1.888.227.2178
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing your new
Casablanca® ceiling fan! It will provide
comfort and performance in your home
or office for many years. This installation
and operation manual contains complete
instructions for installing and operating
your fan.
Tools Needed
Mounting Options
Ceiling Bracket
30 inches
4
2
3
9
5
We are proud of our work and appreciate
the opportunity to supply you with the
best ceiling fan available anywhere in the
world.
Downrod
Wiring
Canopy
Wall Control
To register your fan, please visit:
Save your receipt for proof of purchase.
6
11
12
Maintenance
& Cleaning
Blades
Light Kit
Operation
Troubleshooting
?
?
?
13
14
16
18
19
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Tools Needed
Pliers
Wire Strippers
Screwdrivers
Ladder
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
O
34
CEILING
Mounting Options
If you have a flat ceiling:
Hang your fan by a standard downrod (included).
Standard
Mounting
Support
Structure
Support
Structure
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
1. You will need a longer downrod (sold separately).
Angled
Mounting
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Ceiling
Angled
(required)
Standard
Mounting
Style
Outlet Box
Mounting
Style
Use the three steps below to determine if your ceiling angle is greater than 34°
1
2
3
34°
PLACE
SLIDE
toward ceiling
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
Guide Touches
but NOT Ceiling
Wall
Use Standard Mounting
or Low-Profile Mounting
Use Angled Mounting
to hang the fan from a
to hang the fan from a flat ceiling.
vaulted or angled ceiling.
You need BOTH
a Longer
You need ONLY
a Longer
Downrod &
an Angled
Downrod
Mounting Kit
*most common
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Ceiling Bracket
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
to support structure with
(provided with outlet
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
If you are unable to do this,
call Technical Support at
1-888-227-2178.
still attached.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Refer to warning w.1 on pg. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Downrod
Standard
skip to next page
Downrod
for ceilings 8-10’ high
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
1
2
3
4
5
Shorter
Downrod
for fans installed
close to ceiling
10
9
8
7
6
Steps 6-10 to reassemble with new pipe
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
8”
3/8”
If the setscrew is not tightened
securely, the fan may fall.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Lower the adapter cover over
the downrod until it rests flush
against the motor housing. Align
the screw holes on the adapter
cover with the screw holes on
the motor housing and install the
three adapter cover screws found
Put the wires and downrod
through the canopy. Let the
canopy sit loosely on top of
the fan.
DO NOT PICK THE FAN UP BY
THE CANOPY OR WIRES. Place
the downrod ball into the slot
in the ceiling bracket.
in the
hardware bag.
Note: e adapter cover is not
used for low-profile mounting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Wiring
Note: To connect the wires, hold
the bare metal leads together and
place a wire connector over them,
then twist clockwise until tight.
C
Receiver
Using an orange wire connector
from the hardware bag:
Connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and ceiling bracket.
green/yellow stripe
Place the receiver on top of the downrod
assembly as shown.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Wiring (continued)
C
Using the orange wire connectors
from the remote control hardware bag:
Using the orange wire connectors
from the hardware bag:
•
Connect the yellow wire from
the receiver to the black wire
from the fan.
•
Connect the black (ungrounded)
wire from the ceiling to the black
wire from the receiver.
white
•
Connect the blue wire from the
receiver to the blue wire (or
possibly black with white stripe
wire) from the fan.
•
Connect the white (grounded)
wire from the ceiling to both the
white wire from the receiver and
the white wire from the fan.
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Wall Control
Screw
Cut-Out
Drywall
Drill Holes
Before
Drywall
Anchors
Painter’s
Tape
Cover Plate
Template
Template
Template
After
1. Tape the provided wall control
template with painter’s tape at
the desired installation area.
2. Drill holes inside the four
corners of the template.
Note: Make sure the wall
control template is level before
proceeding to the next step.
1. Using a 9/64 drill bit, drill a hole
in each screw cut-out on the wall
control template.
2. Using a hammer, tap a drywall
anchor found in the wall control
hardware bag into each hole
until the drywall anchor is flush
with the wall.
