L0542
IMPORTANT!
KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembled Parts
2 Frames
Pad
Seat Back
Seat Bottom
2 Bases
Footrest
2 Seat Bottom Tubes
Food Tray
Hinge Rod
Base Tray
Teether Toy
Note: Tighten or loosen all screws with a Phillips screw-
driver.
Do not over-tighten the screws.
#8 x 1,9 cm Screws – 8
#10 x 2,2 cm Black Screw – 7
Shown Actual Size
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before assembly and each use, inspect this prod-
uct for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Mattel for replacement parts and instructions if needed.
Never substitute parts.
Footrest
Seat Bottom
1
•Place the seat bottom face down on a flat surface.
•At an angle, fit the footrest on the seat bottom, as shown.
3
•Align the holes in the plastic rings and the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each plastic ring and into
the seat bottom tubes, as shown. Tighten the screws. This may
require extra force.
Plastic Rings
•Push the seat bottom tubes back and forth to be sure they are
secured to the seat bottom. If the seat bottom tubes move, you
have probably not fastened them properly. Remove the screws
and check to be sure the screw holes in the seat bottom tubes
and seat bottom plastic rings are aligned. Replace and tighten
the screws.
Seat Bottom Tubes
Plastic Rings
2
•Slide a seat bottom tube through each set of plastic rings on
the seat bottom.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Insert Screws Here
Hinge
Hinge Rod
4
6
•Insert two #10 x 2,2 cm black screws through the footrest
and into the seat bottom. Tighten the screws. This may require
extra force.
•Turn the seat assembly face down.
•Insert the hinge rod through the hinge on the seat back and
seat bottom, as shown.
•Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten
the screw.
Seat Back Pin
Seat Back Pin
•Set the seat assembly aside for Assembly step 9.
Slot
Slot
5
•Turn the seat bottom assembly upright.
•Fit the seat back pins into the slots in the top side of the seat
bottom assembly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Frame Leg
Seat Height Adjusters
Position 4
Frame Decorated Side
Press Lever
Frame Back Legs
8
•While pressing the levers on the seat height adjusters, lift them
to position 4 on the frame front legs, as shown.
Seat Assembly
Base
Screw Retainers
Sockets
7
•Pull the frame leg out on each frame to open. Make sure it
"clicks" into place.
•Position a frame so that the decorated side is outward.
•Fit the end of a base into the back leg of a frame.
•Fit a screw retainer over the hole in the back leg, as shown.
•Insert a #10 x 2,2 cm black screw through the screw retainer
and back leg. Tighten the screw.
•Repeat this procedure to fasten the other frame back leg to the
other side of the base.
Hint: The #10 x 2,2 cm black screws may have been assembled to
Seat Bottom Tubes
9
•Fit the seat assembly between the frames.
•Insert the seat bottom tubes into the sockets in each seat
height adjuster.
the screw retainers.
Hints:
•Be sure the seat height adjusters are in the same position
(position 4).
•You may need to push the frames apart slightly to fit the seat
bottom tubes into the seat height adjuster sockets.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
PUSH
PUSH
Screw Retainers
Base
Seat Bottom Tube Ends
10
11
•Insert the frame front legs onto the remaining base.
•Fit a screw retainer over a hole in the front leg.
•Insert a #10 x 2,2 cm black screw through the screw retainer
and front leg. Tighten the screw.
•Repeat this procedure to secure the other end of the base with
•Push each seat height adjuster to be sure they are completely on
the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each seat height adjuster and
the ends of the seat bottom tube. Tighten the screws. This may
require extra force.
the remaining screw retainer and #10 x 2,2 cm black screw.
Hint: The #10 x 2,2 cm black screws may have been assembled
to the screw retainers.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Shoulder Straps
Seat Bottom Tube Ends
Crotch Strap
14
•Remove both shoulder straps from the seat back.
•Remove the crotch strap from the seat back.
Seat Height Adjusters
12
•Push each seat height adjuster to be sure they are completely on
the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each seat height adjuster and
the ends of the seat bottom tube. Tighten the screws. This may
require extra force.
PRESS
PRESS
13
15
•Squeeze the restraint release tabs together.
•Remove the ends of the restraint system from the peg.
•Fit the pocket on the top of the pad onto the seat back.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Shoulder
Straps Up
Clips
Lowest Slot
Crotch
Strap Down
16
•Fit the clips on the front edge of the pad onto the seat bottom.
•Hook the elastic loops on each side of the pad onto the tabs in
the seat back.
17
Hint: Do not unbuckle the restraint system. It is easier to attach or
re-attach it to the product if it is buckled.
•Grasp the restraint system so that the shoulder straps are up
and the crotch strap is down.
•Insert the end of the crotch strap through the lowest slot in the
pad and the seat back.
•From behind the product, attach the end of the crotch strap to
the peg.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Shoulder
Straps
18
Smaller Baby
•Insert the ends of the shoulder straps through the lower slots in
the pad.
