MONITORING
SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
matically mute all HRM-16 sends except the
channel D stereo and talkback outputs. This
unique feature allows each musician to hear a
rough or final mix and send soloed tracks from
the mix console. This eliminates the need for
musicians to relocate to the control room or
manually change their HRM-16 level settings.
normally located near the main mixing console,
provides the power and signal conditioning
for a maximum of eight HRM-16’s. Individual
channel sends from the console connect to the
HDS-16 inputs.
Note: Both the solo function on the HDS-16 and
the talkback system on the HRM-16 can be acti-
vated manually using their front panel controls or
by optional remote switches.
The front panel serves as the patch bay for all
input connections: eight mono and four stereo
¼-inch and TT input connectors. All connec-
tors are balanced and use the Tip/Ring/Sleeve
(TRS) wiring convention. Both ¼-inch and TT
connectors can be used but not for the same
channel. If both connector types are used for
the same channel, the TT connector will be ac-
ADDITIONAL USEFUL HRM-16
FEATURES INCLUDE
■
■
■
■
local effects send and return;
line out (mono);
tive and ¼-inch connector will be disabled.
bass and treble shelving EQ controls;
talkback level and master volume controls.
TALKBACK
Figure 2 shows the TALKBACK connectors at
the far left of the front panel. Connect the mix
console’s line-level, talkback-microphone out-
put or cue send to the HDS-16’s ¼-inch INPUT
jack. This signal is distributed to the HRM-16s
on the Centronics cable along with the other
channels. Use the RETURN FROM HRM-16
connector to monitor talkback from the HRM-
The HDS-16, a 2-U rack-mountable device
Figure 1: HDS-16 front panel
The front panel is shown above; the TT and ¼-inch input sections are shown in detail in Figure 2
and Figure 4, respectively. Note: Although the POWER indicator LED is located on the far right
of the HDS-16 front panel, the AC power ON/OFF switch is on the rear panel.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
16’s. Talkback is always available from the mix
console and the level can be adjusted with the
HRM-16’s TALKBACK VOLUME control.
There are two talkback modes designed for
live and studio situations:
LIVE/STAGE MODE (DEFAULT)
This mode establishes communication from the
HDS-16 to all HRM-16’s but not between them.
Each HRM-16 user must depress their TALK
button or switch to speak with the HDS-16 but
can always receive from it. The HRM-16 users
will not hear other HRM-16 users or their own
voice. This is useful for live situations where
a single HRM-16 user’s communication with
the mix engineer does not require interaction
between musicians. Live/Stage was selected
as the default mode to eliminate feedback from
adjacent stage monitors.
This mode establishes communication among
all HRM-16’s and the HDS-16 much like an
intercom system. Any HRM-16 user with their
TALK button depressed can speak to all HRM-
16’s and the HDS-16. Each person will also
hear their own voice.This mode is useful to
enable discussion between the musicians and
mix engineer between takes.
Figure 2: Detail of HDS-16 front panel: Talkback and TT inputs
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
Figure 3: Changing the talkback mode inside the HDS-16
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
level controls. The HDS-16 solo feature re-
CHANGING THE TALKBACK MODE
quires patching the mix console’s main or mix
A jumper located inside the HDS-16 selects
output to the HDS-16’s channel D input.
between two talkback modes.
Note: After using the solo feature to listen to
1. Use a a Phillips screwdriver to unscrew the
the main console mix between takes, turn the
middle two screws located near the top of the
channel D level control off (to 0) on all HRM-16s
front panel and all screws on the top.
before resuming recording. It is easy to forget to
turn down channel D because you will still hear
2. Remove the top cover. You will see the left-
the intended channel mix but the main console
mix will also be present.
Figure 4 shows the solo interface, labeled
CHANNEL D LEFT & RIGHT ONLY because
all HRM-16 outputs are muted when the SOLO
button is depressed except Channel D. A
Figure 4: Detail of HDS-16 front panel:
¼-inch inputs and Solo interface
switch can be plugged into the ¼-inch SOLO
REMOTE SWITCH connector to turn the solo
function on/off. The SOLO ON LED indicator
lights when the solo function is active.
front corner of the main PCB.
3. Lift the jumper from the J-2 two-pin header and
move it to J-1 to change the talkback mode
from Live/Stage to Studio mode.
This feature allows musicians at the HRM-16s
to hear rough and final mixes or soloed tracks
from the recording console without exiting to
Figure 5: HDS-16 rear panel
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
Note: The remote and front panel switches
are wired in parallel. Although either switch
can activate the SOLO function, both must
be in the off position to deactivate it.
is 200 ft. See Table 1 on page 8 for information
about cable losses beyond 100 ft.
Push the AC-power switch up to the ON posi-
tion to power the HDS-16.
The GROUND lift switch has two positions:
The HDS-16 rear panel has six, 50-pin, Cen-
tronics output connectors for the HRM-16s,
AC-power, and ground switches (Figure 5).
