Beko Dishwasher DSFN1530 User Manual

Dishwasher

DSFN 1530

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

1. Know your dishwasher /

speciﬁcation

Standards and testing information / EC

Declaration of conformity

6. Operating the dishwasher 20

7. How to clean your machine 21

Upper spray arm

Lower spray arm

2. Warning and safety

information

Electrical Safety

Children’s Safety

General

Recycling

Energy and water saving

What should not be washed in your

dishwasher

8. Before calling service /

Trouble shouting

3. Before ﬁrst use

Hot Air Drying

Electrical requirements

4. Installation

Warning

This appliance must be earthed

Important

Fitting a different plug

Water inlet hose connection

Drain Hose Connection

Installation of dishwasher

5. How to use

Water hardness & regeneration

settings

Filling the (water softener)

dishwasher salt

Visual indicator

Detergent use

Filling detergent dispenser

Rinse aid

Loading dishwasher

Folding plate support rods

Upper basket height adjustment

(unloaded)

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Know your dishwasher / speciﬁcation

��

�

��

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Speciﬁcation

Load Capacity

Height

: 12 Place settings

: 850 mm

Width

: 598 mm

Depth

: 598 mm

Depth/Height (without worktop)

Net weight

: 570 mm / 820 mm

: 49 kg

Supply voltage

Fuse currrent

Total power

: 220-240 V ~ 50 Hz

: 13 A

: 1900-2200 W

: 2000 W

Heater power

Pump powers

Diameter of plates for :

Upper basket

Lower basket

: 125/30 W

: 25 cm max.

: 31 cm max.

Because we continually strive to improve our products, we may change our

speciﬁcations and designs without prior notice.

Standards and testing information / EC Declaration of

conformity

This appliance has been designed,

2006/95/EC

constructed and distributed in compliance

2004/108/EC

with the safety requirements of EC

IEC 60335-2-5

directives.

Load capacity : 12 place settings.

EN 50242

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Warning and safety information

Never allow your children to play on or

sit onto the front door when the front

door is open.

Electrical Safety

The dishwasher should only be

operated on the voltage speciﬁed. For

electrical safety, only earthed plugs

and sockets should be used. Always

use the fused plug provided with the

appliance. The user is responsible

for meeting these basic safety

requirements. The life of your machine

and your safety depend on you using

an electrical installation compliant to

standards.

After unpacking your machine, keep

the packing material out of children’s

reach.

Warning !

Long cutlery, such as ladles and

long knives, etc must be placed

horizontally on top of the full cutlery

basket or on the racks to prevent

accidental injury.

Do not use an extension cable.

When disconnecting your machine

from the mains supply, always pull from

the plug. Never pull the cord itself.

General

This dishwasher has been designed to

clean your dirty dishes at home.

Never use chemical solvents in your

machine; this may lead to explosion

risk.

Children’s Safety

Never allow your children to play with

your dishwasher.

Never use materials other than

specially produced softening salts in

the salt dispenser of your machine.

Dishwasher detergents contain irritants

and abrasives. These ingredients might

have caustic effects in the eyes, mouth

and throat.

Never use materials other than

specially produced detergents and

rinse-aids in the detergent and rinse

aid dispensers of your machine.

They can be extremely dangerous if

swallowed. Avoid contact with skin

and eyes. Check that the detergent

receptacle is empty after completion of

the wash cycle.

Please dispose of the packaging

material and old appliances carefully.

Please ensure old machines do not

become a threat to child safety. It is

known that children lock themselves

in unused machines. To avoid such a

problem it is advised that you cut the

mains cable off and break the door

latch so it does not lock.

Keep detergents out of children’s

reach and do not put detergent in the

machine until right before you start the

washing programme.

The water in your dishwasher is not

suitable for drinking, for this reason

do not allow your children near your

machine when the front door is open.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

The door of your machine is designed

to support the weight of a full basket

when the lower basket is pulled all the

way out. Never place any other load

on the door, otherwise the machine

may tip over.

human health due to the presence of

hazardous substances.

Energy and water saving

Scrape excess food from the dishes

before loading. Start your dishwasher

after fully loading the machine. Do not

use the pre-wash programme unless

required. Make your programme

After using the dishwasher always

close the door as an open door can be

a hazard.

selection as per the programme chart

and quick reference guide supplied.

Do not open the door whilst the

appliance is in operation.

