EverFocus DVR EDSR 900 User Manual

INSTRUCTION MANUAL  
EDSR-900  
9 Channel Duplex Digital Video Recorder  
EDSR-1600  
16 Channel Duplex Digital Video Recorder  
V1.02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Precautions  
Safety Precautions  
Warning:  
The lightning flash with an arrowhead symbol, within an  
equilateral triangle, is intended to alert the user to the  
presence of uninsulated ” dangerous voltage” within the  
product’s enclosure that may be of sufficient magnitude to  
constitute a risk of electric shock to persons  
Electrostatic-sensitive device. Use proper  
CMOS/MOSFET handing precautions to avoid  
electrostatic discharge.  
UNPACKING  
Unpack carefully.  
This is electronic equipment and should be  
handled carefully.  
The exclamation point within an equilateral triangle is  
intended to alert the user to presence of important  
operating and maintenance(servicing)instructions in the  
literature accompanying the appliance.  
Check to ensure that the following items are included;  
•1.  
•2.  
•3.  
•4.  
•5  
Digital Video Recorder unit  
User’s manual  
Power Cord  
HDD tray key and screws  
Alarm I/O board  
Warning :  
To prevent fire or shock hazard, do not expose units not  
specifically designed for outdoor use to rain or moisture.  
If an item appears to have been damaged in shipment,  
replace it properly in its carton and notify the shipper.  
Attention:  
Installation should be performed by qualified service personnel  
only in accordance with the National Electrical Code or  
applicable local codes.  
Do not place on uneven or unstable work surfaces.  
Seek servicing if the casing.  
Power Disconnect:  
Units with or without ON-OFF switches have power  
supplied to the unit whenever the power code is inserted  
into the power source; however, the unit is operational  
only when the ON-OFF switch is in the ON position.  
The power cord is the main power disconnect for all units.  
AC100~240V Power Cords  
Note:  
This is a class A product. In a domestic environment this product may cause radio interference  
In which case the user may be required to take adequate measures.  
Note:  
Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later  
reference.  
The information in this manual was current when published. The manufacturer reserves the right to revise  
and improve its products. All specifications are therefore subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safeguards  
Important Safeguards  
Read Instruction---All the safety and operating instructions should be read before the init is operated  
Retain Instructions---The safety and operating instructions should be retained for future reference.  
Heed Warnings—All warnings on the unit and in the operating instructions should be adhered to.  
Follow Instructions—All operating and use instructions should be followed  
Cleaning—Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol  
cleaners. Use a damp cloth for cleaning  
Attachments—Do not use attachment not recommended by the product manufacturer as they may  
cause hazards.  
Water and Moisture—Do not use this unit near water-for example, near a bath tub, wash bowl,  
kitchen sink, or laundry tub, in a wet basement, near a swimming pool, in an  
unprotected outdoor installation, or any area which is classified as a wet location.  
Servicing—Do not attempt to service this unit yourself as opening or removing covers may expose  
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.  
Power Cord Protection—Power supply cords should be routed so that they are not likely to be walked  
on or pinched by items placed upon or against them, playing particular  
attention to cords and plugs, convenience receptacles, and the point where  
they exit from the appliance.  
Object and Liquid Entry—Never push objects of any kind into this unit through openings as they may  
touch dangerous voltage points or short-out parts that could result in a fire or  
electric shock, Never spill liquid of any kind on the unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
1.  
Product Overview…………………………………….………………..…..…..Page 1  
1.1 Main features………………………………………………………………….....…..….1  
1.2 Specifications………………………………………………………………..…………..2  
2.  
3.  
Back panel connections……………………………………………......………3~4  
System connection………………………….………………………………………..5  
Before installation……..……………………………………………………………………..5  
4.  
5.  
6.  
Front panel keypads……………………………………………….…………..…6~7  
Operation…………………………………………………………..……………………..8  
Menu flow………………………………………………………..…………………...9~10  
6.1 Clock setting menu………………………………………...…………………………..11  
6.2 Timer setting menu…………………………………...……………………………..…12  
6.3 Sequence setting menu……………………………..………………………………...13  
6.4 Title setting menu…………………………………..…………………………………..14  
6.5 Covert setting menu………………………………..……………………………….…15  
6.6 Alarm record setting menu………………………..…………………………………..16  
6.7 Motion setting menu…………………………………………………………………...17  
6.8 Record setting menu…………………………………………………………………..19  
6.9 Network setting menu……………………………………………………………….…20  
6.10 Control setting menu………………………………………………………….………21  
6.11 Buzzer setting menu……………………………………………………………….…22  
6.12 Archive setting menu…………………………………………………………………23  
6.13 Matrix setting menu…………………………………………………………………..24  
6.14 System setting menu…………………………………………………………………25  
7.  
8.  
9.  
Recording……………………………………………………………………………..…26  
7.1 Instant recording……………………………………………………………….……….26  
7.2 Alarm recording…………………………………………………………………...…….26  
Playing back…………………………………………………………….………...……27  
8.1 Normal playback…………………………………………………….……………...…..27  
8.2 Search playback………………………………………………….………...……...28~30  
Copy………………………………………………………………….…………….……….31  
9.1 Still image copy…………………………………………………….………….….…….31  
9.2 Copy to movie file………………………………………………….…………...……...32  
9.3 Export event log list..............................................................................................33  
10.  
Monitor Views / Operation..............................................................34  
10.1 Main monitor.......................................................................................................34  
10.2 Call / Matrix monitors..........................................................................................35  
11.  
12.  
Remote Control.............………………………………………..………….…… .36  
11.1 RS-485 remote control …………………………………………..………….……….36  
11.2 IR – remote control ……………………………………………..……….………..…37  
View from Internet/Intranet…………………………………………….…....38~41  
Appendix-A LAN functional specification………..………………………42  
Appendix-B Time lapse recording time table………....…….…..….43~44  
Appendix-C Serial Interface Specifications ……..……………………...45  
1. RS-232 Pin assignment..........................................................................................45  
2. Transmission settings.............................................................................................45  
3. Remote control protocol...................................................................................46~50  
Appendix-D Alarm I/O pin assignment.......……………………………....51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Overview  
1. Product Overview  
The EDSR-900 / EDSR1600 Duplex Digital Video Recorder (DVR) a full-featured DVR designed  
specifically for use in security industry.  
The DVR incorporates all the benefits of digital video recording, is simple to install, and operates  
just like a VCR.  
Highly efficient compression technology and superior resolution of recorded images make the DVR  
stand out from the competition as the best choice for security surveillance.  
The 16 (in) x 5 (out) Matrix Outputs make it powerful for 5 call monitor outputs to be set as you wish.  
The real time audio recording at any video recording speed that makes it as perfect as your  
security demand.  
1.1 Main Features  
? Easy-to-use control panel with common VCR and Multiplexer functions  
? Shuttle/Jog dial for picture-by-picture or fast/slow viewing  
? No tapes to manage, clean or replace  
? Instant retrieval of stored video  
? On-screen setup menu and system timer  
? Ethernet TCP/IP connectivity for remote viewing and controlling  
? Pre-Alarm recording  
? Built-in M-JPEG compression/decompression with configurable video quality  
? Programmed with various time-lapse speeds  
? Two 3.5” IDE Type Hard Disks for storage with Hot-Swap trays  
? RS232 and RS485 for Remote Control  
??IR remote control (optional)  
? Real-Time Live Display for all cameras  
? Variable recording speeds up to 60/50 fields per second for NTSC/PAL  
? Alarm- and motion activated recording  
? Data export to compact flash card  
? 2 channel real time audio recording capabilities  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
1.2 Specifications  
Video Format  
NTSC/PAL  
Video Input  
9 (EDSR900) / 16 (EDSR1600) camera inputs (BNC),1Vp-p/75ohm  
Video Output  
1 BNC video out (1Vp-p/75 ohm) for Main Monitor  
1 S-Video out Mini DIN for Main Monitor  
5 BNC video out (1Vp-p/75 ohm) for Matrix / CALL Monitor output  
9 (EDSR900) / 16 (EDSR1600) video out (1Vp-p/ 75 Ohm)for looping  
Video Compression  
Recording Resolution  
Compact Flash Memory  
Alarm Input  
M-JPEG  
720x484 (NTSC); 720x576 (PAL)  
built-in Compact Flash card slot  
9 (EDSR900) / 16 (EDSR1600) alarm inputs, 25 pin Sub-D  
Alarm Output  
1 alarm output  
EDSR-900: Full, 4, 6, 7, 8, 9, PIP and 2x zoom for Live and Playback  
Video Display modes  
EDSR-1600: Full, 4, 6, 7, 9, 10, 13, 16, PIP and 2x zoom for Live and  
Playback  
Video Loss Detection  
Ethernet  
Yes  
10BaseT Ethernet, RJ45 connector  
Yes  
Event Log  
Hard Disk Storage  
Recording Mode  
Recording Rate  
Playback Rate  
Playback Search  
Setup  
Two 3.5” IDE type, hot- swappable  
Continuous, Timer Schedule, Alarm- or Motion Recording  
Up to 60/50 fields per second for NTSC/PAL  
Up to 60/50 fields per second for NTSC/PAL  
By Date/Time, Event, Segment  
On screen display setup (OSD)  
Menu Driven  
User Interface  
User Input Device  
Timer  
Front Panel Keypad  
Built-in real time clock  
Watch Dog Timer  
RS-232  
Yes  
9-pin female D-Sub  
RS485  
2 x RJ45 Socket  
Audio  
2 x Audio In / Out Cinch 500mV max., 10 KOhm impedance  
430mm (W) x 88mm (H) x 300 (D)  
Dimension  
Power Consumption  
40W max.  
AC100~240V  
Power Source  
0°C ~ 40°C  
Operating Temperature  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Back Panel Connections  
2. Back Panel Connections  
6
1
2
3
5
4
EDSR-900  
14  
13  
11  
12  
7
9
10  
8
3
1
6
2
5
4
EDSR-1600  
14  
13  
11  
12  
7
9
10  
8
1
2
ON/OFF:  
AC100~240V  
Main on/off switch.  
power socket.  
3
Matrix Outputs: These connectors are used for additional 4 programmable Call monitors.  
With these outputs, there are totally 5 programmable call monitors.  