While male-to-male Centronics cables are
available from computer retailers, Furman
manufactures superior quality cables with
twisted pair construction to optimize sound
quality and reject cross-talk interference. We
highly recommend using the 25 twisted pair,
shielded, 25-ft cable supplied with each HRM-
16. Contact Furman for other cable lengths and
linking adapters.
LIFT: Signal ground is separate from chassis
ground. Earth ground (AC line cord) is con-
nected to the chassis only.
GROUNDED: Signal ground is connected to
chassis ground; use this setting unless there is
hum or noise present.
Note: Be sure all units are turned off before con-
necting an HDS-16 to one or more HRM-16’s.
Note: The maximum recommended cable run
Figure 6: HRM-16 top panel
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
■
■
TALKBACK VOLUME control, TALK button,
and built-in microphone;
EFFECTS RETURN level control.
TALKBACK
The HRM-16s receive their input signals and
power supply entirely through the Centronics
cable from the HDS-16. Eight mono and four
stereo channels can be mixed and monitored
with headphones or sent to a monitor system.
The eight mono channels may be routed to
the EFFECTS SEND output on the rear panel.
The effected signal is returned to the HRM-16
through the stereo effect returns on the rear
panel and blended into the mix with the EF-
FECTS RETURN level control. The HRM-16
can be easily mounted on a microphone stand
with the thumb screws and clip provided, or
placed on a table or shelf.
Press the TALK button and speak in the direc-
tion of the built-in microphone above the button
(three small holes in the shape of a triangle).
The microphone will pick up voices from up to
six ft away so you do not need to speak directly
into it. Use the TALKBACK VOLUME control to
alter the level of incoming talkback information.
See page 4 for a complete description of the
talkback functions.
REAR PANEL
The HDS-16/HRM-16 system can be connect-
ed in parallel or series without compromising
sound quality or power as long as no more
than four HRM-16s are connected in series
from a single HDS-16 output.
TOP PANEL
The top panel provides:
■
■
Level controls for four STEREO SOURCES;
■
Parallel: Each HRM-16 is connected directly to
the HDS-16 in a star configuration.
EFFECTS SEND, L/R pan, and level controls
for each of eight mono channels;
■
Series: One HRM-16 is connected directly to
the HDS-16 with additional HRM-16’s con-
nected together in a daisy chain.
■
■
MASTER volume control;
HI and LO shelving EQ controls with 12 dB
boost and cut;
Two, 50-pin, Centronics connectors are located
on the right of the HRM-16’s rear panel:
Figure 7: HRM-16 rear panel
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
INPUT FROM HDS-16
Headphone
Impedance
Power Loss per
100 feet of Cable
This connector delivers the input signals and
power supply from the HDS-16 (parallel) or
from another HRM-16’s OUTPUT TO ADDI-
TIONAL HRM-16’s connector (series).
-0.34 dB
32
693 mW vs. 750 mW
The remaining rear panel inputs and outputs
are ¼-inch TRS connectors.
-0.16 dB
100
■
EFFECTS SEND: Connect this mono output to
an effects processor.
746 mW vs. 770 mW
600
■
EFFECTS RETURN: Use the L input for a
mono return (panned center) or L and R inputs
for stereo effects.
-0.34 dB
257 mW vs. 260 mW
■
LINE OUT: Use this mono, line-level output to
route the HRM-16 to a monitor system. The
LINE OUT and headphone signals are both
affected by the MASTER VOLUME and HI/LO
EQ controls.
Table 1: Centronics cable losses per 100 feet
HRM-16
The headphone driver and power supply regu-
lators are protected against over-temperature
and current overloads. The regulated power
delivered from the HDS-16 to the HRM-16 is
protected against over-current by PolySwitch
resettable fuses inside each HRM-16. These
fuses prevent a defective HRM-16 from shut-
ting down the HDS-16 or attached HRM-16s.
Both devices reset automatically after clearing
the fault and removing power to the circuit.
■
TALKBACK SWITCH REMOTE: Plug a mo-
mentary switch into this jack to use instead of
(or in addition to) the TALK button.
OUTPUT TO ADDITIONAL
HRM-16’S
This connector carries the same signal sent
to the INPUT FROM HDS-16 connector. Con-
nect this output to another HRM-16’s INPUT
FROM HDS-16 connector to achieve a series
connection. An output that simply replicates the
input is often called input through because the
signal is sent out before being processed in
the device. As a result, the HRM-16’s top panel
controls do not affect the OUTPUT TO ADDI-
TIONAL HRM-16’s signal.
The regulated power delivered from the HDS-
16 to the HRM-16 is protected against shorted
cables by an over-current crowbar circuit. The
affected power supply turns off in response
to an over-current condition. Restore normal
operation by removing the defective cable or
HRM-16 and turn off the power to the HDS-16
for at least 30 seconds.
