WCY 71032 HPTL
Washing Machine
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove transportation safety bolts by turning them
gently.
3. Attach the plastic covers supplied in the User Manual bag
into the holes on the rear panel. (P)
2 Installation
Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If
they are not, call a qualified technician and plumber to have
any necessary arrangements carried out.
Preparation of the location and electrical, tap water and
waste water installations at the place of installation is
C under customer's responsibility.
Keep the transportation safety bolts in a safe place to
reuse when the washing machine needs to be moved
C again in the future.
warning: Installation and electrical connections of
the product must be carried out by the Authorized
Never move the product without the transportation safety
B
Service Agent. Manufacturer shall not be held liable for
damages that may arise from procedures carried out by
unauthorized persons.
bolts properly fixed in place!
C
2.4 Connecting water supply
warning: Prior to installation, visually check if the product
The water supply pressure required to run the product is
has any defects on it. If so, do not have it installed.
between 1 to 10 bars (0.1 – 1 MPa). It is necessary to
A
C have 10 – 80 liters of water flowing from the fully open
Damaged products cause risks for your safety.
Make sure that the water inlet and discharge hoses
tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is
higher.
as well as the power cable are not folded, pinched or
C crushed while pushing the product into its place after
installation or cleaning procedures.
If you are going to use the double water-inlet product
as a single (cold) water-inlet unit, you must install the
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it on a
long pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product
on a solid and flat floor that has sufficient load carrying
capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature
may fall below 0ºC.
• Place the product at least 1 cm away from the edges of
other furniture.
C
supplied stopper to the hot water valve before operating
the product. (Applies for the products supplied with a
blind stopper group.)
warning: Models with a single water inlet should not be
connected to the hot water tap. In such a case the laundry
A
will get damaged or the product will switch to protection
mode and will not operate.
warning: Do not use old or used water inlet hoses on the
new product. It may cause stains on your laundry.
A
1. Connect the special hoses supplied with the product to
the water inlets on the product. Red hose (left) (max. 90
ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is
for cold water inlet.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
warning: Ensure that the cold and hot water connections
A Otherwise, your laundry will come out hot at the end of
are made correctly when installing the product.
the washing process and wear out.
2. Tighten all hose nuts by hand. Never use a tool when
tightening the nuts.
2.3 Removing the transportation locks
warning: Do not remove the transportation locks before
taking out the packaging reinforcement.
A
A will be damaged.
warning: Remove the transportation safety bolts before
operating the washing machine! Otherwise, the product
1. Loosen all the bolts with a suitable spanner until they
rotate freely (C).
3. Open the taps completely after making the hose
connection to check for water leaks at the connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
3 / 20 EN
points. If any leaks occur, turn off the tap and remove the
1. Loosen the lock nuts on the feet by hand.
nut. Retighten the nut carefully after checking the seal. To 2. Adjust the feet until the product stands level and
prevent water leakages and damages caused by them,
keep the taps closed when the machine is not in use.
balanced.
3. Tighten all lock nuts again by hand.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
warning: Your house will be flooded if the hose comes
out of its housing during water discharge. Moreover, there
A is risk of scalding due to high washing temperatures!
To prevent such situations and to ensure smooth water
intake and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come out.
warning: Do not use any tools to loosen the lock nuts.
Otherwise, they will get damaged.
A
• The hose should be attached to a height of at least 40
cm, and 100 cm at most.
• In case the hose is elevated after laying it on the floor
level or close to the ground (less than 40 cm above the
ground), water discharge becomes more difficult and the
laundry may come out excessively wet. Therefore, follow
the heights described in the figure.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a 16
A fuse. Our company shall not be liable for any damages
that will arise when the product is used without grounding in
accordance with the local regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• If the current value of the fuse or breaker in the house is
less than 16 Amps, have a qualified electrician install a
16 Amp fuse.
• The voltage specified in the "Technical specifications"
section must be equal to your mains voltage.
• Do not make connections via extension cables or multi-
plugs.
• To prevent flowing of dirty water back into the machine
and to allow for easy discharge, do not immerse the hose
end into the dirty water or do not drive it in the drain more
than 15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between
the drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may
not be longer than 3.2 m. To avoid water leak failures,
the connection between the extension hose and the
drain hose of the product must be fitted well with an
appropriate clamp as not to come off and leak.
warning: Damaged power cables must be replaced by
the Authorized Service Agents.
B
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product.
4. Install transportation safety bolts in the reverse order of
removal procedure;
Never move the product without the transportation safety
bolts properly fixed in place!
C
2.6 Adjusting the feet
warning: Packaging materials are dangerous to children.
Keep packaging materials in a safe place away from
A reach of the children.
warning: In order to ensure that the product operates
A balanced on its feet. Balance the machine by adjusting
more silently and vibration-free, it must stand level and
the feet. Otherwise, the product may move from its place
and cause crushing and vibration problems.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
4 / 20 EN
3.4 Initial use
3 Preparation
Before starting to use the product, make sure that all
preparations are made in accordance with the instructions in
sections “Important safety instructions” and “Installation”.
