LTC 0435 & LTC 0455
Installation Manual
Installatiehandleiding
Digital Color Cameras
Digitale Kleurencamera
EN
FR
DE
ES
NL
IT
Manuel d’installation
Caméra Numérique
Couleur
Manuale d’installazione
Videocamera Digitale a Colori
Installationsanleitung
Manual de Instruções
Digitale Farbkamera
Câmara Digital Colorida
PT
ZH
Manual de instalación
Cámara Digitale de Color
LTC 0435 & LTC 0455 | Installation Manual
EN | 2
7. Do not defeat the purpose of a polarized or grounded mains plug.
A polarized plug has dissimilar prongs (one wider than the other)
to ensure correct polarity, while a grounded plug has an
additional 'ground' prong provided for your safety. If the plug
supplied with the apparatus does not fit into your outlet, consult
an electrician for advice.
8. Protect the power-supply cord from being walked on or pinched,
particularly close to plugs, receptacles and the point where it exits
from the apparatus.
9. Only use attachments and accessories (including stands, tripods,
mounting brackets and housings) specified or recommended by
the manufacturer.
10. Unplug the apparatus during lightning storms and when unused
for extended periods.
11. Do not attempt to service this unit yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
12. Servicing is required when the apparatus does not function in the
normal way, has been dropped, if liquid has been spilled on it, or
if it has been exposed to rain or water. Unplug the unit from the
outlet and refer servicing to qualified service personnel.
13. An all-pole mains switch with contact separation of at least 3 mm
in each pole shall be incorporated in the electrical installation of
the building.
EN
WARNING
To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture.
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 3
FCC INFORMATION
CAUTION
Any changes or modifications to construction of this
device that are not expressly approved by the party
responsible for compliance could void the userfs authority
to operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 4
SPECIFICATIONS
LTC 0435/x0
LTC 0455/x1
Standard resolution
High resolution
Standard
PAL
NTSC
PAL
752 x 582
NTSC
768 x 494
Active pixels (H x V)
Imager
512 x 582
512 x 492
1/3" interline CCD
330 TV lines 540 TV lines
Resolution
Minimum illumination
<0.39 lux
NA
<0.65 lux
<0.26 lux with Nightsense™
Signal-to-noise ratio
Video output
> 50 dB
1 Vpp, 75Ω
Y/C output
Y: 1 Vpp, 75 Ω
C: 0.3 Vpp 75 Ω
Synchronization
Shutter
Internal or Line-Lock (selectable)
Auto / Flickerless / Off (selectable)
PAL: 1/50 - 1/125000 - NTSC: 1/60 - 1/150000
Nightsense™
NA
Auto / Forced / Off
(selectable)
Autoblack
AGC
On / Off (selectable)
On (0-21 dB)/ Off (0 dB) (selectable)
On / Off (selectable)
BLC
ATW
Auto 2500 to 9000 K (with 'Hold' mode)
C and CS compatible
Lens mount
ALC
Video-iris or DC-iris (auto detect)
Power supply
LTC 04x5/1x & /2x: 12 to 28 VAC or 11 to 36 VDC
LTC 04x5/5x & /6x:
<4 W
to 2 VAC
Power consumption
Dimensions (HxWxL)
Weight
58 x 66 x 122 mm (2.28 x 2.6 x 4.8 inch without lens)
450 g (0.99 lbs) (without lens)
Camera mount
Two 1/4" 20 UNC - isolated (bottom) and non-isolated
(top)
Operating temperature
Controls
-20ºC to +50ºC (-4ºF to +122ºF)
On-screen display (OSD) with softkey controls
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 5
Type number overview
Low voltage
High voltage
PAL (Europe) NTSC (USA) PAL (Europe) NTSC (USA)
LTC 0435/10 LTC 0435/20 LTC 0435/50 LTC 0435/60
LTC 0455/11 LTC 0455/21 LTC 0455/51 LTC 0455/61
Standard resolution
High resolution
UNPACKING
Unpack carefully and handle the equipment with care. The
packaging contains:
•
•
•
•
Camera
CCD protection cap
Spare lens connector (male)
These Instructions
Note:
If equipment appears to have been damaged during shipment, repack
it in the original packaging and notify the shipping agent or supplier.
CONNECTION
Power
LTC 04x5/1x and /2x
LTC 04x5/5x and /6x
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 6
To open the quick-connect, push in on the tabs. Connections are not
polarity sensitive Use stranded or solid wire AWG16 to AWG22, cut
back 10mm (0.4") of insulation.