The AC-line fuse is a 1-Amp Slo-Blo. Replace
it only with a fuse of the same type and rating.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
PLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PUR-
POSE. Manufacturer does not warrant against
Furman Sound, Inc., having its principal place
of business at 1997 South McDowell Blvd.,
Petaluma, CA 94954 (“Manufacturer”) warrants
its HDS-16/HR-16 (the “Product”) as follows:
damages or defects arising out of improper
or abnormal use of handling of the Product;
against defects or damages arising from im-
proper installation, against defects in products
or components not manufactured by Manufac-
turer, or against damages resulting from such
non-Manufacturer made products or compo-
nents. This warranty shall be cancelable by
Manufacturer at its sole discretion if the product
is modified in any way without written authori-
zation from Furman Sound. This warranty also
does not apply to Products upon which repairs
have been affected or attempted by persons
other than pursuant to written authorization by
Manufacturer.
Manufacturer warrants to the original Pur-
chaser of the Product that the Product sold
hereunder will be free from defects in material
and workmanship for a period of three years
from the date of purchase. The Purchaser of
the product is allowed fifteen days from the
date of purchase to complete warranty registra-
tion by mail or on-line at the Furman website.
If the Product does not conform to this Limited
Warranty during the warranty period (as herein
above specified), Purchaser shall notify Manu-
facturer in writing of the claimed defects. If the
defects are of such type and nature as to be
covered by this warranty, Manufacturer shall
authorize Purchaser to return the Product to
the Furman factory or to an authorized Furman
repair location. Warranty claims should be ac-
companied by a copy of the original purchase
invoice showing the purchase date; this is not
necessary if the Warranty Registration was
completed either via the mailed in warranty
card or on-line website registration. Shipping
charges to the Furman factory or to an autho-
rized repair location must be prepaid by the
Purchaser of the product. Manufacturer shall, at
its own expense, furnish a replacement Product
or, at Manufacturer’s option, repair the defective
Product. Return shipping charges back to Pur-
chaser will be paid by Manufacturer.
THIS WARRANTY IS EXCLUSIVE. The sole
and exclusive obligation of Manufacturer shall
be to repair or replace the defective Product in
the manner and for the period provided above.
Manufacturer shall not have any other obliga-
tion with respect to the Products or any part
thereof, whether based on contract, tort, strict
liability or otherwise. Under no circumstances,
whether based on this Limited Warranty or
otherwise, shall Manufacturer be liable for in-
cidental, special, or consequential damages.
Manufacturer’s employees or representatives’
ORAL OR OTHER WRITTEN STATEMENTS
DO NOT CONSTITUTE WARRANTIES, shall
not be relied upon by Purchaser, and are not a
part of the contract for sale or this limited war-
ranty. This Limited Warranty states the entire
obligation of Manufacturer with respect to the
Product. If any part of this Limited Warranty is
determined to be void or illegal, the remainder
shall remain in full force and effect.
THE FOREGOING IS IN LIEU OF ALL OTH-
ER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IM-
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HDS-16/HRM-16 HEADPHONE DISTRIBUTION SYSTEM
HDS-16 SPECIFICATIONS
Before returning any equipment for repair,
INPUTS
please be sure that it is adequately packed
Balanced, 50 kΩ, 90 dB CMRR
and cushioned against damage in shipment,
INPUT IMPEDANCE
and that it is insured. We suggest that you
50 kΩ
save the original packaging and use it to ship
LINE OUTPUTS
Balanced or singled ended, 50 Ω, 68 dB OCMR
the product for servicing. Also, please enclose
a note giving your name, address, phone
number, e-mail address (if applicable), and a
SINGLE CHANNEL GAIN
21 dB; +4 dBu for maximum output
description of the problem.
REMOTE SWITCH
Connect tip to ring to mute all outputs except channel D
(solo function)
All equipment being returned for repair must
have a Return Authorization (R/A) Number.
To get a R/A number, please call the Furman
SIZE
3.5” H x 19.0” W x 8.0” D
Service Department at (707) 763-1010 ext.
120 or 121, between 8 a.m. and 5 p.m., U.S.
WEIGHT
9.4 lb (4.27 kg)
Pacific Time. Please display your R/A Number
prominently on the front of all packages.
HRM-16 SPECIFICATIONS
LINE OUTPUTS
Balanced or single ended, 50 Ω, 68 dB OCMR
POWER OUTPUT
750 mW at 32 Ω, 770 mW at 100 Ω , 260 mW at 600 Ω
REMOTE SWITCH
Connect tip to ring to activate the talkback microphone
SIZE
2.9” H x 11.0” W x 7.0” D
WEIGHT
3.5 lb (1.59 kg)
DISTORTION AND NOISE
< 0.002% THD+Noise, 20 Hz - 20 kHz at full rated power
DYNAMIC RANGE
> 105 dB
FREQUENCY RESPONSE
+0/-1 dB 13 Hz - 32 kHz
POWER REQUIREMENTS
HDS-16: 120 VAC, 60 Hz, 82 W; HDS-16E: 230 VAC, 50
Hz, 82 W
CROSSTALK
< -95 dB at 10 kHz
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Furman Sound, Inc.
1997 South McDowell Blvd.
Petaluma, California 94954-6919 USA
Phone: 707-763-1010
Fax: 707-763-1310
E-mail: [email protected]
Made in China
0014
960138-2743 B
Download from Www.Somanuals.com. All Manuals Search And Download.
|