7. Specification
General Specification
PRECAUTION
Power Supply Requirement..................................................DC 12V
Maximum Power Output...................4 x 80W(measured at DC 14.4 V)
Dimensions(w x h x d)...........................................178 x 50 x 165mm
WARNING: TO REDUCE THE
RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION
DVD Deck Specification
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Format.....................................DVD/VCD/JPEG/MP4/MP3/WMA/CD
Video System....................NTSC/PAL/PAL-M/PAL-N/AUTO(optional)
Audio System..............................................................24 bit/96KHz
Loading System.......................................................... Auto Loading
Mounting Angle.................................................................0 to +/-30
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Video Specification
Video Type...................................................................16:9 and 4:3
Video Output level......................................Composite:1.0± 0.2Vp-p
Load impedance: 75 ohms
The lightening flash with arrowhead symbol, within an equilateral triangle, is
intended the alert the user to the presence of uninsulated dangerous voltage
within the products enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
Horizontal Resolution................................................................500
Audio Specification
+0
Audio Output(Analog audio)..........................................2.0 -1.0Vrms
Frequency Response.............................20Hz ~ 20KHz(at 1KHz 0 dB)
S/N Ratio(Audio).............................................≥90dB(at 1KHz 0 dB)
Separation..............................................................................50dB
The exclamation point within an equilateral triangle is intended to alert user to
the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
!
Radio Specification
FM Section
Frequency range.......................................87.5MHz - 108.0MHz(EU)
87.5MHz - 107.9MHz(USA)
Usable sensitivity......................................................................3uV
I.F Frequency....................................................................10.7MHz
CLASS 1 LASER PRODUCT
Laser product symbol: located on the rear panel of the unit, indicate this player is a class
laser product, only use weak laser and no hazardous radiation outside of the unit.
MW Section
Frequency....................................................522KHz - 1620KHz(EU)
530KHz - 1710KHz(USA)
1.Read through this instruction manual before installation and use.
2.Do not touch the power plug with wet hand.
Packing List
3.Switch off the main power when the unit is not in use. (Disconnect the power plug from
the power outlet when you do not intend to use the unit for a prolonged period of time.)
Before moving the unit, remove the disc from the unit/ tray first.
4.Do not open the cover or touch any of the components exposed out of the unit, only for
qualified technicians.
Main Unit
Remote Control
Panel Case
Instruction Manual
1 PC
1 PC
1 PC
1 PC
1 PC
5.Do not expose the unit under direct sunlight or nearby objects that radiate heat to avoid
damage the unit.
Warranty Card
6.Do not place the unit in moist and humid conditions, which effect the pick-up of the unit
lead to out of work.
AUX In Lines with 3 RCA Plugs and
1 Single Crooked Plug
3P L=1.5M
3P L=1.5M
1 PC
1 PC
1 PC
2PCS
1 PC
1 PC
1 PC
7.Place the unit on a flat surface and ventilative condition. Please ensure the ventilation
holes are not covered to avoid overheating and malfunction.
8.Clear the panel and case with soft dry cloth only, do not apply any kind of thinner,
alcohol or sprays.
9.The apparatus shall not be exposed to dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on the apparatus.
Audio/Video Lines with 6 RCA Plugs
Rear Bracket Plate
Key Plates
Screw 5 x 25 PA
Spring Washer D=5.0MM
Plain Washer M5 x 10
Download from Www.Somanuals.com. All Manuals Search And Download.
6. The Trouble Shooting
Contents
Please read the user s manual carefully before using the DVD player. If you have any troubles
in using this player, try to solve the problems by the suggestions mentioned below. If you can
not remove the trouble after using all the suggestions, please contact the company or the
technical service center authorized by us. For the sake of your safety, please do not open the
cover and repair the player by yourself, if that, it may cause electric shock.
1. Before Operation...........................................................................................3
1.1 Glossary................................................................................................ 3
1.2 Precautions............................................................................................3
1.3 Maintenance and Cleaning of Discs..........................................................4
1.4 Battery Information of the Remote Control.................................................4
1.5 The Remote Control Description...............................................................5
1.6 Locations and Names of the Controls........................................................6
1.7 Description of the Rear Cabinet....................... ........................................7
1.8 Description of the ISO Female Connector..................................................7
1.9 Unit Installation......................................................................................8
NO PICTURE, SOUND AND INDICATION
*
*
*
*
Ensure that the power switch is on.
Ensure that the wall inlet is ok.
Ensure that the power cord is not damaged or the fuse is not blown.
Ensure that the power plug is connected to the inlet tightly.
NO SOUND BUT HAVE PICTURE
*
*
*
*
*
Ensure that the player s audio output has a good connection with TV s audio input.
Check whether the audio connector is damaged.
Check whether you have turned down the volume.
Ensure that you have set the right AUDIO setup of the player.
Ensure that the audio is not under mute.
2. Common Operation........................................................................................9
3. Radio Operation..........................................................................................10
4. Basic Disc, USB or MMC/SD Operation..........................................................12
4.1 Begin Playback......................................................................................12
4.2 Pause Playback.....................................................................................13
4.3 Stop Playback .......................................................................................13
4.4 Select Chapter/Track with the >>|/|<< Buttons..........................................13
4.5 Select Chapter/Track with the Number Buttons.........................................13
4.6 Select Chapter/Track with the Root/PBC Menu.........................................13
4.7 Terminate the Playback..........................................................................14
NO PICTURE BUT HAVE SOUND
*
*
*
*
*
Ensure that the player s video output has a good connection with TV s video input.
Ensure that you have turned your TV to the AV input channel connecting to your player.
Check whether the video connector is damaged.
Ensure that you have set the right VIDEO settings of the player.
Check that parking brake wire is connected to parking brake switch such that wire is grounded
when parking brake is applied.
BLACK AND WHITE PICTURE OR SCREEN ROLLING
Ensure that you have set the right TV SYSTEM (e.g. PAL, NTSC) setting.