To prepare the product for washing laundry, perform first
operation in Drum Cleaning programme. If your product
is not equipped with Drum Cleaning programme, perform
the Initial Use procedure in accordance with the methods
described under “5.2 Cleaning the loading door and the
drum” section of the user manual.
3.1 Sorting the laundry
• Sort laundry according to type of fabric, colour, and
degree of soiling and allowable water temperature.
• Always obey the instructions given on the garment tags.
3.2 Preparing laundry for washing
• Laundry items with metal attachments such as,
underwired bras, belt buckles or metal buttons will
damage the machine. Remove the metal pieces or wash
the clothes by putting them in a laundry bag or pillow
case.
• Take out all substances in the pockets such as coins,
pens and paper clips, and turn pockets inside out and
brush. Such objects may damage the product or cause
noise problem.
• Put small size clothes such as infant's socks and nylon
stockings in a laundry bag or pillow case.
• Place curtains in without compressing them. Remove
curtain attachment items.
Use an anti-limescale suitable for the washing machines.
C
• Fasten zippers, sew loose buttons and mend rips and
tears.
Some water might have remained in the product due to
the quality control processes in the production. It is not
C harmful for the product.
• Wash “machine washable” or “hand washable” labeled
products only with an appropriate programme.
• Do not wash colours and whites together. New, dark
coloured cottons release a lot of dye. Wash them
separately.
• Tough stains must be treated properly before washing. If
unsure, check with a dry cleaner.
• Use only dyes/colour changers and limescale removers
suitable for machine wash. Always follow the instructions
on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer
for a few hours before washing. This will reduce pilling.
• Laundry that are subjected to materials such as flour,
lime dust, milk powder, etc. intensely must be shaken off
before placing into the machine. Such dusts and powders
on the laundry may build up on the inner parts of the
machine in time and can cause damage.
3.5 Correct load capacity
The maximum load capacity depends on the type of laundry,
the degree of soiling and the washing programme desired.
The machine automatically adjusts the amount of water
according to the weight of the loaded laundry.
warning: Follow the information in the “Programme
A washing performance will drop. Moreover, noise and
and consumption table”. When overloaded, machine's
vibration problems may occur.
Laundry type
Bathrobe
Weight (g)
1200
100
Napkin
Duvet cover
Bed Sheet
Pillowcase
Tablecloth
700
500
200
250
3.3 Things to be done for energy saving
Following information will help you use the product in an
ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed by
the programme you have selected, but do not overload;
see, "Programme and consumption table".
• Always follow the instructions on the detergent
packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly
soiled laundry.
• Do not use prewash and high temperatures for laundry
that is not heavily soiled or stained.
Towel
200
Hand towel
Evening gown
Underclothing
Men’s overalls
Men’s shirt
Men’s pajamas
Blouses
100
200
100
600
200
500
100
• If you plan to dry your laundry in a dryer, select the
highest spin speed recommended during washing
process.
• Do not use detergent in excess of the amount
recommended on the detergent package.
3.6 Loading the laundry
1. Open the loading door.
2. Place laundry items loosely into the machine.
3. Push the loading door to close until you hear a locking
sound. Ensure that no items are caught in the door.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
5 / 20 EN
Adjusting detergent amount
The loading door is locked while a programme is running.
The amount of washing detergent to be used depends
on the amount of laundry, the degree of soiling and water
hardness.
The door can only be opened a while after the programme
C comes to an end.
A
warning: In case of misplacing the laundry, noise and
• Do not use amounts exceeding the dosage quantities
recommended on the detergent package to avoid
problems of excessive foam, poor rinsing, financial
savings and finally, environmental protection.
• Use lesser detergent for small amounts or lightly soiled
clothes.
Using softeners
Pour the softener into the softener compartment of the
detergent drawer.
vibration problems may occur in the machine.
3.7 Using detergent and softener
When using detergent, softener, starch, fabric dye, bleach
or limescale remover read the manufacturer's instructions
C on the package carefully and follow the suggested dosage
values. Use measuring cup if available.
Detergent Drawer
The detergent drawer is composed of three compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener
compartment.
• Do not exceed the (>max<) level marking in the softener
compartment.
• If the softener has lost its fluidity, dilute it with water
before putting it in the detergent drawer.
Using liquid detergents
If the product contains a liquid detergent cup:
• Make sure that you have placed the liquid detergent cup
in compartment nr. "2".
3
1
2
• If the liquid detergent has lost its fluidity, dilute it with
water before putting in the detergent cup.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing
programme.
If the product does not contain a liquid detergent
cup:
• Never leave the detergent drawer open while the washing
programme is running!
• Do not use liquid detergent for the prewash in a
programme with prewash.
• When using a programme without prewash, do not
put any detergent into the prewash compartment
(compartment nr. "1").
• In a programme with prewash, do not put liquid detergent
into the prewash compartment (compartment nr. "1").
• Do not select a programme with prewash if you are using
a detergent bag or dispensing ball. Place the detergent
bag or the dispensing ball directly among the laundry in
the machine.
