Model PRO 9232S
OWNER’S MANUAL
KEYLESS ENTRY ALARM UPGRADE MODULE
Congratulations on your purchase of the PRO 9232S automotive Keyless Entry
Upgrade Alarm System. The PRO 9232S is a state -of -the-art auto security system
that is designed to automatically arm and disarm when it receives a command from
your existing Factory Keyless Entry Transmitter. Taking a few moments to read this
manual will help to ensure that your vehicle is protected at all times.
ARMING THE SYSTEM: (ACTIVE)
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. Press and release the Lock button on the keychain transmitter.
3. The siren and or horn will beep one time, the parking lamps will flash one
time, and the red dash mounted LED will begin to slowly flash, indicating
that the system is ARMED.
NOTE: If the unit beeps three times when arming, then one of the entry
points ( hood, trunk, or doors ) has been left opened. Closing the
hood, trunk, or door will correct the problem, and the system will
emit a single chirp to confirm that the problem has been corrected.
Additionally, if illuminated entry is a feature of the Factory Keyless
Entry system, the alarm may chirp 3 times every time the system is
armed, and chirp one additional time when the interior light turns off
to confirm that all trigger zones are fully operational.
4. Any time the door lock switch in the vehicle is used to lock the doors while
the ignition key is turned off, the system will immediately arm. To lock the
doors after entering the vehicle, make sure the ignition key is switched on
first. Turning the ignition key on first will stop the system from arming.
ARMING THE SYSTEM: (PASSIVE)
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. The dash-mounted LED will begin to flash rapidly, indicating that the
system is automatically ( passively ) arming. As an added convenience,
the 30 second automatic passive arming will not begin until all doors are
closed, allowing passengers to exit the vehicle at their convenience.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISARMING THE SYSTEM:
1. As you approach the vehicle, press and release the unlock button on the
keychain transmitter.
2. The siren and or horn will beep two times, the parking lamps will flash two
times, and the red dash mounted LED will turn off, indicating that the
system is DISARMED. If the optional entry illumination feature has been
installed, the vehicle’s interior lights will turn on for 30 seconds,
or until the ignition key is turned on.
NOTE: If your system has been programmed for “ passive arming “, then it
will begin to re-arm immediately after disarming. This is indicated by
a rapid flashing of the red dash mounted LED Opening one of the
vehicle’s doors will suspend the passive arming process until all
doors have been closed, or until the ignition key has been turned on.
INTRUSION WARNING SIGNALS:
The system will inform you if an intrusion attempt has occurred while you were
away from the vehicle. If an intrusion attempt has occurred, the siren and or horn
will beep four times when the system is disarmed. The vehicle’s parking lights will
also flash three times to indicate an intrusion has occurred.
Enter the vehicle and observe the dash mounted LED for further information.
1. If the LED is flashing one time...pause...one time...pause...etc., then an
intrusion attempt was made to a voltage sensing, light activated entry
point, or to an optional sensor that has been connected to zone 1.
2. If the LED is flashing two times...pause...two times...pause...etc., then an
intrusion attempt was made to the hood or trunk, or to an optional sensor
that has been connected to zone 2.
3. If the LED is flashing three times...pause...three times...pause...etc.,
then an intrusion attempt was made through one of the vehicle’s doors.
These intrusion warning indicators are stored in the system’s memory, and will
only be erased when the ignition key is turned to the “ on “ position.
OPERATING THE EMERGENCY PANIC:
The buttons on your keychain transmitter will allow you to immediately activate the
alarm in emergency situations. To use the remote panic switch:
1. Press the unlock, then lock, then unlock buttons on your keychain
transmitter within 3 seconds. The alarm will immediately sound, and
continue to sound for 30 seconds.
2. To stop the alarm before the 30 second cycle has expired, simply press
and release the unlock button on your keychain transmitter.
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE VALET SWITCH:
The valet switch allows you to temporarily bypass all alarm functions, eliminat-
ing the need to hand your transmitter to parking attendants or garage mechan-
ics. When the system is in valet mode, all alarm functions are bypassed, how-
ever the remote panic feature and remote door locks will remain operational. To
use the valet mode, the system must first be disarmed either by using your
keychain transmitter, or by activating your personalized manual override code.
TO ENTER THE VALET MODE:
1. Disarm the unit by use of the factory transmitter or by use of the
manual override sequence.