*
5. Advanced Disc, USB or MMC/SD Operation...................................................14
5.1 Playback with Speed..............................................................................14
5.2 Playback with Slow Speed......................................................................14
5.3 Playback with Still Frame.......................................................................15
5.4 Playback Repeatedly.............................................................................15
5.4.1 One/All Repeat..................................................................................15
5.4.2 A-B Repeat........................................................................................15
5.5 Playback in Scan Mode..........................................................................16
5.6 Playback from a specified Chapter/Track or a Specified Time....................16
5.7 Playback in Random..............................................................................16
5.8 Playback in Different Angle....................................................................16
5.9 Playback in Zoom Mode.........................................................................16
5.10 Change the Caption Language.............................................................17
5.11 Change the Audio Language................................................................17
5.12 Change the Video Signal System..........................................................17
5.13 Look over the Playback Status..............................................................17
5.14 Program Playback...............................................................................18
5.15 Playback the Picture CD in JPEG Format...............................................18
5.16 MP4 Operation....................................................................................19
5.17 ESP and ID3 Function..........................................................................19
5.18 USB and MMC/SD Reader Operation....................................................19
5.19 The DVD System Menu Setup Operation...............................................19
5.20 The Parental Control...........................................................................23
5.21 The Region Code................................................................................24
FLAWS OF PICTURE OR SOUND
*
*
*
*
Check whether the setting of AUDIO is right.
Check whether the disc is scratched or stained.
Check whether the AV connector and the output terminal is stained.
Check whether there is condensation inside the Lens. If so, leave the player off for an hour
or so, then try again.
*
Check whether the installation angle is less than 30.
DISPLAY NO DISC OR BAD DISC
*
*
*
*
*
*
Ensure that you have put the disc on the tray.
Check whether the disc is put in the reverse side.
Check whether the disc is distorted.
Check whether the disc is stained or scratched badly.
Ensure that the disc format is compatible to the player.
Ensure that the temperature inside the car is not too high. If so, cool off until the ambient
temperature returns to normal.
*
Replace another disc to insert it into the disc compartment.
REMOTE CONTROL IS INSENSITIVE OR DOES NOT WORK
*
Check the batteries of remote control and make sure that they are to be powerful and
good conductivity.
*
*
Direct the remote control to the IR sensor of the player.
Check whether there are some obstacles between the remote control and IR sensor.
SOME FUNCTION BUTTONS DO NOT WORK
*
*
*
Turn off the power, then turn on again.
Reset the unit to zero, then turn on again.
Remove the front panel from the unit, then install it again and then turn on again.
6. The Trouble Shooting..................................................................................25
7. Specification..............................................................................................26
THE RADIO DOES NOT WORK
Check whether the antenna cable is connected firmly. Or manually tune for a station.
*
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Before Operation
1.1 Glossary
5.21 The Region Code
Q: Not begin to playback but to display REGION ERROR after inserting disc into
disc compartment. Why ?
PBC (playback control)
It is a kind of signal(menu) recorded in the disc with SVCD or VCD2.0
format used for the playback control. For the discs contained PBC, It can
playback interactive software with the menu displayed on TV. And if the
disc contain still images, it can playback high definition of still image.
A: Because the DVD player and disc has respective region code. If the region codes
of them are not match with each other, the DVD player can not play the disc.
Title
Generally, the title is the important part of DVD disc. for example, the
theme part of movie is title 1, the part described how to make movie is title
2, the cast is title 3, etc. Every title contain a serial number that is easy to
lookup.
Appendix: The region code of DVD:
The Motion Picture Association of Amereca (MPAA) divided the world into 6
regions, and named every region a code, namely region code. The region codes
and the countries or areas represented by the region codes are as follows:
Chapter
Region 1: America, Canada, East-Pacific Inlands;
A title can be divided into several blocks, so that every block can be operated
as a unit, the unit is called chapter. The chapter contain a unit at least.
Region 2: Japan, West Europe, North Europe, Egypt, South Africa, Middle East;
Region 3: South-east Asian countries include Taiwan, Hong Kong, South Corea,
Thailand, indonesia, etc.;
Region 4: Australia, New Zealand, Central South America, South Pacific Inlands;
Region 5: Russia, Mongolia, Indian Peninsula, Middle Asia, East Europe, North
Corea, North Africa, North-west Asia etc.;
Track
It is the biggest component of VCD. Generally, every song of karaoke disc
is a track.
Region 6: China mainland.
PROTECTIVE CASE
Basically, when a DVD movie disc for the version of region 6 was decided not to
issue, we need to purchase another DVD player that can play the DVD movie disc
for the version of non-region 6. In order to view this disc, viewer who does not have
the non-region 6 DVD player facilities will have to spend extra sum of money to buy
it. The problems caused from the area code inconsistency between the disc and the
DVD player has pushed for the production of Unlock-Version DVD player facilities,
and some DVD disc sets allow user to modify the area codes for a limited number of
times. But note that only the discs produced by the 8 biggest filmmaking companies
of America restrict so, they are not one of original DVD format. That is to say, the
DVD movie discs not produced by the 8 biggest filmmaking companies of America
were not restricted by the rule of region code. Generally, they are called
FreeRegionCode discs or Full Region discs. The 8 biggest filmmaking companies
of America are as follows:
1.2 Precautions
Safety
FRONT PANEL
1. Power Source: The unit should be connected to power supply only of
the type described in the operating instructions or as marked on the unit.
2. The unit is designed for negative terminal of the battery which is
connected to the vehicle metal. Please confirm it before installation.
3. Do not allow the speaker wires to be shorted together when the unit is
switched on. Otherwise it may overload or burn out the power amplifier.
4. Do not install the detachable panel before connecting the wire.
5. The protective case is to safely keep the front panel(see the photo).
1. WarnerBros;
2. Colmbia;
Environment
3. 20thCenturyFOX;
4. Paramount;
5. Universal;
6. UA(UnitedArtist);
7. MGM(MetroDogwynMayer);
8. WaltDisney
1. Do not use this unit when water and moisture is near it.
2. If moisture forms inside the Lens, it may not operate properly. To correct
this problem, wait about one hour for the moisture to evaporate.
