Radio / Cassette
Bergamo RCR 148
Montana RCR 148
Wiesbaden RCR 148
Operating instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Quick reference ............................ 25
Changing the memory bank ................. 34 Tape operation ............................. 40
Storing stations ..................................... 34
Automatically storing the strongest
Inserting a tape ..................................... 40
Removing a tape................................... 40
Important notes ............................ 30
Precautions ........................................... 30
Traffic safety ......................................... 30
Installation............................................. 30
Accessories .......................................... 30
stations with Travelstore....................... 35
Fast Forward/Rewind ........................... 40
Recalling stored stations ...................... 35
Selecting titles with CPS
Scanning stored stations with
(Cassette Programme Search)............. 40
Preset Scan .......................................... 35
Switching the tape side (autoreverse).. 41
Scanning stations with Radio-Scan...... 35
Tape equalisation ................................. 41
KeyCard theft protection system 31
Selecting the seek tuning sensitivity .... 35
Scanning cassette titles with SCAN ..... 41
Operating the unit ................................. 31
Removing the KeyCard ........................ 31
“Training” a second KeyCard/
Replacing a KeyCard............................ 31
Displaying the radio pass data ............. 31
Short Additional Memory (S.A.M.)........ 32
Turn On Message (T.O.M.) .................. 32
Optical indication of anti-theft
Switching from stereo to mono............. 36
Listening to the radio during fast tape
Loudness .............................................. 36
winding with RM (Radio Monitor) ......... 41
PTY – Programme-Type....................... 36
Care notes ............................................ 41
Switching PTY on/off ......................... 36
DSC programming ....................... 42
Programme type ................................... 36
Checking the programme type of
Overview of DSC factory settings ........ 43
the station .......................................... 37
Displaying the selected programme
type .................................................... 37
Selecting a programme type ............. 37
Storing programme types.................. 37
Scanning stations with PTY-SCAN ... 37
PTY priority........................................ 38
Appendix ....................................... 44
protection .............................................. 32
Care of your KeyCard ........................... 32
Specifications........................................ 44
Blaupunkt telephone hotline ................. 44
Switching the audio source ........ 32
Radio operation with RDS ........... 33
AF - Alternative frequency .................... 33
REG - regional programme .................. 33
Selecting a waveband
(only Bergamo RCR 148) ..................... 33
Station tuning ........................................ 34
Receiving traffic programme
stations with RDS-EON................ 39
Traffic announcement priority on/off .... 39
Beep tone ............................................. 39
Switching off the beep tone............... 39
Automatic seek tuning start
(tape operation) .................................... 39
Adjusting the volume for traffic
Automatic tuning
/
....................... 34
Manual tuning with << >>.................. 34
Scrolling through the broadcasting
networks (FM only) ............................... 34
announcements and the beep tone...... 40
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick reference
that you should remove the KeyCard
before leaving your vehicle.
When pressing VOL-, the
volume will be adopted.
To programme the mute volume level,
proceed as follows:
(mute)
1 Switching on with the buttons:
Press one of the buttons illustrated
here after you have inserted the Key-
Card.
Switching on when the ignition is
switched off:
•
•
Adjust the desired volume.
Press for 1 second until you
hear a beep.
The unit will play at the pre-adjusted
volume.
Switch off with the ON button.
To keep on operating the set when the
ignition is switched off (KeyCard is in-
serted), proceed as follows:
Press ON after you hear the double
beep tone.
Now this volume level is stored as your
mute volume.
The unit will turn on.
4 Rocker switch
To prevent the battery from going
dead, the system will turn off automati-
cally after it has played for one hour.
Radio operation
Switching on/off with the KeyCard:
When turned on, the set can be
switched off and back on by removing
and re-inserting the KeyCard.
2 VOL+ / VOL-
To alter the volume.
Each time the set is switched on, it will
play with the pre-adjusted volume
(VOL FIX).
You may also change the VOL FIX set-
ting (see chapter “DSC programming”).
Note:
Be sure to read the information in the
section on “KeyCard theft protection
system”.
/
Station search
Up
Down
<</>> Up/Down in short intervals
(on FM only if AF is off)
3
Switching on/off via the ignition:
If the equipment has been connected
correspondingly, the set can also be
turned on and off with the vehicle igni-
tion.
For instantly muting the volume.
By pressing the
button the volume
On FM only:
can be muted immediately. “MUTE”
will appear in the display.
The function is cancelled by pressing
<</>> To scroll through the station net-
works when AF is on, e.g.NDR 1, 2,
3, 4, N-JOY.
After the ignition has been switched
off, a double beep tone will remind you
button
or VOL+.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape operation
Remote control
5 Display
RC 06 (optional)
a
c
d e f g h
i
j
k
/
Title selection (S-CPS)
b
Up
Down
Using the remote control you can
execute the same functions as with the
corresponding buttons of the car
stereo.
