|
PANEL PC 1000
All-in-One 10.4”
Super Slim PANEL PC
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Approvals
!"CE Marking
!"FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or reloc a te the rec eiving a ntenna .
2. Inc rea se the sepa ra tion between the equipment a nd
rec eiver.
3. C onnec t the equipment into a n outlet on a c irc uit
different from tha t to whic h the rec eiver is c onnec ted.
4. C onsult the dea ler or a n experienc ed ra dio/TV
tec hnic ia n for help.
Shielded interface cables must be used in order to comply with
emission limits.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Before getting started, read the following important cautions.
1. The PANEL PC 1000 does not c ome equipped with a n
opera ting system. An opera ting system must be loa ded
first before insta lling a ny softwa re into the c omputer.
2. Be sure to ground yourself to prevent sta tic c ha rge when
insta lling the interna l c omponents. Use a grounding wrist
stra p a nd pla c e a ll elec tronic c omponents in a ny
sta tic -shielded devic es. Most elec tronic c omponents a re
sensitive to sta tic elec tric a l c ha rge.
3. Disc onnec t the power c ord from the PANEL PC 1000
before ma king a ny insta lla tion. Be sure both the system
a nd the externa l devic es a re turned OFF. Sudden surge
of power c ould ruin sensitive c omponents. Ma ke sure the
PANEL PC 1000 is properly grounded.
4. The brightness of the fla t pa nel displa y dec rea ses with
usa ge. However, hours of use va ry depending on the
a pplic a tion environment.
5. Turn OFF the system power before c lea ning. C lea n the
system using a c loth only. Do not spra y a ny liquid c lea ner
direc tly onto the sc reen. The PANEL PC 1000 ma y c ome
with or w/o a touc h sc reen. Although the touc h sc reen is
c hemic a l resista nt, it is rec ommended tha t you spra y the
liquid c lea ner on a c loth first before wiping the sc reen. In
c a se your system c omes without the touc h sc reen, you
must follow the sa me proc edure a nd not spra y a ny
c lea ner on the fla t pa nel direc tly.
6. Avoid using sha rp objec ts to opera te the touc h sc reen.
Sc ra tc hes on the touc h sc reen ma y c a use ma lfunc tion
or interna l fa ilure to the touc h sc reen.
7. The fla t pa nel displa y is not susc eptible to shoc k or
vibra tion. When a ssembling the PANEL PC 1000, ma ke
sure it is sec urely insta lled.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Do not open the system’s ba c k c over. If opening the
c over for ma intena nc e is a must, only a tra ined
tec hnic ia n is a llowed to do so. Integra ted c irc uits on
c omputer boa rds a re sensitive to sta tic elec tric ity. To
a void da ma ging c hips from elec trosta tic disc ha rge,
observe the following prec a utions:
#"Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity on
your body.
#"When handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.
Trademarks Acknowledgments
AC NODES is a tra de ma rk of AC NODES Inc .
ALI is a tra de ma rk of Ac e r La bora torie s, Inc .
AMD is a tra de ma rk of Adva nc e d Mic ro De vic e s, Inc .
AMI is a tra de ma rk of Ame ric a n Me ga tre nds, Inc .
C yrix is a tra de ma rk of C yrix C orpora tion.
ELO is a tra de ma rk of ELO Touc h Syste ms, Inc .
IBM, PC /AT, PS/2, VG A a re tra de ma rks of Inte rna tiona l
Busine ss Ma c hine s C orpora tion.
Inte l a nd Pe ntium a re tra de ma rks of Inte l C orpora tion.
MS-DOS, Mic rosoft C a nd Quic k BASIC a re tra de ma rks of
Mic rosoft C orpora tion.
SMC is a tra de ma rk of Sta nda rd Mic rosyste ms
C orpora tion.
C &T is a tra de ma rk of C hips a nd Te c hnologie s, Inc .
SST is a tra de ma rk of Silic on Stora ge Te c hnology, Inc .
UMC is a tra de ma rk of Unite d Mic roe le c tronic s
C orpora tion.
