Bose Speaker System 15 User Manual

The Bose^®Acoustimass^®15 Series II and Acoustimass 16

Home Entertainment Speaker Systems

August 13 , 2002

AM264924_00_V.pdf

Bose Corporation

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Where to ﬁnd…

Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unpacking the carton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Placing your speakers to achieve realistic home theater sound . . . . . . . . . . . . . . . . . . . . . . . .

Front center cube speaker array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front left and right cube speaker arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear cube speaker arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Powered Acoustimass^®module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting the speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting front cube speaker arrays to the Acoustimass module . . . . . . . . . . . . . . . . . .

Connecting rear cube speaker arrays to the Acoustimass module . . . . . . . . . . . . . . . . . . .

Connecting the Acoustimass module to the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Checking the connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting the Acoustimass module to power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Upgrading your Acoustimass 15 Series II speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

For realistic home theater sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Adjusting the LFE level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Adjusting the bass/room compensation level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Setting your digital surround sound receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Be sure to get the digital audio signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting your analog surround sound receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Customer service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cleaning the speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Technical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Warranty period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

Before you begin

We appreciate your choice of the Bose^®Acoustimass^®15 series II or Acoustimass 16 home

entertainment speaker system.

Bose Virtually Invisible^®speaker technology allows you to enjoy lifelike home performances

from the very latest surround-sound encoded movies, CDs, and television shows, without a

room full of speakers. The cube speaker arrays, along with the powered Acoustimass mod-

ule, reproduce the full-spectrum of sound from multi-channel digital programming. Integrated

Signal Processing assures full bass performance from all channels at all listening levels,

regardless of your receiver settings.

Your stereo VCR, stereo television, or DVD player sends the encoded program material to the

surround-sound receiver, which interprets and distributes the information to the powered

Acoustimass module. The module delivers the bass for all channels and sends appropriate

sounds to each cube speaker array. The sound mix varies with different program types: dia-

logue is usually sent to the center cube speaker array, a visual soundstage is created by the

left and right front cube speaker arrays, and you feel as if you are in the center of the action

because sounds and special effects are directed to the rear cube speaker arrays. At any point

in a surround-sound performance, you may hear sound from one, a few, or all of the cube

speaker arrays.

To select surround-encoded program material, look for the terms Surround, Dolby Surround,

the double-D symbol 3, Dolby Digital 1, other digital formats, or the word “sur-

round” preceding a TV broadcast. Your system is compatible with home theater receivers.

You can also enjoy a wide variety of stereo programming that is not surround-encoded.

Unpacking the carton

WARNING: The powered Acoustimass module weighs 33 pounds (15 kg). Use good lifting

practice to avoid injury.

WARNING: To avoid danger of suffocation, keep the plastic bags that wrap these speakers

out of the reach of children.

Note: This product is not to be powered by any DC-to-AC inverters that may be found in

automobiles, recreational vehicles, boats, ships, or other similar situations.

Carefully unpack the carton contents (Figure 1):

1. Remove the brown inner carton containing the cube speaker arrays.

2. Gently roll the carton over onto its side.

3. Slowly pull the Acoustimass module from the carton.

4. Stand the module up.

If the cube speaker arrays or the module appear damaged, do not use them. Repack every-

thing in the original carton and contact your authorized Bose dealer immediately. Or, to con-

tact Bose directly, see the list of ofﬁces and phone numbers enclosed with your system.

Note: Now is a good time to record the serial number of these speakers on page 2 of this

guide and on your warranty card. Please save all packing materials for possible future use.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

Figure 1

Carton contents

20-ft (6.1m) system input cable

Three 20-ft (6.1m) front speaker cables

Rubber feet for front center

Powered Acoustimass^®

module

cube speaker array

With Acoustimass 15 Series II system

With Acoustimass 16 system

Six cube speaker arrays

Five cube speaker arrays

Two 50-ft (15.2m) rear speaker cables

Three 50-ft (15.2m) rear speaker cables

Power cord (1)

Europe UK/Singapore

USA/Canada

Australia

Placing your speakers to achieve realistic home theater sound

A suggested home theater layout is shown in Figure 2. You may want to place the speakers

differently to take advantage of the sound characteristics of different rooms. Here are some

suggested guidelines for placing your speaker system:

• The cube speaker arrays are identical and can be used for any channel.