2. Turn the ignition switch to the “On” position.
3. Press and hold the valet/override pushbutton switch for 5 seconds.
The LED turns on, indicating valet mode has been successfully
entered.
TO EXIT THE VALET MODE:
With the ignition switch in the on position, press and release the valet/override
pushbutton switch one time. The LED turns off indicating the valet mode has
successfully been exited.
MANUAL OVERRIDE OPERATION:
If your factory transmitter is lost, broken, or otherwise rendered inoperable, your
system can be overriden allowing operation of the vehicle. The manual
override code is pre-programmed at the factory to 11. This code can be
changed by the operator to a more familar two digit number. Once you’ve
become familiar with the system’s operation and override proceedure, we
suggest you change the code for added security.
NOTE: The override proceedure below describes use, assuming that the
factory pre-set code has not been been changed and is still set to the
factory default 11. The valet/override push button switch is used to
enter the tenths and units digits, pressing and releasing this button
one time for each digit required.
To manually overrride your system,with a code of 11, follow the sequence listed
below:
1. The LED is flashing indicating unit is armed, enter the vehicle, the
siren will sound, turn the ignition switch to the “on” position.
2. Within 10 seconds begin to enter tenths digit of override code. (In this
example the code is 11, so press and release the Valet/Override
pushbutton one time).
3. Within 10 seconds of entering the last tenths digit, turn ignition “off
then on”.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Within 10 seconds of turning the ignition switch on, begin to enter
units digit of override code. (In this example the code is 11, so press
and release the Valet/Override pushbutton one time).
5. Within 5 seconds after the last units digit is entered, turn the
ignition switch off, then on, and start your vehicle.
If the manual override code is entered properly, the unit stops sounding, the
LED turns off, indicating a successful override. The system is now disarmed
and you can start and operate your vehicle. The unit will allow three attempts to
disarm via the manual override sequence. If the code is not successfully
entered within the three attempts, disarming with the manual override switch
will be locked for 10 minutes.
In many cases, to increase the security of your system, you may elect to
change the manual override code to a number that is more familiar to you, or
simply to have a different code than was pre-assigned from the factory. To
Change the pre-assigned override code follow the steps outlined below.
It is advised you read both sections under the headings “Programming Your
Custom Override Code” and, “Custom Code Programming Example”, To
completely understand the proceedure before beginning:
PROGRAMMING YOUR CUSTOM OVERRIDE CODE:
Unlike override switches easily found, and defeated, the PRO-9232S allows
the consumer to program a personal override code, offering a higher level of
security. The system comes from the factory with a pre-programmed override
code of 11. To change this default override code, do the following:
1. Disarm the system by use of the transmitter, or by use of the emer
gency override sequence. Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the valet/override switch, 3
times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing
and releasing thepushbutton switch from 1up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition
switch off then on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing
and releasing thepushbutton switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the off position.
If the new code was accepted, the unit will report back the newly entered code,
by flashing the LED, first indicating the 10ths digit, pause and then the units
digit. The unit will report the new code three times with a one second pause
between each code, then the system will begin arming. If the LED flash
Download from Www.Somanuals.com. All Manuals Search And Download.
pattern reports the previously stored code, the new code was not entered
correctly. Please repeat steps 1 through 7 above considering the following.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not
recognize a 0 (Zero), or no digit entered in any place, units or
tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned
off for more then 5 seconds during any of the above steps, the
unit will revert back to the last success fully stored code.
CUSTOM CODE PROGRAMMING EXAMPLE:
To Change the code from the factory pre-assigned code of 11 to “52” you
would do the following:
1. Disarm the system by use of the transmitter, or by use of the emer
gency override sequence.
2. Turn the ignition switch to the on position.
3. Within 10 seconds, press and release the valet/override switch, 3
times.
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
5. Within 10 seconds, begin to press and release the push button
switch to set the tenths digit. (As per the example, press and release
5 times to set the tenths digit to 5.)
6. Within 10 seconds of the last press of the push-button, turn the
igntion switch off then on.
7. Within 10 seconds, begin to press and release the push button
switch to set the units Digit. (As per the example, press and release 2
times to set the units digit to 2.)
8. Turn the ignition switch to the off position. Immediately observe the
LED flash pattern.