Othe r bra nd na me s a nd tra de ma rks a re the prope rtie s of
the ir re spe c tive ow ne rs.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
This page does not contain any information.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 Introduction ------------------------------- 1
1.1
1.2
1.3
1.4
1.5
General Description......................................... 1
Specifications .................................................. 2
Dimensions...................................................... 4
I/O Outlets........................................................ 5
Utilities Supported........................................... 6
Chapter 2 System Configuration ------------------ 7
2.1
System Configuration ...................................... 7
2.1.1 Front Vie w ............................................................... 7
Panel Mount..................................................... 8
2.2
Chapter 3 System Installation --------------------- 9
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
CPU.................................................................10
DRAM..............................................................10
HDD.................................................................11
4 x Serial Ports ...............................................12
Parallel Port ....................................................13
VGA.................................................................13
Ethernet ..........................................................13
Digital I/Os ......................................................14
Keyboard ........................................................14
3.10 PS/2 Mouse .....................................................14
3.11 External FDD...................................................15
3.12 Expansion Slot................................................16
3.13 System O/S and Software Installation.............17
Appendix A Power Supply Specifications---- 19
Standard AC Power Supplies ...................................19
Optional DC Power Supplies ....................................21
vii
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
This page does not contain any information.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
C h a p t e r 1
Introduction
This chapter contains the general information and the detailed
specifications of the PANEL PC1000. Chapter 1 includes the following
sections:
$"G enera l Desc ription
$"System Spec ific a tion
$"Dimensions
$"I/O Outlets
$"Utilities Supported
1.1 General Description
The PANEL PC 1000 super slim industrial PANEL PCs are mainly
designed for industrial automation and some space-constricted
embedded applications. For some space-concerned industries, a
traditional PC with a separate main system, display monitor and
keyboard is simply not integrated enough.
Ruggedly designed, the PANEL PC 1000 is 100% IBM PC/AT
compatible and it integrates super I/Os, VGA, 10.4” TFT, touch screen,
Ethernet, and packs special industrial features like watchdog timer,
CMOS double backup, all in a single system. The full PC
functionality coupled with its industrial-grade construction easily tailors
the system for any embedded applications and allows the system to
endure continuous operation in any hostile industrial environments
where stability and reliability are a must. Common applications of the
PANEL PC 1000 include tooling machine, POI terminal, stand-alone
KIOSK, medical instrument, mobile communication device and
banking system - to name just a few.
Designed by the PC experts for PC professionals, the PANEL PC
1000 is virtually the ultimate one-step solution for your space-limited
applications.
1
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
1.2 Specifications
Core System for system board
$"C PU: Inte l C e le ron 300 up to 733 MHz;
Inte l Pe ntium III 500 up to1.0G hz
$"System C hipset: Inte l 440BX C ore Logic C ontrolle r
$"BIOS: Awa rd BIO S, Y2K c omplia nt
2Mbit Fla sh RO M, DMI, Plug a nd Pla y
$"System Memory: O ne 168-pin DIMM (PC -100)
Ma ximum SDRAM of up to 256MB
$"L2 C a c he: Inte gra te d in C PU
$"Rea l Time C loc k: Da lla s STM48T86PC 1 or la te st produc t
$"Wa tc hdog Timer: Syste m re se t or Non-Ma sk Inte rrupt