What should not be washed in

your dishwasher

Recycling

Do not wash items soiled with

cigarette ash, candle, paint wax,

dyes, chemicals etc. since these may

damage your machine

Please help us to protect our

environment. Packing materials and

some parts of your machine are

produced using recyclable materials.

These materials are marked up with

recycling symbol and material type

information (>PE<, >PS<, >POM< …).

These raw materials should not be

mixed with daily garbage and should

be given to recycling centers.

We suggest you contact your local

authority for disposal information and

facilities available.

Do not wash forks, knives and spoons

with wooden or bone handles, items

stuck together with adhesives,

plastic items not resistant to high

temperatures. Copper, tin items and

aluminium ware in your dishwasher.

As with hand washing, some “on-

glaze” decorated china, aluminum or

silver have a tendency to discolour or

fade. Also, certain types of glassware

and crystals may loose their shine and

become opaque in time.

This product bears the

selective sorting symbol

for waste electrical and

electronic equipment

(WEEE).

A chemical reaction can occur between

silver cutlery and stainless steel

cutlery. As a precaution, do not wash

together.

This means that this product must

be handled pursuant to European

Directive 2002/96/EC in order to be

recycled or dismantled to minimize its

impact on the environment. For further

information, please contact your local

or regional authorities.

Iron and cast iron objects can rust and

stain other items.

Pay special attention to whether or not

the item you wash in the dishwasher is

dishwasher-proof.

Electronic products not included in the

selective sorting process are potentially

dangerous for the environment and

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

If in doubt, contact the manufacturer of

the item.

Hot Air Drying

Hot Air Drying ensures your dishes are

dried efﬁciently.

Do not overload your dishwasher or

do not load items other than those

mentioned in this manual.

Before ﬁrst use

After unpacking your dishwasher,

check the machine against any

Installation

possible transportation damage. Never

install and use damaged machines. If

your machine is damaged contact your

retailer. Always have your machine

installed by qualiﬁed electrician/

When deciding on where to install

your new dishwasher, ensure that the

position of your dishwasher makes it

easy and quick for you to place the

dishes in the dishwasher and also to

take them out and store away after the

dishwashing is completed.

plumber to ensure correct installation.

Any repairs and maintenance work

on this dishwasher should be carried

out by authorised service staff only.

Unauthorised repairs are not only

dangerous, but also lead to the

cancellation of your warranty.

Avoid placing the dishwasher where

the ambient temperature is likely to fall

below. 0 degrees C. (32° F)

When positioning your appliance, take

care not to damage your ﬂooring, pipes

wall coverings etc. Do not move the

appliance by pulling by the door or

handle

Make sure the electricity and water

connections of your dishwasher are

in compliance with the instructions for

assembly as stated in the relevant part

of this booklet.

Electrical requirements

Any water remaining in the dishwasher

after production should be carefully

removed due to reasons of hygiene.

Therefore, always select a pre-wash

programme before ﬁrst use

Before you insert the plug into the wall

socket make sure that the voltage and

the frequency shown in the rating label

corresponds to your electricity supply.

(Pre-wash or Economy programme).

We recommend that this appliance be

connected to the mains supply via a

suitable switched and fused socket in a

readily accessible position.

Before the ﬁrst wash, add 1 lt of

water to the salt container of your

machine.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

If the supply cord or the mains lead

is damaged please do not replace

it by your own. The supply cord or

the mains lead must be replaced by

a Beko Authorized Service Agent

personnel or a similarly qualiﬁed

person.

1. Connect the green - yellow or

green (earth) wire to the terminal

in the plug marked ‘E’ or with the

symbol

or coloured green

and yellow or green.

2. Connect the blue (neutral) wire to

the terminal in the plug marked ‘N’

or coloured black.

3. Connect the brown (live) wire to

the terminal in the plug marked ‘L’

or coloured red.

Warning

This appliance must be

earthed

With the alternative plugs a 13A fuse

must be ﬁtted either in the plug or

adaptor or in the main fuse box. If in

doubt contact a qualiﬁed electrician.

If the ﬁtted moulded plug is not suitable

for your socket, then the plug should

be cut off and an appropriate plug

ﬁtted.

Destroy the old plug, which is cut off as

a plug with a bared cord could cause a

shock hazard if inserted into a socket

elsewhere in the house.

��

The moulded plug on this appliance

incorporates a 13A fuse. Should the

fuse need to be replaced an ASTA

approved BS1362 fuse of the same

rating must be used. Do not forget

to reﬁt the fuse cover. In the event of

losing the fuse cover, the plug must

not be used until a replacement fuse

cover has been ﬁtted. Colour of the

replacement fuse cover must be the

same colour as that visible on the

pin face of the plug. Fuse covers are

available from any good electrical

store.

