FujiFilm Digital Camera S3 Pro User Manual

Getting Ready  
1
2
3
4
5
6
Basic  
Photography  
Advanced  
Photography  
Advanced  
Features Playback  
Settings  
Connection  
OWNER’S MANUAL  
This manual will show you how to use your  
FUJIFILM DIGITAL CAMERA FinePix S3 Pro correctly.  
Please follow the instructions carefully.  
( )  
BL00430-201 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning  
EC Declaration of Conformity  
We  
Name  
Address  
To prevent fire or shock hazard, do not expose the unit to rain or moisture.  
(
)
:
Fuji Photo Film Europe G.m.b.H.  
Heesenstrasse 31  
to correct the interference by one or more of the following  
For customers in the U.S.A.  
:
measures:  
Tested To Comply  
— Reorient or relocate the receiving antenna.  
— Increase the separation between the equipment and receiver.  
— Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
40549 Dusseldorf, Germany  
With FCC Standards  
FOR HOME OR OFFICE USE  
declare that the product  
Product Name:  
Manufacture’s Name: Fuji Photo Film Co., Ltd.  
FUJIFILM DIGITAL CAMERA FinePix S3 Pro  
— Consult the dealer or an experienced radio/TV technician for  
help.  
You are cautioned that any changes or modifications not  
expressly approved in this manual could void the user’s authority  
to operate the equipment.  
FCC Statement  
This device complies with part 15 of the FCC Rules. Operation  
is subject to the following two conditions: (1) This device may  
not cause harmful interference, and (2) this device must  
accept any interference received, including interference that  
may cause undesired operation.  
-
-
-
Manufacture’s Address: 26 30, Nishiazabu 2 chome, Minato ku,  
-
Tokyo 106 8620, Japan  
Notes on the Grant:  
is in conformity with the following Standards  
To comply with Part 15 of the FCC rules, this product must be  
used with a Fujifilm-specified ferrite-core video cable, IEEE 1394  
cable, USB cable and DC supply cord.  
CAUTION  
:
Safety  
EMC  
EN60065  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try  
:
:
EN55022 1998 Classe B  
EN55024 1998  
EN61000 3 2 1995 A1:1998 A2:1998  
:
For customers in Canada  
CAUTION  
- -  
+
+
:
(
/
/
)
/
/
-
following the provision of the EMC Directive 89 336 EEC, 92 31 EEC and  
This Class B digital apparatus complies with Canadian ICES 003.  
)
(
/
/
/
/
93 68 EEC and Low Voltage Directive 73 23 EEC .  
Please read the Safety Notes (P.141) and make  
sure you understand them before using the camera.  
Dusseldorf, Germany  
Place  
November 1, 2004  
Date  
Signature/Managing Director  
Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u  
ze niet weggooien maar inleveren als KCA  
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
.................................................................................................  
...........................................................................................  
SELF-TIMER PHOTOGRAPHY  
. CONTINUOUS SHOOTING  
9
50  
51  
52  
54  
54  
54  
54  
55  
.........................................................................  
....................................................  
Warning  
2
3
7
8
9
Top display panel  
LCD monitor  
12  
12  
13  
15  
........................................  
..........................................................................  
............................................................  
..................................................  
EC Declaration of Conformity  
Preface  
Rear display panel  
Viewfinder display  
.......................................................................................................  
p MULTIPLE EXPOSURE  
.....................................................  
...................................................  
Accessories included  
Camera parts and features  
................................................................................................................  
METERING SYSTEMS  
............................................  
........................................................................................  
..............................................................................................  
.................................................................................................................  
l Matrix (10-segment) metering  
k Center-weighted metering  
j Spot metering  
ISO SENSITIVITY  
1 Getting Ready  
ATTACHING THE STRAP  
........................................................................................................................  
...............................................................................................................  
16  
17  
18  
19  
21  
22  
24  
25  
26  
27  
28  
29  
29  
EXPOSURE MODES  
..................................................................................................  
MOUNTING THE CAMERA LENS  
Using CPU Nikkor lenses other than G-type lenses  
....................................................................................................  
......................................................................................................................  
................................................................................................  
.............................................................................................  
...............................................................................................................................  
P
AUTO-MULTI PROGRAM  
Program chart  
SHUTTER-PRIORITY AUTO  
APERTURE-PRIORITY AUTO  
MANUAL  
56  
57  
58  
59  
60  
61  
63  
64  
....................................................................  
.........................................................................................................................  
Lens compatibility  
S
A
M
........................................................................................................  
............................................................................................................  
................................................................................................................  
CHARGING THE BATTERIES  
LOADING THE BATTERIES  
INSERTING THE MEDIA  
1
2
3
4
5
6
...................................................................................................  
Bulb photography ()  
b EXPOSURE COMPENSATION  
c AUTO EXPOSURE BRACKETING  
...........................................................................................  
CHECKING THE BATTERY CHARGE  
............................................................................................  
.........................................................  
TURNING ON AND OFF / SETTING THE DATE AND TIME  
CORRECTING THE DATE AND TIME / CHANGING THE DATE ORDER  
......................................................................................  
....................................  
.......................................................................................................  
...............................................................................................................  
DIOPTER ADJUSTMENT  
........................................................................................................................  
FLASH PHOTOGRAPHY  
FLASH PHOTOGRAPHY  
SETTINGS FOR FLASH PHOTOGRAPHY  
BUILT-IN FLASH  
SELECTING THE LANGUAGE  
.............................................................................................................  
.........................................................................  
..........................................................................................................................  
66  
66  
67  
67  
68  
68  
68  
69  
69  
69  
70  
71  
72  
73  
74  
LCD ILLUMINATOR  
................................................  
Flash control modes that can be used with the built-in flash  
2 Basic Photography  
BASIC OPERATION GUIDE  
............................................................................  
..............................................................................  
................................................................................  
.................................................................................  
SYNCHRO MODES AND THEIR FEATURES  
...........................................................................................................  
30  
33  
34  
36  
37  
37  
38  
39  
40  
41  
42  
42  
a
FRONT SYNCHRO MODE  
SLOW SYNCHRO MODE  
REAR SYNCHRO MODE  
RED-EYE REDUCTION MODE  
............................................................................................................................  
Command dials  
ag  
ah  
as  
..................................................................................  
TAKING PICTURES (P Auto-Multi Program)  
Shooting with the camera held on end (vertically)  
NUMBER OF AVAILABLE SHOTS  
.......................................................................  
.......................................................................  
.........................................  
.................................................................................................  
asg RED-EYE REDUCTION SLOW SYNCHRO MODE  
..................................................................................  
Standard number of shots for the media  
...................................................................  
.......................................................................................  
TAKING PICTURES USING THE BUILT-IN FLASH  
.............................................................................................................  
.....................................  
.............................................................................................................................  
AF-ASSIST ILLUMINATOR  
SITUATIONS WHERE AUTOFOCUS MAY NOT WORK AS EXPECTED  
USING AF LOCK  
Effective range of the built-in flash  
....................................................  
......................................................................................  
LENSES THAT CAN BE USED WITH THE BUILT-IN FLASH  
FLASH EXPOSURE COMPENSATION  
........................................................................................  
..............................................................................................  
TAKING PICTURES WITH AE LOCK  
..............................................................................  
NIKON FLASH UNITS THAT CAN BE USED  
DEPTH OF FIELD CHECK BUTTON  
PHOTOGRAPHY FUNCTION MENU  
USING THE FUNCTION MENU WHEN TAKING PICTURES  
...............................................................................................................  
CCD PLANE INDICATOR  
.....................................................  
76  
77  
78  
79  
79  
80  
80  
81  
81  
82  
82  
83  
PLAYBACK MODE  
VIEWING THE IMAGES (w PLAYBACK)  
Single-frame playback  
....................................................................................................................  
..................................................................................................................................  
WHITE BALANCE  
QUALITY  
......................................................................................  
..................................................................................................................  
..........................................................................................................................  
43  
43  
43  
44  
...............................................................................................................  
..................................................................................................................  
...................................................................................................................  
RECORDED PIXELS  
FILM SIMULATION  
Selecting images  
.............................................................................................................................  
Playback zoom  
DYNAMIC RANGE  
COLOR  
TONE  
SHARPNESS  
....................................................................................................................................  
.......................................................................................................................................  
3 Advanced Photography  
...........................................................................................................................  
..................................................................................................................................  
FOCUS SETTINGS  
FOCUS SETTINGS  
Focus-related custom settings  
SELECTING THE FOCUS MODE  
Focus modes  
AF AREA  
......................................................................................................................  
45  
45  
46  
46  
47  
47  
48  
49  
....................................................................................................................  
FUNCTION LOCK  
..................................................................................................................  
FUNCTION RESET  
.............................................................................................  
...............................................................................................  
........................................................................................................................  
............................................................................................  
4 Advanced Features Playback  
SELECTING THE AF AREA MODE  
........  
The displays shown in the viewfinder and on the top display panel are shown below.  
PLAYBACK FUNCTION MENU  
USING THE FUNCTION MENU  
................................................................................................  
.........................................................................................................................  
SELECTING THE FOCUS AREA  
MANUAL FOCUS  
..................................................................................................  
84  
85  
86  
...............................................................................................................................  
HISTOGRAM  
RELEASE MODES  
, SINGLE-FRAME  
.........................................................................................................  
ERASING SINGLE-FRAME  
...................................................................................................................  
50  
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preface  
Contents  
........................................................................................................  
.........................................................................................................  
to other equipment in the hospital or aircraft. For  
details, please check with the applicable regulations.  
Test Shots Prior to Photography  
SINGLE-FRAME PROTECT  
MULTI-FRAME PLAYBACK  
87  
88  
For particularly important photographs (such as  
weddings and overseas trips), always take a test  
photograph and view the image to make sure that the  
camera is functioning normally.  
h Fuji Photo Film Co., Ltd. cannot accept liability for  
any incidental losses (such as the costs of  
photography or the loss of income from  
photography) incurred as a result of faults with this  
product.  
PLAYBACK MENU  
o ERASING ALL FRAMES  
Handling Your Digital Camera  
........................................................................................................  
89  
91  
93  
94  
96  
This camera contains precision electronic  
components. To ensure that images are recorded  
correctly, do not subject the camera to impact or  
shock while an image is being recorded.  
..................................................................  
......................................................................  
................................................................................................................  
..............................................................................................................  
i PROTECTING IMAGES: SET ALL / RESET ALL  
u HOW TO SPECIFY PRINT OPTIONS (DPOF)  
u DPOF SET FRAME  
u DPOF (RESET ALL)  
[ AUTOMATIC PLAYBACK  
Trademark Information  
......................................................................................................  
.............................................................................................................................  
97  
98  
h
and xD-Picture Card™ are trademarks of  
Fuji Photo Film Co., Ltd.  
] TRIMMING  
= LCD BRIGHTNESS  
Notes on Copyright  
..............................................................................................................  
100  
h IBM PC/AT is a registered trademark of International  
Business Machines Corp. of the U.S.A.  
Images recorded using your digital camera system  
cannot be used in ways that infringe copyright laws  
without the consent of the owner, unless intended only  
for personal use. Note that some restrictions apply to  
the photographing of stage performances,  
entertainments and exhibits, even when intended  
purely for personal use. Users are also asked to note  
that the transfer of memory cards (xD-Picture Card or  
Microdrive) containing images or data protected under  
copyright laws is only permissible within the  
restrictions imposed by those copyright laws.  
h Macintosh, Power Macintosh, iMac, PowerBook, iBook  
and Mac OS are trademarks of Apple Computer, Inc.,  
registered in the U.S. and other countries.  
5 Settings  
SET-UP  
.........................................................................................................................................  
101  
101  
102  
103  
103  
103  
103  
103  
104  
105  
105  
105  
106  
106  
106  
107  
108  
109  
110  
110  
111  
......................................................................................................  
............................................................................................................  
®
®
USING THE SET-UP SCREEN  
h Adobe Acrobat Reader is a trademark of Adobe  
Systems Incorporated of the U.S.  
SET-UP menu options  
IMAGE DISPLAY  
...........................................................................................................................  
h Microsoft, Windows, and the Windows logo are  
trademarks, or registered trademarks of Microsoft  
Corporation in the United States and/or other  
countries. Windows is an abbreviated term referring  
............................................................................................  
.............................................................................................................................  
Procedure when “PREVIEW” is set  
Preview zoom  
Histogram  
...................................................................................................................................  
®
®
to the Microsoft Windows Operating System.  
......................................................................................  
.......................................................................................................  
Brightness warning and standard chart  
®
®
The “Designed for Microsoft Windows XP” logo  
refers to the camera and the driver only.  
Liquid Crystal  
SETTING THE CUSTOM WB  
If the LCD monitor is damaged, take particular care  
with the liquid crystal in the monitor. If any of the  
following situations arise, take the urgent action  
indicated.  
h If liquid crystal comes in contact with your skin  
Wipe the area with a cloth and then wash thoroughly  
with soap and running water.  
.......................................................................  
..........................................................................................................................  
When the exposure is not measured correctly  
h Other company or product names are trademarks or  
registered trademarks of the respective companies.  
COLOR SPACES  
D-RANGE  
AUTO ROTATE  
FORMAT  
......................................................................................................................................  
.............................................................................................................................  
.......................................................................................................................................  
Explanation of Color Television System  
NTSC: National Television System Committee, color  
television telecasting specifications adopted  
mainly in the U.S.A., Canada and Japan.  
PAL: Phase Alternation by Line, a color television  
system adopted mainly by European countries  
and China.  
...................................................................................................................................  
FRAME NO.  
h If liquid crystal gets into your eye  
..........................................................................  
..................................................................................................................................  
DISCHARGING RECHARGEABLE BATTERIES  
Flush the affected eye with clean water for at least  
15 minutes and then seek medical assistance.  
h If liquid crystal is swallowed  
Flush your mouth thoroughly with water. Drink large  
quantities of water and induce vomiting. Then seek  
medical assistance.  
LIVE IMAGE  
TWO-BUTTON RESET  
CUSTOM SETTING (CSM)  
Cancelling custom settings  
Custom settings list  
.................................................................................................................  
...........................................................................................................  
........................................................................................................  
................................................................................................................  
Exif Print (Exif ver. 2.2)  
Exif Print Format is a newly revised digital camera file  
format that contains a variety of shooting information  
for optimal printing.  
Notes on Electrical Interference  
If the camera is to be used in hospitals or aircrafts,  
please note that this camera may cause interference  
6 Connection  
CONNECTING TO A TV  
...............................................................................................................  
113  
113  
114  
115  
116  
117  
117  
118  
120  
............................................................................................  
...............................................................................................  
..................................................................................................................  
..........................................................................................................  
USING THE AC POWER ADAPTER  
CONNECTING TO A COMPUTER  
LCD cover  
USE AT DSC MODE  
Disconnecting the camera  
To prevent soiling or damage to the LCD monitor,  
attach the enclosed LCD cover to the camera when  
you are carrying or not using the camera.  
Attach the LCD cover by first fitting it into the grooves  
below the camera’s LCD monitor.  
..........  
CONNECTING THE CAMERA DIRECTLY TO THE PRINTER — PictBridge FUNCTION  
Specifying images for printing on the camera  
Specifying images for printing without using DPOF (single-frame printing)  
............................................................................  
...............................  
...........................................................................................................  
Disconnecting the printer  
.......................................  
....................................................  
.....................  
130  
System Expansion Options  
Accessories Guide  
121  
122  
124  
125  
129  
129  
129  
129  
Notes on Using the Battery Charger  
AC Power Adapter  
Notes on the Media  
Warning Displays  
Troubleshooting  
Specifications  
................................................  
...................................................  
130  
131  
132  
136  
138  
140  
141  
....................  
.....................................................  
Notes on Using Your Camera Correctly  
......................................................  
.........................................................  
............................................................  
Cleaning the CCD  
Notes on the Power Supply  
Applicable Batteries  
Notes on the Batteries  
.......................................  
..............................................  
...........................................  
LCD cover  
................................................  
..............................................................  
Safety Notes  
Explanation of Terms  
.......................  
Using the AA-size Ni-MH Batteries  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Refer to the pages in parentheses for information on  
using the camera parts or features.  
Accessories included  
Camera parts and features  
h AA-size Ni-MH Batteries (HR-AA) (4)  
h Camera body cap (1)  
Fitted on the camera body  
Release mode switch  
unlock button  
Accessory shoe (P.75)  
Accessory shoe cover  
Exposure mode dial  
h Battery charger BCH-NH2 (1)  
Plug-in and cord-attached types are provided  
depending on the intended country of use.  
h Video cable (1)  
(approx. 1.5 m (4.9ft.), mini-plug (3.5 mm-dia.) to  
pin-plug cable)  
Top display panel (P.12)  
Release mode switch  
Synchronizing terminal  
Exposure compensation button (P.63)  
Flash exposure compensation  
button (P.73)  
h IEEE 1394 4-pin to 6-pin cable (1)  
(approx. 1.5 m (4.9ft.))  
h Strap (1)  
LCD illuminator button (P.29)  
Synchronizing  
terminal cap  
Strap mount (P.16)  
h USB cable (mini-B) (1)  
h Accessory shoe cover (1)  
Fitted on the camera body  
Shutter button (P.36)  
Power switch (P.26)  
Sub-command dial (P.33)  
Depth of field check button  
(P.42)  
h Cable holder (1)  
h Clamp filter (1)  
h Eyepiece cap (1)  
AF-assist illuminator (P.38)  
Self-timer lamp (P.51)  
h LCD cover (1)  
Fitted on the camera body  
Shutter button for  
vertical shooting  
(P.36)  
Red-eye reduction lamp (P.69)  
Lock lever for vertical shooting  
(P.36)  
h Synchronizing terminal cap (1)  
Fitted on the camera body  
h Remote release socket cap (1)  
Fitted on the camera body  
h Battery holder (1)  
Fitted on the camera body  
h CD-ROM: Software for FinePix AX (1)  
h Owner’s Manual (this manual) (1)  
h Software Quick Start Guide (1)  
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camera parts and features  
Diopter adjustment knob  
Flash (P.70)  
Flash pop-up button (P.70)  
Rubber eyecup  
Viewfinder  
Lens release button  
Strap mount  
F4 button  
F3 button  
F2 button  
F1 button  
AE-L/AF-L button  
Metering system selector dial  
Synchro mode button (P.68)  
Main-command dial  
(P.33)  
Auto Exposure Bracketing  
button (P.64)  
Battery holder  
release catch  
4-direction button  
Battery holder  
Rear display panel  
(P.14)  
4-direction button  
lock switch  
Focus mode selector switch (P.46)  
Digital terminal cover  
USB socket (mini-B)  
IEEE 1394 socket  
FUNC button  
(P.76, 84)  
MENU/OK button  
BACK button  
PLAY button (P.43)  
LCD monitor (P.12)  
Remote release socket  
(10-pin terminal) (P.62)  
VIDEO OUT (Video output)  
socket  
Slot cover  
unlock button  
DC IN 5V (power input) socket  
Remote release socket cap  
Tripod mount  
CF / Microdrive  
eject button  
Terminal cover  
Access lamp (P.116)  
xD-Picture Card slot  
CF / Microdrive slot  
Slot cover  
10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camera parts and features  
Top display panel  
Rear display panel  
During shooting  
Shutter speed / Exposure  
compensation value  
Aperture  
Photography mode  
Recording icon (when recording)  
Color space  
/
Sensitivity  
Date / Time  
(when AdobeRGB is set)  
Flash exposure  
compensation (P.73)  
Press the “FUNC”  
button to switch  
between functions.  
Battery charge  
indicator  
Custom Setting (P.110)  
Exposure  
compensation (P.63)  
Media  
ISO200  
Battery level warning  
(P.25)  
01 / 01 / 2004  
12 : 00 AM  
Number of available  
shots  
Flexible Program  
(P.56)  
Flash synchro mode (P.68)  
Bracketing bar graphs (P.64)  
Focus area (P.47)  
Auto Exposure Bracketing (P.64)  
!
The LCD used in the top display panel will turn dark at high temperatures and will respond a little more slowly at low  
temperatures. However, it will operate normally again at normal temperatures.  
Quality  
Function lock  
AF area mode  
Film simulation  
LCD monitor  
Function reset  
White balance  
Recorded pixels  
DPOF  
Protection  
Histogram  
Color  
Sharpness  
Dynamic range  
!
There may be some unevenness in the brightness at the bottom of the LCD monitor. This is due to variations in the  
lighting of the LCD itself and is not a fault.  
Tone  
h Photographed image display: For checking  
Record  
Erase  
Standard chart display (P.103)  
Histogram (P.103)  
12  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camera parts and features  
Rear display panel  
Viewfinder display  
During playback  
12mm-dia reference  
circle for center-  
weighted metering area  
(P.54)  
Frame number  
Playback mode  
Color space (only AdobeRGB shown)  
Battery charge indicator  
On-Demand Grid Lines  
(P.111)  
Press the “FUNC”  
button to switch  
between functions.  
Focus area  
Spot metering area  
(P.54)  
Media  
100-0009  
Histogram  
Multi-frame playback  
Protection  
Erase  
Viewfinder information display  
Date / Time  
Shutter speed  
Aperture  
Focus  
indicator (P.36)  
Flash ready-light  
(P.70)  
100-0009  
100-0009  
Focus area (P.47)  
Exposure compensation value  
/ Flash exposure  
Sensitivity  
01 / 01 / 2004 12 : 00 AM  
125 F5.6 ISO200  
compensation value (P.63, 73)  
Metering system (P.54)  
WB:AUTO NORMAL 6M F:STD  
D:  
AUTO C  
:STD T:STD S:STD  
Exposure compensation (P.63)  
Multiple exposure (P.52)  
AE-L (Auto exposure lock)  
indicator (P.41)  
White balance  
Quality  
Sharpness  
Tone  
Color  
Dynamic range  
Flash exposure compensation (P.73)  
Film simulation  
Recorded pixels  
Shutter speed  
Aperture  
Exposure mode (P.56-62) / Electronic  
analog exposure display / Exposure  
compensation value display (P.63)  
!
The viewfinder will be dark without battery power but brightens after installation of fresh batteries. This is not a  
malfunction.  
!
The LCD panel in the upper part of the viewfinder (focus area and On-Demand Grid Lines) will become paler at high  
temperatures and will become darker and respond a little more slowly at low temperatures. However, it will operate  
normally again at normal temperatures.  
!
The LCD panel in the viewfinder display (where the icons and numbers are displayed) will turn dark at high temperatures  
and will respond a little more slowly at low temperatures. However, it will operate normally again at normal temperatures.  
About Advanced Focusing Screen Display  
The new Advanced Focusing Screen Display of the FinePix S3 Pro employs the convenient Vari-Brite  
Focus Area display system; it enables clear display of the focus brackets at the selected focus area in  
the viewfinder for easy identification. When the finder image is bright, the focus brackets are displayed  
in black and when the finder image is dark, the focus brackets are momentarily illuminated in red. The  
selected focus area can be identified easily in both bright and dark conditions with this function.  
Also, the new Advanced Focusing Screen Display allows the superimposition of On-Demand Grid  
Lines. The grid lines can be displayed by using Custom Setting Menu #2 (P.111). These grids assist  
you in composing the frame, in taking landscape pictures or in shifting/tilting PC-Nikkor lenses.  
Due to characteristics of the LCD used in the Vari-Brite Focus Area display system, a thin line  
outside the selected focus area may also be displayed or the entire viewfinder may be illuminated in  
red under certain conditions. These are not malfunctions.  
14  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
Getting Ready ATTACHING THE STRAP  
MOUNTING THE CAMERA LENS  
Pass one end of the strap through the strap mount  
Check the lens type.  
on the camera body.  
1
1
CPU contacts of CPU lens  
The lens is fitted with CPU  
signal contacts.  
G-type Nikkor lens  
(without aperture ring)  
CPU Nikkor lens other  
than G-type  
(with aperture ring)  
Pass the end of the strap through the fastener A  
and B as shown in the figure.  
2
3
1
!
See “Lens compatibility” (P.19) for details.  
Set the Power switch to “OFF” to turn the camera  
off.  
Fastener B  
Fastener A  
2
3
Adjust the strap length. Use the same procedure to  
attach the other end of the strap to the other strap  
mount.  
Position lens in the camera’s bayonet mount so  
that the mounting indexes on lens and camera  
body are aligned, then twist lens counterclockwise  
until it locks into place.  
!
Check that the strap is pulled tight after it is attached.  
Using the cable holder  
Feed the cables through the cable holder.  
IEEE 1394  
!
Always change the lens in an area free of dirt and dust.  
When attaching the lens, take care not to press the lens  
release button.  
!
Cable  
holder  
!
When the lens is not attached or when a non-CPU Nikkor  
lens is attached and the power switch is turned on, “§”  
blinks in the top display panel and viewfinder, and the shutter  
cannot be released. See P.20 for a non-CPU lens.  
Take care not to mount the lens when it is at an angle to the  
camera as this can damage the lens mount on the camera.  
DC IN 5V  
!
Attach the cable holder to the strap mount.  
Strap  
mount  
Continued  
16  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOUNTING THE CAMERA LENS  
Using CPU Nikkor lenses other than G-type lenses  
Lens compatibility  
Set the aperture ring to the minimum aperture.  
Use a CPU lens (except IX-Nikkor) with this camera. D- or G-type AF lenses give you access to all  
available functions (P.17).  
1
Types of CPU lenses and other usable lenses/accessories  
Mode  
Focus mode  
Exposure mode  
Metering system  
Matrix  
Manual with  
electronic  
rangefinder  
Any mode  
Manual other than  
Center-  
Autofocus  
M
Weighted,  
3D 10-  
10-  
1  
M
Spot  
segment segment  
Lens/accessories  
D-type AF Nikkor3  
,
,
G-type AF Nikkor3  
AF-S, AF-I Nikkor  
PC Micro-Nikkor  
85 mm f/2.8D4  
5  
1
7  
7  
AF-I/AF-S Teleconverter6  
Lock the aperture ring. If you turn the camera on  
without first selecting the minimum aperture (the  
aperture setting with the largest number), “¡”  
flashes on the top display panel and in the  
viewfinder, and the shutter will not operate.  
2
Non-D/G-type AF Nikkor (except  
AF Nikkor for F3AF)  
8  
AI-P Nikkor  
AI-S or AI type Nikkor,  
Series-E, AI-modified Nikkor  
8  
10  
Medical-Nikkor  
120 mm f/4  
11  
10  
10  
10  
10  
Reflex-Nikkor  
PC-Nikkor  
5  
Removing the lens  
AI-S or AI type  
Teleconverters  
7  
Push and hold the lens release button, then turn the  
lens clockwise.  
Bellows Focusing  
Attachment PB-612  
7  
Auto Extension Rings  
(PK-11A, PK-12,  
PK-13 and PN-11)  
7  
10  
: Compatible, —: Imcompatible  
1 Spot metering area can be shifted with focus area selector (P.54) with CPU Nikkor lens.  
2 IX-Nikkor lenses cannot be attached.  
3 This camera is compatible with the Vibration Reduction function of the VR Nikkor lens.  
4 The camera’s exposure metering and flash control system do not work properly when shifting and/or tilting the lens, or  
when using an aperture other than the maximum aperture.  
5 Without shifting and/or tilting the lens.  
6 Compatible with AF-S and AF-I Nikkor except AF-S 17-35 mm f/2.8D IF-ED, AF-S 28-70 mm f/2.8D IF-ED, AF-S 12-  
24mm f/4G, AF-S DX ED 17-55mm f/2.8G, AF-S DX ED 18-70mm f/3.5-4.5G, AF-S ED 24-85mm f/3.5-4.5G and AF-S  
VR ED 24-120mm f/3.5-5.6G.  
While the lens is removed from the camera, fit the  
camera body cap provided onto the camera to  
protect the inside of the camera and prevent soiling  
of the mirror and viewfinder screen.  
You can also use the Nikon BF-1A Body Cap.  
7 With maximum effective aperture of f/5.6 or faster.  
8 With maximum aperture of f/5.6 or faster.  
9 Some lenses/accessories cannot be attached (P.20).  
10 With exposure mode set to Manual. The exposure meter cannot be used.  
11 With exposure mode set to Manual and shutter speed set to 1/60 sec. or slower but the exposure meter cannot be  
used.  
