CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FAN INSTALLATION (USA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FAN INSTALLATION (OUTSIDE USA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CONTROL FEATURES:
3-SPEED CONTROL WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3-SPEED OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner’s manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electri-
cian should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If
more than one fan is being installed, be
careful not to mix blades from different
cartons.
FUSE BOX
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
18"
70"
• When cleaning, painting, or working near
your fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
CIRCUIT BREAKER
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
84"
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged
in any way. Contact Casablanca Fan Company
by calling toll free 1-888-227-2178, or
contact your local authorized Casablanca
dealer for assistance in obtaining service.
PN 8443011 AT1008
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FOUR SEASONS™ III
PREPARATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging material, be certain that all parts have been removed.
GETTING STARTED
Carton Contents
Be sure to use only genuine Casablanca blades. The blade
shrink wrap holds 5 blades of matched weight. If more than
one fan is being installed, be sure not to mix blade sets.
The fan carton contains the fan body, warranty card, owner's
manual, and all the parts necessary to assemble and install
your Casablanca ceiling fan. These parts are shown at the
start of each installation section. Before you start, go through
this Owner’s Manual and confirm that you have all the parts
shown in each section.
CAUTION: When removing the shrink wrap,
be careful not to scratch the blades.
PERMA LOCK™ HARDWARE
•
ALLEN SET SCREW
DOWNROD & BALL
ASSEMBLY
1
4
-20 x 1
4
"
3mm
ALLEN WRENCH
(PRE-INSTALLED)
FAN PREPARATION
IMPORTANT SAFETY INFORMATION!
BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE
THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY
MOTOR
WIRES
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
GROUND
WIRE
Perma Lock™ downrod and ball assembly.
•
Tip: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
DOWNROD
& BALL
ASSEMBLY
Step B. Using the provided allen wrench, loosen the set screw
several turns to allow installation of the downrod. Thread
the downrod into the motor coupling until it stops turning,
this will take at least four and a half full turns.
TAPERED
THREAD
Step C. Securely tighten the set screw with the provided allen
wrench to ensure safe operation of your fan.
ALLEN
SET SCREW
CAUTION: Failure to fully lock in the down-
rod before securely tightening the allen set
screw may cause the fan to separate from
the downrod during normal operation!
MOTOR
COUPLING
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
Using Existing Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish After turning the power OFF at its source (either circuit breaker
to place your Casablanca fan, an approved ceiling fixture or fuse box), lower the old fixture and disconnect the wiring.
outlet box must be installed and wired.
Check the ceiling fixture outlet box to be sure that it is
marked ‘Approved for ceiling fan mounting’. If it is not, a new
box must be installed.
WARNING: To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box marked
acceptable for ceiling fan support using the
mounting hardware provided with the outlet box.
NOTE: The fan weight is 17 pounds.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FOUR SEASONS™ III
CROSSBAR MOUNTING BRACKET INSTALLATION
CEILING FAN
APPROVED
WIRING BOX
FOR FAN INSTALLATION OUTSIDE THE
USA GO TO PAGE 8
EXCLUDING MODELS ENDING IN ‘E’
Proceed with installation as follows:
Step 1. Route the wires from the ceiling outlet box through
the crossbar mounting bracket center hole. Attach the bracket,
with ground wire and ridges down, to the ceiling fixture outlet
box with the mounting hardware included with the outlet
box.
CEILING
WIRING
CROSSBAR
MOUNTING
BRACKET
RIDGE
SIDE
DOWN
Tighten the screws firmly by hand only, being careful not to
bend the bracket by over tightening.
FLAT
WASHER
CAUTION: To reduce the risk of
personal injury, use only the
mounting hardware provided with
the approved outlet box to install
the crossbar mounting bracket.
GREEN
GROUND
WIRE
APPROVED
OUTLET
BOX
HARDWARE
CANOPY HARDWARE
CANOPY SCREW (4)
CANOPY LOCK WASHER (4)
CANOPY
HATCH
CANOPY
CANOPY INSTALLATION
CROSSBAR
MOUNTING
BRACKET
Step 2. Attach the canopy to the crossbar
mounting bracket with three of the 8-32 x 21/4"
long canopy screws and canopy lock washers.