softwa re progra mma ble Time inte rva l a nd
jumpe r se le c ta ble ;
64 le ve ls, 0.5~8 / 5~80 / 50~800 / 100~1600
se c onds
I/O System
$"Sta nda rd I/O:
− 4 x se ria l ports with powe r; 3 x RS-2 3 2 , 1 x
RS-2 3 2 / 4 2 2 / 4 8 5 jum pe r se le cta ble
− 1 x pa ra lle l port, SPP/ EPP/ ECP
− 1 x Exte rna l FDD Inte rfa ce
− 2 x HDD Inte rfa ce
− 1 x Ke yboa rd Inte rfa ce
− 1 x PS/ 2 Mouse Inte rfa ce
− 2 x USB Ports
$"Digita l I/O: Input x 4, O utput x 4
$"Ethernet:
− 3 2 -bit Plug & Pla y Fa st Ethe rne t Controlle r
− RJ-4 5 conne ctor
$"Audio:
− ESS Solo-1 1 9 3 8 3 2 -bit PCI 2 .1 Audio Drive controlle r
$"VG A/Fla t Pa nel C ontroller:
− AGP Inte rfa ce C&T6 9 0 0 0 controlle r with inte gra te d 2 MB
SDRAM
− Sim ulta ne ously supports CRT a nd fla t pa ne l displa ys
Introduction
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
Built-in P eripherals
$"Sta nda rd 100W pow e r supply
$"2.5” Ha rd disk (540MB or up)
$"10.4” ELO a nti-gla re a na log re sistive touc h sc re e n w ith
RS- 232 c ontrolle r sha ring C OM3
$"Syste m c ooling fa n
NOTE:
Optional DC power supplies rate d at +12V, +24V and
+48V are also available . (Se e Appe ndix A)
System Specification
$"10.4” TFT w ith 640 x 480 re solution
$"Exte rna l FDD inte rfa c e
$"NEMA 4/12 se a le d front pa ne l
$"He a t dispe nsing de sign
$"PC /104 e xpa nsion Bus
$"One fre e slot for PC I/ISA e xpa nsion
$"Net weight: 4.2 KG S
$"Dimension (ma in body size):
− PANEL PC 1 0 0 0
− 3 3 0 x 2 6 6 x 9 3 m m (with
one ISA or PCI e xpa nsion
ca rd)
$"Opera ting Tempera ture Ra nge: 0oC ~ 40oC
$"Rela tive Humidity: 5% ~ 95%; non-c onde nsing
NOTE:
For more de taile d information on the syste m e ngine
board use d in your PANEL PC , re fe r to the syste m board
User’s Manual that c ame with the system pac kaging.
3
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
1.3 Dimensions
PANEL1000-370 10.4" FLAT PANEL PC (unit: mm)
Introduction
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
1.4 I/O Outlets
The following figure shows the I/O arrangement of the PANEL PC
1000. The backside of the chassis contains most of the connectors.
1. Ethernet RJ-45 phone
ja c k
8. C OM3
9. C OM2
2. PS/2 mouse
3. Keyboa rd
4. Externa l FDD
10. C OM1
11. VG A port IF
12. AC inlet
5. 4-c ha nnel Digita l
Inputs/outputs
6. Pa ra llel port
7. C OM4
13. Power switc h
14. +5V/12V DC outlet
5
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
1.5 Utilities Supported
%"Watchdog Utility
%"Ethernet Utility
%"VGA Drivers
%"Touch screen Utility
Introduction
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
C h a p t e r 2
System Configuration
This chapter details the system parts and components with figures.
Sections include
$"System Ma jor Pa rts
$"Pa nel Mount
2.1 System Configuration
2.1.1 Front View
The figure below shows the front views of PANEL PC1000.
3
2
1
1.
2.
3.
Power LED
HDD LED
Ethernet LED
System Configuration
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
2.2 Panel Mount
The PANEL PC 1000 is mainly designed for panel mount application.
To mount the PANEL PC 1000, the standard set of mounting kit
(included in the system packaging) is needed. Please refer to the
following figure.
8
System Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
C h a p t e r 3
System Installation
This chapter describes the installation and the cable connection to the
system connectors. See system board User’s Manual that came with
your PANEL PC packaging for more details. Sections in this chapter
includes
$"C PU
$"DRAM
$"HDD
$"VG A
$"Expa nsion
Slot
$"Ethernet
$"Digita l I/O
$"Keyboa rd
$"PS/2 Mouse
$"Externa l FDD
$"System O/S
a nd
$"4 x Seria l
Softwa re
Ports
Insta lla tion
$"Pa ra llel Port
The PANEL PC 1000 has a Pentium III little board with a free PCI/ISA
slot inside. It already builds in a Pentium III CPU, relevant DRAM and
a 2.5” HDD. These are all standard and the system is ready to play.
System performance can be increased by upgrading to a higher
performance CPU, higher capacity DRAM modules and hard disk
drive. The user can use the I/O ports located at the back side of the
chassis to connect external peripheral devices, such as a monitor,
serial devices, parallel printer…etc.
