For all customer enquiries or for replacement parts, contact:-
☎
0870 609 1901
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Do not use the product if the electric cables are
damaged or worn.
9. Always check your product is in a safe operating
condition before use.
4. Immediately disconnect from the mains electricity sup-
ply if the cable is cut, or the insulation is damaged.
Do not touch the electric cable until the electrical sup-
ply has been disconnected. Do not repair a cut or
damaged cable. Replace it with a new one.
5. Your electric cable must be uncoiled, coiled cables
can overheat and reduce the efficiency of the product.
6. Do not pull cable around sharp objects.
7. Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.
8. Switch off, remove plug from mains and examine
electric supply cable for damage or ageing before
winding cable for storage. Do not repair a damaged
cable, replace it with a new one. Use only genuine
replacement cable.
Use
1. Use the product only in daylight or good artificial light.
2. Do not use the product when it is raining or in damp
and wet areas.
3. Never use the product in or near water or ponds.
4. Know how to stop the product quickly in an emer-
gency.
5. On slopes, be extra careful of your footing and wear
non-slip footwear.
6. Never pick up or carry the product by the cable.
7. Keep children, pets and bystanders at a safe dis-
tance when using your product.
8. Keep long hair away from air inlet.
9. Keep all inlets clear of debris.
10. Always remain alert.
9. Never carry the product by the cable.
10. Never pull on the cable to disconnect any of the plugs
11. Always wind cable carefully, avoiding kinking.
12. Use only on AC mains supply voltage shown on the
product rating label.
11. Do not attempt to use your product without the fully
assembled debris bag fitted.
12. Never blow debris in the direction of bystanders.
13. Do not overreach. Keep proper footing and balance
at all times.
13. Our products are double insulated to EN60335.
Under no circumstance should an earth be connect-
ed to any part of the product.
14. The cutting head and cutting line continue to rotate
after your product has been switched off.
15. Remove the plug from the mains :-
Preparation
-
-
-
-
-
before removing or replacing cutting line;
before removing or replacing fully assembled debris bag;
before leaving the product unattended for any period;
before clearing a blockage;
before checking, cleaning or working on the appli-
ance;
1. Always wear suitable clothing, gloves, and stout shoes.
2. The use of eye protection is recommended.
3. The use of ear protection is recommended.
4. To prevent dust irritation, the wearing of a face
mask is recommended.
5. Do not wear loose clothing or jewellery that can be
drawn into the air inlet.
-
if the product starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
6. Do not wear clothing with attachments, i.e. toggles
or drawstrings that can be drawn into the air inlet.
7. Inspect your product before each use, especially the
parts of the cutting head. Replace cutting line if
worn or damaged.
8. Do not use if any part is damaged or broken or if
any of the screws are loose. Have it repaired by an
authorised repairer.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
product is in a safe working condition.
2. Replace worn or damaged parts for safety.
3. After use the product should be stored in a safe
place where it is protected from damage.
4. Inspect the collection bag regularly. If the collection
bag becomes worn or damaged, replace.
CABLES
IMPORTANT
1. No earth required. Flymo products are double
insulated to EN60335 and under no circumstances
should an earth be connected to any part of the
product.
•
Use only 1.00mm2 size cable up to 40 metres length
maximum.
Maximum rating :
1.00mm2 size cable, 10 amps 250 volts AC.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
The wires in the mains lead are coloured in accor-
•
THE GARDENVAC IS SUPPLIED WITH CABLE
WIRED DIRECTLY INTO THE PRODUCT.
dance with the following code:
BLUE
BROWN
-
-
NEUTRAL
LIVE
1. Flymo Mains Cables and Extension Cables are
available from your local Husqvarna Outdoor
Products Approved Service Centre.
2. Do not wire an extension cable directly to your prod-
uct yourself. Please contact your local Husqvarna
Outdoor Products Approved Service Centre for further
information on the connectors and kits available.
3. Only use extension cables specifically designed for
outdoor use.
The wire which is coloured BLUE must be connect-
ed to the Terminal which is marked with the letter 'N'
or coloured BLACK.
The wire which is coloured BROWN must be con-
nected to the Terminal which is marked with the let-
ter 'L' or coloured RED.
4. It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
CONNECTORS
IMPORTANT
5. If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only pro-
tect the electrical equipment and are not a safe-
guard against electrocution.
•
Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
•
All Flymo connectors and cables are of splashproof con-
struction. They are not waterproof and must not be left
outside permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail through
pools of water or splashed with water from hose pipes.
