Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Model #7311
Sit N Stand LX
Tandem Stroller
with Car Seat Snap N Go Attachment System
Instruction Manual
Convenience through innovation and thoughtful design
01.06
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
Parent Tray
Front Wheels
Child Tray
Canopy
Snap N Go Attachment
See Page 8
Rear Wheels
Foot Rest
Stroller
ASSEMBLING
TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE
INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
ASSEMBLY
1. Remove stroller from box. The front wheels, rear wheels, child tray, and
canopy need to be installed prior to use.
Fig. 1.
2. To attach the front wheels, unfold stroller as described in the section
following. See figure 1. Lean the stroller backwards so that it rests on
the handle and rear frame tubes and the front wheel tubes are pointing
upward. Position the front wheel assembly at the front tube such that
the large hole in the swivel assembly will slide onto the front tube. Push
each front wheel assembly onto the front tube being careful that wheel
assembly locks onto the front leg. Pull on the wheel assembly to ensure
that it is securely attached to the stroller. Please see figure 2.
Fig. 2.
Fig. 3.
Fig. 4.
3. Lean the stroller forward to rest on the front wheels. To attach the rear
wheels, position the rear axle and wheel assembly such that the brake
levers are facing to the rear of the stroller. Press the rear wheel assembly
onto the rear frame tubes being careful that the push buttons on the
forward side of each rear tube engage the hole on the forward side of
each rear wheel housing. Pull on the rear wheel assembly to ensure that
it is securely attached to the stroller. Please see figure 3.
4. Ensure that the wheels are firmly locked into place. Do Not use the
stroller if the wheels are not locked into place, but rather contact our
customer service department immediately at (800) 328-7363, between
the hours of 8:00am and 4:30pm PCT, for assistance.
5. Snap footrest onto front legs of stroller just below the seat. Push
downward on the footrest until it locks onto the rivets protruding from
both sides of each leg and snaps onto the U-shaped frame cross member.
Please see figure 4.
Snap On
Push
Down
3
Download from Www.Somanuals.com. All Manuals Search And Download.
6. To attach the front child tray, push the tray onto the front frame tube, lining
up the tray between the protruding rivet and the seat. Push backward on
the latch until snapped into place. The protruding rivet on the outside
of the frame tube should be above the tray latch. Check that the tray is
securely latched in place. Please see figure 5 and 6.
Fig. 5.
7. To remove front child tray, pull outward on the latches and pull outward
on the tray. Please see figure 7. Please note that you may attach or
remove one end at a time.
Rivet
WARNING: The childʼs tray is not a
restraint device: always secure your child with
the seat belt. DO NOT lift the stroller by the
childʼs tray. Use care when attaching the childʼs
tray on the stroller with a child in the stroller.
Fig. 6.
8. To attach the front canopy, line up the male fittings on the canopy with
the female fittings on the armrest and push both fittings downward until
snapped into place. Please see figure 8. Push forward on the front edge
of the canopy to open.
Fig. 7.
Fig. 8.
Your stroller is now ready to use
WARNING: Avoid serious injury from
falling or sliding out. Always use the seat belt.
TO SECURE CHILD
TO SECURE FRONT CHILD
1 The shoulder straps of the 5-point harness has 2 attachment positions.
Select the loop position that places the shoulder strap level with, or below
the top of the childʼs shoulder and feed the shoulder harness under the
correct loop. Please see figure 8a.
2. Carefully place the child in the stroller seat and bring the safety harness
around the childʼs waist and over the shoulders. Place the crotch strap
and between the childʼs legs. Insert the male end of each shoulder / waist
belt into the buckle on the crotch strap. Tighten the harness to be snug
around the childʼs waist and over the childʼs shoulders. Please see figure
9.
3. To release, apply pressure to both sides of each male clip until the clip
is released. This process requires a moderate amount of effort so as to
prevent an accidental release by your child. NOTE: Buckles may be hard
to release when 1st used.
Fig. 8a.
Fig. 9.