Tighten the screw firmly by hand only.
NOTE: On sloped ceilings, align the
canopy opening towards the top or
room peak.
CANOPY
CANOPY LOCK
WASHER
CANOPY
SCREW
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOUR SEASONS™ III
CROSSBAR MOHUANNTIGNIGNGBRTHACEKFEATNINSTALLATION
Step 7. To hang the fan body in the canopy,
hold the fan body firmly and insert the ball
into the canopy opening. Check that no wires
were pinched. Rotate the fan body until the
slot in the nylon ball fits into the pin opposite
the canopy opening.
BALL
D1
OPTION
WIRE
NOTE: The fan weight is 17 pounds.
NOTE: Independent control of the
light fixture using a W-8 requires an
additional power wire run from the
wall switch to the fan. See Page 12
for wiring.
SLOT
PIN
CAPPED BLUE D1-OPTION WIRE ON 3-SPEED ONLY
FOR INDEPENDENT W-8 LIGHT CONTROL
CANOPY ELECTRICAL CONNECTIONS
PULL CHAIN OR
W-4 CONNECTIONS
Step 8a. Attach the fan wires to the ceiling fixture outlet WIRE NUT
box wiring by twisting the bare ends of the wires together
and then securing with a wire nut. Test that the connection
is secure by pulling on the wire nut. Connect in this order:
2 BLACK & BLUE
D1-OPTION WIRES
(WITHOUT W-8)
Step 8b. Pull Chain or W-4 Wiring Connections
• GREEN leads from mounting plate and fan to GROUND
conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling fixture
outlet box. Secure with wire nut.
2 WHITE WIRES
• BLUE wire and BLACK power wire from fan to BLACK power
wire in ceiling outlet box. Secure with wire nut.
3 GREEN WIRES
Step 8c. W-8 Wiring Connections
W-8 CONNECTIONS
• GREEN leads from mounting plate and fan to GROUND
conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
BLUE & YELLOW
WIRES
BLACK & RED
WIRES
• BLACK power wire from fan to RED wire from W-8 in ceiling
outlet box. Secure with wire nut.
• BLUE wire from fan to YELLOW wire from W-8 in ceiling
outlet box. Secure with wire nut.
2 WHITE WIRES
3 GREEN WIRES
NOTE: SEE PAGE 12 FOR ADDITIONAL WIRING INFORMATION.
CANOPY HATCH INSTALLATION
Step 9. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are on
opposite sides of the canopy and all wires
are clear of the canopy opening.
CANOPY
HATCH
Step 10. Install canopy hatch with the
last canopy screw and lock washer. To do
this, tilt the fan body away from the hatch
opening.
LOCK
WASHER
TILT THE
FAN TO
INSTALL
LAST
CANOPY
SCREW
Tighten the screws firmly by hand only.
Step 11. Straighten the fan, then check
to ensure that there is no movement
between the canopy and ceiling or Hang-
Tru ball and top support shaft.
CANOPY
SCREW
6
Download from Www.Somanuals.com. All Manuals Search And Download.
®
FOUR SEASONS III
blade & blade holder hardware
FIber FlaT waSher
FIber FlaT waSher
PaGe 14.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
lIghT FIxTure InSTallaTIon
LIGHT FIXTURE HaRdwaRE (not to scale)
bowl (1)
FInIal (1)
60-waTT Candelabra
bulbS (2)
PullChaIn
exTenderS (2)
CaP (1)
lIghT KIT FITTer (1)
Step 13. Remove light kit fitter from carton.
Using the provided Phillips screwdriver, unscrew the three
screws from the fan and set aside.
Connect the 9-pin connector from the fan to the connector
on the light kit fitter as shown, aligning the red squares
and making sure they snap into place.
9-PIn ConneCTor
lIghT KIT FITTer
Connect the light fitter to the bottom of the fan as shown,
tucking the exposed wires into the fitter, and aligning the
screw holes. Using the three screws, attach the light kit
fitter to the fan.
SCrewS
Screw the two 60-Watt lightbulbs onto the light kit fitter.
Fish the pullchain through the center holes of the metal
disk of the light kit fitter. Continue to fish the pullchain
through the bowl and cap. Fit bowl and cap around the
light kit fitter.
