GE Monogram Ventilation Hood ZXR7510 User Manual

Installation

Instructions

If you have questions, call 800.GE.CARES or visit our website at: www.monogram.com

ZXR758 and ZXR7510

Recirculating Accessories

For Model ZV750, Vent Hood

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Preparation

REQUIRED ACCESSORIES

• Order the required accessory at the same time as the

vent hood and have on site before installation.

• Each kit includes decorative duct cover, air deflector

and charcoal filters.

This book provides step by step instructions to install the

Monogram ZV750 wall mounted hood for recirculating

operation.

• One of the following accessory kits is required for

non-vented wall mounted installations of model ZV750.

Choose the correct kit according to ceiling heights:

ZXR758 – For 8 to 9 ft. ceiling height.

ZXR7510 – For 9 to 10 ft. ceiling height.

PRODUCT DIMENSIONS

The vent hood must be installed 24" min. and 30" max.

above the cooking surface. 25-1/2" is recommended for

best performance and to insure that the duct cover

meets the ceiling. The cooking surface should be at least

36” above the floor. Installation will be easier if the vent

hood is installed before the cooktop and countertop is

installed.

*Height

to Ceiling

8-1/4"

34-5/8"

21-5/8"

* ZXR758

26-1/4" for 8 ft. Ceiling

38-1/4" for 9 ft. Ceiling

ZXR7510

34-1/4" to 50-1/4" for

*25-1/2" Recommended

9 ft. to 10 ft. Ceiling

* The distance between the cooking surface and the bottom of the

hood must be at least 24” and up to 30” The 25-1/2” recommended

installation height, above the standard 36” countertop, will insure

duct cover fit to the ceiling.

36" Min.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Preparation

POWER SUPPLY

DUCT COVER ACCESSORIES

A duct cover accessory is required for recirculating

operation. Use this chart to determine which

accessory is required for your ceiling height.

IMPORTANT

– (Please read carefully)

WARNING:

ZV750SY Installation Heights

Actual

FOR PERSONAL SAFETY, THIS APPLIANCE MUST

BE PROPERLY GROUNDED.

* Possible Hood

Installation Height

Ceiling

Height

Recirculating

Accessory

Remove house fuse or open circuit breaker before

beginning installation.

24-1/2″

7′ 11″

8′ 0″

8′ 1″

8′ 2″

8′ 3″

8′ 4″

8′ 5″

8′ 6″

8′ 7″

8′ 8″

8′ 9″

8′ 10″

8′ 11″

9′ 0″

9′ 1″

9′ 2″

9′ 3″

9′ 4″

9′ 5″

9′ 6″

9′ 7″

9′ 8″

9′ 9″

9′ 10″

9′ 11″

10′ 0″

25-1/2″

Do not use an extension cord or adapter plug with

this appliance. Follow National Electrical Code or

prevailing local codes and ordinances.

25-1/2″ to 26-1/2″

25-1/2″ to 27-1/2″

25-1/2″ to 28-1/2″

25-1/2″ to 29-1/2″

25-1/2″ to 30″

Electrical supply

This vent hood must be supplied with 120V, 60Hz,

and connected to an individual, properly grounded

branch circuit, and protected by a 15 or 20 amp

circuit breaker or time delay fuse.

• Wiring must be 2 wire with ground.

• If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

• Route house wiring as close to the installation

location as possible. Wiring should enter at least 4"

above the bracket on the right side.

• Connect the wiring to the house wiring in

accordance with local codes.

Grounding instructions

The grounding conductor must be connected to

a ground metal, permanent wiring system, or an

equipment-grounding terminal or lead on the hood.

WARNING:

The improper connection

of the equipment-grounding conductor can result

in a risk of electric shock. Check with a qualified

electrician or service representative if you are in

doubt whether the appliance is properly grounded.

* Based on 36″ countertop height.

ZV750SY Duct Cover Dimensions

9-1/4"

Hood and

Accessory

TOOLS AND MATERIALS

REQUIRED ^{(NOT SUPPLIED)}

22-13/16″

34-5/8″

ZXR758C

18-7/8″

• 10 mm Hex wrench/socket

• Safety glasses

• Tape measure

• Knife

ZXR7510C

• Duct tape

• Spirit level

• Gloves to protect against sharp

edges

• 120V 60Hz. 15 or 20 Amp, 2 wire

with ground. Properly grounded

branch circuit.

• Strain relief for junction cover.

• 6" round duct, length to suit

installation.

• Wire cutter/stripper

• Wire nuts

• Electric drill and

appropriate bits

• Phillips and flat blade

screwdrivers

• Hammer

11-7/8"

• Pliers

• Center punch

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Preparation

• Locate and remove 2 screws at the top of the

REMOVE THE PACKAGING

assembly and 2 screws inside the hood behind the

filter guides on the left and right sides. Discard the

shipping board.

