NetMaster
Topload Washer
Refer to Page 7 for Model Numbers
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 210140R2
October 2006
www.comlaundry.com
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: The WARNING and IMPORTANT
instructions appearing in this manual are not meant
to cover all possible conditions and situations that
may occur. It must be understood that common
sense, caution, and carefulness are factors which
cannot be built into these washers. These factors
MUST BE supplied by the person(s) installing,
maintaining, or operating the washer.
WARNING
Failure to install, maintain, and/or operate
this machine according to the
manufacturer's instructions may result in
conditions which can produce bodily injury
and/or property damage.
W030
Always contact the distributor, service agent, or the
manufacturer about any problems or conditions you do
not understand.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
210140
1
Notes
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
210140
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Identification ...........................................................................
Preliminary Information....................................................................
About the Control .................................................................................
Glossary of Terms.................................................................................
Power Failure Recovery .......................................................................
Communications...................................................................................
Infra-red Communications (Optional)..................................................
7
9
9
9
9
9
9
Table of
Contents
NetMaster Identification.................................................................... 11
Select Cycle Pads.................................................................................. 11
Select Wash Temp Pads........................................................................ 11
VFD Display Identification................................................................ 13
Light Emitting Diodes (LEDs) ............................................................. 13
Washer Operation .............................................................................. 15
Start Up................................................................................................. 15
Ready Mode.......................................................................................... 15
Cycle Sequence..................................................................................... 15
Opening the Washer Lid....................................................................... 15
Signals................................................................................................... 15
Changing Cycles................................................................................... 15
NetMaster Special Features............................................................... 17
Programming NetMaster ...................................................................... 17
Collecting Audit Information ............................................................... 17
Testing Machine and NetMaster Functions.......................................... 17
Sales Floor Feature ............................................................................... 17
Rapid Advance Feature......................................................................... 17
Clearing the NetMaster Vend Feature .................................................. 17
Communications Mode......................................................................... 17
Coin Drop ............................................................................................. 17
Start Pulse Operation ............................................................................ 18
Service Door and Coin Vault Openings ............................................... 18
Break-In Alarm..................................................................................... 18
Special Vend......................................................................................... 18
Lucky Cycle.......................................................................................... 18
Site Code Pricing.................................................................................. 18
Special Cycle ........................................................................................ 18
Opening the Service Door
(Coin Models Only)............................................................................. 19
Entering the Manual Mode................................................................ 21
How to Enter the Manual Mode ........................................................... 21
Programming NetMaster ................................................................... 23
What Can Be Programmed? ................................................................. 23
Programmable Options Available......................................................... 23
1. Audio Signal “+001” ................................................................... 24
2. Reg. Hot Wash Vend Price “+002” ............................................ 26
3. Reg. Warm Wash Vend Price “+003” ........................................ 28
4. Reg. Cold Wash Vend Price “+004” ........................................... 30
5. Site Code #1 Hot Wash Vend Price “+005” ............................... 32
6. Site Code #1 Warm Wash Vend Price “+006” ........................... 34
7. Site Code #1 Cold Wash Vend Price “+007” ............................. 36
8. Special Cycle Vend Price “+008” ............................................... 38
9. Special Vend A Days Enable “+009” ......................................... 40
10. Special Vend A Start Hour “+010” ............................................. 45
11. Special Vend A Length in Hours “+011” ................................... 46
12. Special Vend A Start Month “+012” .......................................... 47
13. Special Vend A Start Date “+013” ............................................. 48
14. Special Vend A End Month “+014” ........................................... 49
15. Special Vend A End Date “+015” .............................................. 50
© Copyright 2006, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
210140
3
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Special Vend A Site Code #1 “+016” ......................................... 51
17. Special Vend A Reg. Hot Wash Vend Price “+017” .................. 53
18. Special Vend A Reg. Warm Wash Vend Price “+018” .............. 55
19. Special Vend A Reg. Cold Wash Vend Price “+019” ................ 57
20. Special Vend A Auto-Shutdown Enable “+020” ........................ 59
21. Coin #1 Value “+021” ................................................................ 60
22. Coin #2 Value “+022” ................................................................ 62
23. Start Pulse Value “+023” ............................................................ 64
24. Default Cycle/Temperature “+024” ............................................ 66
25. Power Fail Reset “+025” ............................................................ 68
26. Set Real-Time Clock Minutes “+026” ........................................ 70
27. Set Real-Time Clock Hours “+027” ........................................... 71
28. Set Real-Time Clock Day “+028” .............................................. 72
29. Set Real-Time Clock Date “+029” ............................................. 73
30. Set Real-Time Clock Month “+030” .......................................... 74
31. Set Real-Time Clock Year “+031” ............................................. 75
32. Set Real-Time Clock Century “+032” ........................................ 76
33. Normal Wash Agitate Time “+033” ........................................... 77
34. Normal Extra Rinse Agitate Time “+034” .................................. 78
35. Normal Rinse Agitate Time “+035” ........................................... 79
36. Normal Final Spin Time “+036” ................................................. 80
37. Permanent Press Wash Agitate Time “+037” ............................. 81
38. Permanent Press Extra Rinse Agitate Time “+038” ................... 82
39. Permanent Press Rinse Agitate Time “+039” ............................. 83
40. Permanent Press Final Spin Time “+040” .................................. 84
41. Delicate Wash Agitate Time “+041” .......................................... 85
42. Delicate Extra Rinse Agitate Time “+042” ................................ 86
43. Delicate Rinse Agitate Time “+043” .......................................... 87
44. Delicate Final Spin Time “+044” ............................................... 88
45. Warm Rinse Enable/Disable “+045” .......................................... 89
46. Control Configuration Data #1 “+046” ....................................... 90
47. Control Configuration Data #3 “+047” ....................................... 94
48. Lucky Option “+048” ................................................................. 96
49. Special Cycle Option “+049” ...................................................... 97
50. Special Cycle Extra Wash Time “+050” .................................... 99
51. Special Cycle Extra Extra-Rinse Time “+051” .......................... 100
52. Smart Card Maximum Value “+052” ......................................... 101
53. Site Code #1 “+053” ................................................................... 103
54. Error Code Programming Parameter “+054” .............................. 105
55. Start Pulse Mode “+055” ............................................................ 107
Collecting Audit Information ............................................................ 109
Manual Reset....................................................................................... 111
Testing Machine and
Electronic Control Functions............................................................. 113
Diagnostic Test Descriptions................................................................ 114
Error Codes......................................................................................... 117
Sales Floor Feature............................................................................. 121
Rapid Advance Feature...................................................................... 123
Clear Vend Feature ............................................................................ 125
Power Fail Recovery........................................................................... 127
Power Fail Reset Disabled.................................................................... 127
Power Fail Reset Enabled..................................................................... 127
Communications Mode ...................................................................... 129
Infra-red Communications.................................................................... 129
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
210140
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Card Reader Communications
(Card Models Only)............................................................................ 129
Network Communications.................................................................... 129
Default Washer Settings..................................................................... 131
Default Settings .................................................................................... 131
Default Cycle........................................................................................ 131
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
210140
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
210140
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Identification
Information in this manual is applicable to these washer
models:
HWTB21
HWTF21
NWTF21
SWLB20
SWLB21
SWLF20
SWLF21
SWTA21
SWTBA0
SWTBA1
SWTB20
SWTB21
SWTC20
SWTC21
SWTF20
SWTF21
SWTH20
SWTH21
SWTJ21
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Preliminary Information
move to the Rinse Spin cycle and prompt the user to
press the START pad. Once the START pad is
pressed, the control will spin out the cycle.
About the Control
NetMaster on the commercial washer is an advanced,
programmable computer that lets the owner control
most machine features by pressing a sequence of
SELECT CYCLE and SELECT WASH TEMP pads.
Communications
NetMaster may be programmed manually, by the
Micro-Wand IIIE™, by the Network, or by a Smart
Card.
NetMaster allows the owner to program custom
cycles, set vend prices, retrieve audit information,
program and run diagnostic cycles, and program
special vend features. Washers shipped from the
factory have a default cycle and wash temperature
setting of PERM PRESS, WARM built in. However,
the owner can change the default cycle, or any cycle,
as needs permit.
Infra-red Communications
(Optional)
The Micro-Wand allows the owner to program and
retrieve information from NetMaster without touching
the keypad. The Micro-Wand greatly expands the
programming options available to the owner. However,
the Micro-Wand is not required to program and operate
the washer. The operation of the Micro-Wand and the
advanced features available are covered separately in
IMPORTANT: In the event of a power failure,
NetMaster will not have to be reprogrammed. It is
designed with a memory system that will remember
how it was programmed (for a minimum of six
years) until the electrical power is restored.
™
the Micro-Wand IIIE instruction manual.
Smart Card Reader Communications
(Card Models Only)
IMPORTANT: It is extremely important that the
washer has a positive ground and that all mechanical
and electrical connections to NetMaster are made
before applying power to or operating the washer.
The control will accept communication with a Card
Reader in order to perform vending transactions when
a card is inserted to pay for cycles. The card reader can
also allow the owner to program and collect audit
information.
Glossary of Terms
The following are a few terms and abbreviations to
learn. These are referred to throughout the instructions.
For detailed information on Smart Card Reader
Communications, refer to the Smart Card Setup
Module in the NetMaster Smart Card Suite software
package.
VFD - Vacuum Fluorescent Display.
This term refers to the window area of the
control that displays words and values.
Network Communications
LED - Light Emitting Diode.
This term refers to the lights on the keypads
and status words of the control.
The control will also accept communication with a
Network Interface Board which allows the control to
be linked to a personal computer. This network link
allows an owner to program, collect data and run
diagnostics on any machine.
Power Failure Recovery
If a cycle is in progress and the power fails, the cycle
status is saved in memory for a minimum of six years
without power. When the power recovers, the washer
will resume into the previously active cycle if so
programmed by the owner.
For detailed information on Network Communications,
refer to the Network instruction manual.
The owner may program a special feature called
POWER FAIL RESET which sets a maximum power
failure duration. To program this feature, refer to
Programming NetMaster, option 25.
If the length of the power failure is greater than the
POWER FAIL RESET time, the control will end the
cycle and the display will revert back to the ready
mode. If the washtub is full of water, the control will
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
10
Download from Www.Somanuals.com. All Manuals Search And Download.
NetMaster Identification
Select Cycle Pads
Select Wash Temp Pads
SELECT CYCLE pads are used to select the specific
washer cycle. These pads include NORMAL, PERM
PRESS, and DELICATES. These pads allow the user
to select a cycle other than the default cycle (PERM
PRESS). The SELECT CYCLE keypads are not active
after the first fill cycle of the washer. The selected
cycle is indicated by the light (LED) on the pad.
Pressing the START pad will confirm the selection
and the cycle will begin. When the Smart Card is used,
the START pad flashes. Pressing the START pad will
start the cycle and deduct the vend price from the card.
SELECT WASH TEMP pads are used to select the
temperature of the water used for the wash fill. These
pads include HOT, WARM, and COLD. These pads
allow the user to select a water temperature other than
the default setting (WARM). The SELECT WASH
TEMP pads are active only during the first fill cycle of
the washer. The selected temperature is indicated by
the light (LED) on the pad.
Both the SELECT WASH TEMP pads and the SELECT
CYCLE pads are used in various combinations for
programming cycles, retrieving audit information,
running diagnostic tests, and other hidden operations.
These instructions cover the manual programming and
data retrieval options.
Electronic Display Control
3
2
4
5
6
1
7
C832I
1
2
3
4
5
6
7
LED Light
SELECT CYCLE pads (top row)
Four 7-Segment Digits
VFD Display
LED Status Lights
START pad
SELECT WASH TEMP pads (bottom row)
Figure 1
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
12
Download from Www.Somanuals.com. All Manuals Search And Download.