Shoulder Strap
Waist
Strap
Squeeze
Adjust for a
snug fit
Crotch Strap
TO SECURE REAR STANDING CHILD
1. The rear platform and jump seat are designed to accommodate a child
who is at least 2 1/2 years old, has good balance and coordination, and
is not over 40 inches tall. Push the jump seat bench to its most forward
position. Position the child on the platform on the back of the stroller.
Be sure child is facing forward and hands are holding frame. Secure the
safety belt behind child and engage buckle. See figure 10.
Fig. 10.
2. Be sure that the childʼs feet are fully on the platform at all times.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TO USE JUMP SEAT
1. Have child sit on the jump seat facing backwards. Secure the seat belt,
which is attached to the back of the seat, around the childʼs waist, and
buckle to the crotch strap. See figure 11.
Fig. 11.
2. Adjust the seat belt to be snug around the childʼs waist.
3. To release, apply pressure to both sides of the male clip until the clip
is released. This process requires a moderate amount of effort so as to
prevent an accidental release by your child.
4. Be sure that the childʼs feet are fully on the platform at all times.
TO ADAPT THE STROLLER TO CARRY
INFANT CAR SEATS
1. Please see Car Seat Chart following to determine the proper configuration
of the Snap N Go for your Infant Car Seat. See the page following that
corresponds with your brand of infant car seat for use with your car
seat.
SEATBACK POSITIONING
1. The front seat has a two position recline. To recline the seat, rotate the
recline bar and press backward on the seat back. Please see figure 12. To
place the seat in the upright position, press upward on the seat back while
rotating the recline bar.
2. The upright position should be used only for a child that is at least 6
months old. Note: Seat does not fully recline.
Fig. 12.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BRAKES
WARNING: Always set brakes when
the stroller is not being pushed so that the
stroller will not roll away. Never leave stroller
unattended on a hill or incline as the stroller
Fig. 13.
Fig. 14.
may slide down the hill.
1. To engage brakes, apply light downward pressure to the brake lever
located on each rear wheel. The stroller may require slight forward or
rearward movement in order to line up the teeth on the brake with each
wheel brake cluster. See figure 13. Check that the stroller will not move
and that the brakes are properly applied. To release, gently lift up on the
brake lever. See figure 14.
CANOPY
Fig. 15.
Fig. 16.
1. To open the canopy, push forward on the front frame of the canopies.
To close canopy, pull the front edge toward the rear of the stroller until
folded. Always fold the canopy prior to folding the stroller frame. Please
see figure 15.
2. The canopy will ratchet forward or back to block the sun. Pull forward on
the front canopy frame tube to move forward. Pull backward on the rear
frame tube to move back.
3. To remove the canopy, press the lock button on the end of the male fitting
while pulling upward on the canopy. Please see figure 16.
TO REMOVE FRONT CHILD TRAY
Fold Button
1. To remove front child tray, pull forward on the locking lever on the tray
arms to unlock. Please see figure 6. Please note that you may attach or
remove one end at a time. Also, the tray may be released on either side
and will swing away for easy access to your child. Please see figure 7.
TO FOLD STROLLER
Release Button
Fig. 17.
Do Not allow children near stroller while folding.
1. Close the canopy as described in the Canopy section above. The canopy
may be folded forward to fold the stroller or, if you need to reduce the size
of the folded stroller, may be folded back toward the rear of the stroller.
2. Unbuckle rear standing safety belt. Please see figure 10.
3. To fold the stroller slide the red fold latch safety button in the center of the
handle and squeeze the red handle while pushing forward on the handle.
Once the stroller begins to fold, release the red handle and pull upward on
the child tray until the stroller is folded. Please see figure 17.
4. Secure the stroller in the folded position by latching the fold latch, located
on the right side of the stroller handle, over the extended rivet on the
armrest. You may have to rotate the front wheels to fold the stroller
completely. Please see figure 18.
Fig. 18.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TO UNFOLD STROLLER
TO UNFOLD STROLLER
Do Not allow children near stroller while unfolding.
1. Release the folding latch, which is located on the right side. See figure
18.