3. If the car interior is extremely hot, do not use the player until the car has
been driven for a while to cool off the interior.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Maintenance and Cleaning of Discs
Disc Maintenance
5.20 The Parental Control
Q:After inserting DVD disc into disc compartment, it will appear a dialogue window
that ask me input a password of 4 digit. Why ?
1. To keep the disc clean, handle the disc by its edge, do not touch the disc
surface of the play side.
2. Do not stick paper or tape on the disc. If there is glue (or analog) on the
disc surface, must wipe it up before using.
3. Do not expose the disc to direct sunlight, or nearby heat sources such as
caliduct, or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
A:This is because that the disc movie you are playing was rated with the Parental
Control, and the current rating level of DVD player is lower than one of current
disc. You must input right password and enter it to entry Parental Control setup
menu and then set a equal or higher rating level than one of current disc. So that
you can playback the disc.
4. Put the disc inside disc case to keep temperature after finishing playback.
Disc Cleaning
!
NOTE
1. Before playing, wipe the disc with a clean lint. wipe the disc outwards from
the disc center.
2. Do not use petrel, thinner, commercially cleaner or anti-static spray used to
plastic LP to wipe disc.
*
If you have not changed the password, the factory preset password for the DVD
player will be empty. So that you should input a desired password and input it
again to verify it to enter the Parental Control setup menu.
*
For the rating level setup of Parental Control of the DVD player, please refer to
the relative content of LOCK setup menu for details.
+
side up
B
Accessories: Parental Control
A
The Parental Control function of a DVD player can control the playback of movie
rated level in a disc. Can set the DVD player(include software player in PC) to be a
certain rating level with SETUP MENU on TV screen.If the rating level set in the
disc is higher than one set in the DVD player, the DVD player can not playback the
disc. Sometimes the Parental Control sequences in some discs are different from
each other. The rating level setup can be protected by the password. Therein, if you
select Unlock item, the Parental Control function will be invalid, the content of disc
will be played totally.
Fig.1
Fig.2
Fig.3
1.4 Battery Information of the Remote Control
Replace Battery in the Remote Control:
1.Before using the remote control for the first time, pull the insulating
sheet out of the remote control as the direction indicated by the
arrow.(see fig.1)
2.Press the movable block hold as the direction indicated by the A arrow
(See fig.2), then pull the battery holder out of the remote control as
the direction indicated by the B arrow(see fig.2).
3.Replace the old battery by a new battery with (+) polarity side upward.
(See fig.3).
4.Insert the battery holder to the original position in remote control.
(See fig.3).
Note about the Battery of the Remote Control:
1.Improper use of battery may cause overheating or explosion. so that
Result in injury or fire .
The disc movie can be designed as that the DVD player will playback the different
version of content of a same movie according to the different rating level set by
Parental Control. Depend on the DVD feature of seamless switching described above,
the scenes that are not fitting for children will be cleared or replaced by the other
fitting scene automatically.
All rating levels of Parental Control are as follows:
Unlock
1
2
3
4
5
6
7
8
Kid Safe
G
PG
PG 13
PG R
R
2.Battery leakage may cause damage to the remote control(Battery
Life: 6 months with normal use in normal room temperature).
3.Do not short the battery.
4.Do not throw the battery into the fire.
5.To avoid the risk of accident, keep the battery out of reach of children.
NC 17
Adult
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 The Remote Control Description
3
27
1
35
1. P/N BUTTON
2. MENU BUTTON
3. POWER BUTTON
4. ^ BUTTON
HUE
It is for adjusting the hue of the video output.
SATURATION
It is for adjusting the saturation of the video output.
SHARPNESS
It is for adjusting the sharpness of the video output.
14
4
2
29
32
33
6
8
5. >>| BUTTON
5.19.5 SPEAKER SETUP
34
13
5
6. > BUTTON
SPEAKER SETUP
DOWNMIX
7
7. |<< BUTTON
8. v BUTTON
31
30
10
11
12
40
9. SEL BUTTON
10. PLAY/PAUSE BUTTON
DOWNMIX
41
24
28
It is for selecting your desired sound effect when there is not central speaker
and sub-woofer. There are 3 mode: LT/RT, STEREO, VSS.
LT/RT: When playing a disc with PRO LOGIC Dolby stereo effect, choose the
item, so it will output audio signal with vivid theatre effect.
STEREO: If you choose the item, when outputting audio signal with 5.1 channels,
it will output the left and right channels of signal ; when outputting audio signal
with 2 channels, it will output the common 2 channels of stereo signal.
VSS: If you choose the item, when playing a disc recorded with 5.1 channels,
the main channel speakers can output audio signal with VSS effect.
16
15
11. NUMBER(0~10,+10
-10) BUTTONS
12. 10+/PTY BUTTON
18
17
21
22
26
25
23
36
37
13. SETUP BUTTON
14. MODE BUTTON
15. APS BUTTON
19
20
39
38
5.l9.6 DIGITAL SETUP
29. MUTE BUTTON
30. STOP BUTTON
31. VOLUME- BUTTON
32. < BUTTON
16. SEARCH BUTTON
17. RDM BUTTON
18. RPT BUTTON
DIGITAL SETUP
OP MODE
DYNAMIC RANGE
DUAL MONO
19. SUBTITLE BUTTON
20. TITLE/PBC BUTTON
21. ANGLE/ST BUTTON
22. ZOOM BUTTON
23. AUDIO BUTTON
24. CLK BUTTON
33. OK BUTTON
OP MODE
It is for selecting audio output mode
LINE OUT: It can linearly compress the audio signal. So the volume level is lower.
You should select the item at night.
RF REMOD: It can make the volume level higher. You should select it at daylight.
DYNAMIC RANGE
After selecting the compression mode of LINE OUT, set the item, so you can
adjust the linear compression ratio. If you set it to be FULL, the Peak-to-Peak
value of the audio signal is the minimum; if you set it to be OFF, the Peak-to-
Peak value is the maximum.