�

��

Important

Fitting a different plug

As the colours of the wires in the

mains lead of this appliance may not

correspond with the coloured markings

identifying the terminals on your plug,

proceed as follows:

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Water inlet hose connection

Make sure your plumbing is suitable to

install your new dishwasher. If in doubt

contact a qualiﬁed plumber.

Drain Hose Connection

Fit the drainage hose of your machine

to the drainage pipe without bending.

Secure your hose ﬁrmly to the waste

pipe to avoid it coming off during the

washing process.

The appliance must be connected

to the water mains using the new

hose set supplied with your new

dishwasher. Old hose sets must not

be re-used.

The waste pipe must only be

connected into the foul drains and not

surface water drainage system.

The water pressure coming from

the water mains supply must be a

minimum of 0.3 and a maximum of 10

bars.

The hose should be placed between

50 cm and 110 cm from the ﬂoor level

and must not be extended otherwise

the machine may not empty the waste

water.

Connect the straight end to your water

mains supply

Ensure plastic ﬁlter

and black rubber seal is in place.

Please turn on the tap and check for

leakages after connecting the hose.

We recommend the tap is turned off

when the machine is not being used.

If you only have one cold water

feed (For example for your washing

machine) don’t worry. a Y adaptor

will provide you with the additional

cold water feed you need for your

dishwasher. Y adaptor is available from

most DIY stores.

��

�

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

will not ﬁt under the worktop a special

part replacing the top trim must be

provided and installed by an Authorized

Service Agent. It should never be

operated without a top cover.

Installation of dishwasher

Remove all packaging before

positioning the machine.

See the following diagram. Ensure

there is a clearance each side of the

machine to allow slight side ways

movement for servicing.

Please contact the Authorised Service

Agent for details.

Position the machine next to a water

tap and a drain.

Note:

If there is already enough space, you

don’t need to remove the worktop to

install it under the counter.

When inserting the machine, ensure

that the water inlet and drain hoses are

not linked or squashed.

In the unlikely event that the product

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Care must be taken to

ensure that the appliance

does not stand on the

electrical supply cable.

Good levelling is

essential for correct

closure and sealing of the

door.

Make sure your

dishwasher is perfectly

level using the adjustable

feet.

��

�

When the appliance is correctly levelled, the door will not catch on the inner liner

on either side of the cabinet.

If the door does not close correctly, loosen or tighten the adjustable feet, until the

machine is perfectly level.

5 How to use

Water hardness & regeneration settings

The dishwasher requires lime free water. Hard water leaves watermarks on your

dishes. Your dishwasher has a special water softening system to remove the

hardness of the tap water. Setting this system correctly will increase the washing

effectiveness.

To ﬁnd out the water hardness level of water in your area, contact your local

Water Board or Determine water hardness level by the help of test strip provided.

If you move to a different location, the level of water hardness will possibly

be changed. It is essential to reset the water hardness in order to obtain

optimum washing efﬁciency.

��

�

��

�

��

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

��

�

��

! For level 5 and level 6 there is no

difference between hardness level

settings.

Programme Follow-up indicators

light up continously when machine

enters into the water hardness

adjustment mode.

If the hardness of the water you

use is more than 80°dF (French

Hardness) or if you are using pit

water, we recommend that you use

ﬁlters and puriﬁers.

•

To adjust new Water Hardness

Level: adjust the water hardness

level according to the “Water

Hardness Level Adjustment Table”

( See Water Hardness Level

Adjusment Table ) by pressing the

programme selection button again.

If you select a water hardness

level other than stored in the

memory, programme follow up

indicators ﬂash with an interval

of 1 second. The selected water

hardness level in indicated by the

Programme Selection indicators.

Press “Start/Pause/Cancel” button

for once to store the level you have

selected. Programme follow-up

indicators light up continuously

when the water hardness level is

stored.

* If your tap water is below 9F

(French hardness), you do not need

to use special dishwasher salt in your

machine. In this case, salt indicator

light will be on continuously.

•

Open the door of the machine

Press programme selection button

when machine is switched off.