• All cube speaker arrays are magnetically shielded to prevent interference with a TV picture.

• The top and bottom sections of the cube speaker arrays can be rotated to create

room-ﬁlling sound patterns (Figure 3).

• Bose^®wall brackets and ﬂoor stands can extend your placement options. See “Accesso-

ries ” on page 17. Please follow wall bracket instructions carefully. Proper mounting will

ensure optimum performance and safety from your system.

Note: The Acoustimass 15 Series II may be upgraded by adding a center rear cube speaker

array. See “Upgrading your Acoustimass 15 Series II speaker system” on page 12.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

For Acoustimass^®15 Series II

For Acoustimass 16

Figure 2

Suggested home theater

layouts

- 15'

(2 - 5m)

- 15'

(2 - 5m)

2'+

(0.6m+)

CAUTION: To prevent interference, keep the Acoustimass module at least 2 feet (.6m) from

your TV set.

For Acoustimass 15 Series II

For Acoustimass 16

Figure 3

Sound patterns

Front center cube speaker array

The front center cube speaker array localizes action and dialogue on your screen. Sound

should seem to come from within the picture.

• Place the front center cube speaker array above, below, or on top of your television. If

below, be sure that it is not supporting the weight of the television in any way.

• Keep the front cube speaker array as close to the vertical center of the screen as possible,

for the most accurate dialogue reproduction.

CAUTION: Choose a stable and level surface for your cube speaker arrays. Vibration can

cause them to move, particularly on smooth surfaces like marble, glass, or highly polished

wood. If you are placing the center cube speaker array on top of your television, use the set

of four rubber feet provided. You may obtain additional rubber feet (part number 178321-04),

free of charge, by contacting Bose^®Customer Service. See the list of phone numbers

included with your system.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

Front left and right cube speaker arrays

The front left and right cube speaker arrays create a sound image wider than the screen that

seems natural to viewers sitting anywhere in the room. You can place the cube speaker arrays

near a TV screen with no picture interference. Place the front cube speaker arrays on either

side of your TV, at least 6 feet (2m), or as much as 15 feet (5m) apart (see Figure 2).

Rear cube speaker arrays

The rear, or surround cube speaker arrays add discrete sounds and special effects that

expand the visual image, bringing the viewer into the center of the action. The rear cube

speaker arrays may carry dialogue as well.

• Position the left and right rear cube speaker arrays to allow the sound to reach the viewer

from both sides, rather than from directly behind (see Figure 2).

• Place the rear cube speaker arrays at ear height (when seated) or higher, if possible.

• Rotate the top and bottom sections of the rear cube speaker arrays to direct the sound to

the front and back of the listener.

• If you have a center rear cube speaker array (Acoustimass 16 system or upgraded Acousti-

mass 15 Series II system), place it so that it is centered between the rear left and right cube

speaker arrays (see Figure 2).

Powered Acoustimass^®module

Bose^®Acoustimass speaker technology takes advantage of the fact that the source of pure

bass sound is difﬁcult to locate, so you can hide the powered Acoustimass module conve-

niently out of sight. Place the module at the same end of the room as the television monitor.

• You may hide the module behind furniture, but do not block the opening. Be sure there is at

least 2 inches (5 cm) between any surface and the front opening or the grille on the bottom.

• If the opening faces the wall it increases the bass; if it faces away it decreases the bass.

CAUTION: To prevent interference, keep the module at least 2 feet (.6m) from your TV set.

Figure 4

Note: Placing the module horizontally, or on

its side, may reduce ventilation, inhibiting its

ability to play at full output for extended

periods of time.

