DVD Receiver
DSR-4.8
Instruction Manual
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may
rise, shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject
to vibrations from loudspeakers. Never put the
unit on top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its
side or on a sloping surface, because it may cause
a malfunction.
• If you install this unit near a TV, radio, or VCR,
the picture and sound quality may be affected. If
this occurs, move this unit away from the TV,
radio, or VCR.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
the dealer from whom you purchased this unit.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild deter-
gent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thin-
ners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel let-
tering.
8. To Obtain a Clear Picture—This unit is a high-
tech, precision device. If the lens on the optical
pickup, or the disc drive mechanism becomes dirty
or worn, the picture quality may be affected. To
maintain the best picture quality, we recommend
regular inspection and maintenance (cleaning or
worn part replacement) every 1,000 hours of use
depending on the operating environment. Contact
the dealer from whom you purchased this unit for
details.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the unit’s rear panel (e.g., AC 230
V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit from
the AC power source. Make sure that the plug is readily
operable (easily accessible) at all times.
9. Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
Pressing the [Standby/On] button to select Standby mode
does not fully shutdown the unit. If you do not intend to
use the unit for an extended period, remove the power cord
from the AC outlet.
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
• Moisture condensation can occur in the following
situations:
– The unit is moved from a cold place to a warm
place.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
– In the summer, when this unit is moved from
an air conditioned room to a hot and humid
place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility
of moisture condensation occurring. Doing so
may damage your discs and certain parts inside
this unit.
If condensation does occur, remove all discs and
leave this unit turned on for two to three hours. By
this time, the unit will have warmed up and any con-
densation will have evaporated.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by the dealer from
whom you purchased this unit.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
• When you’ve finished using this unit, remove all
discs and turn off the power.
7. Installing this Unit
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an
audio rack. If the ventilation is inadequate, the
unit may overheat, leading to malfunction.
3
Precautions—Continued
10. Region Numbers—The DVD standard uses region
numbers to control how discs can be played around
the world, the world being divided into six regions.
This unit will only play DVD discs that match its
region number, which can be found on its rear panel
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
ALL
1
(e.g.,
,
).
11. About this Manual—This manual explains how to
use all of this unit’s functions. Although the DVD
standard offers many special features, not all discs
use them all, so depending on the disc being played,
this unit may not respond to certain functions. See
the disc’s sleeve notes for supported features.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to
use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
To prevent being exposed to the laser beam, do not try to
open the enclosure.
CAUTION:
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
THIS PRODUCT UTILIZES A LASER. USE OF CON-
TROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECI-
FIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
The label on the right is
applied on the rear panel.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
1. This unit is a CLASS 1
LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not
remove the cover. Refer servicing to qualified person-
nel.
Modèle canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
4
Thank you for purchasing an Integra DVD receiver.
Read this manual carefully before using your new DVD
receiver. A good understanding of its features and oper-
ation will allow you to achieve optimum performance
and enjoyment.
Supplied Accessories
Make sure you have the following accessories:
RC-705S
Keep this manual for future reference.
Remote controller & 2 batteries (AA/R6)
Video cable (RCA) (1.5 m)
Indoor FM antenna
AM loop antenna
Power cord
* In catalogs and on packaging, the letter at the end of
the product name indicates the color. Specifications
and operations are the same regardless of color.
5
Introduction
Features
Highlights
*1
*1
*2
• Dolby Digital, DTS
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of
Dolby Laboratories.
• DVD-Video, Video CD, audio CD
• MP3, WMA , JPEG
*3
*2
• DVD-Audio and Super Audio CD
• CD-R/RW, DVD-R/RW, and DVD+R/RW com-
patible
“DTS” is a registered trademark of DTS, Inc. and “96/24” is a
trademark of DTS, Inc.
*4
• HDMI digital interface
*3
Video
• HDMI Pass-Thru
(1080p Compatible; 1 Input/1 Output)
• HDTV-Capable (50 MHz)
Windows Media, and the Windows logo are trademarks, or reg-
istered trademarks of Microsoft Corporation in the United
States and/or other countries.
• JPEG in High Definition
*4
• Advanced 108 MHz/14-bit video D/A converter
• 2 Composite Video Inputs
HDMI, the HDMI logo and High-Definition Multimedia Inter-
face are trademarks or registered trademarks of HDMI licens-
ing LLC.
• Component and composite video outputs
• Repeat/A-B Repeat/Random/Memory playback
• Supports 4:3 and 16:9 aspect ratio TVs
• Three view modes providing a best-fit picture regard-
less of TV aspects
• Picture Zoom Function
• Parental Lock function
• Screen Saver function
*5 “Theater-Dimensional” is a trademark of Onkyo Corporation.
*
*
*
“Xantech” is a registered trademark of Xantech Corporation.
“Niles” is a registered trademark of Niles Audio Corporation.
Apple and iPod are trademarks of Apple, Inc., registered in the
U.S. and other countries.
This product incorporates copyright protection technology that
is protected by U.S. patents and other intellectual property
rights. Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended for
home and other limited consumer uses only unless otherwise
authorized by Macrovision. Reverse engineering or disassem-
bly is prohibited.
Audio
• 192 kHz/24-bit D/A converter
• 2 Digital Inputs (1 Optical/1 Coaxial)
*5
• Theater-Dimensional Virtual Surround
• Direct Mode
• Dynamic Range Control setting
Others
• Compatible with RI Dock for iPod
• A/V Sync Control Function (up to 100 ms)
• 40 AM/FM Presets
• IR Input and Output
• RS232 Port for Interface Control
• 1/4-inch phone jack
• Aluminum Front Panel, Volume and Input Selector
Knob
• Adjustable display brightness
6
Contents
Overview
Playback Techniques
Important Safety Instructions .................................... 2
Precautions ............................................................... 3
Supplied Accessories................................................ 5
Introduction ............................................................... 6
Features ................................................................ 6
Disc Notes............................................................. 8
Before Using the DVD receiver............................... 11
Installing the Batteries......................................... 11
Using the Remote Controller............................... 11
Front & Rear Panels................................................ 12
Front Panel.......................................................... 12
Display................................................................. 13
Rear Panel .......................................................... 14
Remote Controller ............................................... 15
Advanced Playback................................................. 43
Selecting Chapters/Titles/Tracks/Folders by
Number ............................................................. 43
Searching by Time............................................... 44
Repeat Playback ................................................. 45
A-B Repeat Playback .......................................... 45
Random Playback ............................................... 46
Memory Playback................................................ 47
Last Memory........................................................ 48
Zooming............................................................... 49
Selecting Camera Angles.................................... 49
Selecting Soundtracks......................................... 50
Selecting Subtitles............................................... 50
Advanced Operations
Connections
Disc and Input Information ...................................... 51
Displaying Information......................................... 51
Controlling Other Components................................ 52
Controlling a TV connected
to the DVD receiver........................................... 52
Controlling an Apple iPod in RI Dock
Connecting the DVD receiver.................................. 17
Placing the Speakers .......................................... 17
Connecting Your Speakers ................................. 17
Connecting Antenna............................................ 18
AV Cables & Connectors..................................... 21
Video Output/Video Setting Matrix ...................... 22
Video Signal Flow Chart...................................... 22
Before Making Any Connections......................... 23
Basic Setup......................................................... 23
Connecting Your TV (video connection).............. 24
Connecting Other AV Component....................... 24
Connecting an RI Dock ....................................... 25
Digital Audio Connection..................................... 25
Connecting your HDTV or AV component
connected to the DVD receiver......................... 53
Detailed Settings
Configuring the DVD receiver.................................. 54
Setup Menu ......................................................... 54
DVD Onscreen Setup Menus.................................. 57
Using the Onscreen Setup Menus....................... 58
Picture Menu ....................................................... 59
Audio Menu ......................................................... 61
Language Menu................................................... 61
Display Menu....................................................... 63
Operation Setting Menu....................................... 64
with an HDMI connection.................................. 26
Using the Multiroom Control Kits......................... 27
Connecting the Power/Turning
on the DVD receiver ............................................. 28
Getting Started and Setting up
Miscellaneous information
Initial Setup ............................................................. 29
First Time Setup.................................................. 29
HDMI and Progressive Settings.............................. 30
Setting the HDMI................................................. 30
Selecting Progressive or Interlaced..................... 30
Additional information.............................................. 66
Resetting the receiver.......................................... 66
DVD-Video regions.............................................. 66
Disc Content Organization................................... 66
Glossary .................................................................. 67
Troubleshooting....................................................... 69
Power .................................................................. 69
Audio ................................................................... 69
Video ................................................................... 70
Tuner ................................................................... 71
Remote Controller ............................................... 71
Disc Playback...................................................... 71
Connection with External Devices....................... 72
HDMI Status Mode .............................................. 73
Specifications .......................................................... 74
Basic Operations
Understanding Common Operations....................... 31
Adjusting the Volume .......................................... 31
Selecting the Input Source .................................. 31
Using Headphones.............................................. 31
Muting the DVD receiver ..................................... 32
Using the Sleep Timer......................................... 32
Adjusting Subwoofer Level.................................. 32
Playing Discs........................................................... 33
Starting, Pausing & Stopping Playback............... 33
Select Next & Previous track/chapter.................. 34
Fast Forward & Reverse ..................................... 35
Forward Frame-by-Frame Playback.................... 35
Navigating DVD & VCD Disc Menus................... 36
Navigating CDs & Super Audio CDs ................... 36
Navigating MP3 & WMA Discs............................ 37
Viewing a Slideshow of JPEG Images ................ 38
Listening to the Radio ............................................. 39
Using the Tuner................................................... 39
Presetting AM/FM Stations.................................. 40
Using the Listening Modes...................................... 41
Selecting Listening Modes .................................. 41
About the Listening Modes.................................. 41
Remote Control Codes List
The end of this manual
7
Introduction—Continued
• The DVD receiver does not support disc types not
listed.
Disc Notes
• The DVD receiver supports 8 cm and 12 cm discs.
• Don’t use discs with an unusual shape, such as those
shown below, because you may damage the DVD
receiver.
Supported Discs
The DVD receiver supports the following discs.
Disc
Logo
Format or file type
*1
DVD-Video
DVD-Audio
DVD-Audio
• Don’t use discs that have residue from adhesive tape,
rental discs with peeling labels, or discs with custom-
made labels or stickers. Doing so may damage the
DVD receiver and you may not be able to remove the
disc properly.
Super Audio
CD
Super Audio CD (single
layer, dual layer, hybrid)
DVD-Video, MP3, WMA,
JPEG
DVD-R*2
About playing copy-controlled CDs
DVD-Video, MP3, WMA,
JPEG
Some copy-controlled CDs may not conform to official
CD standards. They are special discs and may not play
on the DVD receiver.
DVD-RW*2
Video CD
Including PBC
PCM
Function Support
The following icons are used throughout this manual to
indicate which functions can be used with the various
disc formats and file types.
Audio CD*3
CD-R*2
Audio CD, MP3, WMA,
JPEG
Icon
Disc format or file type
DVD-V
DVD-Video
Audio CD, MP3, WMA,
JPEG
CD-RW*2
DVD-A
SACD
VCD
CD
DVD-Audio
Super Audio CD
Video CD
JPEG CD
JPEG
– DVD+R/RW –
The DVD receiver supports DVD+R/RW discs
recorded in the following formats:
Audio CD
• Discs recorded in DVD-Video mode.
• Discs recorded in ISO 9660 Level 2 or Joliet
format containing MP3, WMA, or JPEG files.
MP3
WMA
JPEG
MP3 file
WMA file
*1 The DVD receiver’s region number is printed on the rear panel.
If you attempt to play a disc intended for another region, the
message appears onscreen.
JPEG file
*2 MP3, WMA, and JPEG files are supported on discs recorded in
ISO 9660 Level 2 or Joliet format. (See “MP3/WMA/JPEG
Compatibility” on page 9 for more details.) However, some
CD-R, CD-RW, DVD-R, and DVD-RW discs may not work
properly for any of the following reasons: incomplete disc
finalization, disc burner characteristics, disc characteristics, the
disc is damaged or dirty, the disc contains only a small amount
of data. Discs that contain different types of files, JPEG, MP3,
WMA, and so on, are not supported. See the manual supplied
with your disc burner for more information. Condensation or
dirt on the optical pickup lens can also affect playback.
*3 Some audio CDs feature copy protection that doesn’t conform
to the official CD standard. Since these are nonstandard discs,
they may not play properly in the DVD receiver.
About this Manual
This manual explains how to use all of the DVD
receiver’s functions. Although the DVD standard offers
many special features, not all discs use them all, so
depending on the disc being played, the DVD receiver
may not respond to certain functions. See your disc’s
sleeve notes for supported features.
When you attempt to use a DVD feature that is
not available, this logo may appear onscreen,
indicating that the feature is not supported by
the current disc or by the DVD receiver.
8
Introduction—Continued
MP3/WMA/JPEG Compatibility
About WMA
• The DVD receiver can play/display MP3, WMA, and
JPEG files recorded on CD-R, CD-RW, DVD-R,
DVD-RW, DVD+R and DVD+RW discs.
• Discs must be in ISO 9660 Level 2 or Joliet format
(folders can be up to eight levels deep). Music files
recorded on discs that use the HFS (hierarchical file
system) cannot be played.
• Discs must be finalized.
• The DVD receiver can only recognize the first session
on multisession discs.
WMA is an acronym for Windows Media Audio and
refers to an audio compression technology developed by
Microsoft Corporation. WMA content can be encoded
®
by using Windows Media Player version 7/7.1 or 8.
Handling Discs
• Never touch the underside of a disc. Always hold discs
by the edge, as shown.
• You can determine the order in which the DVD
receiver plays/displays your MP3/WMA songs and
JPEG pictures by prefixing file and folder names with
a three-digit number. For example 001.Root,
002.Folder, and so on, and 001.Track.mp3,
002.Track.mp3, and so on.
Underside
• Never attach adhesive tape or sticky labels to discs.
•
Only the first eight characters of folder and track names
(excluding the filename extension) are displayed.
• The folder numbered “001” appears as “ROOT” in the
Disc Navigator.
• The DVD receiver supports up to 255 folders and up
to 255 files per folder.
• If you try to play an incompatible file, the message
“This format cannot be played.” appears on the dis-
play.
Cleaning Discs
• For best results, keep your discs clean. Fingerprints
and dust can affect the sound and picture quality and
should be removed as follows. Using a clean soft
cloth, wipe from the center outwards, as shown. Never
wipe in a circular direction.
■ MP3
• MP3 files must be MPEG1 Audio Layer 3 format,
44.1 or 48 kHz, fixed bit-rate.
• MP3 files must have a “.mp3” or “.MP3” filename
extension.
• Variable bit-rates (VBR) from 32 kbps to 320 kbps are
supported. (Playing times may display incorrectly
with VBR.)
✔
■ WMA
• WMA files must have the copyright option turned off.
• Sampling rates 44.1/48 kHz are supported.
• Variable bit-rates (VBR) from 48 kbps to 192 kbps
(44.1 kHz) and 128 kbps to 192 kbps (48 kHz) are
supported. (Playing times may display incorrectly
with VBR.)
• To remove stubborn dust or dirt, wipe the disc with a
damp soft cloth, and then dry it with a dry cloth.
• Never use solvent-based cleaning fluids, such as thin-
ner or benzine, commercially available cleaners, or
antistatic sprays intended for vinyl records, because
they may damage the disc.
• WMA files must have a “.wma” or “.WMA” filename
extension.
Storing Discs
■ JPEG
• JPEG files must have a “.jpg” or “.JPG” filename
extension.
• JPEG files must be less than 5 megabytes in size.
• JPEG files up to 5,700 x 3,800 pixels are supported.
• Don’t store discs in places subject to direct sunlight, or
near heat sources.
• Don’t store discs in places subject to moisture or dust,
such as in a bathroom or near a humidifier.
• Always store discs in their cases and vertically. Stack-
ing, or putting objects on unprotected discs may cause
warping, scratches, or other damage.
9
Introduction—Continued
Copyright
It is forbidden by law to copy, broadcast, show, broad-
cast on cable, play in public, or rent copyrighted material
without permission.
DVD-Video discs are copy-protected, and any record-
ings made from these discs will be distorted.
This product incorporates copyright protection technol-
ogy that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use
of this copyright-protection technology must be autho-
rized by Macrovision Corporation, and is intended for
home and other limited viewing uses only, unless other-
wise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
10
Before Using the DVD receiver
Installing the Batteries
Using the Remote Controller
To use the remote controller, point it at the DVD
receiver’s remote control sensor, as shown below.
To open the battery compartment, press
the small hollow and slide off the cover.
1
Remote control sensor
DVD receiver
Approx. 16 ft.
(5 m)
Insert the two supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
2
Notes:
• The remote controller may not work reliably if the
DVD receiver is subjected to bright light, such as
direct sunlight or inverter-type fluorescent lights.
Keep this in mind when installing the DVD receiver.
• If another remote controller of the same type is used in
the same room, or the DVD receiver is installed close
to equipment that uses infrared rays, the remote con-
troller may not work reliably.
• Don’t put anything, such as a book, on the remote con-
troller, because the buttons may be pressed inadvert-
ently, thereby draining the batteries.
• The remote controller may not work reliably if the
DVD receiver is installed in a rack behind colored
glass doors. Keep this in mind when installing the
DVD receiver.
Put the cover onto the remote controller
and slide it shut.
3
• The remote controller will not work if there’s an
obstacle between it and the DVD receiver’s remote
control sensor.
Notes:
• If the remote controller doesn’t work reliably, try
replacing both batteries.
• Don’t mix new and old batteries, or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent possible leakage
and corrosion.
• Flat batteries should be removed as soon as possible to
prevent possible leakage and corrosion.
11
Front & Rear Panels
For detailed information, refer to the pages in brackets.
Front Panel
ꢂꢀ ꢁ
ꢃ
ꢄ ꢅ ꢆ
ꢇ
ꢊ
ꢋ ꢈ
ꢌ
ꢉ
ꢍ
ꢀ Standby/On button [28]
ꢈꢌ Previous/Next
/
buttons or Tuning/
This button is used to set the DVD receiver to On or
Standby.
Preset
The Previous [
/
buttons [34, 39]
] button is used to select the pre-
vious chapter or track. During playback it selects
the beginning of the current track.
ꢁ Standby indicator [28]
This indicator lights up when the DVD receiver is in
Standby.
The Next [
] button is used to select the next
chapter or track.
ꢂ Input selector [31] and indicator
This selector is used to select from the following
input sources: DVD, VIDEO 1, VIDEO 2/DOCK,
FM, AM.
When the AM or FM input source is selected, these
buttons are used to tune the tuner, or select radio
presets.
ꢈꢍ Pause button or Preset Memory button [33,
35, 40]
ꢃ Disc tray [33]
Discs are loaded here.
This button is used to pause playback. While play-
back is paused, pressing this button moves the video
forward one frame at a time.
When the AM or FM input source is selected, this
button is used to store the radio presets.
ꢄ Open/Close button [33]
This button is used to open and close the disc tray.
The input source is automatically set to DVD.
ꢅ Stop button [34]
This button is used to stop playback.
ꢆ Play button [33]
This button is used to start playback.
The input source is automatically set to DVD.
ꢇ Master Volume control [31] and indicator
This control is used to adjust the volume of the
DVD receiver to Min, 1 through 79, Max.
Phones jack [31]
This 1/4-inch phone jack is for connecting a stan-
dard pair of stereo headphones for private listening.
ꢈꢉ HDMI button [30]
This button is used to turn HDMI on or off.
ꢈꢊ HDMI indicator [30]
This indicator lights up when a HDMI signal is
being output.
ꢈꢋ Remote control sensor [11]
This sensor receives control signals from the remote
controller.