Keep programme selection button

pressed and press on/off button

to turn your machine on. Do not

release the programme selection

button until the deﬁned “Water

Hardness Level Indicator” of your

machine is displayed ( See Water

Hardness Level Adjusment Table )

•

Press the on/off button to turn off

your machine.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

! If you move your house, it is very

important to make the water

Using the funnel provided will make

ﬁlling easier.

hardness level adjustment of your

machine according to the new

location you move in order to

preserve the washing efﬁciency.

After you ﬁll the container, screw cap

tightly back into place turning clockwise

until you hear a click sound.

Visual indicator

Filling the (water softener)

dishwasher salt

The ﬂoat drops and is no longer visible

when the salt container needs to be

reﬁlled.

Only use special pelletized dishwasher

salt in your machine to soften the hard

water. Never use other types of salts

including table salt, animal feeding salt,

sea salt, culinary salt. These types of

salt do not dissolve in water easily and

will damage your appliance beyond

repair.

To ﬁll the container with softening

salt, remove the lower rack ﬁrst and

unscrew the cap of the water softener

turning anti clockwise .

Using the funnel provided will make

ﬁlling easier.

When you run the dishwasher, the

Water softener will be full of water.

Therefore, adding softening salt

should always be done immediately

before you start the dishwasher.

After you ﬁll the container, screw cap

tightly back into place turning clockwise

until you hear a click sound.

�

��

�

��

Caution : Only ﬁll with salt just before

starting one of the complete washing

programmes to prevent any grains of

salt causing corrosion.

You can put approximately 2 kg

softening salt in the Water softener.

To ﬁll the container with softening

salt, remove the lower rack ﬁrst and

unscrew the cap of the water softener

turning anti clockwise .

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Warning!

Detergent use

Two-in-one and three-in-one

detergents

You will obtain the best results from

your dishwasher if you use separate

detergent, rinse aid and water-

softening salt.

Any brand of powder, gel and tablet

detergents that have been designed for

household dishwasher, may be used.

Keep detergents in a cool and dry

place and out of the reach of children.

Detergent manufacturers also produce

combined detergents known as ‘two-in-

one’ and ‘three-in-one’.

Detergent must be added to the

container before each use.

Detergent overdose may cause

scratches on your dishes and there

may be traces of detergent left in your

machine.

Three-in-one: These products contain

detergent, rinse aid and water-

softening salt.

Two-in-one: These products contain

detergent and either rinse aid or water-

softening salt.

Three types of detergent are available

•

Phosphate and containing

chlorine.

In general, you will obtain satisfactory

results from combined detergents only

under speciﬁc usage conditions. These

detergents contain predetermined

amounts of rinse aid and/or softening

salt. This means that you cannot adjust

the amount of water-softening salt

and rinse aid required to suit the water

hardness level in your home.

•

Phosphate containing no chlorine

Neither containing phosphate nor

chlorine

New compact powders are generally

phosphate-free. As phosphates have

water softening properties, we suggest

you add salt to the salt container even

if the hardness of your water is as low

as a 6 clarke degrees.

You should bear the following points in

mind when using such detergents:

In hard water areas if a phosphate free

detergent is used, white marks on the

dishes and glasses may be observed.

It may be prevented by increasing the

amount of detergent.

•

Be sure to check the speciﬁcations

of the product you are using and

whether it is a combined product

or not.

•

Follow the instructions on the

packet when using these products.

The use of these products at the

correct appliance settings will

ensure economical use of salt and/

or rinse aid.

If the detergent is in tablet form,

never place these in the internal

section or cutlery basket of the

Detergents without chlorine have less

bleaching effect. Coloured stains may

not be completely

removed. This may be prevented by

increasing the amount of detergent,

using a programme with a higher wash

temperature or using a detergent with

chlorine.

•

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

dishwasher. Always place the

tablets in the detergent dispenser

of the detergent holder.

Using two-in-one detergent and

rinse aid

•

These detergents will not give you

the same drying performance that

you can obtain by using separate

detergent, salt and rinse aid. To

increase the drying performance:

Put your appliance’s rinse aid

setting at “1” and apply rinse aid.

When the rinse aid is used up,

add more rinse aid to the rinse aid

dispenser.

If you use combined detergents

with a rinse aid setting higher

than 1, hand contact may leave

rainbow-coloured water stains on

the washed items and inside the

machine.

Using three-in-one detergent,

softening salt and rinse aid.

•

These detergents will not give you

the same drying performance that

you can obtain by using separate

detergent, salt and rinse aid. To

increase the drying performance:

Put your appliance’s rinse aid

setting at “1” and apply rinse aid.

When the rinse aid is used up,

add more rinse aid to the rinse aid

dispenser.