VFD Display Identification
INSERT COINS/CARD LED
Light Emitting Diodes (LEDs)
INSERT COINS/CARD LED prompts the user for
coins or a card to satisfy the vend price. Four digits
and decimal point show the vend price remaining to be
satisfied. The vend price displayed will decrease with
each coin inserted. If a new wash temp is selected
during the first fill of the wash cycle and it requires
additional vend, the INSERT COINS/CARD light will
flash one (1) second on and one (1) second off, and the
display will show the vend price remaining to be
satisfied.
LIGHT EMITTING DIODES (LEDs) are used to
indicate the chosen cycle, wash temperature and cycle
status. See below for information on each LED.
CYCLE LED (NORMAL, PERM PRESS or
DELICATES)
CYCLE LED will remain lit the entire cycle.
WASH TEMP LED (HOT, WARM or COLD)
REMOVE CARD LED (Card Models Only)
WASH TEMP LED will remain on until the end of the
cycle or will change to a rinse temperature if programmed
to do so.
REMOVE CARD LED flashes one second on and one
second off after the START pad has been pressed and
the vend has been deducted from the card. It will also
flash when a card is inserted and no vend amount is
required.
WASH LED
WASH LED is lit at the beginning of a Wash cycle and
will remain lit until the wash cycle is complete.
Four 7-Segment Digits
RINSE LED
The 7-SEGMENT DIGITS are used to display the
time remaining in a cycle, vend price, error messages
and descriptive codes. When displaying the time
remaining the colon will flash, and when displaying
the vend price the decimal point may be lit. During
diagnostic testing or manual programming of the
control, these digits will display descriptive codes and
values (as described in Entering the Manual Mode).
RINSE LED is lit at the beginning of the Rinse or
Extra Rinse cycle and will remain lit until the cycle is
complete.
SPIN LED
SPIN LED is lit for all Spin cycles.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer Operation
coin entered after the first fill cycle will be added to
Start Up
the total coin counter, but the user will not be able to
change cycles or water temperature.
When power is applied to the washer, the control will
display INSERT COINS/CARD, the decimal point, and
the vend price. The INSERT COINS/CARD light will
remain lit until the vend price has been satisfied. The
default cycle setting is PERM PRESS, the default
wash water fill temperature is WARM, and the default
rinse water temperature is COLD. The LEDs will be lit
on PERM PRESS and WARM at the start of the cycle.
programmable. Refer to Programming NetMaster.
Opening the Washer Lid
If the washer lid is opened anytime except the last three
minutes of a cycle, the VFD will display “LId” and the
timer will stop. Once the lid is closed, the cycle will
restart from the point of interruption. If the lid is opened
in the final three minutes of the final spin cycle, the timer
will continue to count down to the end of the cycle.
The cycle operation will stop and the VFD will display
“LId”. When the timer reaches 0 minutes, the control
Ready Mode
Signals
There are four options when a signal can be used during
the washer operation. These four options are listed below:
1. End of Cycle Signal
By default, this signal is turned off. If turned on, the
signal sounds for three (3) seconds at the end of a
cycle.
2. Signal On Keypad Depression
By default, this signal is turned on and sounds for
a quarter of a second each time a keypad is pressed.
3. Signal On Coin Drop/Card Insertion
By default, this signal is turned on and will sound
for a quarter of a second each time a coin or card
is entered.
C833I
Figure 2
To start the cycle, the user must press the START
keypad.
4. Signal for Card Removal (Card Models Only)
By default, this signal is turned on and will sound
one second on and one second off when the
REMOVE CARD LED is flashing.
The user will be able to select a different cycle or wash
water temperature by pressing a cycle pad when the
machine is in the ready mode or in the first fill cycle. If
not enough vend is entered to satisfy the vend price, the
control will display the remaining vend price needed to
start the cycle. If the first fill was interrupted to change
the temperature (which requires more money), and the
vend price is not satisfied within 1 minute, the washer
control will go back to the first selection and the cycle
will restart. After the first fill, all key presses will be
ignored, allowing the washer to go through the
complete cycle.
NOTE: Refer to Programming NetMaster to
program signal options.
Changing Cycles
Cycles and wash temperatures can be changed anytime
during the first fill cycle. After the first fill cycle, all
key presses are ignored.
Selecting a higher priced wash temperature will stop the
first fill cycle, and INSERT COINS/CARD will flash one
(1) second on and one (1) second off until the vend price
has been satisfied. After the vend price has been satisfied,
the cycle will restart with the new wash temperature. If
the vend price is not satisfied within 1 minute, the washer
control will go back to the previously set wash
temperature.
When a cycle is complete, the control will display “:00”
until the lid is opened, a key is pressed, or a coin/card is
entered. When one of these three options occur, the display
Cycle Sequence
Upon the start of a cycle, NetMaster will display the
total cycle time. The appropriate LEDs will light while
the machine passes through different cycle steps. Any
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
16
Download from Www.Somanuals.com. All Manuals Search And Download.
NetMaster Special Features
Programming NetMaster
Sales Floor Feature
NetMaster allows the washer owner to program the
control with the use of the keypad. Audit, diagnostic,
cycle and vend information may be programmed and
retrieved by pressing combinations of the Select Cycle
and Select Wash Temp pads.
NetMaster washer has a built-in sales floor routine
used to display all LED lights and the four digits with
the colon and decimal point. This function is designed
to show potential customers the high-tech features of
NetMaster and to verify that all segments of the VFD
work.
For details on programming cycle and vend information,
refer to Programming NetMaster.
For detailed information on using the Sales Floor
feature, refer to Sales Floor Feature.
Collecting Audit Information
Rapid Advance Feature
The control will store audit information in its memory
that can be retrieved by pressing various combinations
of Select Cycle and Select Wash Temp pads. NetMaster
will record coins entered, total wash cycles, and total
start pulses.
This feature allows the user to quickly advance
through active cycles or advance into a cycle from the
ready mode. This feature is useful when tests must be
performed immediately on a washer currently in an
active cycle. In this case, the user can quickly advance
through the cycles to the ready mode. At this point, the
user can perform the required tests and then return the
washer to the point it was interrupted.
For more information on the audit features, refer to
Collecting Audit Information.
NOTE: Additional audit information is retrievable
with the Micro-Wand IIIE, the Card Reader or the
Network. Refer to the appropriate instruction
manual.
For detailed information on using the Rapid Advance
feature, refer to Rapid Advance Feature.
Clearing the NetMaster Vend Feature
Testing Machine and NetMaster
Functions
This feature allows the user to return NetMaster back
to the ready mode if coins have been entered but the
full vend price has not yet been satisfied. Refer to
Special programmable diagnostic features built into
NetMaster allow the owner to run specific diagnostic
tests. By opening and closing the service door and then
pressing various sequences of Select Cycle and Select
Wash Temp pads, the owner may perform the
following tests:
For more information on using the Clear Vend feature,
refer to Clear Vend Feature.
Communications Mode
●
●
●
●
●
●
●
●
●
●
●
Control Software Version Number
Service Door Opening Test
Coin Vault Opening Test
Coin Drop #1 Input Test
Coin Drop #2 Input Test
Lid Switch Input Test
Pressure Switch Opening Test
Show Fill Time Test
Show Drain Time Test
This feature allows the washer control to communicate
with the Micro-Wand IIIE, the Card Reader or the
Network. This allows the washer control to be
programmed and have its data read without using the
keypad.
For more detailed information on using the
Communications Mode feature, refer to
Communications Mode.
Start Pulse Test
Configuration Display Tests
Coin Drop
For detailed information on running diagnostic tests,
refer to Testing Machine and NetMaster Functions.
The control will accept pulses from a single or dual
coin drop to satisfy vend price. Each coin drop will
have the ability to start or run a cycle.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
17
NetMaster Special Features
Start Pulse Operation
Lucky Cycle
The control will accept pulses from a central card
reader system. The machine can be programmed to
receive a single start pulse or multiple start pulses, or
the Start Pulse Option can be turned off. The Start
Pulse Mode allows the machine to go from the
“Ready” mode to the “START” mode after single or
multiple pulses are received.
This feature allows the owner to program the machine
to provide a free vend cycle to customers after a
certain number of cycles have occurred.
For details on programming the Lucky Cycle Option,
refer to Programming NetMaster.
Site Code Pricing
Service Door and Coin Vault
Openings
This feature allows owners to program the control to
accept site codes for special vending that are specific
to select groups or individuals when using cards.
The control will capture the times and dates of the
openings of the Coin Vault and the Service Door. The
information is saved in memory. An open service door
combined with various keypad presses allows the
control to enter manual modes of operation if the
Break-In Alarm is not on. These modes include Manual
Programming, Audit Collection and Diagnostics.
For details on programming the site code options, refer
to Programming NetMaster.
Special Cycle
This feature allows the owner to offer extra features to
customers for an added vend price. Features available
include extra wash time, extra rinse time, and a warm
rinse temperature.
Break-In Alarm
This feature allows the owner to program the machine
to signal a network alarm if the service door or coin
vault is opened without disabling the alarm first. To
avoid the alarm during coin collections, the alarm
must be disabled.
For details on programming the Special Cycle option,
refer to Programming NetMaster.
Special Vend
This feature allows the owner to program the control
to allow programmable vend prices for specific hours
and dates.
For details on programming Special Vend, refer to
Programming NetMaster.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Opening the Service Door
(Coin Models Only)
Manually programming NetMaster requires the user to
NOTE: For card models, the manual programming
option is accessed by disconnecting and reconnecting
a plug behind the control panel, or by inserting the
appropriate card into the card reader.
open and close the service door. Opening and closing
the service door trips a switch allowing access to
various programming options, diagnostics and audit
capabilities.
The service door is located on the top of the meter case.
WARNING
Any disassembly requiring the use of tools
must be performed by a suitably qualified
service person.
W299
SERVICE DOOR
W521IE1A
Figure 3
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering the Manual Mode
For programming, testing, and retrieving information
from NetMaster, it is often necessary to enter the
Manual Mode by following the four simple steps below.
Manual Mode is broken into two groups: Manual
Programming and Manual Rapid Advance/Diagnostics.
Manual Programming can only be turned on or off
with the Micro-Wand IIIE, the Smart Card Reader or
the Network. Refer to the appropriate instruction
manual. Manual Rapid Advance/Diagnostics can be
turned on and off using the Micro-Wand IIIE, by
How to Enter the Manual Mode
1. Be sure the washer is in the ready mode before
washer is in an active cycle, rapid advance
through the cycle. Refer to Rapid Advance
Feature. If coins or a card has been entered, refer
to Clear Vend Feature.
Programming NetMaster), with the Smart Card
Reader, or with the Network.
By default, both groups are turned “ON”.
The manual features available in each group are as
follows (the menu displayed on the VFD in this mode
is in parenthesis).
2. Open the service door. Refer to Opening the
Service Door.
3. While pressing and holding the NORMAL
keypad with one hand, press the HOT keypad
with the other hand.
Manual Programming
Manual Programming (PrOg)
Manual Read Audit (AudT)
Manual Reset (rSET)
4. The VFD display will show “rAPd”. Refer to
Rapid Advance/Diagnostics
Rapid Advance (rAPd)
Show Mode (SHOW)
Diagnostic Tests (dIAg)
If a group is turned “OFF”, the feature menu will still
appear, but the features in the group cannot be entered.
C834I
Figure 4
5. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the options until the
desired option appears in the VFD.
6. Press the START (enter) keypad.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
What Can Be Programmed?
OPTION
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
DESCRIPTION
Special Vend A Reg. Cold Wash Vend Price
Special Vend A Auto-Shutdown Enable
Coin #1 Value
This feature allows the owner to program cycle
parameters, standard vend pricing, special vends and other
features by using the keypads. The control must have
the Manual Programming Mode enabled, which is the
factory default. This mode can only be turned OFF and
ON by using the Micro-Wand IIIE, the Smart Card
Reader or the Network. Refer to this section when
programming NetMaster.
Coin #2 Value
Start Pulse Value
Default Cycle/Temperature
Power Fail Reset
This section offers a detailed description of all 55 options
available to program.