Fast forward
Fast rewind
a) NDR1 NDS - Station name
b) TR 1
- Track (side) 1 of the cas-
sette
Stop function by pressing the opposite key.
c) FM
d) 5
e) I, II, T
- Waveband
- Preset button (1-6)
- Memory bank I, II or
Travelstore
Extra rocker switch functions:
Further setting functions with
Exception:
Radio operation
f) lo
g) AF
- Seek tuning sensitivity
- Alternative frequency for
RDS operation
- A traffic station is being
received
- Priority for traffic stations
- Loudness
- Programme type function
AUD
DSC Mode
PTY
Condition: The corresponding function
is activated.
B
A
@
<<
<<
Press briefly.
To switch the FM memory bank.
h) TP
i) TA
j) LD
k) PTY
Press for approx. 1 sec.
To store the six most powerful sta-
tions automatically with Travelstore.
>>
To select one of the stations stored
on memory bank I, II or T.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
6 KeyCard theft protection system
To operate the set the KeyCard must
be inserted first.
7 FMT (Wiesbaden RCR 148,
Montana RCR 148)
8 AF
Alternative frequency during RDS op-
BND (Bergamo RCR 148)
For selection of the FM memory banks
I, II and T (Travelstore).
To switch over:
Press button repeatedly.
The selected memory bank will appear
in the display.
eration:
When “AF” lights up in the display, the
system will automatically seek a fre-
quency offering better reception of the
same RDS programme.
KeyCard
AF on/off: Press AF briefly.
Insert KeyCard
Regional function on/off:
When the KeyCard tongue is protrud-
ing out of the unit, insert the KeyCard
with the contact area facing up into
the slot in the middle of the area.
If necessary, pull the KeyCard forward.
Be sure to read the information in the
section on “KeyCard theft protection
system”.
Bergamo RCR 148:
Press the AF button for approximately
1 sec. until you hear a beep. “REG-
ON” or “REG-OFF” will appear in the
display (see chapter REG - regional
programme).
Additional selection of medium- and
long-wave stations, provided that “AM
ON” has been adjusted in the DSC
menu.
Travelstore
To store and recall the six most power-
ful stations with Travelstore.
To store: Press button for approxi-
mately 1 sec. until you hear a beep
and “T-STORE” appears in the display.
To recall: Select the memory bank “T”
and press the corresponding preset
button (1-6) briefly.
9 TA (priority for traffic announcements)
When “TA” lights up in the display, the
system will play traffic stations only.
Priority on/off: Press TA.
Flashing KeyCard tongue
When the radio is turned off and the
KeyCard removed, the KeyCard
tongue can be programmed to flash for
optical theft protection.
For more information see the section
on “DSC programming”.
: 1, 2, 3, 4, 5, 6 - preset buttons
You can store six stations for each of
the memory banks I, II, T, M and L.
To store a station: Press a preset
button during radio operation and hold
down until the set resumes play after
the muting and you hear a beep.
To recall a station: Select the desired
memory bank and press the relevant
preset button briefly.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Extra function of preset buttons
To store and recall a PTY programme
type.
When PTY is active (“PTY” lights up in
the display), you can store and recall
one programme type on/from each
preset button on FM.
=
/
Preset Scan
To switch the tape side: Press briefly.
To eject the tape: Press for approxi-
mately 1 sec.
Preset Scan cannot be started unless
PTY has been switched off (“PTY”
does not light up in the display).
Press SC for approximately 1 second
until you hear a beep.
“SCAN” will alternate with the name or
frequency of the scanned station in the
display.
Extra function
Frequency display during radio opera-
tion:
Press button briefly.
The frequency will be briefly displayed.
/
; SRC (Source)
The unit will scan all of the stations
stored on the preset buttons of the se-
lected memory bank/waveband.
You can switch between the radio and
tape audio sources (if a tape is insert-
ed).
> Cassette loading slot
Insert the tape with side A or 1 facing
up, the open side showing to the right.
To stop Scan / Preset Scan:
Press SC once again.
< lo
To switch the seek tuning sensitivity
level:
Press button briefly.
? SC
PTY-Scan
PTY-Scan cannot be started unless
PTY is switched on (“PTY” lights up in
the display).
All of the stations for the programme
type selected will be scanned briefly.
Radio operation
If “lo” is displayed, the radio will only
pick up strong, local stations (normal
sensitivity).
If “lo” does not light up, the radio will
also pick up weaker, distant stations
(high sensitivity).
Scan
The scan function cannot be started
unless PTY has been switched off
(“PTY” does not light up in the
display).
Tape operation
Press SC briefly -
Extra function of lo button:
To switch between mono and stereo
reception:
Press button for approximately 1 sec.
(beep).
The scanned frequency or station
name will flash in the display. The dis-
play will show “FM SCAN” or
“AM SCAN” while searching for the
next station. The unit will scan all of
the receivable stations of the
selected memory bank/waveband.
Cassetten-Scan
Press SC.
“CC SCAN” will appear in the display.