If you use combined detergents

with a rinse aid setting higher

than 1, hand contact may leave

rainbow-coloured water stains on

the washed items and inside the

machine.

•

These detergents do not contain

softening salt so you need to use

the softening setting as described

in the manual, making sure that

there is salt in the water softener

with every wash and that you reﬁll

the water softener with salt every

time it is empty.

•

If you use combined detergents

without adding salt, lime scale may

form especially on glasses. To

avoid lime scale formation:

Put your appliance’s water

softener setting at “1” and add salt. Important warning

When the salt is used up, add

Should you encounter a problem that

more salt to the water softener.

has previously never occured after you

start using these detergents, contact

the detergent manufacturer directly.

You will ﬁnd contact details on the

packet.

Using two-in-one detergent:

detergent and softening salt

•

These detergents do not contain

rinse aid so you need to use the

rinse aid setting as described

in the manual, making sure that

there is rinse aid in the rinse

aid dispenser with every wash

and that you reﬁll the rinse aid

dispenser with rinse aid every time

it is empty.

If you stop using this kind of

detergent:

•

Ensure that the salt and rinse aid

dispensers are full.

•

Put the water hardness setting at

the highest level and run a wash

cycle with the appliance empty.

After washing while empty, return

the water hardness setting to the

correct level for your mains water

•

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

hardness shown in the manual.

Put the rinse aid setting at the

correct level.

Rinse aid

Use only rinse aid intended for

household dishwashers.

•

The rinse aid is specially formulated

to be used in the dishwashers for the

prevention of watermarks and scale on

dishes and to increase the efﬁciency

of the washing and drying processes.

Therefore, make sure that

there is adequate amount of rinse

aid in the rinse aid dispenser of your

machine.

Filling

detergent

dispenser

If the dishwasher

is considerably

full and the dishes

are relatively

dirty, ﬁll the main

container (A) up

to 25cm³ level. If the dishwasher is

not quite full and the dishes are only

slightly soiled, ﬁll the main container

(A) only up to 15cm³ level.

If your dishes are kept unwashed for

a long time and the food particles are

stuck on the dishes also ﬁll the small

container (B) up to 5cm³. Depending

on the degree of soiling and the

water hardness in your area it may be

necessary to add more detergent.

You can adjust the amount of rinse

aid used during the wash programme

by turning the rinse aid dispenser

regulator (C).

The dispenser regulator (C) may be set

between levels 1 and 6 (6 being the

maximum amount of rinse aid usage).

Your machine is pre-set at the factory

to level 4.

According to the ﬁnish and drying

results obtained, adjust the dose of

rinse aid by means of the six position

selector. (Position 1: minimum dose,

Position 6: maximum dose.) Gradually

increase the dose if there are drops of

water or lime spots on the dishes after

washing. Reduce it if there are sticky

whitish streaks on the dishes.

Powder and gel detergents are poured

into the dispenser.

If you are using tablet detergent read

the manufacturer’s recommendations

on the packaging in order to determine

where the tablets should be placed

inside the dishwasher (detergent

dispenser, cutlery basket, etc.)

After you put in the detergent, shut the

container lid (D) and ensure you hear

the clicking sound.

During the wash programme the

detergent will dispense automatically

and the lid (D) will remain open when

the programme ﬁnishes.

Do not use detergent when using the

pre-wash programme.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Filling the rinse aid dispenser

Open the rinse aid dispenser lid by

pressing the button as shown in the

diagram.

Long-stemmed glasses should lean

against the basket, the racks, or the

supports not against the dishes.

Fill up with rinse aid until the container

is full to level of ’max’ mark .

Put the lid (E) on and ensure you hear

the clicking sound.

The shelves on the rack are made

height adjustable to accommodate tall

items.

Remember to CLOSE the lid after

every reﬁll.

Make sure you clean any rinse aid that

you might have spilled.

When loading your dishwasher please

ensure tall glasses (and/or wine

glasses) rest against the sides of the

upper basket. Do not allow tall glasses

to rest against each other since they

may be damaged during washing if not

properly supported.

Always arrange saucepans, cups and

glasses etc. up side-down.

��

You can fold the racks in the upper

basket when you need more space for

larger items .

Loading dishwasher

Loading the dishwasher correctly will

increase the washing, drying and

energy performance of your machine.

Examine the information given in this

section and the information stated

in the Programme chart and quick

reference card given with the manual.