Set Real-Time Clock Minutes
Set Real-Time Clock Hours
Set Real-Time Clock Day
Set Real-Time Clock Date
Set Real-Time Clock Month
Set Real-Time Clock Year
Set Real-Time Clock Century
Normal Wash Agitate Time
Normal Extra Rinse Agitate Time
Normal Rinse Agitate Time
Normal Final Spin Time
Each description includes instructions on when and
why the option might be used and, more importantly,
how to program the option.
For more advanced users, a quick reference list of the
options available through the programming mode is
located on this page.
NOTE: The three numbers in the Option column of
the Programmable Options list are what will be
shown in the VFD display when that option is
selected.
Programmable Options Available
Perm Press Wash Agitate Time
Perm Press Extra Rinse Agitate Time
Perm Press Rinse Agitate Time
Perm Press Final Spin Time
Delicate Wash Agitate Time
Delicate Extra Rinse Agitate Time
Delicate Rinse Agitate Time
Delicate Final Spin Time
Warm Rinse Enable/Disable
Control Configuration Data #1
Control Configuration Data #3
Lucky Option
OPTION
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
DESCRIPTION
Audio Signal
Reg. Hot Wash Vend Price
Reg. Warm Wash Vend Price
Reg. Cold Wash Vend Price
Site Code #1 Reg. Hot Wash Vend Price
Site Code #1 Reg. Warm Wash Vend Price
Site Code #1 Reg. Cold Wash Vend Price
Special Cycle Vend Price
Special Vend A Days Enable
Special Vend A Start Hour
Special Cycle Option
Special Vend A Length in Hours
Special Vend A Start Month
Special Cycle Extra Wash Time
Special Cycle Extra Extra-Rinse Time
Smart Card Maximum Value
Site Code #1
Special Vend A Start Date
Special Vend A End Month
Special Vend A End Date
Error Code Programming Parameter
Start Pulse Mode
Special Vend A Site Code #1
Special Vend A Reg. Hot Wash Vend Price
Special Vend A Reg. Warm Wash Vend Price
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
4. Locate the desired number in the first column of
1. Audio Signal “+001”
Table 1 on the following page.
This option allows the owner to program when the
signal will sound.
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
There are four occasions when a signal may sound
during the washer operation. These four occasions are
listed below:
1
1. End of Cycle Signal
By default, the signal is turned off. If turned on,
the signal will sound for three seconds at the end
of a cycle.
2. Keypad Depression Signal
By default, this signal is turned on and will sound
for a quarter of a second. This signal will sound
each time a keypad is pressed.
3. Coin Input/Card Insertion Signal
By default, this signal is turned on and will sound
for a quarter of a second each time a coin or card
is entered.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
4. Remove Card Signal (Card Models Only)
By default, this signal is turned on and will sound
one second on and one second off when the
REMOVE CARD LED is flashing.
3
Press this pad (-) to scroll back or decrease a value
Figure 7
How to Program the Audio Signal
For Example: A user might wish to have the signal
sound only when a keypad is pressed. Entering the
number “1” in step 5 would turn off all the options
except KEYPAD. In this instance, the signal would
sound only when a keypad is pressed.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad.
6. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+002”, will appear in the VFD.
NOTE: To program “+002” (Reg. Hot Wash Vend
refer to the appropriate section.
C762I
Figure 5
3. “+001” will appear in the VFD. Press the
START (enter) keypad. A number will appear in
the VFD. This number corresponds to the current
Audio Signal Programming Value.
C821I
Figure 6
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Programming NetMaster
How to Exit Programming Feature
Signal Remove Coin/Card End of
Key
Value
Card
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
Input
OFF
OFF
OFF
OFF
ON
Cycle
OFF
OFF
ON
Pressed
1. Be sure the control shows a programmable
option, not a value.
0
OFF
ON
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
1
2
OFF
ON
3
ON
How to Read Table 1
4
OFF
OFF
ON
OFF
ON
To determine the correct number required to program
the Audio Signal, use the following chart. The Signal
Value column contains the number required in step 5.
The other columns correspond to individual options.
5
ON
6
ON
OFF
ON
7
ON
ON
Each column of options contains a unique combination
of the words “ON” and “OFF” that indicates if that
column’s option is turned on or off when the Signal
Value is entered. Select the desired combination of
options and enter the number found in the Signal
Value column.
8
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
9
ON
10
11
12
13
14
15
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
Table 1
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
4. When “+002” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Reg. Hot Wash Vend Price. The fifth digit
will appear in the VFD and will flash one second
2. Reg. Hot Wash Vend Price
“+002”
This option allows the owner to set the vend price for a
hot wash. This vend price will be displayed in the
VFD when HOT is selected.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
How to Program the Reg. Hot Wash
Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 10
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
NOTE: The vend price can be set from 1 to 65,535.
C762I
Figure 8
1
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+002” appears in the VFD. Refer
3
2
C860I
C764I
C764I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 9
3
Press this pad (-) to scroll back or decrease a value
Figure 11
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 12
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+003”, will
appear in the VFD.
NOTE: To program “+003” (Reg. Warm Wash
options, refer to the appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Programming NetMaster
4. When “+003” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Reg. Warm Wash Vend Price. The fifth digit
will appear in the VFD and will flash one second
3. Reg. Warm Wash Vend Price
“+003”
This option allows the owner to set the vend price for a
warm wash. This vend price will be displayed in the
VFD when WARM is selected.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
How to Program the Reg. Warm Wash
Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 15
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
NOTE: The vend price can be set from 1 to 65,535.
C762I
Figure 13
1
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+003” appears in the VFD. Refer
3
2
C860I
C765I
C765I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 14
3
Press this pad (-) to scroll back or decrease a value
Figure 16
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 17
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+004”, will appear
in the VFD.
NOTE: To program “+004” (Reg. Cold Wash
options, refer to the appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Programming NetMaster
4. When “+004” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Reg. Cold Wash Vend Price. The fifth digit
will appear in the VFD and will flash one second
4. Reg. Cold Wash Vend Price
“+004”
This option allows the owner to set the vend price for a
cold wash. This vend price will be displayed in the
VFD when COLD is selected.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
How to Program the Reg. Cold Wash
Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 20
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
NOTE: The vend price can be set from 1 to 65,535.
C762I
Figure 18
1
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+004” appears in the VFD. Refer
3
2
C860I
C766I
C766I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 19
3
Press this pad (-) to scroll back or decrease a value
Figure 21
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 22
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+005”, will appear
in the VFD.
NOTE: To program “+005” (Site Code #1 Reg. Hot
other options, refer to the appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Programming NetMaster
4. When “+005” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Site Code #1 Hot Wash Vend Price. The fifth
digit will appear in the VFD and will flash one
5. Site Code #1 Hot Wash Vend
Price “+005”
This option allows the owner to set the vend price for a
hot wash when cards with a special site code are used
by specific groups or individuals.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
How to Program the Site Code #1 Hot
Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 25
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
NOTE: The vend price can be set from 0 to 65,535.
C762I
Figure 23
1
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+005” appears in the VFD. Refer
3
2
C860I
C835I
C835I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 24
3
Press this pad (-) to scroll back or decrease a value
Figure 26
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 27
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+006”, will
appear in the VFD.
NOTE: To program “+006” (Site Code #1 Warm
other options, refer to the appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Programming NetMaster
4. When “+006” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Site Code #1 Warm Wash Vend Price. The
fifth digit will appear in the VFD and will flash
6. Site Code #1 Warm Wash Vend
Price “+006”
This option allows the owner to set the vend price for a
warm wash when cards with a special site code are
used by specific groups or individuals.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
How to Program the Site Code #1 Warm
Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 30
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
NOTE: The vend price can be set from 0 to 65,535.
C762I
Figure 28
1
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+006” appears in the VFD. Refer
3
2
C860I
C836I
C836I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 29
3
Press this pad (-) to scroll back or decrease a value
Figure 31
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 32
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+007”, will
appear in the VFD.
NOTE: To program “+007” (Site Code #1 Cold
other options, refer to the appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Programming NetMaster
4. When “+007” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Site Code #1 Cold Wash Vend Price. The
fifth digit will appear in the VFD and will flash
one second on, one second off. Refer to Figure
35.
7. Site Code #1 Cold Wash Vend
Price “+007”
This option allows the owner to set the vend price for a
cold wash when cards with a special site code are used
by specific groups or individuals.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
How to Program the Site Code #1 Cold
Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 35
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
C762I
NOTE: The vend price can be set from 0 to 65,535.
Figure 33
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+007” appears in the VFD. Refer
1
3
2
C837I
C837I
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 34
3
Press this pad (-) to scroll back or decrease a value
Figure 36
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 37
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+008”, will appear
in the VFD.
NOTE: To program “+008” (Special Cycle Vend
refer to the appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Programming NetMaster
4. When “+008” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Special Cycle Vend Price. The fifth digit will
appear in the VFD and will flash one second on,
8. Special Cycle Vend Price
“+008”
This option allows the owner to program the machines
to offer extra features to the customers for an added
vend price. This vend price will be displayed in the
VFD for 30 seconds starting 5 seconds after the start
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
How to Program Special Cycle Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
Figure 40
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
NOTE: The vend price can be set from 1 to 65,535.
1
C762I
Figure 38
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+008” appears in the VFD. Refer
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C770I
C770I
Figure 41
6. Press the START (enter) keypad to enter the fifth
digit and display the remaining four digits. The
active digit will flash one second on and one
Figure 39
C827I
Figure 42
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Programming NetMaster
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
8. Press the START (enter) keypad with the last
active digit. The next option, “+009”, will appear
in the VFD.
NOTE: To program “+009” (Special Vend A Days
options, refer to the appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Programming NetMaster
4. When “+009” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD that corresponds to the current Special
Vend A Days Enable Programming Value.
9. Special Vend A Days Enable
“+009”
This option allows the owner to set the day or days of
a special vend.
5. Locate the desired number in the first column of
Table 2 on the following pages.
Special Vend A is used to change the standard vend
prices for special occasions or to turn the machine off.
The special vend can be programmed to start and end
on a specific day or days of the week.
6. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
The owner may also turn the Special Vend A option
on or off if desired.
1
How to Program Special Vend A Days
Enable
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 45
C762I
7. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+010”, will appear in the VFD.
Figure 43
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+009” appears in the VFD. Refer
NOTE: To program “+010” (Special Vend A Start
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C771I
C771I
Figure 44
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Programming NetMaster
How to Read Table 2
To determine the correct number required to program
the Special Vend A Days Enable, use the following
table. The “SPA” Value column contains the number
required in step 6. The other columns correspond to
individual days.
Each column of days contains a unique combination of
the words “ON” and “OFF” that indicates if that
column’s day is turned on or off when the “SPA”
value is entered. Select the desired combination of
days and enter the number found in the “SPA” value
column.
“+009”
WED
“SPA” VALUE
SAT
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FRI
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
THUR
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
TUE
OFF
OFF
OFF
OFF
ON
MON
OFF
OFF
ON
SUN
OFF
ON
ON/OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
3
5
OFF
ON
7
ON
9
OFF
OFF
ON
OFF
ON
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
OFF
Table 2
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
“+009” (continued)
“SPA” VALUE
71
SAT
FRI
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
THUR
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
WED
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
TUE
OFF
ON
ON
ON
MON
ON
OFF
OFF
ON
SUN
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON/OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
73
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
151
153
155
157
159
161
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
Table 2
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
“+009” (continued)
“SPA” VALUE
163
165
167
169
171
173
175
177
179
181
183
185
187
189
191
193
195
197
199
201
203
205
207
209
211
213
215
217
219
221
223
225
227
229
231
233
235
237
239
241
243
245
247
249
251
253
SAT
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
FRI
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
THUR
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
WED
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
TUE
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
MON
OFF
ON
SUN
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON/OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
Table 2
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
“+009” (continued)
“SPA” VALUE
SAT
ON
FRI
ON
THUR
ON
WED
ON
TUE
ON
MON
ON
SUN
ON
ON/OFF
255
ON
Table 2
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the start hour to
10. Special Vend A Start Hour
“+010”
This option allows the owner to set the hour that
Special Vend A will begin.
