Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1) Read the information for use (user manual).
10) The amplifier may only be used in accordance with the information provided
in the user manual. Before and during the usage of the amplifier please ensure
that all recommendations, especially the safety recommendations as detailed in
the user manual, are adhered to.
2) Please keep this user manual in a safe place during the lifetime of the am-
plifier. The user manual forms an integral part of the amplifier. Reselling of the
amplifier is only possible if the user manual is available. Any changes made to
the amplifier have to be documented in writing and passed on to the buyer in
the event of resale.
The VORTEX-Amplifier is designed for the amplification of pulsed audio signals
and the amplifier should only be connected to speakers with an average
impedance that is not lower than the impedances specified in points 3.9.2, 3.9.3
and 3.9.4.
3) Heed all warnings.
11) Do not place this amplifier on an unstable cart, stand,
tripod, bracket, or table. The device may fall, causing
serious injury, and serious damage to the device itself.
4) Follow all instructions.
5)Do not use this amplifier near water (for example, in damp rooms or near a
swimming pool). Do not place any object filled with liquids, such a vase, on the
amplifier.
12) The amplifier can only be disconnected from the power supply by removing
the plug, which must be freely accessible at all times. Unplug this amplifier
during lightning storms or when unused for long periods of time.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the user
manual.
13) Refer all servicing to qualified service personnel.
Servicing is required when
the power-supply cord or plug has been damaged,
liquid has been spilled or objects have fallen into the amplifier,
the amplifier has been exposed to rain or moisture,
the amplifier has been dropped or suffered damage in any other way,
the amplifier exhibits a distinct change from its normal function or
performance.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus that produce heat.
9) Protect the power cord from being walked on, pinched or damaged in any
other way. Pay particular attention to plugs and the point where they exit from
the amplifier.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P. 2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Read the information for use (user manual)
CAUTION – HIGH VOLTAGE HAZARDS
EXIST WITHIN THIS PRODUCT.
REFER ALL SERVICING TO
When shipping the VORTEX amplifier, always use the original shipping carton
and packing materials. For maximum protection, repack the unit as it was origi-
nally packed at the factory.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AUTHORISED PERSONNEL.
2. Environments
THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL, IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF UNINSULATED DANGEROUS
VOLTAGE WITHIN THE PRODUCT’S ENCLOSURE.
Use this amplifier only in E1, E2, E3 or E4 environments according to EN55103-2
“Electromagnetic compatibility – Product family standard for audio, video and
audio-visual and entertainment lighting control apparatus for professional use
– Part 2: Immunity”
3.Ventilation
THE EXCLAMATION MARK IS INTENDED TO ALERT THE USER
TO IMPORTANT INSTRUCTIONS ALSO FOR MAINTENANCE IN THE
LITERATURE ACCOMPANYING THE AMPLIFIER.
Slots and openings in the cabinet are provided for ventilation, to ensure reliable
operation of the amplifier and to protect it from overheating. These openings
must not be blocked or covered. This amplifier should not be installed unless
proper ventilation is provided or manufacturer’s instructions have been
adhered to.
THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL ALERTS
THE USER TO DANGEROUSLY HIGH VOLTAGE AT THE SPEAKON
CONNECTORS THAT COULD POTENTIALLY BE LIFE THREATENING.
4.Water And Moisture
Do not use this amplifier near water (for example, in damp rooms or near a
swimming pool).
CAUTION – RISK OF ELECTRIC SHOCK – DO NOT OPEN.
5. Cleaning
Unplug this amplifier from the wall outlet before cleaning. Do not use liquid or
aerosol cleaners.
WARNING – TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
AMPLIFIER TO RAIN OR MOISTURE.
6. Power-cord Protection
THE AMPLIFIER MAY ONLY BE CONNECTED
TO A SOCKET WITH A CONNECTION TO GROUND.
Power-supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon them or against them, paying particular atten-
tion to cords and plugs, and the point where they exit from the amplifier.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P. 3
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Lightning
12. Damages that require service
For added protection of this amplifier during lightning storms, or when it is
left unattended and unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the amplifier due to lightning and power-
line surges. Disconnection from the mains power supply can only be achieved
by removing the plug from the mains socket and by external disconnecting all
poles from the mains.
Unplug this amplifier from the mains supply and refer to your dealer/distributor
or other authorised repair workshop if any of the following situations occur:
if liquid has been spilled, or objects have fallen into the amplifier
if the amplifier does not operate normally as described in the user manual.
Operate the controls only as described in the user manual.
if the amplifier has been dropped or damaged in any other way.
when the amplifier exhibits a distinct change from its normal function or
performance.
8. Interference of external objects and/or liquids with the appliance
Never push objects of any kind into this amplifier through openings as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the amplifier.
13. Servicing
Do not attempt to service this amplifier yourself.As opening or removing covers
may expose you to dangerous voltage or other hazards, the amplifier may only
be opened by qualified personnel. Please refer to your dealer/distributor.
9. Accessories
Do not place this amplifier on an unstable cart, stand, tripod, bracket, or table.
The amplifier may fall,causing serious injury,and serious damage to the product.
Any mounting of the amplifier should follow the manufacturers instructions,
and should use a mounting accessory recommended by the manufacturer.
14. Servicing and Replacement Parts
All service and repair work must be carried out by a CAMCO authorised dealer.
When replacement parts are required, please ensure that the dealer/distributor
only uses replacement parts specified by the manufacturer. The use of un-
authorized replacement parts may result in injury and/or damage through fire
or electric shock or other electricity-related hazards.
10. Connecting
When you connect the amplifier to other equipment, turn off the power and
unplug all of the equipment from the supply source. Failure to do so may cause
an electric shock and serious personal injury. Read the user manual of the other
equipment carefully and follow the instructions when making the connections.
15. Safety Check
Upon completion of any service or repairs to this product, ask the dealer/
distributor to perform safety checks to determine that the amplifier is in proper
operating condition.
11. Sound Volume
Reduce the volume to minimum before you turn on the amplifier to prevent
sudden high levels of noise which may cause hearing or speaker damage.
(See also 4.1.1 Volume control)
Recommendations on how to carry out the safety test can be found in
DIN VDE 0701-1“Maintenance, Modification and Test of Electronic Appliances“.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P. 4
Download from Www.Somanuals.com. All Manuals Search And Download.
EC Declaration of Conformity in accordance to EC Directives:
electro-magnetic compatibility (Council Directive 89/336/EEC,
as amended by Directives 92/31/EEC and 93/68/EEC);
low-voltage electrical equipment (Council Directive 73/23/EEC )
Manufacturers Name:
CAMCO Produktions- und Vertriebs-GmbH
für Beschallungs- und Beleuchtungsanlagen
Manufacturers Address:
Fischpicke 5, D-57482 Wenden, Germany
Declares that the product with the model name:
CAMCO Power amplifier VORTEX-6, VORTEX-4, VORTEX-2.6 and VORTEX-200V
Conforms to the following standards:
EN60065 Safety
EN55103-1 Emission
EN55103-2 Immunity
The operating conditions and application environments presupposed in the
information for use (user manual) are to be kept accordingly.