Remove any large scraps of food

from the dishes before placing in the

dishwasher to avoid clogging the ﬁlters.

��

There are three separate baskets, in

which you can put your dishes.

�

Place large or heavily soiled items in

the lower basket, and small, light or

delicate articles in the upper basket.

Put forks, small and medium size

knives and spoons in the cutlery

basket.

�

Place tall, narrow items in the middle of

the racks.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Warning !

Folding plate support rods

There are four separate “folding plate

support rods” in the lower basket of

your dishwasher designed to allow

you more space to accommodate

saucepans and large bowls in the

lower basket. You can either fold each

section (1,2,3,4) individually or, all at

once, to create a large empty space.

Simply press the handgrips (A) and

fold them down”

Long cutlery, such as ladles and

long knives, etc must be placed

horizontally on top of the full cutlery

basket or on the racks to prevent

accidental injury.

Handle of the cutlery basket is not

removable

Upper basket height

adjustment (unloaded)

The factory ﬁtted position of the upper

basket is the higher position. That is

lower wheels are engaged.

According to the size of the dishes you

can change the position of the upper

basket.

�

To do this.

Release the latches on both the

right and left tracks by turning them

sideways.

Pull out the basket

completely.Insert the other set of

wheels and place the basket back on

the track then shut the latches.

�

Place larger items

such as saucepans

in the lower basket.

You can remove

the cutlery basket

to make room for

other items .Place

spoons and forks in

the cutlery basket

with handles down

and knives with handles up to prevent

accidental injury.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Standard loading and testing institute information

�

Loading capacity:

Lower and upper baskets: Standard

12 place settings

�

Detergent:

5+25 gr. as compliant

to EN 50242-DIN 44990.I EC436

international norms

Testing programme:

Economy 50 ºC

�

As compliant to EN 50242

international norms

�

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Operating the dishwasher

be washed, open the door carefully.

•

Turn the water tap on. Open the

door of the machine.

Check that the upper and lower

arms can rotate freely.

Pour (Put in) the detergent.

Close the door of the machine

Push in the on/off button and

check that the programme

indicator lights come on.

Check the salt and rinse aid level

indicator lights before you start the

machine. If necessary add salt and

rinse aid.

Select the required programme by

referring to the programme chart.

Choose the desired programme by

turning the selector knob

Press start / stop button and check

that the start / stop indicator light

comes on.

Care must be taken if opening the

door, as steam and water will escape.

Then after putting in the item, close

the door. The dishwasher will resume

operation.

•

Unloading dishwasher

Dishes should be allowed to cool for

about 15 - 30 minutes after the end of

the programme.

•

You will improve drying results by

leaving the dishwasher door ajar for

at least 15-30 minutes as soon as the

programme ﬁnishes.

! Care must be taken when opening

the door, as steam will escape.

First unload the lower, then the upper

rack. This prevents drops of water from

falling onto the full lower basket when

the dishes in the upper basket are

being removed.

! Do not open the dishwasher door

whilst the appliance is in operation.

However, in case the door is opened

while the machine is working, then

a safety mechanism ensures the

machine immediately stops. Water may

be very hot, so be careful.

! Care must be taken if opening the

door, as steam and water will escape.

•

Press the on/off button after the

programme is completed. The

indicator lights will go off.

Unload the baskets - we

recommend to turn off the water

tap when not in use

•

! Just after the dishwasher has started

the selected programme, if you ﬁnd

that you want to put in another item to

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

7 How to clean your machine

Cleaning your machine at regular

intervals ensures longer product life

and reduces the risk of recurring

problems. Clean spray arms and in

particular ﬁlters at least once a week

! Always unplug the appliance and turn

off the water supply before cleaning.

��

To clean the door seal, use a neutral

detergent and a damp cloth. To clean

the control panel, use only slightly

damp cloth.

��

! Do not use abrasive detergents.

If the appliance is not going to be used

for a long period of time, switch off,

turn off the water clean and leave the

door ajar.

How to clean the ﬁlters and spray

arms ﬁlters

For the efﬁcient operation of your

dishwasher, check the ﬁlters and the

spray arms regularly.

There are three different ﬁlters in your

machine

Main ﬁlter

Coarse ﬁlter

Micro ﬁlter

To remove the coarse and micro

ﬁlter assembly to clean, turn it anti

clockwise as far as it goes and lift it up.

Then press the two tongues in wards

and pull out the coarse ﬁlter.

Pull the main ﬁlter off.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Clean all three ﬁlters under running tap

water with a brush.

