Washer-Extractors
Pocket Hardmount
Variable-Speed
WE-6 Control
3
2
1
6
5
4
9
8
7
0
1
9
PHM1
PHM1389C
UW35PV – UW125PV
PHM1390CN
UW150PV
Para bajar una copia de estas instrucciones
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F232084R16
May 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information..............................................................................
Operator Safety.....................................................................................
2
Table of
Contents
Introduction.........................................................................................
6
Specifications and Dimensions...........................................................
8
Mounting Bolt Installation Requirements
(Approved Foundations Only)............................................................ 18
Grout Placement ................................................................................... 25
Water Connection................................................................................. 29
Designs 1-4 ...................................................................................... 39
© Copyright 2008, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F232084
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
DANGER
1. Read all instructions before using the washer.
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, dry-
cleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas is
flammable, do not smoke or use an open flame
during this time.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
2
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
20. If the supply cord is damanged, it must be
replaced by a special cord or assembly available
from the manufacturer or its service agent.
10. Do not tamper with the controls.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
connect the washer to the electrical power source.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a qualified
service person.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
3
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
SW025
WARNING
damage, and may void the warranty.
SW004
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
IMPORTANT: Ensure that the recommended
clearaces for inspection and maintenance are
provided. Never allow the inspection and
maintenance space to be blocked.
the pipe can be touched.
SW014
CAUTION
Safety Decals
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
damage.
W703
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
4
Safety Information
Do not bypass any safety devices in the machine.
Operator Safety
WARNING
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
SW012
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
damage.
SW039
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
5
Introduction
Model Identification
MODEL EXAMPLE OF NAMEPLATE LOCATION
Information in this manual is applicable to these
models:
3
1
UW35PV
UW80PV
UW125PV
UW60PV
UW100PV
UW150PV
2
This manual is designed as a guide to the installation
of the Pocket Hardmount washer-extractor equipped
with the AC inverter drive.
P
U
S
H
NOTE: All information, illustrations, and
specifications contained in this manual are based
on the latest product information available at the
time of printing. We reserve the right to make
changes at any time without notice.
PHM618N
1
2
Near Supply Valves on Cagewrap
Below Inverter Exhaust Fan on Electric Heat
Box (if equipped)
Delivery Inspection
Upon delivery, visually inspect crate, protective cover,
and unit for any visible shipping damage. If the crate,
protective cover, or unit is damaged or signs of
possible damage are evident, have the carrier note the
condition on the shipping papers before the shipping
receipt is signed, or advise the carrier of the condition
as soon as it is discovered.
3
Side of AC Drive Compartment-
Figure 1
Replacement Parts
If literature or replacement parts are required, contact
the source from which the washer-extractor was
purchased or contact Alliance Laundry Systems LLC
at (920) 748-3950 for the name of the nearest
authorized parts distributor. A parts manual may be
ordered by returning the reply card provided with each
washer-extractor.
Remove the crate and protective cover as soon after
delivery as possible. If any damage is discovered upon
removal of the crate and/or protective cover, advise the
carrier and file a written claim immediately.
Nameplate Location
The nameplate is located on cagewrap, on side of AC
Inverter Drive Compartment and on Electric Heat
Contractor Box (if equipped). Always provide the
machine’s serial number and model number when
ordering parts or when seeking technical assistance.
Customer Service
For technical assistance, contact your local distributor
or call:
(920) 748-3121
Ripon, Wisconsin
A record of each washer-extractor is on file with the
manufacturer. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance. Refer to Figure 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
6
Introduction
Model Number Familiarization Guide
Sample Model Number: UW60PVQU80001
Model Number Prefix
Washer-Extractor Capacity (pounds dry weight of laundry)
UW
60
Type of Electrical Control
Washer-Extractor Speed Capabilities
Electrical Characteristics
Design Series
P = WE-6 Computer
V = 7 Speeds
P
V
Q
J = Jog Feature (UW150 Models only)
U8
0001