Please Note:The following formulations have been chosen:VORTEX-6,VORTEX-4,
VORTEX-2.6 and VORTEX-200V for the type plate and for the EC declaration of
conformity. VORTEX 6, VORTEX 4,VORTEX 2.6 and VORTEX 200V for the front
face of the appliance and for the text in the user manual.
Wenden, 25.04.2005
Joachim Stöcker
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P. 5
Download from Www.Somanuals.com. All Manuals Search And Download.
P. 2 IMPORTANT SAFETY INSTRUCTIONS
P. 3 EXPLANATION OF SYMBOLS / SAFETY
P. 5 EC DECLARATION OF CONFORMITY
P. 6 CONTENTS
4.1.4 Limiter Switch
P.25 6 TROUBLESHOOTING
6.1 On LED Flashing Sequences
4.2 Indicators
4.2.1 On LEDs (multifunctional)
4.2.2 Signal LEDs
P.26 6.2 Problem: No Sound
6.3 Problem: No Sound or Sound Is Too Low
6.4 Problem: No Channel Separation
6.5 Problem: Distorted Sound
P.27 6.6 Problem: Hiss
P. 1 8
P. 1 9
P. 7 1 WELCOME
4.2.3 Clip LEDs (multifunctional)
4.3 Power Amp Protection Systems
4.3.1 Clip Limiter
1.1 Welcome to CAMCO
1.2 Unpacking
P. 8 1.3 The Amplifier
P. 9 2 FACILITIES
4.3.2 Under Impedance Limiter
4.3.3 SOA Protection
6.7 Problem: Squeals and Feedback
P.28 7 SPECIFICATION
2.1 VORTEX – The Front
2.2 VORTEX – The Rear
P. 1 0 2.3 Factory Settings
P. 11 3 INSTALLATION
3.1 Mains Supply
4.3.4 Speaker Protect Limiter
4.3.5 DC Protection
P.30 8 MEASUREMENTS
P.34 9 WARRANTY INFORMATION
9.1 Summary Of Warranty
4.3.6 DC Servo
4.3.7 Over Current Protection
4.3.8 Thermal Protection
4.4 Mains Protections
9.2 Items Excluded From This Warranty
9.3 What CAMCO Will Do
3.2 On/Off Switch
9.4 How To Obtain Warranty Service
9.5 CAMCO’s Product Improvement
P.35 10 SERVICE INFORMATION
P.36 11 MAINTENANCE INFORMATION
12 DECOMISSIONING
3.3 Mounting
4.4.1 Inrush Current Limitation
4.4.2 Mains Over Voltage Detection
4.4.3 Mains Failure Detection
4.4.4 Fuse Protection
P. 1 3 3.4 Cooling
3.5 Ground Lift
P. 2 0
3.6 Optional Feature
3.7 Mode Indicators
4.5 Main SMPS Protections
4.5.1 Over Current Protection
4.5.2 Thermal Protection
4.6 Fans
P.37 COMPANY INFORMATION
P. 1 4 3.8 Mode Selector
3.9 Wiring
3.9.1 E.U.I. and XLR Connection
3.9.2 Stereo Operation
3.9.3 Parallel-Mono Operation
3.9.4 Mono-Bridge Operation
3.9.5 SPEAKON Connection
P. 1 6 4 OPERATION
P. 2 1 4.7 Filter Cleaning
P. 2 2 5 OPTIONS
5.1 E.U.I.2(Extended User Interface)
5.1.1 What Are The Possibilities
Using The E.U.I.2?
4.1 Controls
5.2 CAI (CAMCO Audio Interface)
5.2.1 Wiring
4.1.1 Volume Control
P. 1 7
4.1.2 Gain Selector
P. 2 3
P. 2 4
5.2.2 CAI Address Settings
5.2.3 CAI Status Indicator
4.1.3 Gain and Input Sensitivity
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P. 6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Welcome to CAMCO
1.2 Unpacking
Established in 1983,CAMCO has gained worldwide experience with professional
sound reinforcement technology. Within the audio market, CAMCO specialises
in the production and marketing of high quality power amplifiers and sound
systems for use both on tour and in static installations.
Please unpack and inspect your new amplifier for any damage that may have
occurred during transit. If damage is found, notify the transportation company
immediately. Only you the consignee may initiate a claim for shipping damage.
CAMCO will be happy to cooperate fully as needed. Please save the shipping
carton as evidence of damage for the shipper’s inspection.
The success of the LA, DL and DX series power amps has made the CAMCO
name synonymous with professional quality, high performance and utterly
reliable power amps.
Even if the amplifier has arrived in perfect condition, save all packing materials
so you will have them if you ever need to transport the unit.
CAMCO’s commitment to research and development, seen not just in the area
of materials and technology but also most importantly in its highly skilled and
motivated workforce, is one of the keys to its ongoing success.
NEVER SHIP THE AMPLIFIER WITHOUT THE ORIGINAL
PACKING MATERIALS.
When shipping the VORTEX amplifier, always use the original shipping carton
and packing materials. For maximum protection, repack the unit as it was origi-
nally packed at the factory.
With its all-new VORTEX power amp series, CAMCO is pioneering a new dimen-
sion in professional power amp construction. The seamless combination of
ground-breaking technology with proven safety elements is the hallmark of
the new series.
Welcome to the new world of professional power amplifiers –
WELCOME TO CAMCO!
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P. 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 The Amplifier
The VORTEX also uses a microprocessor for controlling and monitoring the
power amp. This has four main advantages over more traditional power amp
systems:
The VORTEX is a Class-H power amplifier with a power output of:
VORTEX 200V 3,2 kW per channel @ 4 Ω
6,4 kW in Mono-Bridge @ 8 Ω
Reduced Distortion
Improved Noise Characteristics
6,4 kW in Parallel-Mono @ 2 Ω
Integrated Remote Control
VORTEX 6
VORTEX 4
VORTEX 2.6
3 kW per channel @ 2 Ω
Indication of Protection or Failures by different LED sequences
6 kW in Mono-Bridge @ 4 Ω
6 kW in Parallel-Mono @ 1 Ω
2 kW per channel @ 2 Ω
4 kW in Mono-Bridge @ 4 Ω
4 kW in Parallel-Mono @ 1 Ω
1,3 kW per channel @ 2 Ω
2,6 kW in Mono-Bridge @ 4 Ω
2,6 kW in Parallel-Mono @ 1 Ω
The VORTEX has been designed as an intelligent and powerful amplifier
for performing specialised tasks within a complex audio system. Users can
adapt the power amp to meet their specific audio requirements before use.
Controls mounted on the front and the rear of the VORTEX allow the different
functions to be accessed.
Since some of the externally mounted controls have multiple functions, it is
important that users should familiarise themselves thoroughly with the entire
range of controls and programmable features before using the power amp.
VORTEX power amplifiers are fitted with Switched Mode Power Supplies (SMPS),
which significantly reduces the weight and size (only 2U) of the amplifier. Using
SMPS, the 3 symmetrical supply voltages (2 symmetrical supply voltages for
VORTEX 2.6) of the power amplifier are more stable than the power supplies
used in conventional amplifiers.