2. Lift up on the stroller handle with both hands until the stroller frame is
erect and locked in the open position. The stroller has spring-loaded
latches on both sides of the frame. Test that both latches are fully
engaged prior to placing your child in the stroller.
STOP
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE
CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT (800) 328-7363 BETWEEN
THE HOURS OF 8:00AM AND 4:30PM PACIFIC COAST TIME FOR ASSISTANCE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Model #7311
Sit N Stand LX
Tandem Stroller
with Car Seat Snap N Go Attachment System
Instruction Manual
01.06
8
Convenience through innovation and thoughtful design
Download from Www.Somanuals.com. All Manuals Search And Download.
Car Seat Chart
Snap N Go Attachment
The Snap N Go attachment system is easily configured to carry most infant car seats in the market. New infant
car seats are introduced by various manufacturers from time to time and may not be listed below. If you have
an infant car seat not listed below, please call our customer service department at (800) 328-7363 between the
hours of 8:30 and 4:00 Monday through Friday for additional information and instructions.
The Snap N Go attachment system adapts to individual infant car seats by virtue of two adjustments: snap
bar rotation angle and snap bar position. Please see figure 1. The chart below indicates the required settings
for each of the infant car seats. Please keep in mind that many infant car seat manufacturers add names to the
different versions of their infant car seats to designate a fabric choice, a license, or a travel system name. For
instance, the Baby Trend Latch-Loc infant car seat is sold as part of the Symmetry Travel System. The infant
car seat is still referred to as the Latch-Loc for purposes of these instructions. Please refer to your infant car
seat instruction manual, or the manufacturer directly, to determine which infant car seat you own.
SNAP BAR
POSITION
SNAP BAR
ANGLE
INFANT CAR SEAT
Cosco Designer 22,
Designer 35
5
1
5
Cosco Ariva
Peg Perego
Evenflo Cozy Carry/
Portabout
5
Evenflo On My Way
Evenflo Embrace
Century Vante
Graco Snug Ride
Baby Trend
1
4
1
1
USE BT BAR
Snap Bar Position
BT Bar
Snap Bar
(Remove if
not using a
Baby Trend
Car Seat)
Figure 1.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1:
Remove the child tray. Insert the Snap N Go bar into the two plastic
fittings located on the lower frame tube of the stroller. Please see
figure 1. The bar will lock into place with the metal snap button
popping into the hole in the plastic fitting. Check that the snap
button is fully engaging the hole in the plastic fitting and that the
Snap N Go bar is securely attached to both sides of the stroller
frame. Please see figure 2.
Figure 1.
WARNING:Avoid serious injury from
falling, Do Not use the Snap N Go bar if it is not
securely locked onto both sides of the stroller.
Snap button
engages here
Step 2:
Refer to the table above to determine the correct Snap Bar position.
If the Snap Bar needs to be moved to a different location, remove
the screws holding the Snap Bar onto the Snap N Go Frame. Move
the Snap Bar to the proper position as shown in figure 3a and re-
attach with the screws and nuts provided. Tighten screws. Please
see figure 3b.
Figure 2.
Position "I"
Position "II"
Step 3:
Refer to the table above to determine the correct Snap Bar angle.
To adjust the Snap Bar angle, push the buttons on the outsides of
the plastic fittings as shown in figure 4a. Rotate the bar to match
the position specified and release the buttons. Please see figure 4b.
Check that the bar has locked into the required position on both
sides.
Position "III"
Position "IV"
Position "V"
Figure 3a.
You are now ready to connect your infant car seat to the Snap N Go
attachment system. Please see sections following for your specific
infant car seat.
Position "2"
Position "3"
Position "1"
Position "4"
Position "5"
Figure 3b.
Figure 4a.
Figure 4b.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Cosco Designer 22 and Designer 35
®
Please follow the following instructions for proper installation of
your infant car seat.
®
Installation of the Cosco Designer 22 and Designer
®
®
35 Infant Car Seat
Position “5”
1. Place front seat in the reclined position. With one hand grasp
the car seat handle (in its upright, carrying position) and gently
place the seat, so that the baby faces the rear of the stroller, onto
the Snap-N-Go attachment system so that the large groove on
the seat bottom rests on the Snap Bar.