Using the finial, attach the bowl and cap to the light kit
fitter.
Attach pullchains on light kit fitter to pullchain extenders.
bowl
Note: In compliance with US Federal Energy Regula-
tions, this ceiling fan contains a device that restricts
the light kit to a maximum of 190 watts. Exceeding
that limit or the marked limit on this product may
result in fire hazard or improper operation.
CaP
FInIal
8
Download from Www.Somanuals.com. All Manuals Search And Download.
®
FOUR SEASONS III
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FOUR SEASONS™ III (OUTSIDE USA INSTALLATION)
FAN INSTALLATION OUTSIDE THE USA - EXCLUDING MODELS ENDING IN ‘E’
If you do not have an existing fixture located where you wish to place your Casablanca fan, a new ceiling fixture outlet box
must be installed (use an outlet box marked acceptable for fan support) and an electrical cable to run it. This box must be
secured to the ceiling according to the outlet box manufacturer’s instructions. It is recommended that this be done by
a qualified electrician.
Vaulted or Cathedral Ceiling Installations
Your Casablanca fan may be installed on a vaulted or cathedral ceiling in the same manner as described for a flat ceiling. The
Hang-Tru® mounting system makes it possible to hang your fan on sloped ceilings up to a 32° angle.
Using Existing Ceiling Fixture Outlet Box
After turning electrical power off, lower the old fixture to expose the wiring and the ceiling fixture outlet box. Cut the
fixture wires or if wire nuts have been used, unscrew them and disconnect the wires. The fixture can then be removed.
After removing the old fixture, check the outlet box to sure that it is supported by a joist or beam across its upper surface.
If not, a 2" x 4" stud must be installed.
OUTSIDE USA - SECONDARY SUPPORT INSTALLATION PARTS
OUTLET
ADAPTOR
PLATE
3
6" OUTLET BOX
CABLE
8"- 7 LAG SCREW (5")
FENDER
WASHER
SPRING LOCK
HOOK
OUTSIDE USA - MOUNTING SECONDARY SUPPORT PARTS TO OUTLET BOX
JOIST
1WARNING: MOUNT ONLY TO AN OUTLET BOX
OR
MARKED ACCEPTABLE FOR FAN SUPPORT
BEAM
••••
ADVERTISSEMENT: ASSEMBLER UNIQUEMENT À
UNE BÔITE DE SORTIE JUGÉE ACCEPTABLE POUR
RETENIR UN VENTILATEUR.
Before beginning Step 1, follow Steps A-C on Page 3.
OUTLET
BOX
1
4" GUIDE
HOLE
Step 1. Remove the knockout plug in the center of the outlet
box or drill a 1⁄2" hole for the lag screw to pass through. Then
1
drill a ⁄4" guide hole into the joist or beam to a depth of
3 inches.
CROSSBAR
MOUNTING
BRACKET
Step 2. Route the outlet box wires through the 1⁄2" diameter
outer hole of the outlet adaptor plate.
1
"
2
HOLE
Step 3. Line up the slotted holes and four canopy screw
holes in the crossbar mounting bracket and outlet adaptor
plate with the 8-32 mounting holes in the outlet box. Install
the two 8-32 X 21⁄4" (1") screws and flat washers in fan
hardware kit and tighten securely by hand only!
OUTLET
ADAPTOR
PLATE
Step 4. With fender washer and outlet box cable attached as
shown, pass lag screw through center hole of outlet adaptor
plate and screw into pre drilled 1⁄4" guide hole of joist. Tighten
until outlet box is firmly mounted.
8-32 X 21 "
(1") SCRE4W
LAG
SCREW
TIP: Threading two of the canopy screws into the
crossbar mounting bracket will help everything stay
aligned as you tighten the lag screw. Remove them
before starting Step 12.
FENDER
WASHER
6" OUTLET BOX
CABLE
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FOUR SEASONS™ III (OUTSIDE USA INSTALLATION)
OUTSIDE USA - SECONDARY SUPPORT ♦ PREPARING THE SWITCH HOUSING
Step 5. Hold the switch housing close to the fan
and connect the motor plug to the switch housing
socket. The connectors are keyed to ensure correct
alignment during installation - Do not force!