If your product is hard wired i.e. non-detachable
mains electric cable, a conversion kit and exten-
sion cable is available from all Husqvarna
Outdoor Products Approved Service Centres
which can be found in your local Yellow Pages.
MAINS PLUG REPLACEMENT
IMPORTANT
•
If the plug supplied is cut off it should be
destroyed. There is an electric shock hazard if a
cut off plug is inserted into a 13 amp socket.
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
C
A
B
D
To Attach Debris Bag to Bag Frame
To Fit the Cutting Line to the Cutting Head (D)
With bag frame on the ground:-
• Switch off and disconnect from the mains
electricity supply BEFORE removing or fitting
the cutting line.
• Handle the cutting line with care - sharp
edges can cause injury.
1. Place the cutting line into the slot in the cutting head
and click into place as illustrated in Figure D.
• Ensure the cutting line is correctly located.
1. Fit first two holes on the plastic trim of the debris
bag to the first two location points on the front of
the bag frame (where debris fin is attached). (A)
2. Fit next hole on the plastic trim to next location
point on bag frame. (B)
3. ...until all holes on the plastic trim of the debris
bag are securely located to bag frame. (C)
• ENSURE THE DEBRIS BAG IS FITTED
SECURELY TO THE BAG FRAME.
• ONLY USE CUTTING LINE SPECIFIED FOR THIS PRODUCT
.
SEE PRODUCT RATING LABEL FOR MODEL DETAILS
E
1
4
2
To Fit Assembled Debris Bag To Product (E)
•
•
Switch off and disconnect from the mains
electricity supply BEFORE REMOVING OR
REPLACING the fully assembled debris bag.
The cutting head and cutting line continue to
rotate after your Gardenvac has been
switched off.
2
IMPORTANT: Do not squeeze the trigger when
fitting the debris bag (E1)
1. Ensure debris fin is horizontal (E2) as illustrated
in fig E.
2. Locate bag frame into clip on the underside of
product. (E3).
3. Lift handle towards product until bag latch
locates and click into place. (E4)
debris fin
3
F
To Remove Debris Bag From Product (F)
1. Gently press bag latch (F1) down. See fig F.
2. Lower handle of bag frame away from product.
3. Move bag frame forward.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly instructions
H
G
Fitting the Handle Bolt (G)
1. Place handle bolt into the location slot on the
K
J
product and slide into place.(G).
2. Repeat on the other side.
Fitting the Handle (H)
1. Locate handle onto handle bolts on each side of
Buckle
the product.
2. Secure handle by turning handle knobs clockwise.
(H)
3. The handle can be adjusted by turning handle
knobs 3 full turns anti-clockwise, moving handle
to position required and re-securing handle as
described in 2.
Fitting The Shoulder Harness (J) & (K).
1. Thread strap through the slots in the handle.(J)
2. Thread strap through the buckle. See fig J. Adjust
as required to ensure the shoulder harness is in the
most comfortable position. See fig. K.
How to Use
WARNING
The use of eye protection is recommended. The use of ear protection is recommended.
To prevent dust irritation, the wearing of a face-mask is recommended. Never point your product at
bystanders. Do not use your product in the rain. Do not leave your product outdoors while it is raining.
IMPORTANT!: YOUR PRODUCT WILL NOT OPERATE UNTIL THE FULLY ASSEMBLED DEBRIS BAG
AND FRAME ARE PROPERLY FITTED.
BEFORE USE: ENSURE THERE ARE NO GAPS BETWEEN THE DEBRIS BAG AND THE PRODUCT
.
• The Gardenvac has 3 modes of operation.
• These can be selected by moving the mode indicator to adjust the nozzle position for blow, vacuum or jet vacuum mode.
• In vacuum and jet vacuum modes the product will shred leaves etc.
BLOW
Position 1 - Blow Mode The Gardenvac will blow debris from
patios, paths, driveways, lawns, bushes, borders etc.
L
Using As A Blower
1. Select position 1 on the mode indicator. See fig L.
2. Point nozzle towards the ground.
3. To start squeeze trigger.
4. Stand back from debris to be cleared.
5. Point nozzle towards the debris and slowly approach.
6. To stop release trigger.
VACUUM
Position 2 - Vacuum Mode
M
In this position your product will pick up leaves, paper, rubbish, cans
etc. IMPORTANT: REMOVE NYLON LINE BEFORE VACUUMING CANS
Using As A Vacuum
1. Select position 2 on the mode indicator. See fig M.
2. Position nozzle slightly above the debris, squeeze the trigger and
move slowly back and forth.
