OPERATING INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MODE D’EMPLOI
CDC-X927M
YUC
STEREO CAR CD RECEIVER
RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA
AUTOMOVIL
ENGLISH
ESPAÑOL
FRANÇAIS
OWNER’S RECORD
For your convenience, record the model number and
serial number (you will find them on the bottom side of
your set) in the space provided below. Please refer to
them when you contact your AIWA dealer in case of
difficulty.
Model No. CDC-X927M
Serial No.
8C-KC4-901-01
020131ATM-OX
Adjusting the volume
THEFT PROTECTION
(Retractable Front Panel)
1
Turn AUDIO CONTROL.
When your car’s ignition switch is turned off, the front
panel will be retracted automatically as if there were no
car audio in the console.
When the ignition switch is set to ACC or ON position,
the front panel will appear automatically.
VOL (volume) indication appears.
Muting the sound
1
Press PWR/MUTE briefly.
MUTE indicator flashes.
To restore volume, briefly press PWR/MUTE again.
Note
Do not touch and put excessive pressure on the front
panel while it is rotating.
Adjusting sound
You can select the following modes for adjusting sound
depending on the music you listen to: BASS (low
frequencies), TRE (high frequencies), BAL (left/right),
FAD (front/rear), H-BASS (high bass)*, DSSA (Drivers
Sound Stage Adjustment)** and BBE***.
BASIC OPERATION,
AUDIO AND CLOCK
ADJUSTMENT
*
You can reinforce the bass sound.
** Youcanadjustsoundstageandtonebalancetobest
serve a particular seat in the car.
AUDIO CONTROL
TUNE
EJECT
*** Youcanenhancetheclarityofhigh-frequencysound.
1
Press SEL repeatedly to select the mode to be
adjusted.
Pressing SEL cycles through the modes. The
selected mode’s indicator appears.
Turn AUDIO CONTROL to increase or decrease
the level for the selected mode (except for H-BASS,
DSSA and BBE).
SEL DISP
PWR/MUTE BAND
SRC
2
InH-BASSmode, turnAUDIOCONTROL toselect
1, 2, 3, or OFF.
In DSSA mode, turn AUDIO CONTROL to select L
(for the front left seat), R (for the front right seat), or
OFF.
Turning the unit on/off
• You can turn the unit on by pressing any button on the
front panel except z. The unit also turns on when you
press z and insert a CD.
• Press and hold PWR/MUTE until the unit turns off.
In BBE mode, turn AUDIO CONTROL to select 1,
2, or OFF.
Note
Notes
Most operations described in this manual require
theunittobeturnedonbeforestartingtheoperation,
unless explicitly stated otherwise.
• Adjust the level or select an item within 5 seconds, or
the selected mode will return to previous state.
• WhenDSSAisactivated,youcannotadjustBAL,FAD,
BASS, TRE and BBE.
• When BBE sound is activated, you cannot adjust
BASS and TRE.
Changing the source mode
1
Press SRC.
Pressing SRC cycles through source modes in the
following order:
Aligning the source levels
(Source Level Adjuster)
Volume may vary each time you change the source
mode. In this case, you can align each source mode’s
volume to almost the same level.
*
To select another bands, press BAND to select F2,
F3, A1, A2, while “F1” is displayed.
1
2
PressSRCrepeatedlytoselectthedesiredmode.
Press DISP while pressing SEL.
** “DISC” does not appear on the display when there is
no CD in the unit.
***CD Changer Play mode (available when an optional
CD Changer is connected)
“LEVEL 0” appears on the display.
3
Turn AUDIO CONTROL to adjust the level.
Note
Adjust the level within 5 seconds, or this function will be
canceled.
ENGLISH 2
1
2
Press BAND repeatedly to select the desired band
(F1, F2, F3, A1 or A2).
Restoring the factory settings
1
2
Turn off the unit.
Press TUNEi (to move to higher frequencies) or
TUNEk (to move to lower frequencies) to tune in to
a station.
PressandholdDISPuntil“LEVEL--”appearsonthe
display.
“ST” appears on the display when an FM station is
broadcasting in stereo, and receiving conditions are
good.
Seek Tuning and Manual Tuning
• Press and hold TUNEi or TUNEk until Seek
Tuning starts.
Note
YoucanrestorethefactorysettingsonlyforVOL,BASS,
TRE, BAL, FAD, H-BASS, DSSA and BBE as well as
aligned source volume levels.