12 Can be mounted when used with the Nikon Auto extension ring.  
i
Reprocopy Outfit PF-4 can be attached in combination with Nikon Camera Holder PA-4.  
Continued  
18  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOUNTING THE CAMERA LENS  
CHARGING THE BATTERIES  
Charge the AA-size Ni-MH batteries (HR-AA).  
G-type Nikkor and other CPU Nikkor lens  
h The G-type Nikkor lens has no aperture ring; aperture should be selected from camera body. Unlike  
other CPU Nikkor lenses, aperture does not need to be set to minimum (largest f-number).  
h CPU Nikkor lenses other than G-type Nikkor lens have an aperture ring. Set the lens aperture to its  
minimum and lock. When the lens is not set to its minimum aperture setting and the power switch is  
turned on, “¡” blinks in the top display panel and viewfinder and the shutter cannot be released.  
Batteries that can be charged  
h AA-size Ni-MH batteries (included)  
!
Always use the battery charger BCH-NH2 bundled with the camera to charge Ni-MH batteries. Attempting to charge  
batteries other than those specified for use with the charger (such as manganese, alkaline or lithium batteries) can cause  
the batteries to burst or leak. This could result in a fire or injury and consequent damage to the surroundings.  
When a non-CPU lens is attached  
Load the Ni-MH batteries (included) into the battery  
charger BCH-NH2 bundled with the camera  
correctly as indicated by the polarity icons.  
Set exposure mode to “M” Manual with a non-CPU lens (When other modes are selected, shutter  
cannot be released). The camera’s exposure meter cannot be used and the aperture cannot be set  
using the Sub-command Dial when using non-CPU lenses. “§” appears in place of the aperture  
indication in the top display panel and viewfinder; set/confirm aperture using the lens aperture ring.  
1
2
!
The Ni-MH batteries are not fully charged when purchased  
and must be fully charged before being used.  
!
When first used after purchasing or when left unused for a  
long period, charge and discharge the battery using the  
camera’s “Discharging rechargeable batteries” function and  
then recharge them (P.107).  
1
Nikkor lenses/accessories that cannot be attached to the FinePix S3 Pro  
The following Nikkor lenses/accessories cannot be attached to the FinePix S3 Pro (otherwise camera  
body or lens may be damaged):  
!
If the terminals of battery are soiled, it may not be possible to  
charge them. Clean the battery terminals and battery charger  
terminals with a clean, dry cloth.  
h TC-16A Teleconverter  
h Non-AI lenses  
h 400mm f/4.5, 600 mm f/5.6, 800 mm f/8 and 1200 mm f/11 with Focusing Unit AU-1  
h Fisheye 6 mm f/5.6, 7.5 mm f/5.6, 8 mm f/8 and OP 10 mm f/5.6  
h Old type 21 mm f/4  
h K1, K2 ring, Auto Extension Ring PK-1, PK-11, Auto Ring BR-2, BR-4  
h ED 180-600 mm f/8 (No. 174041-174180)  
h ED 360-1200 mm f/11 (No. 174031-174127)  
h 200-600 mm f/9.5 (No. 280001-300490)  
h 80 mm f/2.8, 200 mm f/3.5 and TC-16 Teleconverter for F3AF  
h PC 28 mm f/4 (No. 180900 or smaller)  
h PC 35 mm f/2.8 (No. 851001-906200)  
h Old type PC 35 mm f/3.5  
h Old type Reflex 1000 mm f/6.3  
h Reflex 1000 mm f/11 (No. 142361-143000)  
h Reflex 2000 mm f/11 (No. 200111-200310)  
Plug the battery charger into a power outlet to  
begin charging. After completing the charging, the  
charging lamp turns off. Unplug the battery charger  
from the power outlet when it is not in use.  
!
If Ni-MH batteries are charged repeatedly before they are  
fully discharged, the battery charge indicator will appear while  
there is still ample charge remaining in the batteries. At that  
time, discharge and recharge them several times using the  
camera’s “Discharging rechargeable batteries” function  
(P.107).  
!
The socket-outlet shall be installed near the equipment and  
shall be easily accessible.  
Plug-in and cord-attached types are provided  
depending on the intended country of use.  
!
The shape of the plug and socket-outlet depends on the  
country of use.  
20  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOADING THE BATTERIES  
Load the AA-size Ni-MH rechargeable batteries in  
the direction indicated by the and labels on  
the holder. Align the battery ends with the terminals  
in the sequence shown in the figure and then  
slowly push them into the place.  
Compatible Batteries  
h AA-size Ni-MH batteries (HR-AA) (4)  
01  
02  
3
4
How to use the battery  
h Use only Ni-MH (nickel-metal hydride) batteries.  
h Never use the following types of batteries, as they could cause serious  
problems such as battery fluid leakage or overheating:  
1. Batteries with split or peeling outer casings  
2. Combinations of different types of batteries or new and used batteries  
together  
h Soil (such as fingerprints) on the battery terminals makes the batteries charge less reducing the  
number of images they will allow you to take. Carefully wipe the battery terminals with a soft dry cloth  
before loading.  
Outer casing  
03  
h See P.129 for other notes on using batteries.  
04  
!
Remove the batteries more easily by pushing the batteries  
upwards from the gap at the opposite end from the battery  
holder release catch.  
1
h When first used after purchasing or left unused for a long period, the time for which AA-size Ni-MH  
rechargeable batteries can be used may be shorter. You are advised to check the detailed  
information provided on P.129 and then charge the batteries before using the camera (within 1 week).  
Push the battery holder in and hold it in place as  
you turn the battery holder release catch clockwise  
to securely lock the battery holder.  
Set the Power switch to “OFF” to turn the camera  
off.  
1
01  
02  
1Lift out the battery holder release catch.  
2Turn the battery holder release catch  
counterclockwise to unlock the battery holder.  
3Pull the battery holder out.  
2
03  
01  
03  
02  
22  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSERTING THE MEDIA  
Use either xD-Picture Card or CF/Microdrive as recording media in the FinePix S3 Pro.  
How to replace the CF/Microdrive  
h If an xD-Picture Card and a CF/Microdrive are inserted at the same time, images will be recorded  
onto the media selected as the “MEDIA” (P.102).  
h Data cannot be copied between the two media types on the FinePix S3 Pro.  
Open the slot cover, press the CF/Microdrive eject  
button and remove the CF/Microdrive.  
CF/Microdrive  
eject button  
Set the Power switch to “OFF” and check that the  
Access lamp  
access lamp is off. Then open the slot cover.  
1
!
When storing CF/Microdrives, always use the special  
protective case.  
Never open the slot cover while the camera is on.  
This could destroy the image data or damage the  
media itself.  
CHECKING THE BATTERY CHARGE  
Turn the camera on and check the battery charge indicator.  
1
xD-Picture Card  
CF/Microdrive  
Top display panel  
2
3
1No icon  
Batteries charged.  
2Blinking  
No remaining battery charge. Lights when there is no  
Camera shutting down. remaining battery charge and  
the camera shutdown  
3Lit  
Gold marking  
Align the gold marking on the xD-Picture  
Card slot with the gold contact area on  
the xD-Picture Card and push the card  
firmly all the way into the slot.  
Push the CF/Microdrive firmly all the way  
into the CF/Microdrive slot.  
Compatibility is listed on Fujifilm website:  
procedure has been completed.  
The batteries must be replaced.  
Rear display panel  
!
Insert only the appropriate media types into the xD-Picture Card and CF/Microdrive slots. Inserting the incorrect  
media will damage the camera or media.  
If the media is oriented incorrectly, it will not go all the way into the slot. Do not apply force when inserting an xD-  
Picture Card or CF/Microdrive.  
If the media is not fully inserted into the slot, “`” appears.  
1There is ample charge in  
the batteries.  
2The batteries are flat.  
Have replacement batteries  
ready.  
3The batteries are fully  
depleted. You must replace  
the batteries.  
!
Lit  
1
2
3
ISO200  
!
Lit  
09 / 23 / 2004  
10 : 00 AM  
Close the slot cover.  
Blinking  
!
If you turn the camera on again after the icon in 3 has been displayed, the  
icon in 1 may reappear but there is actually no charge left in the batteries and  
they must be replaced.  
h If the camera loses power while it is shooting or saving an image, it cannot save the photographed  
image. Note the battery level carefully when shooting long-exposure images (e.g. bulb photography)  
or when shooting images that will take some time to save (continuous shooting or shots with the  
quality set to “HIGH”).  
h Use the optional AC adapter (AC-5VX) when camera is used for long periods for indoor shots, etc.  
The camera displays no battery level icons when the AC adapter is used.  
How to replace the xD-Picture Card  
Push the xD-Picture Card into the slot and then  
slowly remove your finger. The lock is released and  
the xD-Picture Card is pushed out.  
Auto Power Off Function  
If you leave the camera turned on without using it, this function automatically turns the camera off (P.112).  
When the Auto Power Off function has turned the camera off, restore power to the camera by pressing the  
shutter button on the top of the camera down halfway or by pressing the LCD illuminator button.  
!
Auto Power Off cannot be cancelled using the shutter button for vertical shooting.  
24  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TURNING ON AND OFF / SETTING THE DATE AND TIME  
CORRECTING THE DATE AND TIME / CHANGING THE DATE ORDER  
To turn the camera on, set the Power switch to  
“ON”.  
To turn the camera off, set the Power switch to  
“OFF”.  
1Unlock the 4-direction button.  
2Press the “MENU/OK” button.  
01  
02  
1
1
2
1Press “d” or “c” to move to option 3 and then  
press “a” or “b” to select “DATE/TIME”.  
2Press “c”.  
T-UP  
1
2
3
4
5
EEP          OW  
After purchasing the camera, first time when  
turning camera on, the date and time are cleared.  
Press the “MENU/OK” button to set the date and  
time.  
DA        SET  
SB MODE          :  
394 MODE        :  
2
3
4
NCEL  
T  
1
  T  
01  
02  
!
If the message (see figure at left) does not appear, refer to  
“Correcting the date and time” (P.27) and check and correct  
the date and time settings.  
NO  
SET  
!
The message also appears when the batteries have been  
removed and the camera has been left for a long period.  
To set the date and time later, press the “BACK” button.  
If you do not set the date and time, this message will appear  
each time you turn the camera on.  
!
Correcting the date and time  
1Press “d” or “c” to select Year, Month, Day,  
Hour or Minute.  
2Press “a” or “b” to correct the setting.  
3Always press the “MENU/OK” button after the  
settings are completed.  
ATETIME  
!
3
YYYM.DD  
20  .   9  .  23  
0         M  
1Unlock the 4-direction button.  
DATE/TIME  
2Press “d” or “c” to select Year, Month, Day,  
Hour or Minute and then press “a” or “b” to  
adjust the selected setting.  
YYYY.MM.DD  
CANCEL  
T  
2004  .   1  .   1  
         M  
01 02  
01 02  
03  
!
Holding down “a” or “b” changes the numbers continuously.  
When the time displayed passes “12:00”, the AM/PM setting  
changes.  
NCEL  
SET  
!
01  
01  
02  
!
Holding down “a” or “b” changes the numbers continuously.  
When the time displayed passes “12:00”, the AM/PM setting  
changes.  
Changing the date order  
1Press “d” or “c” to select the date order.  
2Press “a” or “b” to set the order. Refer to the  
table below for details of the settings.  
3Always press the “MENU/OK” button after the  
settings are completed.  
DAE  
!
M/DY  
 9    23  /  2004   
10         M  
1Once you have set the date and time, press the  
“MENU/OK” button.  
2When you have finished the procedure, lock  
the 4-direction button to prevent accidental  
improper use.  
DATE/TIME  
YYYY.MM.DD  
NCEL  
SET  
Date order  
Explanation  
2004  .   9  .  23  
10         M  
Displays the date in the “year. month. day”  
format.  
03  
YYYY.MM.DD  
Displays the date in the “month / day / year”  
format.  
MM/DD/YYYY  
DD.MM.YYYY  
CANCEL  
SET  
!
At the time of purchase and after leaving the camera for a  
long period with the batteries removed, settings such as the  
date and time are cleared. Once the AC power adapter has  
been connected or the batteries have been loaded for 2 days  
or more, the date and time settings will be retained for  
roughly 6 months even when the camera has no power  
(batteries removed and AC power adapter disconnected).  
Displays the date in the “day. month. year”  
format.  
02  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
4
26  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SELECTING THE LANGUAGE  
DIOPTER ADJUSTMENT / LCD ILLUMINATOR  
1Turn the camera on.  
2Press the “MENU/OK” button to display the SET-  
UP screen.  
DIOPTER ADJUSTMENT  
The finder diopter enables near- or far-sighted photographers to adjust the eyepiece diopter to suit  
their vision.  
01  
02  
1
While looking through the viewfinder, adjust the  
position of the diopter adjustment knob until the  
focusing frame or the image in the viewfinder  
appears sharpest.  
h The diopter setting can be adjusted from –2.0 m-1  
(shortsighted) to +1.0 m-1 (farsighted). Nikon also  
provides 9 types of diopter adjustment lens  
ranging from –5 m-1 to +3 m-1.  
1The “SET-UP” screen appears. Press “d” or “c”  
to move to option 4 and then press “a” or “b” to  
01  
02  
2
select “  
2Press “c” to select “ENGLISH”, “FRANCAIS”,  
“DEUTSCH”, “ESPAÑOL”, “ITALIANO”, “  
or “ ”. Press “c” to cycle through the  
”.  
1
SET-UP  
1
language settings.  
2
3
4
5
FRAME NO.       :CONT.  
言語  
/LANG.       ENGLISH  
Since the diopter adjustment knob is located next to the viewfinder, be careful not to poke yourself  
in the eye with your finger or fingernail while sliding the knob.  
VIDEO SYSTEM    :NTSC  
DISCHARGE       :OK  
!
The screens in this manual are shown in English.  
See P.102 for more information on the “SET-UP” menu.  
CANCEL  
T  
!
LCD ILLUMINATOR  
Displays in the top and rear display panels can be confirmed in the dark with the LCD illuminator.  
When you press the “m” LCD illuminator button,  
the top and rear display panels light up.  
h Display panel illumination turns off in the  
following situations:  
i When you press the “m” LCD illumination  
button again  
i When you release the shutter  
i When the Auto Power Off function turns the  
camera off  
!
Pressing the shutter button down halfway temporarily turns  
display panel illumination off.  
CSM 14: The illuminator can be set to come on when any button is pressed (P.112).  
28  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic  
2
Photography  
BASIC OPERATION GUIDE  
xAccessory shoe  
Mount an external flash here.  
xSub-command dial  
Changes the aperture and other  
settings.  
xFlash pop-up button  
To use the built-in flash, press  
this button to pop-up the flash.  
xDepth of field check  
button  
xPower switch  
This button allows you to  
check the depth of field.  
Turns the camera on  
and off.  
xShutter button  
Press this button down halfway to  
restore the camera to  
Photography mode. Press down  
fully to take a picture.  
xLens release button  
Hold down this button as  
you remove the lens.  
xExposure compensation  
xSynchronizing terminal  
Use this to connect flash units  
that require a synchro cord.  
button  
xFlash exposure  
compensation button  
Used with the Main-command  
dial to select the exposure  
compensation value.  
Used with the Main-command dial  
to select the flash exposure  
compensation value.  
xRemote release socket  
Used to connect a 10-pin  
remote release.  
xLCD illuminator button  
Illuminates the display panel.  
2
xAuto exposure bracketing button  
Used with the camera dials to select Auto Exposure Bracketing.  
xFocus mode selector switch  
Selects AF-S (Single-AF servo), AF-C  
(Continuous-AF servo) or M (Manual)  
as the focus mode.  
Main-command dial: Turns Auto Exposure Bracketing ON and OFF.  
Sub-command dial: Selects a combination of exposure offset and number of shots.  
xSynchro mode button  
Used with the Main-command  
dial to select Synchro mode.  
xDiopter adjustment knob  
xExposure mode dial  
Makes the image in the viewfinder easier to see.  
Set this knob to the position where the focusing  
area appears sharpest.  
Allows you to select the exposure  
mode, the custom settings and  
the ISO setting,  
xRelease mode  
switch unlock  
button  
Hold down this button  
to move the release  
mode switch.  
 
 
: Programmed Auto  
: Shutter-priority Auto  
xTop display panel  
  : Aperture-priority Auto  
  : Manual  
Displays the information  
shown in the viewfinder  
along with other information.  
 
 
: Custom settings  
: ISO setting (sensitivity)  
xMetering system selector dial  
Selects Multi, Center-weighted or Spot  
as the metering system.  
xAE-L / AF-L button  
Locks the exposure and focus while  
pressed.  
xRelease mode switch  
Selects Single-frame, Continuous, Self-timer or Multi  
Exposure as the shutter release mode.  
xMain command dial  
Changes settings such as the  
shutter speed.  
30  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION GUIDE  
Command dials  
xFUNC button  
Selects the information displayed  
on the rear display panel.  
x F1 to F4 buttons  
Use these buttons to select items in the rear display panel.  
The FinePix S3 Pro’s Main- and Sub-command dials are used alone or in combination with  
other buttons to select/set various functions or modes.  
x4-direction button  
Use this button to select menu  
options or the focus area.  
Sub-command  
dial  
xRear display panel  
Displays information during  
shooting or playback.  
Exposure mode dial  
Flash exposure  
compensation  
x4-direction button lock  
switch  
Release this switch to use the  
button  
Auto Exposure  
Bracketing button  
Exposure  
compensation  
button  
4-direction button.  
Main-  
command dial  
xMENU/OK button  
Press this button to confirm an  
action in the menu screen.  
Synchro mode  
button  
Setting  
Exposure mode setting  
Procedure  
2
xBACK button  
Press this button to cancel an  
action in the menu screen.  
Main  
Main  
Program shift  
P”  
xPLAY button  
Switches playback  
display on and off.  
x Access lamp  
Lights during media access.  
Faster  
Close  
Shutter speed setting  
Aperture setting  
S, M”  
A, M”  
Slower  
Sub  
Open  
xPlayback, Menu and SET–UP Operations  
Main  
Main  
Sub  
Exposure compensation amount  
Auto Exposure Bracketing ON/OFF  
P, S, A, M”  
Photography  
LCD monitor  
OFF  
P, S, A, M”  
Number of shots and exposure offset for Auto  
Exposure Bracketing  
Main  
Main  
Main  
Main  
Sub  
Shutter button pressed halfway  
Menu  
Synchro mode setting  
P, S, A, M”  
Playback  
SET-UP  
SET-P  
RASE  
Flash exposure compensation amount  
Sensitivity setting  
2
3
4
5
1
ALL FRMES  
BACK  
IMAGE DISP.      OFF  
CUSTOM WB       :SET  
COLOR SPCES    :sGB  
D-RANGE          :WIDE  
ISO”  
CANCL  
SET  
Custom setting option selection  
Custom setting option modification  
Frame advance : dc  
Playback zoom : ab  
1Menu option selection : dc 1Option selection : ab  
2Setting selection : ab  
3Confirmation : MENU/OK  
Cancel : BACK  
2Setting selection : dc  
CSM”  
32  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(
)
TAKING PICTURES P Auto-Multi Program  
Set the focus mode selector switch to “S” (Single-  
AF Servo).  
Set the metering system selector dial to “/”  
(Matrix metering).  
1
6
7
!
Make sure to turn the focus mode selector switch until it  
clicks into position.  
1Press the “FUNC” button to display the AF  
setting on the rear display panel.  
2Press the “F1” button to select “7” Single area  
AF.  
01  
02  
2
!
Matrix metering indication “l” appears in the viewfinder.  
Set the Exposure mode dial to “P” (Auto-Multi  
Program).  
Single  
Area AF  
2
Dynamic  
AF  
1Unlock the 4-direction button.  
2Press “d”, “c”, “a” or “b” to position the  
focusing area in the center.  
01  
02  
3
Brace your elbows against your body and hold the  
camera with both hands.  
8
9
!
When shooting with the camera held vertically, see the  
section on vertical shooting (P.36).  
!
The selected focus area indicator appears on the top display  
panel, in the viewfinder display and on the viewfinder screen  
(P.47).  
!
Take care not to obscure the lens with your fingers or the  
shoulder strap.  
Lock the 4-direction button to prevent accidental  
improper use.  
Position the central focus area over the subject.  
4
5
!
If the subject is outside the focus area, either move the focus  
area or take the picture using the AF Lock function (P.40).  
Hold down the release mode switch unlock button  
and set the release mode switch to “,” (Single-  
frame).  
Continued  
34  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(
)
TAKING PICTURES P Auto-Multi Program  
Press the shutter button down halfway to focus the  
shot. The focus indicator “” appears in the  
viewfinder display.  
NUMBER OF AVAILABLE SHOTS  
10  
The number of available shots is displayed on the  
rear display panel.  
ISO200  
09 / 23 / 2004  
10 : 00 AM  
!
See P.78-79 for information on changing the number of  
recorded pixels/Quality (compression ratio) setting.  
The factory default settings set at shipment are 6M and N  
(Quality: NORMAL).  
!
Standard number of shots for the media  
!
If the focus indicator is flashing, the camera cannot focus and  
the shutter will not release.  
Because the amount of data needed to record an image varies slightly depending on the type of subject, the number of  
available shots may not decrease after an image is recorded, or may decrease by 2 in some cases. Also, the difference  
between the standard number of shots and the actual number of available shots increases for media with a higher capacity.  
Number of recorded  
pixels  
4256 × 2848  
3024 × 2016  
2304 × 1536  
1440 × 960  
Without releasing the shutter button, press it down  
all the way (fully pressed) to take the shot.  
CCD-RAW  
HIGH  
4
3
2
1
`
11  
Quality Mode  
FINE NORMAL FINE NORMAL FINE NORMAL FINE NORMAL  
D-RANGE D-RANGE  
WIDE STANDARD  
2
Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx.  
Image File Size  
25 MB  
13 MB 4.7 MB 2.4 MB 3.0 MB 1.5 MB 1.7 MB 880 KB  
1 MB  
520 KB  
DPC-16 (16 MB)  
DPC-32 (32 MB)  
DPC-64 (64 MB)  
DPC-128 (128 MB)  
DPC-256 (256 MB)  
DPC-512 (512 MB)  
Microdrive (340 MB)  
Microdrive (1 GB)  
0
1
1
2
3
6
6
5
10  
20  
8
17  
35  
14  
29  
13  
10  
17  
30  
59  
2
4
13  
26  
53  
107  
73  
220  
26  
21  
42  
36  
72  
61  
120  
241  
484  
967  
671  
1932  
(
)
5
9
53  
42  
84  
72  
144  
290  
580  
396  
1173  
122  
245  
491  
338  
995  
Shooting with the camera held on end vertically  
The shutter button for vertical shooting makes taking pictures in this mode as convenient as normal  
shooting.  
10  
20  
13  
41  
19  
39  
27  
81  
107  
214  
146  
437  
85  
169  
339  
232  
698  
146  
292  
200  
597  
170  
116  
349  
Unlock the shutter button for vertical shooting.  
Shutter button for  
vertical shooting  
1
Number of available shots for formatted media.  
Lock lever for  
vertical shooting  
Hold the camera vertically to take the picture.  
2
!
When you are not using the shutter button for vertical  
shooting, engage the lock lever for vertical shooting to  
prevent the shutter button from being pressed by mistake.  
Auto Power Off cannot be cancelled using the shutter button  
for vertical shooting. Press the shutter button on the top of  
the camera to restore power to the camera.  
!
36  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AF-ASSIST ILLUMINATOR  
SITUATIONS WHERE AUTOFOCUS MAY NOT WORK AS EXPECTED  
When the subject is dark and the shutter button is pressed down halfway, the camera’s AF-assist  
illuminator automatically turns on and enables autofocus operation in a dark environment.  
Autofocus may not work as expected in the following situations. In such situations, focus manually  
using the clear matte field or focus on a different subject located at the same distance, use AF lock  
(P.40) then recompose.  
AF-assist illuminator automatically turns on in the  
following situations:  
Low-contrast scenes  
For example, where the subject is wearing clothing  
the same color as a wall or other background.  
Focus mode is Single AF servo, AF Nikkor lens is  
used, subject is dark and center focus area is  
selected or Dynamic AF Mode with Closest Subject  
Priority is activated.  
Focal length of the usable AF Nikkor lens is 24-200  
mm and the distance range of the AF-assist  
illuminator is approx. 0.5-3 m (1.6-9.8 ft.).  
Scenes with subjects within the focus brackets  
located at different distances from the camera  
For example, when shooting an animal in a cage or  
a person in a forest.  
Approx. 0.5-3 m  
(1.6-9.8 ft.)  
2
CSM 15: AF-assist illuminator can be cancelled (P.112).  
Patterned subject or scene  
For example, building windows.  
When the AF-assist illuminator is used continuously, illumination is limited temporarily to protect  
the firing tube. The illumination restarts after a few moments. Also, when the AF-assist illuminator  
is used repeatedly in a short period of time, be careful not to touch the AF-assist illuminator lamp  
because it may have become hot.  
Nikon flash units and active assist illuminator  
If you use an SB-28/28DX, SB-27, SB-26, SB-25, SB-24, SB-800 or SB-600 Nikon flash to take  
pictures when the conditions for active assist illuminator are met, the active assist illuminator on the  
Nikon flash automatically fires. With other Nikon flash models, the AF-assist illuminator on the camera  
automatically lights.  
Scenes with pronounced differences in brightness  
within the focus brackets  
For example, when the sun is in the background  
and the main subject is in shadow.  
Lenses for which vignetting occurs  
h Autofocus using the camera’s AF-assist illuminator cannot be performed due to vignetting with  
following lenses at shooting distance within 1m (3.3 ft):  
i AF Micro 200 mm f/4 IF-ED  
i AF-S 17-35 mm f/2.8 IF-ED  
i AF 18-35 mm f/3.5-4.5 ED  
i AF 20-35 mm f/2.8 IF  
i AF 24-85mm f/2.8-4D  
i AF-S DX 18-70mm f/3.5-4.5G  
i AF-S VR ED 24-120mm f/3.5-5.6G  
i AF 24-120 mm f/3.5-5.6 IF  
i AF-S 28-70 mm f/2.8 IF-ED  
i AF Micro 70-180 mm f/4.5-5.6 ED  
i AF 24-85 mm f/2.8-4  
i AF-S DX ED 12-24mm f/4G  
i AF-S ED 24-85mm f/3.5-4.5G  
i AF ED 28-200mm f/3.5-5.6G  
h At shooting distances of 2 meters or less, the AF-S DX ED 17-55mm f/2.8G (IF) cannot be used for  
autofocus photography where the AF-assist illuminator is used.  
h Autofocus using the camera’s AF-assist illuminator cannot be performed due to vignetting with AF-S  
80-200 mm f/2.8 IF-ED, AF 80-200 mm f/2.8 ED, AF VR 80-400 mm f/4.5-5.6 ED, AF-S VR ED 70-  
200mm f/2.8D and AF-S VR ED 200-400mm f/4G.  
38  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING AF LOCK  
TAKING PICTURES WITH AE LOCK  
If you take a shot with this type of composition  
using Single-area AF with the focus area in the  
center, the subjects (the two people in this case)  
are outside the focus area and will not be in focus.  
AE lock allows you to set the exposure for a specific subject in your shot. This technique is useful  
when brightness of your subject differs greatly from its surroundings.  
1
Set the metering system selector dial to “-”  
Center-weighted or “0” Spot metering.  
Center-weighted metering  
1
h Matrix metering is not recommended since the  
effect of the Auto Exposure Lock cannot be  
effectively attained.  
Spot metering  
Move the camera slightly so that one of the  
subjects is in the AF frame.  
2
3
Position the focus area over the subject you want  
correctly exposed, press and hold the shutter  
button down halfway and then press the “AE-L/AF-  
L” button. The “EL” (exposure lock) indicator  
appears in the viewfinder.  