The vent hood is shipped secured to a shipping

board with 4 screws.

• Remove the duct cover, parts box and styrofoam

packaging.

• Lift the hood out of the box, using hand grips on

both sides of the shipping board.

Junction

Box

• Remove and properly discard the plastic wrapping.

Knockout

Mounting

Screw

Mounting

Screw

Shipping Board

• Remove junction box cover.

• Remove knockout from junction box.

• Install strain relief onto junction box.

Mounting Screw

Shipping Board

Check Installation Hardware

Locate the hardware accessory box packed with the

hood and check contents.

•

Drill 1/8" Pilot Holes For Mounting Brackets.

5-7/8"

26-14" to

38-1/4" to

ft. Ceiling

3 Stainless

Steel Grease

Filters

38-1/4" to 50-1/4" For

9ft. to 10 ft. Ceiling

Using Optional Accessory

ZX10SY Duct Cover

17-5/16"

•

Drill 1/8" Pilot Holes.

•

Drill 1/8" Pilot Holes.

Align edge 25-1/2" above Cooking Surface.

Wall Mount Template

10 Wood

Screws

10 Metal Wall

2 Mounting Brackets

Fasteners

Check contents of the required accessory,

ZXR758 or ZXR7510.

2 Large

Flat Washers

2 Wood

Screws

Decorative

Duct

Covers

2 Plastic

Wall Fasteners

Air Deflector with

Upper Duct

Connector

Duct Cover Bracket

(not required for

recirculating operation)

2 Phillips Head

Decorative Screws

2 Phillips Head

Decorative Screws

Recirculating

Decorative

Duct Cover

3 Charcoal Filters

2 Side Bars with 4 Machine Screws

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Instructions

1 DETERMINE INSTALLATION

LOCATION

To determine the exact location of the vent hood.

• Locate the template packed with the literature.

– Measure 36" from the floor to the top of the

cooking surface. Add 25-1/2" recommended

space from the cooking surface to the bottom

of hood. Mark that location.

– Use a level to draw a straight pencil line on the

wall.

– Tape the template in position along the penciled

line. CHECK TO BE SURE THE TEMPLATE IS

LEVEL.

2 INSTALL MOUNTING BRACKETS

Whenever possible, the vent hood should be secured to wall

studs.

• With the template taped in place, use a punch to

mark all mounting screw locations.

• Drill 1/8" pilot holes at the 6 punched locations.

• Remove the template.

• Enlarge holes that did not enter studs to 3/8" and

tap anchors for metal wall fasteners into the holes.

– Drive screws into the fasteners to allow anchors to

expand against the wall material. Remove the

screws for final installation.

• Secure the mounting brackets to the wall studs with

wood screws provided.

– For hollow walls, secure the mounting brackets

through the anchors.

– Measure from the peak of the hood to the ceiling

as indicated.

Ceiling

Screws

“B”

Note: Screws “A” and

Screws

“A”

“B” are pre-assembled

onto the brackets. Do

not remove these

screws.

•

Drill 1/8" Pilot Holes For Mounting Brackets.

5-7/8"

26-14" to

38-1/4" to

ft. Ceiling

38-1/4" to 50-1/4" For

9ft. to 10 ft. Ceiling

Using Optional Accessory

ZX10SY Duct Cover

17-5/16"

•

Drill 1/8" Pilot Holes.

•

Drill 1/8" Pilot Holes.

Align edge 25-1/2" above Cooking Surface.

For ZXR758 –

26-1/4" to 38-1/2" for 8 ft. to 9 ft. ceilings.

For ZXR7510 –

38-1/4" to 50-1/4" for 9 ft. to 10 ft. ceilings.

• Use a level to draw a line straight up, from the

centerline on the template to the ceiling.

House Wiring Locations

• The junction box is located on the top of the

hood, at the front right side.

• Route house wiring as close to the installation

location as possible; through the ceiling, soffit or

back wall. Wiring should enter at least 4" above

the bracket on the right side.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Instructions

3 INSTALL THE HOOD

Place the hood on the brackets and slide left to right

to align with rectangular slots at the top.

Screws “B”

To Secure Hood

To Wall

Lower

Mounting Screws

• Align the hood lower mounting holes with pilot

holes in the wall.

• Using two large flat washers (supplied), install wood

screws or wall fastener screws, loosely, into lower

mounting holes. Do not tighten.

• Level the hood by tightening or loosening the

screws “A” located on the bottom mounting

brackets.

Level and

Height

Adjustment

Screws “A”

• Tighten lower mounting screws.