Powered Acoustimass

module placement

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

Connecting the speakers

CAUTION: Never connect the cube speaker arrays directly to a receiver output. Always con-

nect them to the powered Acoustimass^®module, then connect the module to the receiver.

CAUTION: Never use broken or frayed wiring, which can result in electrical shock or damage

to your system. The supplied cables are not intended for in-wall installation. Check local

building codes or enlist a qualiﬁed installer.

Connecting front cube speaker arrays to the Acoustimass module

Three individual 20-foot (6.1m) speaker cables connect the center, right, and left front cube

speaker arrays to the Acoustimass module (Figure 5). Be sure to match the correct cable with

the corresponding speaker location. Front speaker cables have blue RCA connectors at one

end with L (left), R (right), or C (center) molded into the connectors. The other ends of the

cables have two wires. The red collars on the + wire are labeled LEFT, RIGHT, or CENTER.

Note: The center rear cube speaker array is included with the Acoustimass 16 system or may

be added to an Acoustimass 15 Series II system. For upgrading information, see “Upgrading

your Acoustimass 15 Series II speaker system” on page 12.

Figure 5

Cube speaker array

connections to the

Acoustimass module

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

1. Connect the wire pair marked CENTER to the center cube speaker array. Press the termi-

nal tab on the back of the cube speaker array. Insert the marked (+) wire into the red ter-

minal and the plain (–) wire into the black terminal. Release the tab to secure the wires.

2. Connect the wire pair marked RIGHT to the right front cube speaker array (to the right of

the TV as you face it).

3. Connect the wire pair marked LEFT to the left front cube speaker array.

4. Plug the other end of each cable into the CENTER FRONT, RIGHT FRONT, and LEFT

FRONT blue RCA jacks, respectively, on the Acoustimass^®module.

Connecting rear cube speaker arrays to the Acoustimass module

Each rear cube speaker array is connected to the Acoustimass module with a 50-foot (15m)

speaker cable (Figure 5). Be sure to match the correct cable with the corresponding speaker

location. Rear speaker cables have orange RCA connectors at one end with LR (left rear), RR

(right rear), or CR (center rear) molded into the connectors. The other ends of the cables have

two wires. The red collars on the + wires are labeled LEFT REAR, RIGHT REAR, or CENTER

REAR.

1. Connect the wire pair marked RIGHT REAR to the right rear cube speaker array (on your

right as you face the TV). Press the terminal tab on the back of the cube speaker array.

Insert the marked wire into the red terminal and the plain wire into the black terminal.

Release the tab to secure the wires.

2. Connect the wire pair marked LEFT REAR to the left rear cube speaker array.

3. If you have a center rear cube speaker array (Acoustimass 16 system or upgraded Acous-

timass 15 Series II system), connect the wire pair marked CENTER REAR to the center

rear cube speaker array.

Note: The Acoustimass 15 Series II system may be upgraded by adding a center rear cube

speaker array. See “Upgrading your Acoustimass 15 Series II speaker system” on page 12.

4. Plug the other end of each cable into the RIGHT REAR, LEFT REAR, and CENTER

REAR orange RCA jacks, respectively, on the Acoustimass module.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

Connecting the Acoustimass^®module to the receiver

The 20-foot (6.1m) system input cable connects the module to your surround receiver (see

Figure 6). The system input cable has a multi-pin connector on one end and several wire pairs

on the other. The wire pairs of the cable may be separated or “unzipped” as much as needed

to comfortably reach the surround receiver connections. Each wire pair is marked on the

cable jacket with RIGHT, LEFT, CENTER, RIGHT SURROUND, LEFT SURROUND, or

CENTER SURROUND to indicate where each wire connects to the receiver.

CAUTION: Before making any connections turn off your receiver and unplug it from the AC

(mains) outlet. Not doing so may result in damage to your system.

CAUTION: Do not connect the powered Acoustimass module directly to your TV unless it

provides surround decoding circuitry and ampliﬁed outputs for all channels.