The unit locates a station automatically (Seek
Tuning).
Setting the beep tone
1
2
Turn off the unit.
• Press
iorTUNEkrepeatedlytosearchfor
TUNE
Press and hold SEL until “BEEP” appears on the
display.
a desired station while increasing or decreasing
the frequency step by step (Manual Tuning).
To stop Seek Tuning, press TUNEi or TUNEk
again.
3
4
TurnAUDIOCONTROLtoselect“ON”or“OFF”.
Press SEL.
The unit turns off.
Monaural mode
When FM signals become weak, or FM reception
becomes poor, the unit automatically switches to
Monaural mode to reduce noise.
Setting the clock
1
2
3
Press and hold DISP until the clock indicator
flashes on the display.
Note
Press TUNEi (to set hour) or TUNEk (to set
minute) and turn AUDIO CONTROL.
Press DISP.
When stereo sound is received, you can also press ST
and select “MONO ON” to listen in manaural mode.
To resume stereo sound receiving, press ST to “MONO
OFF”.
Displaying the clock
Local mode
Local mode allows you to tune in only to strong stations
during Seek Tuning.
1
Press DISP.
To return to the former display, press DISP again.
1
Press LO before you start seek tuning.
“LO” appears on the display.
To return to Distant mode, press LO again.
“LO” disappears and the unit tunes in to all receivable
stations.
RADIO OPERATION
Tuning in to a station
(Seek/Manual Tuning)
Using preset stations
You must preset stations before you can tune in to a
station using preset station number buttons.
TUNE
TUNE
BAND
ST LO SRC
Stereo indicator
Band indicator*
BAND
PS/A.ME SRC
Preset station
buttons 1 – 6
Preset station number
Local indicator
Frequency indication
* “F” means FM, and “A” means AM.
3 ENGLISH
Presetting stations automatically
(Auto Memory)
CD PLAYER OPERATION
Playing a CD
1
Press BAND repeatedly to select the desired band
(F1, F2, F3, A1 or A2).
You can play CDs, CD-Rs and CD-RWs using the
procedure described below.
2
Press and hold PS/A.ME until automatic presetting
starts. “A MEM” appears on the display.
The unit automatically stores up to 6 stations for
each band.
EJECT
After completion of automatic presetting, the unit
tunes in to all the stations stored on the preset
station buttons in order (Preset Scan).
Tocancelautomaticpresetting,pressPS/A.MEagain.
INT
RNDM
REP1
SRC
Checking the preset stations (Preset Scan)
1
Press PS/A.ME briefly.
Each preset station will be tuned in for 5 seconds in
order.
1
2
Press z to open the front panel.
Insert a CD.
To cancel Preset Scan, press PS/A.ME again or any
preset station button.
The front panel will be closed automatically and
“CD” appears on the display.
CD play starts.
If a CD is already inserted, press SRC repeatedly to
select CD play mode.
In normal play, when the last track finishes, the unit
returns to the first track and continues to play.
Presetting stations manually
(Manual Memory)
1
2
3
Press BAND repeatedly to select the desired band
(F1, F2, F3, A1 or A2).
Press TUNEi or TUNEk to tune in to a desired
station (see “Tuning in to a station,” page 3).
Pressandholdthedesiredpresetstationbuttonuntil
the unit beeps.
Labeled-side up
Note
A newly preset station replaces the station on the same
band that was previously stored on that preset station
button.
CD indicator
Elapsed playing time
Tuning in to a preset station
1
2
Press BAND repeatedly to select the desired band
(F1, F2, F3, A1 or A2).
Track number
Press the preset station button on which the desired
station is stored.
To
Press
z*
Eject a CD
Skip to the next track
t
r
Active tuning reception control (ATRC)
The unit automatically suppresses FM noise caused by
vehicle movement, and maintains sound quality.
Go back to the beginning
of the current track
Each extra press skips
backward one extra track
Locate a specific point in Press and hold r or
a track
t until you find the
point.
* When you remove the CD, the front panel will be
closed automatically after a while.
To close the front panel manually, press z while the
front panel is open.
ENGLISH 4
1
2
Connectacassette/MD/MP3portableplayerorother
equipment via the unit’s AUX IN jack (3.5 mm dia.).