Option Identification (varies from machine to machine)
UW60PVQU80001
00000000000
200 – 240
19
30
50 – 60
60
3
3
720
27
500000
EXAMPLE OF NAMEPLATE
PHM587N
Figure 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
.
UWPV Models
Specifications
35
60
80
100
125
150
Overall Dimensions
Overall width, in (mm)
Overall height, in (mm)
Overall depth, in (mm)
32.5 (826)
55.5 (1410)
43.63 (1108)
36.63 (930)
64.5 (1638)
45 (1143)
41.5 (1054)
68.5 (1740)
51.5 (1308)
41.5 (1054)
68.5 (1740)
54.5 (1384)
48 (1219)
72 (1829)
58 (1473)
50.25 (1277)
79 (2007)
63 (1600)
Weight And Shipping Information
Net weight, lb (kg)
1030 (468)
1300 (590)
200 (92)
1730 (785)
330 (150)
1795 (814)
119 (3.4)
1770 (805)
360 (163)
1835 (832)
119 (3.4)
2420 (1100)
550 (250)
2970 (1347)
572 (260)*
3022 (1371)
172 (4.87)
Basket Weight, lb (kg)
150 (68)
1085 (493)
66 (1.9)
Domestic shipping weight, lb (kg)
1340 (608)
84 (2.4)
2525 (1148)
166 (4.7)
Domestic shipping volume,
ft3 (m3)
38x47x64
(970x1200x
1630)
40x49x74.5
(1016x1245x
1892)
44x60.5 x77.25
(1118x1537x
1962)
44x60.5x77.25
(1118x1537x
1962)
61.5x60x77.75
(1560x1520x
1980)
54.5x69x79
(139x176x
201)
Domestic shipping dimensions,
WxDxH, in (mm)
Export shipping weight, lb (kg)
Export shipping volume, ft3 (m3)
1150 (522)
78 (2.2)
1464 (664)
96 (2.7)
1990 (903)
134 (3.8)
2030 (921)
134 (3.8)
2800 (1270)
184 (5.3)
3350 (1520)
220 (6.3)
41x50x65.5
(1050x1280x
1670)
43x52.12x74.5
(1092x1324x
1892)
47x63.5x77.25
(1194x1613x
1962)
47x63.5x77.25
(1194x1613x
1962)
63.5x63x80
(1620x1610x
2030)
61.5x71x87
(1562x1804x
2210)
Export shipping dimensions,
WxDxH, in (mm)
Wash Cylinder Information
Cylinder diameter, in (mm)
Cylinder depth, in (mm)
26.25 (667)
18.38 (467)
5.76 (163)
0.19 (4.8)
18
32 (813)
20 (508)
9.31 (264)
0.19 (4.8)
22
36 (914)
21 (533)
12.4 (350)
0.19 (4.8)
23
36 (914)
27 (686)
15.9 (450)
0.19 (4.8)
23
42 (1067)
24 (610)
19.2 (544)
0.19 (4.8)
24
43 (1093)
27.81 (706)
23.4 (662)
0.19 (4.8)
21.5
Cylinder volume, ft3 (l)
Perforation size, in (mm)
Perforation open area,%
Door Opening Information
Door opening size, in (mm)
14.34 (364)
23.75 (603)
17.5 (445)
17.5 (445)
29 (737)
17.5 (445)
29 (737)
20 (508)
29 (737)
24.75 (629)
32 (813)
Height of door bottom above floor,
in (mm)
28.25 (718)
Drive Train Information
Number of motors in drive train
Drive motor power, hp (kW)
* Basket Only
1
1
1
1
1
1
3.0 (2.2)
5.0 (3.7)
7.5 (5.6)
7.5 (5.6)
10 (7.5)
10 (7.5)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
UWPV Models (Continued)
Specifications
35
60
80
100
125
150
Cylinder Speeds / Centrifugal Force Data
1/2 Wash/reverse, rpm (g)
Wash/reverse, rpm (g)
Distribution, rpm (g)
26 (.25)
42 (.66)
26 (.31)
40 (.73)
26 (.35)
40 (.82)
26 (.35)
40 (.82)
26 (.40)
37 (.82)
62 (2.29)
260 (40)
380 (86)
N/A
23 (.31)
36 (0.8)
83 (2.57)
325 (39)
474 (84)
533 (106)
610 (139)
795 (235)
897 (308)
71 (2.29)
305 (42)
435 (86)
483 (106)
555 (140)
720 (235)
813 (300)
73 (2.57)
325 (54)
408 (85)
456 (106)
523 (140)
671 (230)
767 (300)
70 (2.50)
325 (54)
408 (85)
456 (106)
523 (140)
601 (184)
767 (300)
61 (2.29)
262 (42)
417 (106)
417 (106)
512 (160)
573 (200)
701 (300)
Medium extract, rpm (g)
High extract l, rpm (g)
*Design U6 models
High extract 2, rpm (g)
485 (140)
534 (170)
580 (200)
High extract 3, rpm (g)
*Design U6 models
Balance Detection
Vibration switch installed
STD
STD
STD
STD
STD
STD
.006 (.15) GO
.008 (.20) NO-
GO
.008 (.20) GO
.010 (.25) NO-
GO
.008 (.20) GO
.010 (.25) NO-
GO
.008 (.20) GO
.010 (.25) NO-
GO
.006 (.15) GO
.008 (.20) NO-
GO
.013 (.33) GO
.014 (.30) NO-
GO
Switch gap setting, in
(mm)**
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
Direct Steam Heating (Optional)
Steam inlet connection size,
in (mm)
1/2 (13)
1/2 (13)
1/2 (13)
1/2 (13)
3/4 (19)
3/4 (19)
Number of steam inlets
1
1
1
1
1
1
LO
W
2.1 (1.5)
3.3 (2.4)
4.6 (3.3)
5.7 (4.1)
6.7 (4.9)
8.3 (6.0)
Steam required to
raise bath
ME
D
2.3 (1.7)
2.7 (1.9)
1.4 (21.4)
3.7 (2.6)
4.1 (2.9)
2.1 (33.4)
5.2 (3.8)
6.1 (4.4)
3.1 (48.4)
6.5 (4.7)
7.6 (5.5)
3.8 (60.4)
7.8 (5.6)
9.1 (6.6)
4.6 (72.0)
9.5 (6.9)
11.1 (8.0)
5.8 (91.0)
temperature
10°F, lb (10°C, kg)
HIG
H
Average consumption per
cycle, BHP (kg)
Electrical Heating (Optional)
Total electrical heating
capacity, kW
15.6
25.2
6
37.8
9
37.8
9
50.4
12
N/A
N/A
N/A
N/A
N/A
N/A
Number of electrical heating
elements
6
Electrical heating element
size, kW
2.6
4.2
4.2
4.2
4.2
LO
W
2.4 (3.6)
2.7 (4.1)
3.1 (4.7)
2.4 (3.7)
2.7 (4.1)
3.0 (4.6)
2.2 (3.4)
2.5 (3.9)
3.0 (4.5)
2.8 (4.2)
3.2 (4.8)
3.7 (5.6)
2.5 (3.8)
2.9 (4.4)
3.4 (5.1)
Time required to
raise bath
ME
D
temperature
10°F, min (5°C, min)
HIG
H
*
** Gap setting should be made with “GO–NO-GO” type feeler gauge.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
exact dimensions are required for construction
purposes, contact the distributor or the
manufacturer. We reserve the right to make
changes at any time without notice.
Machine Dimensions
Dimensional Clearances
Allow a minimum of 24 inches (60 cm) at the rear and
18 inches (45 cm) at the sides for maintenance,
inspection, and adjustment. Allow at least 18 inches
(45 cm) between machines in multiple installations.
WARNING
Crush hazard.
To avoid personal injury and/or property
damage, do not tip the UW150 machine
NOTE: The dimensions shown here are for
planning purposes only. They are approximate and
subject to normal manufacturing tolerances. If
more than 25 degrees in any direction.