• If you are using liquid detergent, do not forget to place
the liquid detergent cup into the main wash compartment
(compartment nr. "2").
Choosing the detergent type
The type of detergent to be used depends on the type and
colour of the fabric.
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents
(liquid detergent, wool shampoo, etc.) used solely for
delicate clothes.
• When washing dark coloured clothes and quilts, it is
recommended to use liquid detergent.
• Wash woolens with special detergent made specifically
for woolens.
• Liquid detergent stains your clothes when used with
Delayed Start function. If you are going to use the Delayed
Start function, do not use liquid detergent.
Using gel and tablet detergent
Apply the following instructions when using tablet, gel and
similar detergents.
• If the gel detergent thickness is fluidal and your machine
does not contain a special liquid detergent cup, put the
gel detergent into the main wash detergent compartment
during first water intake. If your machine contains a liquid
detergent cup, fill the detergent into this cup before
starting the programme.
• If the gel detergent thickness is not fluidal or in the shape
of capsule liquid tablet, put it directly into the drum before
washing.
• Put tablet detergents into the main wash compartment
(compartment nr. "2") or directly into the drum before
washing.
Tablet detergents may leave residues in the detergent
compartment. If you encounter such a case, place the
C tablet detergent between the laundry, close to the lower
part of the drum in future washings.
warning: Use only detergents manufactured specifically
Use the tablet or gel detergent without selecting the
for washing machines.
A
A
prewash function.
C
warning: Do not use soap powder.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
6 / 20 EN
• Use just a little amount (approx. 50 ml) of bleaching agent
and rinse the clothes very well as it causes skin irritation.
Do not pour the bleaching agent onto the clothes and do
not use it for coloured clothes.
Using starch
• Add liquid starch, powder starch or the fabric dye into the
softener compartment.
• Do not use softener and starch together in a washing
cycle.
• When using oxygen based bleaches, select a programme
that washes at a lower temperature.
• Wipe the inside of the machine with a damp and clean
cloth after using starch.
• Oxygen based bleaches can be used together with
detergents; however, if its thickness is not the same
with the detergent, put the detergent first into the
compartment nr. "2" in the detergent drawer and wait
until the detergent flows while the machine is taking
in water. Add the bleaching agent from the same
compartment while the machine is still taking in water.
Using limescale remover
Using bleaches
• Select a programme with prewash and add the bleaching
agent at the beginning of the prewash. Do not put
detergent in the prewash compartment. As an alternative
application, select a programme with extra rinse and add
the bleaching agent while the machine is taking water
from the detergent compartment during first rinsing step.
• Do not use bleaching agent and detergent by mixing
them.
• When required, use limescale removers manufactured
specifically for washing machines only.
3.8 Tips for efficient washing
Light colours and whites
Clothes
Delicates/
Woolens/Silks
Colours
Dark colours
(Recommended
(Recommended
(Recommended temperature
range based on soiling level:
40-90ºC)
(Recommended temperature
range based on soiling level:
cold-40ºC)
temperature range
temperature range
based on soiling level: based on soiling level:
cold-40ºC)
cold-30ºC)
It may be necessary to pre-
treat the stains or perform
prewash. Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
heavily soiled clothes. It is
recommended to use powder
detergents to clean clay and
soil stains and the stains that
are sensitive to bleaches.
Powder and liquid
detergents recommended
for colours can be used at
dosages recommended for
heavily soiled clothes. It is
Prefer liquid
Liquid detergents
detergents produced
for delicate clothes.
Woolen and silk
Heavily Soiled
suitable for colours
and dark colours can
(difficult stains such
as grass, coffee,
fruits and blood.)
recommended to use powder be used at dosages
detergents to clean clay and recommended for
soil stains and the stains that heavily soiled clothes.
are sensitive to bleaches. Use
clothes must be
washed with special
woolen detergents.
detergents without bleach.
Prefer liquid
Powder and liquid detergents Liquid detergents
Powder and liquid detergents
recommended for whites
can be used at dosages
recommended for normally
soiled clothes.
detergents produced
for delicate clothes.
Woolen and silk
Normally Soiled
recommended for colours
can be used at dosages
recommended for normally
suitable for colours
and dark colours can
be used at dosages
(For example, stains
caused by body on
collars and cuffs)
clothes must be
washed with special
woolen detergents.
soiled clothes. Use detergents recommended for
without bleach. normally soiled clothes.
Prefer liquid
Powder and liquid detergents Liquid detergents
Powder and liquid detergents
recommended for whites
can be used at dosages
recommended for lightly soiled
clothes.
detergents produced
for delicate clothes.