2
h The exposure and focus are locked as long as  
the “AE-L/AF-L” button is held down (default  
setting).  
h If you press the “AE-L/AF-L” button in the “AF-S”  
or “AF-C” focus mode when the shot is not in  
focus, the exposure is locked with the shot out of  
focus. Always check that the focus indicator “”  
is lit.  
2
Keep the shutter button pressed down halfway (AF  
lock) and check that the focus indicator “” is lit in  
the viewfinder display.  
While keeping the “AE-L/AF-L” button pressed,  
recompose, focus and shoot.  
3
!
If you are using the “AF-C” focus mode, hold the shutter  
button down halfway and press the “AE-L/AF-L” button  
(P.41).  
h Because the settings are maintained after you  
take the shot for as long as the “AE-L/AF-L”  
button is held down, you can keep the same  
settings as you recompose the shot.  
h The following functions can be operated while the  
“AE-L/AF-L” button is kept pressed:  
1. In “P” exposure mode: Sets program shift.  
2. In S” exposure mode: Changes the shutter  
speed.  
Continue to hold the shutter button down halfway  
(AF lock). Move the camera back to the original  
image and then fully press down on the shutter  
button.  
4
3. In “A” exposure mode: Changes the aperture.  
h Rotating the metering system selector to another  
setting does not change the metering system  
during Auto Exposure Lock operation. Release  
the AE lock.  
!
You can reapply the AF lock as many times as you like  
before releasing the shutter.  
The AF lock operates in all photography modes and can be  
used to ensure excellent results.  
CSM 5: Auto Exposure Lock can be set to be activated by pressing the shutter button down  
!
halfway (P.111).  
CSM 9: The operation performed when the “AE-L/AF-L” button is pressed can be modified  
(P.111).  
When AF (Auto Focus) does not focus the shot  
h Position the focus area over another subject at roughly the same distance and press the shutter  
button down halfway. Then recompose the shot and take the picture.  
Operation: AF/AE lock (default setting), AE lock only, AF lock only, AE lock maintained, AF  
operation  
h You can also set the focus and take the shot by selecting “M” (manual) as the focus mode.  
40  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK MODE  
(
)
DEPTH OF FIELD CHECK BUTTON / CCD PLANE INDICATOR  
VIEWING THE IMAGES w PLAYBACK  
DEPTH OF FIELD CHECK BUTTON  
Depress the depth of field check button to confirm the depth of field through the viewfinder.  
Single-frame playback  
1Press the “PLAY” button to view your images.  
2Unlock the 4-direction button.  
3Press “c” to scan forward through your images.  
Press “d” to scan backwards.  
01  
02  
Pressing the depth of field check button stops the  
lens down to the aperture controlled in “P” Auto-  
Multi Program or “S” Shutter-Priority Auto exposure  
mode, and down to the aperture selected in “A”  
Aperture-Priority Auto or “M” Manual exposure  
mode. By looking through the viewfinder, the  
approximate depth of field with the given aperture  
can be confirmed.  
03  
!
Pressing the “PLAY” button displays the last image  
photographed.  
Selecting images  
!
When you press the depth of field check button, the shutter  
speed display and LCD illumination both turn off.  
To select images on the thumbnail lists screen,  
hold down “d” or “c” for approx. 1 second during  
playback.  
CCD PLANE INDICATOR  
The CCD plane indicator shows the position of the CCD plane inside the camera body.  
2
The CCD plane indicator shows the standard line of  
the shooting distance and indicates the position of  
the CCD plane inside the camera body. Use this  
indicator when actually measuring camera-to-  
subject distance, e.g. in close-up photography. The  
exact distance from the lens mounting flange to the  
CCD plane is 46.5 mm.  
Displaying the photography data  
Press the “FUNC” button during image playback to check the photography data for the currently  
displayed frame.  
Playback mode  
Frame number  
Press the “FUNC”  
button to switch  
between  
100-0009  
functions.  
Shutter speed  
Aperture  
100-0009  
100-0009  
Date /  
Time  
Sensitivity  
09 / 23 / 2004 10 : 00 AM  
125 F5.6 ISO200  
WB:AUTO NORMAL 6M F:STD  
:STD S:STD  
D:AUTO C:STD T  
Sharpness  
Tone  
White balance  
Recorded  
pixels  
Dynamic range  
Color  
Quality  
Film simulation  
Still images viewable on the FinePix S3 Pro  
This camera will display still images recorded on the FinePix S3 Pro or still images (excluding some  
uncompressed images) recorded on any FUJIFILM digital camera that supports xD-Picture Cards or  
CF/Microdrives.  
Clear playback or playback zooming may not be possible for still images shot on cameras other than  
the FinePix S3 Pro.  
42  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced  
PLAYBACK MODE  
FOCUS SETTINGS  
(
)
VIEWING THE IMAGES w PLAYBACK  
3
Photography  
FOCUS SETTINGS  
Pages 45 to 49 provide explanations of how to use and set the camera’s focusing functions, along  
with various related topics. The diagram below is a page map to this section. Refer to the pages  
indicated for details.  
Playback zoom  
Press the “a” or “b” during single-frame playback  
to zoom (enlarge) the still image. A zoom bar  
appears.  
Press the “BACK” button to return to single-frame  
playback.  
AF-S or AF-C  
MF  
Selecting the focus mode (P.46)  
Zoom bar  
Switches between:  
MF AF-S AF-C  
S: Single-AF servo  
C: Continuous-AF servo  
M: Manual focus  
PANNING  
1Press “PLAY” button to select to “PANNING”.  
2Press “a”, “b”, “d”, or “c” to display another  
area.  
01  
02  
Single  
Dynamic  
Selecting the AF area mode (P.47)  
The current displayed image appears on the  
navigation screen.  
Press the “PLAY” button to return to playback  
zoom.  
Select the number of focus areas used for  
focusing.  
Single: 1  
Dynamic: 5  
OFF  
ON  
Closest-subject priority setting  
Navigation screen  
3
ON: The camera focuses using the focus  
area containing the closest subject.  
OFF: The camera focuses using the specified  
focus area.  
ZOOM  
Zoom scales  
Quality mode  
Max. zoom scale  
Approx. 26.6×  
(4256 × 2848 pixels)  
(3024 × 2016 pixels)  
(2304 × 1536 pixels)  
(1440 × 960 pixels)  
4
3
2
1
(
)
Manual choose from 5 points  
Automatic  
Selecting the focus area (P.48)  
Approx. 18.9×  
Approx. 14.4×  
Approx. 9.0×  
Manual: Select the focus area to be used for  
focusing.  
Automatic: This option is disabled when the  
closest-subject priority setting is  
“ON”.  
Focus-related custom settings  
CSM 3: Illumination for focus area  
Sets the automatic illumination setting for the focus area  
in the viewfinder  
P.111  
P.111  
P.111  
CSM 4: Focus area selection  
Sets the focus area selection method  
CSM 7: Closest-subject priority dynamic AF at S-AF Closest-subject priority dynamic AF settings  
mode  
CSM 8: Closest-subject priority dynamic AF at C-AF Sets the closest-subject priority dynamic AF settings  
P.111  
P.111  
mode  
CSM 9: AE-L/AF-L button  
Selects AE/AF concurrent locking, independent locking,  
or maintained locking  
44  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOCUS SETTINGS  
FOCUS SETTINGS  
SELECTING THE FOCUS MODE  
SELECTING THE AF AREA MODE  
Use the focus mode selector switch to select the  
focus mode.  
You can change the focusing method used for automatic focusing (when the focus mode selector  
switch is set to “S” or “C”).  
MF  
AF-S  
AF-C  
i Focuses using the selected focus area.  
i Useful for situations where you want to focus accurately on a more or less stationary  
Single-area AF  
7
subject.  
i If the subject is outside the specified focus area, another focus area is used for focusing.  
Dynamic AF  
8
i Useful for shots where it is difficult to accurately keep the subject in a given focus area,  
such as when you are tracking a moving subject (particularly one that moves in  
unpredictable ways).  
Closest-subject i Focuses using the focus area containing the subject closest to the camera.  
Priority AF  
If spot metering is used in Closest-subject Priority AF mode, metering is always performed for the focus area in the center  
of the shot.  
When you are using a telephoto lens or the subject is dark, the closest focus area may not be selected.  
CSM 7/8: The focus mode determines whether Closest-subject Priority AF is ON or OFF. The  
default settings are “ON” in “S” (Single-AF servo) mode and “OFF” in “C” (Continuous-AF  
servo) mode. You can change these settings using the custom settings (P.111).  
Focus modes  
AF-S  
(S: Single-AF servo)  
AF-C  
(C: Continuous-AF servo)  
MF  
(M: Manual focus)  
Features  
Focus priority mode. The Release priority mode. The Allows you to release the  
shutter will only release if the shutter will release even if the shutter at any time.  
focus indicator “” is focus indicator “” is not  
Press the “FUNC” button to display this screen.  
1
displayed.  
(Excludes displayed.  
predictive motion focusing)  
AF starts  
When the shutter button is When the shutter button is AF is not used.  
pressed  
(default).  
down  
halfway pressed  
(default).  
down  
halfway  
Focus lock  
When the shutter button is Even when the shutter button The focus is not locked.  
held down halfway and the is held down halfway and the  
focus indicator “” is focus indicator “” is  
displayed, the focus is locked. displayed, the focus is not  
locked and focusing continues.  
3
Select Single-area AF or Dynamic AF.  
Press the AE-L/AF-L button to  
lock the focus.  
2
Single-  
Area AF  
Predictive motion Only works for moving Also works for subjects that Does not operate.  
focusing subjects from the time AF start moving during shooting.  
(focus tracking operation starts. While this  
function for function is operating, the  
moving subjects) camera decides when the  
subject is in focus and  
Dynamic  
AF  
releases the shutter.  
CSM 9: AF operation can be modified so that it does not begin when the shutter button is  
pressed down halfway, but when the “AE-L/AF-L” button is pressed (P.111).  
The displays shown in the viewfinder and on the top display panel are shown  
below.  
Dynamic AF (Closest-  
subject Priority AF OFF)  
Dynamic AF (Closest-  
subject Priority AF ON)  
Single-area AF  
Focus area  
Top display panel/  
viewfinder display  
Then specify the focus area.  
End of settings.  
46  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOCUS SETTINGS  
FOCUS SETTINGS  
SELECTING THE FOCUS AREA  
MANUAL FOCUS  
Unlock the 4-direction button.  
Use Manual focus in situations where autofocus may not work as expected (P.39) or a lens other  
than an AF Nikkor lens (P.20) is attached.  
1
2
Focus the camera by turning the focusing ring on  
the lens until the image can be seen clearly in the  
matt surface of the viewfinder screen.  
h When using a lens with the A-M select function,  
set the switch/ring to “M” to focus manually. If  
M/A” (autofocus with manual priority) is available  
with your lens, Manual focus is possible either  
with the switch/ring set to “M” or “M/A”. See the  
instruction manual of your lens for details.  
1Press “d”, “c”, “a” or “b” to select the focus  
area.  
2Once you have specified the focus area, lock the  
4-direction button to prevent accidental improper  
use.  
01  
02  
Focus aid  
This allows you to check the focus of your shot  
using the focus indicator “” in the viewfinder.  
You can use Focus Aid when the lens mounted has  
an f-stop setting brighter than f/5.6.  
01  
h The specified focus area is automatically  
illuminated in red according to the brightness of  
the subject.  
1
1Position the selected focus area over the object  
on which you want to focus.  
2Turn the focusing ring on the lens.  
CSM 3: The specified focus area is automatically illuminated, but you can change the settings  
so that the illumination is disabled or is no longer dependent on the subject brightness  
(P.111).  
3
CSM 4: Normally, you can only select a focus area by pressing the arrow on the 4-direction  
button that points towards that focus area. However, you can set camera operation so  
that when the right-hand focus area is selected, pressing “c” on the 4-direction button  
selects the left-hand focus area. This means you can switch between focus areas on  
opposite sides without having to press different sides of the 4-direction button  
(P.111).  
02  
Press the shutter button down halfway. When the  
shot is in focus, the focus indicator “” lights.  
2
Focus indicator  
To make focusing easier on this camera, the range in which the focus indicator “” lights is set to a  
fixed size. As a result, the camera does not react to slight movements of the focusing ring, thereby  
avoiding flickering in the focus indicator “”.  
However, this means that the focusing position at the wide-angle setting is very slightly different from  
the focusing position at the telephoto setting, so that the shot may not be optimally focused even when  
the focus indicator “” is lit. In this situation, you can focus precisely by positioning the focusing ring in  
the middle of the range in which the focus indicator “” lights.  
48  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RELEASE MODES  
, SINGLE-FRAME /  
. CONTINUOUS SHOOTING  
RELEASE MODES  
9 SELF-TIMER PHOTOGRAPHY  
The release mode is normally set to Single-frame. Set the release mode to Continuous Shooting to  
take sequential shots of moving subjects or to take a series of shots using Auto Exposure  
Bracketing.  
You can use the self-timer when you want to be in the photograph. Use a tripod or place the camera  
on a stable surface before using the self-timer.  
Hold down the release mode switch unlock button  
Hold down the release mode switch unlock button  
and set the release mode switch to “,” (Single-  
frame) or “.” (Continuous Shooting).  
and set the release mode switch to “9” self-timer.  
1
Before shooting  
h The self timer does not operate in situations where the camera shutter is disabled, such as when the  
focus is not set in AF-S (Single-AF Servo) mode.  
h In exposure modes other than “M” (Manual), you must prevent any back-entry light from the eyepiece  
to obtain the correct exposure. Before pressing the shutter button, cover the eyepiece with your hand  
or the eyepiece cap provided. To attach the eyepiece cap, remove the rubber eyecup and slide the  
cap down over the eyepiece from above.  
SINGLE-FRAME  
,
In this mode, one shot is taken each time you press the shutter button. Use this mode to take a  
single clearly defined shot in each frame.  
h Do not stand in front of the lens when setting the self-timer in autofocus mode.  
!
If you take a number of single-frame shots in rapid succession, the number of available shots is highlighted in the same  
way as in continuous shooting. Once this happens, no further shots can be taken. Wait until the number of available shots  
is no longer highlighted.  
1Position the focus area over the subject.  
2Press the shutter button down halfway to focus  
01  
2
CONTINUOUS SHOOTING  
This mode allows you to take up to 12 consecutive shots by holding down the shutter button (Max.  
2.5 frames/sec.).  
.
3
the shot.  
3Without releasing the shutter button, press the  
shutter button down fully to start the self-timer.  
h Once you have shot the maximum number of continuous frames, the number of available shots  
shown on the rear display panel is highlighted. No further continuous shots can be taken at that  
point. Wait until the number of available shots is no longer highlighted.  
02  
03  
ISO200  
ISO200  
09 / 23 / 2004  
09 / 23 / 2004  
10 : 00 AM  
10 : 00 AM  
!
You cannot use continuous shooting with the built-in flash.  
The self-timer lamp flashes for 8 seconds and then  
stays lit for 2 seconds, after which the shot is taken.  
h Press the “MENU/OK”, “FUNC” or “PLAY” button  
to cancel self-timer shooting.  
!
If “ON” or “PREVIEW” is selected for “IMAGE DISP.” (P.103) when continuous shooting is used, only the photographed  
image for the final frame is displayed and automatically recorded.  
If you use continuous shooting when the number of available shots is low, the number of available shots may temporarily  
change to 0.  
3
!
h You can change the self-timer running time from  
10 seconds to 2, 5 or 20 seconds (P.112).  
The number of available frame and the maximum number of continuous frames varies depending  
on the dynamic range (D-RANGE) and quality settings in SET-UP.  
D-RANGE setting in SET-UP  
Quality  
WIDE  
FINE, NORMAL  
STANDARD  
FINE, NORMAL  
HIGH  
HIGH  
RAW  
RAW  
JPEG  
JPEG  
Max. number of available frames  
Max. continuous frames  
Max. 1.4 frames/sec.  
3
Max. 1 frame/sec.  
6
Max. 2.5 frames/sec.  
7
12  
Minimum shooting interval in  
multiple exposure shooting  
Max. 1.4 frames/sec.  
Max. 2.5 frames/sec.  
Max. no. of consecutive shots in  
multiple exposure shooting  
3
7
50  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RELEASE MODES  
p MULTIPLE EXPOSURE  
This is a photography technique that allows you overlay photographed images on top of each other.  
You can use this technique to compose shots that cannot be obtained normally.  
1When you compose, focus and take the shot, a  
preview image appears on the LCD monitor.  
2Press the “F2” button to move on to the next  
shot.  
01  
02  
3
4
Hold down the release mode switch unlock button  
and set the release mode switch to “p” (multiple  
1
h A preview image is always displayed, regardless  
of the “PREVIEW” setting selected in SET-UP.  
h If you change the release mode before multiple  
exposure shooting is completed, no images are  
recorded.  
exposure). When you select multiple exposure  
mode, the “p” icon appears in the viewfinder  
display.  
PREVIEW  
The settings for multiple exposure shooting can  
only be changed from the function menu. At this  
point, the last settings specified apply.  
When you take the next (multiple exposure) shot, a  
preview appears showing the overlaid images.  
h To record the image:  
Press the “F1” or “MENU/OK” button.  
h To take another multiple exposure shot:  
Press the “F2” button.  
h To take the shot again without using multiple  
exposure mode:  
According to the photography conditions, hold  
down the “b” (exposure compensation) button 1  
as you turn the Main-command dial 2 to set the  
exposure offset.  
2
01  
3
Press the shutter button again.  
h To cancel multiple exposure mode without  
recording the shots:  
PREVIEW  
Press the “F3” or “BACK” button.  
h To check the brightness distribution:  
Press the “F4” button.  
02  
F1 F2 F3 F4  
Standard compensation value in Multiple exposure  
In multiple exposure, a number of images are shot in the same frame. When you are overlaying  
backgrounds and subjects, you must set the appropriate exposure offset before taking any shots.  
CSM 11: In multiple exposure mode, one shot is taken in the frame each time the shutter button is  
pressed, but continuous shooting can also be used (P.111). Images in continuous  
shooting are overlapped in the preview display. Use the “F1”, “F3” and “F4” buttons. “K”  
cannot be selected in continuous shooting.  
General guide to exposure offsets  
h Test shooting is recommended since the  
compensation actually required varies depending  
on the shooting situation.  
h When the background is completely dark and  
subjects do not overlap, no compensation is  
necessary for each shot.  
Number of exposures Compensation value  
!
Multiple exposures cannot be used when only 1 frame is shot in continuous shooting.  
You cannot use the built-in flash for continuous shutter release.  
See P.50 for the max. no. of consecutive shots in multiple exposure shooting.  
2
3
4
!
!
52  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
METERING SYSTEMS  
ISO SENSITIVITY  
Normally, the Matrix metering system will provide the optimum exposure for your shot. However,  
you can choose from 3 metering modes for shots where you want to select a different exposure  
level (AE lock or exposure compensation) or for particular scenes (such as backlit shots or shots  
with very strong contrast).  
Set the Exposure mode dial to “ISO”.  
1
Turn the Metering system selector dial to desired  
metering system.  
The icon for the selected metering system appears  
in the viewfinder.  
Turn the Main-command dial to set the ISO  
sensitivity.  
2
h Available ISO sensitivity settings  
100, 160, 200 (factory default setting), 400, 800  
and 1600  
(
)
l Matrix 10-segment metering  
The camera sets the optimum exposure based on  
data (the maximum brightness and brightness  
contrast) measured independently for 10 segments  
in the photography screen.  
With D- or G-type Nikkor lenses, 10-segment 3-D  
matrix metering is used, factoring in the distance to  
the subject as well as the maximum brightness and  
brightness contrast to ensure even more accurate  
metering.  
ISO200  
!
If you shoot dimly lit scenes with a low sensitivity setting and  
without using the flash, the color tones for the entire image  
may be incorrect.  
3
09 / 23 / 2004  
10 : 00 AM  
Images shot in high-sensitivity photography (ISO  
400 or higher) may appear coarse and may also be  
affected by noise such as white dots.  
Center-weighted metering  
k
Center-weighted metering determines the exposure  
value based primarily on a 12-mm circle in the  
center of the viewfinder.  
Spot metering  
j
Spot metering determines the exposure value by  
concentrating metering on the equivalent of a 4-mm  
diameter area in the viewfinder (approx. 2% of the  
entire frame).  
The metering area moves to follow shifts in the  
selected focus area. However, spot metering  
always remains in the center of the shot when  
Closest-subject Priority Dynamic AF mode is used.  
54  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPOSURE MODES  
P AUTO-MULTI PROGRAM  
This mode automatically controls the shutter speed and aperture setting to give the optimum  
exposure for the photography conditions. This mode is useful when you want to be able to take  
pictures quickly and easily to take advantage of snapshot opportunities.  
Program chart  
The program chart shows exposure control in Auto-Multi Program mode (ISO 100).  
Set the Exposure mode dial to “P”.  
With AF 50 mm f/1.4D  
With AF 180 mm f/2.8D ED  
With AF-S 300 mm f/4D ED  
1
EV range: EV 0-21  
Compose picture, focus and shoot.  
2h When the subject is too dark or bright, one of the following warning indications will appear in  
Aperture  
the viewfinder or top display panel.  
i £: Use an ND filter.  
i ¢: Use the flash.  
Flexible Program  
Shutter speed  
h Limits apply to the upper and lower EV values depending on the metering range for the ISO  
sensitivity setting.  
h In Matrix metering, any EV above 16 1/3 is controlled to EV 16 1/3 when using ISO 100.  
Consequently, shots of very bright subjects may be overexposed.  
3
If you select the “P”, “S” or “A” exposure mode when you are not using a Nikkor lens with a built-in  
CPU, “§” appears on the top display panel and in the viewfinder and you cannot take pictures.  
When this occurs, you can take pictures by setting the exposure mode to “M” and using the aperture  
ring on the lens to set the aperture. Note that you cannot use the camera’s exposure meter.  
In Auto-Multi Program, by rotating the Main-command dial you can change the combination of shutter  
speed and aperture while maintaining correct exposure. With this function, you can shoot in Auto-Multi  
Program as though you were shooting in Shutter-Priority Auto or Aperture-Priority Auto. “W” appears in  
the top display panel when the Flexible Program is used. To cancel the Flexible Program, turn the  
Main-command dial until the Flexible Program icon “W” disappears, change the exposure mode, turn  
the Power switch to “OFF”, use the built-in flash (P.70), or perform a Two-Button Reset (P.109).  
56  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPOSURE MODES  
EXPOSURE MODES  
S SHUTTER-PRIORITY AUTO  
A APERTURE-PRIORITY AUTO  
In this mode, the photographer sets the shutter speed (1/4000 sec. to 30 sec.) and the camera  
automatically controls the aperture setting. This mode is best when the shutter speed takes priority,  
such as shots where a fast shutter speed is used to freeze the action or a slow shutter speed is  
used to convey the sense of movement.  
In this mode, the photographer sets the aperture (minimum aperture to maximum aperture) and the  
camera automatically controls the shutter speed. This mode is best for photographs where the  
priority is on the depth of field (the area where objects are in focus), such as shots where both near  
and distant objects are in clear focus (minimum apertures) or where the background is out of focus  
(maximum apertures).  
Set the Exposure mode dial to “S”.  
Set the Exposure mode dial to “A”.  
1
h If “” is selected in “M” Manual exposure  
mode and the exposure mode is changed to “S”  
Shutter-Priority Auto without cancelling “”,  
” blinks and the shutter locks. When this  
occurs, select a shutter speed other than  
”.  
1
Set the shutter speed (1/4000 sec. to 30 sec.) on  
the Main-command dial.  
Use the Sub-command dial to set the aperture  
(minimum aperture to maximum aperture).  
2
2
3
Images shot with long exposures (4 second or  
longer) may appear coarse and may also be  
affected by noise such as white dots.  
Compose picture, focus and shoot.  
Compose picture, focus and shoot.  
3h When the subject is too dark or bright, one of the following warning indications will appear in  
the top display panel or viewfinder (Electronic analog exposure display will also indicate the  
amount of under- or overexposure).  
3h When the subject is too dark or too bright, one of the following warning indications will appear  
in the top display panel or viewfinder (Electronic analog exposure display will also indicate the  
amount of under- or overexposure).  
i £: Select higher shutter speed. If the warning indication still remains on, use an ND filter.  
i ¢: Select a slower shutter speed. If the warning indication still remains on, use the flash.  
i £: Select smaller aperture (larger f-number). If the warning indication still remains on, use  
an ND filter.  
!
At slow shutter speeds (1/8 sec. or slower), the camera performs noise removal processing after the shutter closes.  
As a result, the access lamp may not light for several seconds, increasing the interval between shots.  
i ¢: Select larger aperture (smaller f-number). If the warning indication still remains on, use  
the flash.  
If you select the “P”, “S” or “A” exposure mode when you are not using a Nikkor lens with a built-in CPU,  
§” appears on the top display panel and in the viewfinder and you cannot take pictures.  
When this occurs, you can take pictures by setting the exposure mode to “M” and using the aperture  
If you select the “P”, “S” or “A” exposure mode when you are not using a Nikkor lens with a built-in CPU,  
§” appears on the top display panel and in the viewfinder and you cannot take pictures.  
When this occurs, you can take pictures by setting the exposure mode to “M” and using the aperture  
ring on the lens to set the aperture. Note that you cannot use the camera's exposure meter.  
ring on the lens to set the aperture. Note that you cannot use the camera's exposure meter.  
58  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPOSURE MODES  
M MANUAL  
In this mode, the photographer is free to set any shutter speed (1/4000 sec. to 30 sec. or “”)  
or aperture setting (narrowest aperture to widest aperture). This allows the photographer to  
determine the exposure to suit the conditions and the desired effect while watching the electronic  
analog exposure display in the viewfinder.  
Electronic analog exposure display  
The electronic analog exposure display in the viewfinder indicates the difference between the selected  
exposure (shutter speed and aperture) and the correct exposure. Not available with long time exposure.  
The electronic analog exposure display blinks when the subject brightness is beyond the camera’s  
exposure range.  
CSM 6: To use the “” shutter speed (for long exposures), the custom settings must be  
modified (P.111).  
The following examples show electronic analog exposure display indications:  
Correct exposure  
–1/2 EV  
Over +3 EV  
Set the Exposure mode dial to “M”.  
1
Compose picture, focus and shoot.  
3
If you are not using a Nikkor lens with a built-in CPU, you can take pictures by using the aperture ring  
on the lens to set the aperture. However, you cannot use the camera’s exposure meter. “§” also  
appears on the top display panel and in the viewfinder.  
(
)
Bulb photography ™  
Bulb photography is useful when you want to take pictures with any shutter speed. You should use  
a tripod to keep the camera steady because the shutter stays open for as long as the shutter button  
is held down.  
2
Images shot with long exposures (4 second or longer) may appear coarse and may also be affected by  
noise such as white dots.  
3
CSM 6: To use the “” shutter speed (for long  
01  
exposures), the custom settings must be  
modified (P.111).  
1
1Set the Exposure mode dial to “CSM”.  
2Use the Main-command dial to select “6. LONG  
EXP. (BULB) AT MANUAL MODE”.  
02  
03  
3Use the Sub-command dial to select “1:  
ACTIVATED”.  
USTOM ETTING  
6.LONG EXP.(BULB) T MAUAL   
  MODE  
While watching the electronic analog exposure display in the viewfinder, use the Main-command  
dial to set the shutter speed (1/4000 sec. to 30 sec. or “”) and the Sub-command dial to  
set the aperture setting (minimum aperture to maximum aperture).  
DISABLED  
ACATED  
h When the exposure compensation (P.63) is set, only the electronic analog exposure display  
changes—selected shutter speed and aperture do not change.  
MAIN  
NU  
SUB  
SETTING  
Images shot with long exposures (4 second or longer) may appear coarse and may also be  
affected by noise such as white dots.  
Continued  
60  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPOSURE MODES  
M MANUAL  
b EXPOSURE COMPENSATION  
Set the Exposure mode dial to “M”.  
