2.
Lift the handset from the base and press
the ON/OFF key to activate the line.
Dial out by using the numeric dial pad
on the handset. To reach guest services,
line one on handset can be activate.
Press the speed dial key on the base
unit.
3.
To end the call, simply replace the
handset back on the cradle, or press the
line key again.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE UNIT DIALING
Placing A Call Using The Base Unit
Follow the instructions below for placing a
call using the base unit.
1. The handset can either be on or off the
base cradle when dialing from the base
unit.
2. Press the SPEAKER key to activate.
3. Dial out by using the numeric dial pad on
the base unit.
4. To end the call, simply press the Speaker
key.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating The Handset
The 9000MWD is equipped with a
handset locator feature key located on
the base.
Simply press the “LOCATE” button
on the base unit. The handset will
beep for about 15 seconds. Once the
handset is located, simply press the
ON/OFF key to activate your handset.
Technology Feature:
Frequency Range Limitation
The 9000MWD cordless phone comes with
a special Frequency Range Limitation of
200 feet within the design of the phone. This
feature is designed specifically the hotel and
lodging industry to provide
clarity and security.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Handset
Volume Control
A convenient handset volume control is
provided. This volume control will adjust
the loudness of the handset. The loudness
can be adjusted in seven (8) steps up or
down.
Using The Speakerphone
Volume Control
A rocker volume switch is provided to
adjust the loudness of the speakerphone.
Simply press the upper part of the rocker
switch to increase the volume or press the
lower part of the rocker switch to lower
the volume. The loudness can be adjusted
in eight (8) steps up or down.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Line Status Indicators
(Base Unit)
Line Status Indicators
(Handset Unit)
The 9000MWD has visual LED indicators
located on the base unit that indicates the
status of the telephone.
The 9000MWD has visual LED indicators
located on the handset that indicates the
status of the telephone.
Ringing of Line
The LED above the line key blinks rapidly
RED to show ring.
Ringing of Line
The in use LED blinks rapidly GREEN to
show ring.
Line In-Use
The LED above the line key shows a
steady RED color when off-hook.
Line In-Use
The in use LED shows a steady GREEN
color when base in off-hook. When hand-
set in use , the in use in use LED on the
base unit blink slowly.
Line Mute
The LED above the MUTE key is a steady
RED when the “Mute” key is active.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Data Port
The 9000MWD is equipped with a convenient
port on the right side of the base unit. This
modular receptacle is used to plug in any
standard telephone device such as a computer
modem, answering machine or fax machine.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Hold Feature (on Handset)
The “Hold” key is used to place a caller on
hold. To use, simply press the “Hold” key on
the handset. The LED light on the handset
will indicate that the line is on hold and the
base unit LED will blink rapidly Green.
When placing a caller on hold, the line will
not be disconnected. To return to the caller,
press the “ON/OFF” key on the handset or
the “SPEAKER” key on the base.
Note: Pressing the SPEAKER key on the base when the
handset is on hold will activate the base unit. The hand-
set will stay on hold until released.
Using The Mute Feature
A “Mute” key is provided to allow for
privacy during a background conversation.
When the “Mute” key is activated, the
microphone in the speakerphone within
the base becomes disabled. When the
“Mute” feature is activated, the caller will
not hear your voice. The “Mute” key will
illuminate to show that the feature is acti-
vated.
To de-activate, press the “Mute” key again.
The MUTE feature only works on the base unit. The
handset does not mute out when MUTE is active.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Redial (On Handset)
The “Redial” key is used to automatically
redial the last number that was manually
dialed from the numeric dial pad of the spe-
cific handset or base unit.
To use (handset):
•
•
•
•
Lift the handset
Press ON/OFF key.
Press the “Redial” key.
The number that was last dialed on the
handset will automatically redial.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
When problems arise during installation or service that cannot be
resolved using this or related documents, contact the TeleMatrix
Technical Service department 8:30a.m. - 4:30p.m. MST:
Toll Free: 1-800-462-9446
Direct:
Fax:
719-638-8821
719-638-8815
Many times a problem is either installation or user related. Please
contact TeleMatrix PRIOR to sending a telephone to our service
center for repair. In the unlikely event that a factory repair be
necessary:
1. Include a brief description of the trouble that you are
experiencing.