W642
UWPV Pocket Hardmount Machine Dimensions (Refer to Figure 3 and Figure 4)
35 60 80 100 125
150
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
30.12
33.39
23.75
43.63
1/2
765
847
603
1108
13
35.63
36.63
28.25
45
905
930
718
1143
25
41.12
41.5
29
1045
1054
737
41.12
41.5
29
1045
1054
737
48
48
29
58
1.5
72
48
1219
1219
737
50.25
50.25
32
1277
1277
813
A
1
B
C
D
51-1/2
3
1308
76
54.5
3
1384
76
1473
38
63
1600
73
2
1
2.9
E
55.5
36
1410
914
203
1114
64.5
36
1638
914
394
1397
68-1/2
43-3/4
16-7/8
58-1/2
1740
1111
429
68.5
43-3/4
16-7/8
58-1/2
1740
1111
429
1829
1219
289
79
2007
1422
400
F
2
56
G
H
8
15.52
55
11-3/8
63-3/8
15.75
70
43.88
1486
1486
1610
1778
J
1
Overhang dimensions for the optional starch dispenser are as follows:
UW35PV, 3.88 inches (9.86 cm); UW60PV, 1.75 inches (4.45 cm);
UW80PV and UW100PV, 0.33 inch (0.83 cm). (The starch dispenser does not overhang the UW125PV.) (No longer available.)
The overhang dimension for the premium wet clean module option (compatible with wet-clean-capable washer-extractors only) adds 24 inches (60.96
cm) to combined machine dimensions E and G.
2
Table 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
1
7
2
3
4
5
6
F
E
C
A (BASE)
G (BASE)
B (OVERALL)
D (OVERALL)
13
8
9
10
11
J
12
H
8
UW35PV – UW125PV
PHM607N
1
2
3
4
5
6
7
Emergency Stop Button
Supply Valve Box
Door Unlock Button
Supply Dispenser
Door Handle
8
9
10
11
12
Premium Wet Clean Module (Optional)
Power Input Area (Inside)
Steam Connection (Optional)
Drain
Drain (UW80PV, UW100PV and UW125PV
models only)
Spray Rinse Nozzle
Recirculation Inlet
13
Water Inlet Valves
Figure 3
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
1
2
8
9
1
4
7
1
2
5
8
0
3
6
9
5
4
3
2
1
3
7
6
F
5
J
4
C
A (BASE)
G (BASE)
10
E
D (OVERALL)
B (OVERALL)
11
H
12
UW150PV
PHM603N
1
2
3
4
5
6
Emergency Stop Button
Supply Valve Box
Supply Dispenser
Spray Rinse Nozzle
Basket Jog Button (Optional)
Door Handle
7
8
9
10
11
12
Door Unlock Button
Recirculation Inlet
Water Inlet Valves
Power Input Area (Inside)
Steam Connection (Optional)
Drain
Figure 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
For new foundations a bolt-locator fixture or rebar
frame is available and a preferred option. This rigid
welded assembly made of reinforcing rod and
mounting bolts is designed to be embedded in
Machine Foundation Requirements
A 12 inch (305 mm) thickness of 3500 psi reinforced
concrete foundation is absolutely necessary for all
UWPV washer-extractors because of the high extract
speed and the G-forces exerted.
The washer-extractor must be anchored to a smooth
level surface so that the entire base of the machine is
supported and rests on the mounting surface. (Do not
support the washer-extractor on only four points.)
for Floor Load Data for all model sizes. If the
foundation requirements have been met, proceed to
Mounting Bolt Installation Requirements section.
NOTE: Do not mount on wooden floors, above
ground level, or over basements. Installation must
be “slab on grade” or equal.
Thoroughness of detail must be stressed with all
foundation work to ensure a stable unit installation,
eliminating possibilities of excessive vibration during
extract.
CAUTION
Ensure that the machine is installed on a
level floor of sufficient strength and that
the recommended clearances for
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
SW020
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
14
Specifications and Dimensions
5. Refill with compacted fill dirt, making sure to
allow for correct concrete thickness.
Concrete Foundation Pad
Installation
6. Wet the hole around the cement foundation well
and brush the exposed foundation with cement
grout.
A concrete foundation and pad may be constructed to
elevate the machines. Care must be exercised in the
design of the foundation pad due to the force exerted
by the machine during extract. This concrete base
(recommended not to exceed 8 inches [20.32 cm])
must be poured, reinforced with rebar and tied to the
existing 12 inch (30.48 cm) minimum floor. Refer to
7. Completely fill with a minimum of 12 inches
(305 mm) up to the existing foundation level plus
any added level for the desired elevated pad. The
concrete must be poured so that the entire
foundation and pad cures as one piece.
8. For new foundations only a bolt-locator fixture
or a rebar frame is available and a preferred
option. Embed the mounting bolts or rebar frame
as the concrete is poured. Ensure that the bolt
threads extend 2 inches (51 mm) for UW35 - 125
models and 3 inches (76 mm) for UW150 models
above floor level.
IMPORTANT: Do NOT install a pad on top of the
existing floor. The foundation and pad must be
constructed and tied together as one piece.
If the existing floor is not reinforced concrete at least
12 inches (305 mm) thick over a solid foundation, the
9. Allow concrete to dry.
1. Cut a hole larger on all sides than the machine
base through the existing floor. The foundation
should extend a minimum of 9 inches (229 mm)
for UW35 models or 12 inches (305 mm) for
UW60 - 150 models out from the machine on all
sides.
10. Proceed to Machine Mounting and Grouting
section.
NOTE: If the washer-extractor installation will
include the Premium Wet Clean Module, the
elevated base must be designed to accommodate the
additional depth of 24 inches (60.96 cm).
2. Excavate to a depth of 18 inches (457 mm) from
the top of the existing floor.
For technical assistance, contact your local distributor
or call Alliance Laundry Systems at (920) 748-3121.
3. Produce a PYRAMID-SHAPED hole by
excavating the bottom of the hole to a width 6
inches wider on each side than the width of the
top of the hole.