• Tighten screws “B” located at the top of the

mounting bracket against the hood to clamp

the position. Do not overtighten screws.

• Adjust the installation height by tightening or

loosening the screws “A” at the bottom of the

brackets.

5 INSTALL AIR DEFLECTOR

ASSEMBLY

• Place the assembly over the hood outlet.

• Hold the assembly against the ceiling. The penciled

centerline should show through the slot on the

deflector. Mark the two screw holes on the back of

the assembly.

• Remove the

assembly and

drill 1/8" pilot

holes into

4 SIZE DUCT PIECE

• Hold upper air deflector with duct connector

against the ceiling.

• Measure from the

bottom of the support

to top of the hood

as shown. Reduce

this dimension

by 1" to facilitate

installation. The

duct will cover/

overlap the deflector

Duct

Length

Measure

Length

the wall studs.

• Enlarge holes

and the hood outlets.

that did not enter

studs to 3/8" and

tap plastic or metal

anchors into the

holes, flush with

the wall.

• Mount the assembly

onto the hood outlet,

push up against the ceiling

and install the screws provided.

• Use duct tape to seal the connection.

• Cut duct piece to

size and slip onto the

bottom of the duct

connector.

• Use duct tape to

secure duct piece

to connector.

CAUTION:

Do not use sheet metal screws

on the bottom duct flange.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Instructions

6 CONNECT ELECTRICAL

7 INSTALL DUCT COVERS AND

UTILITY BARS

• Verify that power is turned off at the source.

• Separate the duct covers supplied with the hood.

• Discard the upper (inner) section.

WARNING:

If house wiring is not 2-wire

• Insert the ZXR758 or ZXR7510 duct cover (with

vent holes) into the original lower section. Be sure

that the new duct section is inside the shorter

original section.

with a ground wire, a ground must be provided by

the installer. When house wiring is aluminum, be

sure to use U.L. approved anti-oxidant compound

and aluminum-to-copper connectors.

Mounting Screw Holes

• Insert house wiring through strain relief and

tighten.

• Connect white leads to branch circuit white lead.

• Connect black leads to branch circuit black lead.

• Connect green/yellow leads to branch circuit green

lead or bare ground lead.

• Secure all connections with wire nuts on each

electrical connector.

• Push wires into junction box and replace cover.

Be sure wires are not pinched.

• Place the decorative duct covers on top of the hood.

• Insert the lower portion of the duct cover into the

impressions on the top of the hood.

• Extend the inner duct upwards to meet the ceiling

and support frame.

• Secure the duct cover to the frame with the 2 small

Phillips screws provided.

• Install the side utility bars as shown with screws

provided.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Instructions

8 INSTALL FILTERS

9 FINALIZE INSTALLATION

• Remove the protective film covering the control

panel on the front face of the hood, and any other

packaging materials.

Upper Charcoal

Filter Slots

• Refer to the Owner’s Manual for operating

instructions.

Lower Grease

Filter Slots

• There are two slots inside the back and front of the

hood. These slots will hold the charcoal filters and

stainless steel grease filters in place.

Install Charcoal Filters

Upper Charcoal

Filter Slots

Grasp Tab,

Lift and Pull Forward

• Remove protective film on charcoal filters.

• Tip charcoal filters into the upper (top) slots at the

rear of the opening. Grasp the filter tab, lift and

pull forward until it rests in the front slots.

• Install all 3 charcoal filters.

Install Grease Filters

Lower

Filter Slots

• Remove protective film from grease filters.

• Tip the grease filter into the lower slots at the rear

of the opening. Lift the filter and pull the knob

forward until the filter rests on the slots.

• Install all 3 grease filters.

• To remove the filters, grasp the knob, push the

filter toward the rear and tilt downward. Grasp tabs

on charcoal filters, push toward the rear and tilt

downward.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note: While performing installations described in this book,

safety glasses or goggles should be worn.

For Monogram local service in your area, call

1.800.444.1845.

Note: Product improvement is a continuing endeavor at

General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

Pub. No. 49-80046-1

04/07 JR

GE Consumer & Industrial

GE Appliances

General Electric Company

Louisville, KY 40225

Printed in Italy

monogram.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Compaq Network Card NAS B3000 User Manual
Craftsman Air Compressor 91916644 User Manual
Crown Audio Portable Speaker C 8 User Manual
Cub Cadet Lawn Mower 190 670 100 190 678 100 User Manual
Dymo Printer 18949 User Manual
Dynacord Stereo Amplifier DSA 8204 User Manual
Dynex Paper Shredder DX PS06CC User Manual
Elation Professional Landscape Lighting Zoom 575E User Manual
Electro Voice Car Speaker sb121a 110v User Manual
Field Controls Range Oil Venting Systems User Manual