2. Thread the two ends of the Car Seat Strap (attached to the Snap-
N-Go frame) through the seat belt slots on the sides of the car
seat, then snap the two buckles together (see Figure 2). The first
time you do this, you will need to adjust the length of the strap
for a tight fit around the car seat. FOR SAFE OPERATION,
IT IS VERY IMPORTANT THAT THE CAR SEAT STRAP
IS ALWAYS TIGHTLY FASTENED AROUND THE CAR
SEAT.
Snap Bar
Position “I”
Figure 1.
3. Test for secure installation by moving the car seat in all directions.
The car seat should be securely attached to the stroller.
®
®
®
Removal of the Cosco Designer 22 and Designer 35
Infant Car Seat
1. Unlock the Car Seat Strap and remove both ends from the seat
belt slots on the side of the car seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and lift the car seat upward from the Snap-N-Go
attachment system.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Peg Perego Primo Viaggio
®
Please follow the following instructions for proper installation of
your infant car seat.
Position “5”
®
®
Installation of Peg Perego Primo Viaggio Infant Car
Seat
1. Place front seat in the reclined position. With one hand grasp
the car seat handle (in its upright, carrying position) and gently
place the seat, so that the baby faces the rear of the stroller, onto
the Snap-N-Go attachment system so that the large groove on
the seat bottom rests on the Snap Bar.
Snap Bar
Position “I”
2. Rotate the car seat handle toward the foot end of the seat until
locked into place. Loop the two ends of the Car Seat Strap
(attached to the Snap-N-Go frame) over the car seat handle and
snap the two buckles together (see Figure 2). The first time
you do this, you will need to adjust the length of the strap for
a tight fit around the car seat. FOR SAFE OPERATION, IT
IS VERY IMPORTANT THAT THE CAR SEAT STRAP
IS ALWAYS TIGHTLY FASTENED AROUND THE CAR
SEAT.
Figure 1.
3. Test for secure installation by moving the car seat in all
directions. The car seat should be securely attached to the
stroller.
®
®
Removal of Peg Perego Primo Viaggio Infant Car
Seat
1. Unlock the Car Seat Strap and remove both ends from over the
car seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and with your other hand squeeze the grey handle on
the back of the car seat and lift the car seat upward from the
Snap-N-Go attachment system.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Evenflo Cozy Carry
®
Please follow the following instructions for proper installation of
your infant car seat.
Position “5”
®
®
Installation of the Evenflo Cozy Carry Infant Car
Seat
1. Place front seat in the reclined position. With one hand grasp
the car seat handle (in its upright, carrying position) and gently
place the seat, so that the baby faces the rear of the Stroller, onto
the Snap-N-Go attachment system so that the large groove on
the seat bottom, nearest the head-end of the seat, hooks over the
Snap Bar. Check that the seat locked onto the Snap Bar.
2. Loop the two ends of the Car Seat Strap (attached to the Snap-
N-Go frame) over the car seat, half way between the handle and
the foot-end of the seat, and snap the two buckles together (see
Figure 3). The first time you do this, you will need to adjust the
length of the strap for a tight fit around the car seat. FOR SAFE
OPERATION, IT IS VERY IMPORTANT THAT THE CAR
SEAT STRAP IS ALWAYS TIGHTLY FASTENED OVER
THE CAR SEAT.
Snap Bar
Position “I”
Figure 1.
3. Test for secure installation by moving the car seat in all directions.
The car seat should be securely attached to the stroller.
®
Removal of the Evenflo Cozy Carry Infant Car Seat
®
1. Unlock the Car Seat Strap and remove from over the infant car
seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and with your other hand squeeze the red handle on the
back of the car seat and lift the car seat upward from the Snap-
N-Go frame.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Evenflo On My Way
®
Please follow the following instructions for proper installation of
your infant car seat.