All cassette titles will be scanned brief-
ly.
To stop cassette scan:
Press SC once again.
The selected condition will be briefly
displayed.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
@ PTY (Programme Type)
B AUD
Adjusts the treble and bass frequen-
Extra function AUD
In the PTY mode, the preset buttons
become programme type buttons. With
every preset you can select one pro-
gramme type, such as for example
NEWS, SPORT, POP MUSIC, EDU-
CATE, etc. With the << >> rocker
switch, it is possible to recall all of the
PTY programme types as long as the
PTY function has been activated
(“PTY” will light up in the display).
Loudness - When listening at a low
level, the Loudness function creates a
more natural sound by boosting
the low frequency range.
Loudness on/off: Press AUD for ap-
proximately 1 sec.
“LD” lights up in the display if the
Loudness function is switched on.
Please refer to chapter “DSC program-
ming” for more information on how to
program the Loudness boost.
cies.
Press AUD once and use the rocker
switch to adjust the settings.
Treble +
Treble –
Bass –
Bass +
Setting the balance (left/right) and
the fader (front/rear).
Press AUD twice:
A DSC (Direct Software Control)
Use the DSC function to customise
certain programmable, basic settings
to suit your personal needs and prefer-
ences. See chapter “DSC program-
ming” for more information.
Fader front
Fader rear
Balance left
Balance right
The settings selected will appear in the
display. The last setting will be stored
automatically.
Switching AUD off: Press the button
once again.
If no changes are made within 8 sec-
onds, the display will switch back to
the previous condition.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Important notes
Installation
Accessories
Precautions
If you would like to install your new car ster- Use accessories and spare parts approved
eo yourself or add other audio components by Blaupunkt only.
Before starting to use your new car radio,
please read the following information care-
fully.
to existing ones, then please read carefully
the enclosed instructions on installation and
ucts with this car radio:
connection.
You can use the following Blaupunkt prod-
Traffic safety
In order to ensure that the set operates prop-
Amplifier
Traffic safety always has the highest priori-
ty.
erly it is necessary that the positive power
All Blaupunkt amplifiers, the preamp-out
supply line is connected to the ignition and
cable 7 607 893 093 is required.
As the driver of a motor vehicle, it is your
responsibility to pay attention to the traffic
situation at all times. Never use your car
radio in a way that could distract you.
Please keep in mind that you travel a dis-
tance of 14 m per second at a speed of only
50 km/h.
the permanent +12 V lead.
Do not ground the loudspeaker outputs!
Remote control
With the infrared remote control RC 06 you
can control all of the important functions of
your car hi-fi system from the steering wheel.
Should the traffic situation become particu-
larly demanding, we advise you not to use
the radio.
Always make sure that you are still able to
hear any warning signals coming from out-
side of the vehicle, such as police or fire
engine sirens, so that you can react accord-
ingly.
Therefore, you should always select a mod-
erate volume for playing your car radio while
you are driving.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
KeyCard theft protection system
This car radio includes one KeyCard as If a wrong KeyCard is inserted, then “CARD
standard equipment, but it can also be op- ERR” followed by “WAIT” will appear in the
•
•
Press the DSC button and select
“LEARN KC” by pressing / .
erated with a second card.
display. In this case please do not make any
further adjustments.
Press << or >>.
If you have lost your KeyCard or if it was
The display will switch to “CHANGE”.
damaged, you can buy a new one from your The system will switch off by itself after ap-
specialised dealer. proximately 10 seconds.
•
Remove the first KeyCard and insert
the new one while “CHANGE” still ap-
pears in the display.
If you use two KeyCards, you can store the If another card type is inserted (e.g. phone
following functions individually for each card: or credit card), the display will show
After the display indication “READY” or
“LEARN KC”,
“WRONG KC” for approximately 2 seconds.
Bass, treble, balance and fader settings,
Loudness, TA (traffic announcement vol- Remove the wrong card and insert the cor-
ume), TA priority, AF, beep volume, mute rect KeyCard.
•
press DSC.
Now you can also use the new KeyCard to
operate your car stereo.
volume, lo or dx, PTY functions, RM ON/
OFF.
After the display indications “CARD ERR”
or “WRONG KC”:
A maximum of 2 cards can be used for the
set.
In addition, the settings which are activated
before you switch the radio off, such as the
waveband (only Bergamo RCR 148) and
station will also remained stored.
•
Press ON to turn on the set.
If you attempt to “train” a third one, the ac-
cess authorisation for the KeyCard not used
for the “training” process will be deleted au-
tomatically.
Removing the KeyCard
•
Pull out the KeyCard tongue and re-
move the card.
This ensures that you will find your basic
settings re-adjusted automatically as soon
as you have inserted your KeyCard.
Displaying the radio pass data
“Training” a second KeyCard/
Replacing a KeyCard
Using the KeyCard supplied with your set
you can have the radio pass data such as
the model name, product number (7 6..) and
serial number indicated on the display pan-
el.