1. Insert the multi-pin connector on the system input cable into the input jack on the Acous-

timass module. Tighten the two thumbscrews to assure a secure connection.

2. Connect each wire pair on the other end of the system input cable to your surround

receiver. Carefully match the polarity of the connections (+ to + and – to –).

• Attach each marked wire (+) to the appropriate + terminal.

• Attach each plain wire (–) to the appropriate – terminal.

Note: The RCA plug of the system input cable comes with a cover installed. Remove

this cover for connection to the LFE/SUBWOOFER OUT jack. If your receiver has no

LFE/SUBWOOFER OUT jack, leave the plug cover in place.

3. If applicable, connect the RCA plug marked LFE on the system input cable to the

LFE/SUBWOOFER OUT jack on your surround receiver.

CAUTION: Do not allow exposed wires to brush against each other; this could damage your

receiver.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

Figure 6

Acoustimass^®module to

receiver connections

Note: The center surround connection

is used only when a center rear

speaker is installed.

FRONT SPEAKERS A

Thumbscrews

CENTER

FRONT SPEAKERS A

CENTER

SURROUND SPEAKERS

LFE/SUBWOOFER

OUT

CENTER

Note: Cables may be

separated or “unzipped”

as much as needed to

comfortably reach the

surround receiver

connections.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Setting Up

Checking the connections

Check all connections from the receiver to the Acoustimass^®module and from the module to

the cube speaker arrays (Figure 5 and Figur e 6). Make sure all cube speaker arrays are con-

nected to the proper terminals according to their position in your room. Check that all wires

are connected to your surround receiver in phase (+ to + and – to –). Incorrect wiring can

result in a total loss of module output. Correct wiring problems before you plug your receiver

in and turn it on.

Connecting the Acoustimass module to power

Note: Bose^®recommends using a quality surge suppressor on all electronics equipment.

Voltage variations and spikes can damage electronic components in any system. A quality

suppressor can eliminate the vast majority of failures attributed to surges and may be pur-

chased at an electronics store.

After you have checked all system connections, plug the power cord of the powered Acousti-

mass module into an AC (mains) receptacle. Your Acoustimass speaker system will turn on

and off automatically as it receives a signal from your surround receiver.

Upgrading your Acoustimass 15 Series II speaker system

Your Acoustimass 15 Series II speaker system can be upgraded to provide you with 6.1 or

6 channel surround sound.

The 6.1 upgrade kit contains one black (PC 029661) or white (PC 029662) cube speaker array,

a 50-foot connecting cable, and complete connection instructions.

To purchase the 6.1 upgrade kit, contact your local authorized Bose retailer or call Bose

directly. See the list of Bose ofﬁces and phone numbers enclosed with your system. When

ordering, you will need to know the serial number of your Acoustimass module.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Using your system

For realistic home theater sound

CAUTION: The Acoustimass^®15 Series II and Acoustimass 16 speaker systems incorporate

an automatic protection circuit, which guards against most kinds of damage from electrical

stress or overload. This circuit activates at high volume levels to reduce output, causing a

slight decrease in volume. This is normal operation and indicates that power input may be

exceeding safe levels. Sustained listening at these levels is not recommended.

Adjusting the LFE level

The LFE (low-frequency effects) level control on your powered Acoustimass module

increases or decreases the relative level of low-frequency effects on movie sound tracks. Use

it to regulate the presence of these underlying deep bass sounds. Use the “test tones” feature

in your digital surround sound receiver to match the volume levels for each of the cube

speakers. Then use the LFE control on the Acoustimass module to match the volume of the

LFE channel to the cube speaker channels.

Adjusting the bass/room compensation level

This feature will allow you to ﬁne-tune your system after you have placed the Acoustimass

module in your selected location. If the room sounds “thin” or lacks bass, turn the BASS con-

trol in a clockwise direction to increase the bass level of the module. If the room sounds

“boomy” or has too much bass, turn the knob in a counter-clockwise rotation to reduce the

bass level of the module. The factory or detent setting is appropriate for a majority of listening

situations.