3. Do not force the nozzle into the debris as this will impair perform-
ance.
4. To stop release the trigger.
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use Con’t
JET VACUUM
Position 3 - Jet Vacuum Mode This position is intended to be used
to collect debris which is damp or stubborn. It directs a small jet of
air towards the ground which will loosen stubborn material.
Using As A Jet Vacuum
1. Select position 3 on the mode indicator. See fig N.
2. Position the nozzle above and slightly forward of the debris and
squeeze the trigger.
3. Slowly move the nozzle back over the debris. This allows a jet of air to
lift the debris from the ground.
4. To stop release the trigger.
N
P
Emptying your Gardenvac
• Switch off and disconnect from the mains
electricity supply BEFORE REMOVING OR
REPLACING the fully assembled debris bag.
Emptying Your Gardenvac
1. Remove debris bag as described on page 4.
2. Empty debris bag holding the moulded handle at
the top of the bag and the fabric handle at the
bottom of the bag. (P)
✔
DO
NOT PLACE HANDS IN BAG WHEN EMPTYING,
SHARP DEBRIS CAN CAUSE INJURY
3. Flip the debris fin back into place before re-fitting
as described on page 3.
✕
Caring for your Gardenvac
WARNING Never use water for cleaning your product,
use only a dry cloth. Do not clean with chemicals or
solvents, some can destroy critical plastic parts.
After Using Your Gardenvac (Q1, 2, 3 & 4)
1. Switch off and disconnect from the mains electrici-
ty supply before cleaning your product.
2. Always empty the debris bag.
Q1
Q2
3. Take extra care to clean around the cutting head
and the collection chute.(Q1)
• Take care when cleaning around the cutting
line area - sharp edges can cause injury.
4. Inspect the cutting line and replace if worn or
damaged
5. Using a soft brush remove debris from all air
inlets. (Q2)
Q3
Q5
Q4
Q5
6. Remove dirt and debris from debris fin.with a suit-
able tool. (Q3)
7. Wipe over your product with a soft dry cloth. (Q4)
Replacing the Cutting Line (Q5 & 6)
• Switch off and disconnect from the mains elec-
tricity supply before replacing the cutting line
• Handle the cutting line with care - sharp
edges can cause injury.
1. Remove debris bag from product. See Page 4.
2. Remove cutting line (Q5) and discard safely.
3. If the cutting line becomes broken during use -
use a suitable tool to lever the line out of location.
(Q6).
4. Place the cutting line into the slot in the cutting
head. Ensure the cutting line is correctly located.
See Page 3.
5. Re-fit debris bag to product. See Page 3.
Storing Your Gardenvac
Always store the product in a dry place ensuring the
cable is not likely to be damaged on sharp edges etc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault Finding Hints
Fails To Operate
1. Is the power turned on?
Excessive Vibration
1. The cutting line is damaged - replace with new cutting
2. Is the fully assembled debris bag correctly fitted to the
product?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electrici-
ty supply and consult your local Service
Centre/Dealer/Distributor
line.
2. Ensure the fully assembled debris bag is correctly
fitted to the product.
3. If excessive vibration persists?
Immediately disconnect from the mains electrici-
ty supply and consult your local Service
Centre/Dealer/Distributor
Poor Blowing
Poor Shredding
1. The cutting line is damaged - replace with new cutting
line.
2. TO PROLONG CUTTING LINE LIFE
The Gardenvac has been designed to shred
leaves. If collecting large amounts of any other
debris - remove the cutting line.
3. If poor shredding persists?
1. The air inlets are blocked, clean all air inlets.
2. Mode indicator not in the right position?
3. If poor blowing persists?
Immediately disconnect from the mains electrici-
ty supply and consult your local Service
Centre/Dealer/Distributor
Poor Vacuum/Jet Vacuum
1. The air inlets are blocked, clean all air inlets.
2. Mode indicator not in the right position?
3. If poor vacuuming persists?
Immediately disconnect from the mains electrici-
ty supply and consult your local Service
Centre/Dealer/Distributor
Immediately disconnect from the mains electrici-
ty supply and consult your local Service
Centre/Dealer/Distributor
Service Recommendations
1. We strongly recommend that your product is
serviced at least every twelve months, more often
in a professional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most
Husqvarna Outdoor Products stockists.