These monitors can only display full screen as regular call monitor.  
4
5
VIDEO IN:  
BNC-sockets for composite signal video inputs, automatic 75 Ohm  
termination (EDSR-900: 1 ~ 9, EDSR-1600: 1 ~ 16).  
VIDEO OUT:  
Loop through video outputs for each input channel.  
(EDSR-900: 1 ~ 9, EDSR-1600: 1 ~ 16)  
6
7
CALL MONITOR: BNC-socket Call (Spot) Monitor, composite signal. (Full screen display only)  
MAIN MONITOR: BNC-socket main monitor, composite signal. Main monitor provides  
Full sreen, Multiscreen, Setup.  
8
9
S-VIDEO:  
Mini-DIN socket main monitor, S-Video signal. Main monitor provides  
Full sreen, Multiscreen, Setup.  
AUDIO IN :  
2 x Cinch socket audio input 500 mV max., 10 KOhm impedance.  
2 x Cinch socket audio output 500 mV max. at 10 KOhm  
AUDIO OUT:  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Back Panel Connections  
10  
ALARM I/O: (Refer pin assignment in Appendix-C, Page 44)  
ALM-INPUT : Normally Open (N.O) or Normally Close (N.C) type alarm sensor input.  
The Alarm Input can be selected as N.O or N.C input in the setup  
menu. When an alarm occurs, alarm recording will automatically start.  
ALM-OUTPUT : Two-way contact relay alarm output. In normal condition, this N.C. contact  
shorted to ALM-COM. In alarm status, it is open between ALM-NC and  
ALM-COM, N.O. is shorted to ALM-COM.  
11  
RS232 connector : D-Sub 9 pins connector to RS232 ports for remote control.  
RS485 connector : 2 x RJ-45 connectors for RS-485 remote control, high impedance  
Supported are keyboards KS-KBK, KS-KBJ.  
12  
Maximum units in RS-485 network are 32.  
Following EverFocus products are compatible in RS-485 network:  
- DVR´s  
EDSR100H, EDSR100M, EDSR400, EDSR400H,  
EDSR400M, EDSR900, EDSR1600  
- Keyboards KS-KBJ (with 3 - axis Joystick, DVR and telemetry control)  
KS-KBK (only DVR control)  
LAN Connector : RJ-45 LAN connector for internal 10MBit LAN interface.  
FAN: Cooling fan, do not cover.  
13  
14  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Connection  
3. System Connection  
The installations described below should be made by qualified service personnel or system installers.  
Before Installation  
Please refer to the following diagram for the system connections.  
EDSR 900: Camera 1~9 / EDSR-1600: Camera 1 ~ 16  
~
Alarm In/Out  
Audio Input  
RS232  
Ethernet  
(camera Audio Out)  
Audio Out  
(To Speaker)  
RS485  
Matrix Outputs  
4 CALL Monitors  
(Optional)  
Remote Keyboard(s)  
KS-KBJ / KS-KBK  
(optional)  
MAIN Monitor  
CALL Monitor  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel Keypads  
4. Front Panel Keypads  
12  
2
EDSR-900  
1
11  
10  
22  
6
9
8
3
4
7
5
15  
18  
19  
13  
14  
16  
17  
20  
21  
2
EDSR-1600  
1
SHUTTLE Ring and JOG Dial  
SHUTTLE : In Playback mode, turn the shuttle ring to fast  
forward/rewind the picture (600X maximum).  
In Pause mode, turn the shuttle dial to slow forward/rewind  
the picture (1/32 maximum).  
JOG :  
In Pause mode, turn the jog dial to step forward/rewind the Picture.  
In Menu mode turn the jog dial to select options.  
2
3
CHANEL KEYS:.  
Press these keys (EDSR-900: 1 ~ 9, EDSR-1600: 1 ~ 16) to display video image in full screen  
format, the picture of the corresponding camera will fill the whole screen of the monitor display.  
MENU: Press this key to enter Setup Menu (Please refer to page 9~25 for details).  
4
5
CALL: Press this key to show picture of assigned camera to desired call monitor.  
SEQ : Press this key to enter the auto sequential switching mode for main monitor.  
ZOOM: Press this key while viewing the full screen image to display X2 zoom-in picture. To move  
the zooming area, use JOG to move from left to right. Press ENTER for changing vertical /  
horizontal movement.  
6
MODE: Switch Full, 4, 6, 7, 8, 9, (10, 13 and 16 for EDSR-1600 only), PIP (picture in picture)  
multiscreen for Live and Playback.  
7
8
SELECT: In Full screen mode: press this key to pop-up dialog as below:  
DISPLAY SETTING MENU  
CHANNEL 01  
BRIGHTNESS  
CONTRAST  
COLOR  
HIT SELECT TO DISCARD CHANGE  
HIT MENU TO SAVE AND EXIT  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel Keypads  
In Fullscreen mode this menu allows color adjustment for each video channel, all channels  
are separately adjustable.  
The selected item will show in red color bar. Use JOG to increase or decrease the value.  
Press ENTER to confirm and move to next item. After finished setting, press SELECT key to  
discard change or press MENU key to save and exit the dialog.  
In Multiscreen mode:  
In Multiscreen mode the SELECT key allows to define cameras in all multiscreen views.  
Press SELECT. At the upper left camera in multiscreen appears “SELECT”.  
Use the numeric camera keys to select a camera.  
Press ENTER to switch in the multiscreen.  
Press SELECT to exit this setting.  
Note: Every camera can be selected only once for a multiscreen view.  
Display: Press this key to switch ON/OFF for camera title, date/time and HDD status.  
9
Hold this key longer than 2 seconds for displaying the event log list.  
10  
11  
12  
Compact Flash Card Slot: Insert a Compact Flash Card for archiving video.  
Hard Disk Trays: 2 x Hard Disk holder for 3.5” HDD.  
HDD locks: Turn on HDD power and protection from taking out the HDD without authority.  
13  
14  
REC: Press this key to start recording.  
STOP: Press this key to stop recording or playing back.  
15  
16  
17  
18  
PLAY: Press this key to stat playing back recoded picture (Please refer to page 27 for details).  
PAUSE: Press this key to pause the playback picture.  
SEARCH: Press this key to enter the Search Menu (Please refer page 28~30 for details).  
COPY: Under PAUSE or PLAYBACK, Press this key to start copying still picture or video  
stream into Compact Flash card (Please refer page 31~33 for details).  
19  
ENTER: Press this key to enter sub-menu or confirm setup. When there is Alarm, Motion  
or Video Loss occurs, press this key for alarm reset. The Event Log Dialog will show on  
the display, then follow the instruction to continue.  
20  
21  
22  
LEDs: LEDs for HDD1, HDD2 , ALARM and LAN access (from left to right).  
IR Remote Controller receiver  
LCD Panel: To display Date/Time, Recording/Playback and HDD status.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
5. Operation  
(1) Insert a HDD (IDE) for Video Storage  
Insert one or two HDD (3.5” IDE) for Video Storage.  
The HDD should be set as Cable Select.  
(Normally the default setting of HDD is Master)  
Note: After hard disk case is inserted into the hard disk tray, be sure to turn the tray key  
in lock position.Otherwise, HDD will not be detected.  
ATTENTION: Changing HDD´s and switching on HDD´s is not allowed in record mode!  
(2) Connect cable for video/audio input and video/audio out,  
The detail connection is described in SYSTEM CONNECTION.  
(3) Switch Power On  
The LCD panel in the front panel will light when you switch on the power.  
(4) Press MENU key to enter SET UP MENU.  
Once inside the main menu you will find there are 14 set up pages as below:  
Selected item will be surrounded by a white block.  
MENU  
MAIN MENU  
CLOCK  
TIMER  
SEQUENCE  
TITLE  
COVERT  
ALARM  
MOTION  
RECORD  
NETWORK  
CONTROL  
BUZZER  
ARCHIVE  
MATRIX  
SYSTEM  
(5)  
Turn the JOG dial clockwise or counter-clockwise to select the item,  
press ENTER key for detail set up for each item.  