PressSRCrepeatedlyuntil“AUXIN”appearsonthe
display.
Notes
• When you play a CD that is already inserted, CD play
starts at the point where it stopped the previous time.
A newly inserted CD starts from the first track.
• A CD-R or CD-RW may take some time to start playing
back, but this is not a malfunction.
Note
WhenaconnectingcordispluggedintotheAUXINjack,
you cannot insert or eject a CD even if you press z. Be
sure to disconnect the cord before inserting or ejecting
the CD. Likewise, be sure to disconnect it before you
turn off the ignition switch, otherwise the front panel
won’t be retracted.
• If a CD-R or CD-RW with no data or incompatible data
is inserted, “ERROR03” will appear on the display.
(See the section “TROUBLESHOOTING”.) The unit
cannot play such discs.
Intro Play
You can locate a desired track by monitoring the first 10
seconds of all the tracks on a CD.
1
Press INT during CD play.
“SCAN” appears on the display.
OTHER FUNCTIONS
2
Press INT again when the desired track is played.
The unit returns to normal CD play.
AUDIO CONTROL
TUNE
One Track Repeat Play
You can play a track repeatedly.
1
Press REP1 during CD play.
“REP1” appears on the display.
To cancel One Track Repeat Play, press REP1 again.
SEL
SRC
Random Play
You can play all the tracks in random order.
Changing the display contrast
1
Press RNDM during CD play.
“RANDOM” appears on the display.
1
2
Press and hold SRC until “CONT.” appears on the
display.
To cancel Random Play, press RNDM again.
Turn AUDIO CONTROL to adjust the contrast.
Note
During Random Play, pressing r allows you to skip
only to the beginning of the current track, not to the
previous track.
Changing the key illumination color
Youcanchooseblueorredasthekeyilluminationcolor.
1
2
3
Press and hold SRC until “CONT.” appears on the
display.
PressTUNEi or TUNEk until “ILL” appears on the
display.
AUXILIARY EQUIPMENT
Turn AUDIO CONTROL to select 1 (for blue) or 2
(for red).
Listening to a cassette/MD/MP3
portable player or other equipment
Setting the dimmer of the display
Youcanlistentomusicthroughequipmentconnectedto
the unit. Refer to the operating instructions for the
correspondingequipmentformoredetailedinformation.
Be sure to remove any loaded CD to prevent possible
damage to the unit before connecting the equipment.
1
2
Press and hold SEL until “DIMMER” appears on the
display.
Turn AUDIO CONTROL to select 0 (bright) or
1 (dimmed).
SRC
AUX IN jack
5 ENGLISH
Replacing the battery
CARD REMOTE
CONTROL
1
Insert the tip of a pointed object A into the hole B
and pull out the battery holder to remove the lithium
battery (CR2025).
Names of parts
Remote control (back)
BAND
TAPE
CD-CH
CD
SKIP
REW
FF
TUNING / DISC
UP
DOWN
Battery holder
VOLUME
2
Install a new lithium battery (CR2025) with the )
side facing up in the battery holder.
1 BAND button
2 TAPE button (This button is not available with this
unit.)
3 CD button
4 CD-CH button (CD changer only)
5 SKIP f/REW button
6 SKIP g/FF button
3
Push the battery holder into the unit until it clicks.
7 PS (preset) button
8 TUNING/DISC UP/DOWN buttons
9 VOLUME +/- buttons
Preparations
A lithium battery is installed in the remote control at the
factory.
Before you use the remote control, be sure to remove
the insulating sheet by simply pulling it out.
CAUTIONS
• Keep the lithium battery out of the reach of children. If
swallowed, consult a doctor immediately.
• To prevent a short circuit, never pinch the battery with
pliers, etc.
Remote control (back)
Insulating sheet
ENGLISH 6
One Disc Repeat Play
You can play all tracks on a disc repeatedly.
CD CHANGER OPERATION
1
Press REP during CD Changer play.
“REP” appears on the display.
Playing a CD
To cancel Repeat Play, press REP again.
YoucanplayCDsfromaconnectedAIWACDChanger.
For detailed information on installing a CD Changer,
refertotheInstallationandConnectionmanualsupplied
with the CD Changer.
One Track Repeat Play
You can play a track repeatedly.
1
Press REP1 during CD Changer play.
“REP1” appears on the display.
RNDM
To cancel Repeat Play, press REP1 again.