Exposure compensation allows you to intentionally vary the optimum exposure value controlled by  
the camera. This can be useful when intentionally achieving under- or overexposure. Use Center-  
weighted or Spot metering. Exposure compensation can be performed in any exposure mode  
(However in “M” exposure mode, only the electronic analog exposure display changes—selected  
shutter speed and aperture do not change).  
2
3
h Bulb photography can only be used in Manual  
exposure mode.  
h A tripod should be used for bulb photography.  
Set exposure compensation by rotating the Main-  
command dial while pressing the “b” button until  
the desired compensation value appears (–3 EV to  
+3 EV in 1/2 EV steps).  
1
01  
1 Use the Main-command dial to set the shutter  
speed to “” and then 2 use the Sub-  
command dial to set the aperture setting (minimum  
aperture to maximum aperture).  
h When the exposure compensation is set, “d”  
appears on the top display panel and viewfinder.  
The Electronic analog exposure display also  
appears in the viewfinder. The compensation  
value can be checked by pressing the “b”  
button.  
h Electronic analog exposure display indicates the  
exposure compensation value and “0” blinks.  
h Normally, you should compensate exposure to  
the + side when the background is brighter than  
your main subject, or to the – side when the  
background is darker.  
02  
01  
02  
h See P.73 for information on using flash exposure  
compensation to adjust the amount of light  
emitted by the flash.  
Compose picture, focus and shoot.  
4h The shutter will be open as long as the shutter release button is kept fully depressed.  
h Using the cable release (sold separately) or remote release (sold separately) instead of  
holding the shutter release button down with your finger reduces camera shake.  
3
<Electronic analog exposure display>  
–0.5 EV compensation  
Remote Release Compatibility  
This camera can be used with 10-pin remote releases.  
Use the remote release (sold separately) with a tripod (sold separately) to prevent camera shake.  
Connect the remote release to the 10-pin terminal by matching the indicators on the terminal and  
accessory cord.  
Nikon accessories that can be used with the 10-pin terminal.  
i Remote Cord MC-20  
i Extension Cord MC-21  
i Remote Cord MC-22  
i Remote Cord MC-30  
i Luminosity Controller Set ML-3  
i Conversion Cord MC-25  
+2 EV compensation  
!
When not using the 10-pin terminal, always fit the terminal cap.  
Dust or soiling in the terminal can cause malfunctions.  
Compose picture, focus and shoot.  
!
If Auto Power Off has shut down the camera, the camera cannot be started up again from an accessory. (Use the  
custom settings to specify the delay until Auto Power Off shuts down the camera.)  
The Connection Cord MC-23 is not supported.  
If the camera loses power while you are using a cable release or directly holding down the shutter button, it cannot  
save the photographed image. If you are using a 10-pin remote-control cable, the image is saved at the point the  
batteries run out of charge.  
2h To cancel exposure compensation, set the compensation amount to “0.0” or perform a Two-  
!
Button Reset (P.109) (Turning the camera off does not cancel exposure compensation).  
!
!
Attach the bundled clamp filter when using the remote release  
(Secure the clamp filter by looping the cord through the filter at  
the connector end of the cord, as shown in the figure on the  
right).  
62  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
c AUTO EXPOSURE BRACKETING  
Use auto exposure bracketing when you want to take the same shot with different exposure  
settings. Using the correct exposure setting displayed by the camera (the value set in “M” exposure  
mode) as a reference, the camera can automatically offset the exposure by a set value (up to 2 EV  
steps without exposure compensation) in either direction.  
Compose picture, focus and shoot. A bracketing bar graph in the top display panel shows the  
photography status each time a shot is taken.  
3
h When three shots are to be taken, “  
appears after the first shot, “ ” appears after the second shot, and the bar graph  
disappears when shooting is completed.  
” is shown before shooting begins, “  
Hold down the “c” button 1 as you turn Main-  
command dial 2 to display the “Q” icon on the  
h If you hold the shutter button down when the “.” (Continuous shooting) release mode is  
selected, shooting automatically stops when the specified number of shots has been taken.  
Note that shots are taken one frame at a time when the built-in flash is used.  
h If the exposure compensation function (P.63) or flash exposure compensation (P.73) is  
also set, Auto Exposure Bracketing will be combined with the exposure compensation values.  
It is useful to perform Auto Exposure Bracketing with a compensated value of over +2 EV or  
under –2 EV.  
h To cancel the Auto Exposure Bracketing, rotate the Main-command dial while pressing the  
c” button so “Q” disappears from the top display panel or perform Two-Button Reset  
(P.109). The number of shots and compensated EV values previously selected will remain  
when they are cancelled with the Main-command dial, and they automatically reset to  
01  
02  
1
2
top display panel.  
h The “d” icon continues to flash while auto  
exposure bracketing is being used to indicate that  
auto exposure bracketing photography is in  
progress.  
” when the Two-Button Reset is performed.  
Hold down the “c” button 1 as you turn Sub-  
command dial 2 to set the number of shots (up to  
3) and the exposure offset (up to 2 EV steps in  
1/2 EV step increments).  
CSM 1: Bracketing order can be set to change from negative EV value to positive EV value  
(P.111).  
01  
02  
!
The Auto Exposure Bracketing settings are canceled when the live image is displayed. Wait until live image display is  
finished before specifying the Auto Exposure Bracketing settings.  
3
!
Check the number of available shots before setting the  
number of shot.  
List of exposure offsets and numbers of shots  
Number of shots and  
Bracketing bar graph  
compensated EV value  
Bracketing order  
0, –0.5, +0.5  
0, –1.0, +1.0  
0, –1.5, +1.5  
0, –2.0, +2.0  
0, +0.5  
0, +1.0  
0, +1.5  
0, +2.0  
0, –0.5  
0, –1.0  
0, –1.5  
0, –2.0  
64  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FLASH PHOTOGRAPHY  
FLASH PHOTOGRAPHY  
FLASH PHOTOGRAPHY  
BUILT-IN FLASH  
The built-in flash for FinePix S3 Pro camera covers the field of view of a 20 mm lens. It has a guide  
number of 12 (ISO 100-m) and is controlled using the dedicated TTL mode (D-TTL mode) that  
controls the monitor brightness. D-3D Multi BL flash control and D-Multi BL flash control can be  
used to take natural-looking photographs with the flash. In addition to shooting in dim light, the flash  
can be used in daylight to reduce shadows on the main subject or to put catchlights in your  
subject’s eyes. Five flash Synchro modes—Front Synchro (Normal Synchro), Slow Synchro, Rear  
Synchro, Red-Eye Reduction and Red-Eye Reduction with Slow Synchro—are available with  
FinePix S3 Pro camera.  
SETTINGS FOR FLASH PHOTOGRAPHY  
Some flash settings can be set directly:  
Synchro mode (the flash timing and shutter speed)  
Flash exposure compensation (flash brightness adjustment)  
Other settings are:  
Flash control mode (the system for measuring and adjusting the flash brightness)  
Flash control range (the effective range of the flash)  
Flash control modes that can be used with the built-in flash  
Lens  
TTL Auto Flash mode  
D-3D Multi-Sensor Balanced Fill-Flash1  
D-Multi-Sensor Balanced Fill-Flash1  
The basic settings for flash photography are explained on P.67 to P.73. If necessary, refer also to  
“NIKON FLASH UNITS THAT CAN BE USED” (P.74).  
D- or G-type Nikkor lens  
CPU Nikkor lens other than D/G- type  
(except AF Nikkor for F3AF)  
How the flash control mode is set  
All Nikkor lenses  
Standard D-TTL  
The three flash modes are D-3D-Multi BL, D-Multi BL and Standard D-TTL. One of these is selected  
based on the exposure mode, the metering system and the lens-flash combination.  
1 When built-in flash is used and the exposure mode is set to Manual or Spot metering is selected, Standard D-TTL Auto  
Flash mode automatically changes to Standard D-TTL Flash.  
“M” exposure mode?  
“Spot” metering system?  
Lens-flash  
combination selected.  
Yes  
No  
Yes  
No  
D-3D Multi-Sensor Balanced Fill-Flash  
D-3D Multi-Sensor Balanced Fill-Flash can be performed with a combination of the FinePix S3 Pro  
camera and D- or G-type Nikkor lens. Performs balanced (BL) metering that uses multi-pattern  
photometering information to provide a balance between the main subject of the shot and the  
background light.  
When you press the shutter button, the camera flash fires a monitoring flash just before the shutter  
opens. The camera then instantaneously monitors the reflections from each part of the image using  
the sensors in its 5-zone TTL auto flash control. This information is then further enhanced using the  
information on the subject distance provided by the lens and the camera then determines the flash  
brightness that will perfectly balance the subject and the background light.  
Standard D-TTL  
D-3D-Multi BL  
D-Multi BL  
Standard D-TTL  
3
To increase the effective range of the flash  
Item  
Measure  
h If you set the metering mode to Spot or the exposure mode to “M”, the built-in flash uses the  
Standard D-TTL flash control.  
Lens brightness  
Guide No.  
Use a brighter lens.  
Use a higher number.  
Widen the aperture.  
Increase the ISO setting.  
Aperture  
D-Multi-Sensor Balanced Fill-Flash  
ISO setting  
Multi-Sensor Balanced Fill-Flash, without the Distance Information added to the D-3D Multi-Sensor  
Balanced Fill-Flash, can be performed with a combination of the FinePix S3 Pro camera and CPU  
Nikkor lens other than D/G-type.  
D-3D Multi-Sensor Balanced Fill-Flash together with D-Multi-Sensor Balanced Fill-Flash is called  
Automatic Balanced Fill-Flash with TTL Multi Sensor.  
Standard D-TTL Flash  
Can be used with any type of Nikkor lens. In Standard D-TTL Flash, automatic flash output level  
compensation is not available. This means that, even though the main subject is correctly exposed,  
the background may not be. Standard D-TTL Flash is useful when you want to highlight the main  
subject or perform flash exposure compensation.  
66  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FLASH PHOTOGRAPHY  
SYNCHRO MODES AND THEIR FEATURES  
You can select any of 5 modes to suit the type of shot and the desired effect.  
ah REAR SYNCHRO MODE  
1Press the flash pop-up button to pop up the  
flash.  
Can be used in all exposure modes. In the “P” and  
A” exposure modes, a slow shutter speed is used.  
The flash fires just before the shutter closes. This  
mode is effective in capturing the subject's  
movement as a flow of light in a way that looks  
natural.  
01  
2Hold down the “v” button.  
3Turn the Main-command dial to select the  
synchro mode.  
The icon shown on the top display panel changes  
as shown below.  
!
Rear Synchro cannot be used with a studio flash system  
since the correct synchronization cannot be obtained.  
as RED-EYE REDUCTION MODE  
Can be used in all exposure modes.  
02  
03  
The red-eye reduction lamp lights for approx. 1 sec.  
before the flash fires in order to reduce the red-eye  
effect in photos of people or animals.  
!
When you are not using the flash, always keep it stowed  
away to prevent battery depletion.  
asg RED-EYE REDUCTION  
SLOW SYNCHRO MODE  
Front Synchro  
Red-eye  
Reduction  
Red-eye Reduction Slow Synchro  
Slow Synchro  
Rear Synchro  
Can be used in the “P” and “A” exposure modes.  
This mode combines red-eye reduction with a slow  
shutter speed.  
!
When some exposure mode and synchro mode combinations are selected, the synchro mode may be automatically  
changed subsequently.  
!
When a Nikon SB-80DX SB-28/28DX, SB-27 or SB-26 flash  
unit is used, the red-eye reduction lamp on the external flash  
fires.  
3
Exposure  
mode  
Display during Display after  
selection selection  
Synchro mode  
Rear Synchro  
Operation  
!
Take care to ensure that the camera and the subjects  
(people) in the shot do not move until the shutter is released.  
Depending on the type of lens mounted, the light from the  
red-eye reduction lamp may not reach the person, in which  
case the effect of the red-eye reduction lamp is lost.  
Automatically set to Slow  
Synchro.  
!
P or A  
Red-eye Reduction Slow  
Synchro  
Slow Synchro is cancelled  
(shutter speed not changed).  
S or M  
Shutter Speeds  
Slow Synchro  
The synchronized shutter speed is 1/180 sec.  
The shutter speeds that can be set vary depending on the combination of synchro mode and  
exposure mode, as shown below.  
Exposure mode  
a FRONT SYNCHRO MODE  
Can be used in all exposure modes.  
Select this mode for normal flash photography.  
P or A  
S
1/180 to 30 sec.  
M
Synchro mode  
1/180 to 1/60 sec.  
1/180 to 30 sec. and  
Z Front Synchro  
(automatically set by the camera1  
)
1/180 to 30 sec.  
X Slow Synchro  
C Rear Synchro  
(automatically set by the camera2  
)
Automatically set to Slow Synchro.  
1/180 to 30 sec.  
1/180 to 30 sec. and  
1/180 to 30 sec.  
(automatically set by the camera1 2  
)
ag SLOW SYNCHRO MODE  
1/180 to 1/60 sec.  
(automatically set by the camera)  
1/180 to 30 sec. and  
1/180 to 30 sec.  
V Red-eye Reduction  
Can be used in the “P” and “A” exposure modes.  
Because this mode uses a slow shutter speed, it  
captures the background while at the same time  
firing the flash to produce a shot that captures the  
atmosphere of a twilight or nighttime scene.  
1/180 to 30 sec.  
Red-eye Reduction  
(automatically set by the camera2  
)
B
Slow Synchro  
1 When a Nikon SB-26, SB-25 or SB-24 flash unit is used, the synchro selector on the external flash unit sets the  
shutter speed.  
2 Because a slow shutter speed is used, a tripod should be used to prevent camera shake.  
68  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FLASH PHOTOGRAPHY  
TAKING PICTURES USING THE BUILT-IN FLASH  
Operation described in this section applies when the built-in flash and D- or G-type AF Nikkor are  
attached.  
Exposure mode  
Shutter speed  
Aperture  
Flash control mode  
D-3D Multi BL  
P
S
Automatically set by the  
camera  
Synchronized shutter speed: 1/180  
sec. See P.69 for details.  
Set the metering system selector dial to “Matrix  
Center-weighted metering  
metering” or “Center-weighted metering”.  
1
A
M
Any aperture  
Standard D-TTL  
Shutter speeds faster than the synchronized speed (1/180 sec.) cannot be set. When “180” appears in the viewfinder  
display and the specified shutter speed flashes on the display panel, the actual shutter speed is 1/180 sec.  
The shooting distance is determined by the ISO setting and the aperture. For the “A” and “M” exposure modes, see the  
table below.  
For the “P” exposure mode, the maximum aperture that can be set by the camera varies depending on the ISO setting.  
See P.75.  
!
If you select “0” (Spot Metering), the flash control mode is  
switched to “Standard D-TTL”.  
Matrix metering  
ISO setting  
100  
160  
200  
400  
800  
1600  
1Press the flash pop-up button to pop up the  
flash.  
01  
Maximum aperture (built-in flash)  
2.8  
3.3  
3.3  
4
4.8  
5.6  
2
2Hold down the “v” button.  
3Turn the Main-command dial to select the  
synchro mode.  
Effective range of the built-in flash  
The effective range of the built-in flash varies depending on the ISO sensitivity and aperture settings  
used. Refer to the table below.  
Photography sensitivity (ISO) and aperture setting  
Metering range  
100  
1.4  
2
160  
1.8  
2.5  
3.5  
5
200  
2
400  
2.8  
4
800  
4
1600  
5.6  
8
2-8.5 m (6.6-27.9 ft.)  
1.4-6 m (4.6-19.7 ft.)  
1-4.2 m (3.3-13.8 ft.)  
0.7-3 m (2.3-9.8 ft.)  
0.6-2.1 m (2.0-6.9 ft.)  
0.6-1.5 m (2.0-4.9 ft.)  
0.6-1.1 m (2.0-3.6 ft.)  
0.6-0.8 m (2.0-2.6 ft.)  
2.8  
4
5.6  
8
02  
03  
2.8  
4
5.6  
8
11  
16  
22  
32  
5.6  
8
11  
16  
22  
32  
!
When you are not using the flash, always keep it stowed  
away to prevent battery depletion.  
3
5.6  
8
7.1  
10  
11  
16  
22  
32  
11  
16  
22  
11  
16  
14  
Set exposure mode and confirm shutter speed and  
aperture.  
20  
3
4
The minimum effective range for flash control using the built-in flash is 0.6 meters.  
Check that the “a” (ready light) is displayed in the  
viewfinder.  
!
If you take a number of continuous shots with the built-in  
flash, the “a” (ready light) may take a few moments to light.  
The shutter cannot be released unless “a” (ready light)  
appears without blinking in the viewfinder.  
!
Bear in mind the composition, focus and effective flash range when taking pictures.  
5 !  
If the “a” (ready light) flashes for about 3 seconds after the shutter is released, this is a warning that the flash fired at  
full power and the shot may be underexposed. Play the image back to check it. If you decide to retake the shot,  
check the shooting distance, aperture, flash control range, etc. again before shooting.  
If the subject is dark, the AF-assist illuminator fires to set the focus. See P.38 for details.  
When you use the flash, shots are not taken continuously when the release mode is set to Continuous Shooting.  
If the built-in flash is charging, camera-shake correction is not performed on a VR lens while the shutter button is  
pressed down halfway.  
!
!
!
70  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FLASH PHOTOGRAPHY  
FLASH PHOTOGRAPHY  
LENSES THAT CAN BE USED WITH THE BUILT-IN FLASH  
FLASH EXPOSURE COMPENSATION  
Flash exposure compensation lets you intentionally change the correct exposure computed by the  
flash and the camera. For example, you can highlight the main subject by increasing the flash output  
or prevent the main subject from becoming too bright by decreasing the flash output.  
Usable lenses with built-in flash  
h 20 mm to 300 mm CPU lenses can be used with the built-in flash.  
h To prevent vignetting, remove the lens hood when using the flash.  
h The built-in flash cannot be used at shooting distance less than 0.6 m (2.0 ft.).  
h Zoom lenses with a macro feature cannot be used in the macro range.  
h Vignetting occurs at the edges of the frame resulting in underexposure with the following zoom  
lenses, which have limitations in usable focal length or shooting distance:  
1Hold down the “n” button.  
2Turn the Main-command dial to set the amount  
of compensation.  
The “f” icon appears on the top display panel  
1
01  
Lens  
AF-S 17-35 mm f/2.8 ED  
AF 20-35 mm f/2.8  
Limitations  
and on the viewfinder.  
24 mm focal length at 0.8 m (2.6 ft.) or longer shooting distance  
20 mm focal length at 1 m (3.3 ft.) or longer shooting distance  
Compensation range: –3 EV to +1 EV in 1/2 EV  
increments  
28 mm focal length at 2 m (6.6 ft.) or longer shooting distance or 35 mm focal  
length at 0.7 m (2.3 ft.) or longer shooting distance  
Compensation guide: Select + settings when the  
background is brighter than  
AF 28-70 mm f/2.8 ED  
the subject and – settings  
when background is darker.  
20 mm to 200 mm non-CPU Nikkor lenses (AI-S, AI, AI-modified Nikkor) and Series-E lenses can be used with the built-in  
Flash. However following lenses have limitations in usable focal length or shooting distance:  
Ai’d. 50-300mm f/4.5 (can be used at 200mm), Ai 50-300mm f/4.5 (can be used at 200mm), Ai’d. 85-250mm f/4 (can be  
used at 135mm and above), Ai ED 50-300mm f/4.5 (can be used at 135mm and above), Ai-S ED 50-300mm f/4.5 (can be  
used at 135mm and above)  
02  
Notes on using the built-in flash  
h When the built-in flash is used, continuous shooting is not available even when the release mode  
is set to “.” (continuous shooting).  
h If the built-in flash is charging, camera-shake correction is not performed on a VR lens while the  
shutter button is pressed down halfway.  
The remainder of the procedure is the same as for normal flash photography (P.70).  
2
To check the amount of compensation  
3
Press the “n” button.  
Sample flash exposure compensation displays  
Compensation amount  
Top display panel  
Viewfinder display  
“0.0”  
“+0.5”  
“–0.5”  
To cancel exposure compensation  
h Set the compensation amount back to “0.0”.  
!
Turning the camera off does not cancel flash exposure compensation.  
72  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FLASH PHOTOGRAPHY  
NIKON FLASH UNITS THAT CAN BE USED  
Notes on using Nikon flash units  
The Nikon flash models listed in the table below can be used with this camera. In the table, 1  
indicates D- or G-type Nikkor lenses (except IX-Nikkor), 2 indicates CPU Nikkor lens other than D-  
or G-type (except AF Nikkor for F3AF) and 3 indicates non-CPU Nikkor lenses.  
h Refer to the instructions supplied with the flash unit for details.  
If the instructions provided with a D-TTL-capable Nikon flash unit (sold separately) include a  
camera model chart, read the section on digital SLR cameras.  
D-TTL  
Multi-  
AA  
Aperture-linked  
A
M
h The synchronized shutter speed when a flash is used is a slow speed of 1/180 sec. or slower.  
h The operating range of shooting sensitivities in D-TTL mode is ISO 100-1600.  
h With the SB-26, SB-25 and SB-24, the setting on the flash unit takes priority in Rear Synchro  
mode. (Note that this does not apply when “Red-eye reduction” or “Red-eye Reduction Slow  
Synchro” mode is selected on the camera.)  
h If you set the camera’s synchro mode to “Red-eye Reduction” or “Red-eye Reduction Slow  
Synchro” and then use a Nikon external flash unit that has its own red-eye reduction function, the  
red-eye reduction lamp on the external flash unit fires.  
h Even when the optional flash with the AF-assist illuminator is attached, AF-assist illuminator does  
not emit light unless the conditions for AF-assist illumination are met.  
h With SK-6 and SB-24 are attached, AF-assist illuminators of the camera body and the flash do not  
emit light.  
3D Multi-  
Sensor  
Flash  
Lens  
Sensor Standard automatic flash Non-TTL  
Repeating  
Flash  
Rear  
Red-Eye  
Manual  
Balanced Balanced TTL Flash brightness  
Fill-Flash Fill-Flash  
Auto  
Synchro Reduction  
control  
1  
1  
1  
2  
2  
1
2
3
1
2
3
1
2
3
SB-28DX  
1  
1  
1  
SB-80DX  
SB-800  
2  
2  
SB-50DX  
SB-600  
2  
2  
h When the exposure mode is “P” Multi-Programmed Auto, the widest aperture that can be  
automatically set by the camera is governed by the ISO setting used, as shown in the table below.  
With the Nikon flash units listed below, use external automatic flash control (A) or manual flash  
photography. Setting the mode to TTL locks the camera’s shutter button so that no shots can be  
taken. In the table, 1 indicates D- or G-type Nikkor lenses (except IX-Nikkor), 2 indicates CPU  
Nikkor lens other than D- or G-type (except AF Nikkor for F3AF) and 3 indicates non-CPU Nikkor  
lenses.  
ISO setting  
100  
160  
200  
400  
800  
1600  
Maximum aperture (optional flash)  
4
4.8  
4.8  
5.6  
6.7  
8
If an aperture that is wider than the controlled aperture is still too dark, the aperture is determined by widest aperture on  
the mounted lens.  
: Compatible  
A
M
h In D-TTL mode, if you use the TTL Sync Extension Cord SC-17 to operate the flash remotely from  
the camera, you may not obtain the correct exposure in D-TTL modes other than standard D-TTL  
flash control. If this happens, switch to standard D-TTL flash control. You should also take a test  
shot beforehand.  
h Do not fit attachments (such as a diffuser panel) other than the built-in panel to the front of the  
flash in D-TTL mode. This causes errors in the camera’s internal calculations and may result in  
the image being incorrectly exposed.  
1 Select metering system other than  
Spot.  
2 Set the photometering mode to spot  
metering.  
Flash  
Lens  
Non-TTL  
Auto  
Repeating  
Flash  
Rear  
Red-Eye  
Manual  
3
Synchro Reduction  
1
2
3
1
2
3
1
2
3
SB-28  
SB-26 3  
3 The SB-26 operates in slave mode. If  
the wireless slave selector is set to D,  
the camera’s shutter is automatically  
switched to a slower speed than  
1/180 sec.  
4 When used with the SB-27, the  
camera is automatically set to TTL  
mode. However, because the SB-27  
cannot be used in TTL mode, reset  
the SB-27 to forced A mode.  
SB-27 4  
h TTL multi-flash photography is not possible in D-TTL mode.  
SB-25  
SB-24  
Flash attachments made by manufacturers other than Nikon  
Use only Nikon flash models. Other units may damage the FinePix S3 Pro camera’s electrical circuit  
due to incompatible voltage requirements (not compatible with 40V or higher), electric contact  
alignment or switch phase.  
5 Not recommended as these are only  
for manual flash photography.  
1
2
3
SB-23 5  
SB-29 6, 5  
SB-21B 6, 5  
SB-29s 6, 5  
6 When the SB-29s, SB-29 or SB-21B  
is used, autofocus shooting is only  
possible when an AF micro lens  
(60mm, 105mm, 200mm or 70-  
180mm) is mounted.  
7 To use AF mode or M mode with the  
SB-11 or SB-14, use the SU-2 on the  
SC-13 at the same time with the  
respective connections. The SB-11  
and SB-14 can also be used  
connected to the SC-11 or SC-15,  
but in this configuration the ready  
light inside the camera’s viewfinder  
cannot be used and the shutter  
speed is not automatically switched.  
Accessory shoe (with cover)  
SB-30  
SB-22s  
SB-22  
SB-20  
SB-16B  
SB-15  
1
2
3
An optional flash, i.e. SB-80DX, 800, 600, 50DX, 27, 23, 22s or 29s can be attached directly to the  
accessory shoe of the FinePix S3 Pro camera without a cord. This accessory shoe is equipped with  
a safetylock which prevents accidental drop when a flash with a safety-lock pin (i.e. SB-80DX or 27)  
is attached.  
1
2
3
!
Always install the accessory shoe cover when you are not using an external flash unit.  
SB-11 7  
SB-14 7  
Synchronizing terminal (with cap)  
To use an external flash unit that requires a synchro cord, connect the synchro cord to the synchro  
cord terminal (with JIS-B locking screw).  
!
Always fit the terminal cap when the sync terminal is not being used.  
74  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PHOTOGRAPHY FUNCTION MENU  
PHOTOGRAPHY FUNCTION MENU  
USING THE FUNCTION MENU WHEN TAKING PICTURES  
WHITE BALANCE  
You can use the Function menu to change the quality settings (White Balance, Quality, Resolution,  
Film simulation, Dynamic range, Color, Tone, Sharpness) of saved images and the AF area  
settings.  
ISO200  
Turn the camera on and set the camera to Photography mode. If the Auto Power Off function  
has turned the camera off, press the shutter button down halfway to turn it back on.  
09 / 23 / 2004  
10 : 00 AM  
1
Press the “FUNC”  
button to switch  
between functions.  
The functions change each time the  
“FUNC” button is pressed.  
2
White balance  
ISO200  
09 / 23 / 2004  
10 : 00 AM  
WHITE BALANCE  
Change the settings when you want to set the white balance to suit the natural or artificial lighting  
conditions when you shoot.  
When AUTO is selected, the correct white balance sometimes cannot be obtained under special  
light sources or for subjects where people’s faces are highlighted, etc. In such cases, select the  
correct white balance setting for the light source.  
h Factory default setting:  
AUTO  
Display  
Name  
Description  
3
The camera automatically determines the amount of light and the color information for the  
shot and takes the picture with a natural white balance.  
AUTO  
Custom 1  
Custom 2  
Fine  
This setting uses the white balance setting specified by the photographer in the “SET-UP”  
menu (P.104).  
Method 1  
3
Select this setting for outdoor shots in fine weather when the light source for the shot is the  
sun.  
The setting changes each time you press the button.  
Shade  
Select this setting for shots taken in shade or on cloudy days.  
Fluorescent 1 Select this setting for shots taken under “Daylight” fluorescent lamps.  
Fluorescent 2 Select this setting for shots taken under “Warm White” fluorescent lamps.  
Fluorescent 3 Select this setting for shots taken under “Cool White” fluorescent lamps.  