Woolen and silk
recommended for colours
can be used at dosages
recommended for lightly
suitable for colours
and dark colours can
be used at dosages
Lightly Soiled
(No visible stains
exist.)
clothes must be
washed with special
woolen detergents.
soiled clothes. Use detergents recommended for lightly
without bleach.
soiled clothes.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
7 / 20 EN
4 Operating the product
4.1 Control panel
1
2
3
4
5
6
8
7
1 - Programme Selection knob (Uppermost position On/Off)
2 - Display
3 - Delayed Start button (in some models)
4 - Programme Follow-up indicator
5 - Start / Pause button
6 - Auxiliary Function buttons
7 - Spin Speed Adjustment button
8 - Temperature Adjustment button
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
8 / 20 EN
4.2 Preparing the machine
4.5 Additional programmes
Make sure that the hoses are connected tightly. Plug in your For special cases, additional programmes are available in
machine. Turn the tap on completely. Place the laundry in the the machine.
machine. Add detergent and fabric softener.
Additional programmes may differ according to the
model of the machine.
4.3 Programme selection
Select the programme suitable for the type, quantity
and soiling degree of the laundry in accordance with the
"Programme and consumption table" and the temperature
table below.
• Cotton Eco
You may wash your normally soiled durable cotton and
linen laundry in this programme with the highest energy
and water saving compared to all other wash programmes
suitable for cottons. Actual water temperature may differ
from the declared cycle temperature. Programme duration
may automatically be shortened during later stages of the
programme if you wash less amount (e.g. ½ capacity or
less) of laundry. In this case energy and water consumption
will be further decreased giving you the opportunity for a
more economical wash. This feature is available for certain
models having remaining time display.
Heavily soiled white cottons and linens. (coffee table
covers, tableclothes, towels, bed sheets, etc.)
90˚C
Normally soiled, coloured, fade proof linens, cottons
or synthetic clothes (shirt, nightgown, pajamas, etc.)
and lightly soiled white linens (underwear, etc.)
60˚C
40˚C-
Blended laundry including delicate textile (veil
30˚C- Cold curtains, etc.), synthetics and woolens.
Select the desired programme with the Programme
Selection button.
• Babyprotect+
Use this programme for your laundry for which you require
an anti-allergic and hygienic washing at high temperature
with intensive and long washing cycles.
Programmes are limited with the highest spin speed
appropriate for that particular type of fabric.
When selecting a programme, always consider the type
of fabric, colour, degree of soiling and permissible water
temperature.
Babyprotect+ 60°C programme is tested and approved
by “The British Allergy Foundation” (Allergy UK) in
United Kingdom.
Always select the lowest required temperature. Higher
temperature means higher power consumption.
• Delicate
Use this programme to wash your delicate clothes. It washes
with a gentle action without any interim spin compared to
the Synthetics programme.
For further programme details, see "Programme and
consumption table"
• Hand Wash 20°C
4.4 Main programmes
Use this programme to wash your woolen/delicate clothes
that bear “not machine- washable” tags and for which hand
wash is recommended. It washes laundry with a very gentle
washing action to not to damage clothes.
• Daily Xpress
Depending on the type of fabric, use the following main
programmes.
• Cotton
Use this programme for your cotton laundry (such as bed
sheets, duvet and pillowcase sets, towels, bathrobes,
underwear, etc.). Your laundry will be washed with vigorous
washing action for a longer washing cycle.
• Synthetics
Use this programme to wash your synthetic clothes (shirts,
blouses, synthetic/cotton blends, etc.). It washes with a
gentle action and has a shorter washing cycle compared to
the Cottons programme.
Use this programme to quickly wash your little amount of
lightly soiled cotton clothes.
• Xpress Super Short
Use this programme to wash your little amount of lightly
soiled cotton clothes in a short time.
• Dark Care
Use this programme to wash your dark coloured laundry, or
the coloured laundry that you do not want them get faded.
Washing is performed with less mechanical movements at
low temperature. It is recommended to use liquid detergent
or wool shampoo for dark coloured laundry.
• Mix 40
For curtains and tulle, use the Synthetic 40˚C programme
with prewash and anti-creasing functions selected. As their
meshed texture causes excessive foaming, wash the veils/
tulle by putting little amount of detergent into the main
wash compartment. Do not put detergent in the prewash
compartment.
Use this programme to wash your cotton and synthetic
clothes together without sorting them.
• Woollen
Use this programme to wash your woolen clothes. Select
the appropriate temperature complying with the tags of your
clothes. Use appropriate detergents for woolens.
• Shirts
Use this programme to wash the shirts made of cotton,
synthetic and synthetic blended fabrics together.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
9 / 20 EN
4.6 Special programmes
For specific applications, select any of the following
programmes.
• Rinse
Use this programme when you want to rinse or starch
separately.
• Spin+Drain
Use this programme to apply an additional spin cycle for
your laundry or to drain the water in the machine.
Before selecting this programme, select the desired spin
speed and press Start / Pause button. First, the machine will
drain the water inside of it. Then, it will spin the laundry with
the set spin speed and drain the water coming out of them.
If you wish to drain only the water without spinning your
laundry, select the Pump+Spin programme and then select
the No Spin function with the help of Spin Speed Adjustment
button. Press Start / Pause button.
C Use a lower spin speed for delicate laundries.
4.7 Temperature selection
Whenever a new programme is selected, the recommended
temperature for the selected programme appears on the
temperature indicator.