If you have any questions regarding features and/or functions of your VORTEX,
CAMCO will be pleased to offer you further information. Alternatively, contact
your dealer or distributor.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P. 8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
10 11
1
2
3
4
5
6
7
8
2.1 VORTEX – The Front
1 On/Off Switch
2.2 VORTEX – The Rear
18 Mode Selector
7 Removable Air Filter System
8 Cooling Air Inlet Vents
12 AC Power Cable
19 Limiter Switch
2 Volume Control – Channel A
3 Volume Control – Channel B
4 On LEDs (multifunctional)
5 Signal LEDs
13 CAMCO Audio Interface (CAI)
14 SPEAKON Outlets
20 Gain Selector
9 Enter-Switch (behind Front Panel)
21 Extended User Interface (E.U.I.)
22 XLR – Line Links
23 XLR – Line Inputs
24 Rating Plate
10 Operating Mode LEDs
11 CAI Status LED
15 Cooling Air Outlet Vents
16 Input Ground Lift Switch
17 Optional Feature Selector
6 Clip LEDs (multifunctional)
24
16
17
18
19
20
13
MODEL:
OUTPUT PWR PER CH/IMP:
SER. NO.:
MADE IN GERMANY
12
14
15
23
22
21
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P. 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Factory settings
VORTEX amplifiers are delivered with the following factory settings
Front panel:
Rear panel
Input Ground Lift
Optional Feature
Mode
Grounded
Circle
On/Off Switch
Off
Amplifier is switched off
Stereo
SpP
Limiter
Gain
26 dB
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.10
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Mains supply
NOTE: Even under normal conditions the mains current can reach levels up
to 60 A (230 V), 120 A (120 V) and 140 A (100 V), respectively; this could
cause lamps to flicker if connected to the same mains as the amp. The im-
pedance of the AC circuit should be less than 0,157 Ohms to avoid flicker
according to EN61000-3-11 “Electromagnetic compatibility – Part 3-11:
Limits – Limitation of voltage changes, voltage fluctuations and flicker in
the public low-voltage supply systems – Equipment with rated current
≤ 75 A and subject to conditional connection”.
When mounting or connecting the amp always disconnect it from mains.
Only connect the VORTEX amplifier to an appropriate AC circuit and outlet,
according to the requirements indicated in the second line on the rating
plate.
MODEL:
MODEL:
VORTEX-200 V
VORTEX-6
230 V ~ 50/60 Hz 12 A 1700 W
OUTPUT PWR PER CH/IMP:
230 V ~ 50/60 Hz 12 A 1800 W
OUTPUT PWR PER CH/IMP:
3200 W / 4 Ohm
3000 W / 2 Ohm
If in any doubt, consult your local power provider. Never attempt to mea-
sure this impedance level with your ohmmeter.This may damage your me-
ter and expose you to the risk of electric shock!
SER. NO.:
xxxxxxx
MADE IN GERMANY
SER. NO.:
xxxxxxx
MADE IN GERMANY
MODEL:
MODEL:
VORTEX-4
VORTEX-2.6
230 V ~ 50/60 Hz 10 A 1450 W
OUTPUT PWR PER CH/IMP:
230 V ~ 50/60 Hz 7,2 A 1005 W
OUTPUT PWR PER CH/IMP:
1500 W / 1,8 Ohm
2000 W / 2 Ohm
SER. NO.:
xxxxxxx
MADE IN GERMANY
SER. NO.:
xxxxxxx
MADE IN GERMANY
3.2 On/Off Switch
NOTE:This switch does NOT disconnect the amplifier from mains.
The switch initiates start-up by activating the current limiting function. As soon
as the power amplifier is connected to the mains power supply, a voltage is
supplied to both the line-filter and the fused input of the controllable rectifier.
Disconnecting the amplifier from the main power supply can only be achieved
by physically separating the amplifier from the mains by pulling the mains plug.
The mains plug therefore has to be freely accessible. Disconnect the mains plug
from the mains during a lightning storm or when the amplifier remains unused
or un-supervised for a prolonged period of time. Alternatively, you can discon-
nect the amplifier via an external all-pole disconnection from the mains.
Exemplary rating plates for a mains supply of 230 V AC 50/60 Hz.
Power Supply Data:
Voltage Mains Frequency Current Power Consumption
VORTEX-200V 120 V
VORTEX-200V 220 V
VORTEX-200V 230 V
50/60 Hz
60 Hz
24 A
12 A
12 A
28 A
24 A
12 A
12 A
24 A
20 A
10 A
10 A
14,4 A
7,2 A
7,2 A
1700 W
1700 W
1700 W
1800 W
1800 W
1800 W
1800 W
1450 W
1450 W
1450 W
1450 W
1005 W
1005 W
1005 W
50/60 Hz
50/60 Hz
50/60 Hz
60 Hz
VORTEX-6
VORTEX-6
VORTEX-6
VORTEX-6
VORTEX-4
VORTEX-4
VORTEX-4
VORTEX-4
VORTEX-2.6
VORTEX-2.6
VORTEX-2.6
100 V
120 V
220 V
230 V
100 V
120 V
220 V
230 V
120 V
220 V
230 V
50/60 Hz
50/60 Hz
50/60 Hz
60 Hz
If a power cut occurs while the amplifier is switched on, it will restart auto-
matically once the power supply has been restored. All settings prior to the loss
of power will be maintained.
50/60 Hz
50/60 Hz
60 Hz
50/60 Hz
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.11
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Mounting
Use four screws and washers when mounting the amplifier to the front rack rails.
For mobile use, the amplifier should also be secured using the 19” mounting
elements on the rear panel.
10,5 mm
Amplifier switched off
465,0 mm
76,2 mm
442,0 mm
Amplifier switched on (On LED is lighting up)
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.12
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 Cooling
3.6 Optional Feature
Under normal operation of the power amp, overheating should never be a
problem. The air is taken in from the front and out through the back. It is of
course essential that while the power amp is running air is able to circulate
around it freely.
Could be activated with future released software versions.
The efficiency of the cooling will depend on the immediate environment (e.g.
an enclosed rack, direct sunlight) and on whether the front filter is clogged. If
the amp is installed in a case, the open area at the back of the case must be at
least 140 cm². This area should be in line with the amp.
If this can not be achived a forced ventilation system has to be used.
3.7 Mode Indicators
On the front panel there are two yellow LEDs to indicate the mode that is set.
In stereo mode none of them will be lit. In Parallel-Mono the (PM) LED will be lit
and in Mono-Bridge, the (MB) LED will be lit.
3.5 Ground Lift
The input signal ground (pin 1 for all 4 XLRs) is connected to the ground of the
mains supply. In order to avoid ground loops, this connection can be separated
via a resistor. The ground potential of the power amp and the ground of the
loudspeaker always remain connected to the ground of the mains supply
regardless of the setting of this switch.
Amplifier in Parallel-Mono mode
Amplifier in Mono-Bridge mode
to Pin 1
of the XLRs
Removing or taping the mains connector ground is illegal and dangerous.
DO NOT REMOVE MAINS CONNECTOR GROUND
IT IS ILLEGAL AND DANGEROUS
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.13
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 Mode Selector
3.9.2 Stereo Operation
The switch on the rear panel changes the operating mode. Moving this switch
will shutdown the amplifier and restart it in the new operating mode.
Two fully independent amplifier channels (normal operating mode).