1
How to Program Special Vend A Hour
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 48
Figure 46
6. Press the START (enter) keypad when the
correct hour appears in the VFD. The next option,
“+011”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+010” appears in the VFD. Refer
NOTE: To program “+011” (Special Vend A
other options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C772I
Figure 47
4. When “+010” appears in the VFD, press the
START (enter) keypad. The current start time (in
military time) will appear in the VFD.
NOTE: The hours will be displayed in military
time.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current length
of hours to the desired number of hours. Refer to
11. Special Vend A Length in Hours
“+011”
This option allows the owner to set the length in hours
for Special Vend A.
1
How to Program Special Vend A Length
in Hours
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 51
Figure 49
6. Press the START (enter) keypad when the
correct hour appears in the VFD. The next option,
“+012”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+011” appears in the VFD. Refer
NOTE: To program “+012” (Special Vend A Start
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
77I
C773I
Figure 50
4. When “+011” appears in the VFD, press the
START (enter) keypad. The current length in
hours will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the start month to
12. Special Vend A Start Month
“+012”
This option allows the owner to set the month that
Special Vend A will begin.
If “0” is selected and Special Vend A is on,
Special Vend A will occur at the time and days of
week selected, regardless of the month.
NOTE: If Special Vend A Start Month, Start Date,
End Month, or End Date are programmed to zero
(default is zero), the special Vend A will be active
1
How to Program Special Vend A Start
Month
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 54
6. Press the START (enter) keypad when the
correct month appears in the VFD. The next
option, “+013”, will appear in the VFD.
C762I
Figure 52
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+012” appears in the VFD. Refer
NOTE: To program “+013” (Special Vend A Start
refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
1. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C774I
Figure 53
4. When “+012” appears in the VFD, press the
START (enter) keypad. The current start month
will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the start date to
13. Special Vend A Start Date
“+013”
This option allows the owner to set the date that
Special Vend A will begin.
If “0” is selected and Special Vend A is on,
Special Vend A will occur at the time or days of
week selected, regardless of the date.
How to Program Special Vend A Start
Date
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 55
Figure 57
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+013” appears in the VFD. Refer
6. Press the START (enter) keypad when the
correct date appears in the VFD. The next option,
“+014”, will appear in the VFD.
NOTE: To program “+014” (Special Vend A End
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C775I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 56
4. When “+013” appears in the VFD, press the
START (enter) keypad. The current start date
will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
48
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the end month to
14. Special Vend A End Month
“+014”
This option allows the owner to set the month that
Special Vend A will end.
If “0” is selected and Special Vend A is on,
Special Vend A will occur at the time or day of
week selected, regardless of the month.
How to Program Special Vend A End
Month
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 58
Figure 60
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+014” appears in the VFD. Refer
6. Press the START (enter) keypad when the
correct month appears in the VFD. The next
option, “+015”, will appear in the VFD.
NOTE: To program “+015” (Special Vend A End
refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C776I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 59
4. When “+014” appears in the VFD, press the
START (enter) keypad. The current end month
will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the end date to the
15. Special Vend A End Date “+015”
This option allows the owner to set the date that
Special Vend A will end.
If “0” is selected and Special Vend A is on,
Special Vend A will occur at the time or days of
week selected, regardless of the date.
How to Program Special Vend A End Date
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
1
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
C762I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 61
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+015” appears in the VFD. Refer
3
Press this pad (-) to scroll back or decrease a value
Figure 63
6. Press the START (enter) keypad when the
correct date appears in the VFD. The next option,
“+016”, will appear in the VFD.
NOTE: To program “+016” (Special Vend A Site
options, refer to the appropriate section.
How to Exit Programming Feature
C777I
1. Be sure the control shows a programmable option,
not a value.
Figure 62
4. When “+015” appears in the VFD, press the
START (enter) keypad. The current end date will
appear in the VFD.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
50
Programming NetMaster
4. When “+016” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Special Vend A Site Code #1. The fifth digit
will appear in the VFD and will flash one second
16. Special Vend A Site Code #1
“+016”
This option allows the owner to program the machines
to accept site codes for Special Vend A that are
specific to select groups or individuals when using
cards. It also allows the owner to only give Special
Vend A pricing for a card with this site code. If
Special Vend A site code is zero, then Special Vend A
pricing will apply to all cards.
NOTE: If the Special Vend A Site Code #1 price is
10000 or more, the fifth digit is “1”. If the Special
Vend A Site Code #1 price is 9999 or less, the fifth
digit is “0”.
How to Program the Special Vend A Site
Code #1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 66
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
NOTE: The coin value can be set from 1 to 65,535.
1
C762I
Figure 64
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+016” appears in the VFD. Refer
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C838I
C838I
3
Press this pad (-) to scroll back or decrease a value
Figure 65
Figure 67
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 68
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+017”, will appear
in the VFD.
NOTE: To program “+017” (Special Vend A Reg.
program other options, refer to the appropriate
section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
52
Programming NetMaster
4. When “+017” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Special Vend A Reg. Hot Wash Vend Price.
The fifth digit will appear in the VFD and will
flash one second on and one second off. Refer to
17. Special Vend A Reg. Hot Wash
Vend Price “+017”
This option allows the owner to set the vend price for a
Hot Wash in Special Vend A.
How to Program Special Vend A Reg. Hot
Wash Vend Price
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 71
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
C762I
Figure 69
NOTE: The vend price can be set from 0 to 65,535.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable options
until “+017” appears in the VFD. Refer to
1
C795I
3
2
C860I
Figure 70
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 72
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C88
C828I
Figure 73
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START keypad to enter the
value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+018”, will appear
in the VFD.
NOTE: To program “+018” (Special Vend A Reg.
program other options, refer to the appropriate
section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
54
Programming NetMaster
4. When “+018” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Special Vend A Reg. Warm Wash Vend
Price. The fifth digit will appear in the VFD and
will flash one second on and one second off.
18. Special Vend A Reg. Warm
Wash Vend Price “+018”
This option allows the owner to set the vend price for a
Warm Wash in Special Vend A.
How to Program Special Vend A Reg.
Warm Wash Vend Price
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 76
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
C762I
Figure 74
NOTE: The vend price can be set from 0 to 65,535.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+018” appears in the VFD. Refer
1
94
C794I
3
2
C860I
Figure 75
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 77
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C88
C828I
Figure 78
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+019”, will appear
in the VFD.
NOTE: To program “+019” (Special Vend A Reg.
program other options, refer to the appropriate
section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
56
Programming NetMaster
4. When “+019” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Special Vend A Reg. Cold Wash Vend Price.
The fifth digit will appear in the VFD and will
flash one second on and one second off. Refer to
19. Special Vend A Reg. Cold Wash
Vend Price “+019”
This option allows the owner to set the vend price for a
Cold Wash in Special Vend A.
How to Program Special Vend A Reg. Cold
Wash Vend Price
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1”. If the vend price is $99.99 or less,
the fifth digit is “0”.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 81
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
C762I
Figure 79
NOTE: The vend price can be set from 0 to 65,535.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+019” appears in the VFD. Refer
1
C793I
3
2
C860I
Figure 80
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 82
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C88
C828I
Figure 83
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START keypad to enter the
value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+020”, will appear
in the VFD.
NOTE: To program “+020” (Special Vend A
program other options, refer to the appropriate
section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
58
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current value
displayed in the VFD to the desired value. Refer
20. Special Vend A Auto-Shutdown
Enable “+020”
This option, when turned on, will force the control to
shutdown during the Programmed Special Vend A
time period, preventing customers from starting a new
cycle after a selected time. “OFF” is displayed on the
VFD when Auto-Shutdown is active.
1
How to Program Special Vend A Auto-
Shutdown Enable
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 86
6. Press the START (enter) keypad when the
correct value appears in the VFD. The next option,
“+021”, will appear in the VFD.
C762I
Figure 84
NOTE: To program “+021” (Coin #1 Value), refer
appropriate section.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+020” appears in the VFD. Refer
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C792I
Figure 85
4. When “+020” appears in the VFD, press the
START (enter) keypad. The current Special
Vend A Auto-Shutdown Enable parameter value
will appear in the VFD. “0” will be displayed
when Auto-Shutdown is disabled and “255” will
be displayed when Auto-Shutdown is enabled.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Programming NetMaster
4. When “+021” appears in the VFD, press the
START (enter) keypad.There are five digits in
the Coin #1 Value. The fifth digit will appear in
the VFD and will flash one second on and one
21. Coin #1 Value “+021”
This option allows the owner to set a specific
numerical value for a coin entered. For example, in the
United States the coin value for one quarter would be
measured in cents (25). Therefore, the coin value
entered for one quarter would be 00025.
NOTE: If the coin value is $100.00 or more, the
fifth digit is “1”. If the coin value is $99.99 or less,
the fifth digit is “0”.
“.75”, and the Coin Value is set for “00025”, the vend
price displayed will decrease by .25 for each coin
entered.
How to Program Coin #1 Value
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 89
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
NOTE: The coin value can be set from 1 to 65,535.
1
C762I
Figure 87
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+021” appears in the VFD. Refer
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
91
C791I
Figure 90
Figure 88
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C89
C829I
Figure 91
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+022”, will appear
in the VFD.
NOTE: To program “+022” (Coin #2 Value), refer
appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Programming NetMaster
4. When “+022” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Coin #2 Value. The fifth digit will appear in
the VFD and will flash one second on and one
22. Coin #2 Value “+022”
This option allows the owner to set a specific
numerical value for a coin entered when using the dual
coin drop. For example, the coin value for a dollar
coin would be measured in cents (1.00). Therefore, the
coin value entered for one dollar coin would be 00100.
NOTE: If the coin value is $100.00 or more, the
fifth digit is “1”. If the coin value is $99.99 or less,
the fifth digit is “0”.
“2.00”, and the Coin Value is set for “00100”, the
vend price displayed will decrease by 1.00 for each
dollar coin entered.
How to Program Coin #2 Value
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 94
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
NOTE: The coin value can be set from 1 to 65,535.
1
C762I
Figure 92
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+022” appears in the VFD. Refer
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C790I
Figure 95
Figure 93
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C827I
Figure 96
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+023”, will appear
in the VFD.
NOTE: To program “+023” (Start Pulse Value),
to the appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Programming NetMaster
4. When “+023” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Start Pulse Value. The fifth digit will appear
in the VFD and will flash one second on and one
23. Start Pulse Value “+023”
This option allows the owner to program the value of
the Start Pulse if used for multiple pulses with an
after-market central card reader or pay system. Refer
NOTE: If the Start Pulse Value is $100.00 or more,
the fifth digit is “1”. If the Start Pulse Value is
$99.99 or less, the fifth digit is “0”.
How to Program Start Pulse Value
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 99
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
C762I
NOTE: The Start Pulse Value can be set from 1 to
65,535.
Figure 97
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+023” appears in the VFD. Refer
1
C789I
3
2
Figure 98
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 100
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 101
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+024”, will appear
in the VFD.
NOTE: To program “+024” (Default
program other options, refer to the appropriate
section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current number
to the desired number selected from Table 3 on
24. Default Cycle/Temperature
“+024”
This option allows the owner to set the default cycle
and temperature the machine will enter when in the
ready mode. When programming the default cycle,
refer to Table 3 on the following page.
1
How to Program Default Cycle/Temperature
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 104
C762I
6. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+025”, will appear in the VFD.
Figure 102
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+024” appears in the VFD. Refer
NOTE: To program “+025” (Power Fail Reset),
to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C788I
Figure 103
4. When “+024” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD. This number corresponds to the current
default cycle value.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
66
Programming NetMaster
How to Read Table 3
To determine the correct number required to program
Default Cycle/Temperature, use the following table.
The Default Value column contains the number
required in step 5. The other columns correspond to
individual options.
column’s option is turned on or off when the Default
Value is entered. Select the desired combination of
options and enter the number found in the Default Value
column.