SWITCH
HOUSING
Step 6. Locate the blue and white LIGHT wires in
the switch housing. Make sure they are NOT
connected.
Step 7. Check the tightness of the Cable Clamp &
Screw. (The clamp should not slip along the cable.)
SWITCH
Step 8. Tape completely over the end of the Cable
Clamp and the end of the Secondary Support Cable
with electrical tape.
HOUSING
CONNECTOR
(SOCKET)
CABLE
CLAMP
& SCREW
MOTOR
CONNECTOR
(PLUG)
TAPED OVER
CABLE CLAMP
& SCREW
SECONDARY
SUPPORT
CABLE
SWITCH
HOUSING
PLATE
NYLON
STOP
Step 9. Pull the cable through the other side of
the fan to snug the cable clamp. This makes it
easier to install the switch housing.
MOUNTING
SCREW
(3)
Step 10. Remove the three mounting screws from
the switch housing plate. (Keep them for the next
step).
OUTSIDE USA - SECONDARY SUPPORT ♦ SWITCH HOUSING INSTALLATION
Step 11. Position the switch housing assembly on
the switch housing plate and align the holes in
the switch housing with the holes in the plate.
Secure the switch housing assembly by reinstalling
MOUNTING
the three screws removed in the previous step.
SCREW
(3)
CAUTION! Do not pinch wires
between the switch housing
assembly and the plate.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FOUR SEASONS™ III (OUTSIDE USA INSTALLATION)
OUTSIDE USA - SECONDARY SUPPORT ♦ CANOPY INSTALLATION
Step 12. Attach the canopy to the crossbar mounting bracket behind
1
2
the installed outlet adaptor plate with three of the 8-32 x 2 ⁄ " long
canopy screws and lock washers provided with your Casablanca fan.
Hand tighten until snug against the ceiling.
NOTE: On sloped ceilings, align the canopy opening
toward the top or peak of the room.
Step 13. Attach the spring lock hook to the fan cable by depressing
the spring lock and clipping onto the loop at the end.
FAN
CABLE
SPRING
LOCK
SPRING
FEED OUTLET BOX
LOCK HOOK
CABLE AND OUTLET
BOX WIRES
THROUGH CANOPY
OPENING
CANOPY
LOCK
WASHER
CANOPY
SCREW
OUTSIDE USA - SECONDARY SUPPORT ♦ HANGING THE FAN
Step 14. To hang the fan body in the canopy, hold
the fan body firmly and insert the nylon ball into the
canopy opening. Rotate fan body until slot on nylon
OUTLET
BOX
CABLE
CANOPY
ball fits into pin opposite canopy opening.
Step 15. Attach the fan wires to the ceiling outlet
box wiring by twisting the bare ends of the wiring
together:
FAN
CABLE
• White wire from fan to white NEUTRAL wire in ceiling
outlet box.
• Black wire and blue wire from fan to black (or red)
POWER wire in ceiling outlet box.
• Green leads from crossbar mounting bracket and
fan to grounding conductor of power source.
Secure by threading on the wire nuts provided with
the fan.
PIN
BALL
SLOT
NOTE: SEE PAGE 12 FOR ADDITIONAL WIRING
INSTRUCTIONS.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FOUR SEASONS™ III (OUTSIDE USA INSTALLATION)
OUTSIDE USA - SECONDARY SUPPORT ♦ COMPLETING INSTALLATION
Step 16. Attach the fan cable to outlet box cable with the
spring lock hook. Make sure the spring lock is tightly closed.
WIRE NUTS
INSTALLED
Step 17. Tuck the wires into the canopy with the wire nuts
pointed upward, so that the white and black wires are on
opposite sides of the canopy and all wires are clear of the
canopy opening. Tuck the extra cable and screw lock hook
into the canopy.
FAN AND OUTLET
CABLES SECURED BY
SPRING LOCK HOOK
NOTE: International fans and light fixtures are supplied
with plug and socket connectors. Substitute these connectors
for the wire nuts shown throughout this manual.