VORTEX
Z ≥ *Zmin
A (L)
B (R)
3.9 Wiring
3.9.1 E.U.I. and XLR Connection
XLR: Pin 1 = Ground (or lifted via 15 Ω resistor)
Pin 2 = Hot (inphase)
Z ≥ *Zmin
Pin 3 = Cold (out of phase)
3.9.3 Parallel-Mono Operation
Always use symmetrical (balanced) shielded cable to connect the amplifier.
Parallel operation of the two channels together.
Input
Input
LINK B
LINK A
Channel B
Channel A
VORTEX
Zres ≥ 0,5*Zmin
A
2
1
2
1
1
2
1
2
3
3
3
3
B
The output terminals of the two channels are configured in parallel using an
internal relay. The (single) load is connected either to the output of channel A
or to that of channel B (as if in stereo). While the total output of the amplifier
remains the same and the output voltage level is also the same as in stereo op-
eration, the minimum impedance that can be connected is reduced by half due
to the fact that current capability is doubled. Only channel A-Input is active.The
channel B-Input is inactive – turn the volume on channel B down to zero. This
To
Channel B
To
Channel A
Input Ground Lift in
position: grounded
Input
Ground
Lift
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.14
Download from Www.Somanuals.com. All Manuals Search And Download.
mode is useful when, for example, 3 identical loudspeakers are to be operated
with the same power.
3.9.5 SPEAKON Connection
Both SPEAKON connectors are connected to channel A and channel B outputs.
The pin configuration of the SPEAKON-connectors is as follows:
3.9.4 Mono-Bridge Operation
Upper SPEAKON:
Bottom SPEAKON:
Pin 1+
Pin 1-
Pin 2+
Pin 2-
Channel A signal
Channel A ground
Channel B signal
Channel B ground
One-channel mono bridged operation.
VORTEX
Pin 1+
Pin 1-
Pin 2+
Pin 2-
Channel B signal
Channel B ground
Channel A signal
Channel A ground
A
Z ≥ 2*Zmin
Input
Channel A
Upper SPEAKON
B
The second channel processes the same input signal, but with reversed phase.
The (single) load is connected between the two positive channel outputs using
a suitable connected SPEAKON connector.While the total output of the amplifier
remains the same,both the available output voltage and the minimum impedance
that can be connected are doubled, as compared with stereo operation. Only
channel A-Input is active – turn the volume on channel B down to zero.
Input
Channel B
WARNING !
In Mono-Bridge mode RMS output voltages are as high as 230 V. Wiring
to the speaker loads must conform to NEC Class 3 safety standards or its
equivalent that meets all national and local electric codes.
All customer specific cables may only be manufactured by qualified
suppliers/personnel. All cabeling or rewiring work must be carried out by
qualified personnel.
Bottom SPEAKON
*Zmin = 2 Ω for VORTEX 6, 4 and 2.6
*Zmin = 4 Ω for VORTEX 200V
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.15
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING !
4.1 Controls
SPEAKON connectors marked with the lightning flashes indicate high vol-
tages that are potentially life threatening.
4.1.1 Volume Control
A microprocessor-controlled DCA (Digital Controlled Attenuator) with a control
resolution of 12 bits per channel is integrated into the signal path. This means
that the signal is not subject to an A/D followed by a D/A conversion with
associated losses.
Wiring to these terminals requires installation by an instructed person or
the use of ready-made leads or cords.
Using a DCA instead of the “conventional” VCA significantly reduces distortion
and, at the same time, it improves the noise characteristics. A volume control
with 41 notched settings controls the DCA via a microchip.
These settings have been selected to correspond to human hearing
characteristics (logarithmically) and therefore guarantee an optimal range of
settings for practical applications. Each channel can be set individually except
when operating in mono modes whereby only channel A is active.
Custom wiring should only be carried out by qualified personnel.
To prevent electric shock, do not operate the amplifier with any of the
conductor portion of the speaker wire exposed.
NOTE:
For reasons of safety and performance, use only high-quality fully insu-
lated speaker cables of stranded copper wire. Use the largest wire size that
is economically and physically practical, and make sure the cables are no
longer than necessary.
IMPORTANT:
When connecting speaker cabinets in parallel, always use all the contacts
in both SPEAKON connectors. If not, this may cause permanent damage to
the connectors and considerably reduce performance.
Set the volume to zero before turning on the amplifier to prevent the occurrence
of sudden high volume levels which may cause damage to your hearing and/or
the speakers.
The volume controls are also used to set the CAI address. (See 5.2.2 CAI Address
Settings)
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.16
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.2 Gain Selector
4.1.4 Limiter Switch
This switch on the rear of the VORTEX allows the maximum amplification
attainable to be set directly in the input stage.
This switch is located at the rear of VORTEX. It allows you to set the mode of
the limiter.There are three modes (See 4.3.1 Clip Limiter and 4.3.4 Speaker Protect
Limiter):
The VORTEX amplifier has a 26 dB and 32 dB
voltage gain setting along with a 1,4 V sensitivity
setting.
Right position:
Clip Limiter: On
Speaker Protect: On
4.1.3 Gain and Input Sensitivity
Middle position:
Clip Limiter: Off
Speaker Protect: On
The table shows input sensitivity per channel for a given gain and load. It also
shows the gain for the 1,4 V input sensitivity.
Left position:
Model
26 dB
32 dB
1,4 V
Clip Limiter: Off
Speaker Protect: Off
VORTEX 200V
3200 W @ 4 Ω
1900 W @ 8 Ω
1000 W @ 16 Ω
5,67
6,18
6,34
2,84
3,10
3,18
39,0 dB
VORTEX 6
VORTEX 4
VORTEX 2.6
3000 W @ 2 Ω
2100 W @ 4 Ω
1200 W @ 8 Ω
3,88
4,59
4,91
1,95
2,30
2,46
4.2 Indicators
37,5 dB
35,3 dB
32,0 dB
4.2.1 On LEDs (multifunctional)
Under normal operation, after the amp has started, the green On LEDs are per-
manently lit. A variety of different sequences of flashing LEDs are used to indi-
cate other operating states and errors in the relevant channels of the power
amp. (See 6.1 Flashing sequences for On LEDs)
2000 W @ 2 Ω
1500 W @ 4 Ω
920 W @ 8 Ω
3,17
3,88
4,30
1,59
1,95
2,15
1300 W @ 2 Ω
750 W @ 4 Ω
450 W @ 8 Ω
2,56
2,75
3,01
1,28
1,38
1,51
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.17
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.2 Signal LEDs
If the amplifier is overdriven for prolonged periods, the Clip LED will appear red
to alert the user more effectively (the green component of the LED is switched
off).
The green Signal LED is illuminated when the voltage level at the output reaches
approx. 4 V; this corresponds to a power of approx. 4 W over a 4 Ohm resistor.
Monitoring the output current and clip via the LEDs can aid the detection of
incorrectly wired components and faults in the loudspeakers at an early stage.
(See 6 Troubleshooting)
4.3 Power Amp Protection Systems
4.3.1 Clip Limiter
If the power amp is overdriven, the clip detection circuit triggers the micro-
processor. The processor reduces input signal level by controlling the DCA.