(6) Press MENU again to leave the set up menu.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU flow  
6. MENU FLOW  
Columns in brackets () only valid for EDSR-1600  
MOTION  
( See page 17 )  
TITLE  
( See page 14 )  
CLOCK  
( See page 11 )  
TITLE SETTING MENU  
CH OP SEN  
DURATION  
CLOCK SETTING MENU  
CH TITLE  
1
2
3
4
5
6
7
8
9
CH01:_ _ _ _ _  
CH02:_ _ _ _ _  
CH03:_ _ _ _ _  
CH04:_ _ _ _ _  
CH05:_ _ _ _ _  
CH06:_ _ _ _ _  
CH07:_ _ _ _ _  
CH08:_ _ _ _ _  
CH09:_ _ _ _ _  
1
2
3
4
5
6
7
8
9
ON HIGH 07 SECS  
:
:
2003/07/04 FRI  
13:01:02  
DATE  
TIME  
ON HIGH 07 SECS  
ON HIGH 07 SECS  
ON HIGH 07 SECS  
ON HIGH 07 SECS  
ON HIGH 07 SECS  
ON HIGH 07 SECS  
ON HIGH 07 SECS  
ON HIGH 07 SECS  
MENU LANGUAGE: ENGLISH  
VIDEO SYSTEM: NTSC  
VERSION: 0.96 11/23  
(10 CH010:_ _ _ _ _ )  
(11 CH011:_ _ _ _ _ )  
(12 CH012:_ _ _ _ _ )  
(13 CH013:_ _ _ _ _ )  
(14 CH014:_ _ _ _ _ )  
(15 CH015:_ _ _ _ _ )  
(16 CH016:_ _ _ _ _ )  
(10 ON HIGH 07 SECS)  
(11 ON HIGH 07 SECS )  
(12 ON HIGH 07 SECS)  
(13 ON HIGH 07 SECS)  
(14 ON HIGH 07 SECS)  
(15 ON HIGH 07 SECS)  
(16 ON HIGH 07 SECS)  
TIMER  
( See page 12 )  
TIMER SETTING MENU  
COVERT  
( See page 15 )  
RECORD  
( See page 19 )  
WEEK START STOP SPEED SET  
RECORD SETTING MENU  
COVER SETTING MENU  
CH OP  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
23:59 60 IPS OFF  
NORMAL RECORD  
1
2
3
4
5
6
7
8
9
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SPEED  
: 60 IPS  
QUALITY  
DISK FULL  
: STANDARD  
: REWRITE  
ALARM RECORD  
OPERATION  
SPEED  
: 60 IPS  
QUALITY  
ON  
: STANDARD  
(10 OFF)  
(11 OFF)  
(12 OFF)  
(13 OFF)  
(14 OFF)  
(15 OFF)  
(16 OFF)  
PRE-ALARM RECORD  
OPERATION  
ON  
SEQUENCE  
( See page 13 )  
NETWORK  
( See page 20)  
ALARM  
( See page 16 )  
SEQUENCE SETTING MENU  
CH OP DWELL  
CH OP TYPE DURATION  
NETWORK SETTING MENU  
1
2
3
4
5
6
7
8
9
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
1
2
3
4
5
6
7
8
9.  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS)  
05 SECS)  
05 SECS)  
05 SECS)  
05 SECS)  
05 SECS)  
IP ADDRESS  
NET MASK  
GATEWAY  
:192.168.010.005  
:255.255.255.000  
:192.168.010.001  
USER-MANE PASSWORD LEVEL  
GUEST  
GUEST  
GUEST  
GENERAL  
SUPER  
(10 ON 03 SECS)  
(11 ON 03 SECS)  
(12 ON 03 SECS)  
(13 ON 03 SECS)  
(14 ON 03 SECS)  
(15 ON 03 SECS)  
(16 ON 03 SECS)  
GENERAL  
SUPER  
GENERAL  
SUPER  
(10 ON N.O  
(12 ON N.O  
(13 ON N.O  
(14 ON N.O  
(15 ON N.O  
(16 ON N.O  
RST ON N.O  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU flow  
Columns in brackets () only valid for EDSR-1600  
MATRIX  
MATRIX  
( See page 24 )  
CONTROL  
SUB-MENU  
( See page 21)  
MONITOR-3 SETTING MENU  
MATRIX SETTING MENU  
CH DWELL EVENT  
CONTROL SETTING MENU  
1
2
3
4
5
6
7
00  
00  
(00  
(00  
(00  
(00  
(00  
(00  
(00  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE)  
07 SECS NONE)  
07 SECS NONE)  
07 SECS NONE)  
07 SECS NONE)  
07 SECS NONE)  
07 SECS NONE)  
MONITOR-0  
MONITOR-1  
MONITOR-2  
MONITOR-3  
MONITOR-4  
: 9600 BPS  
: 1  
: NONE  
: 8  
RS232 BAUD RATE  
RS232 STOP BIT  
RS232 PARITY  
RS232 DATA BIT  
: 9600 BPS  
: 1  
: NONE  
: 8  
RS485 BAUD RATE  
RS485 STOP BIT  
RS485 PARITY  
RS485 DATA BIT  
: 1  
RS232/RS485 ID  
SYSTEM  
( See page 25 )  
BUZZER  
( See page 22 )  
SYSTEM SETTING MENU  
BUZZER SETTING MENU  
BUZZER  
:
ENABLE  
PLAY WITH AUDIO-1: ON  
PLAY WITH AUDIO-2: ON  
RECORD-IN : ON  
ALARM-IN : ON  
MOTION-IN : ON  
DISK FULL : ON  
VIDEO LOSS: ON  
MULTI-EVENT DWELL: 02 SECS  
PASSWORD ENABLE: DISABLE  
PASSWORD:  
888888  
DISK RENEW:  
NO  
TIMER  
: ON  
SYSTEM UPDATE: NO  
LOAD DEFAULT: NO  
ARCHIVE  
( See page 23 )  
ARCHIVE SETTING MENU  
: 720 X 480  
: ON  
PICTURE SIZE  
TIME STAMP  
: TOP  
: ON  
: TOP  
TIME STAMP POS  
WATER MARK  
WATER MARK POS  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.1 CLOCK SETTING MENU  
CLOCK SETTING MENU  
: 2003/07/04 FRI  
: 13:01:02  
MENU LANGUAGE  
VIDEO SYSTEM  
DATE  
TIME  
: ENGLISH  
: NTSC  
VERSION: 0.79 11/23  
In CLOCK/LANGUAGE SETTING MENU , we define:  
(1) DATE : Current date, format: YYYY/MM/DD  
Year: 2000 ~ 2099, Month: 01~ 12, Date: 01~31, Week: Sunday~Saturday  
(2) TIME : Current time, format: HH:MM:SS  
Hour: 00 ~ 23, Minute : 00 ~ 59, Second: 00 ~ 59  
(3) MENU LANGUAGE: ENGLISH or Others  
(4) VIDEO SYSTEM: Factory default setting depend on machine “NTSC” or “PAL” .  
(5) VERSION: Current S/W revision and release date.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.2 TIMER SETTING MENU  
TIMER SETTING MENU  
WEEK START  
STOP SPEED SET  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
SUN  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
00:00  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
23:59 50 IPS OFF  
In TIMER SETTING MENU we define automatic timer controlled records.  
Timer records can be defined for 12 individual start and end times.  
(1) WEEK: This select the week day for the timer to record on schedule.  
DLY means daily record.  
(2) START: Enter the start time for timer recording.  
(3) STOP: Enter the end time for timer recording.  
NOTE: The recorder records till the end of the minute, which is set here.  
EXAMPLE: START 07:00 END 08:00  
The recorder records from 07:00:00 till 08:00:59  
Each day has to be set separately:  
EXAMPLE: Daily record from 20:00 till next day 07:00  
WRONG: DLY START 20:00 STOP 07:00  
CORRECT: DLY START 20:00 STOP 23:59  
DLY START 00:00 STOP 06:59  
(4) SPEED : Select recording speed. Maximum 60 (NTSC) / 50 (PAL).  
(5) SET: Set “ON” when using timer recording.  
Set “OFF” when not using timer recording.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.3 SEQUENCE SETTING MENU  
SEQUENCE SETTING MENU  
CH OP DWELL  
1
2
3
4
5
6
7
8
9
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
ON 03 SECS  
(10 ON 03 SECS)  
(11 ON 03 SECS)  
(12 ON 03 SECS)  
(13 ON 03 SECS)  
(14 ON 03 SECS)  
(15 ON 03 SECS)  
(16 ON 03 SECS)  
Columns in brackets () only valid for EDSR-1600  
In the SEQUENCE SETTING MENU, we define for MAIN Monitor  
(1) CH (Channel): Input channels. 1~9 for EDSR-900, 1~16 for EDSR-1600.  
(2) OP (Operation): ON includes the camera in the sequence, OFF skips the camera in the  
sequence.  
(3) DWELL (DWELL TIME) : Dwell Time is individual adjustable for each channel. The dwelling  
time for the sequencer can be set between 0-99 seconds.  
Note: Sequences for Call monitors are defined in MATRIX menu.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.4 TITLE SETTING MENU  
TITLE SETTING MENU  
CH TITLE  
1
2
3
4
5
6
7
8
(9  
CH01:_ _ _ _ _  
CH02:_ _ _ _ _  
CH03:_ _ _ _ _  
CH04:_ _ _ _ _  
CH05:_ _ _ _ _  
CH06:_ _ _ _ _  
CH07:_ _ _ _ _  
CH08:_ _ _ _ _  
CH09:_ _ _ _ _  
(10 CH010:_ _ _ _ _ )  
(11 CH011:_ _ _ _ _ )  
(12 CH012:_ _ _ _ _ )  
(13 CH013:_ _ _ _ _ )  
(14 CH014:_ _ _ _ _ )  
(15 CH015:_ _ _ _ _ )  
(16 CH016:_ _ _ _ _ )  
Columns in brackets () only valid for EDSR-1600  
In TITLE SETTING MENU , we define:  
The Title Setting Menu allows you to assign a title to each camera input.  
Title with up to 12 characters is supported in each channel.  
The available alphanumeric characters are:  
0,1,2,3,4,5,6,7,8,9,  
A,B,C,D,…X,Y,Z.  
/ ( ) . - * & @ : ”  
Default setting is CH01~CH09 for EDSR-900, CH01~Ch16 for EDSR1600.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
MENU  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.5 COVERT SETTING MENU  
COVERT SETTING MENU  
CH OP  
1
2
3
4
5
6
7
8
9
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
(10 OFF)  
(11 OFF)  
(12 OFF)  
(13 OFF)  
(14 OFF)  
(15 OFF)  
(16 OFF)  
Columns in brackets () only valid for EDSR-1600  
In COVERT SETTING MENU , we define:  
The covert setting menu allows you hide the desired camera on the  
display in a blue background. Change setting to ON for covering camera.  
Camera is not visable in Live and Playback mode, unless this function is  
deactivated in COVERT menu.  
Default setting is OFF for all cameras.  
Note: With network access a covert camera is only visable for users  
with “ADMIN” password level. For users with “GENERAL” and  
“GUEST” level the covered camera is not visable.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
MENU  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.6 ALARM RECORD SETTING MENU  
ALARM SETTING MENU  
CH OP TYPE DURATION  
1
2
3
4
5
6
7
8
9
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
ON N.O  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS  
05 SECS)  
05 SECS)  
05 SECS)  
05 SECS)  
05 SECS)  
05 SECS)  
(10 ON N.O  
(12 ON N.O  
(13 ON N.O  
(14 ON N.O  
(15 ON N.O  
(16 ON N.O  
RST ON N.O  
Columns in brackets () only valid for EDSR-1600  
In ALARM RECORDING MENU, we define  
(1) CH (Alarm input) : Select alarm input or RST for alarm reset input.  
(2) OP (OPERATION) : ON : Records when alarm occurs.  
OFF : No reaction when alarm occurs.  