12
Front & Rear Panels—Continued
Display
ꢀ
ꢂ
ꢁ
ꢃ ꢄ ꢅ ꢆ ꢇ
ꢊ
ꢏ
ꢎ
ꢋ ꢈ
ꢀ MUTING indicator
ꢌ
ꢉ ꢍ ꢐ
ꢒ
ꢑ
ꢈꢊ SLEEP indicator
This indicator flashes while the DVD receiver is
muted.
This indicator lights up when the Sleep function has
been set.
ꢁ Tuning indicators
ꢈꢋ GROUP indicator
AUTO: This indicator lights up when the Auto Tun-
ing mode is selected, and disappears when the Man-
ual Tuning mode is selected.
While stopped, the total number of groups on the cur-
rent DVD-Audio disc is displayed here. During play-
back, the number of the current group is displayed.
: This indicator lights up when the DVD
receiver is tuned into a radio station.
FM ST: This indicator lights up when the DVD
receiver is tuned to a stereo FM station.
ꢈꢌ TITLE indicator
During playback, the number of the current title is
displayed.
ꢈꢍ Message & time area
ꢂ Listening mode & format indicators
These indicators show the currently selected listen-
ing mode and the format of the playing disc.
Time information, such as total time, remaining
time, and so on, is displayed here in hours, minutes,
and seconds. Other messages are also displayed.
ꢈꢎ CHP indicator
This indicator appears while the number of the cur-
rent chapter is being displayed.
ꢈꢏ TRACK indicator
ꢃ Playback mode indicators
MEM: Lights up when memory playback is
selected.
RDM: Lights up when random playback is selected.
REPEAT: Lights up when repeat playback is
selected for all the tracks.
REPEAT 1: Lights up when repeat playback is
selected for a track.
This indicator appears while track numbers are
being displayed. While stopped, the total number of
tracks on the current SACD or audio CD are dis-
played. During playback, the number of the current
track is displayed.
ꢄ Disc type indicators
These indicators show the type of disc loaded.
ꢈꢐ PRGSV indicator
ꢅ Data type indicators
This indicator appears when progressive video is
being output by the component video output.
These indicators show the type of data loaded.
ꢆ Disc operation indicators
ꢈꢑ TOTAL indicator
These indicators show the status of disc playback.
This indicator appears while the total number or
total time is being displayed.
ꢇ DIGITAL indicator
This indicator lights up when the digital audio sig-
nal input is used.
ꢈꢒ REMAIN indicator
This indicator appears while the remaining time is
being displayed.
ANALOG indicator
This indicator lights up when the analog audio sig-
nal input is used.
ꢈꢉ Camera angle
indicator
This indicator appears if the DVD-Video disc being
played features multiple camera angles.
13
Front & Rear Panels—Continued
Rear Panel
ꢁ
ꢂ
ꢀ
ꢃ ꢄ ꢅ
ꢆ
ꢇ
ꢊ ꢋ ꢈ ꢌ ꢉ ꢍ ꢐ
ꢀ SPEAKERS [18]
COAXIAL DIGITAL AUDIO IN [25]
This coaxial digital audio input can be connected to
a coaxial digital audio output on a DVD recorder or
game console.
This input is assigned for VIDEO 2/DOCK INPUT
in default.
If you output audio from this input during VIDEO 1
INPUT is selected, you must change the “Video1
Input” setting to “Coax” from “OPT” (page 54).
These terminal posts are for connecting your front
speakers.
ꢁ HDMI IN/OUT [26]
HDMI (High Definition Multimedia Interface) con-
nections carry digital audio and digital video.
The HDMI input is for connecting components with
HDMI outputs. The HDMI output is for connecting
a TV or projector with an HDMI input.
ꢈꢉ
REMOTE CONTROL [25]
ꢂ COMPONENT VIDEO OUTPUT [24]
These jacks output component video and can be
connected to an component video input on a TV or
projector.
This
nected to an
receiver remote controller can then be used to con-
trol the RI Dock. To use , you must make an
(Remote Interactive) jack can be con-
jack on Onkyo RI Dock. The DVD
ꢃ VIDEO OUTPUT [23]
analog audio connection (RCA) between the DVD
receiver and the RI Dock, even if they are connected
digitally.
This RCA connector can be used to connect a TV or
projector with a composite video input.
ꢄ FM ANTENNA [18]
ꢈꢊ VIDEO 1 INPUT [24]
This jack is for connecting an FM antenna.
Here you can connect other video equipment. Input
jacks include composite video and analog audio
input.
ꢅ AM ANTENNA [19]
These push terminals are for connecting an AM
antenna.
ꢈꢋ VIDEO 2/DOCK INPUT [25]
Here you can connect Onkyo RI DOCK or other
video equipment. Input jacks include composite
video and analog audio input.
ꢆ AC INLET [28]
The supplied power cord is connected here. The
other of the power cord should be connected to a
suitable wall outlet.
ꢈꢌ SUBWOOFER PRE OUT [18]
A powered subwoofer can be connected here.
ꢇ OPTICAL DIGITAL AUDIO IN [25]
This optical digital audio input can be connected to
an optical digital audio output on a DVD recorder,
or game console.
ꢈꢍ RS232
This port is for connecting the DVD receiver to
external controllers.
This input is assigned for VIDEO 1 INPUT in
default.
If you output audio from this input during
VIDEO 2/DOCK INPUT is selected, you must
change the “Video2 Input” setting to “OPT” from
“Coax” (page 54).
ꢈꢎ IR IN/OUT [27]
A commercially available IR receiver can be con-
nected to the IR IN jack, allowing you to control the
DVD receiver when it’s out of sight, for example,
installed in a cabinet.
A commercially available IR emitter can be con-
nected to the IR OUT jack to pass IR (infrared)
remote control signals along to other components.
14
Front & Rear Panels—Continued
Remote Controller
ꢀ Standby/On button* [28]
This button is used to set the DVD receiver to
Standby or turn on.
ꢈ
ꢌ
ꢂ
ꢀ
Don’t turn on the DVD receiver until you’ve com-
pleted, and double checked all connections
(pages 23–27).
ꢉ
ꢍ
ꢐ
ꢒ
ꢁ Number buttons* [43, 44, 64]
These buttons are used to enter title, chapter, and
track numbers and to enter times for locating spe-
cific points in time.
ꢂ CLR button [40, 43, 44, 48]
This button is used to cancel various functions.
ꢁ
ꢃ
ꢃ TV Control buttons [52]
These buttons are used to control a TV. You must
enter the appropriate remote control code first.
ꢑ
ꢄ Disc and DVD receiver menu buttons
Top Menu button* [36, 38]
With DVD discs, this button displays the main
menu. With a JPEG disc, it displays thumbnails of
the images. With a Video CD, it turns PBC on or
off.
ꢄ
Menu button* [36, 38]
This button is used to display a menu on a DVD or
to open the Disc Navigator when using a JPEG disc.
ꢅ
ꢆ
Cursor
/
/
/
buttons* [36, 54, 58]
These buttons are used to navigate menus.
ꢏ
ꢎ
Enter button* [36, 54, 58]
This button is used to start playback of the selected
title, chapter, or track, and to confirm settings.
Setup button [54, 58]
This button is used to open and close the setup
menus.
ꢓꢋ
ꢓꢈ
ꢇ
ꢊ
ꢋ
Return button [54]
This button is used to return to the previous display
when changing settings.
15
Front & Rear Panels—Continued
ꢅ Basic Playback buttons*
ꢈꢌ Search button [40, 43, 44]
This button is used to search for titles, chapters,
groups, folders, tracks, and specific points in time.
When the AM or FM input source is selected, you
can tune into AM and FM stations directly by enter-
ing the appropriate frequency.
Pause
button [33, 35]
This button is used to pause playback. While play-
back is paused, pressing this button moves the video
forward one frame at a time.
Play
This button is used to start playback.
Stop button [34]
This button is used to stop playback.
button [33]
ꢈꢍ Memory button [47]
This button is used with the Memory function.
When the AM or FM input source is selected, this
button is used to store the radio presets.
Fast Reverse/Fast Forward
[35]
These buttons are used for fast reverse and fast forward.
/
buttons
ꢈꢎ Last Memory button [48]
This button is used with the Last Memory function
for DVD playback.
Previous/Next
The Previous [
vious chapter or track. During playback it selects
the beginning of the current track.
/
buttons [34]
ꢈꢏ Muting button [32]
This button is used to mute or unmute the DVD
receiver.
] button is used to select the pre-
ꢈꢐ VOL
/
button [31]
The Next [
] button is used to select the next
This button is used to adjust the volume of the DVD
receiver.
chapter or track.
ꢆ Advanced Playback buttons
ꢈꢑ Tuner buttons
Audio button [50]
Tuning
/
button [39]
This button is used to select foreign language
soundtracks and audio formats (e.g., Dolby Digital
or DTS) on DVD-Video discs.
When the AM or FM input source is selected, the
Tuning [ ]/[ ] buttons are used to tune the tuner.
Preset
/
buttons [40]
Subtitle button [50]
When the AM or FM input source is selected, the
Preset [ ]/[ ] buttons are used to select radio pre-
sets.
This button is used to select subtitles on
DVD-Video discs.
Angle button [49]
This button is used to select camera angles on
DVD-Video discs.
ꢈꢒ Mode button* [39]
This button is used to select the Auto or Manual
tuning mode.
Random button* [46]
ꢓꢉ Subwoofer Level button [32]
This button is used to access the Subwoofer Level
menu.
This button is used with the Random function.
Repeat button* [45]
This button is used to set the Repeat function.
Use the Left and Right [ ]/[ ] buttons to adjust the
volume.
A-B button [45]
This button is used to set the A-B Repeat function.
ꢓꢊ Listening Mode button [41]
ꢇ Display button [51]
This button is used to select the listening modes.
This button is used to display information about the
disc or the current input source. Press it repeatedly
to display more information.
For buttons to control an Apple iPod in RI Dock with
an RI connection, see page 53.
*
Aspect/Zoom button [49, 59]
This button is used to change the view mode. Press-
ing and holding it for a few seconds selects Zoom
mode.
ꢈꢉ Resolution button [30]
This button is used to select a video resolution for
the HDMI OUT.
ꢈꢊ Sleep button [32]
This button is used with the Sleep function.
ꢈꢋ Input
/
button [31]
This button is used to select the input sources.
16
Connecting the DVD receiver
Placing the Speakers
Connecting Your Speakers
Front Left and Right Speakers
Speaker Connection Precautions
• Place the front left and right speakers symmetrically
and so that the distance from the listening position is
the same.
• When placing speakers, direct the speakers toward the
position of the listener’s ears where the listener sits to
enjoy music or movies.
Read the following before connecting your speakers:
• You can connect speakers with an impedance of
between 6 and 16 ohms. If you use speakers with a
lower impedance, and use the DVD receiver at high
volume levels for a long period of time, the built-in
protection circuit may be activated.
• Place the two speakers so that the heights of the two
speakers are aligned. The ideal height for the speakers
is the height of the listener’s ears.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive
(+) terminals, and negative (–) terminals only to nega-
tive (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
TV or screen
FL
FR
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the
positive and negative wires.
Doing so may damage the
DVD receiver.
• Make sure the metal core of
the wire does not have contact
FL: Front left speaker
FR: Front right speaker
with the DVD receiver’s rear
Subwoofer
panel. Doing so may damage the DVD receiver.
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the DVD receiver.
• Don’t connect one speaker to several terminals.
Using a subwoofer greatly improves the volume level
and sound quality of bass sounds. The subwoofer
effect depends not only on the listening position but
also on the shape of the listening room.
• In general, place the subwoofer in a corner of the room
or at a point 1/3 the width of the room.
• Play a movie or music that contains high quality bass
sounds to determine the subwoofer placement.
Change the subwoofer’s position and check the effect,
then select the position where the bass sounds are best
heard.
Corner
1/3room
length
17
Connecting the DVD receiver—Continued
Connecting the Speaker Cables
Connecting Antenna
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The DVD receiver won’t pick up any radio signals with-
out any antenna connected, so you must connect the
antenna to use the tuner.
Strip about 5/8" (15 mm)
of insulation from the
ends of the speaker
cables, and twist the bare
wires tightly, as shown.
5/8" (15 mm)
1
Unscrew the terminal.
AM antenna push terminals
FM antenna connector
2
Fully insert the bare
wires.
3
Screw the terminal tight.
Connecting the Indoor FM Antenna
4
The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
1
The following illustration shows which speaker should
be connected to each pair of terminals.
Front right
speaker
Front left
speaker
Insert the plug fully
into the jack.
Once your DVD receiver is ready for use, you’ll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
Use thumbtacks or something similar to
fix the FM antenna into position.
2
Connecting a Powered Subwoofer
Using a suitable cable, connect the DVD receiver’s SUB-
WOOFER PRE OUT to an input on your powered sub-
woofer, as shown.
Thumbtacks, etc.
Powered
subwoofer
LINE INPUT
Caution: Be careful that you don’t injure yourself
when using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead (see page 19).
18
Connecting the DVD receiver—Continued
Connecting the AM Loop Antenna
Connecting an Outdoor FM Antenna
The supplied indoor AM loop antenna is for indoor use
only.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
1
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
Connect both wires of the AM loop
antenna to the AM antenna push termi-
nals, as shown.
2
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
The antenna connection is polarity sensitive. Con-
nect the black wire to the ground terminal ( ).
Connect the other wire to the other terminal.
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
Push
Insert wire
Release
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If cir-
cumstances demand it, use a TV/FM antenna splitter, as
shown.
Black
Once your DVD receiver is ready for use, you’ll
need to tune into an AM radio station and adjust
the position of the AM antenna to achieve the best
possible reception.
TV/FM antenna splitter
To DVD receiver
To TV (or VCR)
Keep the antenna as far away as possible from
your DVD receiver, TV, speaker cables, and
power cords.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna (see page 20).
19
Connecting the DVD receiver—Continued
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
Black
White
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
20
Connecting the DVD receiver—Continued
AV Cables & Connectors
Video
Cable
Jack
Description
HDMI connections can carry uncompressed, stan-
dard or high definition digital video and digital
audio, for the best picture and sound quality.
HDMI
Component video separates the luminance (Y) and
color difference signals (PR, PB), providing the best
picture quality. Some TV manufacturers label their
component video inputs differently.
Y
P
P
Y
Component
video
/
/
B
R
C
B
P
P
B
R
CB
/ CR
/ CR
Composite
video
(supplied)
Composite video can be found on virtually all TVs,
VCRs, and video equipment.
Audio
Cable
Jack
Description
Optical digital audio connections provide better
audio quality than analog connections.
Optical digital
Coaxial digital
Coaxial digital audio connections provide better
audio quality than analog connections.
RCA analog audio connectors can be found on vir-
tually all AV components.
Analog
21
Connecting the DVD receiver—Continued
Video Output/Video Setting Matrix
The following matrix shows how the video outputs work in relation to the various video settings.
✓: Output
HDMI Output Setting (page 29, 30)
Setting
On (default)
Off
HD Resolution (page 30)
Progressive Setting (page 30)
Video output
Auto
480p (default)
720p, 1080i
Progressive
No output
Interlace
*3
HDMI
✓
✓
✓
No output
*1
*2
*2
Component
Composite
✓
✓
No output
No output
✓
✓
✓
*1
✓
✓
✓
*1 No picture will be output from other than HDMI when you connect the TV that the native resolution is “720p” or “1080i”.
*2 If your TV doesn’t support progressive scanning, you’ll get no picture.
*3 If your TV doesn’t support the “HD Resolution” settings of “720p” and “1080i”, you’ll get no picture.
Video Signal Flow Chart
Video input signals flow through the DVD receiver as shown.
HDMI input pass through HDMI output signals as it is.
Set top box, VCR, DVD recorder, etc.
VIDEO 1
VIDEO 2/DOCK
Composite
Composite
HDMI
HDMI IN
V IN
V IN
DVD
HDMI OUT
VIDEO OUT
Composite
COMPONENT OUT
HDMI
Component
TV, projector, etc.
22
Connecting the DVD receiver—Continued
Before Making Any Connections
• Read the manuals supplied with your AV components.
• Don’t connect the power cord until you’ve completed
all audio and video connections.
• Push each plug in all the way to
Right!
make a good connection (loose
connections can cause noise or
malfunctions).
RCA AV Connection Color Coding
• To prevent interference, keep
audio and video cables away from
power cords and speaker cables.
Wrong!
RCA AV connections are usually color coded: red,
white, and yellow. Use red plugs to connect right-chan-
nel audio inputs and outputs (typically labeled “R”). Use
white plugs to connect left-channel audio inputs and out-
puts (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
Optical Digital Jacks
The DVD receiver’s optical digital connectors have a
shutter-type cover that opens when an optical plug is
inserted, and closes when it’s removed. Push the plug in
all the way.
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
Analog audio
Right (red)
Left (white)
Right (red)
Left (white)
Composite video (Supplied)
(Yellow)
(Yellow)
Basic Setup
The setup described here is a basic setup that allows you to play discs using just the cables supplied with the receiver.
TV
Video cable
VIDEO IN
(Supplied)
Power cord
(Supplied)
To power outlet
1. Connect the VIDEO OUTPUT jack to the com-
posite video input on your TV.
This receiver is equipped with copy protection tech-
Use the supplied Video cable (RCA), connecting the
nology. Do not connect this receiver to your TV via a
yellow plug to the video output.
VCR using Video cable, as the picture from this
See the following page if you want to use other cable
receiver will not appear properly on your TV. (This
for the video connection.
receiver may also not be compatible with some com-
bination TV/VCRs for the same reason; refer to the
manufacturer for more information.)
2. Connect the supplied AC power cord to the AC
INLET, then plug into a power outlet.
23
Connecting the DVD receiver—Continued
Connecting Your TV
(video connection)
Connecting Other AV Component
You can use an AV cable to connect VIDEO 1 INPUT L/
R or V jack to your AV component such as a set top box,
VCR, and DVD recorder.
Connect your AV component’s analog audio and Video
output jack to the DVD receiver’s VIDEO 1 INPUT L/R
or V jack.
• Connect the DVD receiver directly to your TV. If you
connect the DVD receiver through a VCR, TV/VCR
combination, or video selector, the picture may be dis-
torted because DVD-Video discs are usually copy pro-
tected.
VIDEO
OUT
AUDIO
OUT
Using Component Video
L
R
You can use the component video output instead of the
standard video out jack to connect this receiver to your
TV (or other equipment).
This will provide better quality picture than composite
video.
Set top box,
VCR, DVD
Recorder
This jack cannot output the signal from composite
video input.
• Use a component video cable (not supplied) to con-
nect the COMPONENT VIDEO OUTPUT jacks to a
component video input on your TV (or monitor).
If you connect the component video output to a TV or
another component that doesn’t support progressive
scanning, be sure to turn off HDMI (see page 30).
You can set the component video output to Progressive
or Interlaced (see page 30).
Note:
You can also use optical/coaxial digital cable instead of
the audio cable (see page 25).
TV
COMPONENT
VIDEO IN
Y
PB
PR
Compatibility of this unit with progressive-scan TVs.
This receiver is compatible with progressive video
Macro Vision System Copy Guard.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE DIS-
PLAYED IN THE PICTURE. IN CASE OF 525 OR
625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE “STAN-
DARD DEFINITION” OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR TV SET COM-
PATIBILITY WITH THIS MODEL 525p AND 625p
DVD RECEIVER, PLEASE CONTACT OUR CUS-
TOMER SERVICE CENTER.
24
Connecting the DVD receiver—Continued
Connecting an RI Dock
■
iPod with video or RI Dock with the OSD mode
Connect your RI Dock’s analog audio output jacks
and Video output jack to the DVD receiver’s
■ iPod without video
Connect your RI Dock’s analog audio output jacks to
the DVD receiver’s VIDEO 2/DOCK INPUT jacks.
VIDEO 2/DOCK INPUT L/R jacks and V jack.
Connect the RI Dock with an
DS-A1 hookup shown below.)
cable. (Onkyo
Connect the RI Dock with an
cable. (Onkyo
DS-A1X/A2/A2X hookup shown below.)
