DES-1016R+/DES-1024R+
10/100 Fast Ethernet Switch
User’s Guide
First Edition (February 2001)
6DES1016R+01
Printed In Taiwan
RECYCLABLE
Limited Warranty
Hardware:
D-Link warrants each of its hardware products to be free from defects in workmanship and materials
under normal use and service for a period commencing on the date of purchase from D-Link or its
Authorized Reseller and extending for the length of time stipulated by the Authorized Reseller or D-
Link Branch Office nearest to the place of purchase.
This Warranty applies on the condition that the product Registration Card is filled out and returned
to a D-Link office within ninety (90) days of purchase. A list of D-Link offices is provided at the back
of this manual, together with a copy of the Registration Card.
If the product proves defective within the applicable warranty period, D-Link will provide repair or
replacement of the product. D-Link shall have the sole discretion whether to repair or replace, and
replacement product may be new or reconditioned. Replacement product shall be of equivalent or
better specifications, relative to the defective product, but need not be identical. Any product or
part repaired by D-Link pursuant to this warranty shall have a warranty period of not less than 90
days, from date of such repair, irrespective of any earlier expiration of original warranty period.
When D-Link provides replacement, then the defective product becomes the property of D-Link.
Warranty service may be obtained by contacting a D-Link office within the applicable warranty
period, and requesting a Return Material Authorization (RMA) number. If a Registration Card for
the product in question has not been returned to D-Link, then a proof of purchase (such as a copy of
the dated purchase invoice) must be provided. If Purchaser's circumstances require special handling
of warranty correction, then at the time of requesting RMA number, Purchaser may also propose
special procedure as may be suitable to the case.
After an RMA number is issued, the defective product must be packaged securely in the original or
other suitable shipping package to ensure that it will not be damaged in transit, and the RMA
number must be prominently marked on the outside of the package. The package must be mailed or
otherwise shipped to D-Link with all costs of mailing/shipping/insurance prepaid. D-Link shall never
be responsible for any software, firmware, information, or memory data of Purchaser contained in,
stored on, or integrated with any product returned to D-Link pursuant to this warranty.
Any package returned to D-Link without an RMA number will be rejected and shipped back to
Purchaser at Purchaser's expense, and D-Link reserves the right in such a case to levy a reasonable
handling charge in addition mailing or shipping costs.
Software:
Warranty service for software products may be obtained by contacting a D-Link office within the
applicable warranty period. A list of D-Link offices is provided at the back of this manual, together
with a copy of the Registration Card. If a Registration Card for the product in question has not been
returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice)
must be provided when requesting warranty service. The term "purchase" in this software warranty
refers to the purchase transaction and resulting license to use such software.
D-Link warrants that its software products will perform in substantial conformance with the
applicable product documentation provided by D-Link with such software product, for a period of
ninety (90) days from the date of purchase from D-Link or its Authorized Reseller. D-Link warrants
the magnetic media, on which D-Link provides its software product, against failure during the same
warranty period. This warranty applies to purchased software, and to replacement software
provided by D-Link pursuant to this warranty, but shall not apply to any update or replacement
which may be provided for download via the Internet, or to any update which may otherwise be
provided free of charge.
D-Link's sole obligation under this software warranty shall be to replace any defective software
product with product which substantially conforms to D-Link's applicable product documentation.
Purchaser assumes responsibility for the selection of appropriate application and system/platform
software and associated reference materials. D-Link makes no warranty that its software products
will work in combination with any hardware, or any application or system/platform software product
provided by any third party, excepting only such products as are expressly represented, in D-Link's
applicable product documentation as being compatible. D-Link's obligation under this warranty shall
be a reasonable effort to provide compatibility, but D-Link shall have no obligation to provide
compatibility when there is fault in the third-party hardware or software. D-Link makes no
warranty that operation of its software products will be uninterrupted or absolutely error-free, and
no warranty that all defects in the software product, within or without the scope of D-Link's
applicable product documentation, will be corrected.
Warranty Period
For warranty in your region, please check with your local D-Link office and authorized agents as
warranty periods may vary from region to region.
The warranty for power supplies and power adapters is one year.
D-Link Offices for Registration and Warranty Service
The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office.
To obtain an RMA number for warranty service as to a hardware product, or to obtain warranty
service as to a software product, contact the D-Link office nearest you. An address/telephone/fax/e-
mail/Web site list of D-Link offices is provided in the back of this manual.
Limitation of Warranties
IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S
SOLE REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR OR REPLACEMENT. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY
OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE
SALE, INSTALLATION MAINTENANCE OR USE OF D-LINK'S PRODUCTS
D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST
OR WAS CAUSED BY THE CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT,
IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY
OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE,
LIGHTNING OR OTHER HAZARD.