®
®
Position “1”
Installation of the Evenflo On My Way Infant Car
Seat
1. Place front seat in the reclined position. With one hand grasp
the car seat handle (in its upright, carrying position) and gently
place the seat, so that the baby faces the rear of the Stroller, onto
the Snap-N-Go attachment system so that the large groove on
the seat bottom, nearest the head-end of the seat, hooks over the
Snap Bar. Check that the seat locked onto the Snap Bar.
2. Feed the Car Seat Straps through the auto belt slots on the
infant car seat and snap the two buckles together (see Figure
2). The first time you do this, you will need to adjust the length
of the strap for a tight fit around the car seat. FOR SAFE
OPERATION, IT IS VERY IMPORTANT THAT THE CAR
SEAT STRAP IS ALWAYS TIGHTLY FASTENED OVER
THE CAR SEAT.
Snap Bar
Position “V”
Figure 1.
3. Test for secure installation by moving the car seat in all directions.
The car seat should be securely attached to the stroller.
®
Removal of the Evenflo On My Way Infant Car Seat
®
1. Unlock the Car Seat Strap and remove from over the infant car
seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and with your other hand squeeze the red handle on the
back of the car seat and lift the car seat upward from the Snap-
N-Go frame.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Evenflo Embrace
®
Please follow the following instructions for proper installation of
your infant car seat.
Position “4”
®
Installation of the Evenflo Embrace Infant Car Seat
®
1. Place front seat in the reclined position. With one hand grasp
the car seat handle (in its upright, carrying position) and gently
place the seat, so that the baby faces the rear of the Stroller, onto
the Snap-N-Go attachment system so that the large groove on
the seat bottom, nearest the head-end of the seat, hooks over the
Snap Bar. Check that the seat locked onto the Snap Bar.
2. Loop the two ends of the Car Seat Strap (attached to the Snap-
N-Go frame) over the car seat, half way between the handle and
the foot-end of the seat, and snap the two buckles together (see
Figure 2). The first time you do this, you will need to adjust the
length of the strap for a tight fit around the car seat. FOR SAFE
OPERATION, IT IS VERY IMPORTANT THAT THE CAR
SEAT STRAP IS ALWAYS TIGHTLY FASTENED OVER
THE CAR SEAT.
Snap Bar
Position “I”
Figure 1.
3. Test for secure installation by moving the car seat in all directions.
The car seat should be securely attached to the stroller.
®
Removal of the Evenflo Embrace Infant Car Seat
®
1. Unlock the Car Seat Strap and remove from over the infant car
seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and with your other hand squeeze the red handle on the
back of the car seat and lift the car seat upward from the Snap-
N-Go frame.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Century Vante
®
Please follow the following instructions for proper installation of
your infant car seat.
Position “1”
®
Installation of the Century Vante Infant Car Seat
®
1. Place front seat in the reclined position. With one hand grasp
the car seat handle (in its upright, carrying position) and gently
place the seat, so that the baby faces the rear of the Stroller, onto
the Snap-N-Go attachment system so that the large groove on
the seat bottom, nearest the head-end of the seat, hooks over the
Snap Bar. Check that the seat locked onto the Snap Bar. See
Figure 1.
Snap Bar
Position “IV”
2. Feed the Car Seat Straps through the auto belt slots on the
infant car seat and snap the two buckles together (see Figure
2). The first time you do this, you will need to adjust the length
of the strap for a tight fit around the car seat. FOR SAFE
OPERATION, IT IS VERY IMPORTANT THAT THE CAR
SEAT STRAP IS ALWAYS TIGHTLY FASTENED OVER
THE CAR SEAT.
Figure 1.
3. Test for secure installation by moving the car seat in all directions.
The car seat should be securely attached to the stroller.
®
Removal of the Century Vante Infant Car Seat
®
1. Unlock the Car Seat Strap and remove from over the infant car
seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and with your other hand squeeze the red handle on the
back of the car seat and lift the car seat upward from the Snap-
N-Go frame.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Graco Snug Ride
Please follow the following instructions for proper installation of
your infant car seat.