Notes:
• Set the RI Dock’s RI MODE switch to HDD or HDD/DOCK.
• Press the Input [ ]/[ ] buttons to select “VIDEO2/DOCK”.
• Refer to the RI Dock’s instruction manual.
Digital Audio Connection
You can use optical/coaxial digital cable instead of the audio cable when connecting with other AV components.
Connect your AV component’s digital audio output jack to corresponding COAXIAL or OPTICAL DIGITAL AUDIO
IN jack of the DVD receiver.
You must assign that jack to an input (see page 56).
Notes:
VIDEO
OUT
• Optical digital audio input is assigned for VIDEO 1
OPTICAL
COAXIAL
INPUT in default.
If you output audio from this input during VIDEO 2/
DOCK INPUT is selected, you must change the
“Video2 Input” setting to “OPT” from “Coax”.
• Coaxial digital audio input is assigned for VIDEO 2/
DOCK INPUT in default.
Set top box,
VCR, DVD
Recorder
If you output audio from this input during VIDEO 1
INPUT is selected, you must change the “Video1
Input” setting to “Coax” from “OPT”.
Connect one
or the other
25
Connecting the DVD receiver—Continued
Notes:
Connecting your HDTV or AV
• The DVD receiver supports HDCP (High-bandwidth
Digital Content Protection), a protection system for
digital video. HDMI components that you connect to
the DVD receiver must also support HDCP.
• The DVD receiver supports High-Definition Multime-
dia Interface Specification Information Version 1.0.
component with an HDMI connection
This section shows how to connect the DVD receiver to
an HDTV, projector, or game console that has an HDMI
input/output socket.
What is HDMI?
HDMI & the DVD receiver
HDMI (High Definition Multimedia Interface) is a new
connection format that can carry uncompressed, stan-
dard or high definition digital video and digital audio.
Until now, several separate video and audio cables have
been required to connect AV components together. With
HDMI, a single cable is all that’s necessary to achieve
the best picture quality.
HDMI video is compatible with DVI (Digital Visual
Interface). To send HDMI video to a DVI input requires
an HDMI-to-DVI cable. The DVD receiver supports
HDCP (High-bandwidth Digital Content Protection),
and for an HDMI-to-DVI connection to work, the other
component must also support it. Note that this may not
work with some DVI components.
■ Video
The DVD receiver’s HDMI OUT supports the following
video resolutions:
• 720 x 480p (progressive), 60 Hz
• 1280 x 720p (progressive), 50/60 Hz
• 1920 x 1080i (interlaced), 50/60 Hz
If the connected HDTV or projector doesn’t support a
resolution, you may get no picture.
On the DVD receiver, you can select a resolution suit-
able for use with the connected HDTV or projector (see
page 30).
■ Audio Formats
The DVD receiver’s HDMI OUT supports the following
Using HDMI
audio formats:
• PCM (96 kHz, 48 kHz, 44.1 kHz)
• Dolby Digital
Use the HDMI cable (not supplied) to connect the DVD
receiver’s HDMI OUT to an HDMI input on your TV.
In the same manner, connect the DVD receiver’s HDMI
IN to an HDMI OUT on the game console, etc.
• DTS
Notes:
HDMI
IN
HDTV,
• If your HDMI-compatible TV or projector doesn’t
support Dolby Digital and DTS, the HDMI OUT will
not output digital audio in that format. In this case, set
the “Digital/HDMI Audio Out” setting to “PCM” (see
page 61).
projector
HDMI cable
(not supplied)
• If your TV doesn’t support digital audio at high sam-
pling rates, set the “Linear PCM Out” setting to
“Down Sample On”, so that it’s down sampled to
below 48 kHz (see page 61).
HDMI
• Note that audio from SACD discs or audio from the
multi channel area of a DVD-Audio discs is not output
by the HDMI OUT.
• The audio signal input from HDMI IN is not output
from the speakers connected to the DVD receiver but
only from the TV.
With some TVs and input signals, no sound may be
output. In these cases, set the connected device’s out-
put to PCM.
HDMI
IN
HDMI
• Audio and video inputs from VIDEO 1 INPUT or
VIDEO 2/DOCK INPUT are not be output from
HDMI OUT.
HDMI cable
(not supplied)
Game Console, etc.
26
Connecting the DVD receiver—Continued
Using a Multiroom Kit with Other
Components
Using the Multiroom Control Kits
To control the DVD receiver with the remote controller
when DVD receiver is located in a cabinet, you’ll need a
commercially available multiroom remote control kit.
• Multiroom kits are made by Niles and Xantech.
These kits can also be used when control other compo-
nents.
In this setup, an IR emitter is connected to the DVD
receiver’s IR OUT jack and placed in front of the other
component’s remote control sensor. Infrared signals
received at the DVD receiver’s IR IN jack are fed
through to the other component via the IR emitter. Sig-
nals picked up by the DVD receiver’s remote control
sensor are not output.
Using a Multiroom Kit with a Cabinet
In this setup, the IR receiver picks up the infrared signals
from the remote controller and feeds them to the DVD
receiver located in the cabinet via the connecting block.
IR Receiver
Connecting
block
IR IN
IR OUT
DVD receiver
IR Emitter
IR Receiver
Connecting
block
Remote controller
Other component
IR IN
DVD receiver
Signal flow
Inside
cabinet
The IR emitter should be connected to the DVD
receiver’s IR OUT jack, as shown below.
Remote controller
Signal flow
Other component
The miniplug cable from the connecting block should be
connected to the DVD receiver’s IR IN jack, as shown
below.
Remote control
sensor
Miniplug cable
Emitter
Miniplug cable
Miniplug
From the connecting block
IR Emitter
DVD receiver
Signal flow
DVD receiver
27
Connecting the Power/Turning on the DVD receiver
Before connecting
• Before unplugging the receiver from
• Make sure that all the connections on pages 17–27 are
the power outlet, make sure you first
complete (the connection to a TV is required).
switch it into standby.
• For the above reasons, do not plug this
Standby/On
Standby indicator
receiver into a switched power supply
found on some amplifiers and AV
receivers.
To a wall outlet
Standby/On
Press [Standby/On] button on the
DVD receiver or the remote con-
troller.
2
DVD receiver
Turn on your TV and select the
input through which the DVD
receiver is connected.
The DVD receiver turns on and the
Standby indicator turns off.
Remote
controller
• To put the DVD receiver in the standby
mode, press [Standby/On] on the DVD
receiver, or [Standby/On] on the
remote controller.
• While the Standby indicator lights up,
the DVD receiver can receive signals
from the remote controller.
• Setting the [Standby/On] button to
standby does not shut off the power
completely.
Note:
DVD receiver features a screen saver and an auto power
off function. If the receiver is stopped and no button is
pressed for 15 minutes, the screen saver starts (see
page 63).
Plug the supplied power cord into
the AC INLET and then into the
power outlet on the wall.
1
• Do not use a power cord other than the
one supplied with the DVD receiver.
The power cord supplied is designed
for use with the DVD receiver and
should not be used with any other
device.
• Never have the power cord discon-
nected from the DVD receiver while
the other end is plugged into the wall
outlet. Doing so may cause an electric
shock. Always connect by plugging
into the wall outlet last and disconnect
by unplugging from the wall outlet
first.
28
Initial Setup
This chapter explains the settings you need to make the
very first time the DVD receiver is turned on.
Basically this manual contains procedures using the
remote controller.
Here you need to make a few settings to get the DVD
receiver up and running. You can change these settings
later (see page 57).
Use the Up and Down [ ]/[
]
1
buttons to select “TV Shape”,
and then press [Enter].
Select “4:3 Letter box” or “4:3 Pan
Scan” if you have a 4:3 TV. Select
“16:9 Widescreen” or “16:9 Com-
pressed” if you have a widescreen TV.
See page 59 for more information.
Enter
Initial Setup
TV Shape
✔
4:3 Letter box
HDMI Output Setting
4:3 Pan Scan
On-Screen Language
16:9 Widescreen
16:9 Compressed
The “HDMI Output Setting” menu
appears next.
Use the Up and Down [ ]/[
]
2
3
First Time Setup
buttons to select “On” or “Off”
for “HDMI Output Setting”, and
then press [Enter].
The very first time you turn on the DVD receiver, the
“Initial Setup” menu appears onscreen.
Select “On” to use the HDMI output.
Initial Setup
TV Shape
Initial Setup
TV Shape
: 4:3 Letter box
✔
4:3 Letter box
HDMI Output Setting
HDMI Output Setting
4:3 Pan Scan
✔
On
On-Screen Language
16:9 Widescreen
On-Screen Language
Off
16:9 Compressed
The “On-Screen Language” menu
appears next.
Use the Up and Down [ ]/[
buttons to select a language, and
then press [Enter].
]
See page 61 for more information on
the language options.
TV Shape
: 4:3 Letter box
HDMI Output Setting
On-Screen Language
: On
✔
English
Français
Español
Deutsch
Italiano
The “Initial Setup” menu closes and the
setup is complete.
The DVD receiver is now ready to use.
Note:
You can cancel the “Initial Setup” by pressing the
[Setup] button and complete the settings later by using
the onscreen setup menus (see page 57).
29
HDMI and Progressive Settings
HDMI
Resolution
Note:
Tip:
Stop playback before perform these settings.
These settings can also be changed by using the onscreen
setup menus (see pages 59, 60).
Setting the HDMI
Note:
Be sure to choose a resolution that’s supported by your
TV. If you select a resolution that your TV doesn’t sup-
port, there will be no picture.
This section explains how to turn on the HDMI OUT and
change the video resolution when your TV or projector
is connected to the HDMI OUT.
Selecting Progressive or Interlaced
Press the DVD receiver’s [HDMI]
button to turn on HDMI.
1
If your TV supports progressive video, you can set the
DVD receiver to progressive and enjoy progressive
video on your TV. If your TV doesn’t support progres-
sive video, set the DVD receiver to interlaced.
DVD receiver
When HDMI output is at 480p, the component video
output is fixed at progressive and depending on the
selected resolution there may be no output, so turn off
the HDMI OUT before changing this setting.
Press the [Resolution] button
repeatedly to change the HDMI
resolution.
The first button press displays the cur-
rent resolution onscreen. Press the but-
ton again while the resolution is
displayed to change the setting.
2
Remote controller
Press the DVD receiver’s [HDMI]
1
button to turn off HDMI.
DVD receiver
The DVD receiver supports the following resolutions:
AUTO:
Use the [Resolution] button to
select “Progressive” or “Inter-
lace”.
The first button press displays the cur-
rent setting onscreen. Press the button
again while the setting is displayed to
change the setting.
The PRGSV indicator appears on the
display when progressive is selected.
The resolution is automatically set to the native resolu-
tion of the TV connected to the HDMI OUT.
If the DVD receiver does not support the TV’s native res-
olution setting, the resolution 480p will be used.
2
Remote controller
480p (default):
The setting displayed depends on the country in which
you purchased the DVD receiver.
720 ꢀ 480p 60Hz
Also output by the DVD receiver’s analog video outputs.
With this setting, component video output will be pro-
gressive.
720p:
1280 ꢀ 720p 50/60Hz
Not output by the DVD receiver’s analog video outputs.
1080i:
1920 ꢀ 1080i 50/60Hz
Not output by the DVD receiver’s analog video outputs.
30
Understanding Common Operations
Input
Sleep
Input selector
Master Volume control
Muting
VOL
/
Phones
When reproducing the audio and video signals from
HDMI IN, select “VIDEO 1”.
Adjusting the Volume
Remote
controller
DVD receiver
Using Headphones
You can connect a pair of stereo headphones (1/4-inch
phone plug) to the DVD receiver’s Phones jack for pri-
vate listening, as shown.
or
Use the Master Volume control, or the remote control-
ler’s VOL [ ]/[ ] button.
The volume can be set to “Min”, “1” through “79”,
“Max”.
Depending on subwoofer level or listening mode, the
maximum volume varies.
Notes:
• Always turn down the volume before connecting your
headphones.
• The speakers are turned off while the headphones plug
is inserted in the Phones jack.
Selecting the Input Source
Remote
DVD receiver
controller
• When you connect a pair of headphones, the listening
mode is set to “Stereo”, unless it’s already set to “Ste-
reo” or “Direct”.
or
• Only the Stereo and Direct listening modes can be
used with headphones (the listening modes available
also depend on the currently selected input source).
You can select DVD, FM, AM, or connected other AV
component (set top box, Onkyo RI Dock) as the input
source.
Use the DVD receiver’s Input selector to select the input
source.
To select the input source with the remote controller,
press the Input [ ] or [ ] button repeatedly.
DVD
VIDEO 1
VIDEO 2/DOCK
AM
FM
31
Understanding Common Operations—Continued
Muting the DVD receiver
Adjusting Subwoofer Level
You can temporarily mute the output of the DVD
receiver.
You can adjust the level of Subwoofer during play-
back.
Remote controller
Remote controller
Press the [Muting] button.
Press the [Subwoofer Level] but-
ton, and then use the Left and
Right [ ]/[ ] buttons to adjust
the volume.
The output is muted and the MUTING
indicator flashes on the display, as
shown.
You can adjust the volume of Sub-
woofer from –15 dB to +12 dB in 1 dB
steps.
MUTING
When you’ve finished, press the [Sub-
woofer Level] button again.
To unmute the DVD receiver, press the
[Muting] button again, or adjust the
volume.
The Mute function is cancelled when
the DVD receiver is set to Standby.
Using the Sleep Timer
With the sleep timer, you can set the DVD receiver to
turn off automatically after a specified period.
Remote controller
Press the [Sleep] button repeat-
edly to select the required sleep
time.
The sleep time can be set from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set. The specified sleep time appears on
the display for about five seconds, then
the previous display reappears.
If you need to cancel the sleep timer, press the [Sleep]
button repeatedly until the SLEEP indicator disappears.
To check the time remaining until the DVD receiver
sleeps, press the [Sleep] button. Note that if you press the
[Sleep] button while the sleep time is being displayed,
you’ll shorten the sleep time by 10 minutes.
32
Playing Discs
This chapter covers basic playback. Advanced playback
functions are covered in the “Advanced Playback” on
page 43.
Starting, Pausing & Stopping
Playback
This section explains how to start, pause, and stop play-
back.
Stop
Open/Close Play
■ Start
DVD receiver
To start playback, press the Play
] button.
[
Playback starts and the Play indica-
tor appears on the display.
If you’re playing a DVD-Video disc, or
a VCD with PBC (Playback Control),
you may need to start playback from a
menu (see page 36).
Pause
Remote controller
• For details on playing MP3, WMA,
or JPEG picture discs, see pages 37
and 38.
■ Pause
DVD receiver
To pause playback, press the
Pause [ ] button.
Playback pauses and the Pause indi-
cator appears on the display.
To restart playback, press the Play [
button. Playback restarts and the Pause
indicator disappears.
For DVD-Audio discs, pause cannot be
used while a menu is displayed.
]
Press [Open/Close] to open the
disc tray.
The input source is automatically set to
DVD.
1
Remote controller
DVD receiver
Load a disc.
2
Load a disc with the label side facing up,
using the disc tray guide to align the disc
(if you’re loading a double-sided DVD
disc, load it with the side you want to
play face down).
Press [Open/Close].
The disc tray closes and the relevant disc
type indicator appears on the display.
3
Tip:
If you press the Play [ ] button, the disc
tray will close and, depending on the
type of disc, playback will start automat-
ically.
Note:
Only load discs that are supported by the DVD receiver.
See pages 8 to 9.
33
Playing Discs—Continued
Select Next & Previous track/chapter
■ Stop
DVD receiver
To stop playback, press the Stop
] button.
[
DVD-V
DVD-A
SACD
CD
MP3
WMA
VCD
JPEG
Playback stops and the Play indica-
tor disappears.
This section explains how to skip to the next and previ-
ous track and chapter.
• When you stop playback of a
DVD-Video disc, the DVD receiver
remembers the point at which play-
back was stopped and “Resume”
appears onscreen. To resume play-
back from that point, press the Play
Remote controller
■ Select
Next
During Playback, press the Next
] button to select next track/
[
track/
chapter.
chapter
DVD receiver
The Next track/chapter starts playback.
[
] button. To cancel the “Resume”
function, press the Stop [ ] button
again. The Resume function is reset
when the disc is removed from the
DVD receiver.
Remote controller
• With the Last Memory function you
can resume playback from any point
even if the disc has been removed
(see page 48).
■ Select
During Playback, press the Previ-
Previous ous [
] button to select previ-
Notes:
track/
ous track/chapter.
• Prolonged display of the same picture or menu may
cause irreparable damage to your TV screen known as
screen burn-in. To prevent this, don’t keep playback
paused for too long and always press the Stop [ ] but-
ton when you’ve finished playing a DVD disc or VCD.
The DVD receiver features a screen saver to protect
your TV from the effects of burn-in (see page 63).
• With some DVD-Video discs, you may experience
picture noise that is not normally visible with standard
TV broadcasts. This is usually because DVD-Video
uses a lot of high-resolution video data. The amount of
noise, if any, will depend on your particular TV and
the problem can sometimes be alleviated by turning
down the TV’s sharpness control.
chapter
The first press selects the beginning of
the current track.
DVD receiver
Remote controller
34
Playing Discs—Continued
Forward Frame-by-Frame Playback
DVD-V
VCD
With frame-by-frame playback you can view individual
picture frames one at a time forward.
■ Forward Press the Pause [ ] button.
frame-by-
frame
Press it repeatedly to view sub-
sequent frames.
To resume normal playback, press the
Play [ ] button.
Fast Forward & Reverse
DVD-V
DVD-A
SACD
MP3
VCD
CD
This section explains how to fast forward and reverse.
■ Fast During playback, press the [
]
forward button to start fast forward.
Playback fast forwards and “ x2”
appears onscreen.
To change the fast-forward speed, press
the [ ] button repeatedly to select:
x2, x4, x8, x16.
To resume normal playback, press the
Play [ ] button.
■ Fast
reverse
During playback, press the [
button to start fast reverse.
]
Playback reverses and “ x2” appears
onscreen.
To change the fast-reverse speed, press
the [ ] button repeatedly to select:
x2, x4, x8, x16.
To resume normal playback, press the
Play [ ] button.
Notes:
• Fast forward and fast reverse may not always work at
the speed shown onscreen.
• For discs other than audio CDs, no sound is output
during fast forward or fast reverse.
• For DVD-Audio discs, fast forward and fast reverse
cannot be used while a menu is displayed.
35
Playing Discs—Continued
• On some DVDs, to display the disc menu, press the
[Menu] button.
• Since the multichannel input source of DVD-Audio is
down mixed, the output will be a processed audio. To
output an original audio, select the 2-channel source.
Some DVD-Audio discs may not be down mixed; in
this case select the 2-channel source.
Number
buttons
To set VCD’s PBC on and off
PBC menus can turned on or off by pressing the [Top
Menu] button.
Top Menu
Enter
Menu
Navigating CDs & Super Audio CDs
SACD
CD
This section explains how to play audio CDs and Super
Audio CDs with the “Disc Navigator”.
Load an audio CD or Super Audio
CD.
1
Navigating DVD & VCD Disc Menus
DVD-V
DVD-A
The “Disc Navigator” appears.
VCD
CDDA
Disc CD
-/13
DVD-Video discs usually have a menu from which you
can select titles, chapters, and other options, including
soundtracks, subtitles, and audio formats (e.g., Dolby
Digital or DTS). VCDs that support PBC (Playback
Control) may also have an onscreen menu.
/Track01.CDA
001. Track01
002. Track02
003. Track03
004. Track04
005. Track05
006. Track06
007. Track07
008. Track08
Repeat
:Off
Random :Off
Load a DVD or VCD.
1
With DVDs, a menu usually appears
when the Play [ ] button is pressed. If
it doesn’t, try pressing the [Top Menu]
button.
