USER GUIDE
AURA® PRO RETAIL
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome
Thank you for making Fishman a part of your acoustic experience. We are proud
to offer you the finest acoustic amplification products available; high-quality
professional-grade tools to empower you to sound your very best. We are
confident Aura Pro will both enhance and inspire your music making.
Troubleshooting
Installation by a qualified professional is strongly recommended.
Should you have any problems, please check with your installer or refer to the
online installation guide for this product. Technical support, troubleshooting tips
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Chart
Once you upload Images into your Aura Pro, use this chart for quick reference.
Image #
Instrument Name Microphone Mic Distance
1
2
3
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Fundamentals
To experience the benefits of Aura, install the Aura Gallery CD
on your computer then upload Images into the Aura Pro pre-
amp. Flip open the preamp and connect the included USB cable
to the side of the preamp.
USB mini jack
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
Before you begin, set the controls
as shown:
1. Plug in • Use a ¼-inch instrument
cable.
2. Tune up • Set Play/Edit switch to
Play. Press Tuner button. When engaged,
Tuner mutes the output. Press again to
exit Tuner.
3. Select an Image • Raise the
Volume and use the Image switch to
browse the Images.
4. Blend in pickup • Turn Blend
control left to mix pickup with Image.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Pickup tone • Set Play/Edit switch to Play and adjust tone controls.
6. Image tone • Set Play/Edit switch to Edit and adjust tone controls. Move
switch back to Play to lock Image tone.
7. Control Feedback
• If feedback occurs, push Phase switch. If feedback recurs when you
change your location, press switch again.
• Push Anti-Feedback button once. Turn up Volume, then either dampen
the strings while tapping the body, or play the troublesome note until
the filter eliminates feedback.
Note: Aura Pro is a programmable preamplifier. To restore factory defaults,
see page 16.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Power
Plug in the guitar, and the Aura Pro switches on. To conserve the battery, remove
the instrument cable from the guitar when the system is not in use. The LEDs in
the tuner display flash once at power-up to tell you the preamp is on.
Low Battery Indicator
When the “Battery” LED flashes once every three seconds, you have approxi-
mately 1.5 hours before the battery is exhausted. Change it at the next opportu-
nity. When the “Battery” LED flashes every half a second, the battery is practically
spent and should be changed immediately.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner
Plug an instrument cable into the endpin jack, move the Play/Edit switch to Play,
and press the Tuner button to turn the circuit on and off. This digital chromatic
tuner accommodates all standard and alternate tunings. When engaged, the
tuner also mutes the output.
Note that the tuner is calibrated to A=440.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
Image
Your Aura Pro is factory loaded with four Images created especially for this
instrument. Each Image corresponds to a different microphone type and
position. Contact the guitar’s manufacturer to identify the microphone
associated each Image.
Volume
For the cleanest noise-free sound, set the Volume as high as possible without
causing your amp or mixer to distort.
Blend
Use the Blend slider to set the balance between the pickup and the Image.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Tone Controls & Play/Edit Switch
The Play/Edit switch lets you EQ the pickup and Image(s) independently.
Pickup EQ
Move the Play/Edit switch to Play and adjust the Bass, Mid and Treble controls.
Switch to Edit and the preamp retains the pickup EQ settings, disengages the
pickup tone controls and enables Image EQ. Return to Play and the preamp
holds the pickup EQ settings until the Bass, Mid or Treble controls are moved
(regardless of the current position of the controls).
Programmable Image EQ
To EQ an Image, move the Play/Edit switch to Edit. The “#” LED flashes to
indicate Edit mode. Move the Blend slider to Aura, select an Image and adjust
the tone controls. You can program EQ for each of the four Images: simply select
another Image and adjust the controls. Switch to Play and the preamp retains the
Image EQ settings, disengages the Image tone controls and enables pickup EQ.
Go back to Edit and the preamp holds the Image EQ settings until the Bass, Mid
or Treble controls are moved (regardless of the current position of the controls).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Phase Switches
Phase (global)
Use the Phase switch to improve bass response at low volume and suppress
feedback at high volume. Push the Phase switch in and out and leave it in the
position most pleasing to your ear. If feedback occurs, push the switch again.
Relative Phase (pickup phase)
To change the character of your blended sound, you may wish to change the
phase of the pickup relative to the Image. There is no “best” position for Relative
Phase and where you set it is a matter of personal taste.
1. Center Blend slider and switch to Edit. The “#” LED flashes to indicate Edit mode.
2. Push the Tuner button to toggle the relative pickup phase.
3. To exit Relative Phase, move the Play/Edit switch to Play.
= default.
You can program different Relative Phase settings for each of the four Images.
Select a different Image and repeat above procedure.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Anti-Feedback
Use this search-and-destroy Anti-Feedback filter in addition to the Phase switch.
1. Push Anti-Feedback button once. The letter “F” in tuner display will flash.
2. Turn up Volume, then either dampen the strings while tapping the body or
play the troublesome note until the feedback begins. The automatic filter will
identify and eliminate the feedback. The circuit will hold this offending frequency
in memory until you push the Measure button again.
To turn the circuit off, push and hold the Anti-Feedback button for five seconds.
Battery Replacement
Pull the small tab at the top of the Aura Pro toward you. The body of the
preamp will swing out, revealing the battery compartment. Observe the polarity
marks on the battery compartment and install a fresh 9V battery. See page 15.
We recommend a lithium battery for extended battery life.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Trim and VU Meter
Adjust this set-and-forget control to accommodate the dynamics of your
playing style. When you set Input Trim to the optimum level, you can play
strongly without distortion and play quietly without hiss.
To Set the Input Trim:
• Unplug the guitar and pull the small tab at the top of the Aura Pro
toward you. Locate the small circular potentiometer on the right side
of the preamp.
• To turn on the VU meter, move the Edit/Play switch to Play and plug in
the guitar while holding the Tuner button. The Tuner display will flash
and the pitch LEDs (two arrows and a circle) will now display the input
level of the preamp.
• Play the instrument strongly and watch the LED display. Use a small
flat-head screwdriver to raise or lower the trim control so all three LEDs
flash occasionally with hard strumming.
• To exit the VU meter, push the Tuner button.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Restore Factory Defaults
1. Unplug the guitar and move the tone controls to the center detent position.
2. Press and hold the Tuner and Anti-Feedback buttons simultaneously.
3. Plug in the guitar. Continue to hold the Tuner/Anti-Feedbackbuttons for three
seconds after you plug in.
4. Release the Tuner/Measure buttons then unplug the guitar to complete
the procedure.
Defaults:
• EQ for all four Images reverts to flat.
• Relative Phase settings return to default state.
• Anti-Feedback frequency is reset to 100Hz.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Specifications
Digital Signal Path:
A/D, D/A conversion:
24-bit
Signal Processing:
32-bit
Typical in-use current consumption @ 9VDC:
Typical 9V lithium battery life:
Typical 9V alkaline battery life:
Nominal output impedance:
Recommended load impedance:
Input Trim gain range:
18mA
54 hours
27 hours
1k Ohm
10k Ohm and up
-6dB to +6dB
+5dBV
-92dBV
97dB
12dB @ 90Hz
12dB @ 1kHz
12dB @ 6kHz
13.5dB
Maximum output level (onset of clipping):
Baseline noise:
Dynamic Range:
Bass control:
Midrange control:
Treble control:
Anti-Feedback: cut depth:
The specifications and information in this manual are subject to change without notice.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
www.fishman.com
Download from Www.Somanuals.com. All Manuals Search And Download.
513-300-150 Rev C 2-09
|