OUTSIDE USA - BLADE & BLADE HOLDER HARDWARE
BLADE
HOLDER
BLADE SCREW
(3 PER BLADE)
FLAT WASHER
(3 PER BLADE)
BLADE HOLDER SCREW
(2 PER BLADE)
OUTSIDE USA - BLADE & BLADE HOLDER INSTALLATION
Step 18. Attach the blades to the
blade holders with the three blade
screws and flat washers provided
for each blade. Hand tighten
securely.
Step 19. Install the assembled
blade and blade holder to the fan
motor. Hand tighten securely.
Repete for each assembly.
BLADE SCREW
(3 PER BLADE)
Step 20. Attach the pull chain fob.
PROCEED TO PAGE 8.
FLAT WASHER
(3 PER BLADE)
BLADE HOLDER
SCREW
(2 PER BLADE
HOLDER)
FOB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3-SPEED
3-SPEED ♦ W-4 WALL CONTROL OF THE FAN
• The W-4 allows the choice of four (4)
different speed settings.
• No light fixture is used.
• Set the FAN pull chain switch to the
HIGH speed setting.
• No changes in household or fan wiring
are required.
• The fan may be turned ON and OFF by
the W-4 wall control.
CAUTION! Failure to set the pull-chain
speed to HIGH can result in faulty
operation of the fan and damage to
the W-4 wall control. To confirm fan
is set to HIGH: Turn W-4 fan speed
switch to 'HI' - set fastest fan speed
with pull chain.
R
3-SPEED ♦ W-8 WALL CONTROL OF THE FAN & LIGHT(S)
• The fan may be turned ON and OFF
by the W-8 wall control.
• The lights may be turned ON and
OFF by the W-8 and the intensity
adjusted from low to high.
• The fan must be supplied with two
independent 120V AC supply
wires.
• Set the FAN pull chain switch to
the HIGH speed setting.
• Turn the lights ON at the fan.
• The W-8 allows the choice of four
(4) different speed settings.
CAUTION! Failure to set the pull-
chain speed to HIGH can result in
faulty operation of the fan and
damage to the W-8 wall control.
To confirm fan is set to HIGH: Turn
W-8 fan speed switch to 'HI' - set
fastest fan speed with pull chain.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3-SPEED
3-SPEED ♦ OPERATION
Pull-chain switches on the fan control the fan and lights.
LIGHT
PULL CHAIN
SWITCH
FAN & SPEED
CONTROL
PULL CHAIN SWITCH
Using the fan control pull-chain switch: Fan off at start.
• First pull: fan ON, high speed
• Second pull: medium speed
• Third pull: low speed
• Fourth pull: fan OFF
Using the optional light pull-chain switch: Light off at start.
• First pull: light ON
• Second pull: light OFF
Direction of blade rotation is controlled by the reverse slide
switch on the side of the switch housing.
No changes in household wiring are required.
REVERSE
SWITCH
3-SPEED ♦ OPTIONAL WALL CONTROL ♦ W-4
The W-4 wall control provides four-speed control of fan from a convenient wall location. The
W-4 is designed to replace a standard wall switch and will fit wall boxes with a depth of 2"
or greater. Not for use with single pull-chain fan/ light option wiring.
To install a W-4 wall control in place of an existing wall switch, follow the instructions on
the W-4 package.
Note: No rewiring is required if the fan is replacing an existing light fixture.
Operation of the fan from the wall switch is simple:
1. Turn knob to obtain desired speed setting.
CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of
the fan and damage to the W-4 wall control. To confirm fan is set to HIGH: Turn W-4 fan
speed switch to 'HI' - set fastest fan speed with pull chain.
3-SPEED ♦ OPTIONAL WALL CONTROL ♦ W-8
The W-8 wall control provides separate control of fan and light with two separate knobs from
a convenient wall location. The W-8 is designed to replace a standard wall switch and wall
boxes with a depth of 2" or greater. Requires two hot leads from wall box to ceiling wiring
box.
LO
To install a W-8 wall control in place of an existing wall switch, follow the instructions on
the W-8 package.
Operation of the fan from the wall switch is simple:
1. Turn the upper knob to the desired fan speed.
2. Turn the lower knob to the desired light setting.
CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of
the fan and damage to the W-8 wall control. To confirm fan is set to HIGH: Turn W-8 fan
speed switch to 'HI' - set fastest fan speed with pull chain.
