1.888.227.2178
Table of Contents
What to Expect with
Your Installation
Tools Needed
Ceiling Plate
Hanging the Fan
Congratulations on purchasing your new Casablanca®
ceiling fan! It will provide comfort and performance
in your home or office for many years. This installation
and operation manual contains complete instructions
for installing and operating your fan.
30 inches
2
3
7
4
8
5
We are proud of our work and appreciate the
opportunity to supply you with the best ceiling fan
available anywhere in the world.
Wiring
Wall Control
Canopy
Blades
To register your fan, please visit:
Save your receipt for proof of purchase.
6
10
Maintenance
& Cleaning
Light Kit
Operation
Troubleshooting
?
?
?
11
12
14
15
1
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Tools Needed
Screwdriver
(included)
Wire Strippers
Ladder
9/64” Drill
Bit (optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Ceiling Plate
Bumper
OFF
Use wood screws
Use machine screws
(included) when securing (provided with outlet
to support structure with box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes outlet box. Make sure
in support structure to aid it is securely installed
in securing ceiling plate and is acceptable for fan
Make sure all four bumpers are
with hardware found in
support of 31.8 kg (70
lbs) or less.
still attached.
the
hardware bag.
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
Refer to warning w.1 on pg. 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Hanging the Fan
Unlock the canopy cover from the canopy
ring tabs to loosen the canopy ring and
lower it down to the fan body as shown.
DO NOT PICK THE FAN UP BY THE
WIRES. Use the hanging hole on the
body of the fan to hang the fan on the
hook of the ceiling mounting plate.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Wiring
Note: To connect the wires, hold
the bare metal leads together and
place a wire connector over them,
then twist clockwise until tight.
C
C
Using an orange wire connector
from the hardware bag:
Using an orange wire connector:
•
Connect the black (ungrounded)
Connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and ceiling bracket.
wire from the ceiling to the black
wire from the fan/receiver.
•
Connect the white (grounded)
wire from the ceiling to the white
wire from the fan/receiver.
green
L
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Wall Control
Screw
Cut-Out
Drywall
Drill Holes
Before
Drywall
Anchors
Painter’s
Tape
Cover Plate
Template
Template
Template
After
1. Tape the provided wall control
template with painter’s tape at
the desired installation area.
2. Drill holes inside the four
corners of the template.
Note: Make sure the wall
control template is level before
proceeding to the next step.
1. Using a 9/64 drill bit, drill a hole
in each screw cut-out on the wall
control template.
2. Using a hammer, tap a drywall
anchor found in the wall control
hardware bag into each hole
until the drywall anchor is flush
with the wall.
1. Using a drywall punch saw,
cut out the interior shape of
the template using one of
the four drilled corners as a
starting point.
2. Remove the template and the
cut-out section of drywall.
1. Insert the wall control into the
dry wall cut out.
2. Align the screw holes in the wall
control with the drywall anchors.
3. Install the cover plate using
a Phillips Head screwdriver
to secure the two cover plate
screws found in the wall control
hardware bag through the wall
control and into the drywall
anchors.
If you are using a outlet box for wall control installation, the wires coming from the wall
control must be grounded using the attached green wire. If not placed in an outlet box, cap
the green wire coming from the wall control with an included wire nut.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Canopy
Canopy Screw
Hanging Slot
Partially install two of the canopy screws,
found in the hardware bag, into screw
holes on opposite corners of the ceiling
plate as shown. Choose the two screw holes
that are aligned with the hanging slots in
the fan body.
Using both hands, lift the fan body from the
hook and align the hanging slots on both sides
of the fan body with the two partially installed
canopy screws. Slide the two slots on both
sides of the fan body between the head of the
screws and rotate the fan body clockwise so the
screws hold the fan body firmly in place.
Install the remaining two canopy screws,
found in the hardware bag, by holding
the fan body cover to the ceiling mounting
plate. Tighten all four screws securely.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Canopy (continued)
Canopy
Tab
Holders
Canopy
Ring
Tabs
Before going to the next step, locate
the two sets of canopy ring tabs that
are on the top edge of the canopy
and the two sets of canopy tab
holders found at the top of the fan
body near the ceiling.
To install the canopy ring, lift the
canopy, then rotate clockwise until
the tabs are held in place by the
tab holders, locking the canopy
ring into place.
To check your work, make sure
there is an even gap all the way
around between the ceiling and
the canopy ring.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Blades
Slide a blade into a slot located on the blade ring.
Install the blade using three blade screws
and washers, found in the hardware bag.
Repeat this process for all five blades.
Note: The blades will only fit properly over the
screws holes one way. If the holes do not line up,
remove the blade and turn it over.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Light Kit
Tab
Notch
Install a halogen bulb into each
Align the notches in the globe
assembly with the tabs on the
light kit.
Carefully lift the globe assembly
up as far as it will go and rotate
counterclockwise until the globe
is held securely by the three tabs.
light socket. When necessary,
replace with bulbs of the same
type and wattage.
See next page for fan
operation instructions.
When installing a halogen bulb, carefully cut off
the end of the plastic sleeve packaging and hold the
bulb by the plastic sleeve to screw it into the socket.
