MONITOR WITH DVD RECEIVER
KVT-729DVD
INSTALLATION MANUAL
© B54-4516-00/00 (EV)
Installation Procedure
1. To prevent short circuits, remove the key from the
ignition and disconnect the - terminal of the
battery.
2. Make the proper input and output wire
connections for each unit.
¤
•
If the power is not turned ON (or it is ON, but will be OFF
immediately), the speaker wire may have a short-circuit
or touched the chasis of the vehicle and the protection
function may have been activated. Therefore, the speaker
wire should be checked.
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.
5. Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
•
•
•
•
If your car is not prepared for this special connection-
system, consult your Kenwood dealer.
Only use antenna conversion adapters (ISO-JASO) when the
antenna cord has an ISO plug.
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
If the fuse blows, first make sure that the wires have not
caused a short circuit, then replace the old fuse with one
with the same rating.
2WARNING
•
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
Do not cut out the fuse from the ignition wire (red) and the
battery wire (yellow). The power supply must be connected
to the wires via the fuse.
•
•
Insulate unconnected wires with vinyl tape or other similar
material. To prevent short circuits, also do not remove
the caps on the ends of the unconnected wires or the
terminals.
•
•
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may receive damage or fail
to work if you share the - wires and/or ground them to
any metal part in the car.
•
•
After the unit is installed, check whether the brake lamps,
indicators, wipers, etc. on the car are working properly.
If the console has a lid, make sure to install the unit so
that the faceplate does not hit the lid when closing and
opening.
•
Mount the unit so that the mounting angle is 30° or less.
|
English
3
Connection
Monitor/Player unit
Do not connect.
USB device
(commercially available)
USB connector
Accessory !
Wiring harness
(Accessory 2)
Ground wire (Black)
FUSE ( 5A )
Ground wire (Black)
The cable (Accessory 3) is
fixed with a chassis using
harness band (Accessory
!).
Connector A
BATT
Battery wire (Yellow)
Ignition wire (Red)
8
7
6
5
4
3
2
1
ACC
8
7
6
5
4
3
2
1
Accessory 0
(ISO–JASO)
Accessory 4
Connector B
Antenna Cord (ISO)
FUSE ( 10A )
(Orange/White)
Dimmer control wire (Orange/White)
Connect to the vehicle's parking brake
detection switch harness
using the supplied relay connector.
For the sake of safety, be sure to connect the parking sensor.
Parking sensor wire (Light Green)
Reverse sensor wire (Purple/White)
PRK SW
To vehicle's reverse lamp harness
To steering remote
Steering remote control input (Light Blue/Yellow)
Mute wire (Brown)
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
To connect the Kenwood navigation system,
consult your navigation manual.
Power control/ Motor antenna control wire
(Blue/White)
Connect either to the power control terminal when using the optional
power amplifier, or to the antenna control terminal in the vehicle.
External amplifier control wire (Pink/Black)
To "EXT.AMP.CONT." terminal of the amplifier
having the external amp control function.
If no connections are made, do not let the cable come out from the tab.
|
4
KVT-729DVD
Receiver unit
Accessory !
The cable (Accessory 3) is
fixed with a chassis using
harness band (Accessory
!).
Accessory 3
Receiver unit
FM/AM antenna input
Wiring harness
(Accessory 1)
ILLUMI
Ground wire (Black) - (To car chassis)
A
REVERSE
REMO.CONT
MUTE
A
+
ANT CONT P. CONT
EXT. CONT
Battery
If you connect the ignition wire (red) and the battery wire (yellow)
to the car chassis (ground), you may cause a short circuit, that in
turn may start a fire. Always connect those wires to the power
source running through the fuse box.
|
English
5
Connecting Wires to Terminals
Connector Function Guide
Pin Numbers for Cable Colour
ISO Connectors
External Power
Connector
2WARNING
Functions
Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on
the type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
A-4
A-5
A-6
A-7
A-8
Yellow
Battery
Power Control
Dimmer
Ignition (ACC)
Earth (Ground)
Connection
The default connection for the wiring harness is described in
1 below. If the ISO connector pins are set as described in 2
or 3, make the connection as illustrated.