1. Using a drywall punch saw,
cut out the interior shape of
the template using one of
the four drilled corners as a
starting point.
2. Remove the template and the
cut-out section of drywall.
1. Insert the wall control into the
dry wall cut out.
2. Align the screw holes in the wall
control with the drywall anchors.
3. Install the cover plate using
a Phillips Head screwdriver
to secure the two cover plate
screws found in the wall control
hardware bag through the wall
control and into the drywall
anchors.
If you are using a outlet box for wall control installation, the wires coming from the wall
control must be grounded using the attached green wire. If not placed in an outlet box, cap
the green wire coming from the wall control with an included wire nut.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Blades
Insert a blade into the motor housing as shown.
Attach each blade to the fan using two
blade grommets, found in the hardware
bag, and two blade assembly screws, found
in the hardware bag.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Light Kit
Light Kit
Assembly
Screw
Align the screw holes and attach the
light kit assembly to the light kit fitter
using the three light kit assembly
Align the screw holes in the light kit
fitter with the screw holes in the fan’s
mounting plate. Attach the light kit
fitter to the mounting plate using the
three light kit fitter screws, found in
Using the ceramic wire connectors, connect
the blue wire from the fan to the black wire
from the light kit assembly. Connect the
white wire from the fan to the white wire
from the light kit assembly.
screws, found in the
hardware bag.
the
hardware bag.
Note: Be sure to use the CERAMIC wire
connectors to avoid fire hazard.
Make sure the light kit fitter and light kit assembly are securely
attached. Failure to properly secure all assembly screws could
result in the light kit fixture falling.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Light Kit (continued)
Tab
Clip
Bulb
Notch
To install the halogen bulb, angle
one end of the bulb into the
socket as shown, then push the
other socket inward and lift the
bulb up until it fits into place.
To install the bulb shield, raise
the bulb shield to the light kit
assembly and push the clips
onto the sockets.
Align the the notches in the
globe assembly with the tabs in
the light kit fitter. Carefully lift
the globe assembly as far as it
will go, then rotate it counter-
clockwise until it is held into
place by the three tabs.
See next page for fan
operation instructions.
When installing a halogen bulb, carefully cut off
the end of the plastic sleeve packaging and hold the
bulb by the plastic sleeve to screw it into the socket.
Note: In compliance with US federal energy regulations, this ceiling
fan contains a device that restricts its light output. Exceeding the
wattage limit marked on the MAX wattage sticker affixed to the
light socket(s) may result in fire hazard or improper operation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Operation
Battery
Battery
Holder
ON
Battery
Door
Before operating the wall control, press on the
battery door to eject it. Unscrew the battery
holder. Insert the battery, found in the control
hardware bag, with the positive (+) side facing
downward. Reinstall the battery holder and
reinsert the battery door into the wall control.
The remote transmitter is already paired
to the receiver and ready to use.
Note: If you would like to operate
multiple fans or multiple remotes,
or if your remote is not working,
please see the Troubleshooting
section at the end of this manual.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Operation (continued)
Reverse
Button
The Safe-Exit Program gives
you about thirty seconds of
light when you turn the lights
off to exit the room before the
(Low)
Fan
Speed
(a)
Fan
Speed
lights go out.To use Safe-Exit:
• Press the fan power button
off for at least three seconds to
initiate the Safe-Exit Mode.
(High)
• The lights will flash for visual
confirmation.
Lights
Down
Lights
Up
• The lights will stay on 50%
brightness for 20 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
(b)
Reverse
Fan
Note: For CFL lighting, the lights
will stay on 100% brightness
for 30 seconds. After a total of
30 seconds, the lights will be
completely off.
Power
Battery
Holder
Quickly press the up or down arrow to turn the lights off
and on. Hold the up or down arrow to raise or dim the light
level. The reverse button changes the direction that the
blades turn. The power button turns the fan off and on.
The reverse button on the wall
control changes the air flow
pattern. In warm weather, use
(a) downward air flow pattern.
In cold weather, use (b) upward
air flow pattern.