To decrease the temperature, press the Temperature
Adjustment button. Temperature will decrease gradually.
If the programme has not reached the heating step,
you can change the temperature without switching the
C machine to Pause mode.
4.8 Spin speed selection
Whenever a new programme is selected, the recommended
spin speed of the selected programme is displayed on the
spin speed indicator.
To decrease the spin speed, press the Spin Speed
Adjustment button. Spin speed decreases gradually. Then,
depending on the model of the product, "Rinse Hold" and
"No Spin" options appear on the display. See "Auxiliary
function selection" section for explanations of these options.
If the programme has not reached the spinning step, you
can change the speed without switching the machine to
C Pause mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
10 / 20 EN
4.9 Programme and consumption table
EN
Auxiliary functions
Programme
Temperature
Cotton
Cotton
Cotton
90
60
40
7
7
7
147
118
98
74
70
69
2.30 1600
1.54 1600
0.85 1600
•
•
•
•
•
•
•
•
•
•
•
•
Cold-90
Cold-90
Cold-90
40-60
Cotton Eco
Cotton Eco
Cotton Eco
Babyprotect+
Xpress Super Short
Daily Xpress
Daily Xpress
60**
60**
40**
90
7
160
145
130
165
14
44 1.175 1600
38 0.934 1600
3.5
3.5
7
40-60
38
90
50
60
60
60
66
43
55
67
55
55
47
60
34
0.826 1600
2.40 1600
0.11 1400
1.90 1400
1.00 1400
0.25 1400
0.55 800
0.23 600
0.60 800
0.58 800
1.00 800
0.55 800
0.34 600
1.00 600
0.20 600
40-60
•
*
30-90
30
2
•
•
•
•
*
Cold-30
Cold-90
Cold-90
Cold-90
Cold-40
Cold-40
Cold-40
Cold-40
Cold-60
Cold-60
Cold-40
Cold-60
20
90
7
88
60
7
58
Daily Xpress
Dark Care
Delicate
30
7
28
40
3.5
2
107
59
30
•
•
•
•
•
•
•
•
•
•
•
•
Mix 40
Sports
Synthetics
Synthetics
Woollen
40
40
60
40
3.5
4
3
115
101
116
106
60
•
•
•
•
•
•
•
•
3
40
1.5
3.5
1
Shirts
60
104
43
•
•
*
Hand Wash 20°C
20
• Selectable
* Automatically selected, no canceling.
** Energy Label programme (EN 60456 Ed.3)
** “Cotton Economic 40°C and Cotton Economic 60°C are the standard programmes.”These programmes are referred to as ‘standard 40°C
cotton programme’ and ‘standard 60°C cotton programme’
*** If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed.
The auxiliary functions in the table may vary according to the model of your machine.
Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient
temperature, type and amount of laundry, selection of auxiliary functions and spin speed, and changes in electric voltage.
You can see the washing time of the programme you have selected on the display of the machine. It is normal that small
differences may occur between the time shown on the display and the real washing time.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
11 / 20 EN
4.10 Auxiliary function selection
Use the following auxiliary functions according to your
daily needs. Select the desired auxiliary functions before
starting the programme. Furthermore, you may also select
or cancel auxiliary functions that are suitable to the running
programme without pressing the Start / Pause button when
the machine is operating. For this, the machine must be in
a step before the auxiliary function you are going to select
or cancel.
prevent them from getting wrinkled when there is no water
in the machine. Press Start / Pause button after this process
if you want to drain the water without spinning your laundry.
Programme will resume and complete after draining the water.
If you want to spin the laundry held in water, adjust the Spin
Speed and press Start / Pause button.
The programme resumes. Water is drained, laundry is spun
and the programme is completed.
If the auxiliary function cannot be selected or canceled, light
of the relevant auxiliary function will blink 3 times to warn
the user.
Delayed Start
With the Delayed Start function the startup of the programme
may be delayed up to 19 hours. Delayed start time can be
increased by increments of 1 hour.
Some functions cannot be selected together. If a second
auxiliary function conflicting with the first one is selected
before starting the machine, the function selected
first will be canceled and the second auxiliary function
selection will remain active. For example, if you want to
select Quick Wash after you have selected the Prewash,
Prewash will be canceled and Quick Wash will remain
active.
Do not use liquid detergents when you set Delayed Start!
There is the risk of staining of the clothes.
Open the loading door, place the laundry and put detergent,
etc.Select the washing programme,temperature, spin speed
and, if required, the auxiliary functions. Set the desired time
by pressing the Delayed Start button. Press Start / Pause button.
The delayed start time you have set is displayed. Delayed start
countdown starts. “_”symbol next to the delayed start time
moves up and down on the display.
An auxiliary function that is not compatible with the
programme cannot be selected. (See “Programme and
consumption table”)
Auxiliary Function buttons may vary according to the
model of the machine.
Additional laundry may be loaded during the delayed
start period.
• Pre-wash
A Prewash is only worthwhile for heavily soiled laundry. Not
using the Prewash will save energy, water, detergent and
time.