4. If installing a foundation and pad, prepare a form
for the above-ground portion of the foundation.
Verify that the top of the foundation is level. The
height of the foundation pad must not exceed 8
inches (203 mm) above the existing floor.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
15
Specifications and Dimensions
Brush with
Cement
Grout
Brush with
Cement
Brush with
Cement
Grout
Grout
5
1
3
3
LENGTH FOR ONE
MACHINE
3
3
2
4
6
COMPACTED FILL DIRT 18 in. (457 mm) DEPTH
COMPACTED FILL DIRT18 in. (457 mm) DEPTH
PHM720N
Figure 5
80
35
60
100
125
150
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
1
2*
3
6 in. (152 mm)
minimum
6 in. (152 mm)
minimum
6 in. (152 mm)
minimum
6 in. (152 mm)
minimum
6 in. (152 mm)
minimum
6 in. (152 mm)
minimum
9 in.
(229 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
36 in.
(914 mm)
36 in.
(914 mm)
43.75 in.
(1111 mm)
43.75 in.
(1111 mm)
48 in.
(1219 mm)
47.9 in.
(1217 mm)
4
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
5
6
30.21 in.
(765 mm)
35.62 in.
(905 mm)
41.12 in.
(1044 mm)
41.12 in.
(1044 mm)
48 in.
(1219 mm)
47 in.
(1194 mm)
* Measurement of existing floor.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
Floor Load Data
Static and dynamic loads on the floor or foundation are
floors and foundations.
UWPV Pocket Hardmount Floor Load Data
Design
Series
Specifications
35
60
80
100
125
150
Static floor load, lbs (kN)
U1-U5 1271 (5.64) 1677 (7.45) 2506 (11.2) 2741 (12.2) 3571 (15.9)
3936 (17.5)
U6 and 1272 (5.66) 1677 (7.45) 2292 (10.2) 2490 (11.1) 3283 (14.6)
greater
2
Static pressure, lbs/ft
(kN/m )
U1-U5 169 (8.08) 188 (9.00)
200 (9.6)
219 (10.5)
199 (9.6)
223 (10.7)
205 (9.8)
2
202 (9.7)
4358 (19.4)
224 (11)
U6 and 169 (8.08) 187 (8.94) 184 (8.79)
greater
Dynamic floor load, lbs (kN) U1-U5 1647 (7.3) 2824 (12.6) 3683 (16.38) 3681 (16.37) 5016 (22.31)
U6 and 1648 (7.33) 2824 (12.6) 3679 (16.36) 3690 (16.41) 5011 (22.29)
greater
2
Dynamic pressure, lbs/ft
(kN/m )
U1-U5 219 (10.5) 317 (15.2) 295 (14.2)
294 (14.1)
295 (14.2)
313 (15.1)
312 (15)
2
U6 and 219 (10.5) 317 (15.2) 295 (14.2)
greater
Dynamic load frequency, Hz U1-U5
13.3
15
12
11.2
12.8
10
9.7
9.7
11.7
U6 and
13.6
12.8
greater
1
Maximum vertical load,
lbs (kN)
U1-U5 2712 (12.0) 4184 (18.6) 5493 (24.43) 5551 (24.69) 7561 (33.63)
7508 (33.4)
1208 (5.4)
16707 (22.7)
U6 and 2719 (12.1) 4168 (18.5) 5482 (24.38) 5561 (24.73) 7559 (33.62)
greater
2
Minimum vertical load,
U1-U5 582 (2.59) 1464 (6.50) 1873 (8.3)
1811 (8.1)
2471 (11)
lbs (kN)
U6 and 576 (2.56) 1450 (6.45) 1852 (8.24) 1794 (8.0) 2434 (10.8)
greater
Base moment, lb/ft (kN/m) U1-U5 4250 (5.35) 8894 (11.2) 11853 (16.1) 11849 (16.1) 16702 (22.7)
U6 and 4249 (5.8) 8895 (12.1) 11951 (16.2) 11984 (16.3) 16606 (22.5)
greater
1
Acting in the downward direction against the floor.
2
Acting in the upward direction away from the floor.
Table 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
For new foundations a bolt-locator fixture or rebar
frame is available and a preferred option. This rigid
welded assembly made of reinforcing rod and
mounting bolts is designed to be embedded in
Mounting Bolt Installation
Requirements (Approved
Foundations Only)
NOTE: If installing expansion bolts into an
elevated concrete foundation pad, the concrete
foundation pad should extend a minimum of 9
inches (229 mm) for UW35 machines or 12 inches
(305 mm) for UW60 - 150 machines out from the
1
2
NOTE: The optional Premium Wet Clean Module
does not require permanent attachment to the floor.
3
A bolt kit consisting of eight bolts is available as an
option. UW35PV machines use 5/8-11 x 8 inch bolts.
UW60PV – UW125PV machines use 3/4-10 x 8 inch
bolts. UW150PV machines use 3/4-10 x 10 inch
grade 5 bolts. The bolts should be embedded in a
3500 psi (241 bar) minimum reinforced concrete floor
that is a minimum of 12 inches (30.48 cm) thick. Use
the mounting bolt layouts in Mounting Bolt Hole
Locations section.
4
PHM179N
On UW35PV – UW125PV machines, the threaded end
of the bolts should extend 2 inches (5.08 cm) above
the mounting surface. On UW150PV machines, the
threaded end of the bolts should extend 3 inches above
the mounting surface.
1
2
3
4
Machine Frame Base
Mounting Bolt Threads
Grouting
Reinforcing Rod
mounting bolts.
Figure 7
1
0.75 in.
(19 mm)
2
2 in.
(51 mm)
3
8 in.
(203 mm)
PHM722N
1
2
3
Machine Frame Base
Grout
Cement or Structural Epoxy
Figure 6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
7. Before grout sets completely, make a drain
opening in the rear of the washer-extractor
grouting with a stiff piece of wire; this opening
should be approximately 1/2 inch (1.27 cm) wide
to allow any surface water build-up under the
base of the machine to drain away. Do not omit
this step.