The strategy is implemented in software. For sinusoidal input signals the
microprocessor limits the input signal in such a way that non-linear distortions
of the signal never exceed 1 %.
4.2.3 Clip LEDs (multifunctional)
The colour of the bi-coloured (green/red) LED changes between red, green and
yellow depending on the load and the signal modulation conditions. (Yellow is
created by a mixture of red and green light).
The Clip Limiter can work on each channel independently (except in the two
mono-operation modes).To disable the Clip Limiter, see 4.1.4 Limiter Switch.
4.3.2 Under Impedance Limiter
As a result of incorrectly connected or defective loads,under impedance or even
short circuits may occur in one or both power amp channels.
The microprocessor constantly calculates the load impedance at the output
channels. If an impedance of less than 1,33 ohms/channel (2,7 ohms/channel
for VORTEX 200V) is detected,the microprocessor limits the signal to the power
amp until a subsequent measurement indicates that impedance has risen to a
safe level. Whenever the Under Impedance Limiter is active, the corresponding
channel’s On LED is turned off. (See 6 Troubleshooting)
The intensity of the green light is defined by the current passing through
the output stage of each channel (lowest brightness is proportional to
approximately 1 A, the maximum brightness reflects the maximum output
current). The red colour indicates the amount of signal clipping in each
respective channel. If the green LED (current indicator) and red LED (clipping
indicator) light up simultaneously, the Clip LED is yellow.
4.3.3 SOA Protection
To ensure that the power transistors are only used in the Safe Operation Area
(SOA), the SOA-protection in stereo mode switches back the rail voltages of the
respective power stage. In mono modes the rail voltages of both channels are
switched back.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.18
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3.4 Speaker Protect Limiter
4.3.6 DC Servo
Whenever the SOA protection of the power amp switches back the current rail
there could be a small clipping at the output; but the microprocessor is also
triggered by this protection and will reduce the signal level immediately to
minimise the effect.
To prevent DC Offset at the speaker output the VORTEX is fitted with two DC
Servos. (Hence there are no capacitors in the signal path!)
4.3.7 Over Current Protection
The user can decide either to use Speaker Protect or not. If you use this amp
for low frequencies (bass / Sub bass) and you want to squeeze the absolute
maximum out of it, Speaker Protect can be switched off. For all other appli-
cations (e.g. Full Range) it’s recommended to keep Speaker Protect switched
on.
The output stage is permanently monitored for possible current surges. There
are two limiting levels of over current depending on output voltage.These limits
will be set automatically. This improves reliability without degrading sound
quality when driving complex loads.
4.3.8 Thermal Protection
4.3.5 DC Protection
The microprocessor uses several sensors in the amp in order to ascertain tem-
perature data. If the microprocessor detects a temperature of more than 85 °C
at the heat sinks, the input signal on that channel is reduced. If the temperature
exceeds 100 °C, the main SMPS is switched off.
Each output of the power amp is constantly monitored for persistent DC voltage
levels. If the 3 V threshold voltage is exceeded at any of the outputs, the main
SMPS will shut down and the channel will be automatically switched off. The
microprocessor performs a sophisticated strategy to locate the cause of the
malfunction. DC can be located in the output stage, driver stage or at the input
of the amplifier.
The On LED of the overheated channel will start a blinking-sequence.
(See 6 Troubleshooting)
Output Stage
When a DC voltage is located at an output stage, the main SMPS remains
switched off. The On LEDs will show a flash sequence corresponding to this
malfunction. (See 6 Troubleshooting)
4.4 Mains Protections
4.4.1 Inrush Current Limitation
Within 2 seconds of the VORTEX being switched on, the inrush current limiter
will increase mains current from nearly zero to nominal value. This value
depends on program material, output level and speaker loads.
Driver Stage
When a DC voltage is located at the driver stage only the defective channel’s
output stage and the DCA are muted. The other channel continues to work.
The On LED of the defective channel will indicate the malfunction by starting
the relevant flash sequence. (See 6 Troubleshooting)
4.4.2 Mains Over Voltage Detection
Mains Over Voltage Detection is always operative. When the mains voltage
exceeds approx. 267 V (230 V operation), 134 V (120 V operation) or 117 V (100 V
operation),the amplifier will switch off.When the mains voltage returns to nomi-
nal value, a soft start occurs.
Amplifier Input
When DC is located at the input stage only the DCA of the affected channel
is muted. The other channel continues to operate normally. If the DC signal
at the input vanishes, the microprocessor will de-mute the affected channel
and the amplifier will work as usual again.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.19
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4.3 Mains Failure Detection
4.6 Fans
Mains Failure Detection is always operative. When the mains supply is
interrupted for about 2 mains cycles, the amplifier will switch off. When the
mains voltage returns to a normal value, a soft start occurs.
The fans mounted in your VORTEX operate permanently, but as long as the
temperature remains below 40 °C, they run at their slowest speed and can
hardly be heard.The highest detected temperature from either channel controls
the speed of the fans. Above 40 °C the speed is increased until it reaches its
maximum value.
4.4.4 Fuse Protection
The average mains current can peak temporarily, depending on the load
impedance and type of signal, at values several times higher than the nominal
value allowed by the fuse protection.
Continuous monitoring of the fuse protection status allows the conditions that
would trigger the fuse protection to be predicted. In order to avoid shut-down
of the amplifier due to current overload, the amplitude of the input signals will
be limited.
The limitation of the input signal allows a 6 kW VORTEX power amplifier to
be operated reliably from a mains power supply of 230 V/16 A (120 V/30 A;
100 V/30 A).
4.5 Main SMPS Protections
4.5.1 Over Current Protection
Main SMPS (Switched Mode Power Supply) transformer current of your VORTEX
is continuously monitored. If over current occurs, the main SMPS immediately
stops working. Should there be an internal failure, this feature prevents other
parts being damaged.
4.5.2 Thermal Protection
The temperature of the main SMPS transformer of your VORTEX is permanently
monitored. If the temperature exceeds 85 °C, the microchip reduces the input
signals of both channels. If the temperature surpasses 100 °C, the main SMPS is
switched off. The On LEDs will start a blinking sequence corresponding to this
malfunction. (See 6 Troubleshooting)
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.20
Download from Www.Somanuals.com. All Manuals Search And Download.
4.7 Filter Cleaning
For changing the filter, no tools are required: first, gently slide the whole plastic
filter assembly a few millimetres to the left and lift it from the front panel. Next,
beginning on one of the long sides, carefully unclip the moulded surround (4)
from the cradle (2) and then carefully pull the CAMCO badge (5) out of the four
fastening holes with both hands. Remove the foam filter (3) and clean it with a
mild dishwashing detergent and warm water. Once dry, replace the foam filter
carefully into the cradle and repeat the dismantling procedure in reverse. Insert
the five pins on the filter frame into the clip apertures (1) and slide the filter
carefully to the right to secure.
The air intake on the front of your VORTEX is fitted with a removable filter
system. If the filter becomes clogged, the unit will not cool as efficiently as it
should and may result in reduced output levels.