Each column of options contains a unique combination
of the words “ON” and “OFF” that indicates if that
“+024”
Default
Value
Perm Press
Cycle
Delicate
Cycle
Normal Cycle
Hot Wash
Warm Wash
Cold Wash
9
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
10
12
17
18
20
33
34
36
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
Table 3
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
number to the desired number selected from
25. Power Fail Reset “+025”
This option allows the owner to set the amount of time
NetMaster will store active cycle information in the
event of a power failure. The default setting for Power
Fail Reset is OFF. If Power Fail Reset is turned OFF,
the cycle will be saved for up to six years.
1
How to Program Power Fail Reset
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 107
Figure 105
6. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+026”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+025” appears in the VFD. Refer
NOTE: To program “+026” (Set Real-Time Clock
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
87
C787I
Figure 106
4. When “+025” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD. This number corresponds to the current
Power Fail Reset setting.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
68
Programming NetMaster
How to Read Table 4
Use this table to set the amount of time for Power Fail
Reset.
If 133 is entered, the current cycle will be saved for up
to five minutes. If power is not restored within five
minutes, the control will erase the cycle status. The
minimum power failure time is five minutes. The
maximum power fail reset time is 127 minutes.
The table range begins at 0 and ends at 255. Numbers
entered between 0 and 127 turn the option OFF. If a
number in this range is entered, the current cycle status
will be saved for up to six years. When power is
restored, the cycle will begin where it was interrupted.
“+025”
NUMBER TO ENTER IN STEP 6
POWER FAIL RESET TIME
Turned OFF
000 – 127
Cycle will be saved for a minimum of 6 years
133
5 minutes without power before cycle is lost
. . . add one minute for every number up to
255
127 minutes without power before cycle is lost
Table 4
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the minutes to the
26. Set Real-Time Clock Minutes
“+026”
This option allows the owner to set NetMaster’s
internal clock to the correct time in minutes.
1
How to Program the Clock Minutes
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 110
Figure 108
6. Press the START (enter) keypad when the
correct time in minutes appears in the VFD. The
next option, “+027”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+026” appears in the VFD. Refer
NOTE: To program “+027” (Set Real-Time Clock
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
76
C786I
Figure 109
4. When “+026” appears in the VFD, press the
START (enter) keypad. The current time in
minutes will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
70
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the hours to the
27. Set Real-Time Clock Hours
“+027”
This option allows the owner to set NetMaster’s
internal clock to the correct time in hours.
1
How to Program the Clock Hours
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 113
Figure 111
6. Press the START (enter) keypad when the
correct time in hours appears in the VFD. The
next option, “+028”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+027” appears in the VFD. Refer
NOTE: To program “+028” (Set Real-Time Clock
refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C785I
Figure 112
4. When “+027” appears in the VFD, press the
START (enter) keypad. The current time in hours
will appear in the VFD.
NOTE: The hours will be displayed in military time.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the day until
28. Set Real-Time Clock Day “+028”
This option allows the owner to set NetMaster’s
internal clock to the correct day of the week.
NOTE: Sunday is considered day one (001),
Monday is day two (002) and so on.
How to Program the Clock Day
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
1
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
Figure 114
3
Press this pad (-) to scroll back or decrease a value
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+028” appears in the VFD. Refer
Figure 116
6. Press the START (enter) keypad when the
correct day appears in the VFD. The next option,
“+029”, will appear in the VFD.
NOTE: To program “+029” (Set Real-Time Clock
refer to the appropriate section.
How to Exit Programming Feature
C784I
1. Be sure the control shows a programmable option,
not a value.
Figure 115
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
4. When “+028” appears in the VFD, press the
START (enter) keypad. The current day of the
week will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
72
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the day of the
29. Set Real-Time Clock Date
“+029”
This option allows the owner to set NetMaster’s
internal clock to the correct day of the month.
1
How to Program the Clock Date
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 119
Figure 117
6. Press the START (enter) keypad when the
correct day of the month appears in the VFD. The
next option, “+030”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+029” appears in the VFD. Refer
NOTE: To program “+030” (Set Real-Time Clock
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
73
C783I
Figure 118
4. When “+029” appears in the VFD, press the
START (enter) keypad. The current day of the
month will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
73
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the month until
30. Set Real-Time Clock Month
“+030”
This option allows the owner to set NetMaster’s
internal clock to the correct month.
1
How to Program the Clock Month
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 122
Figure 120
6. Press the START (enter) keypad when the
correct month appears in the VFD. The next
option, “+031”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+030” appears in the VFD. Refer
NOTE: To program “+031” (Set Real-Time Clock
refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
72
C782I
Figure 121
4. When “+030” appears in the VFD, press the
START (enter) keypad. The current month will
appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
74
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the year until
31. Set Real-Time Clock Year
“+031”
This option allows the owner to set NetMaster’s
internal clock to the correct year.
NOTE: The year 2000 is “00”, the year 2001 is “01”
and so on.
How to Program the Clock Year
1. Control must be in Manual Mode. Refer to
1
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 123
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+031” appears in the VFD. Refer
Figure 125
6. Press the START (enter) keypad when the
correct year appears in the VFD. The next option,
“+032”, will appear in the VFD.
NOTE: To program “+032” (Set Real-Time Clock
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
71
C781I
Figure 124
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
4. When “+031” appears in the VFD, press the
START (enter) keypad. The current year will
appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
75
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the century until
32. Set Real-Time Clock Century
“+032”
This option allows the owner to set NetMaster’s
internal clock to the correct century.
NOTE: The digits “20” are used for century.
How to Program the Clock Century
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 126
Figure 128
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+032” appears in the VFD. Refer
6. Press the START (enter) keypad when the
correct century appears in the VFD. The next
option, “+033”, will appear in the VFD.
NOTE: To program “+033” (Normal Wash
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
70
C780I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 127
4. When “+032” appears in the VFD, press the
START (enter) keypad. The current century will
appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
76
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
33. Normal Wash Agitate Time
“+033”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of
wash agitate time for the Normal cycle.
NOTE: The Normal Wash Agitate Time can be set
from zero (0) to 15 minutes.
How to Program Normal Wash Agitate
Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 129
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+033” appears in the VFD. Refer
Figure 131
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+034”, will appear in the VFD.
NOTE: To program “+034” (Normal Extra Rinse
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
79
C779I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 130
4. When “+033” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Normal Wash Agitate Time
will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
77
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
34. Normal Extra Rinse Agitate
Time “+034”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of
extra rinse agitate time for the Normal cycle.
NOTE: The Normal Extra Rinse Agitate Time can
be set from zero (0) to 15 minutes.
How to Program Normal Extra Rinse
Agitate Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 132
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+034” appears in the VFD. Refer
Figure 134
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+035”, will appear in the VFD.
NOTE: To program “+035” (Normal Rinse Agitate
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C778I
C778I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 133
4. When “+034” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Normal Extra Rinse Agitate
Time will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
78
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
35. Normal Rinse Agitate Time
“+035”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of time
for a rinse agitate in the Normal cycle.
NOTE: The Normal Rinse Agitate Time can be set
from zero (0) to 15 minutes.
How to Program Normal Rinse Agitate
Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 135
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+035” appears in the VFD. Refer
Figure 137
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+036”, will appear in the VFD.
NOTE: To program “+036” (Normal Final Spin
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C796I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 136
4. When “+035” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Normal Rinse Agitate Time
will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
79
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
36. Normal Final Spin Time “+036”
This option allows the owner to set the amount of time
for a final spin in the Normal cycle.
number of minutes displayed in the VFD to the
How to Program Normal Final Spin Time
NOTE: The Normal Final Spin Time can be set
from zero (0) to 15 minutes.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
1
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
C762I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 138
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+036” appears in the VFD. Refer
3
Press this pad (-) to scroll back or decrease a value
Figure 140
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+037”, will appear in the VFD.
NOTE: To program “+037” (Permanent Press
other options, refer to the appropriate section.
77
C797I
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
Figure 139
4. When “+036” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Normal Final Spin Time will
appear in the VFD.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
80
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
37. Permanent Press Wash Agitate
Time “+037”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of
wash agitate time for the Permanent Press cycle.
NOTE: The Permanent Press Wash Agitate Time
can be set from zero (0) to 15 minutes.
How to Program Permanent Press Wash
Agitate Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 141
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+037” appears in the VFD. Refer
Figure 143
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+038”, will appear in the VFD.
NOTE: To program “+038” (Permanent Press
program other options, refer to the appropriate
section.
How to Exit Programming Feature
78
C798I
1. Be sure the control shows a programmable option,
not a value.
Figure 142
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
4. When “+037” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Permanent Press Wash
Agitate Time will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
81
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
38. Permanent Press Extra Rinse
Agitate Time “+038”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of
extra rinse agitate time for the Permanent Press cycle.
NOTE: The Permanent Press Extra Rinse Agitate
Time can be set from zero (0) to 15 minutes.
How to Program Permanent Press Extra
Rinse Agitate Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 144
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+038” appears in the VFD. Refer
Figure 146
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+039”, will appear in the VFD.
NOTE: To program “+039” (Permanent Press
other options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
79
C799I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 145
4. When “+038” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Permanent Press Extra Rinse
Agitate Time will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
82
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
39. Permanent Press Rinse Agitate
Time “+039”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of rinse
agitate time for the Permanent Press cycle.
NOTE: The Permanent Press Rinse Agitate Time
can be set from zero (0) to 15 minutes.
How to Program Permanent Press Rinse
Agitate Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 147
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+039” appears in the VFD. Refer
Figure 149
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+040”, will appear in the VFD.
NOTE: To program “+040” (Permanent Press
other options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C800I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 148
4. When “+039” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Permanent Press Rinse
Agitate Time will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
40. Permanent Press Final Spin
Time “+040”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of final
spin time for the Permanent Press cycle.
NOTE: The Permanent Press Final Spin Time can
be set from zero (0) to 15 minutes.
How to Program Permanent Press Final
Spin Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 150
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+040” appears in the VFD. Refer
Figure 152
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+041”, will appear in the VFD.
NOTE: To program “+041” (Delicate Wash
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C801I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 151
4. When “+040” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Permanent Press Final Spin
Time will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
84
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
41. Delicate Wash Agitate Time
“+041”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of
wash agitate time for the Delicate cycle.
NOTE: The Delicate Wash Agitate Time can be set
from zero (0) to 15 minutes.
How to Program Delicate Wash Agitate
Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 153
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+041” appears in the VFD. Refer
Figure 155
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+042”, will appear in the VFD.
NOTE: To program “+042” (Delicate Extra Rinse
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C802I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 154
4. When “+041” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Delicate Wash Agitate Time
will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
85
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
42. Delicate Extra Rinse Agitate
Time “+042”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of
extra rinse agitate time for the Delicate cycle.
NOTE: The Delicate Extra Rinse Agitate Time can
be set from zero (0) to 15 minutes.
How to Program Delicate Extra Rinse
Agitate Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 156
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+042” appears in the VFD. Refer
Figure 158
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+043”, will appear in the VFD.
NOTE: To program “+043” (Delicate Rinse
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C803I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 157
4. When “+042” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Delicate Extra Rinse Agitate
Time will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
86
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
43. Delicate Rinse Agitate Time
“+043”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of rinse
agitate time for the Delicate cycle.
NOTE: The Delicate Rinse Agitate Time can be set
from zero (0) to 15 minutes.
How to Program Delicate Rinse Agitate
Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 159
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+043” appears in the VFD. Refer
Figure 161
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+044”, will appear in the VFD.
NOTE: To program “+044” (Delicate Final Spin
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C804I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 160
4. When “+043” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Delicate Rinse Agitate time
will appear in the VFD.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
87
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
44. Delicate Final Spin Time “+044”
This option allows the owner to set the amount of final
spin time for the Delicate cycle.
number of minutes displayed in the VFD to the
How to Program Delicate Final Spin Time
NOTE: The Delicate Final Spin Time can be set
from zero (0) to 15 minutes.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
1
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
C762I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
Figure 162
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+044” appears in the VFD. Refer
3
Press this pad (-) to scroll back or decrease a value
Figure 164
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+045”, will appear in the VFD.
NOTE: To program “+045” (Warm Rinse Enable/
options, refer to the appropriate section.