NOTE:
Make sure the powe r c ord is disc onne c te d be fore any
installation. To install any inte rnal devic e suc h as C PU,
DRAM and HDD, take out the re ar c hassis c ove r first.
System Installation
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
3.1 CPU
The standard PANEL PC 1000 system already builds in Pentium
III-level CPU. When upgrading to a new CPU of the same level, follow
the instructions below;
1. To remove the existing C PU requires the use of a c hip
puller.
2. Loc a te pin 1 a t the c orner of the C PU soc ket a nd a lign
the C PU’s pin 1 with the pin 1 on the soc ket.
3. Pla c e the C PU in the soc ket. If the insertion of the C PU to
the soc ket is not ea sy, then c hec k whether the notc h on
the c orner of the C PU a nd the notc h on the soc ket a re
properly a ligned.
4. When a new C PU is insta lled, other settings on the system
c ontrol boa rd inc luding C PU type, C PU bus c loc k a nd
C PU volta ge ma y need to be a djusted. Ma ke sure a ll the
settings a re c orrec t for the insta lled C PU. (See the C PU
jumper settings in the C PU c a rd User’s Ma nua l tha t c a me
with the PANEL PC pa c ka ging).
3.2 DRAM
The system control board provides 1 x 168-pin DIMM sockets
supporting system memory up to 256MB.
To install the memory module;
1. Disc onnec t a ll power sourc es.
2. The memory module c a n only fit into the soc ket one wa y.
Holding the memory module with the notc h on the upper
right c orner, then insert the memory module a t a 45°
Angle a nd push the module upright until it c lic ks into
pla c e.
The system auto detects the new memory size and it is not necessary
to change the system configuration after installation.
System Installation
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
3.3 HDD
The standard PANEL PC 1000 already builds in a 2.5” hard disk drive.
If the user intends to remove the existing device for repair or for a
higher-capacity one, then follow the installation instructions below.
1. Ta ke out the sc rews a nd remove the HDD bra c ket.
Mounting orienta tion of the HDD bra c kets on PANEL PC
1000 a re not simila r to ea c h other. The four sc rews
mounting the PANEL PC 1000 HDD bra c ket sits a t the
bottom of the bra c ket.
2. Reinsta ll the new ha rd disk driver to the HDD bra c ket a nd
sc rew the HDD bra c ket to the system c ompa rtment a ga in.
The four rubber sta nds a c t a s c ushions to lessen the
vibra tion tha t usua lly c a uses da ma ge to mec ha nic a l
devic es like a ha rd disk driver.
3. Use the IDE c a ble to c onnec t the HDD to the IDE pin
c onnec tor. Ma tc h pin 1 of the HDD a nd the pin 1 of the
c a ble.
System Installation
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
3.4 4 x Serial Ports
The PANEL PC 1000 provides four onboard serial ports installed on
the bottom rear side of the chassis. Arrangements on PANEL PC
1000 specify COM1, COM2, COM3 providing RS-232 interface, and
with its RS-422/485 interface connected to COM4. Each serial port
comes with +5V/+12V power capabilities on both Pin 1 and Pin 9,
ready to accommodate a wide array of serial devices such as fax
modem, scanner, serial mouse, touch screen...etc. If the touch
screen option is included, its controller will share COM3.
COM1 to COM4 are all D-SUB 9-pin connectors. To attach to any
serial device, just plug in the device connector to the 9-pin D-SUB. In
terms of transmission distance, the RS-422/485 will perform better
than RS-232. In this case, the COM2 is suggested to be set to
RS-422/485 and the related jumpers have to be set correctly first (see
the system board User’s Manual). The RS-485 pin assignment is
listed below.
Signal Name
Pin #
R2-422
RS-485
1
2
3
4
5
6
7
8
9
TX-
DATA-
DATA+
No connector
No connector
GND
TX+
RX+
RX-
1
2
3
4
5
6
7
8
9
GND
No connector No connector
No connector No connector
No connector No connector
No connector No connector
System Installation
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
3.5 Parallel Port
The printer interface is a 25-pin D-SUB connector. To connect any
parallel device, just plug in the device connector to the 25-pin D-SUB.
3.6 VGA
The PANEL PC 1000 has an analog RGB interface connector. It is
able to connect to an expansion CRT monitor, and the system can
display on both the flat panel and the CRT simultaneously.