The tracks are displayed.
Use the Up and Down [ ]/[
buttons to select a track, and
]
2
With VCDs that support PBC, you may
have to press the Play [ ] button to dis-
play the menu.
press [Enter] to start playback.
With SACDs, you can select the multi-
channel area, 2-channel area, or CD
layer by pressing the [Audio] button.
Since the multichannel area is down
mixed, the output will be a processed
audio.
On a DVD menu, use the arrow
2
[
], [ ], [ ], [ ] buttons to
select an item, and then press
[Enter].
To output an original audio, select the
2-channel area.
Note:
On a VCD menu, use the number
buttons to select the tracks.
If the VCD’s menu consists of several
During random playback or memory playback, the arrow
buttons cannot be used.
pages, use the Next [
] and Previous
[
] buttons to view them. During
playback, you can return to the menu
by pressing the [Return] button.
Notes:
• Not all DVDs and VCDs have menus.
• Menu operation varies from disc-to-disc. See the
disc’s sleeve notes for details.
36
Playing Discs—Continued
Use the Up and Down [ ]/[
buttons to select tracks and sub-
folders in the open folder.
]
3
4
To open a folder in the list, press the
[Enter] button. To close a folder (i.e.,
move back up the directory tree), press
the [Return] button. Alternatively,
select the item at the top of the list and
press the [Enter] button.
Use the Left and Right [ ]/[ ] buttons
to display the other folders that contain
playable tracks.
Enter
/
/
/
Return
To play the selected track, press
the Play [ ] or [Enter] button.
If available, the ID3 tag information,
(Title name, Artist name, Album name,
and so on) will scroll across the bottom
of the screen.
Navigating MP3 & WMA Discs
or
MP3
WMA
Play
2/3
Disc DATA
3/11
This section explains how to play MP3 and WMA files
with the “Disc Navigator”.
00:00:29 00:03:58 00:04:27
/mp3/03 Track03.MP3
002. mp3
Repeat
:Off
001. Track01
002. Track02
003. Track03
004. Track04
005. Track05
006. Track06
007. Track07
Random :Off
Load an MP3 or WMA disc.
The “Disc Navigator” appears.
1
DATA
Disc – – – –
1/3
-/5
/mp3
Name: Onkyo Artist Name: Onkyo Album Name: Onkyo
001. ROOT
002. mp3
Repeat
:Off
Random :Off
For MP3 playback
003. MP3 music
001. Track01
002. Track02
003. Track03
004. Track04
005. Track05
Subsequent tracks in the same folder
are played in order.
Press the Stop [ ] button to stop
playback.
5
Initially, the folders in the root direc-
tory are displayed.
The DVD receiver numbers folders and
tracks in hierarchical order. You can
use these numbers to select folders and
tracks directly with the Search function
(see page 43).
Note:
During random playback or memory playback, the arrow
buttons cannot be used.
To open a folder, use the Up and
Down [ ]/[ ] buttons to select
it, and then press [Enter].
The contents of the folder are dis-
played.
2
37
Playing Discs—Continued
Viewing a Slideshow of JPEG Images
To open a folder in the list, press the
[Enter] button. To close a folder (i.e.,
move back up the directory tree), press
the [Return] button. Alternatively,
select the item at the top of the list and
press the [Enter] button.
Use the Left and Right [ ]/[ ] buttons
to display other folders that contain
JPEG images.
JPEG
This section explains how to display a slideshow of
JPEG images on your TV.
Load a JPEG disc.
The “Disc Navigator” appears.
1
DATA
1/17
/jpg
001. jpg
Disc – – – –
-/-
To play a slideshow, press the
Play [ ] or [Enter] button.
Subsequent images are displayed in
order, with each image being displayed
for five seconds.
4
Repeat
:Off
002. image0
003. image1
004. image2
005. image3
001. 001
Random :Off
002. 002
003. 003
or
To display an image for longer, press
the Pause [ ] button. Press the Play
Initially, the folders in the root direc-
tory are displayed.
[
] button to resume.
Use the Previous and Next [
]/[
]
The DVD receiver numbers folders and
files in hierarchical order. You can use
these numbers to select folders and files
directly with the Search function (see
page 43).
buttons to view the previous or next
image.
To flip a picture 180 degrees, use the
Up and Down [ ]/[ ] buttons (not
while zoomed in).
To rotate a picture counterclockwise or
clockwise, use the Left and Right [ ]/
[ ] buttons (not while zoomed in).
To zoom in or out, use the [ ] and
To open a folder, use the Up and
Down [ ]/[ ] buttons to select
it, and then press [Enter].
The contents of the folder are dis-
played.
2
Remote controller
[
] buttons. While zoomed in, use the
[ ]/[ ]/[ ]/[ ] buttons to move
around the picture.
To stop the slideshow, press the
Stop [ ] or [Menu] button.
5
The slideshow stops automatically
when all pictures have been displayed.
or
Use the Up and Down [ ]/[
buttons to select images and
subfolders in the open folder.
]
3
A thumbnail-size preview for the cur-
rently selected image is displayed.
■ To display thumbnails
To display thumbnails, in step 3, after opening the folder
you want to display, press the [Top Menu] button.
Use the arrow [ ], [ ], [ ], [ ] buttons to select the
thumbnails, and press [Enter] to start a slideshow. Press
the [Menu] button to return to the “Disc Navigator”.
DATA
1/17
/image1/001.JPG
Disc – – – –
-/-
005. image1
001. 001
002. 002
003. 003
004. 004
005. 005
006. 006
007. 007
Repeat
:Off
Random :Off
Use the Previous and Next [
play other pages.
]/[
] buttons to dis-
W: 150 H: 120
■ About HD JPEG
If your TV is connected via HDMI and the HDMI reso-
lution is set to 720p or 1080i, you can view your JPEG
images in high definition (see page 60).
38
Listening to the Radio
Tuning into Radio Stations
■ Auto Tuning Mode
Input
Search
Number
buttons
Press the [Mode] button so that
the AUTO indicator appears on
the display.
1
2
Memory
CLR
Press the Tuning [ ]/[ ] button.
Searching stops when a station is
found.
To stop searching, press Stop [ ] but-
ton.
Preset
Mode
Tuning
When tuned into a station, the
indicator appears.
When tuned into a stereo FM station, the FM ST indica-
tor appears on the display, as shown.
AUTO
FM ST
AUTO
FM ST
Note:
Using the Tuner
This procedure can also be performed on the DVD
receiver by using its Tuning/Preset [ ]/[ ] button. Press
the Tuning/Preset [ ]/[ ] button to start searching for a
few seconds. Pressing the Tuning/Preset [ ]/[ ] button
again stops the searching.
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets
for quick selection.
Listening to the Radio
After this, press the button repeatedly to change the fre-
quency one step at a time.
Use the Input [ ]/[ ] button to
select either AM or FM.
■ Manual Tuning Mode
In this example, FM has been selected.
Press the [Mode] button so that
the AUTO indicator disappears
from the display.
1
Band
Frequency
Press and hold the Tuning [ ]/
2
(Actual display depends on country)
[
] button.
The frequency stops changing when
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
HOLD
Radio Frequency can be changed in 0.2 MHz steps for
FM and 10 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
39
Listening to the Radio—Continued
■ Tuning into Stations by Frequency
You can tune into AM and FM stations directly by enter-
ing the appropriate frequency.
Selecting Presets
To select a preset, use the Preset
]/[ ] buttons.
[
Press the [Search] button.
1
Notes:
• This procedure can also be performed by using the
number buttons.
To enter, for example, “12”, press the [1] button fol-
lowed by the [2] button.
• This procedure can also be performed on the DVD
receiver by using its Tuning/Preset [ ]/[ ] button.
Within 8 seconds, use the num-
2
ber buttons to enter the fre-
quency of the radio station.
For example, to tune to 87.5 (FM),
press 8, 7, 5.
Deleting Presets
Presetting AM/FM Stations
Select the preset that you want to
delete.
See the previous section.
1
You can store a combination of up to 40 of your favorite
AM/FM radio stations as presets.
Tune into the AM/FM station that
you want to store as a preset.
Press the [CLR] button twice.
The preset is deleted and its number
disappears from the display.
1
2
Press the [Memory] button.
The preset number flashes.
2
While the preset number is flash-
3
ing (about 8 seconds), use the
Preset [ ]/[ ] buttons to select
a preset from 1 through 40.
Press the [Memory] button again
4
to store the station or channel.
The station or channel is stored and the
preset number stops flashing.
Repeat this procedure for all of your
favorite AM/FM radio stations.
Note:
This procedure can also be performed on the DVD
receiver by using its [Preset Memory] button and Tun-
ing/Preset [ ]/[ ] button. First press the [Preset Mem-
ory] button, use Tuning/Preset [ ]/[ ] button to select a
preset and then press the [Preset Memory] button again.
40
Using the Listening Modes
Selecting Listening Modes
About the Listening Modes
Direct
See “About the Listening Modes” in the right column for
detailed information about the listening modes.
In this mode, audio from the input source is output
directly with minimal processing, providing high-fidel-
ity reproduction.
Stereo
The selected input source is processed as a stereo signal
and output by the front left and right speakers and the
subwoofer if connected.
T-D (Theater-Dimensional)
With this mode you can enjoy a virtual 5.1 surround
sound even with only two speakers. This works by con-
trolling how sounds reach the listener’s left and right
ears. Good results may not be possible if there’s too
much reverb, so we recommend that you use this mode
in an environment with little or no natural reverb.
Notes:
• T-D listening mode cannot be selected while head-
phones are connected to the DVD receiver.
• During playback a DVD-Audio or SACD, T-D listen-
ing mode cannot be selected.
Listening
Mode
Press the [Listening Mode] but-
ton to select a listening mode.
Pressing this button repeatedly cycles
through all of the listening modes that
can be used with the current input
source.
41
Using the Listening Modes—Continued
T-D (Theater-Dimensional) Listening Angle
Setting
Use the Up and Down [ ]/[
]
2
buttons to select “Angle”, and
use the Left and Right [ ]/ [
buttons to select: “Narrow”,
“Middle”, or “Wide”.
Narrow: Select if the listening angle
is 20 degrees.
Middle: Select if the listening angle
is 30 degrees (default).
Wide: Select if the listening angle
is 40 degrees.
With this setting, you can specify the angle of the front
left and right speakers relative to the listening position.
Processing for the Theater-Dimensional listening mode
is based on this setting. Ideally, the front left and right
speakers should be equidistant from the listening posi-
tion and at an angle close to one of the three available
settings.
]
Front left speaker
Front right speaker
20/30/40°
When you’ve finished, press the
[Setup] button again.
3
The setup menu closes.
Press and hold the [Setup] but-
ton for 3 seconds.
When selecting the input other than
DVD, just press the [Setup] button.
“Balance” appears on the display.
1
Remote controller
Note:
Only when the T-D listening mode is selected, this set-
ting is available.
HOLD
Listening Mode and Receiver Settings
Depending on the listening mode, the setup menu settings may be enabled/disabled as shown below.
✔: available
Listening Mode
Settings
Page #
55
Direct
Stereo
✔
T-D
✔
Speaker Output Balance
Subwoofer Level
ꢁ
ꢁ
32
✔
✔
Correcting Sound and Picture
Sync
55
✔
✔
ꢁ
*1
Crossover Frequency
Enabling/Disabling the Subwoofer
Front Speakers Size
56
55
55
✔
✔
✔
✔
ꢁ
ꢁ
ꢁ
✔
*2
✔
*1 During playback a DVD-Audio or SACD, this setting is fixed at 100 Hz.
*2 During playback a DVD-Audio or SACD, this setting is fixed at Small.
42
Advanced Playback
Use the number buttons to spec-
ify a title, chapter, or track num-
ber.
To enter, for example, “12”, press the
[1] button followed by the [2] button.
2
Search
Number
buttons
Search
Title
Chapter
Disc
DVD-VIDEO Current/Total 12/ 19 Current/Total 5/
7
Entered title number
appears here
Enter
Entered chapter number
appears here
If you’re playing a DVD, MP3, or
WMA disc, use the Left and Right [ ]/
[ ] buttons to select the Title/Group/
Folder and Chapter/Track fields.
To clear a number, press the [CLR] but-
ton.
Selecting Chapters/Titles/Tracks/
Folders by Number
Press the Play [ ] or [Enter] but-
ton to start playback of the spec-
ified title, chapter, or track.
3
DVD-A
DVD-V
SACD
MP3
WMA
VCD
CD
With the “Search” function you can select chapters,
titles, and tracks by number. To use the function with
DVD, DVD playback is required.
or
Press the [Search] button.
The “Search” window appears
onscreen.
1
This is what appears for DVDs.
Search
Notes:
Title
Chapter
Disc
• During playback, you can select other chapters or
tracks directly by using the number buttons (i.e., with-
out pressing the [Search] button). For example, to
select chapter #2, simply press [2]. To select chapter
#10, press [+10] and [0].
DVD-VIDEO Current/Total 1/ 19 Current/Total - - -/ 78
This is what appears for CDs.
Search
• DVD-Video discs usually have menus for selecting
titles and chapters.
Track
Disc
CDDA
Current/Total - -/ 10
• When Video CD PBC is on, you can’t search for
tracks. Turn PBC off first.
• The [Search] button cannot be used during random
playback or memory playback.
• Search may not work with some discs.
43
Advanced Playback—Continued
Notes:
• In some cases, playback may start from a slightly dif-
ferent point to the one that you specify.
• Time search may not work with some discs.
• Time search cannot be used while a DVD-Video or
Video CD menu is displayed onscreen.
• The [Search] button cannot be used during random
playback or memory playback.
Search
Number
buttons
Enter
Searching by Time
DVD-V
SACD
DVD-A
VCD
CD
With the “Search” function you can search by time.
During playback, press the
1
[Search] button twice.
The “Search” window appears
onscreen.
Search
Time
Disc
DVD-VIDEO
-:- -:- -
Use the number buttons to enter
a time.
Time search only works within the cur-
rent title or track.
To enter, for example, 5 minutes, 30
seconds, press [5] [3] [0] buttons.
2
3
Search
Time
Disc
DVD-VIDEO
-:-5:30
To clear a number, press the [CLR] but-
ton.
Press the Play [ ] or [Enter] but-
ton to start playback of the spec-
ified time.
or
44
Advanced Playback—Continued
A-B Repeat Playback
DVD-V
SACD
MP3
VCD
CD
With the “Repeat A-B” function you can play a specified
section over-and-over again.
During playback, press the [A-B]
1
button to set the A point (i.e., the
start of the section you want to
repeat).
Repeat
A–B
“Repeat A-” appears onscreen and
“-R_A” appears on the display.
Press the [A-B] button again to
2
set the B point (i.e., the end of the
section you want to repeat).
Playback repeats between the A and B
points, and “Repeat A-B” appears
onscreen and “-R_AB” appears on the
display.
Repeat Playback
DVD-A
DVD-V
SACD
MP3
WMA
VCD
CD
JPEG
With the “Repeat” function you can play a disc, title,
chapter, group, track, or folder over-and-over again.
To cancel A-B repeat playback,
press the [A-B] button.
3
During playback, press the
1
[Repeat] button repeatedly to
select a repeat option.
The selected repeat option appears
onscreen.
Notes:
• The “Repeat A-B” function may not work with some
DVD-Video discs and VCDs that support PBC.
• In some cases, the A and B points may be at slightly
different points to the ones that you specify.
The available options depend on the
type of disc, as follows:
DVD-Video: Chapter Repeat, Title
Repeat, Disc Repeat, Repeat Off.
DVD-Audio: Track Repeat, Group
Repeat, Repeat Off.
SACD, VCD, CD: Track Repeat, Disc
Repeat, Repeat Off.
MP3, JPEG, WMA: Track Repeat,
Folder Repeat, Disc Repeat, Repeat
Off.
To cancel repeat playback, use
the [Repeat] button to select
“Repeat Off”.
2
Notes:
• Repeat playback may not work with some discs.
• If the “Memory Playback” function is on (see
page 47), the selectable options are “Memory
Repeat”, which plays the playlist repeatedly, and
“Repeat Off”.
• To use the Repeat function with a VCD that supports
PBC, you must first turn off PBC (see page 36).
45
Advanced Playback—Continued
• To use the “Random” function with a VCD that sup-
ports PBC, you must first turn off PBC (see page 36).
• If the “Memory Playback” function is on (page 47),
random playback is unavailable.
• You can’t use the [Search] button during random play-
back.
• During random playback, the remote controller’s
arrow [ ], [ ], [ ], [ ] buttons and number buttons
don’t work with the “Disc Navigator”.
• The “Random” function cannot be used with JPEG
files.
Random
Random Playback
DVD-V
DVD-A
SACD
CD
MP3
WMA
VCD
With the “Random” function you can enjoy a random
selection of titles, chapters, groups, tracks, or folders.
During playback, press the [Ran-
dom] button repeatedly to select
a random option.
1
The selected random option appears
onscreen.
The options available depends on the
type of disc, as follows:
DVD-Video: Title Random, Disc Ran-
dom, Random Off.
DVD-Audio: Group Random, Random
Off.
SACD, VCD, CD: Disc Random, Ran-
dom Off.
MP3, WMA: Folder Random, Disc
Random, Random Off.
With the “Title Random” option, chap-
ters within the current title are played at
random. With the “Disc Random”
option, titles, chapters, groups, tracks,
or folders on the disc are played at ran-
dom.
Random playback begins after the cur-
rent chapter or track has finished.
Random playback stops automatically
when all of the items have been played
once.
To cancel random playback, use
the [Random] button to select
“Random Off”.
2
Notes:
• Random playback may not work with some discs.
46
Advanced Playback—Continued
Repeat step 2 to add more items
to the memory list.
You can add up to 32 items to the mem-
ory list.
3
4
Number
buttons
Memory
Last
Memory
To play the memory list, press
the Play [ ] button.
CLR
The “Memory List” window must be
open when you press the Play [ ] but-
ton.
Enter
To stop playback, press the Stop
5
[
] button.
While playback is stopped, you can
delete the memory list by pressing the
[CLR] button.
While playback is stopped, you can
cancel the Memory Playback function
by pressing the Stop [ ] button again.
Memory Playback
Adding New Items to the List
DVD-A
DVD-V
SACD
MP3
WMA
VCD
CD
Use the Up/Down [ ]/[ ] but-
1
With the “Memory Playback” function you can create
your own memory list of titles, chapters, and tracks.
tons to select the step which you
want to insert the new item, and
then press the [Enter] button.
Press the [Memory] button.
1
The “Memory List” window appears
onscreen, as shown.
Memory List
No.
Title/Folder
Chapter/Track
Current/Total 001 / 019 Current/Total --- / 078
01
02
03
04
05
06
07
08
005 / 019
002 / 019
--- / 019
003 / 019
010 / 019
--- / 019
--- / 019
--- / 019
001 / 078
012 / 078
--- / 078
004 / 078
003 / 078
--- / 078
--- / 078
--- / 078
Memory List
Title/Folder
Current/Total 001 / 019 Current/Total --- / 078
No.
Chapter/Track
01
02
03
04
05
06
07
08
--- / 019
--- / 019
--- / 019
--- / 019
--- / 019
--- / 019
--- / 019
--- / 019
--- / 078
--- / 078
--- / 078
--- / 078
--- / 078
--- / 078
--- / 078
--- / 078
Enter the title/folder (group), and
chapter/track numbers of the
item to be inserted.
Use the remote controller’s Left/Right
[ ]/[ ] buttons to select the parame-
ters, and use the number buttons to
enter the number.
2
3
The top row ( ) is used to enter title/
folder and chapter/track numbers.
The steps in the memory list are num-
bered.
Enter the title/folder (group), and
chapter/track numbers of the
item you want to add to the mem-
ory list, and then press [Enter].
Use the remote controller’s Left/Right
[ ]/[ ] buttons to select the parame-
ters, and use the number buttons to
enter the number.