(3) TYPE : Select alarm type:  
N.C. : Normally Closed with time out function counting from alarm start  
(set in DURATION)  
N.C. + TRANS : Normal Closed, alarm duration as long as contacts is  
active + timeout (set in DURATION)  
N.O. : Normal Open with time out function counting from alarm start  
(set in DURATION)  
N.O. + TRANS: Normal Open, alarm duration as long as contact is  
active + timeout (set in DURATION)  
(4) DURATION : Timeout duration time for each event. 0~99 seconds adjustable.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.7 MOTION SETTING MENU  
MOTION SETTING MENU  
CH OP SEN  
DURATION  
1
2
3
4
5
6
7
8
9
ON HIGH 05 SECS  
ON HIGH 05 SECS  
ON HIGH 05 SECS  
ON HIGH 05 SECS  
ON HIGH 05 SECS  
ON HIGH 05 SECS  
ON HIGH 05 SECS  
ON HIGH 05 SECS  
ON HIGH 05 SECS  
(10 ON HIGH 05 SECS)  
(11 ON HIGH 05 SECS)  
(12 ON HIGH 05 SECS)  
(13 ON HIGH 05 SECS)  
(14 ON HIGH 05 SECS)  
(15 ON HIGH 05 SECS)  
(16 ON HIGH 05 SECS)  
Columns in brackets () only valid for EDSR-1600  
In the MOTION RECORD SETTING MENU, we define  
(1) CH (Channel) : video input channel  
(2) OP (Operation) : Default: OFF  
ON: The device will respond recording when motion occurs.  
OFF: The device will not respond recording when motion occurs.  
(3) SEN (Sensitivity) : HIGH, MIDDLE or LOW adjustable. Default: MIDDLE.  
(4) DURATION: Duration time tor motion record and Alarm Out relay.  
0~99 seconds adjustable. Default: 05 seconds.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
(5) HIT 1-9/16 TO MANUAL EDIT:  
Use the numenic keys (1~9 for EDSR-900 / 1~16 for EDSR-1600) to  
select a camera for setting the detection areas.  
The selected camera appears with a 16 x 12 grid (detection zones):  
HIT ENTER TO SELECT MODE  
USE JOG TO TOGGLE ON/OFF  
HIT MENU TO EXIT  
ENTER  
jumps to the next detection field.  
JOG wheel switches zone ON – active (area filled) or OFF – inactive (area  
empty) for motion detection.  
MENU  
key exits area setting and jumps back to MOTION SETUP MENU.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
MENU  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.8 RECORD SETTING MENU  
RECORD SETTING MENU  
NORMAL RECORD  
: 50 IPS  
SPEED  
: STANDARD  
: REWRITE  
QUALITY  
DISK FULL  
ALARM RECORD  
OPERATION  
SPEED  
ON  
: 50 IPS  
: STANDARD  
QUALITY  
PRE-ALARM RECORD  
ON  
OPERATION  
In NORMAL RECORDING MENU, we define  
(1)  
NORMAL RECORD:  
SPEED : To set the normal recording speed. Maximum 60 (NTSC) / 50 (PAL).  
QUALITY: Video recording quality setup for setting the quality of the video picture by  
selecting a compression rate. There are six quality levels for recording  
LOWER  
LOW  
BASIC  
: 15 KB  
: 19 KB  
: 23 KB  
STANDARD : 27 KB  
HIGH : 31 KB  
SUPERIOR : 35 KB  
DISK FULL: Set REWRITE or STOP when HDD is full.  
(2)  
ALARM RECORD (for Alarm In and Motion detection):  
OP (Operation): Select ON or OFF to activate alarm recording or not.  
SPEED : To set the alarm and motion recording speed. Maximum 60 (NTSC) / 50  
(PAL).  
QUALITY: Video recording quality setup, this item lets you set the quality of the video  
picture by selecting a compression rate.  
NOTE: The record rates are for the total system: The single camera record rate is:  
Camera record rate = System record rate / Number of connected cameras  
Example: Record Rate 50 Ips, 6 connected cameras: ~ 8,3 Ips / camera  
(3)  
PRE-ALARM RECORD: (with Alarm In and Motion)  
Pre – Alarm duration is depending on record quality (about 8-15 seconds).  
OP (Operation): Select ON or OFF to activate pre-alarm recording or not .  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.9 NETWORK SETTING MENU  
NETWORK SETTING MENU  
IP ADDRESS  
: 192.168.010.005  
: 255.255.255.000  
: 192.168.010.001  
: 00:5A:56:A3:87:1A  
NET MASK ADDRESS  
GATEWAY ADDRESS  
MAC ADDRESS  
USER-NAME  
PASSWORD  
GUEST---  
GENERAL-  
SUPER---  
LEVEL  
GUEST---  
GENERAL-  
SUPER---  
GUEST---  
GENERAL-  
SUPER---  
In the NETWORK SETTING MENU, we define  
(1)  
(2)  
IP ADDRESS : Assign an fixed IP address for this unit, for example:192.168.010.005  
NET MASK ADDRESS: Assign a subnet mask of the network for this unit, for  
example:255.255.255.000  
(3)  
(4)  
GATEWAY ADDRESS: Assign a default gateway for this unit, for  
example:192.168.010.001  
MAC ADDRESS:  
Display of fixed hardware address of the network interface.  
Note: After changing network settings, screen will comes up as following:  
Network setting……………………………….  
Please reboot to effect network setting  
After restart of EDSR the new network settings are activated.  
(5)  
USER-NAME PASSWORD LEVEL  
The Login name and password are used to establish a network connection to the unit.  
The PASSWORD setup allows the administrator to set the new Login name and password  
with access level “SUPER”,”GENERAL” or “GUEST”.  
The system allows up to four users connected at same time with different access levels.  
ADMIN ” : can view live/playback video, covert cameras and control all operation/setup.  
GENERAL”: can view live and playback video.  
GUEST”:can only view live display.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.10 CONTROL SETTING MENU  
CONTROL SETTING MENU  
RS232 BAUD RATE  
RS232 STOP BIT  
RS232 PARITY  
: 9600 BPS  
: 1  
: NONE  
: 8  
RS232 DATA BIT  
: 9600 BPS  
: 1  
: NONE  
: 8  
RS485 BAUD RATE  
RS485 STOP BIT  
RS485 PARITY  
RS485 DATA BIT  
: 1  
RS232/RS485 ID  
In the CONTROL SETTING MENU, we define  
(1) RS232 BAUD RATE: There are 6 different speeds that can be used to transmit instruction or  
information through the RS232 port on the device, 1200 baud,2400 baud,4800 baud,9600 baud,  
19200 baud,and 3840 baud. The default setting from the factory is 9600 baud.  
(2) RS232 STOP BIT: Select stop bit: 1 or 2  
(3) RS232 PARITY: Select parity mode: NONE/ODD/EVEN  
(4) RS232 DATA BIT: Select data bit : 8 or 7  
(5) RS485 BAUD RATE: There are 6 different speeds that can be used to transmit instruction or  
information through the RS485 port on the device, 1200 baud,2400 baud,4800 baud,9600 baud,  
19200 baud,and 3840 baud.  
(6) RS485 STOP BIT: Select stop bit: 1 or 2  
(7) RS485 PARITY:Select parity lever: NONE/ODE/EVEN  
(8) RS485 DATA BIT: Select data bit : 8 or 7  
(9) RS232/RS485 ID: RS232/RS485 address.The adress range for the DVR: 1~200.  
NOTE: Settings for remote keyboards KS-KBK and KS-KBJ:  
RS-485 Baud rate: 9600, 1 Stop bit, Parity NONE, ID (device number) range: 1~32  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.11 BUZZER SETTING MENU  
BUZZER SETTING MENU  
BUZZER  
:
ENABLE  
RECORD-IN  
ALARM-IN  
MOTION-IN  
DISK FULL  
VIDEO LOSS  
TIMER  
:
:
:
ON  
ON  
ON  
ON  
ON  
ON  
:
:
:
In BUZZER SETTING MENU, we define the buzzer  
ON/OFF for following event:  
RECORD-IN, ALARM-IN, MOTION-IN, DISK FULL, VIDEO LOSS AND TIMER  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
MENU  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.12 ARCHIVE SETTING MENU  
ARCHIVE SETTING MENU  
: 720 X 480  
: ON  
: TOP  
: ON  
: TOP  
PICTURE SIZE  
TIME STAMP  
TIME STAMP POS  
WATER MARK  
WATER MARK POS  
In the ARCHIVE SETTING MENU, we define for picture and movie export to CF-card:  
(1) PICTURE SIZE :  
Selects picture size for copying image to CF card:  
Big size:720x480 / 720x576 for NTSC / PAL.  
Small size:352x240 / 352x288 for NTSC / PAL.  
(2) TIME STAMP :  
ON: Shows the time stamp on the picture when copying image to CF card.  
OFF: This erases the time stamp on the picture when copying image to CF card.  
(3) TIME STAMP POS (Position):  
BOTTOM: The time stamp will show on the bottom of the image.  
TOP: The time stamp will show on the top of the image.  
(4) WATER MARK:  
ON: Shows a water mark on the picture when copying image to CF card.  
OFF: No water mark on the picture when copy image to CF card.  
(5) WATER MARK POS (Position):  
BOTTOM: Water mark will show on the bottom of the image.  
TOP: Water mark will show on the top of the image.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.13 MATRIX SETTING MENU  
MONITOR-0 SETTING MENU  
CH DWELL EVENT  
MATRIX SETTING MENU  
00  
00  
00  
00  
00  
00  
00  
00  
00  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
07 SECS NONE  
CALL MONITOR  
ENTER  
MONITOR-1  
MONITOR-2  
MONITOR-3  
MONITOR-4  
(Dialog 1)  
(Dialog 2)  
In the MATRIX SETTING MENU, we define the standard sequences for each matrix monitor  
and event, which override these sequences.  
Users may set up to 5 call monitors accordingly (Dialog 1).  
Note: CALL MONITOR is the regular CALL MONITOR. MONITOR-1~4 are additional 4 call  
monitors for video matrix functions.  
Select the desired call monitor and then press ENTER key. The SUB-MENU will show as Dialog 2.  
CH, DWELL, EVENT:  
(1) CH (Channel): Select the camera to be shown in the standard sequence of this call  
monitor. With setting “00” the channel will be skipped in the sequence.  
(2) DWELL (Dwelling time): Set 0~99 seconds for the dwelling time of each camera.  
(3) EVENT: Set the alarm and correspondent motion to the camera.  
NONE: no alarm or motion action is assigned to this camera.  
MOTION: If MOTION detection is active for this camera, the camera will be  
displayed, if motion is detected. After alarm record duration the monitor switches  
back to standard sequence or spot camera (depending on operation).  