Limitation of Liability
IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA,
LOSS OF PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR
INDIRECT DAMAGES ARISING OUT THE INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE OR INTERRUPTION OF A D- LINK PRODUCT, HOWEVER CAUSED
AND ON ANY THEORY OF LIABILITY. THIS LIMITATION WILL APPLY EVEN IF D-LINK HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO NOT
ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
Trademarks
Copyright ã 2001 D-Link Corporation. Contents subject to change without prior notice. D-Link is a
registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to
their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from D-Link
Corporation/D-Link Systems Inc., as stipulated by the United States Copyright Act of 1976.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this user’ s guide, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CE Mark Warning
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Warnung!
Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen.
In diesem Fall kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.
Precaución!
Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio, en
cuyo case, puede requerirse al usuario para que adopte las medidas adecuadas.
Attention!
Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer des
interférences radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può
causare interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti
adeguati.
VCCI Warning
BSMI Warning
10/100 Fast Ethernet Switch User’ s Guide
1
0 FEATURES
¨
16 or 24 UTP ports all come with NWay auto-negotiation and operate
at 10/100 Mbps for connection to servers and hubs. All ports can
auto-negotiate for full or half-duplex operation.
¨
¨
¨
¨
¨
¨
¨
¨
All ports support auto MDI/MDIX, so there is no need to use cross-
over cables or an up-link port.
Store-and-forward switching scheme capability to support rate
adaptation and ensure data integrity.
Auto-polarity detection for correction of incorrect polarity on the
receive twisted pair at each port.
Data forwarding rate 148,800 pps per port at 100% of wire-speed
for 100Mbps speed.
Data forwarding rate 14,880 pps per port at 100% of wire-speed
for 10Mbps speed.
Data filtering rate eliminates all error packets, runts, etc. at
148,800 pps per port at 100% of wire-speed for 100Mbps speed.
Data filtering rate eliminates all error packets, runts, etc. at
14,880 pps per port at 100% of wire-speed for 10Mbps speed.
Up to 4K unicast address entities per device, self-learning, and
table aging.
¨
¨
256K Byte-on-Chip packet buffer per eight ports.
All 16 or 24 UTP ports support IEEE802.3x flow control for full
duplex and backpressure flow control for half duplex.
¨
Optional two-port Fiber module (SC type connector) in the front
panel for length extension. These two ports operate at either 100M
1
10/100 Fast Ethernet Switch User’ s Guide
full duplex or half duplex by means of a manual setting. Please
see Chapter Two for additional information about module settings.
2
10/100 Fast Ethernet Switch User’ s Guide
2
1 UNPACKING AND SETUP
Unpacking
Open the shipping carton of the Switch and carefully unpack its
contents. The carton should contain the following items:
¨
¨
¨
¨
¨
One DES-1016R+ or DES-1024R+ 10/100 Fast Ethernet Switch
One AC power cord
This User’ s Guide
Four rubber feet with adhesive backing
Screws and two L-type brackets for rack mounting
If any item is found missing or damaged, please contact your local
D-Link reseller for replacement.
Setup
The setup of the Switch can be performed using the following steps:
¨
¨
The surface must support at least 3 kg for the Switch.
The power outlet should be within 1.82 meters (6 feet) of the
device.
¨
¨
Visually inspect the power cord and see that it is fully secured to
the AC power connector.
Make sure that there is proper heat dissipation from and
adequate ventilation around the Switch. Do not place heavy
objects on the Switch.
3
10/100 Fast Ethernet Switch User’ s Guide
Desktop or Shelf Installation
When installing the Switch on a desktop or shelf, the rubber feet
included with the device must be first attached. Attach these cushioning
feet on the bottom at each corner of the device. Allow enough ventilation
space between the device and the objects around it.
Figure 2.1 10/100 Fast Ethernet Switch installed on a Desktop or
Shelf
Rack Installation
The Switch can be mounted in an EIA standard size, 19-inch rack,
which can be placed in a wiring closet with other equipment. To install,
attach the mounting brackets on the switch’ s front panel (one on each
side) and secure them with the screws provided.
4
10/100 Fast Ethernet Switch User’ s Guide
Figure 2.2 Attaching the mounting brackets to the 10/100 Fast
Ethernet Switch
Then, use the screws provided with the equipment rack to mount the
Switch in the rack.
Module Installation
An optional two-port fiber module (SC type connector) can be installed in
the front panel. Follow these steps:
First, set up the module, adjusting the jumper settings as desired. The
default setting is full duplex.