2
Press the [Enter] button.
The new item is inserted into the mem-
ory list and subsequent items move
down the list.
The new item is added to the memory
list as step 01.
47
Advanced Playback—Continued
Deleting Items from the List
Last Memory
DVD-V
Use the Up/Down [ ]/[ ] but-
tons to select it, and then press
the [CLR] button.
With the “Last Memory” function you can resume play-
back from where you left off even if the disc has been
removed and the DVD receiver has been set to Standby.
“Last Memory” also remembers the soundtrack and sub-
title settings you were using.
The item is deleted and subsequent
items move up the list.
During DVD playback, press the
[Last Memory] button.
1
The last memory point for the disc is
stored, “Last Mem” appears on the dis-
play.
If the [Last Memory] button is pressed
again, the last memory point is updated.
Editing Steps
Use the Up/Down [ ]/[ ] but-
1
tons to select the step.
To stop playback, press the Stop
2
[
] button.
Now you may remove the disc
and turn off the DVD receiver.
Use the Left/Right [ ]/[ ] but-
To resume playback, load the
disc, and then press the Play [
button.
The “Last Memory” dialog box
appears.
2
3
tons and number buttons to edit
the title/folder (group) or chapter/
track numbers, and then press
[Enter].
]
Last Memory is set.
Start playback from memory location?
Yes
No
Memory Clear
To resume playback from the last
memory point, select “Yes”, and
then press [Enter].
4
To start playback from the present
point, select “No”, and then press
[Enter].
To delete the last memory point, select
“Memory Clear”, and then press
[Enter].
Notes:
• The “Last Memory” function can store the last point
for up to six DVDs. When you set the “Last Memory”
function for a seventh disc, the first disc’s settings are
deleted.
• The “Last Memory” function will not work while a
menu is being displayed onscreen.
Notes:
• To close the “Memory List” window, press the
[Return] button.
• The memory list will be deleted when the DVD
receiver is set to Standby or the disc tray is opened.
• To use this function with a VCD that supports PBC,
you must first turn off PBC.
• The “Last Memory” function may not work with some
DVDs.
• The Memory Playback function cannot be used with
some discs.
• JPEG images can be added to the memory list, how-
ever, they will not be displayed.
48
Advanced Playback—Continued
Selecting Camera Angles
DVD-V
Some DVDs feature multiple camera angles that allow
you to view scenes from different angles. When a DVD
features multiple camera angles, the camera indicator
appears on the display. Such discs usually have the cam-
era angle logo ( ) printed on the sleeve.
/
/
/
Press the [Angle] button repeat-
edly to cycle through the avail-
able camera angles.
The number of the currently selected
camera angle appears onscreen. For
example, on a disc with three camera
angles, you’d see 1/3, 2/3, and 3/3.
Angle
Zoom
Notes:
Zooming
• With some DVDs you may not be able to select differ-
ent camera angles even though the camera
tor is displayed.
• With some DVDs you can select camera angles from
a menu.
indica-
DVD-V
VCD
JPEG
With the Zoom function you can enlarge any part of the
picture.
During playback or while play-
1
back is paused, press and hold
the [Zoom] button for 3 seconds.
“Zoom x1.0” appears onscreen.
HOLD
Press the [Zoom] again repeat-
edly to Zoom in.
2
The number of zoom steps available
depends on the resolution of the disc or
file.
After the maximum zoom, the picture
returns to its normal size.
To see other areas of the picture
while zoomed, use the remote
controller’s arrow [ ], [ ], [ ],
3
[
] buttons.
Notes:
• The Zoom function may not work with some discs.
• The Zoom function cannot be used with HD JPEG.
• The Zoom function cannot be used with disc menus.
49
Advanced Playback—Continued
Selecting Subtitles
DVD-V
Some DVD-Video discs feature subtitles in several lan-
guages. See the disc’s sleeve notes for details.
During playback, press the [Sub-
title] button repeatedly to cycle
through the available subtitles.
The name of the selected subtitle
appears onscreen for several seconds.
To turn off subtitles, use the [Subtitle]
button to select “Off”.
Subtitle
Audio
Notes:
• When you stop playback and cancel the “Resume”
function (see page 34), the subtitle language will
revert to your default subtitle language (see page 61),
or the disc’s default subtitle language.
• With some DVDs you can select subtitles from a
menu, and you may not be able to select subtitles dur-
ing playback.
Selecting Soundtracks
DVD-V
DVD-A
SACD
Some DVD-Video discs feature soundtracks in several
languages or audio formats (e.g., Dolby Digital or DTS).
Music DVD-Video discs and DVD-Audio discs some-
times feature audio in several formats, such as PCM,
Dolby Digital, or DTS. See the disc’s sleeve notes for
details.
During playback, press the
[Audio] button repeatedly to
cycle through the available
soundtracks.
The name of the selected soundtrack
appears onscreen for several seconds.
For SACDs, you can select the multi-
channel area, 2-channel area, or CD
layer. If you make a selection during
playback, playback will stop.
Notes:
• With DVD-Video discs, when you stop playback and
cancel the “Resume” function (see page 34), the
soundtrack language will revert to your default lan-
guage (see page 61), or the disc’s default language.
• With some discs, selecting another soundtrack may
cause the picture to skip momentarily.
• With some DVDs you need to select soundtracks from
a menu, and you may not be able to select other
soundtracks during playback.
• Since the multichannel input source of SACD and
DVD-Audio is down mixed, the output will be a pro-
cessed audio. To output an original audio, select the 2-
channel source. Some DVD-Audio discs may not be
down mixed; in this case select the 2-channel source.
50
Disc and Input Information
■ Audio CD, Super Audio CD
Displaying Information
Onscreen:
You can display various information about the current
disc, or input source as follows.
• Current/total track number, elapsed track time,
remaining track time, and total track time.
• Current/total track number, elapsed disc time, remain-
ing disc time, and total disc time.
Remote controller
Press the [Display] button
repeatedly to cycle though the
available information.
Display:
• Elapsed track time
• Remaining track time
• Elapsed disc time
• Remaining disc time
During playback of a disc, various
information appears onscreen.
The operating status (e.g., Stop, Play,
Resume) and disc type information is
displayed along the top of the screen.
■ MP3, WMA
Onscreen:
Disc Information
• Current/total folder number, current/total track num-
ber in the folder, elapsed track time, remaining track
time (MP3 only), and total track time (MP3 only).
The information displayed depends on the type of disc,
as follows:
Display:
• Elapsed track time
• File name
• Folder name
■ DVD-Video
Onscreen:
• Current/total title number, elapsed title time, remain-
ing title time, total title time, selected soundtrack,
selected subtitle, and the number of available camera
• Total number of folders
angles.
■ JPEG
• Current/total chapter number, elapsed chapter time,
remaining chapter time, and total chapter time.
Display:
• Folder number, track number
Display:
• Elapsed chapter time
• Remaining title time
• File name
• Folder name
• Total number of folders
■ DVD-Audio
Input Information
Onscreen:
The information displayed depends on the type of input
source, as follows:
• Current/total track number, elapsed track time,
remaining track time, total track time, and selected
soundtrack.
Display:
• Current/total group number, elapsed group time,
remaining group time, and total group time.
• Input source
• Signal format*
Display:
• Listening mode
• Elapsed track time
• Remaining track time
• Elapsed disc time
* If the input signal is analog, no format information is
displayed.
■ Video CD
Onscreen:
• Current/total track number, elapsed track time,
remaining track time, and total track time.
• Current/total track number, elapsed track time,
remaining disc time, and total disc time.
Display:
• Elapsed track time
• Remaining track time
• Elapsed disc time
• Remaining disc time
Note:
If PBC is on, no information is displayed when the [Dis-
play] button is pressed.
51
Controlling Other Components
Controlling a TV connected to the
DVD receiver
Point the remote controller at the
TV, and check the operation.
If the remote controller doesn’t work as
expected, and several remote codes are
listed, try each one in turn and use the
one that works best.
4
You can control a TV. You must enter the appropriate
remote control code first.
Note:
Number
buttons
The remote control codes provided are correct at the time
of printing, but are subject to change.
Controlling a TV
TV
To control a TV, point the remote controller at it and use
the buttons explained below. With some TVs, certain
buttons may not work as expected, and some may not
work at all.
Enter
ꢂ
ꢃ
ꢀ
Entering Remote Control Codes
ꢁ
Look up the appropriate remote
1
2
control code in the “Remote Con-
trol Codes list” at the end of this
manual.
Hold down the TV [
] and
[Enter] buttons for about 3 sec-
onds.
HOLD
ꢀ TV [
] button
Sets the TV to Standby or On.
ꢁ TV [Input] button
Selects the TV’s AV input.
HOLD
ꢂ TV VOL [ ]/[ ] button
Adjusts the TV’s volume.
Within 30 seconds, use the num-
ber buttons to enter the 4-digit
remote control code.
3
ꢃ TV [CH +/–] button
Selects channels on the TV.
52
Controlling Other Components—Continued
ꢀ Standby/On button
Controlling an Apple iPod in RI Dock
connected to the DVD receiver
Sets the iPod to Standby or On.
ꢁ Playlist [ ]/[ ] buttons*
Used to select the previous or next playlist on the
iPod.
When operating an Apple iPod in RI Dock with an
connection, you can control it by DVD receiver’s remote
controller.
ꢂ Album [ ]/[ ] buttons*
When Using an RI Dock:
• Connect the RI Dock to the VIDEO 2/DOCK INPUT
jacks (see page 25).
• Set the RI Dock’s RI MODE switch to HDD or HDD/
DOCK.
Selects the next or previous album.
ꢃ TOP Menu button*
Used to access menus.
ꢄ Arrow [ ]/[ ] and Enter buttons*
• See to the RI Dock’s instruction manual for more
information.
Used to navigate menus and select items.
ꢅ Pause [ ] button
Press the Input [ ]/[ ]buttons to select “VIDEO2/
DOCK”.
Pauses playback. (With 3rd generation iPods, it
works as a Play/Pause button.)
ꢆ Rewind [
] button
Press and hold to rewind.
ꢇ Fast Forward [
] button
ꢂ
ꢀ
Press and hold to fast forward.
Random button*
Used with the shuffle function.
ꢈꢉ Repeat button*
Used with the repeat function.
ꢈꢊ Menu button
Works as a Mode button when used with a DS-A2/
A2X RI Dock.
ꢁ
ꢈꢋ Play [ ] button
Starts playback. If the component is off, it will turn
on automatically. (With 3rd generation iPods, this
button works as a Play/Pause button.)
ꢈꢌ Stop [ ] button
ꢃ
ꢄ
Stops playback and displays a menu.
ꢈ
ꢈꢍ Next [
] button
Selects the next song.
ꢈꢎ Previous [
] button
Restarts the current song. Press it twice to select the
previous song.
ꢌ
ꢉ
ꢈꢏ Mode button*
ꢅ
Turns on the backlight for 30 seconds.
* Buttons marked with an asterisk ( ) are not supported
by 3rd generation iPods.
*
ꢆ
ꢇ
ꢍ
ꢐ
ꢒ
Notes:
• Auto Power On Function
If you start iPod playback while the DVD receiver is
on Standby, the DVD receiver will automatically turn
on and select “VIDEO2/DOCK” input. Then, your
iPod will start playback.
ꢊ
ꢋ
• Direct Change Function
If you start iPod playback while listening to another
input source, the DVD receiver will automatically
select “VIDEO2/DOCK” input.
• When you don’t listen to the iPod, stop playback. The
direct change function activates at the change of tracks
to automatically change the input to “VIDEO2/DOCK”.
53
Configuring the DVD receiver
Setup Menu
Here you can configure the DVD receiver in this menu on display.
The configurations are common for the all input settings excluding “AVSync”, “Video1 Input” and “Video2 Input”.
Press and hold the [Setup] but-
ton for 3 seconds.
When selecting the input other than
DVD, just press the [Setup] button.
“Balance” appears on the display.
Use the Up and Down [ ]/[
buttons to select the menus and
use the Left and Right [ ]/[
buttons to select settings.
]
1
2
3
Remote controller
]
HOLD
When you’ve finished, press the
[Setup] button again.
The setup menu closes.
Press the [Return] button to return pre-
vious display.
For detailed information, refer to the pages in brackets.
B a l a n c e :
0
Speakers Output Balance [55]
S W L e v e l :
0
Operations
Subwoofer Level [32]
AV S y n c : 0 m s
Correcting Sound
and Picture Sync [55]
X o v e r : 1 0 0 H z
A n g l e : M i d d l e
*1
T-D Listening Angle [42]
Crossover Frequency [56]
L N i g h t : O f f
Late Night Function [55]
I n p u t : O P T
V i d e o 1 I n p u t
V i d e o 2 I n p u t
S u b w f r : Ye s
Audio Input Setup [56]
D i m m e r
:
1
Display Brightness [55]
F o r m a t : A u t o
A d v a n c e d
Digital Input Signal
Formats [56]
Enabling/Disabling
the Subwoofer [55]
*1 Only when the T-D listening
mode is selected, this setting
is available.
L o c k S e t u p
F r o n t : S m a l l
Lock Setup [55]
Front Speakers Size [55]
54
Configuring the DVD receiver—Continued
Speakers Output Balance
Lock Setup
Here you can adjust the output balance of speakers.
The balance can be adjusted from “L + 12” to “R + 12”
in 1 steps.
With this preference, you can protect your settings by
locking the setup menus.
When the setup menus are locked, you cannot change
any setting.
Note:
Locked: Setup menus locked.
Unlocked: Setup menus not locked.
When the listening mode is set to “Direct”, no effect will
be produced.
Enabling/Disabling the Subwoofer
Correcting Sound and Picture Sync
This section explains how to specify enabling/disabling
the subwoofer.
When using progressive scanning on your DVD receiver,
you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the
audio signals.
• You can set it from 0 to 100 milliseconds (msec) in 20
millisecond steps.
Yes: Select if a subwoofer is connected.
No: Select if no subwoofer is connected.
Front Speakers Size
• The setting is available for each input source other
than FM and AM.
This section explains how to specify
front speakers sizes.
Note:
For speakers with a cone diameter
larger than 6-1/2 inches (16 cm), spec-
ify “Large”. For those with a smaller
When the listening mode is set to “Direct”, no effect will
be produced.
diameter, specify “Small”. The cross-
over frequency can be changed on
page 56.
Cone diameter
Late Night Function (Dolby Digital only)
With the Late Night function, you can reduce the
dynamic range of Dolby Digital material so that you can
still hear quiet parts even when listening at low volume
levels—ideal for watching movies late at night when you
don’t want to disturb anyone.
Small: Select if the front speakers are small.
Large: Select if the front speakers are large.
Notes:
• If the “Enabling/Disabling the Subwoofer” the above
is set to “No”, this setting is fixed at “Large”.
• When the listening mode is set to “Direct”, no effect
will be produced.
Off: Late Night function off (default).
Low: Small reduction in dynamic range.
High: Big reduction in dynamic range.
Notes:
• Depending on the design of the contents, there are
some materials that will show no effect even when the
Late Night mode is operating.
• The Late Night function resets to the default when the
DVD receiver is set to Standby.
Display Brightness
You can adjust the brightness of the display.
1: Normal + Input selector and Master Volume
control light on.
2: Normal + Input selector and Master Volume
control light off.
3: Dim + Input selector and Master Volume con-
trol light off.
4: Dimmer + Input selector and Master Volume
control light off.
55
Configuring the DVD receiver—Continued
Crossover Frequency
Audio Input Setup
This setting only applies to the speakers that you speci-
fied as “Small” in the “Front Speakers Size” on page 55.
To get the best bass performance from your speaker sys-
tem, you need to set the crossover frequency according
to the size and frequency response of your speakers.
Use the diameter of the smallest speaker in your system
when choosing the crossover frequency.
If you connect a component to a digital input jack, you
must assign that jack to an input. For example, if you
connect your DVD recorder to the COAXIAL DIGITAL
AUDIO IN jack, you should assign that jack to the
“Video 1 input”. By default, the COAXIAL DIGITAL
AUDIO IN jack is assigned to the “Video 2 input”,
although this can be changed.
Here are the default assignments.
Speaker cone diameter
Crossover frequency
Input
VIDEO 1 INPUT
Default assignment
Over 8 in.
(20 cm)
40/50/60 Hz*
OPT
VIDEO 2/DOCK INPUT
Coax
6-1/2 to 8 in.
(16ꢁ20 cm)
5-1/4 to 6-1/2 in.
(13ꢁ16 cm)
3-1/2 to 5-1/4 in.
(9ꢁ13 cm)
Under 3-1/2 in.
(9 cm)
80 Hz
100 Hz(default)
120 Hz
OPT: optical digital audio input
Coax: coaxial digital audio input
ANA: analog audio input
Note:
The same audio input cannot be simultaneously assigned
to both VIDEO 1 INPUT and VIDEO 2/DOCK INPUT.
150/200 Hz*
*Choose the setting suitable for the speaker.
Digital Input Signal Formats
Notes:
The digital input signal formats are available only for the
input sources that you have assigned a digital input jack
(see above).
Normally, the DVD receiver detects the signal format
automatically. However, if you experience either of the
following issues when playing PCM or DTS material,
you can manually set the signal format to PCM or DTS:
• If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
• For a more accurate setting, look up the frequency
response in the manuals supplied with your speakers
and set accordingly.
• Choose a higher crossover frequency if you want more
sound from your subwoofer.
• When a DVD-Audio or an SACD is played in the Ste-
reo listening mode, no effect will be produced.
• When the listening mode is set to Direct, no effect will
be produced.
• If noise is produced when fast forwarding or reversing
a DTS CD, try setting the format to DTS.
DTS or PCM: The DTS or PCM indicator, depending
on which format you have set, flashes, and only signals
in that format are output. Digital signals in other formats
are ignored.
Auto (default): The format is detected automatically. If
no digital input signal is present, the corresponding ana-
log input is used instead.
56
DVD Onscreen Setup Menus
This chapter explains the various functions and settings of the onscreen setup menus.
Functions and settings are arranged into six menus: Picture, Audio, Language, Display, Operation Setting, and Initial
Setup.
The following table lists all the functions and settings, with a brief description and page number where you can find full
details.
Menu
Setting
Description
Page #
59
TV Shape
Select the aspect ratio that matches your TV.
Stretch the picture to fit your TV screen.
Turn HDMI video output on or off.
View Mode
59
HDMI Output Setting
59
Set the component video output to progressive or
interlaced.
Picture
Progressive Setting
HD Resolution
60
60
60
Select the video resolution for the HDMI OUT.
For displaying JPEG images at a high resolution on a
HDTV.
HD JPEG Mode
Video Black Level
Brightness
Choose a video black level.
Adjust the picture brightness.
Adjust the picture sharpness.
60
60
60
Sharpness
Audio
Settings for the digital signal output by the HDMI digi-
tal audio outputs.
Digital/HDMI Audio Out
Linear PCM Out
61
61
61
Select whether or not the DVD receiver down samples
digital audio.
Select a language for the onscreen setup menus and
messages.
On-Screen Language
Language
Disc Menu Language
Audio Language
Select your preferred language for disc menus.
Select your preferred language for soundtracks.
Select your preferred language for subtitles.
Turn on or off onscreen messages and indicators.
61
61
61
63
Subtitle Language
On-Screen Display
Display
Select a color for onscreen setup menus and mes-
sages.
On-Screen Display Color
Background
63
63
Select a background color for when playback is
stopped.
Screen Saver
Parental Lock
Security Code
Set the Screen Saver function.
63
64
64
Set the Parental Lock function.
Operation
Setting
Change the security code for use with parental lock.
Determines what’s played on DVD-Audio discs with
DVD-Video contents.
DVD Priority Contents
SACD Priority Contents
65
65
Determines how the SACD multichannel and 2-chan-
nel area and the CD area are played.
Initial Setup
TV Shape
This menu appears automatically the very first time
you turn on your DVD receiver. (These settings are
available in other menus.)