Setting your digital surround sound receiver

Your Acoustimass 16 or Acoustimass 15 Series II speakers are fully compatible with the

output from digital surround receivers. Integrated Signal Processing assures full bass

reproduction for all channels regardless of receiver settings. However, the following table

suggests a set of recommended receiver settings. The cube speaker arrays should be set to

LARGE in the receiver’s digital display menu. The LFE, or subwoofer, is set to ON. If applica-

ble, the crossover value should be set to the lowest number possible, typically 80 Hz.

Speaker

Receiver setting

LARGE

Left and right

Center

LARGE

Left and right surround

Center surround*

LFE/Subwoofer

LARGE

* Applies to Acoustimass 16 systems or upgraded Acoustimass 15 Series II systems. For upgrade

information, see “Upgrading your Acoustimass 15 Series II speaker system” on page 12.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Using your system

Be sure to get the digital audio signal

To be sure that the digital audio signal from your DVD player reaches your surround receiver,

connect the digital audio output from your DVD player to the digital audio input on your

receiver (Figure 7).

Before you play a DVD disc, be sure to select the digital output in the setup menu of your

DVD player. For additional setup and operating information, please refer to the owner’s guide

that came with your surround receiver.

Figure 7

Note: Use the optical or coaxial digital

input connections, but not both.

Digital signal connections

on a surround receiver

DIGITAL PLAY IN

PLAY IN

(COAXIAL)

(OPTICAL)

DIGITAL PLAY IN

PLAY IN

(COAXIAL)

(OPTICAL)

FRONT SPEAKERS

SURROUND SPEAKERS

REAR

CENTER

Setting your analog surround sound receiver

For analog surround sound (non-digital) applications, we recommend that you set the

surround-sound center mode of your receiver to WIDE. Instructions for this process vary,

depending on the brand and model of your surround receiver. Follow your receiver owner’s

guide for testing and adjusting the balance of each speaker.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Reference

Troubleshooting

If you have a problem with your Acoustimass^®speaker system, turn off your sound source

and try the following solutions. If you still have a problem, contact your Bose^®dealer to

arrange for service. To contact Bose directly, refer to the list of service ofﬁces and phone

numbers enclosed in the shipping carton.

Problem

What to do

System does not function

at all

•

Make sure the receiver and powered Acoustimass module are plugged into an operating

AC wall outlet and that the receiver is turned on.

Be sure to select a source at the receiver (video, CD, DVD, tuner).

No sound

•

Check the speaker connections.

Make sure that the powered Acoustimass module is plugged in.

For digital sound, be sure a coaxial or optical cable connects the digital output of the

DVD player with the digital input on your receiver.

Be sure the audio source selected is correct. For example, select DVD audio on your

receiver and player for DVD sound.

•

Disconnect any headphones.

Increase the volume.

No sound from cube

speaker arrays

•

Be sure the powered Acoustimass module is plugged in and the receiver is turned on.

Sound is distorted

•

Make sure speaker wire is not damaged.

Reduce the volume of external components connected to the receiver.

No bass

•

Be sure the speaker connections at the receiver/ampliﬁer are correct (+ to + and – to –).

Not enough or too much

bass

Move the powered Acoustimass module closer to a wall or corner to increase bass.

Move it farther away from a wall or corner to decrease bass.

Adjust the LFE Level or Room Compensation control.

•

No surround sound

Be sure your receiver is processing a signal from a Hi-Fi VCR, stereo TV, laserdisc, or

DVD player, or other surround-sound source.

•

If you are using the Dolby Pro-Logic mode, check that surround-sound is turned on.

If you are using digital programming, verify that the settings are correct at the receiver.

Be sure the source material (DVD, laser disc, or broadcast programming) is Dolby Digital

encoded.