3.7 Ethernet
The PANEL PC 1000 provides an NE2000 compatible Ethernet
(RJ-45) interface. For network connection, just plug in one cable end
of the PANEL PC 1000 100-Base-T Hub into the standard Ethernet
phone jack. The pin assignment of the RJ-45 is listed below;
RJ-45 Connector Pin Assignment
Pin
Description
8
1
2
3
4
5
6
7
1
2
3
6
Tx+ (Data transmission positive)
Tx- (Data transmission negative)
Rx+(Data reception positive)
Rx- (Data reception negative)
others Not use
RJ-45
System Installation
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
3.8 Digital I/Os
The PANEL PC 1000 provides a digital I/O of 4-channel inputs/outputs
for simple automation control. For example, it can be used to control
the opening and closing of the cash drawer on a POS system. It can
also be used for UPS control. It comes with a 15-pin D-SUB connector,
and its pin position and pin assignment is shown on the following
page.
Digital I/O Pin Assignment
P1
P2
P3
P4
P5
P6
P7
P8
OUT 1
OUT 2
OUT 3
OUT4
GND
P9
GND
P10 GND
P11 IN1
P12 IN2
P13 IN3
P14 IN4
P15 GND
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15
GND
GND
GND
3.9 Keyboard
The PANEL PC 1000 provides a standard PS/2 keyboard connector. If
the user would like to use AT keyboard interface, a conversion cable
is also provided to make this connection.
3.10 PS/2 Mouse
The PANEL PC 1000 has one PS/2 mouse connector. A simple
plug-in will make the connection.
System Installation
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
3.11 External FDD
The PANEL PC 1000 does not build in any floppy disk drive into the
main system. Rather, it provides a FDD interface. An external FDD
cable is provided to connect a standard 3.5” FDD to the system for
system O/S and application software installation. The pin positions
and pin assignments are listed on the next page.
NOTE:
An optional e xte rnal FDD is available for the
PANEL1000-370 syste m. C onsult your authorize d de ale rs or
sale s re pre se ntative s for more information.
PANEL PC 1000
External FDD Pin Assignment
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
P 1
P 2
SIDE1-
RDATA-
GND
P 14
P 15
P 16
P 17
P 18
P 19
P 20
P 21
P 22
P 23
P 24
P 25
P 26
WPT-
TRK0-
GND
10
9
8
P 3
7
6
P 4
GND
WGATE-
GND
5
P 5
GND
4
P 6
WDATA-
REDWC-
NC
NC
3
2
P 7
STEP-
DIR-
1
P 8
P 9
NC
MOTE0-
NC
P 10
P 11
P 12
P 13
DRVS0-
VCC +5V
VCC
DSKCHG-
NC
INDEX-
VCC
System Installation
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
3.12 Expansion Slot
The PANEL PC 1000, this comes as a standard system feature. If the
system comes with expansion capability, then the system includes a
PCI/ISA expansion riser card to accommodate either an ISA or PCI
device at a given time. Due to the internal space limitation, only a
half-size expansion card can be adapted. To use the ISA or PCI
expansion, refer to the following figure and follow the installation
instructions below;
1. Plug the riser c a rd into the onboa rd PC I/ISA slot first.
2. Sc rew the meta l opening to the power supply bra c ket
a nd the multi-I/O c onversion meta l piec e.
3. Plug either a n ISA or PC I c a rd into the ISA or PC I slot on the
riser c a rd a nd sc rew the expa nsion c a rd to the meta l
opening piec e. All the c onnec tors of the expa nsion c a rd
will c ome out from the opening on the rea r c over for
further c a ble c onnec tion.
4. Sc rew the rea r c over to the c ha ssis.
Please also note that the total height of the system with expansion
slot is 93 mm.
16
System Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
3.13 System O/S and Software Installation
The PANEL PC 1000 is not equipped with any operating system. It
builds in a 2.5” HDD and 1.5MB Solid State Disk as memory storage
device. As both devices are built in the system chassis, to load any
O/S or application software into the computer, an external device is
needed to act as a bridge. There are three major ways to load
software into the system.