HDMI Output Setting
On-Screen Language
29
57
DVD Onscreen Setup Menus—Continued
Using the Onscreen Setup Menus
This section explains how to navigate the onscreen setup menus.
Use the Up/Down [ ]/[ ] but-
tons to select the options, and
press the [Enter] button to con-
firm your selection.
3
Input
Enter
Setup
When you’ve finished, press the
[Setup] button again.
4
The onscreen setup menu closes.
Press the Input [ ]/[ ] buttons
to select “DVD”, and then press
the [Setup] button.
1
The onscreen setup menu appears, as
shown.
Picture
TV Shape
: 4:3 Letter box
: Normal
: On
View Mode
HDMI Output Setting
Progressive Setting
HD Resolution
HD JPEG mode
Video Black Level
Brightness
: Progressive
: 480p
: Off
: Light
: 4
Sharpness
: 4
Use the arrow [ ]/[ ]/[ ]/[
]
2
buttons to navigate the menus,
and press the [Enter] button to
see the available options.
58
DVD Onscreen Setup Menus—Continued
View Mode
Picture Menu
With this setting you can adjust the aspect of the picture
so that it fits your TV screen. Due to your TV’s aspect
ratio setting and the DVD’s aspect ratio, black bars may
appear above and below the picture or at the sides and the
aspect of the picture may be unsuitable. In this case, use
this setting to adjust the aspect of the picture as you like.
TV Shape
With this setting you can select a picture format to match
the aspect ratio of your TV.
4:3 Letter box (default):
Choose this option if you have a
standard TV (4:3 aspect ratio).
When you watch widescreen
DVD-Video movies, the entire pic-
ture will be visible and there will be
black bars at the top and bottom of
the screen, as shown.
Normal (default):
The picture is displayed in its original aspect ratio.
View Mode1:
The picture is stretched horizontally to make it fit the
height of the screen.
View Mode2:
The picture is stretched vertically to make it fit the width
of the screen.
4:3 Pan Scan:
Choose this option if you have a
standard TV (4:3 aspect ratio) and
want to use the full height of the
View Mode3:
The picture is stretched horizontally and vertically.
screen when watching widescreen
DVD-Video movies. In order to use
the full height of the screen, the pic-
ture will be cropped on both sides, as shown. This option
won’t work with discs that don’t support pan and scan.
Tip:
The view mode can also be changed by
using the remote controller’s [Aspect]
button.
Note:
16:9 Widescreen:
This setting does not apply to DVD menus.
Choose this option if you have a widescreen TV (16:9
aspect ratio). Depends on TV, the picture appears
stretched when watching programs in 4:3 format.
HDMI Output Setting
With this setting you can turn the HDMI video output on
or off. See page 30 for more information.
16:9 Compressed:
Choose this option if you have
a widescreen TV (16:9 aspect
ratio) and the picture appears
stretched when watching pro-
grams in 4:3 format. This
option will correct the issue.
On (default):
Video is output by the HDMI OUT.
Off:
Video is not output by the HDMI OUT.
Tip:
This setting can also be changed by using the [HDMI]
button on the front panel (see page 30).
Notes:
• This setting does not apply to DVD menus.
• When the HDMI OUT signal is at a resolution of 720p
or 1080i, programs in 4:3 format will appear stretched,
so we recommend that you select the “16:9 Com-
pressed” option.
Note:
When this setting is set to “On”, video is output by the
analog video outputs only when the “HD Resolution” is
set to “480p”.
• With some DVD-Video discs this setting may have no
effect. See the disc’s sleeve notes to see which picture
format is used.
59
DVD Onscreen Setup Menus—Continued
Progressive Setting
HD JPEG Mode
With this setting you can set the component video output
to progressive or interlaced. While the “HDMI Output
Setting” is set to “On”, this setting is fixed at “Progres-
sive” and cannot be changed. See page 30 for more
information.
If your TV is connected to the HDMI OUT and the
HDMI resolution is set to 720p or 1080i, this setting
allows you to display your JPEG pictures in high defini-
tion.
On:
JPEG pictures displayed in high definition.
Interlace:
Component video output is interlaced.
Off (default):
JPEG pictures displayed as normal.
Progressive (default):
Component video output is progressive.
Notes:
Tip:
• If your TV is connected to a video output other than
the HDMI OUT, or the HDMI output resolution is set
to something other than 720p or 1080i, even if this set-
ting is set to “On”, your JPEG pictures will not be dis-
played in high definition.
When the “HDMI Output Setting” is set to “Off”, you
can also change this setting by using the remote control-
ler’s [Resolution] button (see page 30).
HD Resolution
• When using HD JPEG, it may take a while to display
each picture. And the Zoom function cannot be used.
Also, onscreen status messages such as “Play” and
“Stop” are not displayed.
With this setting you can set the video resolution for the
HDMI OUT. See page 30 for more information.
Auto:
The resolution is automatically set to the native resolu-
tion of the TV connected to the HDMI OUT.
Video Black Level
With this setting you can adjust the picture blackness for
the analog video outputs. It does not affect the compo-
nent video output when its set to progressive.
480p (default):
The setting displayed depends on the country in which
you purchased the DVD receiver.
Light:
720 x 480p 60 Hz
Blacks are lighter, and the entire picture becomes lighter.
720p:
1280 x 720p 50/60 Hz
Dark:
Blacks are darker, and the entire picture becomes darker.
1080i:
1920 x 1080i 50/60 Hz
Brightness
Tip:
With this setting you can adjust the picture brightness.
When the “HDMI Output Setting” is set to “On”, you
can also change this setting by using the remote control-
ler’s [Resolution] button (see page 30).
Level 1-7:
“1” is the darkest. “7” is the brightest. The default bright-
ness is “4 (standard)”.
Note:
Initially, the DVD receiver is configured to output both
HDMI and analog video. However, if after changing the
resolution settings there’s no picture, with the analog
video connection or HDMI connection in place, press
the [Resolution] button repeatedly to restore the picture.
Sharpness
With this setting you can adjust the picture sharpness.
Level 1-7:
“1” is the softest. “7” is the sharpest. The default sharp-
ness is “4 (standard)”.
60
DVD Onscreen Setup Menus—Continued
Select “Others” if the language you want is not dis-
played. See “Selecting Other Languages” on page 62.
Audio Menu
Notes:
Digital/HDMI Audio Out
• Not all DVD-Video discs have menus in multiple lan-
guages.
• Even if a DVD-Video disc has menus in multiple lan-
guages, this setting may not always work.
• If a DVD has only one menu language, that will be
used.
With this setting you can configure the HDMI digital
output.
All (default):
Dolby Digital and DTS signals are output as they are.
If your TV or amp doesn’t support higher sampling rates,
set the “Linear PCM Out” setting to “Down Sample On”
(below).
• With some DVD-Video discs you can select languages
from a menu.
PCM:
Dolby Digital and DTS signals are down mixed to 2
channels and output as PCM. If your TV doesn’t support
Dolby Digital and DTS, choose this option. Audio from
speakers connected to DVD receiver is also changed to
PCM.
Audio Language
With this setting you can select your preferred language
for soundtracks. When you play a DVD-Video disc with
multiple language soundtracks, your preferred language
will be selected automatically.
Select “Others” if the language you want is not dis-
played. See “Selecting Other Languages” on page 62.
Note:
MPEG is output as PCM regardless of this setting.
Notes:
Linear PCM Out
• Not all DVD-Video discs have soundtracks in multiple
languages.
With this setting you can configure the DVD receiver to
output digital audio with higher sampling rates (e.g.,
88.2 kHz, 96 kHz) as it is or to down sample it to 48 kHz
or below.
If the TV you connect to the DVD receiver’s HDMI out-
put supports 96 kHz digital audio, select “Down Sample
Off”. Otherwise, select “Down Sample On”.
• Even if a DVD-Video disc has soundtracks in multiple
languages, this setting may not always work.
• If a DVD has only one soundtrack, that will be used.
• With some DVD-Video discs you can select languages
from a menu.
Down Sample On:
Source of 48 kHz or more is down sampled to 48 or
44.1 kHz.
Subtitle Language
With this setting you can select your preferred language
for subtitles. When you play a DVD-Video disc with
multiple language subtitles, your preferred language will
be selected automatically.
Select “No Subtitle” if you don’t want subtitles dis-
played. Select “Others” if the language you want is not
displayed. See “Selecting Other Languages” on page 62.
Down Sample Off (default):
Sources are output as they are.
Notes:
• Some copy-protected DVD-Video discs may use
96 kHz digital audio only for D/A conversion to the
analog audio outputs.
• With some discs, even if you select “Down Sample
Off”, the digital audio will be down sampled, and in
some cases may not be output by the DVD receiver’s
HDMI output.
Notes:
• Not all DVD-Video discs have subtitles.
• Even if a DVD-Video disc has subtitles in multiple
languages, this setting may not always work.
• If a DVD has only one subtitle language, that will be
used.
Language Menu
• With some DVD-Video discs you can select subtitles
from a menu.
On-Screen Language
With this setting you can select a language for the
onscreen setup menus and messages.
Select one of the displayed languages.
Disc Menu Language
With this setting you can select your preferred language
for disc menus. When you play a DVD-Video disc with
multiple language disc menus, your preferred language
will be selected automatically.
61
DVD Onscreen Setup Menus—Continued
■ Selecting Other Languages
This section explains how to select other languages for
disc menus, audio, and subtitles.
Language
Tibetan
Code
BO
BR
CA
CO
CS
CY
DA
DZ
EO
ET
EU
FA
FI
Language
Kirundi
Code
RN
RO
RW
SA
SD
SG
SH
SI
Breton
Romanian
Kinyarwanda
Sanskrit
Sindhi
Catalan
Corsican
Czech
Select “Others” from the “Disc
Menu Language”, “Audio Lan-
guage”, or “Subtitle Language”
1
Remote controller
Welsh
Sangho
Serbo-Croatian
Sinhalese
Slovak
menu, and then press [Enter].
Danish
Bhutani
Esperanto
Estonian
Basque
Persian
SK
SL
Slovenian
Samoan
Shona
Use the Left/Right [ ]/[ ] buttons
to select the code.
2
SM
SN
SO
SQ
SR
SS
ST
SU
SW
TA
Use the Up/Down [ ]/[ ] buttons to
enter a language code.
See adjacent table for language codes.
Finnish
Somali
Fiji
FJ
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Faroese
Frisian
FO
FY
GA
GD
GL
GN
GU
HA
HI
Irish
Scots-Gaelic
Galician
Guarani
Gujarati
Hausa
When you’ve finished, press the
[Enter] button.
3
Telugu
TE
TG
TH
TI
Tajik
Hindi
Thai
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
HR
HU
HY
IA
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
TK
TL
Use this list when specifying other languages.
TN
TO
TR
TS
TT
Language
Japanese
English
Code
JA
Language
Kirghiz
Code
KY
LA
IE
IK
Turkish
Tsonga
Tatar
EN
FR
DE
IT
Latin
Indonesian
Icelandic
Hebrew
Yiddish
IN
French
Lingala
LN
IS
German
Italian
Laothian
Lithuanian
Latvian
LO
LT
IW
JI
Twi
TW
UK
UR
UZ
VI
Ukrainian
Urdu
Spanish
Chinese
Dutch
ES
ZH
NL
PT
SV
RU
KO
EL
LV
Javanese
Georgian
Kazakh
JW
KA
KK
KL
KM
KN
KS
KU
Malagasy
Maori
MG
MI
Uzbek
Vietnamese
Volapük
Wolof
Portuguese
Swedish
Russian
Korean
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NO
OC
OM
OR
PA
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
VO
WO
XH
YO
ZU
Xhosa
Yoruba
Zulu
Greek
Afar
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
Malay
Abkhazian
Afrikaans
Amharic
Arabic
Maltese
Burmese
Nauru
Nepali
Assamese
Aymara
Azerbaijani
Bashkir
Norwegian
Occitan
Oromo
Oriya
Byelorussian
Bulgarian
Bihari
Panjabi
Polish
PL
Pashto, Pushto
Quechua
Rhaeto-Romance
PS
QU
RM
Bislama
Bengali
BN
62
DVD Onscreen Setup Menus—Continued
Display Menu
On-Screen Display
With this setting you can turn on or off onscreen mes-
sages, such as “Play”, “Stop”, and “Resume”.
Off:
Onscreen messages are not displayed.
On (default):
Onscreen messages are displayed.
On-Screen Display Color
With this setting you can set the color and theme of the
Disc navigation window.
Sapphire
Pearl
Amethyst
Garnet
Background
With this setting you can select the color of the back-
ground that’s displayed when the DVD receiver is
stopped.
Blue
Gray
Graphic:
The theme picture specified for the “On-Screen Display
Color” setting is used.
Screen Saver
With the Screen Saver function you can protect your TV
against screen burn-in, which can occur when the same
image or menu is displayed for a long time.
Off:
Screen saver off.
On (default):
Screen saver on.
When the “Screen Saver” function is set to “On”, and
playback is stopped for 15 minutes, the Screen Saver
function automatically displays a moving image.
Once the screen saver has been activated, you can cancel
it by pressing either the Play [ ] button.
63
DVD Onscreen Setup Menus—Continued
• Discs with parental lock may cut certain scenes,
replace certain scenes with children-friendly scenes,
or prevent playback of the entire disc.
Operation Setting Menu
Setting the Parental Lock
With the Parental Lock function you can block access to
certain scenes that the authors have flagged as being
unsuitable for children.
Change the Security Code
To change the Security Code, confirm your existing code
then enter a new one.
Select “Operation Setting” menu
in the setup.
1
Select “Operation Setting” menu
in the setup.
1
Use the Up/Down [ ]/[ ] but-
tons to select “Parental Lock”,
and then press the [Enter] but-
ton.
The password (security code) input
screen appears.
2
Use the Up/Down [ ]/[ ] but-
tons to select “Security Code”,
and then press the [Enter] but-
ton.
The password (security code) input
screen appears.
2
Remote controller
Remote controller
Enter the security code using the
3
Enter the existing security code
3
remote controller’s number but-
tons, and then press the [Enter]
button.
The default security code is “8888”.
You can change the security code in the
next section.
using the remote controller’s
number buttons, and then press
the [Enter] button.
The default security code is “8888”.
Even if a new security code has been
entered, the code “8888” can still be
used.
Once the security code has been
entered, the new security code input
screen appears.
Use the Up/Down [ ]/[ ] but-
4
Enter the new security code
4
tons to change the level of paren-
tal lock, and then press the
[Enter] button.
At level 8 parental lock is off, with level
1 being the strictest level.
using the remote controller’s
number buttons, and then press
the [Enter] button.
The new security code has been set.
Notes:
• When entering a security code, you can use the [CLR]
button to delete the numbers entered so far, if neces-
sary.
• Not all discs use parental lock. See the disc’s sleeve
notes for details.
Note:
If you forget your security code, enter “8888” instead.
“8888” is a security code that can always be used.
64
DVD Onscreen Setup Menus—Continued
DVD Priority Contents
This setting determines what is played when a
DVD-Audio disc also contains DVD-Video material.
DVD-AUDIO (default):
The DVD-Audio material is played.
DVD-VIDEO:
The DVD-Video material is played.
SACD Priority Contents
SACDs have two separate areas for storing audio
tracks—one for multichannel audio, the other for 2-
channel stereo audio. In addition, hybrid SACDs have
an extra layer for playback in standard CD players.
With this setting you can determine how SACDs are
played by the DVD receiver.
2 ch Area (default):
The 2-channel stereo audio tracks are played.
Multi ch Area:
The multichannel audio tracks are played.
CD Area:
The CD layer of hybrid SACDs is played.
Note:
This setting determines which area of the disc is played
initially. If “Multi ch Area” is selected, and an SACD
that contains no multichannel area is loaded, the 2-chan-
nel area will be played.
65
Additional information
Resetting the receiver
Disc Content Organization
Use this procedure to reset all the receiver’s settings to
the factory default.
■ DVD-Video Format
DVD-Video discs contain titles, which are usually sub-
Note that resetting the DVD receiver will delete your
radio presets and custom settings.
divided into chapters.
Title 2
Title 1
Chapter 1
Chapter 2
Chapter 1
Chapter 2
Turn on the DVD receiver.
1
Using the front panel buttons, hold
down the [Stop] button and press
[Standby/On] button.
2
DVD-Video
DVD receiver
“DVD Clear” appears on the display.
When the reset is complete, and the DVD
receiver enters Standby mode.
■ DVD-Audio
DVD-Audio discs contain groups and tracks.
Group 1
Track 2
Group 2
Track 1 Track 2
Track 1
Track 3
HOLD
DVD-Audio
■ SACD
SACDs have two separate areas for storing audio
tracks—one for multichannel audio, the other for 2-
channel stereo audio. In addition, hybrid SACDs have an
extra layer for playback in standard CD players.
DVD-Video regions
Multichannel area
Track 2 Track 3
Stereo area
Track 2 Track 3
Track 1
Track 1
All DVD-Video discs carry a region mark on the case
somewhere that indicates which region(s) of the world
the disc is compatible with. Your DVD receiver also has
a region mark, which you can find on the rear panel.
Discs from incompatible regions will not play in this
receiver. Discs marked “ALL” will play in any player.
The diagram below shows the various DVD regions of
the world.
CD layer of a hybrid SACD
SACD
■ VCD
VCDs contain video tracks.
Track 1
Track 2
Track 3
Track 4
1
5
2
1
Video CD
6
2
3
4
5
■ Audio CD Format
Audio CDs contain tracks.
2
4
Track 1
Track 2
Track 3
Track 4
Track 5
Audio CD
66
Additional information—Continued
■ MP3, WMA & JPEG Files
MP3, WMA and JPEG files are typically organized into
folders. The DVD receiver handles MP3, WMA and
JPEG files as tracks.
ROOT 001
MP3/WMA/JPEG (CD-R/RW, DVD-R/RW,
DVD+R/RW)
Folder 1
Track
001
001.mp3
(001.wma)
010.mp3
(010.wma)
011.mp3
(011.wma)
Folder 2
002
012.mp3
(012.wma)
020.mp3
(020.wma)
004
Glossary
Analog audio
Dolby Digital
An electrical signal that directly represents sound. Com-
pare this to digital audio which can be an electrical sig-
nal, but is an indirect representation of sound. See also
“Digital audio.”
Using a maximum of 5.1 channels of audio, this high
quality surround system is used in many of the finer
movie theaters around the world.
The display shows which channels are active, for exam-
ple showing 3/2.1. The 3 being the two front channels
and the center channel; the 2 being the surround chan-
nels, and the .1 being the LFE channel.
Aspect ratio
The width of a TV screen relative to its height. Conven-
tional TVs are 4:3 (in other words, the screen is almost
square); widescreen models are 16:9 (the screen is
almost twice as wide as it is high).
Down Mix
Down mixing reduces the number of surround-sound
channels and mixes the multi-channel audio that is used
in Dolby Digital and DTS so that the audio matches the
number of speakers and other elements of the output
environment.
Digital audio
An indirect representation of sound by numbers. During
recording, the sound is measured at discrete intervals
(44,100 times a second for CD audio) by an analog-to-
digital converter, generating a stream of numbers.
DRM
On playback, a digital-to-analog converter generates an
analog signal based on these numbers. See also “Sam-
pling frequency” and “Analog audio.”
DRM (digital rights management) is a type of server
software developed to enable secure distribution of paid
content over the web, recently incorporated by WMA
(Windows Media Audio).
DTS
DTS stands for Digital Theater Systems. DTS is a sur-
round system different from Dolby Digital that has
become a popular surround sound format for movies.
67
Glossary—Continued
Dynamic range
NTSC (National Television Standards Committee)
This is one broadcasting system for color televisions,
and is used in the U.S., Korea, Central and South Amer-
ica, Japan, and other countries.The system consists of
525 horizontal scan lines, and is divided into 30 frames
per second. It uses an interlacing method which skips
every other scan line to produce an image (field) with
one-half of the full resolution, and displays 60 such
fields per second.