Composite Video
Y/C output (LTC 0455/x1 only)
Pin Y/C Socket
1
2
3
4
GND Y
GND C
Y
C
LENS MOUNTING
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 7
Pin
1
Video iris lens
DC iris lens
Damp-
Supply (11 V, 50 mA max.)
Not used
2
Damp+
Drive+
3
Video signal 1 Vpp, 1 kΩ
Ground
4
Drive-
•
Video-iris and DC-iris lenses are recommended for the best
picture performance.
•
•
The camera automatically detects the type of lens used, and
optimizes performance accordingly.
A spare male lens connector is provided if required.
CAUTION
•
To avoid damaging the CCD sensor when using a C-
mount lens, turn the 'green' back-focus ring counter
clockwise until it stops ('Back focus adjustment')
before mounting the lens.
•
Lenses weighing more than 0.5 kg (1.1lbs) must be
separately supported.
Note:
If a short circuit is detected on the lens connector, the on-screen
display (OSD) failure message 'LENS SHORT CIRCUIT' is shown.
The lens circuit is automatically disabled to avoid internal damage.
Remove the lens connector and check the pin connections.
Back focus adjustment
•
Camera accepts both C and CS-
mount lenses.
1. Unlock the back focus locking
button.
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 8
2. Turn the back focus adjustment as required. (See Note 1).
3. Lock the back focus locking button.
Notes:
1. To optimize picture sharpness in
both bright and low-level lighting, it
is recommended to adjust the back
focus when carrying out the set-up
procedure. The camera's unique
'Lens Wizard' allows focusing at
maximum lens opening to ensure that the object of interest
always remains in focus.
2. When back focusing vari-focus lenses, it must be possible to
obtain a sharp picture in both wide-angle and tele positions, and
for both far and near focus.
3. When back focusing zoom lenses, ensure the object of interest
remains in focus throughout the entire zoom range of the lens.
(See Advanced Set up).
CAUTION
Do not point the camera/lens into direct sunlight. When
viewing an outdoor scene, a video- or DC-iris lens is
recommended.
MOUNTING THE CAMERA
The camera can be mounted from
the top or bottom.
Note:
The BOTTOM mounting is
isolated from ground.
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 9
ADVANCED SET-UP
The camera will normally give an optimal picture without the need
for further adjustments. However for special circumstances advanced
set up options are available.
Hints for menu navigation
How to use the 5 keys
Up key
Menu/select key
Right key
Left key
Lock
Down key
•
•
Press the menu/select key to access the menus or to move to the
next or previous menu.
Press the menu/select key for approximately 1.5 seconds to open
the Installer menu.
•
•
Use the up or down keys to scroll up or down through a menu.
Use the left or right keys to move through options or to set
parameters.
•
•
When in a menu, quickly pressing the menu/select key twice
restores the selected item to its factory default.
To close all menus at once from any menu, select the Exit item
and hold down the menu/select key until the menu display
disappears.
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 10
Menu Navigation
Press the menu
button
MAIN MENU
SHUT/AGC MENU
LEVEL
0
SHUTTER
AGC
AES
ON
ON
OFF
SHUT/AGC
BLC
OFF
COLOR
SYNC
VPHASE
ATW
LINE LOCK
0¡
AUTOBLACK
NIGHTSENSE
EXIT
EXIT
Shutter/AGC Menu
Main Menu
COLOR MENU
WHITE BAL
RED-GAIN
BLUE-GAIN
ATW
0
0
EXIT
Color Menu
Press the menu button
for more than 5sec.
LENS WIZARD
DETECTED LENS
DCIRIS
Lens Wizard Menus
INSTALLER
SET BACK FOCUS NOW
VERSION
00.0010.XX
LENS
AUTO
FAST
SPEED
LENS WIZARD
EXIT
WIZARD
COAX COMM
ON
DETECTED LENS
VIDEO
DEFAULTS
SET BACK FOCUS NOW
EXIT
SET LVL
Installer Menu
EXIT
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 11
Main menu
Function
LEVEL
Selection
Description
-15 - 0 - +15
Adjusts video level.
SHUT/AGC
BLC
Select next menu Shutter / Automatic Gain Control menu.
ON
When 'ON', the level is optimized at the center
of the screen. Parts outside the center may be
under- or over-exposed (this is normal).
OFF
COLOR*
SYNC
ATW
Select to access the color menu. (See Color
menu for detailed explanation).
ATB HOLD
Select next menu
LINE LOCK
INTERNAL
Select 'LINE LOCK' to synchronize with the
power supply frequency. Select 'INTERNAL'
for use with internal synchronization
(automatically selected with DC supply).