1. Use an external FDD: Atta c h a 3.5” FDD to the externa l
FDD port via the provided externa l FDD c a ble.26-pin FDD
c onnec tor must be plugged into the system FDD
c onnec tor; the 34-pin sta nda rd 3.5” FDD signa l c onnec tor
a nd the 4-pin FDD power c onnec tor a re c onnec ted to the
sta nda rd 3.5” FDD. Then, c onfigure the system BIOS setup
a nd insert a 3.5” disk c onta ining nec essa ry softwa re a nd
sta rt the insta lla tion.
2. Use Ethernet: If the Ethernet BOOTROM is a lrea dy inc luded
in the system, the user c a n boot up the system via
BOOTROM a nd downloa d system O/S or a pplic a tion
softwa re from the net.
3. Use External CD-ROM/ HDD: When using a n externa l
C D-ROM or HDD for softwa re insta lla tion on P PANEL PC
1000 a n optiona l P-IDE devic e is needed. The P-IDE devic e
is a c onverter to c onvert the pa ra llel port to the IDE
interfa c e.
System Installation
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
This page does not contain any information.
18
System Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
A p p e n d i x A
Power Supply Specifications
Standard AC Power Supplies
PANEL PC 1000 Power Supply
The power supply used in the PANEL PC 1000 is a 100W open frame
power supply. The specifications and features of this special power
supply are listed in the following sections.
Specifications
$"High e ffic ie nc y 100W output
$"Unive rsa l input 100 to 240 VAC
$"O ve r-volta ge prote c tion
$"Sma ll size 3” X 5” footprint
$"C ontinuous short c irc uit prote c tion
$"C onduc tive EMI me e ts FC C c la ss B
Output Specifications
$"Volta ge Ac c ura c y
%"+ 5VDC primary output: + 5%
%"Auxiliary output: + 5%
$"Tota l output power
%"Convection cooled: 100W
%"Forced air cooling: 125W @ 25CFM
$"Hold-up time : 50ms type .
$"O ve r-volta ge prote c tion: a pprox. 5.8V
$"Short c irc uit prote c tion: C ontinuous
$"Ripple a nd noise : 1% pe a k ~ pe a k ma x.
Input Specifications
$"Input volta ge ra nge : 100~240 VAC
$"Inrush c urre nt: 2.4A a t 100VAC or 30A a t 240VAC (c old sta rt)
$"Input fre que nc y: 47~63 Hz
$"Line re gula tion:+ 1%
Power Supply Specifications
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
General Specifications
$"Effic ie nc y: 86% typ.
Environmental Specifications
$"O pe ra ting te mpe ra ture ra nge : 0°C to 40°C
$"Stora ge te mpe ra ture ra nge -40°C to +85°C
$"Humidity, non-c onde nsing: 5% ~ 95%
$"Altitude : 0 to 10,000 fe e t
International Standards
Safety Standards
$"De signe d to me e t the following sta nda rds:
UL 1950, C SA 22.2 NO . 234, VDE EN 60 950
EMI Standards
$"De signe d to me e t the following limits:
FC C doc ke t 20780 c urve “ B”, EN55022 “ B”
CE Standards
$"De signe d to me e t the following sta nda rds:
IEC-801-2 Level 3
IEC-801-3 Level 3
IEC-801-4 Level 3
IEC-801-5 Level 3
8KV air discharge
3V/ M
2KV
2KV
Power Supply Specifications
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
Optional DC Power Supplies
(I) +12V DC Power Supply
Input Specifications
$"Input volta ge ra nge : +9VDC to +18VDC
$"Input c urre nt: 10A a t +12VDC ma x.
Output Specifications
$"Loa d Ra nge :
Min. Load
Voltage Accuracy
Output
Rated Load
+5V
+12V
-12V
0A
0A
0A
10A
1.5A (open)
0.3A
4.95V to 5.05V
11.4V to12.6V
-11.4V to –12.6V
The output ra nge of +12V, -12V a nd down with +5V se tting.
At fa c tory, a ll outputs in 60% ra te d loa d c onditions, the
+5V output is se t to be twe e n 4.95V a nd 5.05V, a nd the
othe r outputs a re c he c ke d to be within the spe c ifie d
volta ge a c c ura c y ra nge .