Figure 2.3 Jumper settings on the module
5
10/100 Fast Ethernet Switch User’ s Guide
Next, make sure that the device is powered off and then remove the
plain bracket on the front of the switch.
Figure 2.4 Removing the plain bracket
After removing the plain bracket, slide the module in the guide rails all
the way into the slot and secure the screws.
Figure 2.5 Sliding the module into position
When properly installed, the Slot LED will be lit after powering on the
Switch (see Chapter 3 for more information about LEDs, including a
diagram).
Note: Always remember to turn off the power before a module is inserted
or removed.
6
10/100 Fast Ethernet Switch User’ s Guide
3
2 IDENTIFYING EXTERNAL
COMPONENTS
Front Panel
The front panel of the Switch consists of 16 (DES-1016R+) or 24
(DES-1024R+) 10/100 Mbps MDI-II/MDI-X ports and LED indicators.
Figure 3.1 Front panel view of the DES-1024R+ Switch
Rear Panel
The rear panel of the Switch consists of an AC power connector.
Figure 3.2 Rear panel view of the DES-1024R+ switch
¨
AC Power Connector This is a three-pronged connector that
supports the power cord. Plug in the female connector of the
provided power cord into this connector, and the male into a
power outlet. Supported input voltages range from 100 ~ 240 VAC
at 50 ~ 60 Hz.
7
10/100 Fast Ethernet Switch User’ s Guide
LED Indicators
The LED indicators of the Switch include Power, 100M, Link/Act
(Link/Activity), and Slot. The LED indicators are used to facilitate
monitoring and troubleshooting of the Switch. The following shows the
LED indicators for the Switch along with an explanation of each
indicator.
Figure 3.3 The DES-1024R+ Switch LED indicators
¨
¨
¨
Power This indicator operates when the Switch is turned on. If
this indicator is not lit, check the AC power connector to ensure
proper insertion of the power cord.
100M The LED indicator lights green when a 100 Mbps device is
connected to a respective port. If a 10 Mbps device is connected to
a respective port, the LED indicator is OFF.
Link/Act These LED indicators are lighted green when there is
a secure connection (or link) to a device at any of the ports. The
LED indicators blink green whenever there is reception or
transmission (i.e. Activity—Act) of data occurring at a port.
¨
Slot This LED indicator is lighted green when there is a secure
connection (or link) to an optional two-port 100BASE-FX (SC type)
module is installed in the front panel. Each port has its own LED,
designated as I and II. See 100M and Link/Act indicator
descriptions above for further information.
8
A
3 TECHNICAL SPECIFICATIONS
General
10BASE-T:
Network Cabling:
2-pair UTP Cat. 3, 4, 5 (100m)
EIA/TIA- 568 100-ohm STP (100m)
100BASE-TX:
2-pair UTP Cat. 5 (100m)
EIA/TIA-568 100-ohm STP (100m)
100BASE-FX:
Multi-mode (62.5/125µm or 50/125µm fiber cabling with SC
connector
Number of Ports:
DES-1016R+: 16 x 10/100 Mbps ports
DES-1024R+: 24 x 10/100 Mbps ports
DES-102F: 2 x 100BASE-FX ports
Physical and Environmental
AC inputs:
100 - 240 VAC, 50/60 Hz (internal universal power supply)
Power Consumption: 39 watts maximum
Operating
Temperature:
32 ° ~ 122 °F (0 ° ~ 50 °C)
-13 ° ~ 131 °F (-25 ° ~ 5 5 °C)
5% ~ 95% non-condensing
Storage
Temperature:
Humidity:
EMI:
FCC Class A, CE Mark Class A, VCCI Class A,
BSMI Class A , C-Tick Class A
Safety:
UL (UL 1950), CSA (CSA950), TUV/GS (EN60950)
DC Fan:
One built-in 40 x 40 x 10 mm DC fan
Dimensions:
Weight:
441 x 207 x 44 mm (IU), 19-inch rack-mount width
DES-1016R+: 2.6 kg & DES-1024R+: 2.7 kg
Offices
AUSTRALIA
CANADA
D-LINK AUSTRALASIA
Unit 16, 390 Eastern Valley Way Roseville, NSW 2069 Australia
TEL: 61-2-9417-7100 FAX: 61-2-9417-1077
TOLL FREE (Australia): 1800 177 100 TOLL FREE (New Zealand): 0800-900900
D-LINK CANADA
2180 Winston Park Drive, Oakville, Ontario, L6H 5W1 Canada
TEL: 1-905-829-5033 FAX: 1-905-829-5223 BBS: 1-965-279-8732
DENMARK
EGYPT
D-LINK DENMARK
Naverland 2 DK-2600 Glostrup Copenhagen, Denmark
D-LINK MIDDLE EAST
7 Assem Ben Sabet Street, Heliopolis Cairo, Egypt
E-MAIL: [email protected] & [email protected]
FRANCE
D-LINK FRANCE
Le Florilege #2, Allee de la Fresnerie, 78330 Fontenay le Fleury, France
E-MAIL: [email protected]