34. VOLUME+ BUTTON
35. BAND BUTTON
36. PROG BUTTON
37. OSD BUTTON
38. LOUD BUTTON
39. STEP BUTTON
40. TA BUTTON
25. A-B BUTTON
DUAL MONO
26. INT BUTTON
It is for selecting a desired audio output mode for the left and right ways of signal.
It is mainly for Karaoke of Ac3. There are 4 modes in all as follows:
STEREO, MONO L, MONO R, MIX MONO.
27. EQ BUTTON
28. LOC/SLOW-FWD BUTTON
41. AF BUTTON
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6 Locations and Names of the Controls
5.19.2 LANGUAGE SETUP
6
18
8
25
1
26
2
LANGUAGE SETUP
OSD LANGUAGE
AUDIO LANG
SUBTITLE LANG
MENU LANG
OSD LANGUAGE
This item is for selecting the language of the SYSTEM MENU and all operating
prompt interface displayed during playback.
AUDIO LANG
This item is for selecting a audio language.
10
12
5
24
3
16
4
17
7
11
13
14 15
9
23
22
SUBTITLE LANG
This item is for selecting a subtitle language.
MENU LANG
The figure of the front panel
This item is for selecting a disc menu language.
5.l9.3 AUDIO SETUP
AUDIO SETUP
AUDIO OUT
KEY
21
The figure of the Unit Chassis Facet After removing the Front Panel
19
28 27 20
AUDIO OUT
there is only ANALOG mode, i.e. SPDIF/OFF, not optional.
KEY
It is for selecting your desired basic music tone(from low to high).
1. POWER BUTTON
2. RELEASE BUTTON
3. MODE BUTTON
4. SEL BUTTON AND VOL KNOB
5. MUTE BUTTON
15. 6/+10 BUTTON
16. PTY BUTTON
17. AF BUTTON
5.l9.4 VIDEO SETUP
18. TA BUTTON
VIDEO SETUP
19. DISC SLOT
6. CLOCK BUTTON
7. BAND BUTTON
20. EJECT BUTTON
21. SD/MMC CARD SLOT
22. USB JACK
BRIGHTNESS
CONTRAST
HUE
SATURATION
SHARPNESS
8. >>| and |<< BUTTONS
9. APS BUTTON
23. AUX JACK
10. >||/1 BUTTON
24. STOP BUTTON
25. DISPLAY SCREEN
26. IR REMOTE SENSOR
27. REMOVING INDICATOR
28. RESET BUTTON
11. RPT/2 BUTTON
12. 3 BUTTON
BRIGHTNESS
It is for adjusting the brightness of the video output.
CONTRAST
13. RDM/4 BUTTON
14. 5/-10 BUTTON
It is for adjusting the contrast of the video output.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
7
For the DVD System Menu, there are 6 setup pages in all. They display as follows:
1.7 Description of the Rear Cabinet
5.19.1 SYSTEM SETUP
RED
R
RED
R
GREY
BLACK
SYSTEM SETUP
REAR RCA LINE OUT
FRONT RCA LINE OUT
Fixing Screw Bolt
GREY
BLACK
TV SYSTEM
TV TYPE
WHITE
L
WHITE
L
GREEN
PASSWORD
RATING
BLACK
Subwoofer
DEFAULT
AM/FM Antenna
BLACK
BLACK
TV SYSTEM
This product supports output of various TV system.
YELLOW
GRAY
GRAY
If your TV set has only NTSC or PAL system, the screen will blink and become
colorless when a wrong TV system is selected. In this case, press the N/P button
to switch the right TV system to match the TV color system.
TV TYPE
Fixed ISO Female Connector
VIDEO OUT
YELLOW
The setup item is for matching TV screen size.
Note: Use the clip end of a Ground Line provided by manufacturer to connect the Fixing Screw Bolt, use another end of the
Ground Line to connect the negative pole of the power source. Otherwise, the video on screen maybe flashes.
4:3 PS: Choose the item when connecting a TV set with 4:3 screen. When playing
the pictures with 16:9 size, the left and right parts of the video will be cut out,
and display in full screen.
4:3 LB: Choose the item when connecting a TV set with 4:3 screen. When playing
the pictures with 16:9 size, the top and bottom parts of the TV screen will be
turned into a black square respectively.
16:9: Choose the item when connecting a TV set with 16:9 wide screen.
PASSWORD
This setup item is for locking or unlocking the rating level of the Parental Control.
The defaulted state is locked. The defaulted password is 0000.
You can set a new password that you like: Select the PASSWORD item and then
press the > button to enter it, then input the original password 0000, and then
press the OK button to unlock it. Press the > button to enter it again, then input
a new password that you like and then press the OK button to make it effective.
Before the other persons see the Manual, you should get the password in mind
and cut out the part of PASSWORD in the Manual.
1.8 The Description of the Fixed ISO Female Connector
ISO Male Connector A
ISO Male Connector B
RATING
The item is for setting a new rating level of the Parental Control.
1. Select the PASSWORD item and then press the > button to enter it, then input
the password mentioned above, and then press the OK button to unlock the
setting of the rating level of the Parental Control.
2. Select the RATING item and then press the > button to enter it, then use the
direction buttons to select your desired rating level, then press the OK button
to confirm.
3. Select the PASSWORD item again and then press the > button to enter it, then
input the password, and then press the OK button to lock the new setting of
the rating level of the Parental Control.
Rear Right Speaker(+) Violet
Rear Left Speaker(+) Green
Constant 12V - Yellow
Rear Left Speaker(-) Green/Black
Front Left Speaker(+) White
Rear Right Speaker(-) Violet/Black
Power Antenna/Remote Turn on - Blue
Front Right Speaker(+) Grey
Ignition Switch Red
Ground Black
Front Right Speaker(-) Grey/Black
Front Left Speaker(-) White/Black
DEFAULT
This item is for making all setup items change back to original status.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. During JPEG playback, press one of the >/</^/v buttons to change the angle of
viewing picture that is displaying as follows:
1.9 UNIT INSTALLATION
>: 90 deg cw; <: 90deg ccw; ^:UP<-->DOWN; v: LEFT<-->RIGHT
During JPEG playback, press the PROG button to change the mode of refresh picture.
