Iridium 10i
Iridium 12i
Iridium 15
ULTIMATE Iridium
SERIES SUBWOOFERS
WELCOME
SUBWOOFER ENCLOSURES, GENERAL
Thank you for buying a DLS ULTIMATE Iridium subwoofer.
The subwoofer must be installed correctly in order to work well.
This manual will show you how to install it like a pro. Please
read the entire manual before beginning the installation.
Install the subwoofer yourself if you feel confident with our
instructions and if you have the proper tools. However if you
feel unsure, turn over the installation job to someone better
suited to it.
Build your enclosure in a stable and airtight material. The best
is MDF-board, 19 mm, or particle board, 22 mm. Larger
enclosures must have bracing inside to avoid vibrations. The
enclosure must be completely airtight. Use sealing compound
in all joints, also around the cable terminals. The size of the
enclosure is decided by the speaker data.
SEALED ENCLOSURES
The speakers are designed for enclosure mounting. In "open
air" installations the power handling capacity is reduced by 30%
from the nominal value. We dont recommend ”open air”
installations for Ultimate Iridium subwooers.
Sealed enclosures are easy to build. The size is not critical, but
it can´t be too small. The speaker data such as Fs, Qts, Vas
and X-max decides the size of the enclosure.
Large speakers need larger boxes. Two speakers need a box
of the double size etc. The enclosure must be completely air-
tight.
CONNECTION OF SUBWOOFER
A sealed enclosure should be filled with acoustic wool up to 75
- 100%.
How to connect depends on what type of amplifier you use.
The best is to follow the instructions given in the manual for the
amplifier. Most amplifiers today have built-in lowpass crossover
and possibilities to connect your subwoofer in bridge mode.
Two 4 ohm subwoofers are often connected in stereo mode
since most amplifiers can´t handle bridge mode loads below 4
ohms.
A sealed enclosure has a lower efficiency than a vented
enclosure, but they can handle high power and are easy to build.
A subwoofer in a sealed enclosure creates a tight bass suitable
for the audiophiles listening to classical music, jazz and soft
rock.
The Iridium subwoofers have dual, four ohm, voice coils. Each
voice coil has an impedance of 4 ohms. If they are connected in
series the resulting impedance is 8 ohms. If they are connected
in parallel the resulting impedance is 2 ohms. Make sure to
connect in a way that don´t ruin the amplifier. If you have a DLS
Ultimate amplifier it´s possible to connect the voice coils in
parallel, these ampliers are 1 ohm stable.
VENTED ENCLOSURES
A speaker in a vented enclosure has a higher efficiency (+3 dB)
and higher power handling capacity than in a sealed enclosure.
In a vented enclosure the sound from the speaker and the port
work together creating a higher sound level. The sound from
the port must come out in the same phase as from the speaker
otherwise the result is bad.
The size of the vented enclosure is decided by the speaker
data just as for the sealed one.
We also recommend the use of a subsonic highpass filter. This
gives a better bass reproduction with less "rumble". In most
DLS amplifiers this feature is already built-in.
The size of the vehicle often decides the practical size of the
enclosure. Asmaller enclosure has a higher resonant frequency
than the larger one. The size of the enclosure should not be so
big that the speaker plays below it´s own free air resonance
(Fs), then it loose in power handling capacity.
For wiring use high class speaker wires, minAWG13 (2.5 mm2).
For example DLS SC 2x4.
The port does not have to be fully inside the enclosure as long
as the area and length are correct. Sometimes you need two or
more ports in an enclosure. You can convert from one to two or
more ports as long as the total port area is the same.
ENCLOSURE DAMPING
Most enclosures should be damped inside with syntetic
(acoustic) wool or damping mat (line). Attach the damping ma-
terial on the wall opposite from the speaker and port. A sealed
enclosure should be filled up to 70-100% with acoustic wool.
RUNNING-IN PERIOD
IMPORTANT!
Think of the speaker weight when you install it. If you don´t
mount it properly it can come loose.
Allow the speaker to play for at least 15-20 hours. After this
time the performance is correct.
WARRANTY SERVICE
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is retur-
ned for service, please include the original dated receipt with
the product.