Machine Mounting and Grouting
After the concrete has cured, proceed as follows:
1. Place the washer-extractor adjacent to the
foundation. Do not attempt to move the machine
by pushing on the sides. Always insert a pry bar
or other device under the bottom frame of the
machine to move it.
8. Position the mounting bolt washers and locknuts
on the anchor bolts and fingertighten locknuts to
machine base.
2. Remove the wood skid by unscrewing the
carriage bolts holding the skid to the bottom
frame of the washer-extractor.
9. After the grout is completely dry, tighten the
locknuts by even increments – one after the other –
until all are tightened evenly and the washer-
extractor is fastened securely to the floor.
3. Place the washer-extractor carefully over the
anchor bolts. Never attempt to lift the machine by
the door handle or by pushing on the cover
panels.
10. After installing bolts using a rebar frame, torque
5/8 inch bolts (35 model) to 90 ft. lb. and torque
3/4 inch bolts (60-150 models) to 160 ft. lb.
When using bolts not specified by Alliance
Laundry Systems, refer to the specifications
provided with the bolt.
4. Raise and level the washer-extractor 0.5 inch
(1.27 cm) off the floor on three points, using
spacers such as nut fasteners.
5. Fill the space between the washer-extractor base
and the floor with a good quality non-shrinking
machinery precision grout to ensure a stable
installation. Grout completely under all frame
members. (Remove front panel and back panel to
gain access to all frame members.) Refer to
Figure 13. Force grout under machine base until
all voids are filled.
NOTE: Check and retighten the locknuts after five
to ten days of operation and every month
thereafter.
6. Remove the spacers carefully, allowing the
machine to settle into the wet grout.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
19
Specifications and Dimensions
Mounting Bolt Hole Locations
28.63 in.
(727 mm)
0.75 in.
(19 mm)
43.28 in.
(1089 mm)
40.19 in.
(1022 mm)
34.16 in.
(868 mm)
26.12 in.
(664 mm)
2 in.
2 in.
(51 mm)
(51 mm)
30.12 in.
(765 mm)
UW35PV
FRONT OF MACHINE
N
PHM630N
Figure 8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
34.12 in.
(867 mm)
4.81 in.
(122 mm)
9 in.
(229 mm)
44.81 in.
(1138 mm)
36 in.
(914 mm)
39.25 in.
(997 mm)
10.75 in.
(273 mm)
1.25 in.
(32 mm)
1.25 in.
(32 mm)
34.56 in.
(878 mm)
10.69 in.
(271 mm)
2 in.
(51 mm)
2 in.
(51 mm)
31.63 in.
(803 mm)
0.75 in.
(19 mm)
35.63 in.
(905 mm)
UW60PV
FRONT OF MACHINE
PHM631N
Figure 9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
39.63 in.
(1008 mm)
6.75 in.
(171 mm)
9 in.
(229 mm)
43.75 in.
(1111 mm)
52.19 in.
(1326 mm)
13.63 in.
(346 mm)
2.25 in.
(57 mm)
46.31 in.
(1176 mm)
2.25 in.
(57 mm)
39.75 in.
(1010 mm)
13.63 in.
(346 mm)
35.12 in.
(892 mm)
3 in.
(76 mm)
3 in.
(76 mm)
41.12 in.
(1045 mm)
0.75 in.
(19 mm)
UW80PV / UW100PV
FRONT OF MACHINE
PHM632N
Figure 10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
46.5 in.
(1181 mm)
7 in.
(178 mm)
10 in.
(254 mm)
61.5 in.
(1562 mm)
15 in.
(381 mm)
55.47 in.
48 in.
(1219 mm)
(1409 mm)
48.94 in.
(1243 mm)
15.25 in.
(387 mm)
23.25 in.
(591 mm)
23.25 in.
(591 mm)
48 in.
(1219 mm)
0.75 in.
(19 mm)
UW125PV
FRONT OF MACHINE
PHM633N
Figure 11
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
10.38 in.
(264 mm)
10.38 in.
(264 mm)
67.1 in.
(1704 mm)
57.4 in.
(1457 mm)
12.13 in.
(308 mm)
51.38 in.
(1305 mm)
48.13 in.
(1223 mm)
15 in.
(381 mm)
4 in.
(102 mm)
1.5 in.
(38.1 mm)
1.5 in.
(38.1 mm)
47 in.
(1193 mm)
50 in.
(1270 mm)
UW150PV
FRONT OF MACHINE
PHM634N
Figure 12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
Grout Placement
30.12 in.
(765 mm)
35.63 in.
(905 mm)
17.88 in.
(454 mm)
11.94 in.
(303 mm)
36 in.
(914 mm)
20 in.
(508 mm)
35.94 in.
(913 mm)
4.06 in. typical
(103 mm)
12 in.
(305 mm)
27.5 in.
(699 mm)
4.06 in. typical
(103 mm)
4.06 in. typical
(103 mm)
UW35PV
UW60PV
PHM574N
PHM575N
41.12 in.
(1044 mm)
41.12 in.
(1044 mm)
14 in.
(356 mm)
10.88 in.
(276 mm)
43.75 in.
(1111 mm)
43.81 in.
(1113 mm)
17.5 in.
(445 mm)
20.69 in.
(526 mm)
4.06 in. typical
(103 mm)
33 in.
(838 mm)
33 in.
(838 mm)
4.06 in. typical
(103 mm)
4.06 in. typical
(103 mm)
4.06 in. typical
(103 mm)
PHM192N
PHM576N
UW80PV
UW100PV
50 in.
(1270 mm)
34 in.
(863.6 mm)
56 in.
(1422 mm)
8 in. typical
(203.2 mm)
PHM605N
UW150PV
Figure 13
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
Drain Connection Requirements
1
A drain system of adequate capacity is essential to
washer-extractor performance. Ideally, the water
should empty through a vented pipe directly into a
drain line and drain trough configurations.
2
3
4
1 ft.