During JPEG playback, press the STOP button to stop playing and return to the root
menu.
*
*
During JPEG playback, the following buttons are not available: SLOW-FWD, MENU,
SUBTITLE, TITLE, ANGLE, STEP, AUDIO, RDM, INT and A-B.
In JPEG mode,the other operations are same as ones in MP3/WMA mode.
INSTALLATION INSTRUCTIONS
THE UNIT INSTALLATION IS ANTI-THEFT ONE. THE UNIT
CHASSIS WEARS A SLIDING METAL HOUSING. FIRSTLY
CONNECT THE POWER LINES, SPEAKER LINESAND
AUTO ANTENNAACCORDING TO MANUAL REQUIREMENT,
THEN INSTALL THE SLIDING METAL HOUSING IN A CAR
ACCORDING TO THE DIAGRAM.
5.16 MP4 Operation
TO BOOST UP THE CAPABILITY OF
ANTI-JAMMING, PLEASE FIX THE
METAL STRAP ON THE METAL
CONNECTED TO THE CHASSIS OF
THE CAR.
1. The root menu is displayed on TV when beginning to switch on DISC mode, then it will
automatically play the first file.
METAL STRAP
SELECT THE PROPER TABS
OF THE SLIDING METAL
HOUSING TO FIX THE
During playback, press the STOP button to stop playing and return to the root menu.
2. When displaying the root menu, press the direction buttons to select your desired
FOLDER or file, then press the OK or PLAY button to open the FOLDER, or play the
selected file.
SLIDING METAL HOUSING.
When displaying the root menu, you can also use the number buttons to select the
serial number of the file and play the file.
UNIT CHASSIS
*
*
The ANGLE, PROG, RDM, INT , MENU, SUBTITLE and TITLE/PBC buttons are not
valid.
The other functions are same as ones in DVD disc; but the RPT function is same as
one in MP3/WMA.
DASH BOARD
SLIDING METAL HOUSING
PLASTIC TRIM OUT
FRONT PANEL
5.17 ESP and ID3 Function
TO DRAW THE CHASSIS OUT OF THE
SLIDING METAL HOUSING, INSERT
THE LEFT AND RIGHT KEY PLATES
INTO THE TWO SIDES OF CHASSIS.
There is ESP function for all formats of discs.
In MP3/WMA mode, during playback, the information of the folder, file, song, artist and
album will be scrolling on the LCD display. As long as the current playing MP3 music
contains relevant ID3 tag information in version 1.0/2.0 format, the 3 items underlined
above will be scrolling on the LCD display; otherwise, they will not.
5.18 USB and MMC/SD Reader Operation
NOTE
Power on the DVD player, then insert the USB storage or MMC/SD Card(firstly flip down
the front panel), and then the monitor will display the root menu of the USB storage or
MMC/SD Card.
REMOVE THE DECK TRANSPORT
SCREWS BEFORE INSTALLING IT.
All the operations are same as ones of the corresponding format.
When you want to pull out the Card, firstly push it, and then pull it out.
REMOVE THE SLIDING METAL HOUSING
EJECT BUTTON
RESET BUTTON
5.19 The DVD System Menu Setup Operation
1. Press the SETUP button on the remote controller to access the DVD System Menu on
the monitor.
2. There are 6 setup pages in all for the System Menu. Press the > or < button to select
an desired setup page.
3. Press the ^ or v button to select an setup item in the selected setup page.
4. Press the > button to enter the setup item. Then press the v or ^ button to select a
desired mode of the setup item, finally press the OK button to confirm it.
*
*
Press the < button to return to the upper level.
Press the SETUP button again to exit the System Menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
5.14 Program Playback
2. Common Operation
It allows you to enter the order in which you want some chapters/tracks in
DVD/VCD/MP3/WMA/CD disc to play.
1 During playback, press the PROG button to enter a program interface as
follows:
1. To turn on/off the unit
Under standby or power off mode, press the POWER button to turn on the
unit.
Under power on mode, short press the POWER button to enter standby
mode(it still displays clock time and buttons lighting); long press the POWER
button to fully turn off the unit.
for DVD discs
for VCD/MP3/WMA/CD discs
P RO G R AM
P R O G R A M
T
C
T
C
T
C
T
C
2. To select function mode
1 _ _ _ _ 5 _ _ _ _ 9 __ _ _ 1 3 _ __ _
2 _ _ _ _ 6 _ _ _ _ 1 0 _ _ _ _ 1 4 __ _ _
3 _ _ _ _ 7 _ _ _ _ 11_ _ _ _ 15 _ _ __
4 _ _ _ _ 8 _ _ _ _ 1 2 _ _ _ _ 1 6 __ _ _
1 _ _: _ _ 5 _ _ : _ _ 9 _ _ : _ _ 1 3 _ _ : __
2 _ _: _ _ 6 _ _ : _ _ 1 0 _ _ : _ _ 1 4 _ _ : _ _
3 _ _: _ _ 7 _ _ : _ _ 11 _ _ : _ _ 1 5 __ : _ _
4 _ _: _ _ 8 _ _ : _ _ 1 2 _ _ : _ _ 1 6 _ _ : _ _
Press the MODE button to select TUNER, DISC(After inserting a disc), USB
(After inserting a USB storage), Card(After inserting a MMC or SD card), or
AUX IN mode.
3. To adjust sound level
Rotate the VOL knob on the front panel or press or hold the + or - button on
the remote controller to directly adjust the volume level.
4. To mute sound
P l a y
C l e a r
P l a y
C l e a r
2 Use the direction buttons to move cursor onto the desired place for inputting
the sequence number.
3 Use the number button to input desired sequence number of title/chapter/
track with desired sequence.
4 Use the direction button to move cursor onto Play item, then press the OK
button to play the programmed titles/chapters/tracks in programmed order;
only pressing the PLAY button also can play the programmed titles/chapters
/tracks in programmed order.