ꢀ Technical Assistance
For technical assistance ask the shop where the product was
sold or the distributor in your very country.You can always phone
the DLS Helpdesk in Sweden + 46 31 840060 or send an e-
mail to [email protected]
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: [email protected]
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THE RECOMMENDED ENCLOSURES
The performance of these recommended enclosures will
vary from vehicle to vehicle. It is more difficult to get a
tight and well defined bass in a SEDAN vehicle because
of the tightness between trunk and interior. In most cases
the recommended enclusures below is the best choise.
The vented box is to be preferred.
ENCLOSURE PLACING IN DIFFERENT TYPES OF
VEHICLES
In small vehicles like VW Golf, Peugeot 306 and similar the
bass box should be installed with both speaker and port directed
backwards.Alternatively booth speaker and port can be directed
upwards. This way of mounting is valid for all types of vehicles
where the trunk is incorporated with the inner compartment.
- The given enclosure volume is the inner volume.
In sedan vehicles with the passenger compartment separated
from the trunk, the enclosure should be installed with booth
speaker and port directed towards the rear seat. Some cars
have an opening in the middle of the rear seat for loading skis
etc. You can install the enclosure behind this opening and direct
speaker or port through this opening. There must be some free
space in front of the port, (between the rear seat and the port
opening).
- Volumes occupied by speaker and ports have already
been added to the given enclosure volumes so don’t add
any volume.
- Use conical bass ports for best result. (DLS BP75 for
Iridium 10i & 12i, BP110 for Iridium 15). Cut the tube to
the correct length.
There are two flanges coming with this kit. The larger
one is for the outside, and the smaller one should be
attached to the tube inside the enclosure.
Make a round hole in the box where you want to mount
the bass port.
In large vehicles like station wagons the best sound is achieved
with the enclosure installed behind the rear seat with booth spea-
ker and port directed backwards. Alternatively you can install
the enclosure on one side of the luggage compartment.
The larger flange should beattached to the outside of
the box. Fasten it to the box with screws or with some
glue. There are prepared drill holes on the back of the
flange.
The smaller flange is for the inner end of the tube. Use
a PVC-glue to attach it on the tube.
Then glue the tube to the port mounted in the box.
Use sealing compound round the flange to make the
box as airtight as possible.
CALCULATE YOUR OWN ENCLOSURE
Box volumes:
When calculating the inner volume of an enclosure you just
multiply the width (W) x height (H) x depth (D).
Use measures in dm and you will get the answer in liters.
A trapezoid box is calulated as this:
Vol=width (W) x height (H) x upper depth (UD) + lower depth (LD)
W
2
Be sure to measure the
inside dimensions.
UD
H
LD
Vented enclosure:
RECOMMENDED ENCLOSURES Iridium 10i
Wiring
Volume
Port*
Damping
F3
: Use parallel V/C
: 25 / 0,88 (litre / ft3)
: 3”(6,8 cm) x 38 cm / 15”
: Line inside
Sealed enclosure:
Wiring
Volume
Damping
F3
: Use single V/C
: 22 / 0,78 (litre / ft3)
: Acoustic wool
: 40 Hz
Width
Upper
depth
: 31,7 Hz
* Use the BP 75 port kit . Mount the flanges
on the tube ends. The port should be on the
side of the enclosure.
Cut the tube to it’s correct length.
Outside box dimensions:
Outside box dimensions:
Width
Height
Lower depth
Upper depth
Material
: 529 mm (20,83”)
: 320 mm (12,60”)
: 247 mm (9,72”)
: 147 mm (5,79”)
: MDF 19 mm (3/4”)
VENTED
Width
Height
Lower depth
Upper depth
Material
: 599 mm (23,58”)
: 320 mm (12,60”)
: 247 mm (9,72”)
: 147 mm (5,79”)
: MDF 19 mm (3/4”)
For best result, use any of these
recommended enclosures.
If you want to modify the dimensions,
use the calculation methods
described above.
Depth 599
341
730
730
SEALED
Depth 599
114
730
114
Depth 529
730
730
Depth 599
320
341
599
247
282
2 pcs
529
247
Depth 529
730
114
114
202
Technical drawing for a
22 litre enclosure.