(30.48 cm)
5
6
7
PHM621N
1
2
3
4
5
6
7
Rear of Machine
Drain Pipe
1 Inch Minimum Air Gap
Steel Grate
Drain Trough
Strainer
Waste Line
PHM620N
Figure 14
A flexible connection must be made to a vented drain
system to prevent an air lock and to prevent siphoning.
Figure 15
IMPORTANT: Washer-extractor must be installed
in accordance with all local codes and ordinances.
information.
Installation of additional washer-extractors will
IMPORTANT: The top of the vent must be 1 foot
(30.48 cm) lower than the bottom of the inlet valves.
require proportionately larger drain connections. Refer
If proper drain size is not available or practical, a surge
tank is required. A surge tank in conjunction with a
sump pump should be used when gravity drainage is
not possible, such as in below-ground-level
installations.
Before any deviation from specified installation
procedures is attempted, the customer or installer
should contact the distributor.
Increasing the drain hose length, installing elbows, or
causing bends will decrease drain flow rate and
increase drain times, impairing washer-extractor
performance.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
26
Specifications and Dimensions
IMPORTANT: Do not route the overflow vent pipe
to a direct drain system.
For UW125PV and UW150PV Models Only
IMPORTANT: Do not block the overflow vent
above the drain line.
If water or suds flow from the overflow vent and the
machine has been verified to be operating properly
with proper water levels and correct amount of laundry
chemicals, a drain line may be added to the vent and
routed to a drain trough.
1. Remove the riveted bracket on the rear panel for
access to the overflow vent pipe.
2. Route a drain pipe from the vent pipe to a drain
trough. Drain pipe should be routed straight
across or down and be suspended above drain
trough by at least 3 inches (7.62 cm).
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
27
Specifications and Dimensions
Specifications
UWPV Pocket Hardmount
Drain Information
35
60
80
100
125
150
Drain connection size, I.D., in (mm)
With second drain:
2.38 (60)
3 (76)
3 (76)
3 (76)
3 (76)
3 (77)
For Premium Wet Clean option†
3 (76)
1
3 (76)
1
Number of drain outlets
With second drain:
2
2
2
2
For Premium Wet Clean option†
2
2
Drain flow capacity, gal/min (l/min)
35 (132)
64 (242)
120 (454)
9 (255)
120 (454)
11 (311)
140 (530)
13 (368)
140 (530)
13 (368)
For Premium Wet Clean option†
70 (265)
5 (142)
100 (379)
6 (170)
3
Recommended drain pit size, ft (l) ‡
†For wet-clean-capable washer-extractors only.
‡Sized for one machine using overflow level.
Table 3
UWPV Pocket Hardmount
Drain Line Sizing
Minimum Drain I.D., in (mm)
Number of Machines
Model
1
2
3
4
3 (76.2)
3 (76.2)
4 (102)
4 (102)
4 (102)
4 (102)
3 (76.2)
4 (102)
6 (152)
6 (152)
6 (152)
6 (152)
3.5 (88.9)
6 (152)
6 (152)
6 (152)
6 (152)
6 (152)
4 (102)
35
60
6 (152)
8 (203)
8 (203)
8 (203)
8 (203)
80
100
125
150
Table 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
Water Connection
DANGER
To avoid personal injury, recommended
inlet water temperature should be no
higher than 125° Fahrenheit (51° Celsius).
W709
UWPV Pocket Hardmount
Water Supply Information
Specifications
35
60
80/100
2
125/150
2
Number of main fill water inlets
Main fill water inlet size, in (mm)
Number of Spray Rinse water inlets
Spray rinse water inlet size, in (mm)
Recommended pressure psi (bar)
2
2
0.5 (12.7)
2
0.75 (19)
2
0.75 (19)
2
1 (25.4)
2
0.5 (12.7)
0.5 (12.7)
0.75 (19)
0.75 (19)
30 – 85 (2 – 5.7)
Inlet flow capacity (80 psi), gal/min
(l/min)
28 (106)
39 (148)
50 (189)
75 (284)
Table 5
Connections should be supplied by hot and cold water
lines of at least the sizes shown in the Water Supply
Line Sizing table. Installation of additional machines
will require proportionately larger water lines. Refer to
Table 6. Flush the water lines before connecting them
to the machine.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
To connect water service to machine with rubber
hoses, use the following procedure:
UWPV Pocket Hardmount
Water Supply Line Sizing
1. Before installing hoses, flush the water system
for at least two minutes.
Supply Line Size, in (mm)
Number
of Machines
2. Check filters in the washer-extractor’s inlet hoses
for proper fit and cleanliness before connecting.
Main
Hot/Cold
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1 (25)
1.5 (38)
2 (50)
0.75 (19)
1 (25)
3. Hang the hoses in a large loop; do not allow them
to kink.
35
60
If additional hose lengths are needed, use flexible
hoses with screen filters. Each hose should have a
screen filter installed to keep rust and other foreign
particles out of the water inlet valves.
1.25 (32)
1.5 (38)
1 (25)
2 (50)
1.25 (32)
2 (50)
1.25 (32)
1.5 (38)
2 (50)
Pressure of 30 – 85 psi (2 – 5.7 bar) provides best
performance. Although the washer-extractor will
function properly at lower pressures, increased fill
times will occur.
2 (50)
2.5 (64)
1.25 (32)
2 (50)
1 (25)
Suitable air cushions should be installed in supply
1.25 (32)
1.5 (38)
2 (50)
80
2 (50)
For machines labeled with the CE mark, backsiphon
protection devices must be installed previous of all
machine water inlet valves in accordance with
accepted European standards.
2.5 (64)
1.5 (38)
2 (50)
1 (25)
1.5 (38)
1.5 (38)
2 (50)
100
125
150
2 (50)
2.5 (64)
2 (50)
1.25 (32)
2 (50)
1
2.5 (64)
2.5 (64)
2.5 (64)
2 (50)
2 (50)
2.5 (64)
1.25 (32)
2 (50)
2.5 (64)
2.5 (64)
2.5 (64)
2 (50)
2
2.5 (64)
Table 6
P038I
1
2
Air Cushions (Risers)
Water Supply Faucets
Figure 16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
The AC inverter drive requires a clean power supply
free from voltage spikes and surges. A voltage monitor
should be used to check incoming power. The
customer’s local power company may provide such a
monitor.