Operating the unit
When the unit is operated with the first Key-
Card, you can “train” a second one which
can also be used with the set.
•
Turn on the set.
With the KeyCard tongue protruding
out of the unit, insert the KeyCard into
the slot with the contact area facing
up in the middle of the area.
Please refer to chapter “DSC programming
- READ KC”.
To “train” a second KeyCard:
•
Insert the first KeyCard and turn on the
set.
The car radio is now ready for operation.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the audio source
Short Additional Memory
(S.A.M.)
Optical indication of anti-theft
protection
Using the SRC button you can switch be-
tween radio and tape operation.
Tape operation is only available if a cassette
is inserted.
Using the second KeyCard to be purchased Flashing KeyCard tongue
at any specialised dealership, you can pro-
When the vehicle is stationary and the Key-
To switch to another source,
gram a short text by selecting the DSC menu
item READ KC. This text will be moved
through the display and might be the tele-
phone number of a car repair service or the
emergency call number of your auto club.
Any specialised dealer with the proper
equipment can program the desired text with
up to a maximum of 162 characters onto the
KeyCard.
Card removed, the KeyCard tongue can be
switched to flash for extra anti-theft securi-
ty.
For this it is necessary that the positive pow-
er supply line and the permanent +12 V lead
are connected such as described in the in-
stallation instructions.
•
press SRC briefly.
Be sure that “LED ON” is adjusted in the
DSC mode.
If required, please refer to chapter “DSC
programming - LED”.
Turn On Message (T.O.M.)
Using the second KeyCard to be purchased
at any specialised dealership, you can pro-
gram the unit to display a selected “Turn On
Message” after the set is switched on.
Any specialised dealer with the proper
equipment can program the desired text with
up to a maximum of 48 characters onto the
KeyCard.
Switching off the flashing light
If you would like to deactivate the flashing
tongue in general, select “LED OFF” in the
DSC menu.
Care of your KeyCard
In order to ensure that the KeyCard always
functions correctly, it is important for the
contacts to be free from any foreign parti-
cles. Avoid direct skin contact.
Each time you switch on your car radio us-
ing the second KeyCard, this text will ap-
pear in the display.
If necessary, clean the KeyCard contacts
using a cotton swab dipped in alcohol.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio operation with RDS (Radio Data System)
The Radio Data System offers you more If “SEARCH” appears in the display when If you leave the service area of the regional
convenience when listening to FM radio sta- switching on the radio or recalling one of the programme tuned into, or if you would like
tions.
stored frequencies, the unit is automatically to take advantage of the full RDS service,
More and more radio stations have begun searching for an alternative frequency.
to broadcast RDS information alongside “SEARCH” will disappear from the display
switch to “REG OFF”.
•
Press the AF button for approximately
their programmes.
when the alternative frequency has been
1 sec. until “REG OFF” appears.
As soon as a programme has been identi- found or after the frequency band has been
fied, the station name including a regional run through completely.
identifier, if applicable, will appear in the dis- If the reception quality of the selected pro-
play, for example, NDR1 NDS (regional pro- gramme becomes too bad:
If the REG function is active, “REG ON” will
be briefly displayed each time the radio is
switched on.
gramme in Lower Saxony, Germany).
When RDS is activated, the preset buttons
become programme buttons. You now know
exactly which programme you have tuned
into, making it easy to find the desired sta-
tion quickly.
•
Tune into another station.
Selecting a waveband
(only Bergamo RCR 148)
REG - regional programme
You can select between the following wave-
bands:
FM 87.5 - 108 MHz
MW 531 - 1602 kHz
LW 153 - 279 kHz
Certain radio programmes are split up at
times into regional programmes offering lo-
cal information. The 1st programme broad-
cast by NDR, for example, offers pro-
grammes with different contents in the north-
ern states of Germany Schleswig-Holstein,
Hamburg and Lower Saxony at certain times
of the day.
If you are listening to one regional pro- In the DSC menu you can deactivate the
gramme and move to an area where anoth- station selection on either MW or LW or for
er linked regional programme becomes both wavebands at the same time.
stronger, the unit will switch to that pro- This has the advantage that only the re-
But RDS offers you further advantages:
•
Press the BND button until the desired
AF - Alternative frequency
waveband shows on the display panel.
The AF (Alternative Frequency) function
makes sure that the strongest frequency of
the currently selected programme is always
tuned in automatically.
This function is activated when “AF” appears
in the display.
Note:
In order to switch this function on or off,
gramme.
quired bands will allow to be activated, so
If you wish to continue listening to the first that you must press the BND button less
•
press the AF button briefly.
programme,
press the AF button for approximately
often. For more information, please refer to
chapter “DSC programming - AM ON/OFF”.
While searching for the strongest reception
signal, the radio may switch to mute briefly.
•
1 sec.
“REG ON” appears in the display.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Station tuning
Manual tuning:
Changing the memory bank
•
Press << >>; the frequency will change
in short intervals in downwards or up-
wards direction.