$"Ripple a nd Noise :
The pe a k-to-pe a k ripple a nd noise for +5V output is le ss
tha n 50mV a nd le ss tha n 100mV for +/-12V outputs, both a t
ra te d loa ds. Me a suring is done by 15MHz ba ndwidth
limite d osc illosc ope a nd te rmina te d e a c h output with
0.47uF c a pa c itor.
$"Line Re gula tion:
The line re gula tion for +5V output is le ss tha n +/-1%, for 12V
is le ss tha n +/-2%, for –12V is le ss tha n +/-3% while
me a suring a t ra te d loa ding a nd +/-10% of input volta ge
c ha nging.
$"Loa d Re gula tion:
The loa d re gula tion for +5V, +12Va re le ss tha n +/-3%, for
-12V is le ss tha n +/-5%, me a suring is done by c ha nging the
me a sure d output loa ding +/-40% from 60% ra te d loa d, a nd
ke e p othe r output a t 60% ra te d loa d.
Power Supply Specifications
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
General Features
$"Effic ie nc y:
The e ffic ie nc y is 70% typic a l while me a suring a t nomina l
line a nd ra te d loa d.
$"Prote c tion:
For some re a son the powe r supply fa ils to c ontrol itse lf, the
built-in ove r-volta ge prote c tion c irc uit will shut down the
outputs to pre ve nt da ma ge to e xte rna l c irc uits. The trip
point of c rowba r c irc uit is a round 5.7V to 7.0V. The powe r
supply will go into la tc h-off mode a ga inst short c irc uit or
ove r loa d c onditions, a nd ha ve to turn O FF a nd the n O N
the DC input to re sta rt the powe r supply.
Environmental Specifications
$"O pe ra ting te mp. ra nge : 0°C to 50°C with forc e d a ir 20c fm
$"Stora ge te mpe ra ture ra nge : -40°C to +85°C
International Standards
Safety Standards
$"De signe d to me e t the following sta nda rds:
UL 1950, C SA 22.2 NO . 234, TUV/LVD EN60 950
EMI Standards
$"De signe d to me e t the following limits::
FC C doc ke t 20780 c urve “ B”, EN55022 “ B”
Power Supply Specifications
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
(II) +24V DC Power Supply
Input Specifications
$"Input volta ge ra nge : +18VDC to +36VDC
$"Input c urre nt: 5A a t +24VDC ma x.
Output Specifications
$"Loa d Ra nge :
Min. Load
Voltage Accuracy
Output
Rated Load
+5V
+12V
-12V
0A
0A
0A
10A
1.5A (open)
0.3A
4.95V to 5.05V
11.4V to12.6V
-11.4V to –12.6V
The output ra nge of +12V, -12V a nd down with +5V se tting.
At fa c tory, a ll outputs in 60% ra te d loa d c onditions, the
+5V output is se t to be twe e n 4.95V a nd 5.05V, a nd the
othe r outputs a re c he c ke d to be within the spe c ifie d
volta ge a c c ura c y ra nge .
$"Ripple a nd Noise :
The pe a k-to-pe a k ripple a nd noise for +5V output is le ss
tha n 50mV a nd le ss tha n 100mV for +/-12V outputs.
Me a suring is done by 15MHz ba ndwidth limite d
osc illosc ope a nd te rmina te d e a c h output with 0.47uF
c a pa c itor.
$"Line Re gula tion:
The line re gula tion for +5V output is le ss tha n +/-1%, for
+12V is le ss tha n +/-2%, for –12V is le ss tha n +/-3% while
me a suring a t ra te d loa ding a nd +/-10% of input volta ge
c ha nging.
$"Loa d Re gula tion:
The loa d re gula tion for +5V is le ss tha n +/-3%, for +12V is
le ss tha n +/-5%, -12V is le ss tha n +7% -3%, me a suring is
done by c ha nging the me a sure d output loa ding +/-40%
from 60% ra te d loa d, a nd ke e p othe r output a t 60% ra te d
loa d.
Power Supply Specifications
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
General Features
$"Effic ie nc y:
The e ffic ie nc y is 75% typic a l while me a suring a t nomina l
line a nd ra te d loa d.