Electrical Installation Requirements
IMPORTANT: Electrical ratings are subject to
change. Refer to serial decal for electrical ratings
information specific to your machine.
If input voltage measures above 230V for a 200V drive
or above 440V for a 400V drive, ask the power
company to lower the voltage. As an alternative, a
step-down transformer kit is available from the
distributor. Voltages above 250V and 490V require
additional measures. Contact the distributor or the
manufacturer for assistance.
WARNING
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar with
the potential hazards involved. Failure to
observe this warning may result in
personal injury and/or equipment damage,
and may void the warranty.
WARNING
Never touch terminals or components of
the AC inverter drive unless power is
disconnected and the “CHARGE”
SW004
indicator LED is off. The AC inverter drive
retains potentially deadly voltage for some
time after the power is disconnected.
There are no user-serviceable parts inside
the AC inverter drive. Tampering with the
WARNING
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel
familiar with electrical test procedures,
test equipment, and safety precautions
should attempt adjustments and
drive will void the warranty.
SW009
DANGER
troubleshooting. Disconnect power from
the machine before removing the control
box cover, and before attempting any
When controlling the AC inverter drive
with a parameter unit, the machine’s
computer and its safety features are
bypassed. This would allow the basket to
rotate at high speeds with the door open.
When using a parameter unit to control the
AC inverter drive, a large sign should be
placed on the front of the machine
service procedures.
SW005
WARNING
Ensure that a ground wire from a proven
earth ground is connected to the ground
lug near the input power block on this
machine. Without proper grounding,
personal injury from electric shock could
occur and machine malfunctions may be
warning people of the imminent danger.
SW003
evident.
SW008
Electrical connections are made at the rear of the
control module. The machine must be connected to the
proper electrical supply shown on the identification
plate attached to the side of the control module, using
copper conductors only.
IMPORTANT: Alliance Laundry Systems
warranty does not cover compounds that fail as a
result of improper input voltage.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
31
Specifications and Dimensions
The AC drive provides thermal overload protection for
the drive motor. However, a separate three-phase
circuit breaker or electrical supply disconnecting
device must be installed for complete electrical
overload protection. This prevents damage to the
motor by disconnecting all legs if one should be lost
accidentally. Check the data plate on the back of the
requirements.
1
2
Connections to
Control Module
IMPORTANT: Do NOT use fuses in place of a
circuit breaker.
(L1)
R
Black
(L2)
S
Blue
(L3)
T
Red
CAUTION
Do not use a phase adder on any variable-
speed machine.
PHM572N
SW037
1
2
Grounding Lug: Connect to proven earth
ground
Power Input Block
The washer-extractor should be connected to an
individual branch circuit not shared with lighting or
other equipment.
Figure 17
The connection should be shielded in a liquid-tight or
approved flexible conduit with proper conductors of
correct size installed in accordance with the National
Electric Code or other applicable codes. The
connection must be made by a qualified electrician
using the wiring diagram provided with the washer-
extractor, or according to accepted European standards
for equipment labeled with the CE mark.
After electrical installation is complete, run the
machine through a test cycle and check for a clockwise
basket rotation during the extract step. If rotation is not
clockwise, disconnect the power from the machine and
have a qualified electrician reverse any 2 motor leads at
the AC drive terminal block.
50 feet (15.24 meters). Use next larger size for runs of
50 to 100 feet (15.24 to 30.48 meters). Use 2 sizes
larger for runs greater than 100 feet (30.48 meters).
For personal safety and for proper operation, the
washer-extractor must be grounded in accordance with
state and local codes. If such codes are not available,
grounding must conform with the National Electric
Code, article 250 (current edition) or accepted
European standards for equipment labeled with the CE
mark. The ground connection must be made to a
proven earth ground, not to conduit or water pipes.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
32
Specifications and Dimensions
UWPV Pocket Hardmount
Electrical Specifications
Voltage Designation
Standard
Electric Heat
N
P
440 – 480
380 – 415
200 – 240
200 – 240
440 – 480
380 – 415
200 – 240
200 – 240
200 – 240
50/
50/
50/
50/
50/
50/
50/
50/
3
3
3
1
3
3
3
1
3
3
3
2
3
3
3
2
4
4
15
15
15
20
15
15
15
30
20
14
14
14
12
14
14
14
10
12
2.5
2.5
2.5
4
25
22
38
30
30
50
10
10
6
6
6
35
Q
T
N
P
6
16
17
6
Not available in this voltage.
2.5
2.5
2.5
6
33
29
66
40
40
80
8
8
3
10
10
25
6
Q
T
X
12
14
14
60
80
Not available in this voltage.
Not available in this voltage.
50/
60
1 or
3
2 or
3
4 or 4
N
P
440 – 480
380 – 415
200 – 240
440 – 480
380 – 415
200 – 240
440 – 480
380 – 415
200 – 240
440 – 480
380 – 415
200 – 240
50/
50/
50/
50/
50/
50/
50/
50/
50/
50/
50/
50/
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
7
7
15
15
20
15
15
20
15
15
20
15
15
20
14
14
12
14
14
12
14
14
12
14
14
12
2.5
2.5
4
66
57
99
66
57
99
66
57
132
80
70
3
4
25
25
50
25
25
50
25
25
70
Q
N
P
13
7
110
80
1
2.5
2.5
4
3
10
0
7
70
4
Q
N
P
13
7
110
80
1
2.5
2.5
4
3
12
5
7
70
4
Q
N
P
13
8
140
2/0
2.5
2.5
4
NOT
AVAILABLE
15
0
8
Q
14
NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.
Table 7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
For washer-extractors equipped with optional steam
heat, install piping in accordance with approved
commercial steam practices. Steam requirements are
Steam Requirements
(Steam Heat Option Only)
WARNING
NOTE: Failure to install the supplied steam filter
may void the warranty.