Dimming Mode: To enable dimming, you must first set
your remote to Dimming Mode. To toggle Dimming
Mode on or off, hold down the Fan Power button while
pressing the Light Down arrow twice.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Maintenance & Cleaning
OFF
Be sure to turn off
power to the fan
before performing
any maintenance or
relamping.
Changing the bulb - carefully rotate the
globe assembly clockwise and lower it from
the light kit. Remove the bulb shield. Press
in on the light socket to slide one end of the
bulb out and remove the bulb. Install a new
halogen bulb of the same type and wattage
and reinstall the globe assembly.
Cleaning the fan - use soft brushes or cloths
to prevent scratching. Cleaning products may
damage the finishes.
When installing a halogen bulb, carefully cut off
the end of the plastic sleeve packaging and hold the
bulb by the plastic sleeve to screw it into the socket.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Troubleshooting
Remote does not work
Fan doesn’t work
Excessive wobbling
• Make sure the battery is installed
correctly.
• Press a fan speed button (1-4).
• Tighten all of the blade screws
until they are snug.
AUTHORIZED SERVICE
CENTERS
For the most updated list of
Casablanca Authorized Service
Centers, visit
• Check the circuit breaker to
ensure the power is turned on.
• Install a new battery.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• If the remote still does not
work, you may need to pair
your remote. To prevent faulty
operation, please disconnect
power (at the wall switch,
• Check the wall control battery.
• Make sure the blades spin freely.
call toll free 1-888-227-2178.
• Use the provided balancing
kit and instructions to balance
the fan.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on pages 9-10.
breaker, or fan) from all other
ceiling fans within range while
pairing. To pair: cycle power
to the fan by turning power off
and back on at the wall switch
(or circuit breaker if necessary).
Within three minutes, press and
hold both the Fan Off button and
the 4 button for four seconds to
pair the remote. If applicable, the
fan will turn on and the lights
will flash and stay on to indicate
successful pairing.
Lights will not dim
• To enable dimming, you
must first set your remote to
Dimming Mode. To toggle
Dimming Mode on or off, hold
down the Fan Power button
while pressing the Light Down
arrow twice.
Noisy Operation
• Check the wire connection in
the light kit assembly.
• Tighten the blade screws until
they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Ensure each bulb you are using
supports dimming.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Troubleshooting (continued)
Installing Multiple Fans with Independently Operating Remote Controls
Installing One Fan Operating on Multiple Remote Controls
To install multiple fans with independently operating remote controls, there is no need to
perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply
install each receiver into a fan and use the appropriate transmitter to operate each fan.
To have multiple remote controls operate one fan, you must pair each additional transmitter
to the receiver in the fan. The transmitter that shipped with your fan is already paired.
Note: To prevent faulty operation, please disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while pairing.
If your remote is not working, see the “Remote does not work” section on the previous page.
For each additional transmitter, cycle power to the fan by turning power off and back on at
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
Installing Multiple Fans Operating on a Single Remote Control
“Unpairing” Procedure for Faulty Operation of Remote Controls
X
To have multiple fans operated by a single remote control, you must pair the transmitter to each
additional receiver. The receiver that shipped with your fan is already paired to the transmitter.
If a transmitter is mistakenly operating a fan, you need to “unpair” the transmitter from that
fan’s receiver. The “unpairing” procedure is the same as the pairing procedure.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while pairing each fan.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while “unpairing” a fan.
For each additional fan, ensure that a compatible receiver is installed. Disconnect power from all
other fans while pairing. To pair: cycle power to the fan by turning power off and back on at
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
Disconnect power from all other fans while “unpairing.” Then, cycle power to the fan you
wish to “unpair” by turning power off and back on at the wall switch (or circuit breaker
if necessary). Within three minutes, press and hold both the Fan Off button and the 4
button for four seconds to “unpair” the remote. If applicable, the fan will turn off and the
lights will flash and turn off to indicate successful “unpairing.”
20
Download from Www.Somanuals.com. All Manuals Search And Download.
M8511-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
|