Incandescent Select this setting for shots when the light source is incandescent bulbs or lights.  
Method 2  
The settings can be changed by holding down the  
button and pressing “a” or “b”.  
h When the flash fires, the white balance setting (excluding custom white balance) for the flash is used.  
Consequently, to achieve a particular effect, the flash mode should be set to Suppressed flash.  
76  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PHOTOGRAPHY FUNCTION MENU  
QUALITY / RECORDED PIXELS / FILM SIMULATION  
RECORDED PIXELS  
Sets the size of the photographed image.  
h Factory default setting:  
3024×2016  
ISO200  
09 / 23 / 2004  
10 : 00 AM  
Display  
Name  
Description  
Sets the image size to 1440 × 960 pixels (approx. 1.38 megapixels).  
You can record the largest number of images in this mode.  
1M  
Press the “FUNC”  
button to switch  
between functions.  
Sets the image size to 2304 × 1536 pixels (approx. 3.54 megapixels).  
Sets the image size to 3024 × 2016 pixels (approx. 6.10 megapixels).  
3M  
6M  
Quality  
Film simulation  
Recorded pixels  
Sets the image size to 4256 × 2848 pixels (approx. 12.10 megapixels).  
You can record the fewest images in this mode.  
12M  
QUALITY  
h You cannot set the image size when the quality is set to “HIGH”.  
Sets the quality of the photographed image. Select settings suited to the purposes for which the  
photograph will be used.  
Select “FINE” for better quality or “HIGH” to shoot CCD-RAW images.  
The “NORMAL” setting provides ample image quality for most purposes.  
Guide to printed image sizes  
Name  
Description  
Printing at up to 3R (8.9 × 12.7 cm/3.5 × 5 in.) size  
1M  
h Factory default setting:  
NORMAL  
3
Display  
Name  
Description  
Printing at up to 6R (15.2 × 20.3 cm/6 × 8 in.) / A5 size  
Printing at up to 10R (25.4 × 30.5 cm/10 × 12 in.) / A4 size  
Printing at up to 35.6 × 43.2 cm (14 × 17 in.) / A3 size  
3M  
6M  
NORMAL  
Allows you to record the largest number of images.  
12M  
Records images in high quality bettered only by the “High” setting. This mode allows you  
to record more images than the “High” setting.  
FINE  
HIGH  
FILM SIMULATION  
Sets the image formation parameters for photographed images.  
CCD-RAW (P.140): No image processing is performed on the camera. Select this setting  
when you want to process the image on a PC.  
h Factory default setting:  
STANDARD  
Display  
Name  
Description  
Shooting CCD-RAW images  
Because CCD-RAW images are not processed in the camera, the bundled software or the optional  
Hyper-Utility Software HS-V2 (P.123) must be used to process the images on a PC.  
This is the standard image composition mode and is ideal for a wide range of subjects,  
including portraits and scenery.  
STANDARD  
h To shoot CCD-RAW images, set the quality to “HIGH”. The image size setting automatically changes  
to “RAW” and cannot be changed.  
FILM  
This mode suppresses flaring in flash highlights when the flash is used and also stresses  
SIMULATION smooth tonal transitions in the reproduction of skin tones. It is ideal for studio portrait work  
F1  
where the aim is professional-standard negatives.  
!
When you display a CCD-RAW image, the frame number is highlighted.  
FILM  
SIMULATION  
F2  
This mode provides vibrant reproduction of natural colors such as blue skies and is ideal  
for landscape and nature photography.  
h If you want to change this setting, select “sRGB” as the color space and “WIDE” as the “D-  
RANGE” (Dynamic range) setting in SET-UP.  
78  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PHOTOGRAPHY FUNCTION MENU  
DYNAMIC RANGE / COLOR / TONE / SHARPNESS  
TONE  
ISO200  
Use the procedure below to set the contrast when images are shot.  
09 / 23 / 2004  
10 : 00 AM  
h Factory default setting:  
STD  
Display  
Name  
Description  
STD  
(STANDARD)  
This setting sets the contrast for photographed images to the standard level.  
This setting provides a higher level of contrast than the “STD” setting.  
Press the “FUNC”  
button to switch  
between functions.  
HARD  
This setting specifies a lower contrast than the “STD” setting.  
Use this setting for images that will undergo image processing for use in commercial  
printing.  
ORG  
(ORIGINAL)  
Dynamic range  
Sharpness  
Color  
Tone  
h If you want to view or print the image data directly, do not select “ORG”.  
DYNAMIC RANGE  
Sets the dynamic range used for photographed images.  
SHARPNESS  
Use this setting to soften or sharpen the outlines in an image and to adjust the quality of the  
photographed image.  
h Factory default setting: AUTO  
Display  
Name  
Description  
h Factory default setting:  
STD  
The camera automatically varies the dynamic range between 100% and 400% according  
to the scene being shot before taking the picture. This mode suppresses white flaring and  
black patches in scenes with high contrast while also enabling you to achieve good levels  
of contrast in pictures taken indoors or in cloudy weather where a wide dynamic range is  
not needed.  
Display  
Name  
Description  
AUTO  
3
STD  
(STANDARD)  
This setting applies the optimum level of sharpness for normal shots.  
This setting sharpens the outlines in an image and is best for images of subjects such as  
buildings or text where clarity is important.  
WIDE 1  
WIDE 2  
Takes the picture with the dynamic range set to 230% regardless of the scene being shot.  
Takes the picture with the dynamic range set to 400% regardless of the scene being shot.  
HARD  
OFF  
Sharpness processing is not applied in this setting. Use this setting for images that will  
undergo image processing for use in commercial printing.  
h
If you want to change this setting, select “WIDE” as the “D-RANGE” (Dynamic range) setting in SET-UP.  
h If you want to view or print the image data directly, do not select “OFF”.  
The dynamic range, color, tone and sharpness cannot be changed  
COLOR  
Selecting “F1” or “F2” as the film simulation setting (P.79) prevents  
these settings from being changed. Select “STD” as the film  
simulation setting.  
Use the procedure below to set the density of the color used when images are shot.  
FILM SIMULATION F1  
h Factory default setting: STD  
Display  
Name  
Description  
STD  
(STANDARD)  
This setting sets the standard color density.  
FILM SIMULATION F2  
HIGH  
ORG  
This setting provides a higher color density than the “STD” setting.  
This setting specifies a lower color density than the “STD” setting. Use this setting for  
(ORIGINAL) images that will undergo image processing for use in commercial printing.  
B/W  
This setting converts the colors in the photographed image to black and white.  
h If you want to view or print the image data directly, do not select “ORG”.  
80  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PHOTOGRAPHY FUNCTION MENU  
AF AREA / FUNCTION LOCK / FUNCTION RESET  
FUNCTION RESET  
This resets the photography function menu options to their factory default settings.  
Press the “F4” button to display the reset  
confirmation screen.  
ISO200  
1
2
09 / 23 / 2004  
0 : 00 AM  
Press the “FUNC”  
button to switch  
between functions.  
The following operations can be used in the reset  
confirmation screen:  
To reset the menu: “H” (“F1” button)  
To return to the previous screen: “J” (“F4” button)  
RESET FUNCTION  
AF area  
Function lock  
Function reset  
AF AREA  
Auto Focus provides two AF modes. In Single-area AF mode, the shot is focused using the selected  
focus area, while in Dynamic AF mode, multiple focus areas are used to set the focus. See P.47 for  
more detailed information on the AF area modes.  
Reset  
Back  
h Factory default setting:  
Single-area AF  
Viewfinder,  
Top panel display  
Display  
Name  
Focus area  
Description  
3
Single-area  
AF  
Useful for situations where you want to focus  
accurately on a more or less stationary subject.  
Useful for shots where it is difficult to accurately  
keep the subject in a given focus area, such as  
when you are tracking a moving subject  
(P.47).  
Dynamic AF  
or  
or  
FUNCTION LOCK  
This feature allows you to lock the function menu settings so that they cannot be changed (to  
prevent accidental improper use).  
h Factory default setting:  
OFF  
Display  
Name  
Description  
OFF  
Releases the function lock.  
Sets the function lock.  
The settings cannot be changed once the function lock is  
applied. To change the settings, first press the “F2” button to  
cancel function lock.  
ON  
82  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK FUNCTION MENU  
Advanced  
PLAYBACK FUNCTION MENU  
4
Features Playback  
USING THE FUNCTION MENU  
HISTOGRAM  
You can use this menu to work with a displayed image (histogram display, erase, protect) and  
switch between multi-frame and single-frame playback.  
Unlock the 4-direction button 1 and press “d” or  
c2 to select the frame for which the histogram  
is to be displayed.  
01  
02  
1
2
Turn the camera on and press the “PLAY” button to select Playback mode. If the Auto Power  
1
Off function has turned the camera off, press the shutter button down halfway to turn it back  
on.  
The functions change each time the  
“FUNC” button is pressed.  
2
The histogram display changes each time you  
press the “F1” button.  
Histograms can be displayed for both playback  
images and preview images.  
100-0001  
100-0001  
: Image histogram for brightness shown.  
: Image histogram for red shown.  
: Image histogram for green shown.  
: Image histogram for blue shown.  
100-0001  
: Uses blinking black to display areas of white  
flaring (Brightness warning).  
09 / 23 / 2004 10 : 00 AM  
WB:AUTO NORMAL 6M F:STD  
Brightness warning: When the image is  
overexposed, areas where white blooming has  
occurred flash black.  
100-0001  
Brightness warning  
100-0001  
125 F5.6 ISO200  
D:AUTO C:STD T:STD S:STD  
!
The brightness warnings displayed during playback and  
during photographed image checking may differ.  
If “G” does not appear on the rear display panel, press the  
“FUNC” button to change the screen.  
!
!
A histogram is a graph that shows the distribution of  
brightness in an image.  
4
About the histogram display  
3
Histogram  
Even distribution  
Sloping up to the right  
Sloping up to the left  
The histogram display changes each  
time you press the button.  
Icon  
Mode  
Brightness  
Single-frame erase  
Shadows  
Highlights  
Erases an image.  
MASTER  
brightness  
Correct exposure  
Overexposed  
Underexposed  
Protect frame  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
Protects or unprotects an image.  
3
Multi-frame playback  
The mode switches between single-  
frame and multi-frame playback each  
time you press the button.  
84  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK FUNCTION MENU  
PLAYBACK FUNCTION MENU  
ERASING SINGLE-FRAME  
SINGLE-FRAME PROTECT  
Unlock the 4-direction button.  
Unlock the 4-direction button.  
1
2
3
1
2
3
Protection is a setting that prevents frames (files)  
from being accidentally erased. However, the  
“FORMAT” function erases all the frames (files),  
including protected frames (files) (P.106).  
Erased frames (files) cannot be recovered. Back up  
important frames (files) onto your computer or  
another media.  
Press the “F2” button to display the erase  
confirmation screen.  
Press the “F3” button to display the protection  
screen.  
100-0001  
100-0001  
!
If “F” does not appear on the rear display panel, press the  
“FUNC” button to change the screen.  
!
If “S” does not appear on the rear display panel, press the  
“FUNC” button to change the screen.  
!
If the currently displayed frame is protected, “'” appears  
instead of “F” and the “S” icon is displayed in the top-right  
corner of the LCD monitor.  
!
If the currently displayed frame is protected, “D” is displayed  
instead of “S”.  
The following operations can be used in the erase  
confirmation screen:  
To select the frame: “d” or “c”  
To erase the displayed frame: “H” (“F4” button)  
To return to the previous frame:  
The following operations can be used in the  
protection screen:  
To select the frame: “d” or “c”  
To protect the frame: “L” (“F1” button)  
To unprotect the frame: “:” (“F4” button)  
To return to the previous frame: “BACK” button  
next frame  
next frame  
last frame  
100-0001  
100-0001  
J” (“F1” button) or “BACK” button  
last frame  
Protect  
unprotect  
back  
delete  
!
1” displayed for a frame indicates that the  
back  
frame is protected. Unprotect the frame before erasing it.  
If “4” appears, press the  
H” (“F4” button) to erase the frames (files).  
4
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
To check protected frames  
4
Rear display panel  
(protection screen)  
Rear display panel  
(during single-frame playback)  
LCD monitor  
100-0001  
100-0001  
Protected  
100-0001  
100-0001  
Not protected  
No icon  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
4
86  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK FUNCTION MENU  
PLAYBACK MENU  
MULTI-FRAME PLAYBACK  
o ERASING ALL FRAMES  
Unlock the 4-direction button.  
1Press the “PLAY” button to select Playback  
mode.  
2Unlock the 4-direction button.  
01  
02  
1
2
3
4
5
1
2
Erased frames (files) cannot be recovered. Back up  
important frames (files) onto your computer or  
another media.  
Press the “F4” button.  
1Press the “MENU/OK” button to display the  
menu screen.  
2Press “d” or “c” to select “o” ERASE.  
01  
02  
Single-frame  
playback  
100-0001  
ALL FRAMES  
Erases all unprotected frames (files).  
Back up important frames (files) onto your computer  
or another media.  
Multi-frame  
playback  
RASE  
!
If “A” does not appear on the rear display panel, press the  
“FUNC” button to change the screen.  
AL RAMES  
CK  
Press “d”, “c”, “a” or “b” to move the cursor (the  
orange frame) and select a frame. Press “a” or “b”  
several times to move to the next or previous page.  
\ BACK  
Returns to playback without erasing any frames  
(files).  
1Press “a” or “b” to select “ALL FRAMES”.  
2Press the “MENU/OK” button.  
01  
02  
3
You can view the selected image enlarged by  
pressing the “F4” button again.  
100-0001  
ERE  
4
LL S  
CK  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
Continued  
88  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK MENU  
PLAYBACK MENU  
o ERASING ALL FRAMES  
i PROTECTING IMAGES: SET ALL / RESET ALL  
1Press the “PLAY” button to select Playback  
mode.  
2Unlock the 4-direction button.  
ALL FRAMES  
Pressing the “MENU/OK” button erases all the  
frames (files).  
01  
02  
1
 S  
 
ERASE ALL OK?  
Protection is a setting that prevents frames (files)  
from being accidentally erased. However, the  
“FORMAT” function erases all the frames (files),  
including protected frames (files) (P.106).  
IT MAY TAKE A WHILE   
NCEL  
S  
!
Protected frames (files) cannot be erased. Unprotect the  
frames (files) before erasing them (P.87).  
1Press the “MENU/OK” button to display the  
menu on the screen.  
2Press “d” or “c” to select “i” PROTECT.  
If “4” or  
01  
02  
2
5” appears, press the  
“MENU/OK” button again to erase the frames (files).  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
RESET ALL  
Removes the protection from all the frames (files).  
4
ROTECT  
RE ALL  
SE L  
SET ALL  
Protects all the frames (files).  
To stop the procedure midway  
1Press “a” or “b” to select “SET ALL” or “RESET  
ALL”.  
2Press “MENU/OK” button to confirm your  
selection.  
01  
02  
Press the “BACK” button to cancel erasing of all the  
frames (files). Some unprotected frames (files) will be  
left unerased.  
3
ALL FRAMES  
ROTECT  
4
!
Even if you stop the procedure immediately, some frames  
(files) will be erased.  
CANCEL  
RE ALL  
SE L  
Continued  
90  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK MENU  
PLAYBACK MENU  
(
)
i PROTECTING IMAGES: SET ALL / RESET ALL  
u HOW TO SPECIFY PRINT OPTIONS DPOF  
DPOF stands for Digital Print Order Format and refers to a format that is used for  
recording printing specifications for images shot using a digital camera on media such as  
an xD-Picture Card and CF/Microdrive. The recorded specifications include information  
on which frames are to be printed.  
SET ALL  
 L  
Press the “MENU/OK” button to protect all the  
frames (files).  
  ?  
This section gives a detailed description of how to order your prints with the FinePix S3  
Pro.  
    E  
NCEL  
YES  
Note that some printers do not support date and time imprinting or specification of the  
number of prints.  
Note that the warnings shown below may be displayed while you are specifying the  
prints.  
4
5
(P.86, 90)  
RESET ALL  
Press the “MENU/OK” button to unprotect all the  
frames (files).  
When erasing the image, the DPOF setting for that image is deleted at the same time.  
 L  
6
(P.94)  
  ?  
When inserting a media that contains images specified for printing on by another  
camera, those print specifications are all reset and replaced by the new print  
specifications.  
IT MAY TAKE A WHILE  
CANCEL  
YES  
u
(P.134)  
Up to 999 images can be specified on the same media.  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
4
4
To stop the procedure midway  
If the images are very large, protecting or  
unprotecting all the frames (files) may take some  
time.  
 L  
If you want to take a picture during the procedure,  
press the “BACK” button. To then return to protecting  
or unprotecting all the frames (files), start the  
procedure on P.91 from step 1.  
NCEL  
92  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK MENU  
u DPOF SET FRAME  
1Press the “PLAY” button to select Playback  
mode.  
2Unlock the 4-direction button.  
3Press the “MENU/OK” button to display the  
menu screen.  
1Press “d” or “c” to display the frame (file) for  
which you want to specify DPOF settings.  
2Press “a” or “b” to set a value up to 99 as the  
number of copies of the frame (file) to be printed.  
For frames (files) that you do not want printed,  
set the number of prints to 0 (zero).  
01  
02  
01  
02  
1
2
3
4
03  
POF:0011  
1 SHEETS  
To specify more DPOF settings, repeat steps 1  
and 2.  
Total number  
of prints  
!
Prints of up to 999 image frames (files) can be ordered on the  
same media .  
Setting for  
that frame  
!
DPOF settings cannot be specified for CCD-RAW.  
T  
E  
Pressing the “BACK” button while choosing settings  
will cancel all current settings. If there were  
previous DPOF settings, only the modifications are  
cancelled.  
Press “d” or “c” to select “u” DPOF.  
Always press the “MENU/OK” button after the  
settings are completed.  
Pressing the “BACK” button cancels those settings.  
5
6
u” appears on the  
LCD monitor during  
playback when the  
image has specified  
with DPOF setting.  
DPOF  
Canceling a frame  
 L  
To cancel the DPOF setting for a frame (file) you  
have specified (cancel frame), perform steps 1 to 3  
and then:  
1Press “d” or “c” to select the frame (file) with  
the DPOF setting you want to cancel.  
2Set the number of prints to 0(zero).  
To cancel the DPOF setting for another frame (file),  
repeat steps 1 and 2.  
UT E  
WITH DATE  
DPOF  
TO /   11SHEETS  
Total number of prints  
1Press “a” or “b” to select “WITH DATE” or  
“WITHOUT DATE”. Selecting “WITH DATE” will  
cause the date to be imprinted on your prints.  
2Press the “MENU/OK” button.  
Press the “MENU/OK” button to complete the  
settings.  
01  
02  
4
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
DPOF  
 L  
UT E  
WITH DATE  
!
When selecting the “WITH DATE” setting, the date is  
imprinted on your shots using the Print Service or a DPOF-  
compatible printer (depending on the printer specifications,  
the date may not be printed in some cases).  
When DPOF settings were specified on another camera  
When the data includes a frame (file) with DPOF  
settings that were specified on another camera,  
6” appears.  
Pressing the “MENU/OK” button erases all of the  
DPOF settings already specified for each frame (file).  
Specify the DPOF setting for each frame (file) again.  
 PO ?  
!
Press the “BACK” button to leave the previous settings  
unchanged.  
NO  
YES  
94  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK MENU  
PLAYBACK MENU  
(
)
u DPOF RESET ALL  
[ AUTOMATIC PLAYBACK  
1Press the “PLAY” button to select Playback  
mode.  
2Unlock the 4-direction button.  
3Press the “MENU/OK” button to display the  
menu screen.  
1Press the “PLAY” button to select Playback  
mode.  
2Unlock the 4-direction button.  
3Press the “MENU/OK” button to display the  
menu screen.  
01  
02  
01  
02  
1
2
3
4
1
2
3
4
03  
03  
1Press “d” or “c” to select “u” DPOF.  
Press “a” or “b” to select “RESET ALL”.  
2Press the “MENU/OK” button.  
Press “d” or “c” to select “[” PLAYBACK.  
01  
02  
OF  
PLAYBACK  
RESET ALL  
WITHOUT DATE  
WITH DATE  
A message appears.  
To reset all the DPOF settings, press the  
“MENU/OK” button.  
1Press “a” or “b” to select the playback interval  
and the type of image transition.  
2Press the “MENU/OK” button. The image frames  
are advanced and played back.  
01  
02  
4
To interrupt PLAYBACK, press the “F1” button.  
 PO ?  
NCEL  
PLAYBACK  
YES  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
96  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK MENU  
] TRIMMING  
Check the saved image size and press the  
“MENU/OK” button. The trimmed image is added  
as a separate file in the final frame.  
1Press the “PLAY” button to select Playback  
mode.  
2Unlock the 4-direction button.  
3Press the “MENU/OK” button to display the  
menu screen.  
01  
02  
1
2
3
4
5
6
Image Sizes  
Printing at up to 10R (25.4 × 30.5 cm/10 × 12 in.) /  
A4 size  
6M  
 ?  
03  
Printing at up to 6R (15.2 × 20.3 cm/6 × 8 in.) / A5  
size  
NCEL  
REC  
3M  
Printing at up to 3R (8.9 × 12.7 cm/3.5 × 5 in.) size  
1M  
When you have finished the procedure, lock the 4-  
direction button to prevent accidental improper use.  
1Press “d” or “c” to select “]” TRIMMING.  
2Press the “MENU/OK” button.  
01  
02  
TRIMMING  
SET  
1Press “a” to zoom in. Press “b” to zoom out on  
a still image. A zoom bar appears on the LCD  
monitor.  
2Press the “PLAY” button to move to another part  
of the image.  
01  
01  
02  
4
Zoom bar  
!
Press the “BACK” button to return to single-frame playback.  
PANNING  
CANCEL  
Saved image size varies depending on the zoom  
scale. Up to 1M can be saved.  
SET  
1Press “a”, “b”, “d” or “c” to display another  
area. The current displayed image appears on  
the navigation screen.  
02  
2Press the “MENU/OK” button to save the image.  
Navigation screen  
Press the “PLAY” button to return to zooming.  
ZOOM  
NCEL  
T  
!
98  
99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK MENU  
= LCD BRIGHTNESS  
5
Settings  
SET-UP  
1Press the “PLAY” button to select Playback  
USING THE SET-UP SCREEN  
01  
02  
mode.  
1
2
1Turn the camera on and select Photography  
mode.  
2Press the “MENU/OK” button to display the  
SET-UP screen.  
2Unlock the 4-direction button.  
01 02  
1
2
3
4
SET-UP  
1
2
3
4
5
IMAGE DISP.     :OFF  
1Press the “MENU/OK” button to display the  
menu screen.  
2Press “d” or “c” to select “=” MONITOR  
BRIGHTNESS.  
01  
02  
CUSTOM WB       :SET  
COLOR SPACES    :sRGB  
D-RANGE         :WIDE  
!
Always turn the camera off when replacing the batteries.  
Pulling out the battery holder or disconnecting the AC power  
adapter while the camera is still turned on may return the  
camera settings to the factory default values.  
CANCEL  
SET  
MONITOR  BRIGHTNESS  
SET  
Press “d” or “c” to move to options 1 to 5.  
SET-UP  
1
2
3
4
5
AUTO ROTATE     :ON  
MEDIA           :  
TEST-SHOOTING(N CA):ON  
FORMAT          :OK  
1Pressing the “MENU/OK” button displays the  
monitor brightness setting screen.  
2Press “d ” or “c ” to adjust the monitor  
brightness.  
3Always press the “MENU/OK” button after the  
settings are completed.  
01 03  
02  
3
CANCEL  
T  
1Press “a” or “b” to select a menu option.  
2Press “d” or “c” to change the setting.  
Press “c ” for “CUSTOM WB”, “FORMAT”,  
“DATE/TIME”, “DISCHARGE”, “RESET” or “LIVE  
IMAGE”.  
01  
02  
When you have finished using the menu, lock the  
4-direction button to prevent accidental use.  
CANCEL  
T  
SET-UP  
1
5
2
3
4
5
AUTO ROTATE     :ON  
MEDIA           :  
TEST-SHOOTING(O CAD) ON  
FORMAT          :OK  
Brightness adjustment checking bar  
You can specify whether or not the brightness adjustment checking bar is displayed in the brightness  
setting screen.  
CANCEL  
SET  
100-0009  
After you have changed the settings, press the  
“MENU/OK” button to confirm the changes.  
CANCEL  
ET  
When you have finished using the menu, lock the  
4-direction button to prevent accidental use.  
100  
101  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to display the SET-UP menu (P.101)  
SET-UP  
SET-UP menu options  
IMAGE DISPLAY  
Settings  
Display  
Factory default  
Explanation  
page  
This setting allows you to specify whether the resulting image is displayed after you take a shot.  
Specifies whether the preview images (the photographed  
image) is displayed after taking a picture.  
IMAGE DISP. OFF/ON/PREVIEW  
OFF  
103  
104  
105  
105  
106  
OFF:  
ON:  
The photographed image is automatically recorded without being displayed.  
The photographed image is displayed for about 2 seconds and is then automatically  
recorded.  
Use this setting to specify an the correct white balance  
setting for a light source.  
CUSTOM WB  
SET  
sRGB  
WIDE  
ON  
1
PREVIEW: The photographed image is displayed and then automatically recorded.  
Pressing the “F2” button (Erase) while the image is displayed deletes the recorded  
image. Pressing “F1” (End checking), “MENU/OK”, “BACK” or the shutter button  
clears the display ready for the next shot.  
COLOR  
sRGB/AdobeRGB  
WIDE/STANDARD  
ON/OFF  
Sets the color space to sRGB or Adobe RGB (1998).  
SPACES  
Specifies whether the standard dynamic range (100%) or an  
extended dynamic range (400%) is used.  
D-RANGE  
AUTO  
ROTATE  
Specifies whether the camera automatically detects shots  
taken in the vertical position.  
Procedure when “PREVIEW” is set  
Sets the media to be used when an xD-Picture Card and  
CF/Microdrive are loaded in the camera.  
! (xD-Picture Card)  
~ (CF/Microdrive)  
MEDIA  
!
2
Select “ON” in this setting to release the shutter even when  
no media is loaded in the camera. Note that no image is  
recorded (unless a media is loaded).  
TEST-SHOOTING  
(NO CARD)  
ON/OFF  
ON  
FORMAT  
OK  
LOW/HIGH/OFF  
SET  
LOW  
Erases all files.  
106  
Sets the volume of the tone emitted when the camera  
controls are used.  
% BEEP  
DATE/TIME  
Corrects the date or time.  
27  
!~@: DSC (Mass storage device) mode  
This mode provides a simple way to read images from an a  
media and store images onto a media.  
The USB interface connection can be used for high-speed  
file transfer.  
End checking  
Erase  
Standard chart  
Histograms  
114  
117  
114  
114  
USB MODE  
!~@/$  
!~@  
Preview zoom  
Unlock the 4-direction button and press “a” or “b”  
to zoom in or out.  
To view another part of the image, press the  
“PLAY” button and then press “a”, “b”, “d” or “c”  
to move around. To return to zoom mode, press the  
“PLAY” button again.  
$: PictBridge  
If a printer that supports PictBridge is available, images can  
be printed by connecting the camera directly to the  
PictBridge-compatible printer without using a computer.  
3
!~@: DSC (Mass storage device) mode  
This mode provides a simple way to read images from an a  
media and store images onto a media.  
The IEEE 1394 interface connection can be used for high-  
speed file transfer.  
PANNING  
1394 MODE  
FRAME NO.  
!~@/q1394@  
!~@  
q1394@: 1394 Shooting  
Allows you to control the camera and take pictures from a  
PC. Also allows the photographed images to be  
automatically saved on the PC.  
Histogram  
5
Histogram  
Pressing this button displays the histogram.  
The display changes in a cycle from MASTER R  
G B each time the button is pressed.  
Specifies whether frame numbers are assigned  
consecutively from previous numbers or begin again.  
CONT./RENEW  
CONT.  
106  
28  
MASTER  
MIN  
ENGLISH Specifies the language used for LCD monitor display.  