Reinsert the main ﬁlter in its place.

Place the coarse ﬁlter into the micro

ﬁlter. Ensure the marks align properly.

Turn the coarse ﬁlter clockwise until

you hear a clicking sound.

It is important that you ﬁt the ﬁlters

correctly.

Caution : the dishwasher must not

be used without ﬁlters.

Incorrect repositioning of the ﬁlters

will produce poor washing results.

Cleaning of the ﬁlters is vital to

ensure correct operation of the

machine.

Upper spray arm

Turn the nut anti clockwise and remove

both the nut and the spray arm.

Flush away food particles under

running water.

Put the spray arm back on and screw

on the nut turning clockwise until a

clicking sound is heard.

Lower spray arm

Remove the spray arm from its slot

by releasing the catches and pulling it

upwards.

Flush away the food particles under

running water.

Reinsert the spray arm back into its

original position.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

8 Before calling service / Trouble shouting

Before calling service check the following & Trouble shooting guide supplied on

the following page.

�

��

�

��

TROUBLE SHOOTING GUIDE

SYMPTOMS

POSSIBLE CAUSES

SOLUTIONS

Insufﬁcient amount of

detergent

Increase the amount of detergent, especially when

washing full loads, or in hard water.

Increase water softener dosage. Use additional

detergent, increase rinse agent dosage.

Hard water.

Check the nozzle holes in the spray arms. They may

be blocked with a soil particle. Check and clean them

periodically.

Spray arms need cleaning

Spotting /

ﬁlming / poor

cleaning results

Follow instructions for use for proper loading

procedures. Place dishes so water spray reaches all

soiled surfaces. Do not overcrowd the baskets since

this will block the water spray.

Improper loading.

Insufﬁcient water ﬁll.

Check mains water pressure

Remove any accumulated or deposited foods. Check

and clean them periodically.

Filter system needs cleaning.

Oversudsing - Prewashing withRinse items thoroughly before putting them in the

a liquid dishwashing detergent.dishwasher to remove dishwashing detergent.

Check to be sure water action is not blocked by

Water not reaching surfaces, dishes. Check ﬁlter system for accumulated or

dishwasher overcrowded.

deposited food or detergent. Load dishwasher

correctly. Keep ﬁlter system clean.

Small particles

(food or

Insufﬁcient water ﬁll.

Check mains water pressure

detergent) left

on items

Use powder detergent within one to two months after

purchase. Open one box at a time. Always close

pouring spout after each use. Store in a cool, dry

place.

Powder detergent stored

too long or under adverse

conditions.

Rinse aid supply depleted.

Add rinse aid to the dispenser.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remove spots with silver polish. Rewash. Wash soon

after use, or pre-wash items if they will not be washed

right away. Do not overload cutlery basket. Avoid

spilling or pouring detergent directly on ﬂatware. Make

sure dispenser cup is properly closed.

Prolonged contact with salty

or highly acidic foods or

with undissolved or highly

concentrated detergent.

Pitting of

stainless steel

items

Load so that all items are properly tilted for good

drainage. Avoid nesting of dishes and/or silverware.

Improper loading.

Dishes not dry

Rinse aid supply depleted.

Add liquid rinse aid .

The condition may not always be preventable. To

minimize the possibility of etching, use minimum

amount of detergent.

A water or chemical reaction

with some glassware. Usually

caused by some combination

of soft or softened water and

alkaline washing solutions

reacting with the glassware.

Can be accelerated by poor

rinsing, overloading and

Scratches on

glassware

Use of the appropriate programme.

Use of a rinse aid may also help.

excessive temperature.

If using powder detergent,

there may be dampness in the

dispenser.

Make sure dispenser is dry before adding powder

detergent. Start dishwasher immediately.

If using gel detergent, the

detergent may be left in

dispenser too long before

using.

Start dishwasher soon after adding gel detergent. Do

not allow detergent to dry out in dispenser.

Detergent

cakes in

detergent

dispenser.

Do not overﬁll. Cover should close tightly. Check

cover for ﬁt.

Faulty cover.

Improper loading.

Do not place large items in front of dispenser.

Use detergent within one to two months of purchase.

To assure freshness, buy detergent as needed and

no more than one or two at a time. Store in a cool, dry

place.

Old detergent.

Chipping and

breakage of

dishes/glasses

Load with care following the instructions for use.

Place glassware so it does not touch the other dishes.

Remove from dishwasher carefully.

Improper loading.