How to Exit Programming Feature
C805I
1. Be sure the control shows a programmable option,
not a value.
Figure 163
4. When “+044” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Delicate Final Spin Time will
appear in the VFD.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
88
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-) keypad
to increase or decrease the current number to the
45. Warm Rinse Enable/Disable
“+045”
This option allows the owner to program an optional
warm fill temperature for the final rinse fill. If this
option is enabled and HOT or WARM water is
selected for the wash fill, warm water will be used for
the final rinse fill.
1
How to Program the Warm Rinse Enable/
Disable
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 167
6. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+046”, will appear in the VFD.
C762I
Figure 165
NOTE: To program “+046” (Control Configuration
options, refer to the appropriate section.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+045” appears in the VFD. Refer
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C806I
Figure 166
4. When “+045” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD. This number (found below) corresponds
to the current Warm Rinse Enable/Disable Value.
One (1) = Option Enabled
Zero (0) = Option Disabled
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
89
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
number to the desired number selected from
46. Control Configuration Data #1
“+046”
This option allows the owner to turn ON or turn OFF
preprogrammed capabilities within NetMaster.
1
How to Program the Control Configuration
Data #1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 170
Figure 168
6. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+047”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+046” appears in the VFD. Refer
NOTE: To program “+047” (Control Configuration
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C807I
Figure 169
4. When “+046” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD. This number corresponds to the current
Control Configuration Data #1 Value.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
90
Programming NetMaster
Configuration #1 Programming
on or turn off the preprogrammed daylight savings
option, wash temperature display option, infra-red
access option, decimal point option, EC Power Fail,
and the automatic collect option in NetMaster.
To change any or all of these configuration options,
review the following descriptions carefully and choose
Enter the appropriate value in step 5 on the previous
page.
Daylight Savings
This option automatically sets the clock in NetMaster to account for the time change during
Daylight Savings.
OFF= Turns off the automatic daylight savings option programmed in NetMaster.
ON = Turns on the automatic daylight savings option programmed in NetMaster.
Wash Temperature
This option determines if the temperature LEDs indicate the selected wash temperature during the
entire cycle or indicates fill temperature during each rinse.
OFF= Selected wash temperature remains on for entire cycle.
ON = LEDs indicate actual water temperature during every fill step. LEDs will be off during steps
when water is not filling in the wash drum.
Infra-red Access
Decimal Point
This option determines if a Micro-Wand can access or program NetMaster.
OFF= Turns off the infra-red access by the Micro-Wand.
ON = Turns on the infra-red access by the Micro-Wand.
This option determines if a decimal point is used when displaying the vend price (i.e. machines
using token currency may choose to remove the decimal point).
OFF= Turns off the decimal point from appearing in the VFD.
ON = Turns on the decimal point to appear in the VFD.
Automatic Collect
EC Power Fail
This option automatically collects all audit data information whenever the Micro-Wand
communicates with the control.
OFF= Turns off the automatic collect with the Micro-Wand.
ON = Turns on the automatic collect with the Micro-Wand.
This option determines if the European Community Power Fail feature is enabled. If enabled and a
power failure lasts at least two seconds, the control will require the user to press the START pad to
resume the cycle that was in operation at the time of the power failure.
OFF= Turns off the European Community Power Fail feature.
ON = Turns on the European Community Power Fail feature.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
“+046”
Config #1
Value
EC Power
Auto
Decimal
Point
Infra-red
Access
Wash Temp
Indicate
Daylight
Savings
Fail
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
Collect
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
144
145
146
147
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
Table 5
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
“+046” (continued)
Config #1
Value
EC Power
Fail
Auto
Decimal
Point
Infra-red
Access
Wash Temp
Daylight
Savings
Collect
Indicate
OFF
OFF
ON
148
149
150
151
152
153
154
155
156
157
158
159
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
Table 5
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
number to the desired number selected from
47. Control Configuration Data #3
“+047”
This option allows the owner to turn ON or turn OFF
preprogrammed capabilities within NetMaster.
1
How to Program the Control Configuration
Data #3
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 173
Figure 171
6. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+048”, will appear in the VFD.
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+047” appears in the VFD. Refer
NOTE: To program “+048” (Lucky Option), refer
appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C808I
c808i
Figure 172
4. When “+047” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD. This number corresponds to the current
Control Configuration Data #3 Value.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
94
Programming NetMaster
NOTE: Selecting “Ready Mode” for the available
output will turn off the available output after the
first pulse is received. Selecting “Until Start Mode”
will keep the available output on until the vend
price is satisfied. This feature is used for
Configuration #3 Programming
access for Manual Rapid Advance and Diagnostics,
and to change the Available Output Mode.
aftermarket card read or central pay systems.
“+047”
RADV/DIAG Access
Config #3 Value
Available
Ready Mode
0
1
2
3
OFF
OFF
ON
Until Start Mode
Ready Mode
ON
Until Start Mode
Table 6
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
the VFD. This number corresponds to the current
Lucky Option Programming Value.
48. Lucky Option “+048”
This option allows the owner to program the machine
to provide a free vend cycle to customers after a
certain number of machine cycles have occurred.
5. Locate the desired number in the first column of
For coin models, “FrEE” will be displayed five
minutes after the completion of the programmed
number of cycles has occurred. The cycle can then be
started by pressing the START (enter) pad.
“+048”
Lucky Option
Value
Lucky Cycle
ON/OFF
Number of
Cycles
1 – 127
129
OFF
ON
ON
ON
1 – 127
For card models, when a card is inserted, the VFD will
display “bAL” followed by the card balance. When the
user presses the START pad, a zero vend will be
deducted from the card. The VFD will display
“WAIT”. The VFD will then display “FrEE” for five
seconds and then the cycle time will be displayed.
When the card is removed, the VFD will flash the
remaining balance for three seconds and will then revert
back to the cycle time.
1
2
130
131 – 255
3 – 127
Table 7
6. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
How to Program Lucky Option
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
C762I
Figure 174
Figure 176
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+048” appears in the VFD. Refer
7. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+049”, will appear in the VFD.
NOTE: To program “+049” (Special Cycle
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C809I
C809I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 175
4. When “+048” appears in the VFD, press the
START (enter) keypad. A number will appear in
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
96
Programming NetMaster
5. Locate the desired number in the first column of
49. Special Cycle Option “+049”
This option allows the owner to program the machine
to offer extra wash time, extra rinse time, warm rinse,
or any combination of the above to the customers for
an added vend price.
6. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
How to Program Special Cycle Option
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 177
Figure 179
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+049” appears in the VFD. Refer
7. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+050”, will appear in the VFD.
NOTE: To program “+050” (Special Cycle Extra
Wash Time), refer to option 50. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
C810I
C812I
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
Figure 178
4. When “+049” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD. This number corresponds to the current
Special Cycle Option Programming Value.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
97
Programming NetMaster
How to Read Table 8
To determine the correct number required to program
Special Cycle Option, use the following table. The
Special Cycle Option Value column contains the
number required in step 6. The other columns
correspond to individual options.
Each column of options contains a unique combination
of the words “ON” and “OFF” that indicates if that
column’s option is turned on or off when the Special
Cycle Option Value is entered. Select the desired
combination of options and enter the number found in
the Special Cycle Option Value column.
“+049”
Special Cycle
Option Value
Special Cycle
ON/OFF
Warm Rinse ON/OFF
0
OFF
ON
ON
OFF
OFF
ON
128
129
Table 8
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
50. Special Cycle Extra Wash Time
“+050”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of
additional wash time for the Special Cycle.
NOTE: The Special Cycle Extra Wash Time can be
set from zero (0) to 15 minutes.
How to Program Special Cycle Extra
Wash Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 180
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+050” appears in the VFD. Refer
Figure 182
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+051”, will appear in the VFD.
NOTE: The Special Cycle option needs to be
Extra Wash Time to take effect.
NOTE: To program “+051” (Special Cycle Extra
other options, refer to the appropriate section.
C811I
C811I
How to Exit Programming Feature
Figure 181
1. Be sure the control shows a programmable option,
not a value.
4. When “+050” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Special Cycle Extra Wash
Time will appear in the VFD.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
99
Programming NetMaster
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
51. Special Cycle Extra Extra-Rinse
Time “+051”
number of minutes displayed in the VFD to the
This option allows the owner to set the amount of
additional extra rinse time for the Special Cycle.
NOTE: The Special Cycle Extra Extra-Rinse Time
can be set from zero (0) to 15 minutes.
How to Program Special Cycle Extra
Extra-Rinse Time
1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C762I
3
Press this pad (-) to scroll back or decrease a value
Figure 183
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+051” appears in the VFD. Refer
Figure 185
6. Press the START (enter) keypad when the
correct number of minutes appears in the VFD.
The next option, “+052”, will appear in the VFD.
NOTE: The Special Cycle option needs to be
Extra Extra-Rinse Time to take effect.
NOTE: To program “+052” (Smart Card
other options, refer to the appropriate section.
C812I
C812I
How to Exit Programming Feature
Figure 184
1. Be sure the control shows a programmable option,
not a value.
4. When “+051” appears in the VFD, press the
START (enter) keypad. The current number of
minutes set for the Special Cycle Extra Extra-
Rinse Time will appear in the VFD.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
100
Programming NetMaster
4. When “+052” appears in the VFD, press the
START (enter) keypad. There are five digits in
the Smart Card Maximum Value. The fifth digit
will appear in the VFD and will flash one second
52. Smart Card Maximum Value
“+052”
This option allows the owner to set the maximum card
balance that will be accepted. If a cash value card is
inserted with a balance greater than this value, it will
not be accepted.
NOTE: If the Smart Card Maximum Value is
$100.00 or more, the fifth digit is “1”. If the Smart
Card Maximum Value is $99.99 or less, the fifth
digit is “0”.
How to Program Smart Card Maximum
Value
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 188
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
C762I
1
Figure 186
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+052” appears in the VFD. Refer
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C813I
C813I
3
Press this pad (-) to scroll back or decrease a value
Figure 187
Figure 189
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C87
C827I
Figure 190
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+053”, will appear
in the VFD.
NOTE: To program “+053” (Site Code #1), refer to
option 53. To program other options, refer to the
appropriate section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
102
Programming NetMaster
4. When “+053” appears in the VFD, press the
START (enter) keypad. There are five digits in
Site Code #1. The fifth digit will appear in the
VFD and will flash one second on, one second
53. Site Code #1 “+053”
This option allows the owner to program a site code to
correspond with the Site Code #1 pricing. This allows
different pricing for a specific site code.
How to Program Site Code #1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
C826I
C826I
Figure 193
5. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
1
C762I
Figure 191
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+053” appears in the VFD. Refer
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
C840I
C840I
3
Press this pad (-) to scroll back or decrease a value
Figure 192
Figure 194
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one second on and one
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C868I
Figure 195
7. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the value of the
active digit and the START (enter) keypad to
enter the value of the digit and advance to the
next digit.
8. Press the START (enter) keypad with the last
active digit. The next option, “+054”, will appear
in the VFD.
NOTE: To program “+054” (Error Code
program other options, refer to the appropriate
section.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
104
Programming NetMaster
6. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
54. Error Code Programming
Parameter “+054”
This option allows the owner to turn on or turn off
certain errors in the control.
1
How to Program Error Code Programming
Parameter
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 198
C762I
7. Press the START (enter) keypad when the
correct number appears in the VFD. The next
option, “+055”, will appear in the VFD.
Figure 196
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+054” appears in the VFD. Refer
NOTE: To program “+055” (Start Pulse Mode),
to the appropriate section.
How to Exit Programming Feature
1. Be sure the control shows a programmable option,
not a value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
C815I
C815I
Figure 197
4. When “+054” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD. This number corresponds to the current
Error Code Programming Parameter Value.
5. Locate the desired number in the first column of
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
105
Programming NetMaster
How to Read Table 9
To determine the correct number required to program
Error Code Programming Parameter, use the following
table. The Error Code Value column contains the
number required in step 6. The other columns
correspond to individual options.