Press the MUTE button to turn on/off MUTE mode.
In MUTE mode, the MUTE mode can be released by pressing the following
buttons: MUTE, VOL or +/-, SEL.
5. To display and adjust the clock time
Press the CLK button to display clock time on the small monitor of the front
panel.
When displaying clock time, long press the CLK button to flash Minute of the
clock time, then rotate the VOL knob on the front panel or press the + or -
button on the remote controller to adjust Minute; and then briefly press the
CLK button to flash Hour of the clock time, then rotate the VOL knob on the
front panel or press the + or - button on the remote controller to adjust the
Hour.
*
*
*
*
To exit program playback, firstly press the STOP button, then press the PLAY
button to enter sequence playback; or press the PROG button twice again.
To remove the all programmed sequence numbers, move the cursor onto
Clear item, then press the OK button.
To change the programmed sequence, move the cursor onto the item you
want to change, input the desired sequence number.
6. To select a preset EQ mode
Press the EQ button to select the preset music equalizer curves: POP,
CLASS, ROCK, EQ OFF . The sound effect will be changed.
7. To remove the front panel
During VCD playback, if it is in PBC ON mode, at the same time of entering
the state of program playback, it turns off PBC mode.
Press the RELEASE button on the front panel to flip down the front panel
from the unit chassis, then you can remove the front panel.
8. To turn on/off LOUD mode
5.15 Playback the Picture CD in JPEG Format
1. The root menu is displayed on the monitor when beginning to switch on DISC
mode. (the TITLE is not available).
Press the LOUD button on the remote controller to turn on/off LOUD mode.
When turning on LOUD mode, it will enhance bass level immediately when
the bass is not enough.
In the root menu, the left file sort icon is for MP3/WMA file; the middle file sort
icon is for JPEG file; the right file sort icon is for VIDEO file. If one of these 3
file sort does not exist, you can not move cursor onto the file sort icon.
2. When displaying the root menu, press the direction buttons to select your
desired FOLDER, file or file sort icon, then press the OK or PLAY button to
open the FOLDER, or play the selected file, or play only this sort of file.
When displaying the root menu, you can also use the number buttons to
select the serial number of the file and play the file.
9. To reset the unit
When display is wrong, sound is distorted or the function buttons are dis-
available, firstly flip down the front panel and remove it, then use a needle
analog to press the RESET button to rehabilitate the distorted program to
zero.
10.To adjust the sound equalizer curves
To adjust the sound equalizer curves, briefly and repeatedly press the SEL
button to select the sound equalizer curves of VOL, BAS(without preset EQ),
TRE (without preset EQ), BAL, FAD, then rotate the VOL knob on the front
panel or press the + or - button to adjust level.
When you select a JPEG file sort icon, press the ^ or > button to select the
first JPEG file, then press the v button to select the desired JPEG file, finally
press the OK or PLAY/PAUSE button to display the JPEG picture in full screen
from the selected JPEG picture.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Radio Operation
ZOOM 2,ZOOM 3,ZOOM 4,ZOOM 1/2,ZOOM 1/3,ZOOM 1/4,ZOOM OFF.
Press one of the ^/v/>/< buttons to select the area you want to enlarge.
1. BAND BUTTON
In RADIO mode, press the BAND button on the remote controller or on the front panel to
select your desired radio band of FM1, FM2, FM3, MW1 and MW2, and the word means which
band is selected will be displayed on the small monitor of the front panel.
5.10 Change the Caption Language
2. TUNE/SEEK UP/DOWN BUTTONS
In RADIO mode:
In the state of DVD disc playing, press the SUBTITLE button repeatedly to
select the language of the caption or turn off the caption.(depend on the
media used.)
1) Long press the >>|/ |<< button to automatically search up/down for a available station from the
current frequency.
2) Briefly press the >>| / |<< button to manually search up or down with step by step for your desired
station from the current frequency.
In the state of VCD/MP3/WMA/CD disc playing, the button is not available.
3. APS BUTTON
5.11 Change the Audio Language
In RADIO mode:
1) When long pressing the APS button, the radio searches from the lowest frequency and checks
the signal strength level until 1 cycle search is finished. And then the 6 strongest stations are
preset to the corresponding preset number memory bank. The AS operation is implemented in
the each bank of the selected band. When the AS operation is finished, it will resume broad-
casting on the M1.(It can store 3x6 stations for FM and 2x6 stations for AM in all)
2) When briefly pressing the APS button on the front panel or the remote controller, the radio
searches for each preset station from the M1. When the field strength level is more than the
threshold level of the stop level, the radio is holding at that preset number for few seconds with
releasing mute, and then searches again. After finishing a circle of searching, it will stop
searching on the M1.
1. In the state of DVD disc playing, press the AUDIO button repeatedly
on the IR remote controller to select the desired language type.
(depend on the media used)
2. In the state of VCD disc playing, press the AUDIO button repeatedly to
select the sound mode of the MONO L, MONO R, MIX MONO and Stereo,
no language function.
3. In the state of CD/WMA/MP3 disc playing, the AUDIO button is invalid.
NOTE: In FM band, FM1,FM2,FM3 is checked one at a time.
5.12 Change the Video Signal System
In MW band, MW1, MW2 is checked one at a time.
During playback of DVD/VCD disc, press the BAND button on the front panel
or the P/N button on the remote controller repeatedly to change the VIDEO
SIGNAL SYSTEM mode.
4. PRESET STATION [ 1-6 ] BUTTONS
In RADIO mode:
1) To memorize the current frequency on the current band, long press any one of the six preset
buttons (1-6) .
2) To recall the preset memory on the current band, press one of the preset buttons [1-6] .
5.13 Look over the Playback Status
5. STEREO/MONO BUTTON
Press the ST button on the remote controller to select the STEREO or MONO sound mode for
FM band.
1. In the state of DVD disc playing, press the OSD button repeatedly on the
remote controller to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing title, the
serial number of the playing chapter, the elapsed time of the playing chapter,
the remained time of the playing chapter, the elapsed time of the playing title,
the remained time of the playing title, etc.
