ACC-30
DIGITAL AUDIO 6 DISC
COMPACT DISC CHANGER
MODEL ACC-30
6-DISC CD CHANGER
INSTALLATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLING THE UNIT
Transport Lock Screws
The mechanism in the CD changer is "locked" into place during shipment by the 4
transport screws. Be sure to remove the screws prior to installation.
Retainthesescrewsforfutureusewhentransportingtheunitforservice/maintenance.
l Caution l
After removing the transport lock screws, place the supplied seals over the screw
holes. These seals are used to keep dust out of the unit, which could cause a
malfunction.
Installation and Wiring Precautions
To prevent a short-circuit,
l Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation.
l Connect power wires last.
1
Note
If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect
the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra
caution during installation, not to cause a short circuit.
Do not install the unit in the following locations.
l Locations exposed to direct sunlight.
l Where hot air is discharged from the car heater.
l In areas subject to extreme temperatures.
2
Incorrect installation can cause the sound to "skip" when playing a disc.
Mount the unit firmly in place, using the supplied brackets and screws.
3
Be careful not to damage the car wiring.
4
l Be sure to use the supplied screws.
l Be careful not to snag any wires when tightening screws.
l Do not use any of the screws that are part of the brake or steering system, to install the unit.
5
l This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning
6
of the mechanism.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must
correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration
compensation will not be effective and vibration may cause the disc to skip.
HORIZONTAL INSTALLATION
Set the anti-vibration springs to
position "H".
VERTICAL INSTALLAITON
Set the anti-vibration springs to
position "V".
45° ANGLE INSTALLATION
Set the anti-vibration springs to
position "45°".
position "H"
position "45°"
position "V"
H
45°
V
45°
PROCEDURE FOR HORIZONTAL INSTALLATION
1
Attach a mounting bracket to each side of the unit, using the
4 hex head bolts with washer base.
H
45°
V
Bracket
NOTE: Make sure anti-vibration springs
are set to position "H".
Hex head bolt
with washer base
Bracket
2
Determine the mounting location, and drill four mounting
holes.
NOTE: If mounting surface is carpeted, use caution
when drilling holes to prevent drill bit from
catching on carpet. Cut holes in carpet
before drilling into sub-surface.
Drill holes 1/8" (4mm) in diameter.
Self-tapping Phillips head screw
Never mount the unit near the fuel tank.
3
Secure the unit in place, using four self-tapping Phillips
head screws.
Use RTV (silicone sealer) on screw threads or around
the holes to prevent moisture intrusion.
Bracket
Bracket
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PROCEDURE FOR VERTICAL INSTALLATION
Note
If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2.
Set the anti-vibration springs to position "V".
Attach a mounting bracket to each side of the unit, using
the hex head bolts with washer base.
1
2
position "V"
Bracket
Bracket
Hex head bolt
with washer base
Determine the mounting location, and drill four mounting
holes.
Mount the unit in place, using four self-tapping Phillips head
screws.
4
3
Use RTV (silicone sealer) on screw threads or around
the holes to prevent moisture intrusion.
NOTE: If mounting surface is carpeted, use caution
when drilling holes to prevent drill bit from
catching on carpet. Cut holes in carpet
before drilling into sub-surface.
Self-tapping
Phillips head
screw
Never mount the unit near the fuel tank.
Bracket
Bracket
Drill holes 1/8" (4mm) in diameter
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PROCEDURE FOR 45° ANGLE INSTALLATION
Note
If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2.
Set the anti-vibration springs to position "45°".
Attach a mounting bracket to each side of the unit, using
the 4 hex head bolts with washer base.
1
2
position "45°"
Bracket
Bracket
Hex head bolt
with washer base
45°
Determine the mounting location, and drill four mounting
holes.
Mount the unit in place, using four self-tapping Phillips head
screws.
4
3
Use RTV (silicone sealer) on screw threads or around
the holes to prevent moisture intrusion.
NOTE: If mounting surface is carpeted, use caution
when drilling holes to prevent drill bit from
catching on carpet. Cut holes in carpet
before drilling into sub-surface.
Self-tapping Phillips head screw
Never mount the unit near the fuel tank.
Bracket
Bracket
Drill holes 1/8" (4mm) in diameter
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING
Mating 8-pin DIN socket on rear of
compatible radio chassis (see Note below).
Car Stereo with
CD Changer Controls
CD changer
NOTE: 1. Check with your Rampage/Audiovox audio dealer
to be sure your stereo is directly compatible with
this CD changer.
2. When used with Rampage model AV-427 car
stereo, besureChangerSelectorswitchonbottom
of radio chassis is set to position "B".
6
Download from Www.Somanuals.com. All Manuals Search And Download.
© 1999 Audiovox Corporation, Happauge, N.Y. 11788
Printed in Korea
128-5572
Download from Www.Somanuals.com. All Manuals Search And Download.
|