Automatic tuning
/
You can shift between the memory banks I,
II and T in order to store stations and recall
them later.
The currently selected memory bank is in-
dicated in the display.
•
Press
cally search for the next station.
When keeping the upper or lower part
/
; the car radio will automati-
When holding the right or left part of the rock-
er switch depressed, the frequency scan is
speeded up.
/
of the rocker switch depressed, seek tuning
will speed up in upwards or downwards di-
rection.
•
Press the FMT or BND button as many
times until the desired memory bank
lights up in the display.
Scrolling through the broadcast-
ing networks (FM only)
You can use the << >> buttons to tune in Storing stations
stations of your reception area.
On FM, you can store six stations on the
preset buttons 1-6 for each of the memory
banks I, II and T.
On MW/LW, you can also store six stations
each. (only Bergamo RCR 148)
If several programmes of the broadcasting
networks can be received, you can scroll
through them in forwards direction pressing
>>, or backwards using the << button, e.g.
NDR 1, 2, 3, 4, N-JOY.
For this it is necessary that the stations have
been tuned in at least once and that “AF” is
active (lights up in the display).
Seek tuning
Up
Down
•
•
Select the desired memory bank.
<< / >> Up/Down in short intervals
(FM only, “AF” must be switched off)
Tune in a station with the rocker switch
(either automatically
<< >>).
/
or manually
For this purpose, start automatic tuning, e.g.
using Travelstore:
Manual tuning with << >>
•
Press and hold down the desired pre-
set button until the radio resumes play
after the muting (takes approximately 1
sec., confirmed by beep).
You can also tune in a station manually.
•
Press FMT or BND for 1 sec.; the
system starts to run through the fre-
quency band. The display shows
“T-STORE”.
Condition:
AF and PTY must be switched off (i.e. the
symbols do not light up in the display).
Now the station has been stored.
If “AF” does not light up,
press AF.
If necessary, deactivate these functions:
The activated preset button is indicated in
the display.
•
•
Press AF or PTY briefly.
This fulfils the requirements for selecting
stations with << >>.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice:
Recalling stored stations
Scanning stations with Radio-
Scan
Should you tune in a station which has al-
ready been stored before, then the corre-
sponding preset position and memory bank
will briefly flash in the display.
You can recall any stored station at the touch
of a button.
You can briefly scan through all of the re-
ceivable stations of the selected waveband.
•
Select the memory bank with FMT or
BND.
To start the Scan function:
•
Press the corresponding preset button
briefly to recall the station.
•
Press SC briefly.
Automatically storing the
strongest stations with Travel-
store
The scanned frequency or station name will
flash in the display. During the actual scan-
ning process “FM SCAN” or “AM SCAN” will
be displayed.
Scanning stored stations with
Preset Scan
You can automatically store the six most
powerful FM stations of your current recep-
tion area sorted according to their signal
To select a scanned station and switch
off Radio-Scan:
You can have all of the stored stations briefly
strength. This function is particularly conven- scanned on all wavebands.
ient on longer trips.
•
Press SC briefly.
Preset Scan cannot be started unless PTY
has been switched off (“PTY” is not lit up in
the display).
If no station is selected, the scan function
will be automatically switched off after the
frequency band has been run through com-
pletely. The unit will tune in the station lis-
tened to before starting the scan.
•
Press the FMT or BND button for
1 sec.
“T-STORE” will appear in the display.
•
If necessary, press PTY.
To start Preset Scan:
Press SC for approximately 1 seconds.
The six strongest FM stations will be auto-
matically stored on the memory bank “T”
(Travelstore). When this process has been
completed, the radio will play the first sta-
tion stored on preset 1.
If desired, stations can also be stored man-
ually on the Travelstore bank (see “Storing
stations”).
•
All of the stored stations on the selected
waveband will be scanned one after the oth-
er. In the display “SCAN” will alternate with
the flashing station name or frequency.
Selecting the seek tuning sensi-
tivity
You can alter the automatic seek tuning
sensitivity.
If “lo” is displayed, the radio will only pick up
strong, local stations.
If “lo” does not light up, the radio will also
pick up weaker, distant stations.
To select a scanned station and switch
off Preset Scan:
•
Press SC briefly.
Note:
To switch the seek tuning sensitivity:
•
If “TA” shows on the display panel, the sys-
tem will scan the stored traffic stations only.
Press lo briefly.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
The sensitivity level can be altered sepa- PTY – Programme-Type
The letters printed in bold are identical to
the actual short-time indication in the dis-
play.
rately in both modes. Please refer to chap-
PTY is an RDS service offered by more and
ter “DSC programming - S-LO, S-DX”).
more radio broadcasters. This feature allows
you to select FM stations according to their
programme type. After you have chosen the
PTY of your preference, the corresponding
stations can be selected either by seek tun-
ing or using the scan function.