At the end of the countdown, duration of the selected
programme will be displayed. “_” symbol will disappear and
the selected programme will start.
Prewash without detergent is recommended for tulle
and curtains.
Changing the Delayed Start period
Press Delayed Start button. Every time the button is pressed,
the period will change in 3-hour increments and the light of
the selected delayed start time will turn on.
• Quick Wash
This function can be used in Cottons and Synthetics
programmes. It decreases the washing times and also the
number of rinsing steps for lightly soiled laundry.
Canceling the Delayed Start function
If you want to cancel the delayed start countdown and start
the programme immediately:
Set the Delayed Start period to zero (all delayed start period
lights will turn off) or turn the Programme Selection knob
to any programme. Thus, Delayed Start function will be
canceled. The End/Cancel light flashes continuously. Then,
select the programme you want to run again. Press Start /
Pause button to start the programme.
When you select this function, load your machine with
half of the maximum laundry specified in the programme
table.
• Extra Rinse
This function enables the machine to make another rinsing
in addition to the one already made after the main wash.
Thus, the risk for sensitive skins (babies, allergic skins, etc.)
to be effected by the minimal detergent remnants on the
laundry can be reduced.
4.11 Starting the programme
Press Start / Pause button to start the programme.
Programme follow-up light showing the startup of the
programme will turn on.
• Pet hair removal
This function helps to remove pet hair that remain on your garments
more effectively.When you select this function, Prewash and Extra
Rinse steps are added to the normal programme. Thus, washing is
performed with more water (30%) and the pet hair is removed more
effectively.
If no programme is started or no key is pressed within
1 minute during programme selection process, the
machine will switch to Pause mode and the illumination
level of the temperature, speed and loading door
indicator lights will decrease. Other indicator lights and
indicators will turn off. Once the Programme Selection
knob is rotated or any button is pressed, indicator lights
and indicators will turn on again.
Never wash your pets in the washing machine.
• Rinse Hold
4.12 Child Lock
If you are not going to unload your clothes immediately after
the programme completes, you may use rinse hold function
to keep your laundry in the final rinsing water in order to
Use child lock function to prevent children from tampering
with the machine. Thus you can avoid any changes in a
running programme.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
12 / 20 EN
the Loading Door while the Loading Door light is off, you
have to cancel the current programme; see "Canceling the
programme".
If the Programme Selection knob is turned when the
Child Lock is active, “Con” appears on the display.
C The Child Lock does not allow any change in the
programmes and the selected temperature, speed and
Changing the selections after
programme has started
auxiliary functions.
Even if another programme is selected with the
Programme Selection knob while the Child Lock is
C active, previously selected programme will continue
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to
pause mode while a programme is running. The light of
the step which the machine is in starts flashing in the
Programme Follow-up indicator to show that the machine
has been switched to the pause mode.
running.
When the Child Lock is active and the machine is
running, you can switch the machine to Pause mode
C without deactivating the Child Lock by turning the
Also, when the loading door is ready to be opened, Loading
Door light will also illuminate continuously in addition to the
programme step light.
Programme Selection knob to On / Off position. When
you turn the Programme Selection knob afterwards, the
programme will resu
Changing the speed and temperature settings for
auxiliary functions
To activate the Child Lock:
Depending on the step the programme has reached, you
may cancel or activate the auxiliary functions; see, "Auxiliary
function selection".
Press and hold 1st and 2nd Auxiliary Function buttons for
3 seconds. The lights on the 1st and 2nd Auxiliary Function
buttons will flash while you keep the buttons pressed for 3
seconds.
You may also change the speed and temperature settings;
see, "Spin speed selection" and "Temperature selection".
To deactivate the Child Lock:
Press and hold 1st and 2nd auxiliary function buttons for 3
seconds while any programme is running. The lights on the
1st and 2nd Auxiliary Function buttons will flash while you
keep the buttons pressed for 3 seconds.
If no change is allowed, the relevant light will flash for
3 times.
C
4.15 Adding or taking out laundry
In addition to the method above, to deactivate the Child
Lock, switch the Programme Selection knob to On /
C Off position when no programme is running, and select
Press the Start / Pause button to switch the machine to
pause mode. The programme follow-up light of the relevant
step during which the machine was switched into the pause
mode will flash. Wait until the Loading Door can be opened.
Open the Loading Door and add or take out the laundry.
Close the Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press Start /
Pause button to start the machine.
another programme.
When the power is restored after a power failure or after
your machine is unplugged and plugged in again, the
C Child Lock will not be deactivated when the machine
resumes operating.
4.13 Progress of programme
4.16 Canceling the programme
Progress of a running programme can be followed from the
Programme Follow-up indicator. At the beginning of every
programme step, the relevant indicator light will turn on and
light of the completed step will turn off.
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme
will be canceled. End / Cancel light will flash continuously to
notify that the programme has been canceled.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme flow
while the programme is running. To do this, the change
you are going to make must be in a step after the running
programme step. If the change is not compatible, relevant
lights will flash for 3 times.
