MONITOR WITH DVD RECEIVER
KVT-536DVD
KVT-536DVDM
INSTALLATION MANUAL
© B54-4752-00/00 (MW/M2W)
Installation Procedure
•
•
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
This unit has the cooling fan (page 5) to decrease the
internal temperature. Do not mount the unit in a place
where the cooling fan of the unit are blocked. Blocking
these openings will inhibit the cooling of the internal
temperature and result in malfunction.
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
•
•
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
•
•
2CAUTION
•
Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and shortly
after the use of the unit. Metal part such as the heat sink
and enclosure become hot.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
•
•
•
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
•
•
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
|
English
3
Connecting Wires to Terminals
Ignition key
switch
USB device
(commercially available)
USB connector
ACC
Ignition wire (Red)
Battery wire (Yellow)
Car fuse box
Car fuse box
(Main fuse)
If you connect the ignition wire (red) and
the battery wire (yellow) to the car chassis
(ground), you may cause a short circuit, that
in turn may start a fire. Always connect those
wires to the power source running through
the fuse box.
Ground wire (Black)- (To car chassis)
+
–
Battery
FUSE ( 15A )
Connect to the vehicle's parking brake detection
switch harness.
Parking sensor wire (Light Green)
PRK SW
For the sake of safety, be sure to connect the parking sensor.
Reverse sensor wire (Purple/White)
Dimmer control wire (Orange/White)
Connect to vehicle’s reverse lamp harness when
using the optional rear view camera.
To car light control switch
To use the steering wheel remote control feature,
you need to an exclusive remote adapter (not
supplied) matches your car is required.
Steering remote control input (Light Blue/Yellow)
Mute wire (Brown)
To steering remote
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
To connect the Kenwood navigation system,
consult your navigation manual.
Depending on what antenna you are using, connect either to the control
terminal of the motor antenna, or to the power terminal for the booster
amplifier of the film-type or short pole type antenna.
Motor antenna control wire (Blue)
Power control wire (Blue/White)
When using the optional power amplifier,
connect to its power control terminal.
If no connections are made, do not let the cable come out from the tab.
|
4
KVT-536DVD/KVT-536DVDM
Cooling fan
Antenna Cord
FM/AM antenna input
Wiring harness
(Accessory 1)
Audio/Visual input /
Rear View Camera Input
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
AV IN
Wiring harness
(Accessory 2)
REAR VIEW
CAMERA
Audio/Visual Output
• Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
REVERSE
ILLUMI
AV OUT
Rear/Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
REAR/SUB
WOOFER
STEERING WHEEL
REMOTE INPUT
REMOTE CONT
Front Preout
FRONT
• Audio left output (White)
• Audio right output (Red)
MUTE
White/Black
To front left speaker
+
+
White
ANT CONT
P. CONT
Gray/Black
To front right speaker
To rear left speaker
To rear right speaker
Gray
Green/Black
+
+
Green
Purple/Black
Purple
|
English
5
Optional Accessory Connection
iPod
(commercially available)
KCA-iP301V
(Optional Accessory)
Audio Input
Resistance-free stereo type mini
plug (3.5Ф)
Audio Output
(Black)
Visual Input (Yellow)
Resistance-free mini plug (3.5Ф)
Visual Output
(Yellow)
USB terminal
USB terminal
To KCA-BT200
(Optional Accessory)
Connection cable
(Included in the Navigation System)
TV Tuner
(Optional Accessory)
T V A N T E N N A I N P U T
Navigation System
(Optional Accessory)
R O U N I T
M O O T N I T
Connection cable
(Included in the TV tuner)
Navigation units that can be connected to this unit.
(As of December, 2009):
⁄
・ KNA-G630
・ KNA-G630CN
For latest information, access the
|
6
KVT-536DVD/KVT-536DVDM
Installation/Removing the Unit
Installation
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).
|
English
7
Installation/Removing the Unit
Removing the Hard Rubber Frame
(escutcheon)
Removing the Unit
1. Remove the hard rubber frame by referring to the
removal procedure in the section <Removing the
Hard Rubber Frame>.
2. Insert the two removal tools 3 deeply into the
slots on each side, as shown.
1. Engage the catch pins on the removal tool 3 and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in
the figure.
Removal Tool
(Accessory 3)
Escutcheon (Accessory 4)
Removal Tool (Accessory 3)
Catch
Lock
3. Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
⁄
•
The frame can be removed from the top side in the same
manner.
2. When the lower level is removed, remove the
upper two locations.
⁄
•
Be careful to avoid injury from the catch pins on the
removal tool.
4. Pull the unit all the way out with your hands, being
careful not to drop it.
|
8
KVT-536DVD/KVT-536DVDM
Installing in Japanese-made Cars
Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by "●"
or
Accessory 5 (M5x6mm)
or Accessory 6 (M5x7mm)
Car Bracket
Accessory 5 (M5x6mm)
or Accessory 6 (M5x7mm)
Screws (included in
audio unit package)
Screws (included in
audio unit package)
Audio unit or others
⁄
•
Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage
the unit.
|
English
9
Installing in Japanese-made Cars
Installation on Toyota Car using Brackets at Holes shown by "●"
or
When using the bracket shown above, you cannot use screws at two holes of
the right and left unit sides.
1. Mount the bracket at each side.
Car Bracket
Accessory 5 (M5x6mm)
Accessory 5 (M5x6mm)
Screws (included in
audio unit package)
Screws (included in
audio unit package)
2. Bend each end of case to fix the bracket.
Use a flat-blade screwdriver or pliers, and bend
each case tab into the hole of installation
bracket to fix the bracket.
|
10
KVT-536DVD/KVT-536DVDM
|