4
5
MAX  
!
See P.85 for more information on histograms.  
VIDEO SYSTEM  
DISCHARGE  
NTSC/PAL  
OK  
Specifies whether video output is set to NTSC or PAL.  
Discharges Ni-MH batteries.  
107  
Resets all the camera settings (other than the CUSTOM  
WB, FORMAT, DATE/TIME, LANG. and VIDEO SYSTEM,  
LIVE IMAGE) to the factory default values set at shipment.  
A confirmation message appears when you press “c”. To  
reset the camera settings, press the “MENU/OK” button  
again.  
Brightness warning and standard chart  
The display switches between the brightness  
warning indicator and the standard chart each time  
you press the button.  
Use these features to check the brightness and  
color tones in the image.  
Brightness warning  
RESET  
OK  
ON  
Gray scale  
Color bar  
LIVE IMAGE  
Displays the live image on the LCD monitor.  
108  
102  
103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to display the SET-UP menu (P.101)  
SET-UP  
If the exposure is measured correctly,  
7” appears on the LCD monitor.  
Press the “MENU/OK” button to confirm the setting.  
SETTING THE CUSTOM WB  
5
Use this function to set the correct white balance for a light source. You can also use this  
function to achieve a desired special effect.  
1
Press the “F1” (custom WB 1) button or the “F4” (custom WB 2) button to select the custom  
white balance you want to set.  
COMPLEED !  
CANCEL  
T  
!
After taking the picture, check the color tones (white balance)  
in the image.  
i Select “PREVIEW” as the photographed image display  
option (P.103) in the SET-UP screen.  
i Press the “PLAY” button (P.43).  
When you have finished setting the white balance, select the  
focus mode you want to use.  
WB  
CUS.2  
When the exposure is not measured correctly  
Remedy  
Custom WB 1  
Custom WB 2  
The subject is too bright. Use a negative (–) exposure compensation value and set the  
white balance again.  
Turn the focus mode selector switch to “M” (Manual  
focus) and set the focus manually.  
The subject is too dark. Use a positive (+) exposure compensation value and set the white  
balance again.  
2
3
4
Because the exposure is outside the range of valid custom white balance settings, the  
maximum (or minimum) value has been set.  
h Available custom WB settings: Color temperatures of approx. 2800 K to 9500 K  
!
The camera’s auto focus function may be unable to focus on  
a subject such as a white sheet of paper, which will prevent  
the shutter from operating.  
COLOR SPACES  
Selects the color space used when pictures are  
taken. For normal photography, select sRGB.  
Adobe RGB (1998) is best for images to be used  
for commercial printing.  
SET-UP  
Set the exposure mode to “P”, “S” or “A”.  
1
2
3
4
5
IMAGE DISP.      :OFF  
CUSTOM WB        :SET  
COLOR SPACES      sRGB  
D-RANGE          :WIDE  
!
While a custom white balance can also be measured in “M”  
mode, the image may be extremely overexposed or  
underexposed so that the optimum measurement is not  
taken.  
CANCEL  
SET  
5
D-RANGE  
Hold up a page of white paper or a similar object  
under the target light source so that the paper  
fills the viewfinder screen. Then press the shutter  
button to set the custom white balance.  
WIDE: Allows photography using a wide dynamic  
range that takes advantage of the particular  
characteristics of the Super CCD SR II. The  
continuous shooting speed and interval are  
slower than for standard mode (roughly  
double), so the number of continuous shots  
available roughly half.  
SET-UP  
1
2
3
4
5
IMAGE DISP.      :OFF  
CUSTOM WB        :SET  
COLOR SPACES     :sRGB  
D-RANGE           WIDE  
h Range of custom WB settings  
Color temperatures from approx. 2800 K to  
9500 K  
CANCEL  
SET  
STANDARD: The dynamic range is 100%, as on  
the previous digital camera (FinePix  
S2 Pro), but the continuous shooting  
speed and the number of continuous  
shots available are increased for  
easier shooting.  
Matching customized white balance using an external flash  
If you use an external flash with the exposure mode set to “M”, you can make it easier to match the  
white balance to the photography settings (aperture, flash brightness, etc.) by using a commercially  
available 18% grey standard chart instead of white paper.  
104  
105  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to display the SET-UP menu (P.101)  
SET-UP  
Check the file number by viewing the image. The  
last 4 digits of the 7-digit number are the file  
numbers, while the first 3 digits show the directory  
number.  
AUTO ROTATE  
Frame number  
Detects whether the camera is used horizontally or  
vertically so that images are automatically rotated  
when opened in the optional dedicated software,  
Hyper-Utility Software HS-V2 Ver. 3.0.  
SET-UP  
1
2
3
4
5
Directory number  
File number  
AUTO ROTATE       N  
MEDIA            :  
TEST-SHOTINNO CARD):ON  
FORMA            :OK  
!
When changing the media, always turn the camera off before  
opening the slot cover. Opening the slot cover without turning  
the camera off may cause the frame number memory to not  
function.  
!
The camera may record the horizontal/vertical position  
information incorrectly during panning or when pictures are  
taken facing upwards or downwards. In such situations,  
select “OFF”.  
100-0009  
!
File number runs from 0001 to 9999. Once 9999 is exceeded,  
the directory number changes from 100 to 101. The  
maximum number is 999–9999.  
CANCEL  
SET  
!
Rotated display does not apply to playback images.  
!
The displayed frame number may differ for images  
photographed on other cameras.  
!
When “q” appears, see P.134.  
FORMAT  
Initialize (format) the media for use with the  
camera.  
Because initializing the media erases all the frames  
(files), including protected frames (files). Back up  
important frames (files) onto your computer or  
another media.  
1Press “d” or “c” to select “OK”.  
2Pressing the “MENU/OK” button erases all the  
frames (files) and initializes the media.  
FORMAT  
DISCHARGING RECHARGEABLE BATTERIES  
The “Discharging rechargeable batteries” function can only be used with Ni-MH  
batteries.  
Use the “Discharging rechargeable batteries” function in the following situations:  
i When the batteries only last for a short time after being charged normally  
i When the batteries have not been used for a long period  
i When you purchase new Ni-MH batteries  
Do not use the “Discharging rechargeable batteries” function while using the AC power adapter. In  
these situations, the Ni-MH batteries will not be discharged due to the external power supply.  
    FMA ?  
 LL A  
OK  
CANCEL  
T  
01  
02  
!
Always check the media to be formatted on the screen before  
proceeding.  
h Formatted media  
8: xD-Picture Cards  
9: CF/Microdrives  
If “i”, “0”, “-” or  
=” appears, see P.134 for information  
before formatting the media.  
1Press “d” or “c” to move to option 4 and then  
press “a” or “b” to select “DISCHARGE”.  
2Press “c”.  
SET-UP  
!
1
1
2
3
4
5
FRAME NO.        :CONT.  
言語  
/LANG.       :ENLISH  
VIDEO SYSTEM    :NTSC  
DISCHARGE        OK  
FRAME NO.  
Specifies whether frame numbers are assigned  
consecutively from previous numbers or begin  
again.  
CONT. : Pictures are stored beginning from the  
highest file number stored on the last  
media used.  
RENEW: Pictures are stored on each media  
beginning with a file number “0001”.  
Setting this function to “CONT.” makes file  
management easier as it ensures that file names  
are not duplicated when images are downloaded to  
a PC.  
CANCEL  
SET  
CONT.  
RENEW  
01  
01  
02  
A
B
5
1Press “d” or “c” to select “OK”.  
2Press the “MENU/OK” button.  
02  
2
Formatted media used for both A and B.  
The screen changes and discharging begins.  
When the battery level indicator blinks red and  
discharging ends, the camera turns off.  
!
When the camera settings are “RESET”, the frame number  
setting (“CONT.” or “RENEW”) is changed to “CONT.” and  
the frame number itself does not return to “0001”.  
When the media already contains image files with file  
numbers higher than the highest file number on the last  
media, images are stored beginning from the highest file  
number on the current media.  
DISCHARGE  
DISCHARE OK?  
!
IT MAY TAKE A WHILE  
FOR DISCARGING  
OK  
CANCEL  
SET  
!
To cancel discharging, press the “BACK” button.  
106  
107  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to display the SET-UP menu (P.101)  
SET-UP  
TWO-BUTTON RESET  
Two-Button Reset lets you instantly reset specified settings to their original initial settings.  
LIVE IMAGE  
To manually focus the image more sharply or to  
check the image, you can view the image in black  
and white on the LCD monitor while adjusting the  
focus. The live image is only displayed for 30  
seconds. Adjust the focus manually during this  
period. Live images are displayed using the actual  
aperture setting.  
Set the exposure mode dial to “P”, “S”, “A”, “M” or  
CSM” and select the settings to be reset.  
SET-UP  
1
1
2
3
4
5
          K  
       N  
CANCEL  
SET  
!
Use this feature in “M” (Manual focus) mode.  
Exposure mode dial  
“P”, “S”, “A”, “M”  
Reset Settings  
Set the focus mode selector switch to “M”.  
The photography functions are reset as shown below.  
1
2
Function  
Focus area  
Condition  
Center  
Flexible Program  
Cancelled  
Exposure compensation  
Auto Exposure Bracketing  
Auto Exposure Lock  
Cancelled  
Cancelled  
Cancelled  
Flash Synchro mode  
Flash exposure compensation  
Front Synchro mode  
Cancelled  
In the SET-UP screen, select “LIVE IMAGE” and  
then press “c”. In the confirmation screen, press  
the “MENU/OK” button.  
SET-UP  
1
2
3
4
5
h All the custom settings are reset.  
h The ISO sensitivity is reset to 200.  
“CSM”  
          K  
       N  
Hold down the “c” and “b” buttons together for  
at least 2 seconds (green markings are positioned  
alongside).  
The top display panel flashes briefly and the  
settings are reset.  
CANCEL  
SET  
2
3
!
The flash fires when the internal flash pops up or when an  
external flash is connected and the live image is displayed.  
The live image is displayed for 30 seconds. Use  
d” or “c” to adjust the brightness. In the live  
image display, press “a” to enlarge the central part  
of the image and “b” to return to the original image.  
To cancel live image display in progress, press the  
“BACK” button.  
When the reset is finished, set the exposure mode dial to a setting other than “CSM”.  
5
3
SEC  
!
To view the live image, use the optional AC adapter AC-5VX.  
Continued use of live image display can cause the CCD to  
overheat, resulting in coarseness or noise such as white  
spotting in images photographed subsequently. If this occurs,  
turn the camera off and wait for it to cool down.  
CANCEL  
GE  
!
If you display consecutive live images, the initial brightness  
setting is retained for the second and subsequent images.  
The setting is reset when you turn the camera off (or the Auto  
Power Off function is triggered) and has to be set again.  
The Auto Exposure Bracketing settings are canceled when  
the live image is displayed. Wait until live image display is  
finished before specifying the Auto Exposure Bracketing  
settings.  
!
108  
109  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(
)
CUSTOM SETTING CSM  
The custom settings allow to modify camera functions such as how information is displayed in the  
viewfinder and which functions are assigned to which buttons.  
Custom settings list  
No.  
Setting  
Display  
Details  
0: METERED VALUE  
UNDER OVER  
(default)  
1: UNDER ➡  
METERED VALUE  
OVER  
1
BRACKETING ORDER  
Allows you to change the compensation sequence  
when auto exposure bracketing is used.  
Set the Exposure mode dial to “CSM”.  
1
2
ON-DEMAND GRID  
LINES DISPLAY  
0: OFF (default)  
1: ON  
If you display the On-Demand Grid Lines, you can use  
the intersections of the horizontal and vertical lines to  
position your main subject in the shot or align one of the  
horizontal lines with the horizon. This allows you to  
compose the desired shot while monitoring the subject's  
size and the balance.  
1Turn the Main-command dial to select an option.  
 SEG  
2
2Turn the Sub-command dial to change the  
setting.  
3E” appears on the top display panel.  
 1 BRACKETING ORDER  
3
4
ILLUMINATION FOR  
FOCUS AREA  
0: AUTO (default)  
1: OFF  
2: ON  
Specifies the illumination used for the focus area in the  
viewfinder.  
METERED VALUE→UNDER→OVER  
UNDER→METERED VALUE→OVER  
FOCUS AREA  
SELECTION  
0: NORMAL (default)  
1: ENABLES  
ROTATION  
Selecting cyclic focus area selection allows you to  
select the opposite focus area without changing which  
part of the 4-direction button you have to press.  
MAIN  
NU  
SUB  
SETTING  
5
6
7
AE-LOCK  
0: DISABLED (default) Set this parameter to “1” to apply the AE lock when the  
1: ACTIVATED shutter button is pressed half way.  
01  
03  
02  
LONG EXP. (BULB) AT  
MANUAL MODE  
0: DISABLED (default) Select “1” to take bulb shots in the “M” exposure mode.  
1: ACTIVATED  
CLOSEST-SUBJECT-  
PRIORITY DYNAMIC AF 1: DISABLED  
AT AF-S MODE  
0: ENABLED (default) If you select “1”, Closest-subject Priority Dynamic AF is  
not used in AF-S mode.  
8
9
CLOSEST-SUBJECT-  
PRIORITY DYNAMIC AF 1: ENABLED  
AT AF-C MODE  
0: DISABLED (default) If you select “1”, Closest-subject Priority Dynamic AF is  
used in AF-C mode.  
AE/AF LOCK BUTTON  
0: AE/AF LOCK  
(default)  
1: AE LOCK ONLY  
2: AF LOCK ONLY  
3: AE REMAINS  
LOCKED  
Normally, AE lock (exposure recording) and AF lock  
(focus lock) are both applied concurrently when you  
press the “AE-L/AF-L” button. However, this can be  
changed so that only AE lock or only AF lock is applied,  
or so that that the AE lock status is maintained. If the  
AE/AF lock is used with the “Maintain AE lock” setting,  
pressing the “AE-L/AF-L” button again or releasing the  
shutter cancels the lock.  
When you have finished the settings, set the exposure mode dial to a setting other than “CSM”.  
3 !  
The custom settings are retained when the camera is turned off.  
5
4: AF OPERATION  
Cancelling custom settings  
In addition, though the auto focus (AF) normally  
operates when the shutter button is pressed down  
halfway, you can change this so that AF operates when  
the “AE-L/AF-L” button is pressed. (In this case, AF  
does not operate when the shutter button is pressed  
down halfway.)  
1Set the Exposure mode dial to “CSM”.  
2Hold down the “c” and “b” buttons together  
for at least 2 seconds (green markings are  
positioned alongside).  
The top display panel flashes briefly and the  
settings are reset.  
01  
10 COMMAND DIAL  
FUNCTIONS  
0: DISABLED (default) Use this setting to change the Main-command dial and  
1: ENABLED  
Sub-command dial operation during photography.  
0: Main: Changes the shutter speed.  
Sub: Changes the aperture.  
1: Main: Changes the aperture.  
Sub: Changes the shutter speed.  
h All the custom settings are reset to their default  
values.  
h The ISO sensitivity is reset to 200.  
02  
02  
11 MULTIPLE EXPOSURE 0: SINGLE SHUTTER Changing this setting allows you to use continuous  
RELEASE (default) shooting for multiple exposure shots.  
1: CONTINUOUS  
SHUTTER  
RELEASE  
110  
111  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO A TV /  
(
)
CUSTOM SETTING CSM  
6
Connection  
USING THE AC POWER ADAPTER  
No.  
Setting  
Display  
Details  
Connecting to a TV  
12 AUTO POWER OFF  
0: OFF  
15: 15 SEC. (default)  
2: 2 MIN.  
Sets the delay time until the Auto Power Off function  
operates.  
Turn off the camera and TV. Open the terminal  
cover and plug the bundled video cable into the  
camera’s “VIDEO OUT” (video output) socket.  
1
5: 5 MIN.  
VIDEO OUT  
socket  
13 SELF-TIMER  
DURATION  
2: 2 SEC.  
5: 5 SEC.  
Sets the running time for the self-timer.  
10: 10 SEC. (default)  
20: 20 SEC.  
14 LCD ILLUMINATION  
0: OFF (default)  
5: 5 SEC.  
Allows you to change the settings so that the LCD  
illumination lights when buttons are used.  
15: 15 SEC.  
15 AF-ASSIST  
ILLUMINATOR  
0: ON (default)  
1: OFF  
Allows you to prevent the built-in AF-assist illuminator  
from operating. Note that this may prevent the auto  
focus from successfully setting the focus in some cases.  
!
If there is a power outlet available, connect the AC Power  
Adapter AC-5VX.  
Plug the other end of the cable into the video input  
socket on the TV. Then turn the camera and TV on  
and take pictures or play back images as you  
would normally.  
2
To video  
input socket  
!
Refer to the instructions provided with your TV for more  
information on video input for your TV.  
(
)
Using the AC Power adapter sold separately  
The AC Power Adapter is useful since it allows you to take pictures, play back images (connected  
to a TV, etc.) and connect to a computer without worrying about using up the battery charge.  
h Compatible AC power adapter  
Model: AC-5VX  
Check that the camera is turned off. Open the  
01  
02  
terminal cover and plug the AC power adapter  
connector into the “DC IN 5V” socket. Then plug  
the AC power adapter into a power outlet.  
!
Use only the FUJIFILM products listed above.  
See P.130 for notes on using the AC power adapter.  
The socket-outlet shall be installed near the equipment and  
shall be easily accessible.  
6
!
!
DC IN 5V socket  
!
The shape of the plug and socket-outlet depends on the  
country of use.  
112  
113  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO A COMPUTER  
The “Connecting to a computer” section explains how to connect the camera to your computer  
using the USB cable (IEEE 1394 cable) and describes the functions you can use once the camera  
and computer are connected.  
USE ATDSCMODE
Set a camera  
1
If the power cuts out during data transmission, the data will not be transmitted correctly. Always use the  
AC power adapter when connecting the camera to a computer.  
1Insert a media with images into the camera.  
2Turn the camera on and press the “MENU/OK”  
button.  
3Select “!~@” in “USB MODE” or “1394  
MODE” in the SET-UP menu (P.101) and then  
turn the camera off.  
01  
02  
Refer to Software Quick Start Guide the first time you connect the  
camera to your computer.  
Install the software first. Do not connect the camera with  
the computer before installing all the software.  
SET-UP  
1
03  
CD-ROM  
(Software for FinePix)  
2
3
4
5
BEEP          :LOW  
!
Use the AC Power Adapter AC-5VX (sold separately) for the  
connection (P.113). If shutting off power supply during  
communication, the files on the media may be damaged.  
If inserting an xD-Picture Card and a CF/Microdrive into the  
camera at the same time, images will be recorded onto the  
media selected as the “MEDIA” (P.102).  
h If your PC supports USB 2.0 (High-speed USB), data can be transferred faster than with previous  
USB versions.  
DATE/TIME       :SET  
USB MODE          
1394 MODE       :  
!
!
This camera does not support IEEE 1394b (FireWire 800). Use IEEE 1394 (FireWire 400).  
CANCEL  
T  
(
)
DSC Mass storage device mode  
!~@  
Connect a camera to a computer  
This mode provides a simple way to read images from a media and store images onto a media. The  
USB or IEEE 1394 (FireWire) interface connection can be used for high-speed file transfer (P.115).  
To connect via an IEEE 1394 port, check that the interface is OHCI compliant and then refer to the  
table below to check whether it is supported by your operating system.  
2
1Turn your PC on.  
Camera  
2Connect the camera to the PC using the USB  
cable (mini-B) or IEEE 1394 cable.  
3Turn the camera on.  
USB  
Operating system compatibility chart (Windows)  
: Can be connected  
: Cannot be connected  
socket  
(mini-B)  
OS  
Windows 98 SE  
(Second Edition) (Millennium Edition)  
Windows Me  
Windows 2000  
(Professional)  
Windows 98  
Windows XP  
Connection type  
USB  
PC  
DC IN 5V socket  
Camera  
socket  
2  
IEEE 1394  
USB  
1  
IEEE  
1394 socket  
1 Can be used by installing the driver from the bundled CD-ROM.  
2 Select Windows Update from the Start button menu and update the 1394 device driver (Your system must be  
!
Always use the cable provided with your camera. If you use  
other cable, your camera may not work correctly.  
Make sure that the USB cable (mini-B) or IEEE 1394 cable is  
connected correctly and is pushed in.  
capable of connecting to the Internet).  
IEEE  
1394 socket  
!
Operating system compatibility chart (Macintosh)  
: Can be connected  
Mac OS X2  
PC  
!
Do not connect the USB cable (mini-B) and the IEEE 1394  
cable at the same time.  
OS  
Mac OS 9.2.21  
DC IN 5V socket  
Connection type  
IEEE 1394  
h The access lamp blinks when the camera and  
computer are exchanging data.  
USB  
6
h w ” is displayed on rear display  
panel.  
h Power save and Auto power off are disabled  
during DSC connection.  
2 Versions 10.2.6 to 10.3.5 as at November 2004. Refer to the FUJIFILM website for information on supported  
operating systems.  
DSC  
!
Before replacing the media, always disconnect the camera  
from the PC using the procedure on P.116.  
Do not disconnect the USB cable (mini-B) or IEEE 1394  
cable while communication is in progress. If shutting off  
power supply during communication, the files on the media  
may be damaged.  
IEEE 1394 photography function  
For information on taking pictures using IEEE 1394, refer to the Hyper Utility Software HS-V2  
Ver.3.0 (or later) Quick Start Guide.  
!
114  
115  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING THE CAMERA DIRECTLY TO THE PRINTER  
PictBridge FUNCTION  
CONNECTING TO A COMPUTER  
When a printer that supports PictBridge is available, images can be printed by connecting the  
camera directly to the PictBridge-compatible printer without using a PC.  
Disconnecting the camera  
Quit all applications (FinePixViewer etc.) that are using the camera.  
!
In PictBridge function, images photographed on other than a camera may not be printed.  
Always turn the camera off when disconnecting or connecting the USB cable. Connecting the camera to the printer while  
the camera is turned on could damage the media.  
1
2
!
Perform the steps shown below before you turn the camera off. This procedure differs  
depending on the operating system software (or PC) you are using.  
Specifying images for printing on the camera  
1Set the Power switch to “ON”.  
2Select “$” in “USB MODE” in the “SET-UP”  
menu (P.101).  
3Set the Power switch to “OFF” to turn the  
camera off.  
Check that the access lamp is off (no data is being  
exchanged with the computer).  
01  
30  
1
2
OFF  
!
In some cases, the camera and computer may still be  
communicating even after the “Copying” message disappears  
from the computer screen. Always check that the access  
lamp is off.  
SET-UP  
1
02  
2
3
4
5
BEEP          :LOW  
Windows 98/98 SE (USB)  
No PC operation is needed.  
DATE/TIME        :SET  
USB MODE          
1394 MODE       :  
!
Do not connect to a PC when the USB mode setting is set to  
$”. See P.137 if you connect to a PC by mistake.  
Windows 98 SE (IEEE 1394) /Me/2000 Professional/XP  
1Right-click the removable disk icon in the “My Computer”  
window and select Eject. This step is only required in  
Windows Me.  
CANCEL  
T  
1Connect the camera to the printer using the USB  
cable (mini-B).  
2Turn the printer on.  
USB  
socket  
(mini-B)  
!
The camera cannot be used to specify printer settings such  
as the paper size and print quality.  
Please connect the AC Power Adapter AC-5VX (sold  
separately) to your camera.  
2Left-click the Eject icon in the taskbar and select “USB Disk”.  
!
Screen for Windows XP  
DC IN 5V socket  
!
Use a media that was formatted on the camera.  
3The menu option shown below appears. Click on this option.  
Set the Power switch to “ON”.  
3
4
Screen for Windows XP  
4The “Safe To Remove Hardware” message box appears. Click the [OK] button or the close  
button.  
Macintosh  
Drag the “Removable drive” icon on the desktop to the  
Trash.  
6
$ CHECKING USB” appears on the rear  
display panel for a few moments and then the  
menu screen appears on the LCD monitor.  
!
When you drag the icon to the Trash, “REMOVE OK” appears on  
the camera’s screen.  
CHECKG USB  
1Turn the camera off.  
2Unplug the USB cable (mini-B) or IEEE 1394  
01  
02  
3
cable from the camera.  
USB  
socket  
(mini-B)  
!
If the menu does not appear, check whether the USB mode  
setting is $”.  
DC IN 5V  
socket  
!
Depending on the printer, some functions are disabled.  
Continued  
116  
117  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING THE CAMERA DIRECTLY TO THE PRINTER —  
PictBridge FUNCTION  
1Press “a” or “b” to select “u PRINT DPOF”.  
2Press the “MENU/OK” button.  
1Connect the camera to the printer using the USB  
cable (mini-B).  
2Turn the printer on.  
01  
02  
5
2
USB  
socket  
(mini-B)  
!
The camera cannot be used to specify printer settings such  
as the paper size and print quality.  
PICTBIDGE  
!
Please connect the AC Power Adapter AC-5VX (sold  
separately) to your camera.  
Use a media that was formatted on the camera.  
!
When “t” appears, the DPOF settings are not  
specified.  
PRINT WITH DATE  
PRINT WITHOUT DATE  
PRINT DPOF  
DC IN 5V socket  
!
!
To use DPOF printing, the DPOF settings must be specified  
on FinePix S3 Pro beforehand (P.94).  
Even when “WITH DATE” is specified in the DPOF settings,  
the date is not inserted on printers that do not support date  
printing.  
!
Set the Power switch to “ON”.  
SET  
3
4
Press the “MENU/OK” button to download the data  
to the printer and print the frames specified in the  
DPOF settings.  
6
PRINT  DPOF  
TOTAL/    19SEETS  
Press the “BACK” button to return to step 5.  
PRINT DPOF OK?  
CANCEL   
$ CHECKING USB” appears on the rear  
display panel for a few moments and then the  
menu screen appears on the LCD monitor.  
YES  
CHECKG USB  
PRINT  DPOF  
PRINTING  
!
If the menu does not appear, check whether the USB mode  
setting is $”.  
!
Depending on the printer, some functions are disabled.  
!
Press the “BACK” button to cancel the printing. Depending on  
the printer, the printing may not be canceled immediately or  
printing may stop midway through. When printing stops  
midway, briefly turn the camera off and then on again.  
    1/    19SHEES  
CACEL  
1Press “a” or “b” to select “PRINT WITH DATE”  
or “PRINT WITHOUT DATE”. If “PRINT WITH  
DATE” is selected, the date is imprinted on your  
prints.  
01  
02  
5
(
)
Specifying images for printing without using DPOF single-frame printing  
2Press the “MENU/OK” button.  
1Set the Power switch to “ON”.  
2Select “$” in “USB MODE” in the “SET-UP”  
menu (P.101).  
3Set the Power switch to “OFF” to turn the  
camera off.  
01  
30  
PICTBRIDGE  
1
6
PRINT WIT DATE  
PRINT WITHUT DATE  
PRINT DPOF  
!
“PRINT WITH DATE” is not available when the camera is  
connected to a printer that does not support date printing.  
SET  
SET-UP  
1
02  
2
3
4
5
BEEP          :LOW  
DATE/IME          :SET  
USB MODE           
1394 MODE        :  
!
Do not connect to a PC when the USB mode setting is set to  
$”. See P.137 if you connect to PC by mistake.  
CANCEL  
T  
Continued  
118  
119  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING THE CAMERA DIRECTLY TO THE PRINTER —  
PictBridge FUNCTION  
System Expansion Options  
1Press “d” or “c” to display the frame (file) for  
which you want to specify PRINT settings.  
2Press “a” or “b” to set a value up to 99 as the  
number of copies of the frame (file) to be printed.  
For frames (files) that you do not want printed,  
set the number of prints to 0 (zero).  
To specify more PRINT settings, repeat steps 1  
and 2.  
3Press the “MENU/OK” button.  
eBy using the FinePix S3 Pro together with other optional FUJIFILM products, your system can be  
expanded to fill a wide range of uses.  