VORTEX Filter Assembly
1 Clip Apertures
3
2 Injection Moulded Cradle
3 Foam Filter
4
4 Injection Moulded Surround
5 Injection Moulded CAMCO Badge
5
1
2
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.21
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 E.U.I.2 (Extended User Interface)
5.1. 1 What Are The Possibilities Using The E.U.I.2?
CAUTION! Always switch off and unplug the VORTEX from mains, before
making alterations to the E.U.I. card.
The E.U.I.2 is a very powerful interface, which allows access to most of the
system parameters, such as volume, input signal, mute, output current, clip
signal, temperature and more. You can use the E.U.I.2 as a filter, remote control,
signal processing device and more… Please contact your dealer/distributor or
CAMCO to customise the E.U.I.2 according to your wishes.
The E.U.I. card contains the Rear XLR Panel as standard. Other input cards are
available (See 5.1.1 What Are The Possibilities Using The E.U.I.2?).
To remove the E.U.I.2 unscrew the two Phillips head screws at the left and right
end of the XLR-Panel and carefully slide out the E.U.I.2.
To refit the E.U.I.2, carefully insert it. Pay attention that the cable is not clamped.
5.2 CAI (CAMCO Audio Interface)
CAI is a bus system, in which all significant device functions can be monitored
externally and remotely controlled using a master PC. Up to 99 devices can be
controlled in parallel in each phase of the bus system, which simply consists of
a two-core insulated cable. For more complex operations, the Master can serve
multiple busses. For more information, please contact your dealer or distributor.
ATTENTION! Don’t forget to tighten the screws!
CAI allows:
To control the output-level of each Channel independently
(exception: mono modes, only Channel A is affected)
To mute each channel independently
(exception: mono modes, only Channel A is affected)
To switch the VORTEX into Standby (and back again)
To monitor temperature, output-signal, clip, output-current.
5.2.1 Wiring
To connect the VORTEX to your CAI system use a fully-wired telephone-type
cable with RJ12 connectors. For longer distances, use higher grade cable, like
RS485, DMX512 for AES/EBU digital audio. Using the second connector, CAI
signals can be sent to other VORTEX amplifiers (or to other CAI controlled
devices). A linear network topology is recommended with 100 Ohm termination
at its end. Please refer to RS485 specifications.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.22
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.2 CAI Address Settings
To see the address you can use the scale markings of the potentiometers.
You will find the digits 0,1,...,9 on the 10 scale spacings.
The CAI address selection procedure will not affect the operation of the VORTEX
but whilst this procedure is active, the volume cannot be adjusted by using the
pots.
4
5
3
6
2
1
7
8
Briefly press the Enter-Switch . This push button switch can be accessed
through the 3 mm hole in the front panel between the On/Off switch and the
LEDs. Only operate this switch with an insulated object.
4
5
9
3
0
0
6
9
2
7
8
1
The current selected address will be immediately displayed but not auto-
matically stored or activated! After each turn of pot you have another 30
seconds to Timeout.You can exit this procedure without saving the new address
by briefly pressing the Enter-Switch
or waiting for Timeout (as described
above).
To store and activate the new address you have to press the Enter-Switch for
3 seconds.This new address is stored in an EEPROM,which holds the information
even if the amp is subsequently disconnected from the mains.
Be sure to set the CAI-Master-PC to this new address. If not, the communication
will be interrupted.
The current address will then be displayed by the On LEDs.
Flashing of On LED channel A indicates the tens of the address
Flashing of On LED channel B indicates the units of the address
Example of LED sequences for different address settings:
Address
On LED Channel A ⇒TENS
0* flash
On LED Channel B ⇒UNITS
1* flash then short pause
5* flashes then short pause
01 (factory settings)
25
2* flashes then short pause
These sequences are repeated for 30 seconds (timeout). Then the On LEDs
return to their normal function.
NOTE: Ensure you return both pots to their original position after address
selection is complete, otherwise the amplifier will change its volume level
to the new pot positions!
To change CAI address,turn the appropriate volume potentiometer to the required
address (volume pot channel A => TENS, volume pot channel B => UNITS).
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.23
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.3 CAI Status Indicator
This green LED indicates the presence of communication between PC and the
amp.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.24
Download from Www.Somanuals.com. All Manuals Search And Download.
6.1 On LED Flashing Sequences
Examples of LED Sequences
When switching on the amp the On LEDs flash twice accompanied by a flash of
Clip LEDs.This is normal for the ‘Start’sequence of the VORTEX.
LED sequence:
Channel 1 :
Channel 2 :
Malfunction:
Channel 1: high temperature with signal attenuation
Channel 2: normal operation
When switching off the amp the On LEDs flash several times followed by a
flash of Clip LEDs. This is normal for the ‘Shut Down’ sequence of the VORTEX.
(It is the same as the loss of the mains voltage.)
LED sequence:
Malfunction:
Channel 1 :
Channel 2 :
In the following table you will find the possible LED sequences of the On LEDs:
Channel 1: DC, output stage defect
Channel 2: main SMPS off
Operating Status
Description of repeated sequences
LED Sequence ( ) = flash, (__) = off
Normal (no failure)
Permanently lit
Power Fail
(i.e. switch off)
Short 50 ms flash + 950 ms pause
750 ms flash + 250 ms pause
250 ms flash + 750 ms pause
250 ms flash + 250 ms pause
3 * flashing + 0.5 s pause
High Temperature
signal attenuation
Over Temperature
main SMPS off
DC
reason unknown
DC
input-signal-fault
DC
4 * flashing + 0.5 s pause
fault in driver stage
DC
5 * flashing + 0.5 s pause
output stage defect
Output Stage Defect
without DC
6 * flashing + 0.5 s pause
Main SMPS off
(unless high temperature/
power fail)
2 * flashing + 0.5 s pause
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.25
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2 Problem: No Sound
Indication: On LED(s) sequence
Indication: On LEDs not lit
Clip LEDs not lit
Please refer to the On LED flashing sequences table to find out which protection
is active.High temperature will cause an attenuation of output level! DC will cause
the amp to mute or shut down.
Check AC plug.
Confirm that AC outlet works by plugging in another device.
If the On LED sequence indicates “DC, Input Signal Fault”, switch off the
VORTEX and unplug the amp to disconnect it from the signal source. If the
On LED shows the same sequence when the VORTEX is switched on again,
the amp will need to be serviced by a qualified technician.
Indication: On LEDs lit
Signal LED not lit
Make sure the signal source is operating and try another cable.
Check position of Volume Pots.
All other On LED sequences that shut down or mute the VORTEX indicate a
serious internal fault. At this point, turn the VORTEX off, remove AC power
and have the amplifier serviced by a qualified technician.
Indication: On LEDs lit
Signal LEDs responding to signal level
Check the speaker wiring for breaks.
Try another speaker and cable.
6.4 Problem: No Channel Separation
Check the mode indicators on the front panel and make sure the mode
selector on the rear panel is in the Stereo-position.
Make sure other equipment in the signal path such as mixers and
preamps are set for stereo, not mono.
Indication: On LED(s) sequence
The amplifier is in protective muting. Refer to On LED flashing sequences table
to find out the cause for the mute.
Overheating will cause protective muting.