Note: In compliance with US federal energy regulations, this ceiling
fan contains a device that restricts its light output. Exceeding the
wattage limit marked on the MAX wattage sticker affixed to the
light socket(s) may result in fire hazard or improper operation.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Operation
Battery
Battery
Holder
ON
Battery
Door
Before operating the wall control, press on the
battery door to eject it. Unscrew the battery
holder. Insert the battery, found in the control
hardware bag, with the positive (+) side facing
downward. Reinstall the battery holder and
reinsert the battery door into the wall control.
The remote transmitter is already paired
to the receiver and ready to use.
Note: If you would like to operate
multiple fans or multiple remotes,
or if your remote is not working,
please see the Troubleshooting
section at the end of this manual.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Operation (continued)
Reverse
Button
The Safe-Exit Program gives
you about thirty seconds of
light when you turn the lights
off to exit the room before the
(Low)
Fan
Speed
(a)
Fan
Speed
lights go out.To use Safe-Exit:
• Press the fan power button
off for at least three seconds to
initiate the Safe-Exit Mode.
(High)
• The lights will flash for visual
confirmation.
Lights
Down
Lights
Up
• The lights will stay on 50%
brightness for 20 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
(b)
Reverse
Fan
Note: For CFL lighting, the lights
will stay on 100% brightness
for 30 seconds. After a total of
30 seconds, the lights will be
completely off.
Power
Battery
Holder
Quickly press the up or down arrow
to turn the lights off and on. Hold
the up or down arrow to raise or
dim the light level. The reverse
button changes the direction that
the blades turn. The power button
turns the fan off and on.
The reverse button on the wall
control changes the air flow
pattern. In warm weather, use
(a) downward air flow pattern.
In cold weather, use (b) upward
air flow pattern.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Maintenance & Cleaning
OFF
Be sure to turn off
power to the fan
before performing
any maintenance or
relamping.
Changing the bulbs - carefully remove the
globe assembly by lifting and rotating clockwise.
Replace with bulbs of the same type and
wattage. Reinstall the globe assembly.
Cleaning the fan - use soft brushes or cloths
to prevent scratching. Cleaning products may
damage the finishes.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Troubleshooting
Remote does not work
Excessive wobbling
Fan doesn’t work
AUTHORIZED SERVICE
• Make sure the battery is installed
correctly.
• Tighten all of the blade
screws until they are snug.
• Press a fan speed button (1-4).
CENTERS
For the most updated list of
Casablanca Authorized Service
Centers, visit
• Check the wall control battery.
• Install a new battery.
• Use the provided balancing
kit and instructions to balance
the fan.
• Check the circuit breaker to
ensure the power is turned on.
• If the remote still does not
work, you may need to pair
your remote. To prevent faulty
operation, please disconnect
power (at the wall switch,
call toll free 1-888-227-2178.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then check all the
connections according to the
wiring diagram on page 6.
breaker, or fan) from all other
ceiling fans within range while
pairing. To pair: cycle power
to the fan by turning power off
and back on at the wall switch
(or circuit breaker if necessary).
Within three minutes, press and
hold both the Fan Off button and
the 4 button for four seconds to
pair the remote. If applicable, the
fan will turn on and the lights
will flash and stay on to indicate
successful pairing.
Lights dim when turned on or
do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the
light sockets (see page 14 for
instructions on changing the
bulbs).
Noisy Operation
• Tighten the blade screws until
they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Troubleshooting (continued)
Installing Multiple Fans with Independently Operating Remote Controls
Installing One Fan Operating on Multiple Remote Controls
To install multiple fans with independently operating remote controls, there is no need to
perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply
install each receiver into a fan and use the appropriate transmitter to operate each fan.
To have multiple remote controls operate one fan, you must pair each additional transmitter
to the receiver in the fan. The transmitter that shipped with your fan is already paired.
Note: To prevent faulty operation, please disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while pairing.
If your remote is not working, see the “Remote does not work” section on the previous page.
For each additional transmitter, cycle power to the fan by turning power off and back on at
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
Installing Multiple Fans Operating on a Single Remote Control
“Unpairing” Procedure for Faulty Operation of Remote Controls
X
To have multiple fans operated by a single remote control, you must pair the transmitter to each
additional receiver. The receiver that shipped with your fan is already paired to the transmitter.
If a transmitter is mistakenly operating a fan, you need to “unpair” the transmitter from that
fan’s receiver. The “unpairing” procedure is the same as the pairing procedure.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while pairing each fan.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while “unpairing” a fan.
For each additional fan, ensure that a compatible receiver is installed. Disconnect power from all
other fans while pairing. To pair: cycle power to the fan by turning power off and back on at
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
Disconnect power from all other fans while “unpairing.” Then, cycle power to the fan you
wish to “unpair” by turning power off and back on at the wall switch (or circuit breaker
if necessary). Within three minutes, press and hold both the Fan Off button and the 4
button for four seconds to “unpair” the remote. If applicable, the fan will turn off and the
lights will flash and turn off to indicate successful “unpairing.”
16
Download from Www.Somanuals.com. All Manuals Search And Download.
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
|