NEWS
Switching from stereo to mono
CURRENT AFFAIRS
INFORMATION
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP MUSIC
ROCK MUSIC
M.O.R. M (middle of the road music)
LIGHT M (light classical)
CLASSICS (serious classical)
OTHER M (other music)
WEATHER
Every time the radio is switched on, stereo
playback is activated automatically.
The unit will gradually switch to mono if re-
ception is poor.
You can also switch between mono and ster-
eo reception manually:
Switching PTY on/off
•
Press PTY.
•
Press the lo button for approximately
1 sec.
When the function is active, the programme
type selected last will briefly appear in the
display. “PTY” will be permanently indicat-
ed in the lower right corner of the display
panel.
The selected condition will briefly appear in
the display.
Loudness
Programme type
Adjusts the low bass frequencies for a more
natural sound.
FINANCE
Use << >> to have the last selected pro-
gramme type displayed and to choose a new
one.
You can select any one of the stored types
with the preset buttons 1-6.
Condition: PTY must be active.
Using DSC you can choose between Ger-
man and English (see “DSC programming -
PTY LANG”).
CHILDREN’S PROGRAMMES
SOCIAL AFFAIRS
RELIGION
PHONE IN
TRAVEL
HOBBIES
JAZZ MUSIC
COUNTRY MUSIC
NATIONAL MUSIC
OLDIES MUSIC
Switching Loudness on/off:
•
Press the AUD button for approximate-
ly 1 sec.
When the Loudness function is active, “LD”
will light up in the display.
See chapter “DSC programming” for more
information.
All of the programme types listed below are
available.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLK MUSIC
DOCUMENTARY
ALARM TEST (for service only)
•
press
/
to start seek tuning.
will be released. The station received be-
fore starting seek tuning will be tuned in.
If the system is unable to find a station of-
fering the selected programme type, the dis-
play will show “NO PTY” and a beep tone
will be released. The station received be-
fore starting seek tuning will be tuned in.
You can assign different programme types
to each preset position. Please refer to chap-
ter “Storing programme types”.
Storing programme types
Checking the programme type of the
station
At the factory, one programme type was
assigned to each of the preset buttons 1-6.
If desired, you can also store other availa-
ble programme types.
To do so, make sure that “PTY” lights up in
the display.
•
Press PTY for approximately 1 sec.
After the beep tone the display will show the
programme type offered by the tuned in sta-
tion.
If “NONE” appears in the display, the cur-
rent station has no PTY code.
b) Using the << >> buttons of the rocker
switch
•
•
•
If necessary, press the PTY button to
switch on the function.
When PTY is switched on, you can se-
lect a programme type using buttons
<< >>.
Select a programme type using but-
tons << >> and
Displaying the selected programme
type
hold down the desired preset button
(1-6) until you hear a beep.
•
•
•
Press << or >>; the programme
type selected last will be displayed
for 3 seconds.
•
Press << or >>.
The programme type selected last will be
displayed briefly.
Now the selected programme type can be
recalled by pressing this preset. For this, the
PTY function must be active.
During this period press >> (for-
wards) or << (backwards) to select
the desired type.
Selecting a programme type
Scanning stations with PTY-SCAN
a) Using the preset buttons
Press << or >> as many times as
required.
Condition: “PTY” must appear in the display.
When PTY is switched on, you can use
the preset buttons 1-6 to select the
programme types stored at the factory.
•
Press the SC button.
If you wish to listen to a station offering
the selected PTY,
All of the received stations offering the se-
lected programme type will be scanned.
•
Press one of the presets 1-6.
•
press
/
to start seek tuning.
The selected programme type will be
displayed for 2 seconds.
To switch off PTY-SCAN:
If the system is unable to find a station of-
fering the selected programme type, the dis-
play will show “NO PTY” and a beep tone
•
Press SC once again.
If you wish to listen to a station with
this PTY,
37
Download from Www.Somanuals.com. All Manuals Search And Download.
PTY priority
-
The system will switch to the linked
NDR2 station for the duration of the
“POP” programme.
Situation:
PTY is switched on and lights up in the dis-
play.
No station offering the selected programme
type can be currently received (neither with
seek tuning nor with scan).
During tape operation, the set will also au-
tomatically switch to the programme offer-
ing the selected PTY within the broadcast-
ing network.
After the PTY programme the system will
remain in the radio mode.
The set will switch back to the previous sta-
tion.
As soon as a programme with such PTY can
be received within the broadcasting network,
the unit will switch over to the correspond-
ing station for the duration of the pro-
gramme.
Notice:
As mentioned earlier, these functions are
currently only supported by a limited number
of RDS stations.
Example: German broadcasting network
NDR:
-
-
-
-
-
Station tuned in: NDR3.
“PTY” lights up in the display.
Programme type “POP” selected.
Seek tuning is started.
No station with “PTY-POP” can be
found.
-
-
-
The display shows “NO PTY” and
automatically switches back to NDR3.