A01 ~ A09: The camera will be displayed, if selected alarm input is active.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
6.14 SYSTEM SETTING MENU  
SYSTEM SETTING MENU  
PLAY WITH AUDIO-1 :  
PLAY WITH AUDIO-2 :  
ON  
ON  
PLAY SPEED  
:
50 IPS  
PASSWORD ENABLE : DISABLE  
PASSWORD:  
DISK USAGE  
SIZE (GB)  
888888  
HDD-1  
160  
HDD-2  
160  
:
RECORD POS  
PLAY POS  
:
* 30.7%  
*30.7%  
NO  
0%  
:
0%  
DISK RENEW:  
NO  
SYSTEM UPDATE:  
LOAD DEFAULT:  
NO  
NO  
In the SYSTEM SETTING MENU, we define  
(1) PLAY WITH AUDIO: AUDIO-1, AUDIO-2  
ON/OFF: Play back with or without audio.  
(2) PLAY SPEED: Set the playback speed. Maximum 60 (NTSC) / 50 (PAL).  
(3) PASSWORD ENABLE: Enable/Disable the password protection.  
(4) PASSWORD: Set password with 6 digits  
(5) DISK USAGE: HDD-1, HDD-2  
SIZE: Applied HDD size.  
RECORD POS: HDD usage rate, record position, “*” shows the active HDD  
PLAY POS: current playback position, “*” shows the active HDD  
DISK RENEW: Erase HDD-1, HDD-2  
(6) SYSTEM UPDATE: Select YES/NO for updating system.  
YES: Download the update S/W into C.F card through your PC and insert the CF card  
into the slot on the front panel of DVR. Press ENTER key to start.  
Notice: After the system is successfully updated, please reboot the system.  
(7) LOAD DEFAULT: Select YES/NO to load factory default setting, neccessary after update.  
Turn the JOG dial clockwise or counter-clockwise to select the options.  
Press ENTER key to confirm the option and move to next column.  
ENTER  
Press MENU key to return to Main Menu, press again to leave Set up Menu.  
MENU  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
7.1 INSTANT RECORDING  
Press REC key to start continuous recording with setting of “NORMAL RECORD”.  
The recording rate and recording quality are set in the RECORD SETTING MENU.  
The LCD screen on the front panel of DVR will display as follows:  
REC  
2003/11/23  
21:56:47  
REC  
HDD1  
21:56:52  
70%  
50 IPS  
Display shows operation status, active HDD, record position on active HDD,  
record frame rate ant current time.  
REC, Maximum 60 (NTSC) / 50 (PAL) fields will also show on the main  
monitor display if you press the DISPLAY key to show camera title and  
date/time.  
Press STOP key to stop recording.  
Since the DVR had Duplex feature, STOP key can be activated both in Playing back and  
Recording. In Duplex mode first STOP will stop playback, second STOP will stop recording.  
STOP  
When the HDD is full, the machine will or
from the beginning of the HDD. It depends on the setting in RECORD SETTING MENU.  
7.2 ALARM RECORDING  
When the ALARM OPERATION setting is “ON”, the DVR will automatically record  
when alarm occurs , and will automatically stops recording at the end of the alarm duration period.  
As example, we set ALARM RECORDING SPEED on 60 (NTSC) / 50 (PAL) field, the screen  
will show as below,  
A.  
REC (50IPS)  
DISK:39GB  
A.  
DIS
Instant recording and timer recording will stop when an alarm occurs.  
Please refer details in RECORD SETTING MENU (page 19).  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing Back  
8.1 NORMAL PLAYBACK  
(1) Playback  
Press the PLAY key to start playing back the stored image/audio  
from the last SEGMENT.  
PLAY  
NOTE: In Duplex mode (simultaneous record and playback) the playback  
speed is limited to 25 IPS. For realtime display of 50 IPS records stop  
recording before starting playback.  
(2) Fast Forward/Reverse Playback  
During playing back, turn the SHUTTLE ring clockwise to start fast forward  
playing back.  
The speed will be shown on the screen at the bottom of the screen.  
>> 2X, 4X, 8X, 16X, 32X, 600X  
Turn the SHUTTLE ring counter-clockwise to start fast reverse playing back.  
The speed will be shown on the screen.  
<< 2X, 4X, 8X, 16X, 32X, 600X  
(3) Slow Forward/Reverse Playback  
During playing back,press PAUSE key to freeze the playing back picture.  
PAUSE  
Turn the SHUTTLE ring clockwise to start slow forward playing back.  
The speed will show at the bottom of the screen.  
>> 1/2, 1/4, 1/8, 1/10, 1/16, 1/32  
Turn the SHUTTLE ring counter-clockwise and slow reverse playback starts.  
The speed will show on the SCREEN at the corner of the screen.  
<< 1/2, 1/4, 1/8, 1/10, 1/16, 1/32  
(4) Field advance Forward/Reverse  
During PAUSE mode, turn the JOG dial clockwise to advance the  
still image field by field.  
Turn the job dial counterclockwise to rewind the still image field by  
field.  
(5) Press STOP key to stop playing back.  
Notice: Press STOP key again will stop recording. Please check the REC key if it  
lights or not after your operation.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Search Playback  
8.2 SEARCH PLAYBACK  
(1) Segment List search playback  
Press SEARCH key to enter the SEARCH MENU dialog.  
SEARCH  
SEARCH MENU  
BY SEGMENT LIST  
BY ALARM LIST  
BY DATA TIME  
Turn the JOG dial to select BY SEGMENT LIST and press  
ENTER key.  
A segment is a range on the HDD, beginning with record start  
(manual, alarm, motion or after power loss) and ending with  
record stop.  
NOTE: If the recorder starts to overwrite a HDD, also a new  
segment will be generated.  
The submenu will display as follows:  
SEGMENT SEARCH  
2003/04/24 19/03/29 HDD1  
2003/04/25 12/30/30 HDD1  
2003/05/20 12/00/00 HDD2  
0001  
0002  
0003  
Turn the JOG dial to select desired items.  
Press ENTER key to start playing back selected segment.  
ENTER  
STOP  
Press STOP key to end playing back and return to static display.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Search Playback  
(2) Alarm List search playback  
Press SEARCH key to enter the SEARCH MENU dialog.  
SEARCH  
SEARCH MENU  
BY SEGMENT LIST  
BY ALARM LIST  
BY DATA TIME  
Turn the JOG dial to select BY ALARM LIST and press ENTER  
key. The submenu will display as follows:  
ALARM SEARCH  
M01 2003/04/24 19:03:29 HDD 1  
A03 2003/04/25 12:30:30 HDD1  
M03 2003/05/20 12:00:00 HDD2  
00001  
00002  
00003  
A01 : Alarm recording by Alarm-in 1.  
M03: Motion recording by camera 3.  
T : Timer recording.  
PL: automatic record restart after end of power loss  
: to next page  
: to previous page.  
Press ENTER key to start playing back selected alarm list.  
ENTER  
STOP  
Press STOP key to end playing back and return to static display.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Search Playback  
(3) Date/Time Search Playback  
Press SEARCH key to enter the SEARCH MENU dialog.  
SEARCH  
SEARCH MENU  
BY SEGMENT LIST  
BY ALARM LIST  
BY DATA TIME  
Turn the JOG dial to select BY DATA TIME and press ENTER  
key. The submenu and instruction will display as follows:  
DATE/TIME SEARCH  
YEAR/MM/DD HH:MM:SS HDD  
2003 /01 /01 21: 33: 26  
1
PRESS SEARCH TO START SEARCH  
PRESS MENU TO EXIT  
Turn the JOG dial to select desired date/time and stored hard disk.  
Press SEARCH key to start playing back by date/time search or  
press MENU key to exit..  
SEARCH  
Notice: If there is no image stored in the date/time specified then the machine  
will start playing back from the nearest set time automatically.  
Press STOP key to end playing back and return to static display.  
STOP  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DATA EXPORT  
9. DATA EXPORT  
Insert a Compact Flash card into the Compact Flash slot on the front panel of DVR.  
When inserting the Compact Flash card, make sure that insert direction is correct.  
NOTE: COPY function is not possible during RECORD. Stop recording to enable COPY  
function!  
9.1 STILL IMAGE COPY  
The still image copy function is possible in all playback view modes.  
Press the PLAY key to start playing back.  
Press the PAUSE key to pause playback.  
The Monitor OSD shows “PAUSE ON (1~9 for EDSR-900, 1~16 for  
EDSR-1600)” . The displayed number shows the active channel for the  
COPY function.  
PAUSE  
Turn the JOG Dial clockwise to choose your desired image.  
While displayed as your desired image of choice ,  
press the COPY key. The “ Copying …” will be shown on the screen during  
the process.  
COPY  
Notice:  
Copied images are stored as a single picture. Copied files are saved as .JPG file.  
Notice:  
Please wait after the message “DONE” about 5 seconds before removing CF-card  
for ensure correct finish of write process.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DATA EXPORT  
9.2 COPY TO MOVIE FILE  
NOTE: COPY function is not possible during RECORD.  
Stop recording to enable COPY function!  
Press the PLAY key to start playing back.  
PLAY  
Press COPY key and then the copy menu and instruction appears.  
The main monitor switches to full screen display with following OSD:  
COPY  
CH01  
COPY TO MOVIE FILE  
USE JOG TO SELECT PICTURE  
PRESS COPY TO START COPY  
PRESS PAUSE TO PAUSE COPY  
PRESS STOP TO CLOSE FILE  
PRESS MENU TO EXIT  
2003/11/01  
00:08:08  
Turn the JOG Dial clockwise to choose your channel for copying.  
While displaying as your desired image of choice,  
Press COPY key to start copying image.  
COPY  
Press PAUSE key to pause copy image.  
PAUSE  
Press STOP key to finish copy and close file.  
STOP  
MENU  
Press MENU key to return to playback. Press STOP to stop playing back.  
Notice: Please wait after the message “DONE” about 5 seconds before removing CF-  
card for ensure correct finish of write process.  
Notice: Copied images are stored as a movie picture. Copied files are saved as .MOV file.  