SAVING MONEY WITH YOUR CEILING FAN
IN SUMMER, the movement of
air creates a cooling “wind chill”
effect. A room can actually feel
several degrees cooler, without set-
ting the thermostat lower.
IN WINTER, hot air rises to the
ceiling while cool air settles to the
floor. Trapped against the ceiling,
the warm air is wasted. If you turn
up the thermostat, energy costs
will rise.
RUNNING IN REVERSE, your
Casablanca fan can recirculate
warm air near the ceiling down
into the living area, providing even
heating and comfort (with a pleas-
ant effect on heating bills).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3-SPEED
TROUBLESHOOTING
BEFORE REQUESTING SERVICE:
Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth Never Lubricate this Fan!
should be used to prevent scratching the finish. A vacuum cleaner The precision motor at the heart of your Casablanca fan features
brush nozzle can remove heavier dust. Surface smudges or an accu- sealed bearings that are lubricated for life. Do not attempt to oil
mulation of dirt and dust can easily be removed by using a mild the motor.
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will Changing Light Bulbs
damage the finish. Painted and high-gloss blades may be cleaned Be sure to turn power to the fan OFF at the wall switch or circuit
in the same manner.
breaker before changing light bulbs. Replace bulbs with same type
as removed from the fixture. Each fan is rated for a maximum TOTAL
Blades: Wood finish blades should be cleaned with a furniture pol- wattage of lighting.
ishing cloth. Occasionally, a light coat of furniture polish may be Exceeding the rated maximum allowable wattage for the fan will
applied for added protection and beauty.
burn out the fan electronics module and void the warranty.
PROBLEM
3-SPEED
POSSIBLE REMEDIES..
FAN WILL NOT START
Check main circuit fuses, circuit breakers, or wall switch position.
Check all wire connections, making sure the power is turned off during this inspection.
Check that reverse switch is not set in center of throw.
FAN WOBBLES OR SHAKES Be sure canopy pin is properly set into the slot on the ball.
EXCESSIVELY
Check the screws holding the blade holders to the flywheel (or direct drive motor). Tighten as necessary.
Check that bladeholders have not been bent during installation.
FAN NOISY DURING
OPERATION
Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s) as neccessary.
Tighten the blade to bladeholder screws.
Tighten canopy screws and mounting plate assembly.
Check and tighten blade holders to flywheel (or direct drive motor).
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have
fallen off the wire splices. Tighten or adjust as necessary.
BREAK-IN PERIOD
Let fan run at high speed for two (2) hours
DOES NOT RUN ON
LOW SPEED
If new, “break-in” may be required - run at higher speed for several days
FAN RUNS SLOWLY IN EITHER DIRECTION IF ROTATION IS STARTED BY HAND; WILL NOT REVERSE: Defective reverse switch; defective
capacitor; or open motor winding: Replace reverse switch assembly; replace PCB assembly; or replace motor unit.
FAN WILL NOT OPERATE AT PROPER SPEEDS OR WILL NOT OPERATE AT ANY SPEED: Defective three-speed pull-chain switch assembly; or
defective capacitor: Replace three-speed pull-chain switch assembly; or replace PCB assembly.
For questions or to locate the nearest
Casablanca Authorized Service Center
call toll free:
1-888-227-2178
or visit us on the web at:
16
Download from Www.Somanuals.com. All Manuals Search And Download.
®
FOUR SEASONS III
Product SPecificationS
172mm x 12mm Direct Drive™
®
Model name:
Four Seasons III Gallery
Motor:
Model number: 84GxxD
Blade Span With:
Blade Pitch:
no. of Blades:
technology:
Lightbulbs:
52"
13°
5
dimensions:
A =
B =
C =
D = 11.5"
E =
13"
25"
3"
3-Speed
(2) 60-watt candelabra bulbs
NOTE: Dimension B
includes light fixture
and glass.
5.6"
Airflow:
electricity use*:
Airflow Efficiency*: 74.3 cfm/watt
5,100 cfm
80 watts
Weight:
17 lbs.
* Performance data is for fan only. No lighting wattage is included.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|