NDR2 airs a “PTY-POP” programme.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving traffic programme stations with RDS-EON
The abbreviation “EON” stands for En- Traffic announcement priority
hanced Other Networks, meaning the ex- on/off
Switching off the beep tone
a) Tune into another station offering traf-
fic information:
change of information within a radio network.
If the priority for traffic announcement pro-
Many FM broadcasters offer traffic messag-
grammes is activated, “TA” will light up in
es for their service area at regular intervals.
the display.
•
•
Press the rocker switch or
press a preset button which has a
traffic programme station allocated
to it.
All traffic programme stations transmit a
special carrier signal alongside their pro-
To switch the priority on or off:
•
Press the TA button.
grammes, which is decoded by your car ra-
dio. If this signal is identified, “TP” will ap- When pressing TA while a message is be-
Alternatively:
pear in the display (Traffic Programme).
In addition to these, there are also stations
ing broadcast, this message will be inter-
rupted. The unit will then switch back to the
b) Switch off the priority for traffic an-
nouncements:
which do not actually transmit traffic pro- previous condition. The priority for all other
grammes themselves, but by using RDS- traffic messages remains active.
•
Press TA.
“TA” will disappear from the display.
EON they offer the possibility to receive the
Please note that several buttons have no
traffic messages broadcast by another traf- function while a traffic announcement is
fic programme station in the same radio broadcast.
network.
Automatic seek tuning start
(tape operation)
If you wish to have the priority for traffic an-
nouncements activated while listening to
one of these stations (e.g. NDR3), “TA” must
appear on the display panel.
If a traffic announcement is broadcast, the
radio will automatically switch to the linked
traffic programme station (in this case,
NDR2) for the duration of the message and
return to the original programme (NDR3)
afterwards.
Beep tone
When leaving the reception area of the tuned
in traffic programme station while listening
to a tape, the system will automatically start
searching for a new TA programme.
If no such station is found within approxi-
mately 30 seconds, you will hear a warning
beep every 30 seconds. To switch off the
beep tone proceed as described above.
If you leave the reception area of the traffic
programme station currently tuned into, you
will hear a beep tone approximately every
30 seconds.
This tone will also be released when press-
ing a preset button which has no traffic pro-
gramme allocated to it.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape operation
Adjusting the volume for traffic
announcements and the beep
tone
Fast Forward/Rewind
The car stereo has to be switched on.
The unit will automatically switch to tape
operation when inserting a cassette.
This volume was preset at the factory,
though you can alter the value using the
DSC function (see “DSC programming, TA
VOL”).
If the volume level is altered while a mes-
sage is being played, this will only affect the
current announcement.
Inserting a tape
•
•
Turn on the set.
Insert a tape.
>>
<<
Fast forward
Fast rewind
The cassette will be automatically transport-
ed to the playback position. Side A or 1 starts
to play.
/
Title selection (CPS)
During tape operation, “TR 1” or “TR 2”
(track) will be indicated on the display pan-
el.
Up
Down
Stop function by pressing
.
Insert the tape with side A or 1 facing up, the open side
showing to the right.
Selecting titles with CPS
(Cassette Programme Search)
Use this function to skip ( ) and repeat ( )
recorded titles.
To start CPS:
Removing a tape
•
Press / .
In order for CPS to function properly, there
has to be an unrecorded tape portion of at
least 3 seconds between the individual ti-
tles.
•
Press
The cassette will eject.
for 1 sec.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the tape side
(autoreverse)
Scanning cassette titles with
SCAN
Care notes
To avoid possible problems, we recommend
To change the tape direction during cassette You can have the cassette titles played brief- you to use C-60/C-90 type cassette tapes
playback:
Press
At the end of a tape side the mechanism
changes directions automatically to play the To start/stop the scan function:
ly by using the scan function. If you like a only. Store your tapes in a cool place away
title, stop the scan to continue listening to from dirt, dust and temperatures exceeding
•
briefly.
that track.
50 °Celsius. Allow very cold tapes to warm
up before playing them in order to avoid
uneven tape transport. After approximately
100 hours of use, dust particles collected
on the playback head or roller may lead to
tape run problems and sound distortions.
Use a head cleaning tape to remove nor-
mal dirt build-up. For tougher cases, use a
cotton swab (Q-Tip) dipped in alcohol. Do
not attempt to clean by inserting a hard ob-
ject into the player!
other side (autoreverse). The display shows
“TR 1” for track (side) 1 or “TR 2” for track 2.
•
Press the SC button briefly.
Scan condition: There has to be an unre-
corded tape portion of at least 3 seconds
between the individual titles.
Notice:
If there is too much tension on the tape dur-
ing playback, the set may switch over by it-
self before having reached the end of the
tape side. In this case check the condition
of the cassette tape. Sometimes it helps to
rewind it completely.