Use the pre-wash cycle at least once a day until a

load accumulates, or hand rinse dishes before loading

dishwasher.

Dishes washed only every two

or three days.

Odour in

dishwasher

A dirty ﬁlter system may

Clean ﬁlter system.

contribute to a bad odour.

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Loss of frozen food in freezers

or fridge/freezers. (Food loss

insurance is often included within

your household contents insurance

policy, or may be available

Guarantee for Refrigeration,

Cooking Appliances, Washing

Machines & Dishwashers.

separately from your retailer).

Important notes.

Your new Beko product is guaranteed

against the cost of breakdown repairs

for twelve months from the date of the

original purchase.

•

Your Beko product is designed and

built for domestic household use

only.

•

The guarantee will be void if the

product is installed or used in

commercial or non-residential

domestic household premises.

The product must be correctly

installed, located and operated in

accordance with the instructions

contained in the User Instructions

Booklet provided.

What is covered?

•

Repairs necessary as a result

of faulty materials, defective

components or manufacturing

defect.

•

The cost of functional replacement

parts, but excluding consumable

items.

The labour costs of a Beko

approved repairer to carry out the

repair.

Professional installation

by a qualiﬁed Electrical

Domestic Appliance Installer is

recommended for all Washing

Machines, Dishwashers and

Electric Cookers

What is not covered?

•

Transit, delivery or accidental

damage or misuse and abuse.

Cabinet or appearance parts,

including knobs, ﬂaps, handles or

container lids.

•

Gas Cookers must only be

installed by a CORGI (or BORD

GAIS) registered Gas Installer.

The guarantee is given only within

the boundaries of the United

Kingdom and the Republic of

Ireland.

•

Accessories or consumable items

including but not limited to, ice

trays, scrapers, cutlery baskets,

ﬁlters and light bulbs.

Repairs required as a result of

unauthorised repair or inexpert

installation that fails to meet the

requirements contained in the user

instruction book.

•

The guarantee is applicable

only to new products and is not

transferable if the product is

resold.

•

Beko disclaims any liability for

incidental or consequential

damages.

The guarantee does not in anyway

diminish your statutory or legal

rights.

•

Repairs to products used on

commercial or non-residential

household premises.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before requesting service please

check the trouble-shooting guide

in the Operating Instructions as a

charge may be levied where no fault

is found even though your product

may still be under guarantee.

•

The product guarantee does not

cover damages to plates,glass

ware, cutlery, crockery and also

damage to the product itself as

a result of using these “Three-in-

one”, “Two-in-one” detergents.

Service once the manufacturers

guarantee has expired.

Please keep your purchase receipt

or other proof of purchase in a

safe place; you will need to have it

should the product require attention

under guarantee.

If you have purchased an extended

guarantee please refer to the

instructions contained within the

extended guarantee agreement

document. Otherwise please call the

appropriate number above where

service can be obtained at a charge.

You should also complete the details

below; it will help us assist you when

requesting service. (The model

number is printed on the Instruction

Booklet and the serial number is

printed on the Rating Label afﬁxed to

the appliance)

Should you experience any difﬁculty

in obtaining service please contact the

Beko Customer Help-Line.

Tel: 0845 6004911

Model No:

e-mail: [email protected]

Serial No:

Retailer:

Date of purchase:

Beko plc, Beko House, Caxton Way,

Watford, Herts, WD18 8UF

www.beko.co.uk

For service under guarantee simply

telephone the appropriate number

below

UK Mainland & Northern Ireland

Fridges & Freezers

Electric Cookers

0845 6004903

0845 6004902

Gas&Dual Fuel Cookers 0845 6004905

Washing Machines

& Dishwashers

0845 6004906

Republic of Ireland

All Refrigeration, All Cookers

01 862 3411

Washing Machines & Dishwashers

17 1753 0100-00

Download from Www.Somanuals.com. All Manuals Search And Download.

3D Connexion Sewing Machine 7318 User Manual
Ace Hardware Computer Monitor 3009701 User Manual
AGFA Printer TM 14ADV User Manual
Agilent Technologies Computer Drive E5070BU User Manual
Agilent Technologies Stereo System 3589A GP IB User Manual
Aiwa Stereo System NSX D70 User Manual
Asus Network Card P4S333 VM User Manual
Axis Communications Security Camera AXIS M1144 L User Manual
Behringer Stereo Equalizer DEQ2496 User Manual
Beko Refrigerator CDA 565 FS User Manual