You will note the LED flashing five times, pause, and then flash two times,
pause. This pattern will be repeated three times indicating the new code (52)
has been accepted and stored in memory.
NOTE: If after step 7, the LED flashes a code other than what was just
entered, this indicates that the code has not been changed. You will
have to repeat steps 1 through 7 above being certain to note the
following:
Acceptable digits 10ths or units are 1 through 9. The unit will not
recognize a 0 (Zero), or no digit entered in any place, units or
tenths.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch
is turned off for more then 5 seconds during any of the above steps,
the unit will revert back to the last success fully stored code.
ADDITIONAL REMOTE FUNCTION:
This system allows the control of any one of the following optional accessories;
Remote Car Starter
Remote Window Closure
Remote Window Open
To operate the optional accessory;
1. Press the lock, then unlock, then lock buttons on your keychain transmit
ter within 3 seconds.
2. The optional accessory will immediately activate.
OPTIONAL AUTO LOCK/UNLOCK FEATURE:
If your existing factory installed keyless entry system did not include the automatic
door lock and unlock feature, then this feature can be activated from the PRO 9232
upgrade module. When this accessory has been added, any time the ignition key
is turned to the on position and all vehicle doors are closed, the doors will lock
in 4 seconds. Additionally, any time the ignition key is turned to the off position,
the doors will unlock.
ELIMINATING THE ARM/DISARM CHIRPS:
The normal arming and disarming confirmation chirps can easily be turned
off using the valet pushbutton switch. To do this:
1. Turn the ignition key on, and then off.
2. Within 10 seconds of turning the ignition key off,press and release the
valet switch 3 times.
3. a. If, before proceeding with step 1, the chirps were on, then you will
hear 2 chirps to indicate that the chirps have been turned off.
b
If, before proceeding with step 1, the chirps were off, then you will
hear 1 chirp to indicate that the chirps have been turned on.
4. Whenever power to the system has been disconnected ( for repair or
service to the vehicle ), the chirps will be activated when the power is
re - connected. To turn the chirps off, simply execute steps 1 through
3 above.
NOTE: WhenevertheArm/Disarmchirpsareby-passed,the3chirpdefective
zone and the 4 chirp intrusion indicator will always operate. This
featurewillalwayswarnyouifadoorwasleftajarwhenarming, orthe
vehicle was tampered with in your absence.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO 9232S
SYSTEM FUNCTIONS AT A GLANCE
DASH L.E.D. INDICATORS
RAPID FLASHING ..........................................................
SLOW FLASHING ...........................................................................
OFF ...........................................................................................
ON - SOLID ............................................................................
PASSIVE ARMING
ARMED
DISARMED
VALET MODE
3 FLASH ... PAUSE .....................................................
2 FLASH ... PAUSE .....................................................
1 FLASH ... PAUSE .....................................................
INTRUSION ZONE 3
INTRUSION ZONE 2
INTRUSION ZONE 1
CHIRP INDICATORS
1 CHIRP * ............................................................................................
ARM
DISARM
ARM / DOOR OPEN
2 CHIRPS* .....................................................................................
3 CHIRPS ...................................................................
3 CHIRPS .......................................
4 CHIRPS .................................................................
10 MIN. PASSIVE ARM / DOOR OPEN
DISARM / INTRUSION
DISARM / AFTER 10 MIN.
PASSIVE ARM
2 SHORT CHIRPS - 1 LONG CHIRP....................
4 SHORT CHIRPS - 1 LONG ................................
DISARM / AFTER 10 MIN.
PASSIVE ARM AND INTRUSION
* These chirps are optional, and can be de-activated.
PARKING LAMPS
1 FLASH ................................................................................................ ARM
2 FLASH ......................................................................................... DISARM
3 FLASH ................................................................... DISARM / INTRUSION
Your System Has These Features Activated:
Starter Disable When Armed
Passive Arming
Instant Trigger
Remote Car Starter
Remote Window Open
Remote Window Closure
Key Activated Auto Lock/Unlock
Shock Detector
Motion Detector
Hardwire
q
q
q
q
q
q
q
q
q
q
Audiovox Corp.
150 Marcus Blvd.
Hauppauge, N.Y. 11788
Form No. 128-6021
Download from Www.Somanuals.com. All Manuals Search And Download.
|