V PHASE
EXIT
0-358º
Adjusts the vertical phase offset (when in
'LINE LOCK' mode).
Exit the menu.
*Note:
If the camera (LTC 0455/x1 only) is in black & white high sensitivity
mode (via NightSense™), the color settings and color menu are not
accessible. The NightSense™ sensitivity boost must be selected OFF
to make color adjustments.
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 12
Shutter/AGC menu
Function
Selection
AES
Description
SHUTTER
(AES) Auto-shutter sets the optimum shutter
speed FL for manual iris lenses. (FL)
Flickerless mode avoids OFF interference from
light sources (recommended for use with
video-iris or DC-iris lenses only).
AGC
ON/OFF
ON/OFF
Automatic gain control
AUTOBLACK
Autoblack automatically increases the visibility
of details.
NIGHTSENSE
AUTO
FORCED
OFF
Nightsense™* extends the low-light
performance of the camera. AUTO mode, the
camera automatically inches to monochrome in
low-light conditions. Forced mode, the picture
remains a high-sensitivity monochrome image.
Some active noise or white spots may appear
in the picture.
EXIT
Exit the menu.
*Note:
NightSense™ is only available on the LTC 0455/x1 cameras.
Color Menu
Function
Selection
Description
WHITE BAL
ATW
AWB HOLD
ATW: Auto tracking white balance allows the
camera to automatically adjust for optimal
color reproduction.
AWB HOLD: Puts the ATW on hold and
preserves the color settings.
RED- GAIN*
BLUE- GAIN*
EXIT
-5 - 0 - +5
-5 - 0 - +5
Offset factory white point alignment (reducing
red introduces more cyan).
Offset factory white point alignment (reducing
blue introduces more yellow).
Exit the menu.
*Note:
For special scene conditions only, it will be necessary to change the
white point offsets.
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 13
Accessing installer menu
•
To access the installer menu, press and hold the menu/select key
for five seconds.
Installer menu
Function
Selection
Description
VERSION
Read-only firmware release number (for
service purposes).
LENS
AUTO
FAST
Automatically detect lens type.
A different lens type can be selected.
SPEED
Selects the response time of DC-iris lenses.
Some lenses require slow lens control to avoid
overshoots.
WIZARD
Access the lens wizard menu.
COAX COM
DEFAULTS
ON/OFF
If OFF Bilinx™ communication is disabled
Select next menu Return all set-up settings to
factory defaults.
EXIT
Exit the menu.
Lens wizard menu
Function
Description
SET BACK FOCUS NOW Back focus the lens (see 'Back focus adjustment'). The
scene is focused at maximum lens opening to ensure
that the object of interest remains in focus in bright and
low-light conditions.
SET LVL
When a Video-iris lens is detected, a level
potentiometer is displayed to obtain the best picture
performance. The lens wizard includes a level detector
meter that must be set to the center using the
potentiometer for best results.
EXIT
Exit the menu.
Bosch Security Systems | 2004-12 | Version 3
LTC 0435 & LTC 0455 | Installation Manual
EN | 14
Adjustment procedure DC-iris Lens:
1. Unlock the back focus locking button.
2. Access the "Lens Wizard" menu.
3. The "SET BACK FOCUS NOW" option is highlighted in the
menu.
4. Turn the back focus adjustment as required.
5. Lock the back focus locking button.
6. Exit the menu.
Adjustment procedure Manual-iris Lens:
1. Unlock the back focus locking button.
2. Adjust the lens to the maximum lens opening.
3. Turn the back focus adjustment as required.
4. Lock the back focus locking button.
Adjustment procedure Video-iris Lens:
1. Unlock the back focus locking button.
2. Access the "Lens Wizard" menu.
3. The "SET BACK FOCUS NOW" option is highlighted in the
menu.
4. Turn the back focus adjustment as required.
5. Select the "SET LVL" option in the menu, and the LEVEL bar
appears.
6. Adjust the level potentiometer located on the lens until the
LEVEL bar is in the central position.
7. Lock the back focus locking button.
8. Exit the menu.
Bosch Security Systems | 2004-12 | Version 3
Bosch Sicherheitssysteme GmbH
Ludwig-Bölkow-Allee
Bosch Security Systems B.V.
P.O. Box 80002
85521 Ottobrunn
5600 JB Eindhoven
Germany
The Netherlands
3122 165 23071 04-05
© 2003 Bosch Security Systems B.V.
Subject to change Printed in Portugal
|