Use QuickTime to play the retrieved .MOV files. You may download QuickTime at  
. The playback version for QuickTime is free.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DATA EXPORT  
9.3 EXPORT EVENT LOG LIST  
This function allows to export the event log list to CompactFlash – Card.  
The generated text file in in *.txt format.  
Press „DISPLAY“ key and hold key for about 2 seconds.  
DISPLAY  
EVENT LOG  
TYPE  
MOTION  
VL  
ID  
2
TIME  
2004/01/02 12:12:54  
2004/01/02 12:12:54  
2003/12/29 12:12:54  
2003/12/28 12:12:54  
1
VL  
3
1
VL  
USE JOG TO SWITCH PAGE  
HIT CALL TO TURN OFF BUZZER  
HIT COPY TO SAVE EVENT TO CF CARD  
HIT MENU TO EXIT  
The event log list will be displayed:  
TYPE: event type:  
MOTION : motion detection  
ALARM: alarm in  
VL:  
PL:  
video loss  
restart after Power Loss  
ID:  
video input number for motion and video loss, alarm in contact for Alarm  
TIME: start time of event  
Turn the JOG Dial to jump to next event list page.  
Press CALL to switch off buzzer, if active.  
CALL  
COPY  
MENU  
Press COPY to save the current event list page to CompactFlash Card.  
Press MENU to exit event log list.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MONITOR VIEWS / OPERATION  
10. MONITOR VIEWS / OPERATION  
The EDSR900/1600 digital recorders provide 1 main monitor and 5 matrix monitors.  
These monitors have different functionalities:  
Main monitor:  
- Full screen and multi screen display:  
EDSR-900: Full, 4, 6, 7, 8, 9, PIP, and 2x zoom  
EDSR-1600: Full, 4, 6, 7, 9, 10, 13, 16, PIP, sequence and 2x zoom  
- Live- and Playback display  
- OSD for camera title, status messages, setup menu  
- full screen display  
CALL / Matrix monitors:  
- sequence mode or fixed camera display  
- display of motion or alarm cameras  
- OSD for camera title and alarm messages  
10.1. MAIN MONITOR  
The MODE key switches the different multiscreen modes.  
MODE  
The numeric keys switch to full screen mode with the selected camera.  
DISPLAY switches the OSD for camera titles and status messages ON/OFF.  
DISPLAY  
ZOOM  
The ZOOM function is only available in full screen mode. Press ZOOM to  
activate the electronix 2 x zoom. Use the JOG wheel to move left/right in the  
picture. ENTER switches vertical / horizontal movement.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MONITOR VIEWS / OPERATION  
10.2. CALL / MATRIX MONITORS  
Press CALL to change settings for CALL / MATRIX monitors.  
The Main monitor shows following dialogue:  
CALL  
MATRIX NORMAL STATE  
SETTING MENU  
PRESS CALL TO SET CALL  
MONITOR  
PRESS 1-4 TO SELECT MATRIX  
PRESS MENU TO EXIT  
Select the monitor by pressing CALL or the numeric keys 1~4.  
The Main monitor shows following dialogue (example with monitor 1):  
SETTING MATRIX 1  
SEQUENCE  
OSD  
ON  
PRESS 1 – 16 TO SELECT SPOT CAMERA  
PRESS SEQUENCE TO SEQUENCE  
PRESS DISPLAY TO TURN OSD ON/OFF  
PRESS MENU TO EXIT  
The current status of the selected monitor is shown in the second and third column  
(Sequence / Spot, OSD ON/OFF).  
Press sequence to activate the standard sequence for this monitor (setup for this  
sequence in menu MATRIX, page 24)  
SEQUENCE  
The numeric keys switch to full screen mode with the selected camera.  
Press MENU to jump back to monitor selection menu.  
MENU  
NOTE:  
In menu MATRIX defined events for motion and alarm have  
higher priority and will override the manual settings. After end of  
any event the monitor switches back to the manual settings.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. REMOTE CONTROL  
11.1 RS-485 REMOTE CONTROL  
The new standard EverFocus EDSR remote protocol allows challenging installations with DVR remote  
control at different installation sites.  
EDSR remote control is supported by the keyboards KS-KBJ (with 3-axis joystick and 2 additional  
RS-485 – Ports for telemetry control with independent telemetry protocols) and KS-KBK (no  
telemetry).  
Up to 32 units are allowed in the RS-485 bus. The RS-485 bus requires serial wiring with 2-wire  
shielded twisted pair cable(“daisy chain”). Maximum cable lenght of the bus is 1200 m.  
Star wiring is only possible with additional RS-485 distributor.  
Mixed installation is possible with following recorder types:  
EDSR100H, EDSR100M, EDSR400, EDSR400H, EDSR400M, EDSR900, EDSR1600  
For installation details please consult the manuals of KS-KBK and KS-KBJ keyboard.  
Installation example (2 remote operators, 1 EDSR900, 1 EDSR1600) :  
DVR1: EDSR1600  
MAIN1 M1-1 M1-2  
M1-3  
M1-4  
Video 1 x  
Video 5 x  
RS-485 2 wire  
DVR2: EDSR900  
Video 5 x  
Video 1 x  
MAIN2 M2-1 M2-2  
M2-3  
M2-4  
CALL 1 CALL 2  
RS-485 2 wire  
RS-485 2 wire  
Operator 2:  
Operator 1:  
1x Multi screen view DVR1 (MAIN)  
4x Full screen view DVR1 (MATRIX)  
1x Multi screen view DVR1 (MAIN)  
4x Full screen view DVR2 (MATRIX)  
1x Full screen view DVR1  
1x Full screen view DVR2  
RJ45 (RS485) pin assignment  
There are two RJ-45 (RS-485) connectors on the back panel of the DVR (loop through). Please  
refer the following pin assignment for application.  
PIN  
FUNCTION  
1
2
3 4  
5
6
7
8
1
2
3
4
5
6
7
8
GND  
NC  
RX +  
NC  
NC  
RX -  
NC  
NC  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IR Remote Controller  
11.2 IR Remote Controller (optional)  
The remote controller (RC-200, Figure 1) is an accessory to enhance the handy operations of the  
DVR. You can perform all the settings and operations by the remote controller. The effective  
distance is up to 10 meters without any obstacle. The keypad functions are same as the front  
panel key button of the DVR.  
There are some replacement keys for JOG and SHUTTLE, definitions are:  
JOG  
JOG  
: Same as turning the JOG clockwise.  
: Same as turning the JOG counter-clockwise.  
SHUTTLE  
1: fast forward 2X or slow forward 1/2X.  
2: fast forward 4X or slow forward 1/4X.  
3: fast forward 8X or slow forward 1/8X.  
4: fast forward 16X or slow forward 1/10X.  
5: fast forward 32X or slow forward 1/16X.  
6: fast forward 600X or slow forward 1/32X.  
SHUTTLE  
1: fast rewind 2X or slow rewind 1/2X.  
2: fast rewind 4X or slow rewind 1/4X.  
3: fast rewind 8X or slow rewind 1/8X.  
4: fast rewind 16X or slow rewind 1/10X.  
5: fast rewind 32X or slow rewind 1/16X.  
6: fast rewind 600X or slow rewind 1/32X.  
Note: The channel keys #10~16 are only active  
with EDSR-1600 recorder  
Figure 1  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
View From Internet/Intranet  
12. View From Internet/Intranet  
Basic Operations and Login Display:  
Go to the Internet Explorer, key in the network IP address, for example,  
(must be the same IP address as the one assigned to the  
unit from the Network Setting Menu. You need a FIXED IP Address, please contact your ISP for the IP)  
The LOGIN dialog will show on the screen.  
User’ must enter the correct user-name and password defined in the Network Setting menu.  
For example:  
Enter ADMIN for user name and ADMIN for password and then Click On “submit” to enter to system.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
View From Internet/Intranet  
Main Screen  
10  
11  
19  
12  
13  
14  
1
2
3
4 5  
6
7
8
9
15 16 17 18  
Above diagram is the main screen display.  
The icons on the lower corner of the screen are mainly for control and Configuration, those on  
the right corner are for status indication.  
If any icon is grayed, it means that the specific function is not accessible in the current mode.  
The followings are a brief description for each of the icons.  
1.  
2.  
REV. PLAY : Reverse Video Playback.  
STOP : Press this key to stop Video Playback.  
3.  
PLAY: Play back the Video display.  
4.  
5.  
STEP FORWARD the Video Playback display.  
PAUSE: To pause the Video Playback display.  
6.  
7.  
STEP BACKWARD the Video Playback display  
CONTROL MODE: To switch to direct remote control mode.  
Note: Only allows user with access level “ADMIN”..  
C
8. Control for Playback Video Speed  
9. Control for Playback Position  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
View From Internet/Intranet  
10. The system allows up to 3 ways playback video, by SEGMENT, ALARM LIST and DATE TIME.  
(Playback by SEGMENT LIST, click Refresh to show list)  
(Playback by ALARM LIST, click Refresh to show list)  