One Disc Random Play
You can play all the tracks on a disc in random order.
1
Press RNDM during CD Changer play.
“RANDOM” appears on the display.
To cancel Random Play, press RNDM again.
INT REP1
REP
SRC
DISC
Note
During Random Play, pressing r allows you to skip
only to the beginning of the current track, not to the
previous track.
1
Press SRC repeatedly to display “CD-CH.”
The CD Changer play starts.
CD Changer indicator
Track number
TROUBLESHOOTING
Error code
In the following cases the corresponding error code
indication appears. Follow the suggestions below to
solve such problems. If the error code indication does
not disappear, consult an AIWA service center.
CD number
To
Press
t
Skip to the next track
ERROR01 The disc magazine is not properly inserted
in the CD Changer. Reinsert the magazine.
Refer to the instruction manual for the CD
Changer.
ERROR02 No CDs are loaded in the disc magazine.
Insert CDs properly. Refer to the instruction
manual for the CD Changer.
ERROR03 Focus error. Check that the CD is loaded
properly (right side up, etc.), and the CD
contains valid data.
Skip back to the beginning of
the current track or to the
previous track
r
Advance rapidly to locate a
desired point
Press and hold t,
then release it at the
desired point
Reverse rapidly to locate a
desired point
Press and hold r,
then release it at the
desired point
Start CD Changer play from DISCN
ERROR04 Problem with the CD Changer. Reset the
unitbypressingtheresetbutton. Ifthisdoes
not solve the problem, consult an AIWA
service center.
the first track on the next disc
Start CD Changer play from DISCM
the first track on the previous
disc
Intro Play
You can locate a desired track by monitoring the first 10
secondsofallthetracksontheCDsinthediscmagazine.
1
Press INT during CD Changer play.
“SCAN” appears on the display.
2
Press INT again when the desired track is played.
The unit returns to normal CD play.
7 ENGLISH
Reset button
GENERAL
IfaCDdoesnotoperateproperly, presstheresetbutton
with a pointed object such as a pencil, etc. Note that all
your settings will be erased if this button is pressed.
Power-Supply Voltage: 14.4 V (11 to 16 V
allowable), DC, negative ground
Load Impedance: 4 Ω
Tone Control: Bass ± 10 dB at 100 Hz, Treble ±
10 dB at 10 kHz
Preamp Output Voltage (load impedance): 2.2 V
(10 kΩ)
Installed size: 182 (W) × 53 (H) × 155 (D) mm
(7 1/4 (W) × 2 1/8 (H) × 6 1/8 (D) inches)
CARD REMOTE CONTROL
Dimensions: approx. 33 (W) × 85 (H) × 7.5 (D) mm
(1 5/16 (W) × 3 3/8 (H) × 5/16 (D) inches)
Reset button
Weight: approx. 20 g (0.7 oz.) (including battery)
MAINTENANCE
• Specifications and external appearance are subject to
change without notice due to product improvement.
Cleaning the front panel
Wipe the surface with a soft, dry cloth.
REAR PANEL
SPECIFICATIONS
RADIO SECTION
(FM)
Frequency Range: 87.5 MHz – 108 MHz
Usable Sensitivity: 12.7 dBf
50 dB Quieting Sensitivity: 17.2 dBf
IF Rejection: 100 dB
For details, refer to the separate “INSTALLATION AND
CONNECTIONS”.
Frequency Response: 30 Hz – 15,000 Hz
S/N Ratio: 70 dB
Stereo Separation: 35 dB at 1 kHz
Alternate Channel Selectivity: 90 dB
Capture Ratio: 3 dB
The word “BBE” and the “BBE symbol” are trademarks
of BBE Sound,Inc.
Under licence from BBE Sound,Inc.
(AM)
Frequency Range: 530 kHz – 1,710 kHz
Usable Sensitivity: 30 µV (30 dB)
CD SECTION
Frequency Response: 17 Hz – 20 kHz +0/–3 dB
Dynamic Range: More than 92 dB
Channel Separation: More than 60 dB
S/N Ratio: More than 90 dB
Wow/Flutter: Unmeasurable
AUDIO SECTION
Max. Power Output: 45 W × 4 channels
AUX IN input
Input sensitivity (load impedance) AUX IN: 300 mV
(10 kΩ)
ENGLISH 8
Printed in Indonesia
|