If the fans aren’t running the amplifier requires servicing
6.5 Problem: Distorted Sound
Indication: On LED lit
6.3 Problem: No Sound or Sound Is Too Low
Indication: On LED not or sporadically lit
Signal LED not lit
Signal LED responding to signal level
Clip LED lit only green
A faulty speaker or a loose connection could cause this. Check the wiring
and the speakers systematically (i.e. step by step) and replace them if
necessary.
Clip LED lit
Under Impedance Limiter is active.The load impedance is abnormally low or
shorted.
The signal source might be clipping. Keep the VORTEX volume pots at
least halfway up so that the source does not have to be overdriven.
Keep the VORTEX Volume Pots at least halfway up and try changing input
sensitivity from 1,4 V to 32 dB or 26 dB with the Gain Selector on the rear.
Unplug each speaker one-by-one. If the On LED indicates normally when
you disconnect a cable, that cable or speaker is shorted.
Take care not to use too many speakers in parallel, which would result in
an impedance that is too low for normal operation!
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.26
Download from Www.Somanuals.com. All Manuals Search And Download.
6.6 Problem: Hiss
Unplug the amplifier input to check that the hiss is coming from the source
or from a device upstream. Erratic or popping noises indicate an electronic
fault in the offending unit.
To keep the noise floor low, operate the primary signal source at full level,
without clipping.
Avoid boosting the signal further between the source and the amplifier.
6.7 Problem: Squeals and Feedback
Microphone feedback must be eliminated by the mixer controls. If noise
continues to build up with no microphone gain, there is a serious fault in
the signal processors or cables. Working in stages from the signal source
towards the amplifier and check each device in the signal path by reducing
its gain or by unplugging it.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.27
Download from Www.Somanuals.com. All Manuals Search And Download.
VORTEX 2.6
VORTEX 4
VORTEX 6
VORTEX 200V*
Output Power
1 kHz,THD ≤ 0,1 %,
1 x 2600 W @ 4 Ω
1 x 1500 W @ 8 Ω
1 x 4000 W @ 4 Ω
1 x 3000 W @ 8 Ω
1 x 6000 W @ 4 Ω
1 x 4200 W @ 8 Ω
1 x 6400 W @ 8 Ω
1 x 3800 W @ 16 Ω
in mono-bridge mode
1 kHz,THD ≤ 0,1 %, both channels driven
Duration limited by fuse / thermal protection for RL < 8 Ω
in stereo mode or RL < 16 Ω in mono-bridge mode.
2 x 1300 W @ 2 Ω
2 x 750 W @ 4 Ω
2 x 450 W @ 8 Ω
2 x 2000 W @ 2 Ω
2 x 1500 W @ 4 Ω
2 x 920 W @ 8 Ω
2 x 3000 W @ 2 Ω
2 x 2100 W @ 4 Ω
2 x 1200 W @ 8 Ω
2 x 3200 W @ 4 Ω
2 x 1900 W @ 8 Ω
2 x 1000 W @ 16 Ω
Measurement at 2 Ω without preconditioning (EN 60268-3)
1 kHz,THD ≤ 1 %, both channels driven
2 x 1500 W @ 1,8 Ω
Circuitry
Bipolar, Class H 2-step
high efficiency circuit
Bipolar, Class H 3-step
high efficiency circuit
Bipolar, Class H 3-step
high efficiency circuit
Bipolar, Class H 3-step
high efficiency circuit
Signal to Noise-Ratio
>103 dB
>106 dB
>109 dB
>112 dB
20 Hz - 20 kHz, 8 Ω, unweighted
>105 dB
>108 dB
>107 dB
>110 dB
A-weighted
Typical1)
Max2)
Typical1)
Max2)
Typical1)
Max2)
Typical1)
Max2)
Power Consumption @ 230 V
(both channels driven)
Idle
8 Ω
1 A
Idle
8 Ω
4 Ω
2 Ω
0,8 A
50 W
Idle
8 Ω
4 Ω
2 Ω
1 A
Idle 1,1 A
60 W
60 W
60 W
3 A
9 A
4,4 A
16,2 A
5,5 A
21 A
16 Ω 5,1 A
17,5 A
320 W
1250 W
550 W
2500 W
700 W
3200 W
560 W
2550 W
4 Ω
4,3 A
15 A
6,5 A
28 A
8 A
35 A
8 Ω
4 Ω
8 A
31 A
510 W
2200 W
880 W
4300 W
1100 W
5800 W
1000 W
4750 W
1,8 Ω
7,2 A
30 A
10 A
40 A
12 A
60 A
12 A
50 A
1005 W 4800 W
1450 W
6600 W
1800 W
9400 W
1700 W
8000 W
Multiply currents by 2 for 120 V / Multiply currents by 2,3 for 100 V
1) 1/8 of max Output Power with pink noise to represent typical music signal
2) max. rated Output Power (see above)
* VORTEX 200V Output Power @ THD ≤ 1 %
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.28
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequency Range
20 Hz - 20 kHz 0,15 dB
8 Ω, 10 dB below rated power
Input Impedance
Voltage Gain
40 kΩ balanced
selectable: 26 dB, 32 dB, or 1,4 V input sensitivity
inrush-current limitation, temperature monitoring of transformers and heat-sinks,
output DC protection, SOA protection, output over current protection,
under impedance limiter, intelligent mains fuses protection
switchable clip- and speaker protect limiter
Protection Circuits
Limiter
Fan
2 temperature dependent speed-controlled axial fans
input ground lift switch on back panel
Ground Lift
Indicators
LEDs for On, Signal, Clip, Mode, indicating additionally Output Current and
faults such as DC and High Temperature
Input Connectors
Output Connectors
Modes of Operation
Options
3-pin XLR, male and female per channel, pin 2 = hot (inphase)
one 4-pole SPEAKON connector for each output channel (wired using 2 channel cable)
Stereo, Mono-Bridge and Parallel-Mono
Extended User Interface / E.U.I.2 – modules for any kind of EQ
< 0,01 %
THD+N (typical)
20 Hz - 10 kHz, 8 Ω,
10 dB below rated power
SMPTE (typical)
< 0,01 %
20 Hz - 20 kHz, 8 Ω load,
10 dB below rated power
Damping Factor
> 400
8 Ω, 1 kHz and below
Dimensions (WxHxD)
Net Weight
483 x 88,9 x 422 mm (19”, 2U)
12,4 kg
3
Shipping Dimensions (WxHxD)
Shipping Weight
615 x 135 x 540 mm (0,045 m )
15 kg
We reserve the right to make technical alterations without prior notice
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.29
Download from Www.Somanuals.com. All Manuals Search And Download.
+180
+135
+90
+45
+0
-45
-90
-135
-180
Hz
Hz
Figure 8.1
Figure 8.3
Gain vs. frequency (Ch1, Ch2)
Phase vs. frequency (Ch1, Ch2)
(Measurements of a typical performance of a VORTEX 6)
(Measurements of a typical performance of a VORTEX 6)
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
20
50
100
200
500
Hz
1k
2k
5k
10k
20k
20
50
100
200
500
Hz
1k
2k
5k
10k
20k
Figure 8.2
Figure 8.4
Channel separation vs. frequency @ 10 W / 4 Ω (Ch2 => Ch1, Ch1 => Ch2)
(Measurements of a typical performance of a VORTEX 6)
Common mode rejection ratio (Ch1, Ch2)
(Measurements of a typical performance of a VORTEX 6)
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.30
Download from Www.Somanuals.com. All Manuals Search And Download.