Your machine will end the programme when you turn the
Programme Selection knob; however, it does not drain the
water inside. When you select and start a new programme,
the newly selected programme will start depending on the
step the previous programme was canceled in. For example,
it may take in additional water or continue to wash with the
water inside.
Depending on the step where the programme was
canceled in, you may have to put detergent and softener
C again for the programme you have selected anew.
If the machine does not pass to the spinning step,
Rinse Hold function might be active or the automatic
C unbalanced load detection system might be activated
due to the unbalanced distribution of the laundry in the
machine.
4.14 Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases when
the water level is unsuitable.
Loading door light will start flashing when the machine
is switched to Pause mode. Machine checks the level of
the water inside. If the level is suitable, Loading Door light
illuminates steadily within 1-2 minutes and the loading door
can be opened.
If the level is unsuitable, Loading Door light turns off and the
loading door cannot be opened. If you are obliged to open
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
13 / 20 EN
5 Maintenance and cleaning
Repeat Drum Cleaning process in every 2 months.
Service life of the product extends and frequently faced
problems decrease if cleaned at regular intervals.
C
C
5.1 Cleaning the detergent drawer
Use an anti-limescale suitable for the washing machines.
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
After every washing make sure that no foreign substance is
left in the drum.
1. Press the dotted point on the siphon in the softener
compartment and pull towards you until the compartment
is removed from the machine.
If the holes on the bellow shown in the figure is blocked,
If more than normal amount of water and softener
open the holes using a toothpick.
mixture starts to gather in the softener compartment, the
C siphon must be cleaned.
Foreign metal substances will cause rust stains in the
drum. Clean the stains on the drum surface by using
C cleaning agents for stainless steel. Never use steel wool
2. Wash the detergent drawer and the siphon with plenty of
lukewarm water in a washbasin. Wear protective gloves
or use an appropriate brush to avoid touching of the
residues in the drawer with your skin when cleaning.
3. Insert the drawer back into its place after cleaning and
make sure that it is seated well.
or wire wool.
warning: Never use sponge or scrub materials. These
will damage the painted and plastic surfaces.
A
5.3 Cleaning the body and control panel
Wipe the body of the machine with soapy water or non-
corrosive mild gel detergents as necessary, and dry with a
soft cloth.
If your detergent drawer is the one indicated in the following
figure:
Use only a soft and damp cloth to clean the control panel.
5.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the
rear of the machine and also at the end of each water intake
hose where they are connected to the tap. These filters
prevent foreign substances and dirt in the water to enter the
washing machine. Filters should be cleaned as they do get
dirty.
Lift the rear part of the siphon to remove it as illustrated.
After performing the above mentioned cleaning
C procedures, replace the siphon back to its seating and
push its front section downwards to make sure that the
locking tab engages.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate
in your machine in time and may cause unpleasant odours
and washing complaints. To avoid this, use the Drum
Cleaning programme. If your machine is not featured with
Drum Cleaning programme, use Cottons-90 programme
and select Additional Water or Extra Rinse auxiliary
functions as well. Run the programme without any laundry in
the machine. Before starting the programme, put max. 100
g of powder anti-limescale into the main wash detergent
compartment (compartment nr. 2). If the anti-limescale is in
tablet form, put only one tablet into compartment nr. 2. Dry
the inside of the bellow with a clean piece of cloth after the
programme has come to an end.
1. Close the taps.
2. Remove the nuts of the water intake hoses to access
the filters on the water intake valves. Clean them with an
appropriate brush. If the filters are too dirty, take them out
by means of pliers and clean them.
3. Take out the filters on the flat ends of the water intake
hoses together with the gaskets and clean thoroughly
under running water.
4. Replace the gaskets and filters carefully in their places
and tighten the hose nuts by hand.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
14 / 20 EN
Discharging the water when the product has an emergency
draining hose:
5.5 Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents solid items
such as buttons, coins and fabric fibers clogging the pump
impeller during discharge of washing water. Thus, the water
will be discharged without any problem and the service life
of the pump will extend.
If the machine fails to drain water, the pump filter is clogged.
Filter must be cleaned whenever it is clogged or in every 3
months. Water must be drained off first to clean the pump
filter.
In addition, prior to transporting the machine (e.g., when
moving to another house) and in case of freezing of the
water, water may have to be drained completely.
a. Pull the emergency draining hose out from its seat
b. Place a large container at the end of the hose. Drain the
water into the container by pulling out the plug at the end
of the hose. When the container is full, block the inlet
of the hose by replacing the plug. After the container is
emptied, repeat the above procedure to drain the water in
the machine completely.
warning: Foreign substances left in the pump filter may
damage your machine or may cause noise problem.
A
In order to clean the dirty filter and discharge the water:
1. Unplug the machine to cut off the supply power.
c. When draining of water is finished, close the end by the
plug again and fix the hose in its place.
d. Turn the pump filter to take it out.