Please be sure to reconnect the cable as shown 2 below to
install this unit to the Volkswagen vehicles etc.
Blue/White
Orange/White
Red
Black
Speaker
Connector
B-1
B-2
B-3
B-4
B-5
B-6
B-7
1(Default setting) The A-7 pin (red) of the vehicle’s
ISO connector is linked with the ignition, and the A-
4 pin (yellow) is connected to the constant power
supply.
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
B-8
Green/Black
2The A-7 pin (red) of the vehicle’s ISO connector is
connected to the constant power supply, and the
A-4 pin (yellow) is linked to the ignition.
A-7 Pin (Red)
Ignition cable
Unit
Vehicle
A-4 Pin (Yellow)
Battery cable
(Yellow)
3The A-4 pin (yellow) of the vehicle’s ISO connector
is not connected to anything, while the A-7 pin
(red) is connected to the constant power supply
(or both the A-7 (red) and A-4 (yellow) pins are
connected to the constant power supply).
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
⁄
•
When the connection is made as in 3 above, the unit’s
power will not be linked to the ignition key. For that reason,
always make sure to turn off the unit’s power when the
ignition is turned off.
To link the unit’s power to the ignition, connect the ignition
cable (ACC...red) to a power source that can be turned on
and off with the ignition key.
|
6
KVT-729DVD
System Connection
Receiver unit
■
■
■
■
Front Preout
• Audio left output (White)
• Audio right output (Red)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
Audio/Visual input
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
■
■
Rear View Camera Input
• Visual input (Yellow)
Audio/Visual Output
• Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
|
English
7
Optional Accessory Connection
iPod
(commercially available)
KCA-iP300V
(Optional Accessory)
Audio Input
Resistance-free stereo type mini
plug (3.5Ф)
Audio Output
(Black)
Visual Input
Resistance-free mini plug (3.5Ф)
Monitor/Player unit
Visual Output
(Yellow)
USB terminal
USB terminal
Receiver unit
Accessory 3
Connection cable
(Included in the Navigation System)
Connection cable
(Included in the Disc changer)
Disc Changer etc.
(Optional Accessory)
Navigation System
(Optional Accessory)
TV Tuner
(Optional Accessory)
T V A N T E N N A I N P U T
R O U N I T
M O O T N I T
Connection cable
(Included in the TV tuner)
|
8
KVT-729DVD
Installation for Monitor/Player Unit
Firewall or metal support
Screw (M4X8)
(commercially available)
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Self-tapping screw
(commercially available)
Metal mounting strap
(commercially available)
Accessory 5
Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).
Installation for Receiver Unit
1. Attach the installation brackets 9 to the sides of
the receiver unit using the sems bolts 7.
Installation brackets
(Accessory 9)
Sems bolts (M4 × 8 mm)
(Accessory 7)
2. Use the tapping screw 8 to secure the receiver
unit to the audio board.
Tapping screw (ø4 × 16 mm)
(Accessory 8)
|
English
9
Removing Monitor/Player Unit
Removing the Hard Rubber Frame
(escutcheon)
1. Engage the catch pins on the removal tool 6 and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in
the figure.
Removing the Unit
1. Remove the hard rubber frame by referring to the
removal procedure in the section <Removing the
Hard Rubber Frame>.
2. Remove the Hex-head screw with integral washer
(M4 × 8) on the back panel.
3. Insert the two removal tools 6 deeply into the
slots on each side, as shown.
Removal Tool (Accessory 6)
Removal Tool
(Accessory 6)
Catch
Lock
⁄
•
The frame can be removed from the top side in the same
manner.
4. Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
2. When the lower level is removed, remove the
upper two locations.
⁄
•
Be careful to avoid injury from the catch pins on the
removal tool.
5. Pull the unit all the way out with your hands, being
careful not to drop it.
|
10
KVT-729DVD
|