1000
800
600
400
200
0
Hz
Hz
Figure 8.5
Figure 8.7
Output impedance vs. frequency @ 1 Amp RMS injected current (Ch1, Ch2)
equivalent 11 mΩ + 2,1 uH
Damping factor into 8 Ω (Ch1, Ch2)
equation: damping factor = loaded impedance / amplifier output impedance
(Measurements of a typical performance of a VORTEX 6)
(Measurements of a typical performanceof a VORTEX 6)
-20
-20
-30
-40
-50
-60
-70
-80
-90
-30
-40
-50
-60
-70
-80
-90
-100
-100
-110
-120
-110
-120
20
50
100
200
500
1k
2k
5k
10k
100u 200u 500u 1m 2m
5m 10 m 20m
Vrms
50m 100m 200m 500m
1
2
5
Hz
Figure 8.6
Figure 8.8
THD+N vs. input voltage @ 1 kHz, 4 Ω (Ch1, Ch2)
(Measurements of a typical performance of a VORTEX 6)
THD+N vs. frequency (BW 22 kHz), 10 dB below clip, 4 Ω (Ch1, Ch2)
(Measurements of a typical performance of a VORTEX 6)
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.31
Download from Www.Somanuals.com. All Manuals Search And Download.
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
100u 200u 500u 1m 2m
5m 10m 20m
Vrms
50m 100m 200m 500m
1
2
6
Figure 8.9
CCIF difference frequency method (10,5 kHz and 11,5 kHz) vs. input level
@ 4 Ω (Ch1, Ch2) (Measurements of a typical performance of a VORTEX 6)
-20
T
-30
-40
-50
-60
-70
-80
-90
-100
100u 200u 500u 1m 2m
5m 10m 20m
Vrms
50m 100m 200m 500m
1
2
6
Figure 8.10
SMPTE intermodulation distortion (60 Hz and 7 kHz) @ 4 Ω vs. input level
(Ch1, Ch2) (Measurements of a typical performance of a VORTEX 6)
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.32
Download from Www.Somanuals.com. All Manuals Search And Download.
2707
3000
5000
3961
1991
2113
4000
3000
2956
2000
1000
0
2186
1549
1084
1823
2000
1000
0
1128
931
1029
Peak power
Peak power
2
Distortion limited
4
4
Distortion limited
output power (0,1 % THD)
8
output power (0,1 % THD)
Impedance / Ω
8
Impedance / Ω
16
Figure 8.11
Figure 8.13
VORTEX 200V (Measurements of a typical performance)
VORTEX 4 (Measurements of a typical performance)
1760
5000
2000
4023
4000
3000
2000
1000
0
1305
3090
2715
988
1000
2113
1458
1257
755
528
450
Peak power
Peak power
0
2
2
Distortion limited
output power (0,1 % THD)
Distortion limited
output power (0,1 % THD)
4
4
Impedance / Ω
Impedance / Ω
8
8
Figure 8.12
VORTEX 6 (Measurements of a typical performance)
Figure 8.14
VORTEX 2.6 (Measurements of a typical performance)
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.33
Download from Www.Somanuals.com. All Manuals Search And Download.
9.1 Summary Of Warranty
9.4 How To Obtain Warranty Service
CAMCO guarantees the VORTEX amplifier to be free from defective material
and/or workmanship for a period of six (6) years from the date of sale. When a
defect occurs under normal installation and use, CAMCO will repair the product
under this warranty. In this event, please return the amplifier to your dealer/dis-
tributor together with a copy of your sales receipt as proof of purchase.
You must notify your dealer/distributor of your need for warranty service.
All components must be shipped in the original packaging.
This warranty provides that examination of the returned product must indicate,
in our judgment, a manufacturing defect.
9.2 Items Excluded From This Warranty
CAMCO is not liable for any damage caused by shipping accidents, misuse,
abuse, operation with incorrect AC voltage, operation with faulty peripheral
equipment, modification, or alteration without prior factory approval, service by
an unauthorised service center, and normal wear and tear. Amplifiers on which
the Serial Number has been removed or defaced are not eligible for warranty
service.
9.5 CAMCO’s Product Improvement
9.3 What CAMCO Will Do
CAMCO reserves the right to improve the technical standard of its products
without giving prior notice. If in any doubt, please consult your dealer/distri-
butor or contact CAMCO directly for clarification.
CAMCO (or its appointed agent) undertakes to rectify any defect, regardless of
the reason for failure (unless excluded from this warrenty), by repair, replace-
ment, or refund, as it sees fit.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.34
Download from Www.Somanuals.com. All Manuals Search And Download.
PLEASE ENCLOSE THIS COMPLETED FORM WITH THE AMPLIFIER
DO NOT SEND SEPARATELY
Owner’s Information
Nature Of Problem
Company Name: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Contact: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Address: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Telephone: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Facsimile: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
eMail Address: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Model: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Serial Number: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Purchase Date: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Please describe the conditions that existed when the problem occured and what
attempts were made to correct it: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Expired Warranty
If the warranty has expired, payment will be:
Cash/Cheque
VISA
Other equipment in your system: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
MasterCard
Shipping Address
To transport the amplifier, the original packing materials must be used.
Please return the amplifier to the following address or your nearest CAMCO
appointed distributor.
dealers/distributors.
CAMCO Produktions- und Vertriebs-GmbH für Beschallungs- und Beleuchtungsanlagen, Fischpicke 5, D-57482 Wenden, Germany
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.35
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Maintenance Information
12 Decomissioning
Cleaning and servicing the inside of the amplifier must never carry out by un-
During the decomissioning process of the amplifier, all legally prescribed rules
and procedures must be adhered to.
qualified personnel.The amplifier must never be opened by unqualified person-
nel.
Cleaning and servicing work on the inside of the amplifier must only be carried
out by qualified personnel.
Qualified personnel is defined as a person who has gained specialised relevant
knowledge of electronic engineering through education, training and experi-
ence and who has sufficient knowledge of all relevant governmental work
safety regulations to be in a position to judge the safe functioning of power
amplifiers based on technical rules according to IEC 60065.
(IEC 60065 (DIN EN 60065) “Safety Requirements for Audio, Video or simlar
Electronic Appliances”)
In order to guarantee the safe functioning of the amplifier, it has to be checked
regularly, depending on its application but at least once a year, by a properly
qualified person.
Advice on how to carry out these checks can be found in DIN VDE 0702-1“Safety
Checks for Electronic Appliances”.
An amplifier that is considered to be unsafe must be labelled accordingly and
stored in a safe place to prevent this amplifier being used mistakenly.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.36
Download from Www.Somanuals.com. All Manuals Search And Download.
Mailing Address:
CAMCO Produktions- und Vertriebs-GmbH
für Beschallungs- und Beleuchtungsanlagen
Fischpicke 5
D-57482 Wenden
Germany
Telephone:
+49 (0) 2762 408-0
Facsimile:
+49 (0) 2762 408-10
Internet:
Email:
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.37
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MANUAL
VORTEX 6, 4, 2.6 and 200V
P.38
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|