Each column of options contains a unique combination
of the words “ON” and “OFF” that indicates if that
column’s option is turned on or off when the Error
Code Value is entered. Select the desired combination
of options and enter the number found in the Error
Code Value column.
“+054”
Error Code Value
Drain Error
OFF
Fill Error
OFF
OFF
ON
Coin Error
OFF
0
1
OFF
ON
4
OFF
OFF
5
OFF
ON
ON
8
ON
OFF
OFF
ON
OFF
9
ON
ON
12
13
ON
OFF
ON
ON
ON
Table 9
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming NetMaster
5. Locate the desired number in the first column of
55. Start Pulse Mode “+055”
This option allows the owner to program the Start
Pulse Input. The Start Pulse Mode can be used for
after-market central pay or card systems. The central
system sends the start pulse to the Start Pulse Input of
the control to start the cycle. If set for single pulse, one
start pulse from the central system will start the cycle.
If set for multiple pulses, each pulse will deduct from
the vend price the value set up in option 23 (Start
Pulse Value) until the vend is satisfied.
“+055”
Start Pulse
Mode Value
Start Pulse
ON/OFF
Single Pulse/
Multiple Pulses
0
OFF
OFF
ON
Single Pulse
Multiple Pulses
Single Pulse
64
128
192
ON
Multiple Pulses
How to Program Start Pulse Mode
Table 10
1. Control must be in Manual Mode. Refer to
6. Press the DELICATES (+) or the COLD (-)
keypad to increase or decrease the current
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press
the START (enter) keypad and “+001” will
appear in the VFD.
1
C762I
Figure 199
3
2
C860I
3. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the programmable
options until “+055” appears in the VFD. Refer
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 201
7. Press the START (enter) keypad when the correct
number appears in the VFD.
NOTE: To program other options, refer to the
appropriate section.
C816I
C816I
How to Exit Programming Feature
Figure 200
1. Be sure the control shows a programmable option,
not a value.
4. When “+055” appears in the VFD, press the
START (enter) keypad. A number will appear in
the VFD. This number corresponds to the current
Start Pulse Mode Programming Value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
107
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Collecting Audit Information
This feature allows the owner to retrieve audit
Audit Options List
information stored in the washer by pressing a sequence
of pads on the control. For an explanation of the audit
options available, see the Audit Options List on this page.
VFD
Display
#
Description
“CyCL”
“COI1”
“COI2”
“PLSE”
“CArd”
1
2
3
4
5
Total # of machine cycles
Total # of coins #1
How to Enter Audit Feature
1. Control must be in Manual Mode to start. Refer
Total # of coins #2
to Entering the Manual Mode.
Total # of Start Pulses
2. Press the DELICATES (+) or the COLD (-)
202.
Smart Card Reader Firm Ware Version #
Table 11
2. Once the desired option appears in the VFD,
press the START (enter) keypad once to start the
audit count. At this point, the display will show
the first four-digit segment of the audit value.
Press the START (enter) keypad again to view the
last four digits of the number.
C823I
C823I
NOTE: The VFD can display up to 4 digits at one
time. All audit counts are separated into two 4-digit
segments. Each time the START (enter) keypad is
pressed in step 2, the VFD will show the next four-
digit segment in the audit value.
Figure 202
3. Press the START keypad. “CyCL” will appear.
If the procedure did not work, the control will return to
For Example: In the Total Number of Coins #1 option
with “COI1” displayed in the VFD, the audit has
counted 10,009 coins. Pressing the START (enter)
keypad one time will show “_ _ _ 1” to represent ten
thousand. Pressing the START (enter) keypad a second
time will display “0009” meaning nine. The total
equals “00010009” or 10,009.
How to Read Audit Data
1. Use the DELICATES (+) or the COLD (-)
keypad to scroll through various options until the
desired option is displayed in the VFD. Refer to
explanation of the audit options available. Refer to
3. Press the START (enter) keypad again. The
control will go to the next audit option in the
Audit Options List.
1
4. To select other audit options, repeat steps 1 – 4.
How to Exit Audit Feature
1. Be sure the control shows an audit option, not a
value.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand. The control will
3
2
C860I
1
2
Press this pad (+) to scroll forward or increase a value
Press this pad (enter) to choose a selected value or
option
3
Press this pad (-) to scroll back or decrease a value
Figure 203
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
109
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Reset
This feature allows the owner to reset the washer
control’s programming data to the factory default
settings by pressing a sequence of pads on the control.
For an explanation of the Factory Default Settings,
refer to Default Washer Settings.
How to Enter Manual Reset
1. Control must be in Manual Mode to start.
Refer to Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
204.
C80
C830I
Figure 204
3. Press the START (enter) keypad. The control will
display “WAIT” until the programming is
complete. Once the program has been reset, the
control will revert back to the ready mode.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
111
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing Machine and
Electronic Control Functions
This feature allows the owner to run diagnostic tests
on various washer operations without servicing the
washer. The following tests are available:
How to Enter Testing Feature
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
●
●
●
●
●
●
●
●
●
●
●
●
●
Control Software Version Number
Pressure Switch Opening Test
Service Door Opening Test
Coin Vault Opening Test
Coin Drop #1 Input Test
Coin Drop #2 Input Test
Lid Switch Input Test
2. Press the DELICATES (+) or the COLD (-)
keypad until “dIAg” appears.
3. Press the START (enter) keypad. Display will
change to “+001” indicating the control software
version number test.
4. Press the DELICATES (+) or the COLD (-)
keypad to scroll through the diagnostic test
options.
How to Start Tests
Show Fill Time Test
Show Drain Time Test
To start a diagnostic test, refer to the quick reference
keypad when the desired test # is displayed. For detailed
information on each test, read the appropriate description.
Start Pulse Test
Configuration #1 Display Test
Configuration #2 Display Test
Configuration #3 Display Test
How to Exit Testing Feature
While pressing and holding the NORMAL keypad
with one hand, press the PERM PRESS keypad with
the other hand. The display will return to the ready
Diagnostic (Testing) Mode – Quick Reference Chart
Test Number
Diagnostic Mode
VFD Display
“SXXX”
“S:XX”
1
2
Control Software Version # Test
Service Door Opening Test
Coin Vault Opening Test
Coin Drop #1 Input Test
Coin Drop #2 Input Test
Lid Switch Input Test
“U:XX”
“C1:XX”
“C2:XX”
“L:XX”
3
4
5
6
“PXXX”
“FX:XX”
“dX:XX”
“ST:XX”
“AXXX”
“bXXX”
“CXXX”
7
Pressure Switch Opening Test
Show Fill Time Test
8
9
Show Drain Time Test
10
11
12
13
Start Pulse Test
Configuration #1 Display Test
Configuration #2 Display Test
Configuration #3 Display Test
Table 12
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing Machine and Electronic Control Functions
Diagnostic Test Descriptions
Control Software Version Number Test
Coin Drop #1 Input Test
This option displays the control software version
number. To start test, control must be in the Testing
Mode. Refer to “How to Start Tests” at the beginning
of this section.
This option tests coin drop #1. To start test, control
must be in the Testing Mode. Refer to “How to Start
Tests” at the beginning of this section.
To enter, press the START (enter) keypad. The VFD
display will show “C1:XX”. The “XX” will show the
number of coins entered. This test will add counts to
the total number of test coins #1 counter. Refer to
Collecting Audit Information.
To enter, press the START (enter) keypad. The VFD
display will show “SXXX” where “XXX” is the
software version number.
To exit the Software Version Number Test, press the
NORMAL and PERM PRESS keypads. The control
To exit the Coin Drop #1 Input Test, press the
NORMAL and PERM PRESS keypads. The control
Service Door Opening Test
Coin Drop #2 Input Test
This option tests the service door switch. To start test,
control must be in the Testing Mode. Refer to “How to
Start Tests” at the beginning of this section.
This option tests coin drop #2. To start test, control
must be in the Testing Mode. Refer to “How to Start
Tests” at the beginning of this section.
To enter, press the START (enter) keypad. The VFD
display will show “S:XX”. The “XX” will show the
number of service door openings.
To enter, press the START (enter) keypad. The VFD
display will show “C2:XX”. The “XX” will show the
number of coins entered. This test will add counts to
the total number of test coins #2 counter. Refer to
Collecting Audit Information.
The service door switch has to be closed for at least
one second and opened for at least a half a second to
make a valid count. This test will add counts to the
service door opening counter for the audit and save the
date/time for each opening of the test.
To exit the Coin Drop #2 Input Test, press the
NORMAL and PERM PRESS keypads. The control
To exit the Service Door Opening Test, press the
NORMAL and PERM PRESS keypads. The control
Lid Switch Input Test
This test will display whether the washer lid is open or
closed.
Coin Vault Opening Test
This option tests the coin vault switch. To start test, the
control must be in the Testing Mode. Refer to “How to
Start Tests” at the beginning of this section.
To start test, control must be in the Testing Mode.
Refer to “How to Start Tests” at the beginning of this
section.
To enter, press the START (enter) keypad. The VFD
display will show “U:XX”. The “XX” will show the
number of coin vault openings.
To enter, press the START (enter) keypad. If the lid is
closed, the VFD will display “L:CL”. If the lid is open,
the VFD will display “L:OP”.
The coin vault switch has to be closed for at least one
second and opened for at least a half a second to make
a valid count. This test will add counts to the coin vault
opening counter for the audit and save the time/date
for each opening of the test.
To exit the test, press the NORMAL keypad with one
hand, then press the PERM PRESS keypad with the
other hand. The control will return to the ready mode.
To exit the Coin Vault Opening Test, press the
NORMAL and PERM PRESS keypads. The control
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
114
Testing Machine and Electronic Control Functions
To enter, press the START (enter) keypad. The VFD
display will show “ST:XX”. The “XX” will show the
number of pulses entered. This test will add counts to
the total number of Start Pulses counter. Refer to
Collecting Audit Information.
Pressure Switch Input Test
This test will display whether the pressure switch is
open or closed.
To start test, control must be in the Testing Mode.
Refer to “How to Start Tests” at the beginning of this
section.
To exit the Start Pulse Test, press the NORMAL and
PERM PRESS keypads. The control will return to the
To enter, press the START (enter) keypad. The VFD
display will show “P:OP” if the pressure switch is
open and “P:CL” if the pressure switch is closed.
Configuration Display Test
This option shows the machine configuration values.
Test #11 shows configuration value #1, Test #12 shows
configuration value #2, and Test #13 shows configuration
value #3. To start test, control must be in the Testing
Mode. Refer to “How to Start Tests” at the beginning
of this section.
To exit the test, press the NORMAL keypad with one
hand, and then press the PERM PRESS keypad with
the other hand. The control will then return to the
Show Fill Time Test
To enter, press the START (enter) keypad. For
configuration value #1, the VFD will show “AXXX”.
For configuration value #2, the VFD will show “bXXX”.
For configuration value #3, the VFD will show
“CXXX”. For all, “XXX” is the value of the number.
This test will display the average fill time in minutes
and seconds. This average will be calculated by taking
the average of the last four (4) fill times.
To start test, control must be in the Testing Mode.
Refer to “How to Start Tests” at the beginning of this
section.
Refer to tables below for test information.
To exit a Configuration Display Test, press the
NORMAL and PERM PRESS keypads. The control
To enter, press the START (enter) keypad. The VFD
will show “FX:XX”. The “X:XX” will be the average
fill time in minutes and seconds for that machine.
Machine Configuration #1 Table
To exit the Show Fill Time Test, press and hold the
NORMAL keypad with one hand, then press the
PERM PRESS keypad with the other hand. The control
Value
129
Coin #1
NO
Coin #2
NO
161
YES
NO
NO
Show Drain Time Test
193
YES
YES
This test will display the average drain time in minutes
and seconds. The average drain time is calculated by
taking the average of the last four (4) drain times.
225
YES
Table 13
To start the test, press the START (enter) keypad. The
VFD will show “dX:XX”. The “X:XX” will be the
average drain time in minutes and seconds for that
machine.