Position “1”
®
Installation of the Graco Snug Ride Infant Car Seat
®
1. Place front seat in the reclined position. With one hand grasp
the car seat handle (in its upright, carrying position) and gently
place the seat, so that the baby faces the rear of the Stroller, onto
the Snap-N-Go attachment system so that the large groove on
the seat bottom, nearest the head-end of the seat, hooks over the
Snap Bar. Check that the seat locked onto the Snap Bar.
2. Move Car Seat Straps to the rear location as shown in Figure
2. Feed the Car Seat Straps through the auto belt slots on the
infant car seat and snap the two buckles together (see Figure
3). The first time you do this, you will need to adjust the length
of the strap for a tight fit around the car seat. FOR SAFE
OPERATION, IT IS VERY IMPORTANT THAT THE CAR
SEAT STRAP IS ALWAYS TIGHTLY FASTENED OVER
THE CAR SEAT.
Snap Bar
Position “III”
Figure 1.
3. Test for secure installation by moving the car seat in all directions.
The car seat should be securely attached to the stroller.
®
Removal of the Graco Snug Ride Infant Car Seat
®
1. Unlock the Car Seat Strap and remove from over the infant car
seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and with your other hand squeeze the red handle on the
back of the car seat and lift the car seat upward from the Snap-
N-Go frame.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cosco Arriva
Please follow the following instructions for proper installation of
your infant car seat.
Position “1”
®
Installation of the Cosco Arriva Infant Car Seat
®
1. Place front seat in the reclined position. With one hand grasp
the car seat handle (in its upright, carrying position) and gently
place the seat, so that the baby faces the rear of the Stroller, onto
the Snap-N-Go attachment system so that the seat bottom rest
within the frame.
2. Feed the Car Seat Straps through the auto belt slots on the
infant car seat and snap the two buckles together (see Figure
2). The first time you do this, you will need to adjust the length
of the strap for a tight fit around the car seat. FOR SAFE
OPERATION, IT IS VERY IMPORTANT THAT THE CAR
SEAT STRAP IS ALWAYS TIGHTLY FASTENED OVER
THE CAR SEAT.
Snap Bar
Position “I”
Figure 1.
3. Test for secure installation by moving the car seat in all directions.
The car seat should be securely attached to the stroller.
®
Removal of the Cosco Arriva Infant Car Seat
®
1. Unlock the Car Seat Strap and remove from over the infant car
seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and lift the car seat upward from the Snap-N-Go
frame.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Baby Trend Latch-Loc, Flex-Loc
Please follow the following instructions for proper installation of your
infant car seat.
®
®
Installation of the Baby Trend Latch-Loc Infant Car
Seat
BT BAR
1. Remove (unscrew) the Snap Bar from the Snap N Go attachment.
2. With one hand grasp the car seat handle (in its upright, carrying
position) and gently place the seat, so that the baby faces the rear
of the Stroller, onto the Snap-N-Go attachment system so that the
large groove on the seat bottom, nearest the head-end of the seat,
hooks over the BT Bar.
Position “4”
3. Feed the Car Seat Straps through the auto belt slots on the infant
car seat and snap the two buckles together (see Figure 2). The first
time you do this, you will need to adjust the length of the strap
for a tight fit around the car seat. FOR SAFE OPERATION, IT
IS VERY IMPORTANT THAT THE CAR SEAT STRAP IS
ALWAYS TIGHTLY FASTENED OVER THE CAR SEAT.
4. Test for secure installation by moving the car seat in all directions.
The car seat should be securely attached to the stroller.
Figure 1.
®
Removal of the Baby Trend Latch-Loc Infant Car Seat
®
1. Unlock the Car Seat Strap and remove from over the infant car
seat.
2. With one hand, grasp the car seat handle (in its upright, carrying
position) and with your other hand squeeze the handle on the
footend of the car seat and lift the car seat upward from the Snap-
N-Go frame.
Figure 2.
Cosco®, Peg Perego®, Primo Viaggio®, Evenflo®, Cozy Carry®, On my Way®, Embrace®,
Century®, Vante®, Graco®, Cosco® Arriva® and Snug Ride® are the trademarks of their owners.
They are not associated with Baby Trend, Inc. and no approval or endorsement is implied.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|