(Playback by Date time)  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
View From Internet/Intranet  
11. All available segments are shown in the list. Click to select and highlight.  
12. Click to playback selected video segment.  
13. Press this icon to show the segment or list.  
14. Current connection and playback status is shown along with date and time.  
15. Full screen view.  
16. Quad screen view.  
17. Nine split screen view.  
18. Sixteen split screen view (only for 16 CH DVR).  
19. A pop-up menu to select camera to view will be shown by pressing right mouse button.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix-A  
LAN Functional Specification  
Specifications:  
Network Interface:  
LAN controller Chip:  
LAN Connector:  
Protocol:  
10Mbits/s Ethernet (10Base T)  
RealTek 8019  
RJ-45  
HTTP,TCP/IP.ICMP,ARP  
Standard browser such as internet  
Explorer / Netscape with JAVA support  
JPEG  
80, 1111, 2222, 3333, 4444, 6666  
4
Remote Access:  
Image Compression:  
Used Ports:  
Max. user number:  
Frame rate:  
max. 1,5 IPS depending on network conditions  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix-B  
Time Lapse Mode Recording Time Table  
: 15 kB  
: 19 kB  
: 23 kB  
: 27 kB  
: 31 kB  
: 35 kB  
Lower  
Low  
Basic  
Standard  
High  
? When Recording with 160GB HDD  
(Estimated with typical image-low noise level)  
Superior  
Unit: Hour  
NTSC  
system storage(GB):  
PICTURE QUALITY (KB)  
160  
Recording  
Speed  
(fps)  
60  
LOWER  
15  
LOW  
19  
BASIC  
23  
STANDARD  
27  
HIGH  
31  
SUPERIOR  
35  
21.2  
49.4  
39  
32.2  
27.4  
23.9  
30  
98.8  
78  
64.4  
54.9  
47.8  
42.3  
20  
148.1  
197.5  
296.3  
592.6  
2963  
117  
96.6  
82.3  
71.7  
63.5  
15  
155.9  
233.9  
467.8  
2339.2  
4678.4  
7797.3  
11695.9  
128.8  
193.2  
386.5  
1932.4  
3864.7  
6441.2  
9661.8  
109.7  
164.6  
329.2  
1646.1  
3292.2  
5487  
95.6  
84.7  
10  
143.4  
286.7  
1433.7  
2867.4  
4779  
7168.5  
127  
5
1
254  
1269.8  
2539.7  
4232.8  
6349.2  
0.5  
0.3  
0.2  
5925.9  
9876.5  
14814.8  
8230.5  
Unit: Hour  
PAL  
Recording  
PICTURE QUALITY (KB)  
Speed  
(fps)  
50  
LOWER  
15  
LOW  
19  
BASIC  
23  
STANDARD  
27  
HIGH  
31  
SUPERIOR  
35  
59.3  
46.8  
38.6  
32.9  
28.7  
25.4  
25  
118.5  
296.3  
592.6  
1481.5  
2963  
93.6  
77.3  
65.8  
57.3  
50.8  
10  
5
233.9  
467.8  
1169.6  
2339.2  
4678.4  
5848  
193.2  
386.5  
966.2  
1932.4  
3864.7  
4830.9  
9661.8  
19323.7  
164.6  
329.2  
143.4  
286.7  
716.8  
1433.7  
2867.4  
3584.2  
7168.5  
14336.9  
127  
254  
2
823  
634.9  
1269.8  
2539.7  
3174.6  
6349.2  
12698.4  
1
1646.1  
3292.2  
4115.2  
8230.5  
16460.9  
0.5  
0.4  
0.2  
0.1  
5925.9  
7407.4  
14814.8  
29629.6  
11695.9  
23391.8  
Reference:24H=1 day.168H=1 week, 720H=1 month,8760H=1 year  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix-B  
? When Recording with 320GB HDD  
: 15 kB  
: 19 kB  
: 23 kB  
: 27 kB  
: 31 kB  
: 35 kB  
Lower  
Low  
Basic  
Standard  
High  
Superior  
(Estimated with typical image-low noise level)  
Unit: Hour  
NTSC  
system storage(GB):  
PICTURE QUALITY (KB)  
320  
Recording  
Speed  
(fps)  
60  
LOWER  
15  
98.8  
LOW  
19  
78  
BASIC  
23  
64.4  
STANDARD  
27  
HIGH  
31  
47.8  
SUPERIOR  
35  
54.9  
42.3  
30  
197.5  
155.9  
233.9  
311.9  
467.8  
935.7  
4678.4  
9356.7  
15594.5  
23391.8  
128.8  
193.2  
257.6  
386.5  
772.9  
3864.7  
7729.5  
12882.4  
19323.7  
109.7  
95.6  
84.7  
20  
15  
296.3  
395.1  
164.6  
219.5  
143.4  
191.2  
286.7  
573.5  
2867.4  
5734.8  
9557.9  
14336.9  
127  
169.3  
254  
10  
592.6  
329.2  
5
1
1185.2  
5925.9  
11851.9  
19753.1  
29629.6  
658.4  
507.9  
2539.7  
5079.4  
8465.6  
12698.4  
3292.2  
6584.4  
10973.9  
16460.9  
0.5  
0.3  
0.2  
Unit: Hour  
PAL  
Recording  
PICTURE QUALITY (KB)  
Speed  
(fps)  
50  
LOWER  
15  
LOW  
19  
BASIC  
23  
STANDARD  
27  
HIGH  
31  
SUPERIOR  
35  
118.5  
93.6  
77.3  
65.8  
57.3  
50.8  
25  
237  
187.1  
154.6  
131.7  
114.7  
101.6  
10  
592.6  
467.8  
386.5  
329.2  
286.7  
254  
5
1185.2  
2963  
935.7  
772.9  
658.4  
573.5  
507.9  
2
2339.2  
4678.4  
9356.7  
11695.9  
23391.8  
46783.6  
1932.4  
3864.7  
7729.5  
9661.8  
19323.7  
38647.3  
1646.1  
3292.2  
6584.4  
8230.5  
16460.9  
32921.8  
1433.7  
2867.4  
5734.8  
7168.5  
14336.9  
28673.8  
1269.8  
2539.7  
5079.4  
6349.2  
12698.4  
25396.8  
1
5925.9  
11851.9  
14814.8  
29629.6  
59259.3  
0.5  
0.4  
0.2  
0.1  
Reference:24H=1 day.168H=1 week, 720H=1 month,8760H=1 year  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendic C: Serial Interface Specifications  
Serial Interface Specifications  
1. RS-232 pin assignment  
The DVR may be controlled by a computer or a terminal via the standard  
D-SUB 9-pin RS-232 connector.  
The pin assignment of the D-SUB 9-pin connector  
1 2 3 4 5  
6 7 8  
9
HOST  
PIN # NAME  
DVR  
PIN # NAME  
1
2
3
4
5
6
7
8
9
NOT CONNECTED  
1
2
3
4
5
6
7
8
9
NOT CONNECTED  
RXD  
TXD  
RXD  
TXD  
NOT CONNECTED  
GROUND  
NOT CONNECTED  
GROUND  
NOT CONNECTED  
NOT CONNECTED  
NOT CONNECTED  
NOT CONNECTED  
NOT CONNECTED  
NOT CONNECTED  
NOT CONNECTED  
NOT CONNECTED  
2. Transmission setting  
There are 6 different speeds that can be used to transmit instruction or information through  
the RS232/RS485 port on the device, 1200 baud, 2400 baud, 4800 baud, 9600 baud,  
19200 baud and 3840 baud.  
The default setting from the factory is 9600 baud.  
Please refer to Chart 6.10 (Page21) for details.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendic C: Serial Interface Specifications  
3. Remote Control Protocol  
A computer or a terminal can be used to control the unit by sending the packet as following.  
1-1. Sample control code packets  
Example1 : A packet that send "REC" key to DVR (ID=5)  
0x85  
0x00  
0x05  
0x4B  
0x08  
0x5D  
(length)  
(Receiver ID high byte)  
(Receiver ID low byte)  
(OPcode = key )  
(DATA1 = "Rec" keycode )  
(checksum)  
Example2 : A packet that send "PAUSE" key to DVR (ID=4999)  
0x85  
0x27  
0x07  
0x4B  
0x0C  
0x0A  
(length)  
(Receiver ID high byte)  
(Receiver ID low byte)  
(OPcode = key )  
(DATA1 = "Pause" keycode )  
(checksum)  
Example3 : A packet that send "PLAY" key to all DVR (broadcast)  
0x85  
0x7f  
(length)  
(Receiver ID high byte)  
(Receiver ID low byte)  
(OPcode = key )  
(DATA1 = "Play" keycode )  
(checksum)  
0x7f  
0x4B  
0x0B  
0x59  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendic C: Serial Interface Specifications  
2-1. The format of message packet is as follows:  
Length Byte (Prefix: 0x86, 0x87, or 0x88 ..... )  
Receiver ID high byte  
Receiver ID low byte  
Opcode Byte  
Data Byte1  
Data Byte2  
Data Byte3  
Checksum Byte  
2-2. Length Byte  
This Length Byte is also a prefix. Bit7 must be 1.  
EX:  
0x87 ==> this packets has 7 bytes length. ( not included Length byte itself )  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendic C: Serial Interface Specifications  
2-3. Receiver ID  
2-3. Receiver ID  
1). Individual receiver ID  
Decimal  
0
14bit binary value  
Hbyte  
00  
Lbyte  
00  
Receiver ID (EDSR)  
ID = 0  
0000000 0000000  
0000000 0000001  
0000000 0000010  
1
00  
01  
ID = 1  
2
00  
02  
ID = 2  
....  
126  
127  
128  
129  
255  
256  
....  
0000000 1111110  
0000000 1111111  
0000001 0000000  
0000001 0000001  
0000001 1111111  
0000010 0000000  
00  
00  
01  
01  
01  
02  
7e  
7f  
ID = 126  
ID = 127  
ID = 128  
ID = 129  
ID = 255  
ID = 256  
00  
01  
7f  
00  
511  
....  
