1.888.227.2178
Table of Contents
What to Expect with
Your Installation
Ceiling Bracket
Installation
Tools Needed
Mounting Options
Congratulations on purchasing
your new Casablanca® ceiling
fan! It will provide comfort and
performance in your home or office
for many years. This installation
and operation manual contains
complete instructions for installing
and operating your fan.
30 inches
7 feet
Ladder
4
2
3
7
5
Preparation
Downrod
Wiring
Canopy
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan please visit:
6
10
11
Maintenance
& Cleaning
Blades
Switch Housing
Troubleshooting
?
?
ON
?
12
13
15
16
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Tools Needed
Pliers
Wire Strippers
Screwdrivers
Ladder
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
O
34
CEILING
1.888.227.2178
Mounting Options
If you have a flat ceiling:
Hang your fan by a standard downrod (included).
Standard
Mounting
Support
Structure
Support
Structure
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
1. You will need a longer downrod (sold separately).
Angled
Mounting
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Ceiling
Angled
(required)
Standard
Mounting
Style
Outlet Box
Mounting
Style
Use the three steps below to determine if your ceiling angle is greater than 34°
1
2
3
34°
PLACE
SLIDE
toward ceiling
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
Guide Touches
but NOT Ceiling
Wall
Use Standard Mounting
or Low-Profile Mounting
Use Angled Mounting
to hang the fan from a
to hang the fan from a flat ceiling.
vaulted or angled ceiling.
You need BOTH
a Longer
You need ONLY
a Longer
Downrod &
an Angled
Downrod
Mounting Kit
*most common
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Ceiling Bracket Installation
For angled ceilings, point
opening toward peak.
OFF
Use wood screws
(included) when securing
to support structure with
Use machine screws
(provided with outlet
box) when securing to
Make sure all four (4) bumpers
are still attached.
If you are unable to do this,
call Technical Support at
1-888-227-2178.
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
in support structure to aid
outlet box. Make sure
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Refer to warning w.1 on pg. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Preparation
Ceiling Bracket Installation (continued)
Time Saver Tip: Get a helper
to insert grommets, found in
the
hardware bag, into the
Remove the shipping blocks from
the motor. Save the five screws.
They will be needed for blade iron
installation.
blades while you’re doing the
next couple of steps.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Downrod
Standard
skip to next page
Downrod
for ceilings 8-10’ high
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
1
2
3
4
5
Shorter
Downrod
for fans installed
close to ceiling
10
9
8
7
6
Steps 6-10 to reassemble with new pipe
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
8”
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Wiring
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
Using orange wire
connectors from
green/yellow stripe
Using an orange wire
connector from
the
hardware bag,
connect the black wire
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
(ungrounded) from the
ceiling to the black and
the blue wires from the
fan. Connect the white
wire (grounded) from
the ceiling to the white
wire from the fan.
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Insert the two canopy screws
Lift the canopy into place so that
the screw holes are aligned.
found in the
hardware bag.
Note: Fan style may vary.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Blades
Remember the screws that
you kept after removing the
shipping blocks (page 6)? You
need them plus five more from
hardware bag for this step.
Insert grommets found in the
hardware
Lightly attach the blade irons to the
motor with screws found in
bag into the holes in the blades, then
secure each blade to a blade iron with
the
hardware bag, then securely
screws found in the
hardware bag.
tighten after both screws are attached.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Switch Housing
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Insert the third screw, found in
hardware bag, into place and then
tighten all three (3) screws.
Screw two (2) housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
the
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Switch Housing (continued)
Connect the fandangle to the short chain
coming from the switch housing.
Lift the lower switch housing up until the
holes line up with the screw holes in the
upper switch housing. Install the three (3)
switch housing screws, found in
Connect the plugs from the upper and
lower switch housings. Make sure to
line up the colored markings on the
connectors.
the
hardware bag.
Make sure the lower switch housing is securely attached to the
upper switch housing. Failure to properly secure all 3 assembly
screws could result in the switch housing fixture falling.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Switch Housing (continued)
Maintenance & Cleaning
ON
The pull chain controls the
fan: high, medium, low,
extra low, and off.
To switch the direction of air
For cleaning the fan, use soft
flow, move the reverse switch
to the opposite position.
In warm weather, use
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
downward air flow pattern.
In cold weather, use upward
air flow pattern.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
1.888.227.2178
Troubleshooting
Fan doesn’t work
Noisy Operation
Excessive wobbling
• Pull the pull chain to make sure
it is on.
• Tighten the blade and blade
iron screws until they are snug.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Check the circuit breaker to
ensure the power is turned on.
• Use the provided balancing
kit and instructions to balance
the fan.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 10.
• Check the plug connection in
the switch housing.
AUTHORIZED SERVICE CENTERS
For the most updated listing of Casablanca Authorized
call toll free 1-888-227-2178.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 08/08/12 • © Casablanca Fan Company
|