The difference between the quietest and loudest sounds
possible in an audio signal (without distorting or getting
lost in noise).
Dolby Digital and DTS soundtracks are capable of a very
wide dynamic range, delivering dramatic cinema-like
effects.
File extension
A tag added to the end of a filename to indicate the type
of file. For example, “.mp3” indicates an MP3 file.
PAL (Phase alternation by line)
This is one broadcasting system for color televisions,
and is used primarily in Europe.This system consists of
625 horizontal scan lines. It uses an interlacing method
with 25 frames (50 fields) per second.The vertical reso-
lution is higher than NTSC, however the frame rate is
lower.
HD
Abbreviation for high definition, as in HDTV (high-def-
inition TV).
HDCP (High-bandwidth Digital Content Protection)
The video encryption technology developed by Intel for
HDMI/DVI. It’s designed to protect video content and
requires a HDCP-compatible device to display the
encrypted video.
PBC (PlayBack Control) (Video CD only)
A system of navigating a Video CD through on-screen
menus recorded onto the disc. Especially good for discs
that you would normally not watch from beginning to
end all at once—karaoke discs, for example.
HDMI
HDMI (High-Definition Multimedia Interface) is a high-
speed digital interface which has the capability to sup-
port standard, enhanced, or high-definition video plus
standard to multichannel surround-sound audio on a sin-
gle digital connection. HDMI features include uncom-
pressed digital video, a bandwidth of up to 5 gigabytes
per second and communication between the AV source
and AV devices such as DTVs.
PCM (Pulse Code Modulation)
The most common system of encoding digital audio,
found on CDs and DAT. Excellent quality, but requires a
lot of data compared to formats such as Dolby Digital.
Progressive scan video
All the lines that make up a video picture are updated in
one pass (compared to interlace which takes two passes
to update the whole picture).
ISO 9660 format
International standard for the volume and file structure
of CD-ROM discs.
Regions (DVD-Video only)
These associate discs and players with particular areas of
the world. This unit will only play discs that have com-
patible region codes. You can find the region code of
your unit by looking on the rear panel. Some discs are
compatible with more than one region (or all regions).
JPEG
A file format used for still images, such as photographs
and illustrations. JPEG files are identified by the file
extension “.jpg” or “.JPG”. Most digital cameras use this
format.
Sampling frequency
LFE
The rate at which sound is measured to be turned into
digital audio data. The higher the rate, the better the
sound quality, but the more digital information is gener-
ated. Standard CD audio has a sampling frequency of
44.1kHz, which means 44,100 samples (measurements)
per second. See also “Digital audio.”
LFE refers to the low-frequency effect sounds that are
used in Dolby Digital and DTS. Generally, the subwoof-
ers function more effectively when these sounds are con-
tained in the signal from the disc or other media.
MP3
MP3 (MPEG1 audio layer 3) is a compressed audio file
format. Files are recognized by their file extension
“.mp3” or “.MP3”.
T-D (Theater-Dimensional)
This is a virtual surround-sound technology that was
developed by Onkyo Corporation. For details, see
page 41.
MPEG video
The video format used for Video CDs and DVDs. Video
CD uses the older MPEG-1 standard, while DVD uses
the newer and much better quality MPEG-2 standard.
WMA
WMA is short for Windows Media Audio and refers to
an audio compression technology developed by
Microsoft Corporation. WMA data can be encoded by
using Windows Media Player version 8.
68
Troubleshooting
If you have any trouble using the DVD receiver, look for
a solution in this section. If you can’t resolve the issue
yourself, contact the dealer from whom you purchased
this unit.
Audio
The sound is not heard or very quiet
• Make sure the power cord is plugged into an AC out-
let.
The DVD receiver does not work or shows no reac-
• Make sure that all audio connecting plugs are pushed
in all the way (page 23).
• Make sure that none of the connecting cables are bent,
twisted, or damaged.
tion.
DVD receiver
• Make sure that the speakers are connected correctly
and the speaker cables’core wires touch only the
speaker connectors (page 17).
HOLD
• Check to make sure that the volume level is not set to
minimum (page 31).
Press and hold [Stop] button for 10 seconds to
forcibly shut down the DVD receiver.
• Make sure that the input source is properly selected
(page 31).
Power
• Check to make sure the muting function is not
engaged. If the MUTING indicator is flashing, the
sound is muted. Cancel the muting function (page 32).
• When the headphones are connected, the speakers do
not output any sound. Disconnect the headphones
(page 31).
The power to the system is not turned on
•
Make sure that the power cord is plugged into the AC
outlet. Make sure that the other end of the power cord
is properly connected to the DVD receiver’s AC
INLET (page 23).
• Make sure that the digital input source is assigned
properly (page 56).
• Unplug the power cord from the AC outlet, wait for 10
seconds or more, then plug the cable in again.
• Check the digital audio output setting on the con-
nected device. On some game consoles, such as those
that support DVD, the default setting is off.
• The audio signal input from HDMI IN is not output
from the speakers connected to the DVD receiver.
Make the analog or digital connection (pages 24, 25).
The power is turned off during the operation
• If the SLEEP indicator is lit on the display, the Sleep
timer is functioning. Cancel the Sleep timer (page 32).
• If the Standby indicator is blinking on and off, the
built-in protection circuit is activated. Be careful not
to short the positive and negative wires.
There’s no sound with a certain signal format
• Check the digital audio output setting on the con-
nected device. On some game consoles, such as those
that support DVD, the default setting is off.
The DVD receiver turns off as soon as it’s turned on
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet immedi-
ately. Disconnect all speaker cables and input sources,
and leave the DVD receiver with its power cord dis-
connected for 1 hour. After that, reconnect the power
cord and set the volume to maximum. If the DVD
receiver stays on, set the volume to minimum, discon-
nect the power cord, and reconnect your speakers and
input sources. If the DVD receiver turns off when you
set the volume to maximum, disconnect the power
cord, and contact the dealer from whom you pur-
chased this unit.
Sound is not good
• Make sure that the speaker cords are connected cor-
rectly. Check their polarity (+/ꢁ) (page 17).
• Connect the analog audio cables (RCA) firmly
(page 23).
• Sound quality could be affected by a strong magnetic
field, such as a TV set. Locate such a device far from
the DVD receiver.
• If you have any devices that emit high intensity radio
waves near the DVD receiver, such as a cellular phone
in operation (calling), noise may be generated.
• The DVD receiver uses a rotating unit whose precision
instrument generates faint hissing sound while reading
a disc during playing back or searching a track; you
may hear it in a silent environment.
• Using cable ties to bundle audio cables with power
cord, speaker cables, and so on may degrade the audio
performance, so don’t do it.
69
Troubleshooting—Continued
The subwoofer produces no sound
• When you play source material that contains no infor-
mation in the LFE channel, the subwoofer produces
no sound.
• Make sure the subwoofer is configured correctly
(page 54).
Video
There’s no picture
• Make sure that all video connecting plugs are pushed
in all the way (page 23).
• Make sure that each video component is properly con-
nected. (pages 23-26)
• If the video source is connected to an HDMI IN, your
TV must be connected to the HDMI OUT (page 26).
Your TV input must be changed to HDMI.
• On your TV, make sure that the video input to which
the DVD receiver is connected is selected.
Headphones makes noise or no sound
• There may be a bad contact. Clean up the headphones
terminal. For information on how to clean up, see the
instruction manual attached to the headphones. Other-
wise, verify the cord of the headphones which may be
broken.
Sound Quality
There’s no picture from a source connected to an
HDMI IN
• The TV or display does not support the current video
resolution and you need to select another resolution on
your AV component.
• The sound quality becomes stable when 10 to 30 min-
utes have passed after the power was turned on.
• Using cable ties to bundle audio cables with speaker
cables may degrade the audio performance, so don’t
do it.
There’s no picture to your TV connected to an HDMI
OUT
The Late Night function doesn’t work
• Make sure the source material is Dolby Digital.
•
The HDMI Output Setting is set to Off or your TV
doesn’t support HDMI Resolution settings of 720p
and 1080i (page 30).
The beginning of audio received by an HDMI IN can’t
be heard
• Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio sig-
nals, audio output may not start immediately.
• Try pressing the [HDMI] button on the front panel
repeatedly to switch the HDMI Output Setting to on,
and then pressing the [Resolution] button on the
remote controller repeatedly to get picture (page 30).
• If the DVD receiver is connected to your AV compo-
nent, try connecting it directly to your TV. It will not
work if you connect to a component that doesn’t sup-
port HDCP (page 26).
There’s no sound to your TV connected to an HDMI
OUT
• You won’t hear any sound from the HDMI OUT if
your TV only supports DVI.
• Change the HDMI setting on your TV to HDMI.
• Your TV doesn’t support Dolby or DTS. Change the
“Digital/HDMI Audio Out” setting to “PCM”
(page 61).
• Your TV doesn’t support 88.2 kHz, 96 kHz, 176.4
kHz or 196 kHz PCM. Change the “Linear PCM Out”
setting to “Down Sample On” (page 61).
There’s no picture to your TV connected to an
Component Video Output
• Your TV does not support progressive scanning, and
the HDMI Output Setting is on.
While the HDMI Output Setting is on, the component
video output outputs progressive video.
Try pressing the [HDMI] button on the front panel
repeatedly to switch the HDMI Output Setting to off,
and then pressing the [Resolution] button repeatedly
to switch to Interlaced (page 30).
• Press the [Resolution] button repeatedly to select 480p
(page 30).
There’s no picture to your TV connected to an
Composite Video Output
• Try pressing the [Resolution] button on the remote
controller repeatedly to get picture (page 22).
70
Troubleshooting—Continued
Tuner
Disc Playback
Reception is noisy, FM stereo reception is noisy, or
the FM ST indicator doesn’t appear
• Relocate your antenna.
• Move the DVD receiver away from your TV or com-
puter.
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
The disc won’t play or is automatically ejected after
loading
• Make sure the disc is free from dirt and dust and is not
damaged (page 9).
• Make sure the disc is loaded with the label side face up
and aligned properly in the disc tray guide.
• If the region number on a DVD-Video disc does not
match the number on the receiver, the disc cannot be
used (page 66).
• Condensation inside the receiver: Allow time for con-
densation to evaporate. Avoid using the receiver near
an air-conditioning unit.
• Reload the disc with the label side face up.
• If the Parental Lock function is active, defeat it or
change the level (page 64).
Remote Controller
The remote controller doesn’t work
• Make sure that the batteries are installed with the cor-
rect polarity (page 11).
• Install new batteries. Don’t mix different types of bat-
teries, or old and new batteries (page 11).
The disc doesn’t play in the correct order
• Defeat special playback modes such as Repeat Play,
Memory Playback, and Random Playback
(pages 45–47.)
• Make sure that the remote controller is not too far
away from the DVD receiver, and that there’s no
obstruction between the remote controller and the
DVD receiver’s remote control sensor (page 11).
• Make sure that the DVD receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
• If the DVD receiver is installed in a rack or cabinet
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
• When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
Track numbers cannot be stored when setting
Memory Playback
• Make sure that the disc has been loaded, and the
track(s) you try to program are included on the disc.
It takes a long time until playback starts
• It may take time for the DVD receiver to load and read
a CD or DVD that contains many tracks.
New settings made in the onscreen setup menus
while a disc is playing are ineffective
•
Some settings can be changed while a disc is playing,
but are not effective until the disc is stopped then
restarted: Press the Stop [ ] button, then start play-
back again.
Can’t control a TV
• Make sure you’ve entered the correct remote control
code.
• To control another manufacturer’s TV, point the
remote controller at the component. Be sure to enter
the appropriate remote control code first (page 52).
Screen is stretched or aspect does not change
•
The “TV Shape” setting in the onscreen setup menu
is incorrect. See page 59 for how to set it correctly for
your TV/monitor.
Picture disturbance during playback or the picture is
dark
Can’t control an RI Dock
• This receiver is compatible with Macro-Vision Sys-
tem copy guard. Some discs include a copy prevention
signal, and when this type of disc is played back,
stripes etc., may appear on some sections of the pic-
ture depending on the TV. This is not a malfunction.
• Due to the receiver’s copy protection circuits, connec-
tion of this device through a VCR or an AV selector
may prevent recording or cause picture problems. This
is not a malfunction.
• Make sure that the
cable and analog audio cable
are connected properly. Connecting only an
won’t work (page 25).
• To control an RI Dock that’s connected via
the remote controller at the DVD receiver.
cable
, point
The
functions don’t work
• To use
, you must make an
connection and an
analog audio connection (RCA) between the compo-
nent and DVD receiver, even if they are connected
digitally (page 25).
71
Troubleshooting—Continued
No sound, or sound is distorted
• No sound is output when scanning discs other than
audio CDs and SACDs.
• Check that the disc is free from dust and dirt, and that
it is not damaged (page 9).
Connection with External Devices
No sound is heard from the connected device
• Make sure that the optical digital cable is not bent over
or damaged.
• Set the “Digital/HDMI Audio Out” to “PCM”,
because the TV supports only PCM signals (page 61).
• Check that the plugs and terminals are free of dirt,
oxide, etc. and clean if necessary. Also check the cable
for damage.
The turntable sounds still
• Make sure if the turntable has built in phono equalizer.
• If the turntable has no phono equalizer built in, you
must provide one separately.
Noticeable difference in DVD and CD volume
• This is due to differences in the audio format and is not
a malfunction.
DVD-Audio playback stops
The turntable makes no sound
•
The disc may have been illegally copied.
• If your turntable uses an MC cartridge, you must con-
nect an MC transformer or an MC head amp.
Can’t watch the DVD-Video
•
With some DVD-Video Discs, you need to select an
audio output format from a menu.
The Colors of the TV Picture Bleed
• Locate the speakers far from the TV.
Can’t watch the DVD-Video material on a DVD-Audio
disc
• Set the “DVD Priority Contents” setting to
“DVD-VIDEO” (page 65).
The DVD receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Can’t play the multichannel area of a hybrid SACD
• Set the “SACD Priority Contents” setting to “Multi ch
Area” (page 65).
Can’t play MP3 and JPEG discs
• Use only ISO 9660 Level 2 format discs (page 9).
• The disc has not been finalized. Finalize the disc
(page 9).
Before disconnecting the power cord from the wall out-
let, set the DVD receiver to Standby.
Can’t select MP3 files
• MP3 files without a “.mp3” or “.MP3” filename exten-
sion are not recognized.
• The MP3 disc is a multisession disc. Only files in the
first session of a multisession disc can be played
(page 9).
Can’t play WMA files
• WMA files without a “.wma” or “.WMA” filename
extension are not recognized.
• The WMA file’s copyright option is on. Don’t use the
copyright option (page 9).
Can’t view JPEG files
• JPEG files without a “.jpg” or “.JPG” or “.JPEG” file-
name extension are not recognized.
• The JPEG file is too big. Use JPEG files that are less
than 5 megabytes (page 9).
72
Troubleshooting—Continued
HDMI Status Mode
If you’re using an HDMI connection and there’s no picture or sound, you can check the status of the HDMI connection
by pressing and holding down the DVD receiver’s [Display] button for 10 seconds until a message ID appears on the
display. Look up the message ID in the following tables and check the HDMI connections and settings on both the DVD
receiver and the connected component.
HDMI connection and HDMI-related settings status
Displayed ID
Message
Turn the DVD receiver and the connected component off, then turn them on again. Make sure that
the connected component is working properly and that the DVD receiver’s HDMI settings are con-
figured suitably for that component.
MSG ID 001
MSG ID 015
MSG ID 021
MSG ID 022
MSG ID 023
Input is selected other than DVD or VIDEO1. No output from HDMI OUT.
When the DVD or VIDEO1 input is selected, the “HDMI Output Setting” is set to “Off”. Change it to
“On” (page 30).
Check the settings and connections of the TV and component connected to DVD receiver.
No picture from the HDMI connection
Displayed ID
Message
MSG ID 002
The “HDMI Output Setting” is set to “Off”. Change it to “On” (page 30).
MSG ID 003
MSG ID 004
The HDMI cable may not be connected properly. Check the connection. Also, make sure the HDMI
input on the TV is correctly configured to received HDMI.
Make sure the HDMI input on the TV is correctly configured to received HDMI.
The connected component may not support HDCP. Make sure the connected component supports
HDCP.
Turn the DVD receiver and the connected component off, then turn them on again.
The DVD receiver may be connected to the other component’s DVI jack. Some TVs may not prop-
erly receive the video output by the DVD receiver. Also, with a DVI connection, there will be no
sound.
MSG ID 005
MSG ID 006
MSG ID 007
The DVD receiver’s “HD Resolution” setting is set to “720p” or “1080i”. If your TV doesn’t support
these resolutions, select another resolution (page 30).
MSG ID 008
MSG ID 009
The connected component may not be receiving the HDMI signal properly.
Try selecting another resolution on the DVD receiver (page 30).
No sound from the HDMI connection
Displayed ID
Message
MSG ID 011
MSG ID 014
The connected component may not support 96 kHz PCM. Set the DVD receiver’s “Linear PCM
Out” setting to “Down Sample On” (page 61).
MSG ID 012
MSG ID 013
The connected component may not support Dolby Digital. Set the DVD receiver’s “Digital/HDMI
Audio Out” setting to “PCM” (page 61).
MSG ID 016
MSG ID 017
The connected component may not support DTS. Set the DVD receiver’s “Digital/HDMI Audio Out”
setting to “PCM” (page 61).
MSG ID 020
Audio from SACDs is not output by the HDMI OUT.
73
Specifications
■ Video Inputs
HDMI
Composite
Amplifier Section
IN
Rated output Power (FTC)
VIDEO1, VIDEO2/DOCK
50 watts minimum continuous power per
channel, 6 ohm loads, 2 channels driven at
40 Hz - 20 kHz with a maximum total
harmonic distortion of 0.9 %
■ Video Outputs
HDMI
Component
OUT
OUT
VIDEO OUTPUT
THD (Total Harmonic Distortion)
Composite
0.9% (Power Rated)
0.08% (1 kHz, 1 W)
Input Sensitivity and Impedance
■ Audio Inputs
Digital Inputs
Optical: 1
Coaxial: 1
VIDEO1, VIDEO2/DOCK
200 mV/47 kꢀ (LINE)
20 Hz - 100 kHz/+0 dB - 1.5 dB (Direct
mode)
Frequency Response
Analog Inputs
Signal to Noise Ratio
Speaker Impedance
106 dB (LINE, IHF-A)
■ Audio Outputs
Subwoofer Pre Output
Speaker Outputs
Phones
6
ꢀ
- 16
ꢀ
1
FL, FR
1
Video Section
Signal System
NTSC
■ Control Terminal
Composite Video Output/Impedance
1.0 V (p-p)/75 ꢀ negative sync, RCA
Component Video Output/Impedance
Y: 1.0 V (p-p)/75 ꢀ
PB/PR: 0.7 V (p-p)/75 ꢀ RCA
Component Video Frequency Response
5 Hz - 50 MHz - 3 dB
RS232
1
IR Input/Output
1/1
Specifications and features are subject to change without
notice.
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz
AM Tuning Frequency Range
530 kHz - 1710 kHz
40
Preset Channel
General
Power Supply
Power Consumption
AC 120 V, 60 Hz
118 W
Stand-by Power Consumption
0.4 W
Dimensions (W ꢁ H ꢁ D)
435 ꢁ 90 ꢁ 415 mm
17-1/8" ꢁ 3-9/16" ꢁ 16-5/16"
Weight
8.6 kg (19.0 lbs.)