Discharging the water when the product does not have an
emergency draining hose:
warning: Temperature of the water inside the machine
A cleaned after the water in the machine cools down.
may rise up to 90 ºC. To avoid burning risk, filter must be
2. Open the filter cap.
If the filter cap is composed of two pieces, press the
tab on the filter cap downwards and pull the piece out
towards yourself.
a. Place a large container in front of the filter to catch water
from the filter.
b. Loosen pump filter (anticlockwise) until water starts to
flow. Fill the flowing water into the container you have
placed in front of the filter. Always keep a piece of cloth
handy to absorb any spilled water.
If the filter cap is one piece, pull the cap from both sides at
the top to open.
c. When the water inside the machine is finished, take out
the filter completely by turning it.
4. Clean any residues inside the filter as well as fibers, if
any, around the pump impeller region.
5. Install the filter.
6. If the filter cap is composed of two pieces, close the filter
cap by pressing on the tab. If it is one piece, seat the tabs
in the lower part into their places first, and then press the
upper part to close.
You can remove the filter cover by slightly pushing
downwards with a thin plastic tipped tool, through the
C gap above the filter cover. Do not use metal tipped tools
to remove the cover.
3. Some of our products have emergency draining hose and
some does not have. Follow the steps below to discharge
the water.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
15 / 20 EN
6 Technical specifications
Models (EN)
WCY 71032 HPTL
Maximum dry laundry capacity (kg)
Height (cm)
7
84
Width (cm)
60
Depth (cm)
56.5
Net weight ( 4 kg.)
Electrical input (V/Hz)
Total current (A)
70
220-240 V~ / 50Hz
10
2000-2350
1000
Total power (W)
Spin speed (rpm max.)
Stand-by mode power (W)
Off-mode power (W)
1.00
0.25
9211
Main model code
• / -
Single Water inlet / Double Water inlet
• Available
Technical specifications may be changed without prior notice to improve the quality of the product.
Figures in this manual are schematic and may not match the product exactly.
Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance
with the relevant standards. Depending on operational and environmental conditions of the product, these values may vary.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
16 / 20 EN
7 Troubleshooting
Programme cannot be started or selected.
• Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> To cancel the
programme, turn the Programme Selection knob to select another programme. Previous programme will be cancelled. (See “Canceling
the programme”)
Water in the machine.
• Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is
not harmful to the machine.
Machine vibrates or makes noise.
• Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
• A hard substance might have entered into the pump filter. >>> Clean the pump filter.
• Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.
• Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.
• Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand to
balance it homogenously in the machine.
• Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything.
Machine stopped shortly after the programme started.
• Machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the normal level.
Programme time does not countdown. (On models with display)
• Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes in adequate amount of water. The
machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer indicator will resume
countdown after this.
• Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches the selected temperature.
• Timer may stop during spinning step. >>> Automatic unbalanced load detection system might be activated due to the unbalanced
distribution of the laundry in the drum.
• Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and
to its surrounding environment. Laundry should be rearranged and re-spun.
Foam is overflowing from the detergent drawer.
• Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the
detergent drawer.
• Put detergent into the machine suitable for the programmes and maximum loads indicated in the “Programme and consumption table”.
When you use additional chemicals (stain removers, bleachs and etc), reduce the amount of detergent.
Laundry remains wet at the end of the programme
• Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage.
>>> Use recommended amount of detergent.
• Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and
to its surrounding environment. Laundry should be rearranged and re-spun.
warning: If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the
Authorized Service Agent. Never try to repair a nonfunctional product yourself.
A
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
17 / 20 EN
PRODUCT FICHE
Complying Commission Delegated Regulation (EU) No 1061/201
Supplier name or trademark
Beko
Model name
WCY 71032 HPTL
Rated capacity (kg)
7
Energy efficiency class (1)
Annual Energy Consumption (kWh) (2)
A++
194
1.175
0.934
0.826
Energy consumption of the standard 60°C cotton programme at full load (kWh)
Energy consumption of the standard 60°C cotton programme at partial load (kWh)
Energy consumption of the standard 40°C cotton programme at partial load (kWh)
Power consumption in ‘off-mode’ (W)
Power consumption in ‘left-on mode’ (W)
Annual Water Consumption (l) (3)
Spin-drying efficiency class (4)
0.250
1.000
9020
C
Maximum spin speed (rpm)
1000
62
Remaining moisture Content (%)
Standard cotton programme(5)
Cotton Eco 60°C and 40°C
Programme time of the standard 60°C cotton programme at full load (min)
Programme time of the standard 60°C cotton programme at partial load (min)
160
145
Programme time of the standard 40°C cotton programme at partial load (min)
130
Duration of the left-on mode (min)
N/A
56/74
No
Airborne acoustical noise emissions washing/spinning (dB)
Built-in
(1) Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency)
(2) Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and
the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.
(3) Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load. Actual
water consumption will depend on how the appliance is used.
(4)Scale from A (Highest Efficiency) to G (Lowest Efficiency)
(5) “Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which
the information in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that
they are the most efficient programmes in terms of combined energy and water consumption.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
18 / 20 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
19 / 20 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
20 / 20 EN
|