2. In the state of VCD/CD disc playing, press the OSD button repeatedly on the
remote controller to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing track, the
elapsed time of the playing track, the remained time of the playing track, the
elapsted time of the disc, the remained time of the disc.
6. LOC BUTTON
1) In RADIO mode, when the signal of the distance radio station are very weak and the receiving
effect is bad during tuning, check whether there is the word LOC on LCD. If there is the word
LOC on LCD, press this button to turn off the LOC function, then tune again for the distance
radio station;
2) In RADIO mode, when the signal of the local radio station are too strong to lead that the
interference to the receiving effect during tuning, press this button to turn on the LOC function
to display the word LOC on LCD, then tune again for the local radio station.
EUROPE USA
7. Changing radio system
3. In the state of MP3/WMA disc playing, press the OSD button repeatedly on
the remote controller to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing track, the
elapsed time of the playing track, the remained time of the playing track.
Radio System Toggle
Before installation, dialling the Radio System Toggle in
the left side face of the unit can change the radio system
The Radio System Toggle in
between Europe and USA. After it, you need to reset the
the left side face of the unit
system to zero.
In USA mode, the buttons of PTY, AF and TA in the front panel serve as ones of LOUD, EQ and
LOC ; the buttons of PTY, AF and TA in the Remote Control are not available.
Download from Www.Somanuals.com. All Manuals Search And Download.
8. PTY (PROGRAM TYPE) BUTTON
Press the PTY button shortly to select one of the following mode:
PTY MUSIC group- - PTY SPEECH group- - PTY OFF
While selecting PTY TYPE, its selection is implemented by preset buttons
(press one of the 6 preset buttons shortly and repeatedly to select the PTY
TYPE in the preset button) as follows:
5.5 Playback in Scan Mode
1. In the state of VCD(PBC OFF)/CD disc playing, press the INT button to play
the previous 15 seconds part of each track on the disc. Press the INT button
again to resume normal playback.
PTY music group ---------------PTY speech group --------------- OFF
1. POP M, ROCK M
2. EASY M, LIGHT M
3. CLASSICS, OTHER M
4. JAZZ, COUNTRY
5. NATION M, OLDIES
6. FOLK M
1. NEWS, AFFAIRS, INFO
2. In the state of DVD/MP3/WMA disc playing, the INT button is not available.
5.6 Playback from a specified chapter/track or a specified time
2. SPORT, EDUCATE, DRAMA
3. CULTURE, SCIENCE, VARIED
4. WEATHER, FINANCE, CHILDREN
5. SOCIAL, RELIGION, PHONE IN
6. TRAVEL, LEISURE, DOCUMENT
1. In the state of DVD disc playing, press the SEARCH button to display a
interface and highlight the title item, then use the number buttons to input
the serial number of the title; use the direction buttons to highlight the chapter
item, then use the number buttons to input the serial number of the chapter;
you can still use the direction buttons to highlight the time item, then use the
number buttons to input the desired time to start playback; finally press the
OK or PLAY button to play the selected chapter or play from the selected time.
When PTY MUSIC or PTY SPEECH is on, the PTY item and PTY word is
displayed on LCD.
After selecting a desired PTY item, it will search corresponding PTY infor-
mation, and stops if the corresponding PTY information is detected.
During 1 loop, if desired PTY is not found, PTY NONE is flashed, then return
to previous normal radio and PTY word disappear.
9. AF [ALTERNATIVE FREQUENCIES] BUTTON
When pressed the AF button short, the AF switching mode is selected and
the state of the AF switching mode is displayed by AF segment in display.
Segment off: AF switching mode off.
2. In the state of VCD/MP3/WMA/CD disc playing, press the SEARCH button to
display a interface and highlight the track item, then use the number buttons
to input the serial number of the track; you can still use the direction buttons
to highlight the time item, then use the number buttons to input the desired
time to start playback; finally press the OK or PLAY button to play the selected
track or play from the selected time.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not
received yet.
When the AF switching mode is selected, the radio checks the signal strength
of the AF all the time. The interval of checking time of each AFs depends on
the signal strength of the current station, from a few minute for the strong
station to a few seconds for the weak station. Every time that a new AF is
stronger than the current station, it switches over to that frequency for very
short time, and the NEW FREQUENCY is displayed for 1-2 second. Because
the mute time of the AF switching or the checking time is very short, it is
almost inaudible in case of normal program. (When AF flash on LCD, it will
search for the stronger RDS station. If AF and TP flash on LCD, it can only
search for the traffic announcement station).
5.7 Playback in Random
In the state of DVD/VCD(PBC OFF)/MP3/WMA/CD disc playing, press the
RDM button to switch between RANDOM (ON)/RANDOM OFF. When in
RANDOM (ON) mode, it will play in random.
5.8 Playback in Different Angle
In FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can
only receive and save the RDS program.
1. In the state of VCD/MP3/WMA/CD disc playing, the ANGLE button on the
IR remote controller is not available.
10. TA [TRAFFIC ANNOUNCEMENT] BUTTON
Press the TA button shortly to turn on TA search mode.
When traffic announcement is transmitted:
1).If the unit is in Disc Play mode, it will switch to radio mode temporarily.
2).Temporarily switch over to an EON linked station when EON detects a
traffic announcement on that other program, and TA, TP will be displayed
on LCD
2. In the state of DVD disc playing, press the ANGLE button repeatedly on
the IR remote controller to view in different angle.(This function is only
for the DVD discs with ANGLE function)
* TA interruption function:
The current traffic announcement is cancelled by pressing TA button
shortly.
* When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received
or saved only when traffic program identification code has been received.
5.9 Playback in Zoom Mode
In DVD/VCD mode, during playback, press the ZOOM button continuously
to enlarge a certain area of the images on the screen with these multiples:
Download from Www.Somanuals.com. All Manuals Search And Download.
During slow forward, press the PLAY button to resume normal playback.