0000011 1111111  
1111111 1111110  
03  
7f  
7f  
ID = 511  
16382  
7e  
ID = 16382  
2). Broadcast ID  
Decimal  
16383  
14bit binary value  
1111111 1111111  
Hbyte  
7f  
Lbyte  
7f  
Receiver ID  
all EDSR  
connect to RS485/RS232  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendic C: Serial Interface Specifications  
2-4. Opcode Byte & Data bytes  
2-4-1. OPcode  
OPcode  
0x4B  
Data1  
Function  
Keycode  
command  
A remote key pressed  
Matrix command  
0x4D  
2-4-2. Remote keys (OPcode=0x4B)  
----------------------------------------------------------------------------------------------------  
Data1 Key Data1 Key  
0x1e JOG<  
0x1f JOG>  
0x20 CH5  
0x00 CH1  
0x01 CH2  
0x02 CH3  
0x21 CH6  
0x03 CH4  
0x22 CH7  
0x04 MODE  
0x23 CH8  
0x05 ZOOM  
0x24 CH9  
0x06 SEQ  
0x25 CH10  
0x26 CH11  
0x27 CH12  
0x28 CH13  
0x29 CH14  
0x2a CH15  
0x2b CH16  
0x2c SELECT  
0x2d CALL  
0x2e ENTER  
0x2f (reserve)  
0x30 (reserve)  
0x31 (reserve)  
0x32 (reserve)  
0x33 (reserve)  
0x34 (reserve)  
0x07 MENU  
0x08 REC  
0x09 REV.PLAY  
0x0A STOP  
0x0B PLAY  
0x0C PAUSE  
0x0D SEARCH  
0x0E COPY  
0x0F DISPALY  
0x10 SHUTTLE<<x1  
0x11 SHUTTLE<<x2  
0x12 SHUTTLE<<x4  
0x13 SHUTTLE<<x8  
0x14 SHUTTLE<<x16  
0x15 SHUTTLE<<x32  
0x16 SHUTTLE<<x600  
0x17 SHUTTLE>>x1  
0x18 SHUTTLE>>x2  
0x19 SHUTTLE>>x4  
0x1a SHUTTLE>>x8  
0x1b SHUTTLE>>x16  
0x1c SHUTTLE>>x32  
0x1d SHUTTLE>>x600  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendic C: Serial Interface Specifications  
2-4-3. Matrix command  
(OPcode=0x4D)  
Data1  
Matrix function  
Data1  
Matrix function  
Data1  
Matrix function  
0x42 Matrix monitor4 - ch03 spot  
0x43 Matrix monitor4 - ch04 spot  
0x44 Matrix monitor4 - ch05 spot  
0x45 Matrix monitor4 - ch06 spot  
0x46 Matrix monitor4 - ch07 spot  
0x47 Matrix monitor4 - ch08 spot  
0x48 Matrix monitor4 - ch09 spot  
0x49 Matrix monitor4 - ch10 spot  
0x4a Matrix monitor4 - ch11 spot  
0x4b Matrix monitor4 - ch12 spot  
0x4c Matrix monitor4 - ch13 spot  
0x4d Matrix monitor4 - ch14 spot  
0x4e Matrix monitor4 - ch15 spot  
0x4f Matrix monitor4 - ch16 spot  
0x50 Matrix monitor0 - sequence  
0x51 Matrix monitor1 - sequence  
0x52 Matrix monitor2 - sequence  
0x53 Matrix monitor3 - sequence  
0x54 Matrix monitor4 - sequence  
0x60 Matrix monitor0 - turn OSD on  
0x61 Matrix monitor1 - turn OSD on  
0x62 Matrix monitor2 - turn OSD on  
0x63 Matrix monitor3 - turn OSD on  
0x64 Matrix monitor4 - turn OSD on  
0x70 Matrix monitor0 - turn OSD off  
0x71 Matrix monitor1 - turn OSD off  
0x72 Matrix monitor2 - turn OSD off  
0x73 Matrix monitor3 - turn OSD off  
0x74 Matrix monitor4 – turn OSD off  
0x21 Matrix monitor2 - ch02 spot  
0x22 Matrix monitor2 - ch03 spot  
0x23 Matrix monitor2 - ch04 spot  
0x24 Matrix monitor2 - ch05 spot  
0x25 Matrix monitor2 - ch06 spot  
0x26 Matrix monitor2 - ch07 spot  
0x27 Matrix monitor2 - ch08 spot  
0x28 Matrix monitor2 - ch09 spot  
0x29 Matrix monitor2 - ch10 spot  
0x2a Matrix monitor2 - ch11 spot  
0x2b Matrix monitor2 - ch12 spot  
0x2c Matrix monitor2 - ch13 spot  
0x2d Matrix monitor2 - ch14 spot  
0x2e Matrix monitor2 - ch15 spot  
0x2f Matrix monitor2 - ch16 spot  
0x30 Matrix monitor3 - ch01 spot  
0x31 Matrix monitor3 - ch02 spot  
0x32 Matrix monitor3 - ch03 spot  
0x33 Matrix monitor3 - ch04 spot  
0x34 Matrix monitor3 - ch05 spot  
0x35 Matrix monitor3 - ch06 spot  
0x36 Matrix monitor3 - ch07 spot  
0x37 Matrix monitor3 - ch08 spot  
0x38 Matrix monitor3 - ch09 spot  
0x39 Matrix monitor3 - ch10 spot  
0x3a Matrix monitor3 - ch11 spot  
0x3b Matrix monitor3 - ch12 spot  
0x3c Matrix monitor3 - ch13 spot  
0x3d Matrix monitor3 - ch14 spot  
0x3e Matrix monitor3 - ch15 spot  
0x3f Matrix monitor3 - ch16 spot  
0x40 Matrix monitor4 - ch01 spot  
0x41 Matrix monitor4 - ch02 spot  
0x00 Matrix monitor0 - ch01 spot  
0x01 Matrix monitor0 - ch02 spot  
0x02 Matrix monitor0 - ch03 spot  
0x03 Matrix monitor0 - ch04 spot  
0x04 Matrix monitor0 - ch05 spot  
0x05 Matrix monitor0 - ch06 spot  
0x06 Matrix monitor0 - ch07 spot  
0x07 Matrix monitor0 - ch08 spot  
0x08 Matrix monitor0 - ch09 spot  
0x09 Matrix monitor0 - ch10 spot  
0x0a Matrix monitor0 - ch11 spot  
0x0b Matrix monitor0 - ch12 spot  
0x0c Matrix monitor0 - ch13 spot  
0x0d Matrix monitor0 - ch14 spot  
0x0e Matrix monitor0 - ch15 spot  
0x0f Matrix monitor0 - ch16 spot  
0x10 Matrix monitor1 - ch01 spot  
0x11 Matrix monitor1 - ch02 spot  
0x12 Matrix monitor1 - ch03 spot  
0x13 Matrix monitor1 - ch04 spot  
0x14 Matrix monitor1 - ch05 spot  
0x15 Matrix monitor1 - ch06 spot  
0x16 Matrix monitor1 - ch07 spot  
0x17 Matrix monitor1 - ch08 spot  
0x18 Matrix monitor1 - ch09 spot  
0x19 Matrix monitor1 - ch10 spot  
0x1a Matrix monitor1 - ch11 spot  
0x1b Matrix monitor1 - ch12 spot  
0x1c Matrix monitor1 - ch13 spot  
0x1d Matrix monitor1 - ch14 spot  
0x1e Matrix monitor1 - ch15 spot  
0x1f Matrix monitor1 - ch16 spoz  
0x20 Matrix monitor2 - ch01 spot  
2-5. Checksum Byte  
Checksum is computed as the sum of all previous butye (includeing the length byte), then mask with 0x7f.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix-D  
Alarm I/O pin assignment  
The alarm connector, Figure 1, is used to provide one sensor alarm input for each camera input.  
For easy operation, an alarm extension board, Figure 2, is provided to connect to the alarm connector.  
Each alarm input requires two wires, one wire connects to the desired alarm input pin, the second wire  
connects to the ground.The alarm signal assignment is shown at the following.  
1
13  
1
2
3
4
5
6
7
8
9
10 11 12 13 14  
2
25  
<Figure 1>  
28 27 26 25 24 23 22 21 20 19 18 17 16 15  
PR16D00400  
D-SUB 25 pin female connector (DVR)  
<Figure 2>  
PR16D00400 Alarm extension board  
DVR  
PIN #  
1
NAME / Function  
GND  
Ground  
HOST  
2
ALM 1  
ALM 2  
ALM 3  
ALM 4  
ALM 5  
ALM 6  
ALM 7  
ALM 8  
ALM 9  
Alarm In 1  
Alarm In 2  
Alarm In 3  
Alarm In 4  
Alarm In 5  
Alarm In 6  
Alarm In 7  
Alarm In 8  
Alarm In 9  
PIN #  
1
NAME  
3
GND  
4
2
ALM 1  
5
3
ALM 2  
4
ALM 3  
6
5
ALM 4  
7
6
ALM 5  
8
7
ALM 6  
9
8
GND  
9
ALM 7  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
ALM 8  
ALM 10* Alarm In 10  
ALM 11* Alarm In 11  
ALM 12* Alarm In 12  
ALM 13* Alarm In 13  
ALM 14* Alarm In 14  
ALM 15* Alarm In 15  
ALM 16* Alarm In 16  
ALMRST Alarm Reset  
ALM 9  
ALM 10*  
ALM 11*  
ALM 12*  
ALM 13*  
ALM 14*  
ALM 15*  
ALM 16*  
ALMRST  
REC-IN  
GND  
REC  
Record In  
Reserved  
GIN10  
SPARE-IN  
DISKFULL  
SPARE-OUT  
ALM-N.C  
ALM-N.O  
ALM-COM  
GND  
DISKFULL Disk Full Out  
GO1 Reserved  
ALM-N.C Alarm Out N.C.  
ALM-N.O Alarm Out N.C.  
ALM-COM Alarm OUT COM  
* ALM10~ALM16 are active only for EDSR-1600  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EverFocus Electronics Corp.  
Head Office:  
European Office:  
12F, No.79 Sec. 1 Shin-Tai Wu Road,  
Hsi-Chi, Taipei, Taiwan  
Albert-Einstein-Strasse 1  
D-46446 Emmerich, German  
TEL  
FAX  
: +886-2-26982334  
: +886-2-26982380  
Beijing Office:  
Room 609, Technology Trade Building,  
Shandgdi Information Industry Base,  
Haidian District, Beijing,China  
USA Office:  
2445 Huntington Drive, San Marino,  
CA 91108, U.S.A.  
TEL  
FAX  
TEL  
FAX  
: +86-10-62971096  
: +86-10-62971432  
: +1-626-844-8888  
: +1-626-844-8838  
: +1-888-383-6287 or  
+1-888-EV-FOCUS  
Toll free  
Japan Office:  
1809 WBG Marive East 18F,  
2-6 Nakase.Mihama-ku.  
Chiba city 261-7118, Japan  
TEL  
FAX  
: +81-43-212-8188  
: +81-43-297-0081  
®
EverFocus  
P/N: edsr900_1600_ma_en_r1.02  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Dynex TV DVD Combo DX LTDVD19 09 User Manual
Echo Blower PB 755S H User Manual
EVGA Computer Hardware 141 LF E658 User Manual
Festool Sander RO 150 E User Manual
Fitness Quest Home Gym NBP01075 2 User Manual
FujiFilm Digital Camera 16286412 User Manual
GE Monogram Refrigerator ZISB420DM User Manual
GE Power Supply GEK 106465A User Manual
Global Machinery Company Heat Gun HG2000K User Manual
GN Netcom Cordless Telephone ELT 560 User Manual