01 02  
30  
6
7
8
Image input/output to the PC  
1000001  
USB / IEEE 1394  
TOTAL00001  
01 SHEETS  
Personal Computer  
(commercially available)  
FinePix S3 Pro  
Digital Camera  
FRAME  
PC Card Adapter  
(PC card slot)  
CANCEL  
YES  
CF / Microdrive  
Always press the “MENU/OK” button after the  
settings are completed.  
(commercially available)  
Image Memory Card Reader  
DPC-R1  
TOTAL/    19SEETS  
(
)
USB  
xD-Picture CardUSB Drive  
DPC-UD1  
PRINT OK?  
CANCEL  
YES  
(
)
USB  
PC Card Adapter DPC-AD  
(PC card slot)  
xD-Picture Card  
!
Press the “BACK” button to return to step  
.
5
D
P
C
-C  
F
CompactFlash™ Card Adapter  
DPC-CF  
CO  
MP  
ACTFLASH  
C
A
R
D
A
D
Press the “MENU/OK” button to download the data  
to the printer and start printing the specified  
number of prints.  
A
P
TM  
T
E
R
fo  
r
xD  
-P  
ic  
tu  
re  
ar  
d
(CF card slot)  
PRINTING  
Print creation  
  1/    SHEETS  
CANCEL  
USB  
Printer  
(commercially available)  
Personal Computer  
!
Press the “BACK” button to cancel the printing. Depending on  
the printer, the printing may not be canceled immediately or  
printing may stop midway through. When printing stops  
midway, briefly turn the camera off and then on again.  
FinePix S3 Pro  
Digital Camera  
(commercially available)  
PictBridge  
Disconnecting the printer  
Digital Photo  
Printer CX-550  
1Check that “y” is not displayed on the  
camera’s screen.  
xD-Picture Card  
2Turn the camera off. Unplug the USB cable  
(mini-B).  
Visual output  
USB  
socket  
(mini-B)  
Visual output  
DC IN 5V socket  
FinePix S3 Pro  
Digital Camera  
TV monitor  
(commercially available)  
120  
121  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories Guide  
eAccessories (sold separately) can make taking pictures with the FinePix S3 Pro even easier. For  
information on how to attach and use accessories, refer to the instructions provided with the  
accessory used.  
Visit the FUJIFILM web site for the latest information on camera accessories.  
h Hyper-Utility Software HS-V2 Ver.3.0  
h Offers PC-based functions such as browsing, two-image comparison, image sorting and organizing using a  
marker function, and image analysis using histogram and highlight warning displays for images shot on a  
digital camera.  
h Allows you to specify the output image size and the processing parameters (tone curve, white balance,  
sharpness, color and dynamic range) for CCD-RAW files and also allows you to convert them to ordinary  
image files (16-bit/8-bit TIFF or Exif JPEG).  
h Allows images shot on a FinePix S3 Pro to be downloaded directly to a PC without using a recording media  
by connecting the camera to the PC’s IEEE 1394 interface (Photography function).  
h Provides a range of other functions for using photographed images in various ways, including printing,  
contact-sheet file creation and slide shows.  
h xD-Picture Card  
These are separately available xD-Picture Cards.  
Use the following xD-Picture Card:  
DPC-16 (16 MB)/DPC-32 (32 MB)/DPC-64 (64 MB)/DPC-128 (128 MB)/  
DPC-256 (256 MB)/DPC-512 (512 MB)  
h Refer to the product package for detailed information on specifications and system requirements.  
h AC Power Adapter AC-5VX  
Use the AC-5VX when taking pictures or play back images for long periods or when  
the FinePix S3 Pro is connected to a personal computer.  
The shape of the AC power adapter, the plug and socket outlet depend on the  
country.  
h Fujifilm Rechargeable Battery 2HR-3UF  
The 2HR-3UF includes 2 pieces of high-capacity AA-size Nickel-Metal Hydride (Ni-  
MH) batteries.  
h Fujifilm Battery Charger with Battery BK-NH2  
(With Euro type or UK type plug)  
The BK-NH2 includes the quick battery charger BCH-NH2 and 2 Ni-MH batteries.  
The BCH-NH2 can charge 2 Ni-MH batteries in approximately 120 minutes.  
Up to 4 Ni-MH batteries can be charged simultaneously.  
h Image Memory Card Reader DPC-R1  
The DPC-R1 provides a quick and easy way to transfer images back and forth  
between your PC and an image memory card (xD-Picture Card and SmartMedia).  
The DPC-R1 uses the USB interface for high-speed file transfer.  
h Compatible with Windows 98/98 SE, Windows Me, Windows 2000 Professional,  
Windows XP or iMac, Mac OS 8.6 to 9.2.2, Mac OS X (10.1.2 to 10.2.2) and  
models that support USB as standard.  
h Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 4  
MB to 128 MB.  
h PC Card Adapter DPC-AD  
The PC Card Adapter allows the xD-Picture Card and SmartMedia to be used as a  
PC Card Standard ATA-compliant (PCMCIA 2.1) PC card (Type II).  
h Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 2  
MB to 128 MB.  
h CompactFlash™ Card Adapter DPC-CF  
D
P
C
-
C
F
Loading an xD-Picture Card into this adapter allows you to use the card as a  
CompactFlash card (Type I).  
C
O
M
R
P
A
C
A
A
C
T
F
P
D
L
A
E
D
A
S
H
TM  
T
R
fo  
r
xD  
-P  
ic  
tu  
r
ar  
d
h Windows 95/98/98 SE/Me/2000 Professional/XP  
h Mac OS 8.6 to 9.2/X (10.1.2 to 10.1.5)  
h xD-Picture Card™ USB Drive DPC-UD1  
This is a compact card reader for xD-Picture Cards. Simply plug the drive into the  
USB port to read and write data to an xD-Picture Card. (No driver installation is  
required except on Windows 98/98 SE.)  
h Compatible with xD-Picture Card of 16 MB to 512 MB  
h Windows 98/98 SE/Me/2000 Professional/XP  
h Mac OS 9.0 to 9.2/X (10.0.4 to 10.2.6)  
122  
123  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes on Using Your Camera Correctly  
Cleaning the CCD  
This camera is equipped with a CCD photosensitive element. This CCD is located behind the  
shutter screen.  
eBe sure to read this information in conjunction with “Safety Notes” (P.141), to ensure that you  
use your camera correctly.  
If dust or other soiling attaches to the surface of the CCD and pictures are then taken, this soiling  
may appear as spots in the image, depending on the camera settings and the type of subject. If this  
occurs, the CCD must be cleaned. Because the surface of the CCD is extremely fragile, wherever  
possible the camera should be returned to an authorized FUJIFILM dealer for cleaning (for a  
charge).  
Any repairs carried out by an authorized FUJIFILM dealer to CCDs that were scratched or damaged  
during cleaning by the customer will be charged to the customer. Note that such repairs will  
probably involve replacing the CCD and will be expensive.  
Places to Avoid  
Do not store or use the camera in the following types of locations:  
h In the rain or in very humid, dirty or dusty places.  
h In direct sunlight or in places subject to extreme temperature rises, such as in a closed car in summer.  
h Extremely cold places.  
h Places subject to strong vibration.  
h Places affected by smoke or steam.  
h Places subject to strong magnetic fields (such as near motors, transformers or magnets).  
h In contact with chemicals such as pesticides or next to rubber or vinyl products for long periods of time.  
Dust inside the camera and on the surface of the CCD  
Notes on Immersion in Water or Sand  
h Before a FUJIFILM digital camera is shipped from the factory, it is carefully checked for dust inside  
the camera and on the surface of the CCD to ensure that it conforms to FUJIFILM standards.  
h Bear in mind also that some types of soiling on the CCD surface cannot be removed even by an  
authorized FUJIFILM dealer.  
Should this occur, you can use features such as the despeckling function provided in the image  
processing software to remedy the problem.  
The FinePix S3 Pro is particularly adversely affected by water and sand. When you are at the beach or close to  
water, ensure that the camera is not exposed to water or sand. Take care also not to place the camera on a  
wet surface. Water or sand inside the camera can cause faults that may be irreparable.  
Notes on Condensation  
If the camera is carried suddenly from a cold location into a warm place, water droplets (condensation) may  
form on the inside of the camera or on the lens. When this occurs, switch the camera off and wait an hour  
before using the camera. Condensation may also form on the media. In this event, remove the media and  
wait a short time before using it again.  
Checking the condition of the CCD surface  
When the Camera is Unused for Long Periods  
Check that the camera is turned off.  
If you do not intend to use the camera for a long period of time, remove the battery and the media card  
before storing the camera.  
Open the terminal cover and fully insert the  
1
connector plug from the AC power adapter AC-5VX  
(sold separately) into the “DC IN 5V” socket. Then  
plug the AC power adapter into the power outlet.  
Cleaning Your Camera  
h Use a blower brush to brush away any dust on the lens, LCD monitor surface, viewfinder or external AF  
sensor and then gently wipe the camera with a soft, dry cloth. If any soiling remains, apply a small  
amount of lens cleaning liquid to a piece of FUJIFILM lens cleaning paper and wipe gently.  
h Do not scratch hard objects against the lens, LCD monitor screen or viewfinder as these surfaces are  
easily damaged.  
h Clean the body of the camera with a soft, dry cloth. Do not use volatile substances such as thinners,  
benzine or insecticide, as these may react with camera body and cause deformation or remove the  
coating.  
!
When cleaning the camera, always use the AC power  
adapter AC-5VX (sold separately) to prevent camera damage  
due the mirror dropping down or the shutter closing.  
See P.130 for more information on using the AC power  
adapter.  
DC IN 5V socket  
!
Press the built-in flash down to stow it away.  
h This camera is equipped with a CCD photosensitive element. This CCD is located behind the shutter  
screen. If dust or other soiling attaches to the surface of the CCD and pictures are then taken, this soiling  
may appear as spots in the image, depending on the camera settings and the type of subject. If this  
occurs, the CCD must be cleaned. Because the surface of the CCD is extremely fragile, wherever  
possible the camera should be returned to an authorized FUJIFILM dealer for cleaning (for a charge).  
Any repairs carried out by an authorized FUJIFILM service facility to CCDs that were scratched or  
damaged during cleaning by the customer will be charged to the customer. Note that such repairs will  
probably involve replacing the CCD and will be expensive.  
2
3
Take the following precautions to ensure that no dirt or dust gets onto the CCD:  
i Before a FUJIFILM digital camera is shipped from the factory, it is carefully checked for dust inside  
the camera and on the surface of the CCD to ensure that it conforms to FUJIFILM standards.  
i Bear in mind also that some types of soiling on the CCD surface cannot be removed even by an  
authorized FUJIFILM dealer.  
Hold down the Lens release button and turn the  
lens in the direction of the arrow.  
Should this occur, you can use features such as the despeckling function provided in the image  
processing software to remedy the problem.  
Using the Camera Overseas  
When traveling overseas, do not place your camera in the check-in baggage. Baggage handling at airports  
may subject baggage to violent shocks, and the camera may be damaged internally even when no external  
damage is visible.  
Continued  
124  
125  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning the CCD  
Set the Exposure mode dial to “M”.  
Hold the camera so that the sun shines on the CCD and check the surface for dust.  
4
8
Surface clean  
Surface soiled  
Clean the CCD yourself.  
Contact a FUJIFILM dealer  
and request CCD cleaning.  
Hold down the Release mode switch unlock button  
and set the Release mode switch to “,” (single-  
frame).  
Turn the camera off and attach a lens or  
body cap to the camera.  
5
6
!
When you turn the camera off, the mirror drops  
down and the shutter closes at the same time.  
Ensure that your fingers are not caught inside the  
camera.  
Hold down both the Synchro mode button and the  
LCD illumination button and turn the camera on.  
Starting CCD cleaning  
Take great care to avoid scratching or damaging the CCD during cleaning, as you will be responsible  
for the possibly high cost of repairs (or replacement) by an authorized FUJIFILM dealer.  
Use a blower (without a brush attached) to remove  
any soiling on the CCD surface.  
1
2
!
Use a blower that does not have a brush attached. Using a  
blower brush to clean soiling from the CCD can scratch the  
CCD surface.  
When you press the shutter button, the mirror flips  
up and the shutter opens and stays open.  
7
Check whether the dust has been removed from the CCD surface.  
The blower has removed the dust (There  
are no oily marks or fingerprints).  
There are oily marks or fingerprints left on the  
CCD that cannot be removed with the blower.  
!
When you release the shutter button, the mirror stays up.  
Proceed to step  
.
3
Turn the camera off and mount the lens or body  
cap on the camera.  
!
When you turn the camera off, the mirror drops down and  
the shutter closes at the same time. Ensure that your fingers  
are not caught inside the camera.  
Continued  
126  
127  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes on the Power Supply  
Cleaning the CCD  
Disposing of Batteries  
Ensure that you have the cleaning equipment ready  
h Cleaning swabs  
Sensor Swab (Photographic Solutions, Inc.)  
For information on suppliers outside Japan, visit the web site listed below  
(http://www.photosol.com/swabproduct.htm).  
h Cleaning fluid  
Applicable Batteries  
h Use only nickel-metal hydride (Ni-MH) batteries with  
this camera. AA size alkaline, AA-size manganese or  
lithium batteries cannot be used.  
When disposing of batteries, do so in accordance with your  
local waste disposal regulations.  
Using the AA-size Ni-MH Batteries  
h As a power source in digital cameras, AA-size Ni-MH  
batteries are superior to alkaline batteries in several  
ways, such as allowing more shots to be taken with  
the camera. However, care must be taken with the  
way Ni-MH batteries are used if their original  
performance is to be maintained.  
Notes on the Batteries  
Incorrect use of the batteries could cause them to leak,  
become hot, ignite or burst. Always observe the  
precautions given below.  
h Do not heat the batteries or throw them into a fire.  
h Do not carry or store the batteries with metal objects  
such as necklaces or hairpins that could come into  
contact with the metal positive and negative poles  
of the battery.  
h Do not expose the batteries to fresh or sea water, and  
take particular care to keep the terminals dry.  
h Do not attempt to deform, disassemble or modify the  
batteries.  
h Do not attempt to peel off or cut the battery casing.  
h Do not drop, strike or otherwise subject the batteries to  
strong impacts.  
h Do not use the batteries that are leaking, deformed,  
discolored or exhibit any other obvious abnormality.  
h Do not store the batteries in very warm or moist  
locations.  
h Keep the batteries out of reach of infant and young  
children.  
h When loading the batteries into the camera, ensure that  
the battery polarity (and ) is as indicated on the  
camera.  
h Do not use new batteries together with used batteries.  
In the case of rechargeable batteries, do not use  
charged and discharged batteries together. Do not use  
batteries of different types or brands together.  
h If you do not intend to use the camera for a long  
period of time, remove the batteries from the camera  
(Note that if the camera is left with the batteries  
removed, the time and date settings are cleared).  
h The batteries may feel warm immediately after being  
used. Before removing the batteries, switch the  
camera off and wait until the batteries cool down.  
h When replacing the batteries, always fit 4 new  
batteries.  
Anhydrous ethanol, EE Cleaner (Olympus)  
Moisten the bottom 5 mm (0.2 in) of the Sensor  
swab evenly with cleaning fluid.  
h Ni-MH batteries left unused in storage for long periods  
can become “deactivated”. Also, repeatedly charging  
Ni-MH batteries that are only partially discharged can  
cause them to suffer from the “memory effect”.  
Ni-MH batteries that are “deactivated” or affected by  
“memory” suffer from the problem of only providing  
power for a short time after being charged. To prevent  
this problem, discharge and recharge them several  
times using the camera’s “Discharging rechargeable  
batteries” function. By repeating this cycle several  
times, the temporary reduction in performance caused  
by “memory” or “deactivation” can be remedied and  
the batteries can be restored to their original  
performance levels.  
Deactivation and memory are specific to Ni-MH  
batteries and are not in fact battery faults. See P.107  
for the procedure for “Discharging rechargeable  
batteries”.  
h To charge Ni-MH batteries, use the battery charger  
(included). Refer to P.21 to make sure that the charger  
is used correctly.  
3
4
!
Do not use the swab when it is dry or not moistened with  
cleaning fluid.  
Slowly and gently wipe one side of the swab just  
once across the full width of the CCD from left to  
right.  
h Do not use the battery charger to charge other  
batteries.  
h Note that the batteries feel warm after being charged.  
h Due to the way the camera is constructed, a small  
amount of current is used even when the camera is  
turned off. Note in particular that leaving AA-size Ni-  
MH batteries in the camera for a long period will  
overdischarge the batteries and may render them  
unusable even after recharging.  
h Ni-MH batteries will self-discharge even when not  
used, and the time for which they can be used may be  
shortened as a result.  
h Ni-MH batteries will deteriorate rapidly if  
overdischarged (e.g. by discharging the batteries in a  
flashlight). Use the “Discharging rechargeable  
batteries” function provided in the camera to discharge  
the batteries.  
h Ni-MH batteries have a limited service life. If a battery  
can only be used for a short time even after repeated  
discharge-charge cycles, it may have reached the end  
of its service life.  
Then wipe the other side of the Sensor swab across the full width of the CCD from left to right  
once more. Do not reuse Sensor swabs.  
5
6
If this does not remove the soiling, repeat steps 3 to 5 with a new Sensor swab or contact an  
authorized FUJIFILM dealer.  
Turn the camera off and mount the lens or body  
cap on the camera.  
Here, ‘new batteries’ refers to Ni-MH (nickel metal  
hydride) batteries that have recently been fully  
recharged together.  
h In cold locations (at temperatures of +10°C/+50°F or  
below), battery performance deteriorates and the time  
for which they can be used shortens markedly. In cold  
conditions, put the batteries in your pocket or a similar  
place to warm them before loading them into the  
camera. If you use a body warmer to warm the  
batteries, ensure that they are not in direct contact  
with the warmer.  
!
When you turn the camera off, the mirror drops down and the  
shutter closes at the same time. Take care to ensure that  
your fingers are not caught inside the camera.  
h Soil (such as fingerprints) on the battery terminals can  
markedly reduce the number of available shots.  
Carefully wipe the battery terminals clean with a soft  
dry cloth before loading the batteries.  
Always use this procedure to clean the CCD. Never clean the CCD in bulb photography mode.  
A current runs through the CCD in bulb photography mode and cleaning could cause damage.  
If any liquid at all leaks from the batteries, wipe the  
battery compartment thoroughly and then load new  
batteries.  
If any battery fluid comes into contact with your  
hands or clothing, flush the area thoroughly with  
water. Note that battery fluid can cause loss of  
eyesight if it gets into your eyes. If this occurs, do  
not rub your eyes. Flush the fluid out with clean  
water and contact your physician for treatment.  
128  
129  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes on the Media  
Notes on the Power Supply  
Image Memory Card  
h The xD-Picture Card may feel warm when it is  
removed from the camera after taking pictures. This  
is normal.  
h Do not put labels on the xD-Picture Card. Peeling  
labels can cause the camera not to work properly.  
Notes on Using the Battery Charger  
AC Power Adapter  
h This Image Memory Card is a new image recording  
media (xD-Picture Card) developed for digital  
cameras. The Image Memory Card consists of a  
semiconductor memory (NAND-type flash memory)  
to record digital image data.  
Always use the AC Power Adapter AC-5VX (sold  
separately). The use of an AC Power adapter other than  
AC-5VX can cause damage to your digital camera.  
h Use the AC power adapter for indoor use only.  
h Plug the connection cord plug securely into the DC  
input terminal of the FUJIFILM Digital camera.  
h Turn off the FUJIFILM Digital camera before  
disconnecting the cord from the FUJIFILM Digital  
camera’s DC input terminal. To disconnect, pull out  
the plug gently. Do not pull on the cord.  
h Do not use the AC power adapter with any device  
other than your camera.  
h During use, the AC power adapter will become hot to  
the touch. This is normal.  
h Do not take apart the AC power adapter. Doing so  
could be dangerous.  
h Do not use the AC power adapter in a hot humid  
place.  
h Do not subject the AC power adapter to strong shocks.  
h The AC power adapter may emit a humming. But this  
is normal.  
h If used near a radio, the AC power adapter may cause  
static. If this happens, move the camera away from the  
radio.  
h Ni-MH batteries or the battery charger itself will  
become warm due to the power stored inside the  
batteries. This is normal and does not indicate a fault.  
Wherever possible, use the battery charger in a well-  
ventilated location.  
h There may be vibration noises from inside the battery  
charger during use. This is normal and does not  
indicate a fault.  
h Do not use the battery charger to charge batteries  
other than Ni-MH batteries.  
h The battery charger could cause interference if placed  
close to a radio during charging. In this event, move  
the radio and charger further apart.  
Using Microdrive  
h Do not use hard-pointed pens to write on the  
Microdrive label.  
The recording process is electrically performed and  
enables erasure of existing image data as well as re-  
recording of new image data.  
h When using a new Memory Card, or a Memory Card  
that has been formatted by a PC, be sure to format  
the card with your digital camera before using it.  
h Do not peel off the Microdrive label.  
h Do not stick additional labels onto a Microdrive.  
h When carrying or storing a Microdrive, keep it in the  
protective case provided.  
h When a Microdrive is used, vibration or impacts  
during image data recording may prevent the image  
data from being recorded correctly. Put the camera  
down carefully when placing it on a desk or table, etc.  
h Do not use Microdrive in CF+ Type II slots that do  
not have an eject function.  
h Take care when handling Microdrive that have been  
used for long periods as they may become hot.  
h Do not place Microdrives close to strong magnetic  
fields.  
Microdrives  
Microdrives are compact, lightweight hard disk drives that  
conform to the CF+ Type II standard. Due to their ample  
capacity for large image data files and their low per-  
megabyte recording cost, Microdrives provide a more  
economical way to save high-resolution image files.  
h Do not touch the connections or contact points on  
rechargeable batteries with other metal objects as this  
can cause a short circuit.  
h Do not leave the battery charger in the following types  
of locations:  
i Extremely humidity or high temperatures, such as  
close to a heating appliance or in direct sunlight  
i Places with strong vibration  
Protecting Your Data  
h Images and movies may be lost or destroyed in the  
following situations. Please note that FUJIFILM  
assumes no responsibility for data that is lost or  
destroyed.  
i In very dusty places  
h The battery charger accepts input voltages of 100-240  
V AC at 50 or 60 Hz and can be used all over the  
world. However, the shape of the plug and socket-  
outlet depends on the country of use. Consult your  
travel agent for details.  
h Keep Microdrive dry.  
h Do not apply strong pressure to the Microdrive cover.  
1. Removal of the memory card or turning the power off  
while the memory card is being accessed (i.e., during  
record, erase, initialization, and playback operations).  
2. Improper handling and use of the memory card by  
the user or third party.  
h Save your important data to another media (i.e., MO  
disk, CD-R, hard disk, etc.).  
Using Compact Flash  
Contact the CompactFlash card manufacturer for  
information on the CompactFlash functions, operation  
details and system requirements.  
Battery Charger BCH-NH2 Specifications  
Card types approved for use with the FinePix S3 Pro  
are listed on the FUJIFILM website.  
h The CompactFlash card may be hot immediately  
after being used in the camera and should be  
handled with care.  
h Do not touch the card contact area with your fingers  
or metal objects.  
h Unused CompactFlash cards should be formatted  
before being used.  
Rated input  
100-240 V AC, 50/60 Hz  
16-21 VA (U.S.A and Canada)  
10 W (other countries)  
Input capacity  
Handling Media (all types)  
Rated output  
DC1.2 V 565 mA (× 4)  
h When inserting the media into the camera, hold the  
media straight as you push it in.  
Applicable batteries AA-size Ni-MH Battery × 4  
Charging time  
Dimensions  
Approx. 255 minutes  
105 mm × 65 mm × 27.5 mm  
(4.1 in. × 2.6 in. × 1.1 in.)  
(L × W × D)  
h Never remove the media or turn the camera off  
during data recording or erasing (media formatting)  
as this could be damaged to the media.  
h Do not bend, drop or otherwise subject the media to  
strong force or shocks.  
h Do not use or store these media in places with  
affected by strong static electricity or electrical noise.  
h Do not use or store media in hot humid places or in  
places where they are exposed to corrosive  
substances.  
Mass (Weight)  
Approx. 95 g (3.4 oz.)  
(excluding batteries)  
0°C to + 40°C  
Using media with a PC  
Operating  
temperatures  
h When taking pictures using a media that has been  
used on a PC, reformat the media using your camera  
for best quality.  
(+ 32°F to + 104°F)  
h When formatting a media, a directory (folder) is  
created. Image data is then recorded in this directory.  
h Do not change or delete the directory (folder) or file  
names on the media because this will make it  
impossible to use the media in your camera.  
h Always use the camera to erase image data on a  
media.  
h To edit image data, copy the image data to the PC  
and edit the copy.  
h Do not copy files other than those that will be used  
by the camera.  
Handling xD-Picture Card  
h When storing xD-Picture Cards, make sure that they  
are kept out of the reach of children. An xD-Picture  
Card could be swallowed cause suffocation. If a child  
swallows an xD-Picture Card, seek medical  
attention or call emergency number right away.  
h Do not expose an xD-Picture Card to shock. Do not  
apply pressure, and avoid bending.  
h
Do not use the xD-Picture Card in a hot or humid  
place.  
h Clean the xD-Picture Card with a soft dry piece of  
cloth when dirty.  
h When carrying or storing an xD-Picture Card, keep it  
in the special protective case.  
h The xD-Picture Card will work well for long time, but  
will sooner or later lose its ability to store and play  
back images or movies. If this happens replace it  
with a new xD-Picture Card.  
h The use of xD-Picture Cards is recommended with  
the FinePix S3 Pro.  
Specifications  
Type  
Image memory card for digital  
cameras (xD-Picture Card)  
NAND-type flash memory  
Temperature:  
0°C to +40°C  
(+32°F to +104°F)  
Memory type  
Conditions for use  
Humidity:  
80% max. (no condensation)  
25 mm × 20 mm × 2.2 mm  
(0.98 in. × 0.79 in. × 0.09 in.)  
(W × H × D)  
Dimensions  
The recording quality cannot be guaranteed when  
xD-Picture Cards other than those manufactured by  
FUJIFILM are used.  
130  
131  
Download from Www.Somanuals.com. All Manuals Search And Download.  
eThe table below lists the warning messages displayed on the  
top display panel or in the viewfinder.  
Warning Displays  
Warning Displayed  
Warning Displayed  
Top display  
panel  
Explanation  
Remedy  
Explanation  
Remedy  
Top display  
Viewfinder  
panel  
Viewfinder  
i CPU Nikkor lens other than G-type i Set lens to minimum aperture.  
is not set to its minimum aperture.  
i Attached flash is not set at TTL i Set the external flash mode to TTL, or set  
The batteries are low on charge or Turn the camera off and replace the  
the camera mechanism has stopped batteries. Then turn the camera back on  
due to cold and cannot take pictures. and try again.  
If this does not resolve the problem, set the  
(blinking)  
(blinking)  
Auto Flash in “P” mode.  
the camera’s exposure mode to “S”, “A” or  
M”.  
Exposure mode dial to “M”, set the focusing  
mode to “M” (Manual focus), press the  
shutter button and then briefly turn the  
camera off.  
(blinking)  
Batteries have no remaining charge. Turn the power off and replace batteries  
with new ones.  
(blinking/lit)  
Non-CPU lens is attached or lens is Attach CPU lens (except IX-Nikkor). With a  
not attached.  
non-CPU lens, set the exposure mode to  
M” and set the aperture with lens’ aperture  
ring.  
In certain cases, due to static electricity or poorly loaded batteries, the FinePix S3 Pro microcomputer  
may turn the camera off, even with fresh, properly installed batteries. For the same reason, the  
operation of camera may not advance properly during either “USB mode” or “IEEE 1394 mode”. In  
each of these cases, to resume operation, simply turn the power off, then turn it on again. Or, remove  
and reinstall the batteries. When this happens, the camera settings may be initialized. Check the  
required camera settings before using the camera.  
(blinking)  
(blinking)  
(blinking)  
Autofocus is not possible.  
Focus manually.  
Overexposure warning (subject is too  
bright).  
i In “P” mode, use ND filter (If the warning  
indication remains after performing above  
remedies in “S” or “A” mode, use ND filter  
as well).  