The function is only for video.
4. Basic Disc, USB or MMC/SD Operation
4.1 Begin playback
5.3 Playback with still frame
1. Press the POWER button briefly to turn on the DVD player.
After turning on the DVD player, please turn on the monitor, and ensure that
the video output of the monitor is the video input from the DVD player
connected with the monitor.
If the unit is currently running DVD/VCD disc, press the STEP button
consecutively to display the still frame forward with step by step.
Press the PLAY button to resume normal playback.
?
Common Question
Q: There is not anything is displayed on TV screen when the DVD player is
turned on. How to solve the problem?
5.4 Playback Repeatedly
5.4.1 ONE/ALL Repeat
A: Ensure that the TV was set to right video input(not TV channel); for
example, if you make VIDEO1 INPUT of TV and DVD player connected
with each other, then you need set TV to VIDEO1.
1. In the mode of DVD disc playback:
Press the RPT button to select REP CHAPTER, REP TITLE, REP ALL
or REP OFF.
2. Press the REL button to flip down the front panel.
2. In the mode of VCD(PBC OFF)/CD disc playback:
press the RPT button to select REP ONE, REP ALL or OFF.
When it is in the state of PBC ON, during VCD disc playing, the RPT
button are not available.
3. Insert a disc into the Disc Compartment(Label surface up), then flip
up the front panel back to the previous position.
3. In the mode of MP3/WMA disc playback:
Press the RPT button to select REP ONE, REP DIR, REP ALL or OFF.
! NOTE
5.4.2 A-B Repeat
1. For some discs that are seriously scratched or poor manufacturing or
recording quality, it may not play.
Press the A-B button if you want to repeat a specific segment on a disc
that you define:
2. If the player can not read disc under normal condition, please try to
eject and reload the disc again.
1. Press the A-B button at a point (A) where you want it to be the start point
of the repeat segment. Press the A-B button again at a point (B) where you
want it to be the terminal point of the repeat segment. Then it will play the
segment repeatedly.
3. Remark:
1) In addition to normal CD and DVD, this unit supports to play CD-R,
CD-R/W, DVD-R and DVD-R/W as well; however, depending on the
conditions of the recording equipment, recording program or the disc
itself, some CD-R, CD-R/W, DVD-R or DVD-R/W may not play.
2. To cancel the A-B repeat mode and resume normal playback, press the A-B
button for the third time.
Note:
2) When dealing with CD-R, CD-R/W, DVD-R or DVD-R/W recording,
too high recording speed may result in poor signal quality and therefore,
it is recommendable to select as lower as possible recording speed.
During VCD/MP3/WMA/CD playback, points A and B must be within the
same track.
During DVD playback, points A and B can be selected from different chapters.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Pause Playback
In VCD mode
In the state of DVD/VCD/CD/MP3/WMA disc playing, press the PAUSE
button on IR remote controller to pause the playback, press the PLAY
button to resume normal playback.
1. When starting to turn on the PBC function, it will play from the beginning of
the disc till it display the PBC menu on TV screen if the disc include the PBC
menu.
2. Press the number buttons to select your desired track to play.
4.3 Stop Playback
In MP3/WMA mode
In the state of DVD/VCD/MP3/WMA/CD disc playing, press the STOP button
once to pause the playback, then press the PLAY button to resume the normal
playback; press the STOP button twice to full stop the playback, then press
the PLAY button to start playback from the beginning of the media.
1. The root menu is displayed on the monitor screen all the time(and the TITLE
or MENU button is not available).
2. Press the direction buttons to select your desired FOLDER, then press the
OK or PLAY button to open the FOLDER, and then press the direction buttons
to select your desired file, finally press the OK button to play the selected file.
4.4 Select Chapter/Track with the >>| / |<< Button
In CD mode, the TITLE, PBC, MENU buttons are disabled.
Press the >>| or |<< button during playback to select the next or previous track
/chapter to playback.
4.7 Terminate the Playback
Note: Press the >>| or |<< button multiple times to advance multiple chapters/
tracks forward or backward.
1. Press the REL button to flip down the front panel, then press the EJECT
button to eject the disc in the disc compartment. and then remove the disc .
4.5 Select Chapter/Track with the Number Buttons
2. Flip up the front panel back to the previous position, then press the POWER
button to turn off the DVD player.
In the state of DVD/VCD/MP3/WMA/CD disc playing, press one
of the 1~9 and the 0/10 number buttons to directly select and play the 1st to
10th track/chapter (the 0/10 button is used as the 10 button).
If you want to play the track/chapter that s serial number is bigger than 10,
use the 10+, 1~9 and 0/10 button. For example 1, to play the 13th track/
chapter, firstly press the 10+ button once, then press the 3 button. For
example 2, to play the 34th track/chapter, firstly press the 10+ button for 3
times, then press the 4 button.(the 0/10 button is used as the 0 button)
Note: long pressing the +10 or -10 button can play the next 10 or last 10
chapter/track(only for MP3/WMA).
5. Advanced Disc, USB or MMC/SD Operation
5.1 Playback with Speed
During normal playback, long press the >>|/|<< button continuously to fast
forwards or backwards at the following speeds: x2, x4, x8, x20, normal.
During speed playback, press the PLAY button to resume normal playback.
4.6 Select Chapter/Track with the Root/PBC Menu (If the disc includes the
root/PBC menu)
5.2 Playback with Slow Speed
In the state of DVD disc playing
During playback , press the SLOW_FWD button to execute the Slow
Forward function.
1. Press the TITLE button on the remote controller to display the title list.
2. Press the direction buttons to select your desired title, and then press the OK
or PLAY button to open the root menu of the selected title.
3. Press the direction buttons to select your desired chapter, finally press the
OK or PLAY button to play the selected chapter.
With each consecutive pressing of the SLOW_FWD button, the playback
speed decreases. The speed levels in Slow Forward as follows:
x1/2,x1/3,x1/4,x1/5,x1/6,x1/7,normal.
During playback, pressing the MENU button can directly display the main
menu of the media.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