•From behind the product, attach the ends of the shoulder straps
to the peg.
19
Larger Baby
•From the front of the product, insert the ends of the
shoulder straps through the upper slots in the pad and
seat back.
•From behind the product, attach the ends of the shoulder
straps to the peg.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure Child
Adjuster
WARNING
Prevent serious injury or death from
falls or sliding out: The child should at all
times wear a safety harness correctly fitted
and adjusted. The tray is not designed to
hold the child in the chair.
Free End
Anchored End
Waist/Shoulder Belt
Waist/Shoulder Belt
TIGHTEN
2
•To tighten the waist straps: Feed the anchored end of the
waist strap up through the buckle to form a loop A. Pull the
free end of the waist strap B.
•To tighten the shoulder straps: Hold the adjuster and pull the
shoulder strap down C.
Adjuster
Free End
Crotch Belt
1
Anchored End
•Place your child in the seat. Position the crotch belt between
your child’s legs.
•Fasten both waist/shoulder belts to each side of the crotch belt.
Make sure you hear a "click" on both sides.
LOOSEN
3
•Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
To loosen the waist straps: ABCNote:
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure Child
Shoulder Straps
Shoulder Straps
PRESS
PRESS
PRESS
PRESS
5
4
•You can remove the shoulder straps and use only the
waist restraint.
To change strap slots:
•From behind the product, squeeze the restraint release tabs
and remove the shoulder straps.
•From behind the product, squeeze the restraint release tabs and
remove the shoulder straps.
•From the front of the high chair, pull the shoulder portions
of the restraint system out and then fit them back through
the desired shoulder strap slots in the seat pad and in the
seat back.
•From behind the product, attach the ends of the shoulder
straps to the peg.
•From the front of the product, pull to remove the shoulder straps
from the seat back/pad.
•Push to remove the shoulder straps from the waist restraint
buckle slots.
•Store the shoulder straps in a safe in a safe place for future use.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Trays
WARNING
Prevent serious injury or death from
falls or sliding out: The child should at all
times wear a safety harness correctly fitted
and adjusted. The tray is not designed to
hold the child in the chair.
PUSH
Base Tray
7
•While pushing the release bar on the front of the base tray,
adjust the base tray forward or backward.
Armrest
PUSH
6
8
•Fit the base tray onto the seat armrests. Push down until the
base tray "snaps" into place.
Hint: Before use, thorougly wash all parts (the trays) that may
•While pushing the release bar on the front of the base tray, pull
the tray base towards you and remove.
contact food. The base tray is not dishwasher safe.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Trays
Using the Teether Toy
Teether Toy
Food Tray
Base Tray
Tab
9
Slot
•Fit the food tray into the base tray, as shown.
Hint: Before use, thorougly wash all parts (the trays) that may
contact food. The food tray is not microwave safe.
Tab
10
•Insert and “snap” the teether toy tab into either slot in the tray.
Hint: To remove the teether toy, press the tab and lift the toy.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Seat
Hint: Adjust the seat height to any of seven positions!
WARNING
Prevent serious injury or death from
falls or sliding out. It is recommended
that only children capable of sitting upright
unassisted use the high chair in the
upright position.
Seat Height Adjuster
Hint: Adjust the seat angle to any of three positions: Upright,
Semi-Recline or Recline.
Press Lever
Upright
Semi-Recline
12
Recline
To adjust the seat height:
•Press the levers on both seat height adjusters and lift or lower
the seat to the desired height.
•Make sure both sides of the seat are adjusted to the same
height. Push the seat bottom to be sure the seat is locked
in place.
SQUEEZE
11
To adjust the seat angle:
•Squeeze the seat back handle and push the seat back forward
or, pull it backwards to the desired position.
•Push the seat back to be sure it is latched in position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
Care
•The pad, frame and base tray may be wiped clean using a mild
cleaning solution and a damp cloth.
•The restraint system may be wiped clean or is machine
washable. Machine wash in cold water on the gentle cycle. Do
not use bleach. Line dry.
•The food tray, teether toy and restraint system are also top rack
dishwasher safe (or use bottom rack - without using the
drying cycle).
Pull Frame
Release Latch
To remove the pad:
•Remove the elastic loops from the pegs on the back of the seat.
•From behind the product, squeeze the restraint release tabs and
remove the restraint system from the peg.
•From the front of the product, pull to remove the restraint system.
•Unfasten the pad hooks from the front edge of the seat. Lift the
top of the pad off of the seat back.
•To replace the pad: refer to Assembly steps 13-19.
IMPORTANT! Never use this product without the restraint
system. Replace the waist/shoulder belts and crotch belt.
13
•With the legs all the way open, lower the seat to position 7 the
lowest position).
•Pull the frame release latches forward and push the rear legs
toward the front legs.
L0542e-0726
PRINTED IN MEXICO
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|