Machine Configuration #2 Table
Smart Card
Value
Network Board
Reader
0
NO
NO
NO
To exit the Show Drain Time Test, press and hold the
NORMAL keypad with one hand, then press the
PERM PRESS keypad with the other hand. The control
32
64
96
YES
NO
YES
YES
YES
Start Pulse Test
Table 14
This option tests the Start Pulse. To start test, control
must be in the Testing Mode. Refer to “How to Start
Tests” at the beginning of this section.
Machine Configuration #3 – unused.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
115
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Codes
Following is a list of possible error codes for an
electronic control. Errors beginning with “EI” refer to
NetMaster Infra-red communication errors. Errors
beginning with “EC” refer to NetMaster card reader
errors. All other errors refer to electronic control
errors.
Cause/
Display
EI:01
Description
Transmission Failure
Corrective Action
Communication failure. Re-aim Micro-Wand and try
again.
EI:02
EI:03
EI:04
EI:05
EI:06
Device Timeout
Communication failure. Re-aim Micro-Wand and try
again.
Invalid Command Code
Expecting Upload Request
Invalid or Out-of-Range Data
Invalid Data Code
Incorrect machine type. Before downloading, ensure
data is for current machine type.
Communication failure. Re-aim Micro-Wand and try
again.
Incorrect machine type. Before downloading, ensure
data is for current machine type.
Incorrect machine type. Before downloading, ensure
data is for current machine type.
EI:07
EI:08
EI:09
Error Writing to RTC
Error Writing to EEPROM
CRC-16 Error
Control failure. Replace control.
Control failure. Replace control.
Communication failure. Re-aim Micro-Wand and try
again.
EI:0A
EI:0F
Invalid Machine Type
Incorrect machine type. Before downloading, ensure
data is for current machine type.
Invalid Wakeup or Infra-red Disabled
Communication failure or infra-red is disabled.
Manually enable infra-red on control or re-aim Micro-
Wand and try again.
EC:00
EC:02
EC:03
General Communication Error
Timeout Error
Communication failure. Try card again.
Communication failure. Try card again.
Invalid Command Code
Incorrect machine type. Before downloading, ensure
data is for current machine type.
EC:05
EC:06
Invalid or Out-of-Range Data
Invalid Data Code
Incorrect machine type. Before downloading, ensure
data is for current machine type.
Incorrect machine type. Before downloading, ensure
data is for current machine type.
EC:09
EC:0A
Corrupted Data Error
Invalid Machine Type
Communication error. Try card again.
Incorrect machine type. Before downloading, ensure
data is for current machine type.
EC:19
No Card Reader Communication
Communication failure. Power down, power up and try
again. If error persists, replace control or card reader.
Table 15
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Codes
Cause/
Display
Description
Unreadable Card
Corrective Action
EC:20
Faulty card or dirty contact. Clean chip on card or card
reader contacts. Try card again. If error persists, card
may be faulty.
EC:21
EC:22
EC:23
Security ID Mismatch
Incorrect card. Use card with correct security code.
Incorrect card. Use card with correct site code.
Site Code Mismatch
Card Maximum Value Exceeded
Value on card over max. Use a card which does not
exceed maximum value.
EC:24
Insufficient Memory on Card
Card memory is full. Download card contents to PC and
clear card for re-use.
EC:25
EC:26
EC:27
EC:28
EC:29
EC:2A
EC:2b
EC:2C
EC:2d
Card Reader Malfunction
Faulty card reader. Replace card reader.
Try card again. If error persists, card may be faulty.
Faulty card reader. Replace card reader.
Faulty card reader. Replace card reader.
Faulty card reader. Replace card reader.
Faulty card reader. Replace card reader.
Card Write Error
Diagnostic Test Card Write Failure
Diagnostic Test Card Read Failure
Diagnostic Test Memory Test Failure
Diagnostic Test Card Interface Failure
Diagnostic Test Flash Checksum Failure Faulty card reader. Replace card reader.
Biberon or Non-biberon Device Failure
Faulty card reader. Replace card reader.
Firmware load failed. Replace card reader.
Firmware Update Failed,
S/W (Software) Intact
EC:2E
EC:2F
EC:30
EC:31
EC:50
EC:56
Firmware Update Failed, S/W Not Intact Faulty firmware in reader. Replace card reader.
Firmware Updated, S/W Not Intact
Timeout Error
Faulty firmware in reader. Replace card reader.
Replace card reader.
Hotlisted Card Inserted Into Reader
Loyalty Purse Read Error
Loyalty Purse Write Error
Card hotlisted. Control will destroy card.
Try card again. If error persists, card may be faulty.
Try card again. If error persists, card may be faulty.
Right most Network Communication Error
DP (decimal
point)
Communication problem. Wait for 1.5 minutes for error
to clear. If error doesn’t clear, power-down and power-
up the machine. If error persists, replace control or
network board.
Lit
Alrm
OFF
E:FL
Break-in Alarm Error
Break-in Alarm Shutdown Error
Fill Error
Service the door or coin vault switches.
Service the door or coin vault switches.
Pressure switch fails to open in 30 minutes in any fill
agitate cycle.
E:dr
Drain Error
Maximum drain time exceeded or water sensed at end of
spin step.
Table 15
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
118
Error Codes
Cause/
Display
Err
Description
Corrective Action
Coin Error
Invalid coin pulse or inoperative coin sensor. Check coin
drop area and remove obstructions. If error persists,
tampering may have occured. Evaluate security
procedures.
Table 15
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales Floor Feature
The Sales Floor feature is used on a sales floor to
allow the owner to turn on the entire VFD display and
all LEDs.
How to Exit Sales Floor Feature
1. Be sure service door is open.
2. While pressing and holding the NORMAL
keypad with one hand, press the PERM PRESS
keypad with the other hand.
How to Enter Sales Floor Feature
1. Control must be in Manual Mode to start. Refer
to Entering the Manual Mode.
The display will return to the ready mode. Refer to
2. Press the DELICATES (+) or the COLD (-)
keypad until “SHOW” appears.
3. Press the START (enter) keypad.
The display will light up.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
121
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Rapid Advance Feature
The Rapid Advance feature allows the owner to
quickly advance through active cycles or advance into
a cycle from the ready mode.
How to Exit Rapid Advance Feature
1. Advance through the cycles until reaching the
How to Enter Rapid Advance from
Ready Mode
NOTE: The Rapid Advance/Diagnostic Access
option must be turned on for Rapid Advance to
NetMaster.
1. If control is in Ready Mode, control must be put
into Manual Mode. Refer to Entering the
Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “rAPd” appears in the display.
3. Press the START (enter) keypad. The VFD will
display cycle time and the START (enter) keypad
LED will flash.
4. Press the START (enter) keypad to start cycle.
How to Enter Rapid Advance During
an Active Cycle
1. Be certain service door is open.
2. While pressing and holding the NORMAL
keypad with one hand, press the HOT keypad
with the other hand. There will be no change on
the VFD display.
Control may be in an active cycle or in the ready mode
to use the Rapid Advance feature.
While in the Rapid Advance Mode, pressing the
START (enter) keypad will advance the washer to the
next cycle step. The cycle indicator lights will tell
which cycle step the washer is in.
For Example: If the washer is in the wash fill/agitate
cycle step, pressing the START (enter) keypad will
advance the washer into the WASH PAUSE cycle step.
Continue pressing the START (enter) keypad until the
cycle is completed.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
123
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear Vend Feature
The Clear Vend feature allows the owner to clear a
control which is in the middle of satisfying a vend
price, and set it back to the ready mode.
How to Clear Vend
1. Open the service door. Refer to Opening the
Service Door.
2. While pressing and holding the HOT keypad with
one hand, press the PERM PRESS keypad with
the other hand. The control will reset to the ready
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
125
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Fail Recovery
The Power Fail Recovery feature allows the cycle status
to be saved in memory in the event of a power failure.
Power Fail Reset Enabled
If the length of the power failure is less than the
programmed Power Failure Reset time, the control
will resume the cycle from the point it left off. The
cycle will resume automatically unless the EC Power
Fail feature is enabled and the failure lasted more than
two (2) seconds which requires the user to press the
START pad.
If a cycle is in progress when the power fails, the cycle
status is saved in memory. When power recovers, the
control will determine whether to automatically
continue the cycle from the point it left off, requiring
the user to press the START pad to continue the cycle,
or end the cycle and put the control into the Ready
Mode.
If the power failure lasted more than the programmed
power failure reset time, the contol will end the cycle
and will return to the Ready Mode. If, however, the
cylinder is filled with water when the power recovers,
the control will not go directly to Ready Mode, but
will spin out the water first. In this case the control
will enter the Start Mode at the Rinse Spin #1 step of
the DELICATE Cycle prompting the user to press the
START pad. Once the START pad is pressed, the
control will start the Rinse Spin #1 step, then the Final
Spin step and then end the cycle.
Power Fail Reset Disabled
If the European Community (EC) Power Fail feature is
disabled, the control will automatically resume the
cycle from the point it left off. Whenever the EC
Power Fail feature is enabled and the power failure
lasted more than two (2) seconds, the control will go
back to the Start Mode and will prompt the user to
press the START pad to continue the cycle from the
point it left off.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
127
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Communications Mode
Infra-red Communications
Card Reader Communications
(Card Models Only)
The Infra-red Communications feature allows the
washer control to communicate with the Micro-Wand
IIIE. The washer control can be programmed and have
its data read without using the keypad. It may also be
used to start and stop various diagnostic tests.
The Card Reader Communications feature allows the
washer control to communicate with the Card Reader.
The washer control can be programmed and have its
data read without using the keypad.
How to Begin Communications with
Micro-Wand IIIE
Network Communications
The Network Communications feature allows the
washer control to communicate with the Network. The
washer control can be programmed and have its data
read without using the keypad.
The control will go blank and the VFD will display
“-C-” until the communication is complete. The
display will return to the previous mode. If an error
occurs that terminates communication, the VFD will
display “EI:XX” (“XX” represents the error code).
NOTE: The Infra-red Communications option
Programming NetMaster.
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
129
Notes
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Default Washer Settings
Default Settings
Default Cycle
The cycle listed is the default PERM PRESS cycle
Cycle
PERM PRESS
WARM
programmed in at the factory. This cycle can be made
longer or shorter by reprogramming the agitate times.
Refer to Programming NetMaster section to change
these times. All other times are not programmable.
Wash Water Temperature
Rinse Water Temperature
Special Vends
COLD
OFF. All items zero.
Cycle
Default
Signals:
Wash Fill
Wash Agitate
Wash Pause
2:00
10:00*
0:10
0:00
1:30
0:30
1:30
0:00
0:00*
0:00
0:00
3:00
2:00
4:00*
0:10
0:00
1:30
6:00*
Keypress
End of Cycle
Coin Input/Card Insertion ON
ON
OFF
Wash Pump
Remove Card
Coin #1 Value
Coin #2 Value
Power Fail Reset
ON
Wash Spin #1
Wash Spin/Spray
Wash Spin #2
Extra Rinse Fill
Extra Rinse Agitate
Extra Rinse Pause
Extra Rinse Pump
Extra Rinse Spin #1
Rinse Fill
Rinse Agitate
Rinse Pause
Rinse Pump
Rinse Spin #1
Final Spin
.25
1.00
OFF/5 minutes
Control Configuration:
Daylight Savings
Wash Temp Indicator
Infra-red Access
Decimal Point
ON
SELECT (OFF)
ON
ON
ON
OFF
Auto Collect
EC Power Fail
* = Programmable Times
210140
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Acoustic Research Speaker System HC6 User Manual
AEG Refrigerator K 7 10 43 4 I User Manual
Agilent Technologies Video Games E8285A User Manual
Agilent Technologies Water Dispenser Model A08xx User Manual
Aiphone Intercom System IS Series User Manual
AKG Acoustics Microphone C 426B User Manual
American Dish Service Dishwasher 5 CD LF RF User Manual
American Standard Laminate Trimmer Reliant 3 Bath and Shower Trim Kits with EverClean Finish User Manual
Axor Plumbing Product 14876001 User Manual
Axxess Interface Automobile Parts OESWC LAN29 STK User Manual