(lit)  
(lit)  
(lit)  
(lit)  
i In “S” mode, select faster shutter speed.  
i In “A” mode, select smaller aperture  
(larger f-number).  
Underexposure warning (subject is  
too dark.).  
i In “P” mode, use flash (If the warning  
indication remains after performing above  
remedies in “S” or “A” mode, use flash as  
well).  
i In “S” mode, select slower shutter speed.  
i In “A” mode, select larger aperture  
(smaller f-number).  
Electronic  
analog  
exposure  
display  
Subject brightness is beyond When the subject is too bright, use ND filter  
camera’s exposure range.  
and when the subject is too dark, use flash.  
The electronic analog exposure display  
remains blinking when the flash is used.  
(blinking)  
Shutter speed is set to “” in Cancel the “” or select “M” mode.  
S” mode.  
(blinking)  
(blinking)  
(lit)  
Shutter  
speed  
indication  
(blinking)  
Shutter speed faster than sync speed Release the shutter as it is to take a flash  
is selected in “S” or “M” mode.  
picture (Shutter speed automatically shifts  
to 1/180 sec.).  
Flash has fired at full output and Shoot again after confirming focus distance,  
underexposure may have occurred.  
aperture or flash shooting distance range.  
(blinking)  
Set the Exposure mode dial to “M” and  
press the shutter button again. If the  
warning indication remains, or this warning  
appears frequently, contact you FUJIFILM  
dealer.  
Malfunction detected.  
(blinking)  
(lit)  
(blinking)  
The batteries are low on charge or Turn the camera off and replace the  
flat.  
batteries. Then turn the camera back on  
and try again.  
132  
133  
Download from Www.Somanuals.com. All Manuals Search And Download.  
eThe table below lists the warning that are displayed on the  
LCD monitor.  
Warning Displays  
Warning Displayed  
LCD monitor  
Warning Displayed  
LCD monitor  
Explanation  
Remedy  
Explanation  
Remedy  
Displayed for PictBridge.  
No media is inserted.  
Insert a media.  
i Check that the printer is not out of paper  
or out of ink.  
i Turn the printer off briefly and then turn  
it back on.  
i Refer to the user manual supplied with  
your printer.  
i The media is not formatted.  
i The media contact area is soiled.  
i Format the media on the camera.  
i Wipe the contact area on the media with  
a soft dry cloth. It may be necessary to  
format the media. If the message still  
appears, replace the media.  
Displayed for PictBridge.  
Displayed for PictBridge.  
Check that the printer is not out of paper  
or out of ink. Printing automatically  
restarts when the error is cleared. If the  
message still appears after checking,  
press the “MENU/OK” button to restart  
printing.  
i Camera fault.  
i Contact your FUJIFILM dealer.  
i The media contact area is soiled.  
i The media is damaged.  
i The media format is incorrect.  
i Wipe the contact area on the media with  
a soft dry cloth. It may be necessary to  
format the media. If the message still  
appears, replace the media.  
i Refer to the user manual for the printer  
being used and check whether the  
printer supports the JFIF-JPEG or Exif-  
JPEG image format. If not, the printer  
cannot print the images.  
i Was the image data photographed  
using FinePix S3 Pro?  
You may not be able to print some  
images photographed on other  
cameras.  
i Camera fault.  
i Contact your FUJIFILM dealer.  
The media is full.  
Erase some images or use a media that  
has ample free space.  
i The played back file was not i Images cannot be played back.  
recorded correctly.  
i The media contact area is soiled.  
i Wipe the contact area on the media with  
a soft dry cloth. It may be necessary to  
format the media. If the message still  
appears, replace the media.  
This message appears when printing is  
performed from a FUJIFILM printer that  
supports PictBridge. Refer to the Owner’s  
Manual for the printer for details.  
i Camera fault.  
i Contact your FUJIFILM dealer.  
Displayed for PictBridge.  
The frame number has reached  
999–9999.  
1 Insert a formatted media into the  
camera.  
2 Set “RENEW” as the FRAME NO.  
setting in the “SET-UP” menu.  
3 Start taking pictures (The frame  
numbers start from “100-0001”).  
4 Set “CONT.” as the FRAME NO.  
setting in the “SET-UP” menu.  
An attempt was made to use DPOF DPOF printing cannot be used with RAW  
printing for a RAW image file.  
image files.  
An attempt was made to trim a 1M The image cannot be trimmed.  
image or an image shot using the  
RAW setting.  
i The data could not be recorded due i Re-insert the media or turn the camera  
to a media error or a connection  
error between the media and  
camera.  
i The image cannot be recorded as it i Use a new media.  
is too large to fit in the available  
space on the media.  
off and then on again. If the message  
still appears, contact your FUJIFILM  
dealer.  
The image cannot be trimmed.  
i An attempt was made to trim an  
image shot using a camera other  
than FinePix S3 Pro.  
i The image is damaged.  
A protected file was encountered.  
Protected files cannot be erased. Remove  
the protection.  
eThe table below lists the warnings that are displayed on the rear display panel.  
Warning Displayed  
Rear display panel  
Prints were specified for 1000 or The maximum number of frames for which  
more frames in the DPOF frame prints can be specified on the same media  
Explanation  
Remedy  
settings.  
is 999.  
Copy the images for which you want to  
order prints onto another media and then  
specify the DPOF settings.  
The batteries are low on charge.  
Have replacement batteries ready.  
(lit)  
The batteries are flat.  
Replace the batteries.  
(blinking)  
The camera is not connected to PC  
or printer.  
i Check that the USB cable is connected  
correctly.  
i Check that your printer is turned on.  
134  
135  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
eIf you think the camera is faulty, check the following once more.  
Troubleshooting  
Possible causes  
i The batteries are exhausted.  
i The batteries are loaded the wrong way i Reload the batteries correctly.  
round.  
Solutions  
Troubleshooting  
I cannot format the xD- The media is damaged.  
Picture Card or  
CF/Microdrive.  
Possible causes  
Solutions  
Use a new media.  
The camera won’t turn  
on.  
i Load fully charged batteries.  
i The AC power adapter is not connected i Reconnect the adapter correctly and  
I cannot erase all the The frame is protected.  
frames.  
Remove the frame protection.  
correctly.  
plug the adapter plug into the mains  
power outlet.  
Nothing happens when I i Camera malfunction.  
i Remove the power supply (the  
batteries) and then reload them and try  
again.  
Power cuts out during  
operation.  
The batteries are exhausted.  
Load fully charged batteries.  
use  
the  
camera  
switches and dials.  
i The batteries are flat.  
i Fit new batteries.  
Batteries  
quickly.  
run  
out  
i You are using the camera in extremely i Put the batteries in your pocket or  
cold conditions.  
another warm place to heat them and  
then load them into the camera just  
before you take a picture. Note that  
alkaline batteries cannot be used at very  
low temperatures.  
No image appears on i There is no media loaded.  
the color LCD monitor  
when I press the “PLAY” i There is no photography data recorded  
Insert  
a
media that contains some  
photography data.  
button.  
on the media.  
i The battery terminals are soiled.  
i Remove the batteries from the camera  
and wipe the battery terminals with a  
clean, dry cloth before reloading the  
batteries.  
There is no image on i The camera and TV are not connected i Connect the camera and TV correctly.  
the TV screen.  
correctly.  
i “TV” is selected as the TV input.  
i Set the TV input to “VIDEO”.  
Film simulation mode “D-RANGE” is set to “STANDARD” and Set “D-RANGE” to “WIDE” and select the  
i The battery terminals were soiled when i Wipe the battery terminals with a clean,  
the batteries were charged. dry cloth before charging.  
i The batteries were charged after having i Due to their nature, the batteries may  
cannot be selected.  
AdobeRGB is selected as the color space. sRGB color space.  
Can’t print  
with “$” is not selected in USB mode in the Select “$” in USB mode in the SET-UP  
not been used for a long period.  
not be fully charged. Charge and use  
the batteries several times to restore  
them to normal operation.  
PictBridge.  
The camera  
connected to PC when  
the USB mode was set  
to “$”.  
SET-UP menu.  
menu.  
was  
Perform steps 1 to 3 to remove the  
camera from PC.  
i The rechargeable batteries have i Load new fully charged batteries.  
reached the end of their operating lives.  
i The rechargeable batteries (if used) i Use the rechargeable battery  
have become deactivated, or the battery  
capacity has diminished due to the  
memory effect.  
h Windows  
1 The “New Hardware Found” wizard (or  
“Scanner and Camera” wizard)  
appears. If the wizard does not appear,  
proceed to step 3.  
discharging function to restore the  
rechargeable batteries to full capacity.  
2 Click the [Cancel] button.  
3 Disconnect the camera from the PC.  
h Macintosh  
1 The window for locating the driver  
appears. If the window does not  
appear, proceed to step 3.  
2 Click the [Cancel] button.  
3 Disconnect the camera from the  
Macintosh.  
No photograph is taken  
when the shutter button  
is pressed.  
i The focus is not set in AF-S mode i Use AF lock to set the focus and check  
(focus indicator “” not lit).  
that the focus indicator “” is lit before  
taking the shot.  
i Load a media.  
i No media is loaded.  
i The media is full and no further data can i Load a new media or erase some  
be recorded.  
i The media is not formatted.  
i The xD-Picture card contact surface i Clean the xD-Picture card contact  
(the gold-colored area) is soiled.  
frames.  
i Format the media.  
surface (the gold-colored area) with a  
clean dry cloth.  
i The media is damaged.  
i Load a new media.  
i The Auto Power Off function has turned i Turn the camera on.  
the camera off.  
i The batteries are flat.  
i Load fully charged batteries.  
i The camera will not focus.  
i Set the focusing mode to manual (M),  
focus on the subject manually and take  
the picture.  
i An error occurred.  
i Refer to the warning displays on P.132-  
135 and take the appropriate action.  
I can’t use the flash to  
take pictures.  
i The flash is set to Suppressed Flash i The flash pops up.  
mode. (The flash is closed.)  
i You pressed the shutter button while the i Wait until charging is completed before  
flash was charging.  
pressing the shutter button.  
The playback image is  
too dark even though I  
used the flash.  
i The subject is too far away.  
i Your finger was covering the flash.  
i Something is obstructing the flash.  
i Move closer to the subject.  
i Hold the camera correctly.  
i Remove the lens hood.  
The playback image is  
blurred.  
i The lens is dirty.  
i The camera is not focused.  
i The aperture is too small.  
i Clean the lens.  
i Focus the camera correctly (P.34).  
i Take the picture with a slightly larger  
aperture.  
136  
137  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Standard Number of Available Shots per Media  
System  
Model  
The number of available shots varies slightly depending on the type of subject. Also, the discrepancy between the actual  
number of available shots and the standard number grows as the capacity of the media increases.  
Digital camera FinePix S3 Pro  
Number of recorded  
pixels  
Effective pixels  
CCD  
12.34 million (S-pixel: 6.17 million, R-pixel: 6.17 million) pixels  
4256 × 2848  
3024 × 2016  
2304 × 1536  
1440 × 960  
CCD-RAW  
HIGH  
4
3
2
1
`
Large-format (23.0  
Total 12.9 megapixels (S-pixels: 6.45 million; R-pixels: 6.45 million)  
×
15.5 mm) Super CCD SR II with primary color filter  
Quality Mode  
FINE NORMAL FINE NORMAL FINE NORMAL FINE NORMAL  
D-RANGE D-RANGE  
WIDE STANDARD  
Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx.  
Storage media  
File format  
xD-Picture Card (16/32/64/128/256/512 MB)  
CF card and Microdrive TM (FAT32-compatible) (Compatibility is listed on  
Fujifilm website: http://home.fujifilm.com/products/digital/)  
DCF-compliant  
Compressed: Exif Ver.2.21 JPEG, DPOF-compatible  
Uncompressed: CCD-RAW (RAF) 1  
Image File Size  
25 MB  
13 MB 4.7 MB 2.4 MB 3.0 MB 1.5 MB 1.7 MB 880 KB  
1 MB  
520 KB  
DPC-16 (16 MB)  
DPC-32 (32 MB)  
DPC-64 (64 MB)  
DPC-128 (128 MB)  
DPC-256 (256 MB)  
DPC-512 (512 MB)  
Microdrive (340 MB)  
Microdrive (1 GB)  
0
1
1
2
3
6
6
5
10  
20  
8
17  
35  
14  
29  
13  
10  
17  
30  
59  
2
4
13  
26  
53  
107  
73  
220  
26  
21  
42  
36  
72  
61  
120  
241  
484  
967  
671  
1932  
Max. recording resolution  
Number of recorded pixels  
Lens mount  
Focal length  
Sensitivity  
Metering modes  
Exposure control  
Exposure compensation  
Shutter  
Shutter speeds  
Continuous shooting 4  
4256  
4256  
×
×
2848 (12.1 million  
)
5
9
53  
42  
84  
72  
144  
290  
580  
396  
1173  
122  
245  
491  
338  
995  
2848 pixels/3024  
×
2016 pixels/2304  
×
1536 pixels/1440  
×
960 pixels  
10  
20  
13  
41  
19  
39  
27  
81  
107  
214  
146  
437  
85  
169  
339  
232  
698  
146  
292  
200  
597  
Nikon F mount (with AF coupling and AF contacts)  
Approx. 1.5× the nominal focal length of the lens (35mm camera equivalent)  
ISO 100/160/200/400/800/1600 2  
TTL open metering/3D 10-zone Matrix, Center-weighted, Spot  
Program AE, Shutter-priority AE, Aperture-priority AE, Manual exposure  
–3.0 EV to +3.0 EV 1/2 EV step  
Electronically controlled vertical-travel focal-plane shutter  
30 to 1/4000 sec, Bulb X contact: Max. 1/180 sec. 3  
170  
116  
349  
For CCD-RAW files, “`” is displayed as the resolution.  
Input/Output Terminals  
Video output  
Digtal Interface  
DC input  
NTSC/PAL selectable  
USB 2.0 (High-speed), IEEE 1394  
Socket for specified AC Power adapter AC-5VX (sold separately)  
Max. 2.5 frames/sec.: Up to max. 12 frames. (D-range: Standard; JPEG mode)  
Up to max. 7 frames. (D-range: Standard; RAW mode)  
Max. 1 frame/sec.:  
Up to max. 6 frames. (D-range: Wide; JPEG mode)  
Max. 1.4 frames/sec.: Up to max. 3 frames. (D-range: Wide; RAW mode)  
0.5 EV, 1.0 EV, 1.5 EV, 2.0 EV,  
Power Supply and Others  
Power supply  
Auto bracketing  
Focus  
Use one of the following:  
Mode: Single-AF servo, Continuous AF servo, Manual  
AF system: TTL phase difference detection with auxiliary AF flash  
AF frame selection: Single-area AF, Dynamic AF (Dynamic AF Mode with  
Closest Subject Priority is available)  
Automatic scene recognition/Preset (Fine, Shade, Fluorescent (Daylight),  
Fluorescent (Warm White), Fluorescent (Cool White), Incandescent, Custom (2  
settings)  
20 sec./10 sec./5 sec./2 sec.  
Manual pop-up, D-3D Multi-BL flash control, D Multi-BL flash control, Standard  
D-TTL flash control  
Guide No.: 12 (ISO 100-m); Sync. shutter speed: 1/180 sec. or slower  
Front Synchro, Slow Synchro, Rear synchro, Red-eye Reduction and Red-eye  
Reduction Slow Synchro, suppressed flash  
Standard ISO-type with hot-shoe contact (Safty lock provided)  
X contacts only, synchronizing speed: 1/180 sec. or slower  
Equipped with ISO 519 synchro terminal as standard, lock screw provided  
4× AA-size Ni-MH (Nickel-Metal Hydride) batteries  
AC Power Adapter AC-5VX (sold separately)  
i
i
Dimensions and weight  
(W × H × D)  
Camera body dimensions: 147.8 mm × 135.3 mm × 78.5 mm/5.8 in. × 5.3 in. ×  
3.1 in. (excluding lens and attachments)  
Camera body weight: 815 g/28.7 oz (excluding lens, batteries and recording media)  
Weight when shooting: Dependent on the lens used  
Temperature: 0°C to +40°C. (+32°F to +104°F)  
Note that the range for Microdrive is +5°C to +40°C (+41°F to +104°F).  
Humidity: 80% or less (no condensation)  
White balance  
Operating conditions  
Self-timer  
Flash  
Guide to the number of  
available frames for battery  
operation  
Battery Type  
With LCD monitor ON  
Ni-MH batteries 2300 mAh  
Approx. 400 frames  
Flash modes  
According to the CIPA (Camera & Imaging Products Association) standard procedure for measuring  
digital still camera battery consumption (extract):  
When using Ni-MH batteries, use the batteries supplied with the camera. The storage media should  
be xD-Picture Card.  
Shots taken at 23°C, one shot every 30 seconds using a 50mm AF1.4D lens with 1-time AF  
operation, full flash for every other shot, the camera turned off/on every 10 shots and auxiliary AF  
lighting turned off.  
Accessory shoe  
Synchro contacts  
Synchro terminal  
Viewfinder  
Eye-level pentaprism (coverage: Approx. 93% vertical, approx. 95% horizontal),  
h Note: Because the number of available shots varies depending on the level of charge in Ni-MH batteries,  
the figures shown here for the number of available shots using batteries are not guaranteed.  
The number of available shots will also decline at low temperatures.  
dioptric adjustment mechanism, viewfinder magnification approx. 0.8×)  
2.0-inch 235,000-pixels low-temperature polysilicon TFT color LCD panel  
(approx. 100% coverage for playback)  
Release socket built into the shutter release button  
10-pin remote release terminal provided on camera body front  
Color space selection, dynamic range selection, film simulation mode selection,  
framing guideline, frame no. memory, multiple exposure shooting 4, shutter  
button for vertical shooting, live image  
Trimming, Auto Play, multi-frame playback, histogram display, brightness  
warning display  
PictBridge compatibility, Exif Print compatibility, PRINT Image Matching II  
compatibility, language selection (Japanese, English, French, German, Spanish,  
Italian, Chinese), discharging function  
LCD monitor  
Accessories  
Optional accessories  
See P.8  
See P.122-123  
Remote release  
Photography functions  
1: CCD-RAW is a format specific to the FinePix S3 Pro. The enclosed “FinePixViewer” software or the optional Hyper-Utility  
software “HS-V2 Ver. 3.0” is required to interpret the images.  
2: Images shot in high-sensitivity photography (ISO 400 or higher) may appear coarse and may also be affected by noise such  
as white dots.  
3: Images shot with long exposures (about 4 second or longer) may appear coarse and may also be affected by noise such as white dots.  
4: See P.50 for the max. no. of consecutive shots and the shooting intervals for multiple exposure shooting.  
Playback functions  
Other functions  
These specifications and performance data are subject to change without notice. FUJIFILM accepts no liability whatsoever  
for errors or omissions in this manual.  
The color LCD monitor on your digital camera is manufactured using advanced high-precision technology. Even so, up to  
0.01% of the pixels may fail to light or may remain permanently lit. This phenomenon will not appear on the recorded image.  
The operation error may be caused in a digital camera by the strong radio interference (i. e. electric fields, static  
electricity, line noise, etc.).  
138  
139  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Explanation of Terms  
Safety Notes  
Adobe RGB (1998)  
h Make sure that you use your FinePix S3 Pro camera  
correctly, read these Safety Notes and your Owner’s  
Manual carefully beforehand.  
h After reading these Safety Notes, store them in a  
safe place.  
WARNING  
A color space introduced as the working color space for Adobe Photoshop 5.0. AdobeRGB  
encompasses almost all the colors reproduced by CMYK printers and is intended primarily for  
printing applications. It was introduced as “SMPTE-240E” in the RGB settings in Adobe Photoshop  
5.0 and as “Adobe RGB (1998)” in the profile settings from version 6.0 onwards.  
If a problem arises, turn the camera  
off, remove the batteries, disconnect  
and unplug the AC power adapter.  
Continued use of the camera when it is  
emitting smoke, is emitting any unusual  
odor, or is in any other abnormal state  
can cause a fire or electric shock.  
About the Icons  
CCD-RAW  
The icons shown below are used in this document to  
indicate the severity of the injury or damage that can  
result if the information indicated by the icon is ignored  
and the product is used incorrectly as a result.  
Unplug from  
power socket.  
This is the image data prior to signal processing (the reconstruction of the data read in from the  
CCD as an image). Because the signal processing is performed on the computer, high levels of  
control are possible.  
h Contact your FUJIFILM dealer.  
Do not allow water or foreign objects  
to enter the camera.  
If water or foreign objects get inside the  
camera, turn the camera off, remove  
the batteries and disconnect and  
unplug the AC power adapter.  
Continued use of the camera can cause  
a fire or electric shock.  
h Contact your FUJIFILM dealer.  
To reconstruct images, FinePixViewer (on the enclosed CD-ROM) or the Hyper Utility (optional)  
must be installed on your computer.  
This icon indicates that death  
or serious injury can result if  
the information is ignored.  
WARNING  
Color space  
This icon indicates that  
personal injury or material  
damage can result if the  
Refers to the range of colors, expressed as two-dimensional or three-dimensional numerical values,  
that can be reproduced by devices such as cameras, monitors and printers. The sRGB and  
AdobeRGB color spaces are each shown as an xy color chart (a coordinate color space in which  
colors are represented in two dimensions with no brightness value). The range of colors that can be  
expressed by a particular color space is indicated by a triangle imposed on the xy color chart.  
Colors become brighter as they approach the outer edge of the xy color chart. This color  
representation method is capable of showing all the actual colors.  
CAUTION  
information is ignored.  
Do not use the camera in the  
bathroom or shower.  
This can cause a fire or electric shock.  
The icons shown below are used to indicate the nature  
of the information which is to be observed.  
Do not use in the  
bathroom or shower.  
Triangular icons tell you that this  
information requires attention (“important”).  
Never attempt to change or take  
apart the camera. (Never open the  
casing.)  
Do not use the camera when it has  
been dropped or the casing is  
damaged.  
Color Temperature  
Circular icons with a diagonal bar tell you  
that the action indicated is prohibited  
(“Prohibited”).  
Low-temperature light sources, such as a candle flame, are strongly red, while high-temperature  
light sources, such as a gas burner flame, are strongly blue. The color of the light for these  
temperatures is expressed as a color temperature (K = Kelvin). The light of the sun at midday in a  
completely clear sky is taken to be 5500K.  
Do not  
disassemble.  
Filled circles with an exclamation mark tell  
you an action that must be performed  
(“Required”).  
This can cause a fire or electric shock.  
h Contact your FUJIFILM dealer.  
Do not change, heat or unduly twist  
or pull the connection cord and do  
not place heavy objects on the  
connection cord.  
These actions could damage the cord  
and cause a fire or electric shock.  
EV  
A number that denotes Exposure Value. The EV is determined by the brightness of the subject and  
sensitivity (speed) of the film or CCD. The number is larger for bright subjects and smaller for dark  
subjects. As the brightness of the subject changes, a digital camera maintains the amount of light  
hitting the CCD at a constant level by adjusting the aperture and shutter speed.  
When the amount of light striking the CCD doubles, the EV increases by 1. Likewise, when the light  
is halved, the EV decreases by 1.  
h If the cord is damaged, contact your  
FUJIFILM dealer.  
Do not place the camera on an  
unstable surface.  
This can cause the camera to fall or tip  
over and cause injury.  
JPEG  
Joint Photographic Experts Group  
A file format used for compressing and saving color images. The higher the compression rate, the  
greater the loss of quality in the decompressed (restored) image.  
Never attempt to take pictures while  
in motion.  
Do not use the camera while you are  
walking or driving a vehicle.  
White Balance  
Whatever the kind of the light, the human eye adapts to it so that a white object still looks white. On  
the other hand, devices such as digital cameras see a white subject as white by first adjusting the  
color balance to suit the color of the ambient light around the subject. This adjustment is called  
matching the white balance.  
This can result in you falling down or  
being involved in a traffic accident.  
Do not touch any metal parts of the  
camera during a thunderstorm.  
This can cause an electric shock due to  
induced current from the lightning  
discharge.  
Exif Print Format is a newly revised digital camera file format that contains a variety of shooting  
information for optimal printing.  
Do not use the batteries except as  
specified.  
Load the batteries with the and –  
marks.  
140  
141  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Notes  
WARNING  
CAUTION  
Do not heat, change or take apart the  
batteries.  
Do not use this camera in locations  
affected by oil fumes, steam,  
humidity or dust.  
Do not drop or subject the batteries  
to impacts.  
Do not attempt to recharge lithium or  
alkaline batteries.  
Do not store the batteries with  
metallic products.  
This can cause a fire or electric shock.  
Do not leave this camera in places  
subject  
to  
extremely  
high  
temperatures.  
Do not use chargers other than the  
specified model to charge the  
batteries.  
Do not leave the camera in locations such  
as a sealed vehicle or in direct sunlight.  
This can cause a fire.  
Any of these actions can cause the  
batteries to burst or leak and cause fire  
or injury as a result.  
Keep out of the reach of small  
children.  
This product could cause injury in the  
hands of a child.  
Use only the batteries or AC power  
adapters specified for use with this  
camera.  
Do not use voltages other than the  
power supply voltage shown.  
The use of other power sources can  
cause a fire.  
Do not place heavy objects on the  
camera.  
This can cause the heavy object to tip  
over or fall and cause injury.  
Do not move the camera while the  
AC power adapter is still connected.  
Do not pull on the connection cord  
to disconnect the AC power adapter.  
This can damage the power cord or  
cables and cause a fire or electric shock.  
If the battery leaks and fluid gets in  
contact with your eyes, skin or  
clothing. Flush the affected area with  
clean water and seek medical  
attention or call emergency number  
right away.  
Do not use the AC power adapter  
when the plug is damaged or the  
plug socket connection is loose.  
Do not use the charger to charge  
batteries other than those specified  
here.  
This could cause a fire or electric shock.  
The charger is designed for Fujifilm HR-  
AA Ni-MH batteries. Using the charger  
to charge conventional batteries or  
other types of rechargeable batteries  
can cause the battery to leak fluid,  
overheat or burst.  
Do not cover or wrap the camera or  
the AC power adapter in a cloth or  
blanket.  
This can cause heat to build up and  
distort the casing or cause a fire.  
When you are cleaning the camera  
or you do not plan to use the camera  
for an extended period, remove the  
batteries and disconnect and unplug  
the AC power adapter.  
Failure to do so can cause a fire or  
electric shock.  
When discarding or storing batteries,  
cover the battery terminals with  
insulation tape.  
h Contact with other metallic objects or  
batteries could cause the batteries to  
ignite or burst.  
Keep xD-Picture Cards out of the  
reach of small children.  
When charging ends, unplug the  
charger from the power socket.  
Leaving the charger plugged into the  
power socket can cause a fire.  
Because xD-Picture Cards are small,  
they can be swallowed by children. Be  
sure to store xD-Picture Cards out of  
the reach of small children. If a child  
swallows an xD-Picture Card, seek  
medical attention or call emergency  
number.  
Using a flash too close to a person’s  
may temporarily affect the eyesight.  
Take particular care when taking  
pictures of children.  
When an xD-Picture Card is  
removed, the card could come out of  
the slot too quickly. Use your finger  
to hold it and gently release the card.  
Request regular internal testing and  
cleaning for your camera.  
Build-up of dust in your camera can  
cause a fire or electric shock.  
h Contact your FUJIFILM dealer to  
request internal cleaning every 2 years.  
Please note this is not a free of charge  
service.  
142  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Fellowes Paper Shredder DS 1400C User Manual
Fostex Speaker FT207D User Manual
Frigidaire Dishwasher 740 Series User Manual
Fujitsu Printer C145 C037 01EN User Manual
FUNAI CRT Television F3819D User Manual
GE Air Conditioner AZ28E12D User Manual
GE Answering Machine 16174120 User Manual
GE Model Vehicle FVR C9S 2UX Drive Series User Manual
Generac Portable Generator 005802 0 User Manual
Genius Home Theater System TH P3 User Manual