Operation Condition Temperature and Humidity
5°C–35°C (41°F–95°F), 5%–85%
Disc Compatibility
SACD, DVD-Audio, DVD-Video, DVD-
R/RW (VIDEO), DVD+R/RW, CD, CD-
R/RW, Video CD, MP3, WMA, JPEG
Disc that have not been property finalized
may only be partially playable or not
playable at all
74
Remote Control Codes List
TV
TV
TV
888
0264
0009
Beko
0714
0154
1032
0037
0195
Clarion
Clarivox
0180
0037
Acura
Bell & Howell
BenQ
0092, 0108, 0653,
1150
Commercial
Solutions
Addison
Admiral
Advent
0047, 1447
Beon
0093, 0463
Concerto
Conrac
0056
0808
Blaupunkt
0761, 0783, 0815,
0817, 0842
0556, 1037, 1254,
1314
Blue Sky
0009, 0145, 0156,
0264, 0698, 0753,
1156
Aiko
0092
1916
Conrowa
BPL
0208, 0896
0180
Aiwa
Bradford
Brandt
Contec
Craig
0009, 0180
0161, 0180
0054, 0074
0009, 0030, 0208,
0264, 0361, 0602,
0672, 0702, 0753,
0812, 1935
0109, 0335
0236, 0463, 1935
Akai
Broksonic
Crosley
0009, 0037, 0371,
0698, 1037
Bush
0009, 0037, 0180,
0418, 0672
Crown
Akura
Alba
0264
C-Tech
Caihong
Cailing
Candle
Carnivale
Carver
0896
0009, 0037, 0371
0700, 0843
0672
Crown Mus-
tang
0672
0009, 0817
0748
Albatron
Alfide
0030, 0047, 0054,
0056, 0060, 0093,
0030, 0056, 0186
0030
America Action 0180
Curtis Mathes 0145, 0154, 0166,
0451, 0702, 1147,
1347
0009, 0037, 0171,
0371, 0433
Amstrad
Anam
0054, 0170
0009
Cascade
Cathay
CCE
0009, 0161, 0180,
0250, 0700
CXC
0180
0037
0009, 0030, 0037,
0056, 0092, 0108,
0154, 0170, 0178,
0180, 0451, 0474,
0623, 0634, 0661,
0672, 0700, 0880,
1150, 1661
Anam National 0161, 0250, 0650
0037
Anhua
0051
0009
Celebrity
Celera
0000
Daewoo
Anitech
0765
0009, 0030, 0060,
0092, 0093, 0108,
0178, 0180, 0451,
0474, 1150
Celestial
Centrex
Centurion
CGE
0767
AOC
0780
0037
Dansai
Dayton
Dayu
0037
0074
0009
Aolinpike
0264
0001, 0009, 0051,
0264, 0661, 0817
0661
0748, 0765, 0767,
0879, 1217
Changcheng
Apex Digital
De Graaf
Decca
Dell
0208
Changfei
0009, 0817
Audinac
0180
0037
Changfeng
Changhai
0264, 0753, 0817
0009, 0817
Audiosonic
0037, 0109
1080, 1178
0145, 0511
0587
0092, 0180, 0451,
0623, 0802, 0875
Denon
Denver
Audiovox
0009, 0156, 0264,
0508, 0765, 0767,
0783, 0817, 1156
Changhong
Aventura
Awa
0171
Dick Smith
Electronics
0698
0009
Chengdu
Ching Tai
0009, 0817
Baihe
0009, 0264
0001, 0009, 0661
0343
Digatron
Digital Life
Digitor
Digix
0037
0009, 0092, 0474
Baile
0780
0000, 0009, 0092,
0161, 0180, 0474,
0700, 0843, 1150
Baird
0037, 0698
0880
Chun Yun
Baohuashi
Baosheng
Barco
0264
0009, 0817
0556
Dixi
0009, 0037
0009
Chunfeng
0009, 0264
Dongda
Donghai
DSE
0053, 0108, 0180,
0474, 1150
Chung Hsin
Basic Line
Baur
0009
0009
Chunsun
Cimline
Cinema
Cineral
0009, 0817
0009
0037, 0361, 0512
0180
0698
Baysonic
Beaumark
Dumont
0017
0672
0178
0171, 0178, 0180,
0463, 1034
Durabrand
0092, 0451
0001, 0009, 0208,
0226, 0264, 0661,
0812, 0817
Beijing
0030, 0056, 0060,
0092, 0186, 1935
Citizen
75
Remote Control Codes List—Continued
TV
TV
TV
ECE
0037
Gintai
Go Video
0474, 1150
0886
Huanghaimei
Huanghe
Huanglong
Huangshan
Huanyu
Huaqiang
Huari
0009
Electroband
Electrograph
Electrohome
Elektra
Elin
0000
0009, 0817
0009
1755
0001, 0030, 0037,
0056, 0109, 0154,
0178, 1150, 1378
GoldStar
0463
0009, 0264, 0817
0264, 0817
0264
0017, 1661
0037
0037, 0343, 0360,
0371, 0634
Goodmans
Elta
0009
0145, 0264
0051
Gradiente
Graetz
0053, 0056, 0170
0361, 0714
0154, 0171, 0178,
0180, 0236, 0361,
0463, 0623
Huodateji
Hypson
Hyundai
ICE
Emerson
0037, 0264
0849, 0865
0264, 0371
0074, 0418
Granada
Grandin
0037, 0208
0610, 0865, 0880
Envision
Erres
0030, 0813
0037
0037, 0195, 0556,
0587, 0672, 0706,
1935
Imperial
Grundig
ESA
0171, 0812
0009, 0030, 0161
0009
0001, 0009, 0264,
0661
Imperial Crown
Ether
Grunpy
Haier
0180
Etron
Indiana
Infinity
Innova
Insignia
Inteq
0037
0037, 0508, 0587,
0698, 0896, 1034
Feilang
Feilu
0009
0054
0009, 0817
0264
Haihong
Haiyan
0009
0037
Feiyan
Feiyue
0264, 0817
0178
0171
0009, 0817
Hallmark
0017
0037, 0109, 0335,
0343, 0560
0030, 0056, 0178,
0180
Interfunk
Intervision
IRT
0037, 0361, 0512
0037, 0264
0451, 0698, 1661
0371
Ferguson
Hankook
Fidelity
Finlandia
Finlux
0361
0037, 0361, 0556,
0661, 0808
Hanseatic
0208, 0346
0037, 0346
0009, 0236
0009
ITS
Harman/Kar-
don
0054
ITT
0361
Firstar
JBL
0054
Harvard
Harwa
0180
Firstline
Fisher
JCB
0000
0773
0154, 0208
0455
0009, 0051, 0092,
0156, 0236, 0474
Havermy
HCM
0093
Jean
Flint
0009
Formenti
Fortress
Frontech
0037
Jensen
Jiahua
0761, 0815, 0817
0051
Helios
0865
0093
Hello Kitty
Himitsu
Hinari
0451
0264
JiaLiCai
0009, 0264
0180
0186, 0683, 0809,
0853, 1181
0051, 0208, 0226,
0817
Fujitsu
0009, 0037
0455
Jinfeng
Hisawa
Fujitsu General 0186
Jinque
Jinta
0009, 0264, 0817
0009, 0264
0009, 0145, 0156,
0508, 0556, 0748,
0753, 0780, 1156
Fujitsu Sie-
1163
Hisense
mens
0009, 0037, 0054,
0145, 0156, 0264,
0556, 0698, 0817
0171, 0180, 0264,
0342
Jinxing
Juhua
Funai
0009, 0030, 0056,
0092, 0109, 0145,
0156, 0178, 0186,
0225, 0474, 0508,
1037, 1145, 1150,
1156, 1245, 1256,
1378
Furi
0145, 0264, 0817
0180
0264, 0817
Futuretech
Ganxin
Gateway
Hitachi
0053, 0160, 0371,
0463, 0508, 0606,
0653, 0683, 0731,
1172, 1253
0817
JVC
1755, 1756
0030, 0047, 0051,
0092, 0178, 0180,
0451, 0560, 1347,
1447, 1454
Hitec
0698
0865
GE
Hoeher
0009, 0093, 0264,
0817
Hongmei
GEC
0037
Hongyan
Hua Tun
Huafa
0264, 0817
0009, 1150
0009, 0145
Geloso
General
Gibralter
0009
0186
0017, 0030
76
Remote Control Codes List—Continued
TV
TV
TV
Kaige
Kaisui
Kanghua
0009, 0264, 0817
0009
M & S
0054
Nansheng
0264, 0817
0009, 0037, 0109,
0346, 0480
0051, 0208, 0226,
0508
M Electronic
National
0896
0030, 0054, 0186,
0706, 0780, 0802,
1254, 1454
0009, 0030, 0051,
0053, 0056, 0154,
0156, 0170, 0178,
0186, 0264, 0455,
0474, 0508, 0704,
0817, 1150, 1378,
1456, 1704
0001, 0009, 0264,
0661, 0817
Kangli
Magnavox
Kangyi
Karcher
Kathrein
KEC
0009, 0264
0610
NEC
Manesth
Marantz
Mark
0264
0030, 0037, 0054,
0556, 0704, 0855
0556
0180
0037
Neckermann
NEI
0037, 0556
0037
Kendo
Kenwood
Khind
Kioto
0037
0053, 0698, 0706,
0780
Mastro
0030
Neovia
Netsat
0865
0706, 0896
0054, 0556, 0706
0765, 0767
0037
0009, 0035, 0037,
0208, 0371, 0443
Matsui
0037
NetTV
1755
Matsushita
Maxent
0161, 0250, 0650
KLH
0009, 0092, 0093,
0161, 0178, 1150
1755
0698
0037
KLL
Newave
Meck
0053, 0108, 0150,
0180, 0474, 1150,
1331
Nikkai
0035, 0037, 0264
0030, 0092, 0178
0154
Kolin
Mediator
Nikko
0808, 0880, 1037,
1248
Medion
Noblex
Nokia
Kongque
Konka
Korpel
Kost
0009, 0264, 0817
0037, 0587, 0817
0037
0361, 0480, 0606
0748, 0824
Megapower
Megatron
Meile
0700
Norcent
Nordmende
NTC
0145, 0178
0264, 0817
0109, 0343, 0560
0092
1262, 1483
0009
Koyoda
KTV
0009, 0150, 0154,
0178, 0463, 1037
Memorex
Oceanic
Olevia
Onida
0361
0030, 0180
0009, 0264
0009
Mercury
Mermaid
Metronic
Metz
0001
1144, 1240, 1331
0053, 1253
Kuaile
Kulun
0037
0625
Onwa
0180, 0433
0051, 0208, 0226,
0264, 0661, 0817
Kunlun
0388, 0447, 0746
0030, 0150, 0178
0808
0154, 0166, 0250,
0650
Optimus
Optonica
L&S Electronic 0808
MGA
0093
Leyco
0037, 0264
Micromaxx
Microstar
Midland
0037, 0236, 0443,
0463, 0474, 0880,
1463
0001, 0030, 0037,
0056, 0060, 0108,
0178, 0442, 0474,
0644, 0700, 0714,
0856, 1178, 1265,
1378
0808
Orion
0017, 0047, 0051
LG
0030, 0056, 0093,
0108, 0150, 0154,
0178, 0180, 0236,
0250, 0474, 0512,
0817, 0836, 1150,
1171, 1182, 1250
Osaki
0264, 0474
0037, 0343, 0512,
0556
Otto Versand
Mitsubishi
Liesenk & Tter 0037
Lihua
0817
0009, 0208, 0264,
0371, 0602
Monivision
Motorola
0700, 0843
0093
Local India TV
Local Malaysia
TV
0030, 0056, 0060,
0512
0698
MTC
0136, 0512, 0633,
0790
0009, 0051, 0208,
0226, 0264, 0817
Loewe
Mudan
Logik
0001, 1217
0264, 0817
0056
Multitech
Murphy
Myryad
0009, 0180
0474
Longjiang
Luxman
Luxor
0556
0361
0156, 0178, 0361,
0866
NAD
0047, 0054, 0154,
0156, 0178
LXI
Nanbao
0009, 0264
77
Remote Control Codes List—Continued
TV
TV
TV
Palladium
Palsonic
Panama
0418
0773
0264
Radiola
0037
Scott
0178, 0180, 0236
0030, 0047, 0056,
0154, 0178, 0180
0047, 0054, 0056,
0154, 0156, 0171,
0178
RadioShack
Sears
0000, 0030, 0047,
0060, 0090, 0092,
0178, 0618, 0679,
1047, 1147, 1247,
1347, 1447, 1454,
1547
0037, 0051, 0054,
0161, 0208, 0226,
0250, 0508, 0650,
0896, 1168, 1175,
1177
SEG
0264, 1037, 1163
0180
Panasonic
Semivox
Semp
RCA
0156, 1356
0035
Sentra
Shancha
0009, 0051, 0208,
0226, 0264, 0508,
0698, 0706, 0780,
0817
0264, 0817
0030, 0056, 0154,
0178, 0180
Realistic
Panda
0009, 0208, 0226,
0264, 0817
Shanghai
Shaofeng
Rediffusion
Relisys
Reoc
0361
0145, 0817
Pausa
0009
0865
0009, 0030, 0093,
0256, 0474, 0650,
0787, 0818, 1165,
1193
0030, 0047, 0051,
0060, 0156, 0178,
1347, 1378
0714
Penney
Revox
0037
Sharp
Rex
0264
0030, 0037, 0054,
0056, 0074, 0145,
0178, 0180, 0186,
0463, 0474, 1661
Roadstar
0009, 0264, 0418
Shen Ying
Shencai
0009, 0092, 0474
0009, 0145, 0264
Philco
Philips
0009, 0037, 0698,
0712, 0748, 0817
Rowa
0009, 0093, 0236,
0474, 1150
Sheng Chia
Shenyang
Runco
Ruyi
0017, 0030
0817
0000, 0030, 0037,
0051, 0054, 0056,
0092, 0108, 0178,
0186, 0474, 0556,
0690, 1454, 1483
0009, 0264, 0753,
0817
Saba
0109, 0335, 0343
0610
Sagem
Saige
Saisho
Salora
Sherwood
Siemens
Signet
0009
0009, 0817
0009, 0264
0361
0037, 0195
1262
Phonola
Pilot
0037
0030, 0706
Simpson
SKY
0186
0109, 0166, 0679,
0760, 0866
Pioneer
0009, 0030, 0092,
0093, 0154, 0171,
0178, 0474, 0650,
0700, 1755
0037
0765, 0865, 1262,
1276, 1314, 1341,
1498
Sky Brazil
Skygiant
0880
Sampo
Polaroid
0180
0009, 0037, 0264,
0698, 0748, 0753,
0817
0009, 0030, 0037,
0056, 0060, 0090,
0092, 0154, 0156,
0178, 0208, 0226,
0264, 0474, 0556,
0587, 0618, 0644,
0702, 0766, 0812,
0814, 0817, 1060,
1150
Portland
Prima
0092
Skyworth
0761, 0783, 0815,
0817
Sliding
0865, 0880
0009
Princeton
Prism
0700
Samsung
Songba
Sonitron
Sonoko
Sonolor
Sontec
0051
0208
Profex
0009, 0361
0047, 1347, 1447
0009, 0037
0208
Proscan
0009, 0037, 0264,
0418
Sanjian
Sansei
Sansui
0264
0037
Protech
0451
0000, 0650, 1100,
1167, 1300, 1505,
1651
0001, 0009, 0030,
0056, 0178, 0474,
0644
Sony
0463, 0706, 1935
Proton
0088, 0145, 0154,
0156, 0180, 0208,
0264, 0376, 0424,
0474, 0508, 1150,
1179
Soundesign
Soundwave
0178, 0180, 0186
0037, 0418
Proview
Pulsar
Pye
1498
0017
0037
Sanyo
0051, 0060, 0092,
0156, 0178, 0226,
0474, 1150
Sowa
0051, 0208, 0226,
0264, 0817
Sanyuan
SBR
0009, 0093, 0817
0037
Qingdao
Quasar
Quelle
0051, 0250, 0650
Sceptre
1217
0037, 0074, 0361,
0512
Schaub Lorenz 0361
Schneider
Scotch
0037, 0371, 0394
0178
R-Line
0037
78
Remote Control Codes List—Continued
TV
TV
TV
Squareview
SSS
0171
0180
0009
0180
0056, 0074, 0109,
0335, 0343, 0625,
0702, 0896
0030, 0054, 0056,
0178, 0866, 1156
Wards
Telefunken
Warumaia
Watson
Waycon
Weipai
0661
0037
0156
0009
Standard
Starlite
Teletech
Teleton
Tera
0009
0186
Studio Experi-
ence
0843
0030, 0092, 0474
0767
Tevion
Texla
Sunkai
0865
Westinghouse 0885, 0889, 1282
0780
Superscan
Supra
0093, 0864
0056
White Westing- 0037, 0186, 0463,
0109, 0343, 0560,
0625, 1447
house
0623
0661
Thomson
Thorn
Xenius
Supreme
Susumu
0000
0035, 0037, 0074,
0343, 0361, 0512
0009, 0264, 0698,
0773, 0817
0474
Xiahua
0587, 0748, 0865,
0870, 0871
Thorn-Fergu-
son
SVA
Xianghai
Xiangyang
Xiangyu
Xihu
0009
0343
0264
Swisstec
Sylvania
Symphonic
0880
Tiane
0093, 0817
0056, 0178
0017
0009
0030, 0054, 0171,
1314
TMK
0264, 0817
0009
TNCi
0171, 0180
Xingfu
Tobo
0009, 0264, 0748
0264
0000, 0060, 0092,
0093, 0178, 0451,
0474
Xinghai
Xoro
0264
Tongguang
Tongtel
Tophouse
Synco
1217
0780
Yamaha
Yapshe
Yingge
Yoko
0030
Syntax
Sysline
T+A
1144, 1240, 1331
0037
0180
0250
0009, 0035, 0060,
0093, 0145, 0154,
0156, 0161, 0264,
0508, 0509, 0618,
0644, 0650, 0845,
1150, 1156, 1169,
1173, 1256, 1265,
1356, 1456, 1508,
1656, 1704, 1935
0009
0447
0037, 0264
0009
0009, 0092, 0178,
0474, 1150
Tacico
Yonggu
Youlanasi
Yousida
Yuhang
Toshiba
0817
Tai Yi
0009, 1150
0009, 0817
0093
0009
Taishan
Tandy
0009
0017, 0092, 0178,
0463, 1265
Tashiko
0092, 0650, 1150
Zenith
TRANS-conti-
nents
0865
0009, 0037, 0051,
0054, 0060, 0154,
0156, 0474, 1150,
1156, 1254, 1756
ZhuHai
Zonda
0009
0698
Tatung
Transonic
0587, 0698, 0712
0009, 0030, 0092,
0474
Tuntex
TCL
0698, 0706
0808
TV/DVD Combination
TVS
0463
TCM
Akai
1935
0037, 0074, 0264,
0346, 0474
0009, 0037, 0264,
0418, 0455, 0698,
0706, 0712, 1037,
1755
Universum
Broksonic
Bush
1935
Teac
V7 Videoseven 1755
0698, 1037
1935
Vector
Research
Citizen
Denver
Grundig
Sansui
Toshiba
Transonic
0030
Technics
0051, 0250, 0650
0714
0587
Vestel
0037
Technisson
Techview
Techwood
1935
0053, 0160, 0250,
0376, 0650, 0653
0847
1935
Victor
0051, 0056, 1163
1935
Videocon
Vidikron
Vidtech
0037, 0508
0054
0009, 0051, 0092,
0093, 0178, 0264,
0474, 0653
0587
Teco
0178
0054, 0056, 0060,
0092, 0150, 0180,
0186
0857, 0864, 0885,
1755
Viewsonic
Teknika
Teleavia
Vizio
0864, 0885, 1756
0178
0343
Voxson
79
Integra Division of
ONKYO U.S.A. CORPORATION
18 park Way, Upper Saddle River, N.J. 07458, U.S.A.
E
n
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
Y0710-1
SN 29344561
(C) Copyright 2007 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 5 6 1 *
|