2. Include a proof of purchase for a repair under warranty.
3. Send the telephone freight prepaid by UPS or Parcel Post
insured to:
TeleMatrix
Repair Center
5025 Galley Road
Colorado Springs, CO. 80915
TeleMatrix will pay to return the repaired telephone to you. Allow
2-3 weeks for delivery.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
STATEMENT OF LIMITED WARRANTY
TeleMatrix, Inc. and TeleMatrix Equipment, LLC (TMX) warrants to its [original end customer] [purchaser]
that Spectrum, Spectrum Plus and Marquis branded products manufactured by TMX are free from defects in
materials and workmanship for five (5) years after the date of purchase, and Regency branded products
manufactured by TMX are free from defects in materials and workmanship for three (3) years, other than the
following products for which the warranty period shall be one (1) year: handset batteries, either NiCd or NiMH,
used in TMX cordless products. If a product fails this warranty during the warranty period, TMX will, at its
option, either repair or replace the defective product or parts, or deliver replacements for defective products or
parts on an exchange basis at no additional charge to the customer except as set forth below. Repair parts or
replacement products may be either new or reconditioned. Products or parts returned to TMX under this war-
ranty will become the property of TMX. Warranties on products repaired by TMX expire at the
tion of the original warranty period.
termina-
This limited warranty does not cover:
1.
2.
3.
Products or parts which are damaged, abused or misused;
Any damage resulting from improper installation, maintenance or operation of the product;
Damage resulting from unauthorized modification or repair of the product, or from improper
connection of the product to other equipment;
4.
5.
6.
Cords, connectors and replaceable batteries;
Damage in transit to the TMX repair facility;
Any product or part unless proof of date of purchase is submitted with the product when returned for
warranty repair; or
7.
8.
Costs incurred by the customer in removing and shipping the product to TMX for repair or
replacement, and costs of reinstallation of the product.
Products or parts which are not owned and used by the original end user customer.
The cost and risk of loss or damage for sending the product to TMX will be borne by the customer.
TMX EXPRESSLY DISCLAIMS ALL WARRANTIES EXCEPT THE LIMITED WARRANTY SET
FORTH HEREIN, WHICH IS THE SOLE AND EXCLUSIVE WARRANTY OF THE PRODUCT, AND IS
IN LIEU OF ALL OTHER WARRANTIES, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED,
OR STATUTORY. THERE ARE NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR
A
PARTICULAR PURPOSE.
THE CUSTOMER’S SOLE REMEDY UNDER THE TMX
WARRANTY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE. IN NO EVENT WILL
TMX BE LIABLE TO CUSTOMER OR ANY OTHER PARTY FOR ANY INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT LIMITATION, DAMAGES OF LOST
PROFITS, LOST REVENUES, LOSS OF USE OF FACILITIES OR EQUIPMENT, OR COST OF
SUBSTITUTE EQUIPMENT ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT,
EVEN IF THE CUSTOMER HAS ADVISED TMX OF THE POSSIBILITY OF SUCH DAMAGES. TMX
LIABILITY FOR DAMAGES SHALL NOT EXCEED THE PURCHASE PRICE OF THE DEFECTIVE
PRODUCT.
This limited warranty is non-transferable without the prior written approval of TMX. It gives the customer
specific legal rights. The customer may have other rights which vary under local law. Some jurisdictions may
not allow limitations on the term of an implied warranty or exclusions or limitations of incidental or
consequential damages.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare Parts List
The following 9000MW accessories and spare parts
are available from TeleMatrix or Associate Distributors.
Part
List
Description
Number
Price*
$59.00
$59.00
$15.00
$15.00
$15.00
$8.00
Complete Handset Unit (light ash)
Complete Handset Unit. (black)
Handset Battery Pack—NiCd
12V DC Power Supply Adapter (light ash)
12V DC Power Supply Adapter (black)
15’ Modular Line Cord.(light ash)
15’ Modular Line Cord.(black)
Wall Mount Kit
22098-ASH
220981-BLK
11004
36002-ASH
360021-BLK
17301-ASH
173011-BLK
$8.00
$5.00
*Pricing in USD$ Currency. Freight is Prepay and Add.
Note:
To Place An Order
1. Contact TeleMatrix Customer Service department 8:30a.m. - 4:30p.m. MST
2. Or visit our web site for ordering information and local distributors.
Toll Free: 1-800-462-9446
Direct:
Fax:
719-638-8821
719-638-8815
Version 5.0
35
Download from Www.Somanuals.com. All Manuals Search And Download.
|