Customer service

For additional help in solving problems, contact Bose customer service. See the list of service

ofﬁces and phone numbers enclosed in the shipping carton.

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Reference

Cleaning the speakers

The cabinets of your Acoustimass^®speaker system may be cleaned only with a soft dry cloth.

Do not use any sprays near the system or allow liquids to spill into any openings. Also, do not

use any solvents, chemicals, or cleaning solutions containing alcohol, ammonia, or abrasives.

The grille assemblies on the cube arrays may be carefully vacuumed, if necessary. Please

note that the drivers are located directly behind the grille cloth, and are easily damaged if

reasonable care is not taken.

Technical information

Features

Direct/Reﬂecting^®speaker technology

Virtually Invisible^®speaker design

Acoustimass speaker technology combined with Integrated Signal Processing

Magnetically shielded cube speaker arrays

Automatic system protection circuitry

Syncom^®computer quality control

Finish

Cube arrays: Black or Arctic White ﬁnish

Powered Acoustimass module: Scratch-resistant Black or Arctic White textured ﬁnish

Speaker driver complement

Cube speaker arrays: two 2.50-inch (6.35 cm) Twiddler^TMspeakers

Powered Acoustimass module: Three 5.25-inch (13 cm) woofers

Speaker size/weight

Cube speaker arrays: 6.2"H x 3.1"W x 4.0"D (15.7 cm x 7.8 cm x 10.2 cm) / 2.4 lb (1.1 kg)

Acoustimass module: 16.3"H x 8.1"W x 29.1"D (41.4 cm x 20.6 cm x 73.9 cm) / 45 lb (20.3 kg)

Acoustimass 15 Series II

Acoustimass 16

USA/Canada:

100-127V

USA/Canada:

Acoustimass

module power

rating

50/60 Hz 400 W 100-127V

50/60 Hz 400 W

Europe/Australia:

50/60 Hz 400 W 220-240V 50/60 Hz 400 W

Europe/Australia:

220-240V

Compatible with A/V receiv-

ers and ampliﬁers rated from

10 to 200 watts per channel,

rated from 4 to 8 ohms

Compatible with A/V receiv-

ers and ampliﬁers rated from

10 to 200 watts per channel,

rated from 4 to 8 ohms

Connectivity

72.5 lb (32.6 kg)

75 lb (33.8 kg)

Packed system

weight

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Reference

Warranty period

Accessories

Your Bose^®Acoustimass^®speaker system is covered by a limited transferable warranty.

Details of the warranty are provided on the warranty card that came with your system. Please

ﬁll out the information section on the card and mail it to Bose.

• Table stands: UTS-20B (black), UTS-20W (white)

• Floor stands: UFS-20B (black), UFS-20W (white)

• Wall brackets: UB-20B (black), UB-20W (white)

• Module input cable adapter for use with existing wiring:

PN267138-001 (black)

PN267138-002 (white)

• Module-to-cube speaker array cable adapter for use with existing wiring:

PN267139-001 (black)

PN267139-002 (white)

• Module 20 ft (6.1m) input extension cable:

PN267140-001 (black)

PN267140-002 (white)

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Framingham, MA 01701-9168 USA

264924 AM Rev.00 JN20951

^DownloadA^froM^m2^W6^w4^w9^.2^So4^m_^a0ⁿ0^ua_^lsV^.c.^op^md^.f^A•^llA^Mauⁿg^uu^als^st^S1^e3^ar,^ch20^An0^d2^Download.

Black Decker Mixer GM100 User Manual
Blanco Indoor Furnishings 501 306 User Manual
Bodum Coffeemaker 10096 User Manual
Bosch Appliances Range HGS3053UC User Manual
Boss Audio Systems Speaker System MC450 User Manual
Bushnell Binoculars 131054 User Manual
Bushnell Hunting Equipment 20 1925 User Manual
Char Broil Gas Grill 463742112 User Manual
Chicago Electric Saw 97580 User Manual
Christie Digital Systems Projector 104 006101 XX User Manual