The Iridium 10i can work well in
a 22 litre sealed enclosure.
Here is the drawing for the box
and the separate boards needed
to build a suitable enclosure.
Technical drawing for a
25 litre enclosure.
The Iridium 10i can work well in
a 25 litre vented enclosure.
Here is the drawing for the box
and the separate boards needed
to build a suitable enclosure.
Depth 529
320
Depth 529
208
282
730
2 pcs
202
Depth 599
730
208
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOMMENDED ENCLOSURES for Iridium 12i
Width
Vented enclosure:
Wiring
Volume
Port*
Damping
F3
: Parallel VC
: 36,5 / 1,29 (litre / ft3)
: 3”(6,8 cm) x 27 cm / 10,63”
: Line inside
Upper
depth
: 32 Hz
* Use the port included in the subwoofer
packing.Mount the flanges on the tube ends.
Dont cut the tube, it has the correct length.
Outside box dimensions:
SEALED
Sealed enclosure:
Wiring
Volume
Damping
F3
Outside box dimensions:
Width
Height
Lower depth
Upper depth
Material
: Parallel VC
VENTED
: 19,3 / 0,67 (litre / ft3)
: Acoustic wool
: 56 Hz
Width
Height
: 550 mm (17,72”)
: 350 mm (13,78”)
: 313 mm (12,32”)
: 213 mm (8,39”)
: MDF 19 mm (0,75”)
Lower depth
Upper depth
Material
For best result, use any of these
recommended enclosures.
If you want to modify the dimensions,
use the calculation methods
described on previous page.
: 400 mm (15,75”)
: 350 mm (13,78”)
: 256 mm (10,08”)
: 156 mm (6,14”)
: MDF 19 mm (0,75”)
Technical drawing for a
19,3 litre enclosure.
Technical drawing for a
36,5 litre enclosure.
123
180
Depth 400
740
740
740
Depth 550
740
740
740
370
370
312
312
Depth 400
123
Depth 550
180
2 pcs
269
2 pcs
212
Depth 400
350
Depth 550
350
Depth 400
740
Depth 550
274
400
256
740
313
550
217
RECOMMENDED ENCLOSURES for Iridium 15
Width
Upper
depth
VENTED
SEALED
600
304
170
Lower
depth
278
600
144
Sealed enclosure:
Vented enclosure:
Wiring
Volume
Damping
F3
: Single VC
Wiring
Volume
Port*
Damping
F3
: Parallel VC
: 50 / 1,765 (litre / ft3)
: 4”(10,3 cm) x 31 cm / 12,2”
: Line inside
: 38,3 Hz
: 45,5 / 1,6 (litre / ft3)
: Acoustic wool
: 44,6 Hz
412
422
2 pcs
235
2 pcs
261
Outside box dimensions:
Width
Height
Lower depth
Upper depth
Material
* Use the BP 110 port kit . Mount the flanges
on the tube ends. The port should be on the
side of the enclosure.
: 600 mm (23,62”)
: 460 mm (18,11”)
: 278 mm (10,94”)
: 178 mm (7,01”)
: MDF 19 mm (3/4”)
Cut the tube to it’s correct length.
Depth 600
266
Depth 600
240
780
770
Outside box dimensions:
Width
Height
Lower depth
Upper depth
Material
: 600 mm (23,62”)
: 450 mm (17,71”)
: 304 mm (11,96”)
: 204 mm (8,03”)
: MDF 19 mm (0,75”)
Technical drawing for a
45 litre enclosure.
Depth 600
475
Depth 600
465
780
780
780
770
770
The Iridium 15 works well in a
45 litre sealed enclosure.
This is a drawing for the 45
litre box and the separate
boards needed to build a
suitable enclosure.
Technical drawing for a
50 litre enclosure.
Depth 600
144
Depth 600
770
170
The Iridium 15 works well in
a 50 litre vented enclosure.
This is a drawing for the 50
litre box and the separate
boards needed to build a
suitable enclosure.
Depth 600
460
Depth 600
450
For best result, use any of these
recommended enclosures.
If you want to modify the dimensions,
use the calculation methods
described on previous page.
Download from Www.Somanuals.com. All Manuals Search And Download.
|