4. Your product is uniquely identified by a silver and
black product rating label
5. If you have a problem with your machine contact
your local Approved Service Centre ensuring you
have full details of your product as described on
the product rating label.
6. Should it be necessary for work to be carried out
by your Service Centre, it is important to take your
complete machine including cable and any exten-
sion cables used.
A network of specialist dealers can be found in your
local Yellow Pages. To obtain service on your
Flymo product simply telephone or visit your local
Service Centre. Should you require service under
the terms of our guarantee the Service Centre will
require proof of purchase.
All of the centres listed stock genuine Flymo
Spare Parts.
NOTE: Our Service Repairers act on their own
behalf and are not empowered to commit or
legally bind Husqvarna Outdoor Products in any
manner whatsoever.
Environmental Information
Husqvarna Outdoor Products are manufactured under an Environmental Management System (ISO 14001)
using, where practical, components manufactured in the most environmentally responsible manner, accord-
ing to company procedures, and with the potential for recycling at the end of the products’ life.
•
Packaging is recyclable and plastic components have been labelled (where practical) for categorised
recycling.
•
•
Awareness of the environment must be considered when disposing of ‘end-of-life’ product.
If necessary, contact your local authority for disposal information.
The symbol
on the product or on its packaging indicates that this product may not be treated as house-
hold waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused by inappropriate waste handling of
this product.
For more detailed information about recycling of this product, please contact your local council office, your
household waste disposal service or the shop where you purchased the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture
Failures not covered by guarantee
Replacing Cutting Line.
Failures as a result of not reporting an initial fault.
within the guarantee period, Husqvarna Outdoor Products,
through its Authorised Service Repairers will effect the
repair or replacement to the customer free of charge provid-
ing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
*
*
*
*
Failures as a result of sudden impact.
Failures as a result of not using the product in accor-
dance with the instructions and recommendations con-
tained in this Operator's Manual.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorised by
Husqvarna Outdoor Products.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
*
*
Machines used for hire are not covered by this guaran-
tee.
The following items listed are considered as wearing
parts and their life is dependent on regular mainte-
nance and are, therefore not normally subject to a valid
warranty claim: Cutting Line, Electric Mains cable,
Debris Bag.
*
Caution!
Husqvarna Outdoor Products does not accept liability
under the warranty for defects caused in whole or part,
directly or indirectly by the fitting of replacement parts
or additional parts that are not either manufactured or
approved by Husqvarna Outdoor Products, or by the
machine having been modified in any way
*
This guarantee is additional to, and in no way diminish-
es the customers statutory rights.
Failures due to the following are not covered, therefore it is
important that you read the instructions contained in this
Operator's Manual and understand how to operate and
maintain your machine:
EC Declaration of Conformity
I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP. Certify that the product:-
Category........ Gardenvac
Make.............. Electrolux Outdoor
Products
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using directive
81/1051/EEC as a guide. The maximum A-
weighted sound pressure level recorded at
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using ISO 5349 as
a guide. The maximum weighted root mean
square value of vibration recorded at opera-
tor’s hand position was:-
Conforms to the specifications of Directive operator position under free field semi ane-
2000/14/EEC choic chamber conditions was :-
Identification of Series......See Product Rating Label
Conformity Assessment Procedure....ANNEX VI
Type .......................................................... MEV750/1600 MEV1500/1800/2200/2500
Guaranteed sound power level ............ 93 dB (A)
Measured Sound Power Level ............ 91 dB (A)
Level ........................................................ 88.3 dB (A)
99 dB (A)
99 dB (A)
87.9 dB (A)
Notified Body................I.T.S., Cleeve Road, Leatherhead,
Surrey. KT22 7SB England
2
2
Other Directives:-....98/37/EEC, 89/336/EEC, 73/23/EEC
Value ........................................................ 6.99 m/s
2.89 m/s
3
3
& applicable standards:- EN61000-3-2, EN61000-3-3,
EN55014-1, EN55014-2, EN836, EN60335-1,
EN60335-2-77, IEC60335-1, IEC60335-2-100
Nominal Air Flow .................................... 0.0957 m /s
0.1024 m /s
Weight ...................................................... 4.5 kg
5.1 kg
Newton Aycliffe, 23/01/2006
M. Bowden,
Research & Development Director
Husqvarna Outdoor Products
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - (00) 44 870 609 1901 Fax - (00) 44 870 609 1902
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
5119417-06
Download from Www.Somanuals.com. All Manuals Search And Download.
|