Listening to the radio during
fast tape winding with RM
(Radio Monitor)
When the tape is fast forwarded or rewound
(also with CPS), the radio will normally be
muted. In order to listen to the radio during
fast winding, you can activate the Radio
Tape equalisation
When a metal or CrO2 tape is inserted, the Monitor function.
tape mechanism automatically adjusts to For more information please refer to chap-
metal/CrO2 tape equalisation.
ter “DSC programming - RM ON/OFF”.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
DSC programming
AM ON / OFF (Bergamo RCR 148)
You can deactivate one or
both AM bands (MW/LW) in
order to reduce the number
of bands for selection with
BND.
TA VOL
To adjust the traffic an-
nouncement and beep tone
volume from between 0 to
63.
The message will then come
through at this volume, if the
volume adjusted for the pro-
gram is lower.
If the program volume is
higher than the TA VOL lev-
el, the traffic report will be
played slightly louder.
DSC (Direct Software Control) allows you
to customise certain programmable, basic
settings to suit your personal needs and
preferences and then store them.
The basic settings for this audio equipment
were made at the factory.
In the following you can find an overview of
these settings, so that you can always reset
to these if desired.
selectable:
AM ON – all bands
MW OFF – LW, FM
LW OFF – MW, FM
AM OFF – FM
If you wish to alter any of the programming,
•
press SRC to select one of the operat-
ing modes radio or cassette (e.g. ra-
dio, if you wish to change the language
with PTY LANG).
RM ON / OFF (Radio Monitor)
Allows you to listen to the
radio during fast winding of
the tape.
BEEP
Acknowledgement tone for
all functions which require a
button to be pressed for
more than 1 second.
The volume can be adjusted
from between 0 to 9. (0 =
off)
•
press DSC.
Use the rocker switch to select and adjust
the functions described in the following. The
display will show you the adjusted condition.
RM ON – Radio playback
activated
RM OFF – Function deacti-
vated
LOUDNESS When listening at a low lev-
el, the Loudness function
creates a more natural
sound by boosting the low
frequency range.
LED ON/OFF You can choose between
LED ON or LED OFF. With
LED ON, the KeyCard
tongue will flash for extra
anti-theft protection when
the unit has been switched
off and the KeyCard re-
moved.
/
Select function
Adjust/recall value
<< >>
LOUD 1 - Low boost
LOUD 6 - Max. boost
42
Download from Www.Somanuals.com. All Manuals Search And Download.
LEARN KC To “train” a second Key-
Card.
S-DX
S-LO
To adjust the seek tuning
sensitivity for distant recep- tings
tion.
DX 1 - high sensitivity
DX 3 - low sensitivity
Overview of DSC factory set-
Please read the information
in chapter “KeyCard theft
protection system - Training
a second KeyCard”.
RM
OFF
LOUDNESS
3
TA VOL
BEEP
35
4
To adjust the seek tuning
sensitivity for local recep-
tion.
LO 1 - high sensitivity
LO 3 - low sensitivity
The seek tuning sensitivity
values can be set separately
for AM and FM.
LED
ON
READ KC
To read out the KeyCard
data.
LEARN KC
READ KC
PTY LANG
S - DX
-
-
The KeyCard supplied with
the radio is used to display
the model name, type
number (7 6..) and the serial
number.
ENGLISH
1
S - LO
1
VOL FIX
25
Using the second KeyCard
to be purchased at any spe-
cialised dealership it is pos-
sible to display the Short
Additional Memory (S.A.M.)
data entered by the dealer.
See chapter “Short Addition-
al Memory S.A.M.”.
(Bergamo RCR 148):
AM ON
VOL FIX
Use this function to select
the volume at which the ra-
dio is set when it is switched
on. Adjust the desired vol-
ume level with << >>. When
adjusted to “VOL 0”, the
system will come on with the
volume selected before
switching it off.
PTY LANG To select the programme
type language: DEUTSCH
or ENGLISH
To quit the DSC programming mode
and store the adjustment:
•
Press DSC.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Blaupunkt
telephone hotline
Amplifier
Output power:
4 x 23 W RMS power
acc. to DIN 45324 at
14.4 V
Address of the next service
centre in your vicinity
(only for Germany)
4 x 35 W max. power
Tuner
Wavebands:
If you would like to know the address of
the next Blaupunkt service centre of
your area without having our service list
at hand:
FM
:
87.5 – 108 MHz
(only Bergamo RCR 148)
MW
LW
531 – 1602 kHz
153 – 279 kHz
-
-
Find out your area code.
Then call the following chargeable
FM sensitivity:
0.9 µV at 26 dB signal-
to-noise ratio
phone number: 01 80 / 5 25 56 66.
-
Using the area code to be entered
you will be automatically given the
address and phone number of the
next Blaupunkt service centre. You
can also request this information
by fax.
FM frequency response:
30 - 16 000 Hz
Tape player
Frequency response:
30 - 18 000 Hz
Subject to modifications!
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Blaupunkt-Werke GmbH
Bosch Gruppe
10/97 Ts
K7/VKD 8 622 401 345
Download from Www.Somanuals.com. All Manuals Search And Download.
|