GERMANY
D-LINK CENTRAL EUROPE/D-LINK GERMANY
Schwalbacher Strasse 74, 65760 Eschborn, Germany
BBS: 49-(0)6192-971199 (analog)
BBS: 49-(0)6192-971198 (ISDN)
INFO: 00800-7250-0000 (toll free) HELP: 00800-7250-4000 (toll free)
INDIA
D-LINK INDIA
Plot No.5, Kurla-Bandra Complex Rd., Off Cst Rd., Santacruz (E)
Bombay - 400 098 India
E-MAIL: [email protected]
ITALY
D-LINK ITALY
Via Nino Bonnet n.6/b, 20154 Milano, Italy
E-MAIL: [email protected]
JAPAN
D-LINK TOKYO
10F, 8-8-15 Nishi-Gotanda, Shinagawa-ku, Tokyo 141 Japan
E-MAIL: [email protected]
SINGAPORE
D-LINK INTERNATIONAL/D-LINK SINGAPORE
1 International Business Park, #03-12 The Synergy, Singapore 609917
SWEDEN
TAIWAN
D-LINK SWEDEN
P. O. Box 15036, S-167 15 Bromma, Sweden
D-LINK TAIWAN
2F, No. 119 Pao-Chung Rd, Hsin-Tien, Taipei, Taiwan
E-MAIL: [email protected]
U.K.
D-LINK EUROPE/D-LINK U.K.
4th Floor, Merit House, Edgeware Road, Colindale, London NW9 5AB U.K.
E-MAIL: [email protected]
U.S.A.
D-LINK U.S.A.
53 Discovery Drive, Irvine, CA 92618, USA
TEL: 1-949-788-0805 FAX: 1-949-753-7033 BBS: 1-949-455-1779 & 1-949-455-9616
E-MAIL: [email protected] & [email protected]
Registration Card
Print, type or use block letters.
Your name: Mr./Ms
_____________________________________________________________________________
Organization: ________________________________________________
Dept. ____________________________
Your title at organization:
Telephone:
Organization's full address:
________________________________________________________________________
_______________________________________ Fax:________________________________________
______________________________________________________________________
____________________________________________________________________________________________
_____________________________________________________________________________________
Country:
Date of purchase (Month/Day/Year):
_______________________________________________________________
Product Model
Product Serial No.
* Product installed in type of
computer (e.g., Compaq 486)
* Product installed in
computer serial No.
(* Applies to adapters only)
Product was purchased from:
Reseller's name:
______________________________________________________________________________
Telephone:
_______________________________________ Fax:________________________________________
_________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
Reseller's full address:
Answers to the following questions help us to support your product:
1. Where and how will the product primarily be used?
oHome oOffice oTravel oCompany Business oHome Business oPersonal Use
2. How many employees work at installation site?
o1 employee o2-9 o10-49 o50-99 o100-499 o500-999 o1000 or more
3. What network protocol(s) does your organization use ?
oXNS/IPX oTCP/IP oDECnet oOthers_____________________________
4. What network operating system(s) does your organization use ?
oD-Link LANsmart oNovell NetWare oNetWare Lite oSCO Unix/Xenix oPC NFS o3Com 3+Open
oBanyan Vines oDECnet Pathwork oWindows NT oWindows NTAS oWindows '95
oOthers__________________________________________
5. What network management program does your organization use ?
oD-View oHP OpenView/Windows oHP OpenView/Unix oSunNet Manager oNovell NMS
oNetView 6000 oOthers________________________________________
6. What network medium/media does your organization use ?
oFiber-optics oThick coax Ethernet oThin coax Ethernet o10BASE-T UTP/STP
o100BASE-TX o100BASE-T4 o100VGAnyLAN oOthers_________________
7. What applications are used on your network?
oDesktop publishing oSpreadsheet oWord processing oCAD/CAM
oDatabase management oAccounting oOthers_____________________
8. What category best describes your company?
oAerospace oEngineering oEducation oFinance oHospital oLegal oInsurance/Real Estate oManufacturing
oRetail/Chainstore/Wholesale oGovernment oTransportation/Utilities/Communication oVAR
oSystem house/company oOther________________________________
9. Would you recommend your D-Link product to a friend?
oYes oNo oDon't know yet
10.Your comments on this product?
__________________________________________________________________________________________
|