Never touch internal or external steam
pipes, connections, or components. These
surfaces can be extremely hot and will
cause severe burns. The steam must be
turned off and the pipe, connections, and
components allowed to cool before the
pipe can be touched.
SW014
UWPV Pocket Hardmount
Steam Supply Information
35
60
80
100
125/150
Steam inlet connection, in
(mm)
1/2 (DN13)
1/2 (DN13)
1
1/2 (DN13)
1/2 (DN13)
3/4 (DN19)
Number of steam inlets
1
1
1
1
Recommended pressure, psi
(bar)
30 – 80
(2.0 – 5.5)
30 – 80
(2.0 – 5.5)
30 – 80
(2.0 – 5.5)
30 – 80
(2.0 – 5.5)
30 – 80
(2.0 – 5.5)
Maximum pressure, psi (bar)
80 (5.5)
80 (5.5)
80 (5.5)
80 (5.5)
80 (5.5)
Table 8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
Undiluted chemical dripping can damage the washer-
extractor. Therefore, all chemical supply dispenser
pumps should be mounted below the washer’s
injection point. All dispenser tubing should also run
below the injection point. Loops do not prevent drips if
these instructions are not followed. Failure to follow
these instructions could damage the machine and void
Injection Supply System.
Chemical Injection Supply System
WARNING
Wear eye and hand protection when
handling chemicals; always avoid direct
contact with raw chemicals. Read the
manufacturer’s directions for accidental
contact before handling chemicals.
Ensure an eye-rinse facility and an
emergency shower are within easy reach.
Check at regular intervals for chemical
leaks.
SW016
2
1
3
PHM585N
1
2
Injection Point
Chemical Dispenser Pump Outlet
3
PVC Pipe
Figure 18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
DESIGN 7 AND LATER
Connecting External Liquid Supplies to the
Washer-Extractor
1
1. Remove knockout from supply dispenser. Refer
tubing ring.
2
3
4
2. Install PG connector in hole with strain reliefs,
included in the seal nut.
5
3. Insert tubes through PG base. Do not remove
cups. Tube should extend into the plastic cup,
with the exception of the softener tube, which
should be routed to the outside of the cup.
6
4. Tighten the seal nut to prevent tubing from
escaping the assembly.
5. Before operating machine, confirm lid is
completely closed.
Do not attempt to make chemical injection electrical
connections to points other than those provided
specifically for that purpose by the factory.
Chemical Injection Supply System
PHM559N
Number of dry supply compartments
Number of liquid supply connections
5
1
2
3
4
5
6
Tubing from Pump
Seal Nut
Tubing Ring
Base
Lid
Nut
5
Liquid supply connection size, in
(mm)
0.63 (15.9)
Figure 19
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
1
2
3
4
5
6
PHM553N
1
2
3
Strain Relief for Liquid Chemical Supply Lines
Supply Dispenser Lid
Nozzles
4
5
6
Dry Supply Cups
Dry Supply Insert
Polypropylene Supply Dispenser
IMPORTANT: Do not attach anything to nozzles. Air gap must be maintained.
Figure 20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
The terminal strip that furnishes the supply output
signal for the chemical injection supply pumps, is
located inside the control module at the rear. Access is
through the rear panel of the module.
Any injection system pump which requires 110VAC
must be powered by a separate external power
source.
Terminals SUPPLY 1 through SUPPLY 9 and
common provide 200 – 240VAC fused at 500mA.
These terminals may be used to provide signals to the
chemical injection system but must not be used to
provide power to the pump. Do not attempt to increase
fuse rating as this may cause damage to the washer-
extractor’s circuitry.
CAUTION
Attempting to obtain 110VAC by using L1
or L2 with the common may damage
laundry machine circuitry and/or the
chemical injection system. Using a
240VAC power wire in the washer-
extractor and an earth ground to obtain
110VAC could cause microprocessor
An external chemical injection system requiring 200 –
240VAC can be powered through LINE 1 and LINE 2
on the external supply terminal strip on UWPVQ, PVT
and PVX models. Any chemical injection system used
with UWPVN and UWPVP models must be powered
by a separate external power source.
problems.
SW028
Consult the chemical injection supply system
instructions for operational details.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
38
Specifications and Dimensions
Designs 1-4
Connecting External Liquid Supplies
to the Washer-Extractor
1
Plugs are assembled inside the tubing ring.
2. Install strain reliefs, included in the seal nut.
2
3. Insert tubes through base. Do not remove cups.
Tube should extend into the plastic cup, with the
exception of the softener tube, which should be
routed to the outside of the cup.
3
4
5
4. Tighten the seal nut to prevent tubing from
escaping the assembly.
5. Before operating machine, confirm lid is
completely closed.
6
Do not attempt to make chemical injection electrical
connections to points other than those provided
specifically for that purpose by the factory.
Chemical Injection Supply System
Number of dry supply compartments
Number of liquid supply connections
5
5
Liquid supply connection size,
in (mm)
0.63 (15.9)
P041I
1
2
3
4
5
6
Tubing from Pump
Seal Nut
Tubing Ring
Base
Lid
Nut
Figure 21
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
1
2
5
3
4
6
DESIGNS 1-4
P048I
1
2
3
Strain Relief for Liquid Chemical Supply Lines
Supply Dispenser Lid
Dry Supply Cups
4
5
6
Dry Supply Insert
Four Way Water Valve
Supply Dispenser
Figure 22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232084
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Dimensions
NOTE: All power must be removed from the
washer-extractor before the Premium Wet Clean
Module installation instructions are executed.
Premium Wet Clean Module
Refer to installation instructions provided with
Premium Wet Clean Module for installation
instructions.
NOTE: Pump motor is prewired for 200 – 240V
input. Motor must be rewired for 380V or greater
input.
WARNING
Lock out the main power panel and lock
out the power supply to the control box
before attempting any service procedures.
SW007
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232084
41
|