$"Prote c tion:
For some re a son the powe r supply fa ils to c ontrol itse lf, the
built-in ove rvolta ge prote c tion c irc uit will shut down the
outputs to pre ve nt da ma ge to e xte rna l c irc uits. The trip
point of c rowba r c irc uit is a round 5.7V to 7.0V. The powe r
supply will go into la tc h-off mode a ga inst short c irc uit or
ove r loa d c onditions, a nd ha ve to turn O FF a nd the n O N
the DC input to re sta rt the powe r supply.
Environmental Specifications
$"O pe ra ting te mp. ra nge : 0°C to 50°C with forc e d a ir 20c fm
$"Stora ge te mpe ra ture ra nge : -40°C to +85°C
International Standards
Safety Standards
$"De signe d to me e t the following sta nda rds:
UL 1950, C SA 22.2 NO . 234, TUV/LVD EN60 950
EMI Standards
$"De signe d to me e t the following limits:
FC C doc ke t 20780 c urve “ B”, EN55022 “ B”
Power Supply Specifications
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL PC 1000 All-in-One PANEL PC User’s Manual
(III) +48V DC Power Supply
Input Specifications
$"Input volta ge ra nge : +36VDC to +72VDC
$"Input c urre nt: 3A a t +48VDC ma x.
Output Specifications
$"Loa d Ra nge :
Min. Load
Voltage Accuracy
Output
Rated Load
+5V
+12V
-12V
0A
0A
0A
10A
1.5A
0.3A
4.95V to 5.05V
11.4V to12.6V
-11.4V to –12.6V
At fa c tory, a ll outputs in 60% ra te d loa d c onditions, the
+5V output is se t to be twe e n 4.95V a nd 5.05V, a nd the
othe r outputs a re c he c ke d to be within the spe c ifie d
volta ge a c c ura c y ra nge .
$"Ripple a nd Noise :
The pe a k-to-pe a k ripple a nd noise for +5V output is le ss
tha n 60mV a nd le ss tha n 100mV for +/-12V outputs.
Me a suring is done by 15MHz ba ndwidth limite d
osc illosc ope a nd te rmina te d e a c h output with 0.47uF
c a pa c itor.
$"Line Re gula tion:
The line re gula tion for +5V output is le ss tha n +/-1%, for
+12V is le ss tha n +/-2%, for –12V is le ss tha n +/-3% while
me a suring a t ra te d loa ding a nd +/-10% of input volta ge
c ha nging.
$"Loa d Re gula tion:
The loa d re gula tion for +5V is le ss tha n +/-3%, for +12V is
le ss tha n +/-5%, -12V is le ss tha n +7% -3%, me a suring is
done by c ha nging the me a sure d output loa ding +/-40%
from 60% ra te d loa d, a nd ke e p othe r output a t 60% ra te d
loa d.
Power Supply Specifications
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL1000-370 All-in-One PANEL PC User’s Manual
General Features
$"Effic ie nc y:
The e ffic ie nc y is 75% typic a l while me a suring a t nomina l
line a nd ra te d loa d.
$"Prote c tion:
For some re a son the powe r supply fa ils to c ontrol itse lf, the
built-in ove r-volta ge prote c tion c irc uit will shut down the
outputs to pre ve nt da ma ge to e xte rna l c irc uits. The trip
point of c rowba r c irc uit is a round 5.7V to 7.0V. The powe r
supply will go into la tc h-off mode a ga inst short c irc uit or
ove r loa d c onditions, a nd ha ve to turn O FF a nd the n O N
the DC input to re sta rt the powe r supply.
Environmental Specifications
$"O pe ra ting te mp. ra nge : 0°C to 50°C with forc e d a ir 20c fm
$"Stora ge te mpe ra ture ra nge : -40°C to +85°C
International Standards
Safety Standards
$"De signe d to me e t the following sta nda rds:
UL 1950, C SA 22.2 NO . 234, TUV/LVD EN60 950
EMI Standards
$"De signe d to me e t the following limits:
FC C doc ke t 20780 c urve “ B”, EN55022 “ B”
Power Supply Specifications
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|