| HFD-135 OM English.qxd 10/14/05 5:35 PM Page 1   IFD™ HIGH PERFORMANCE   AIR PURIFIER   Model HFD-135   9. Do not use air purifier where combustible   gases, vapors or an oxygen rich environment   are present.   IMPORTANT SAFETY   INSTRUCTIONS   10. Do not expose the air purifier to rain, or use   near water, in a bathroom, laundry area or   other damp location.   READ AND SAVE THESE SAFETY   INSTRUCTIONS BEFORE USING   THIS AIR PURIFIER   11. The air purifier must be used in its upright   position.   12. Do not allow foreign objects to enter ventilation   or exhaust opening as this may cause electric   shock or damage to the air purifier. Do not   block air outlets or intakes.   When using electrical appliances, basic   precautions should always be followed to   reduce the risk of fire, electric shock, and   injury to persons, including the following:   13. Locate air purifier near the outlet and avoid   using an extension cord.   1. Read all instructions before operating the air   14. This appliance has a polarized plug (one blade   is wider than the other). To reduce the risk of   shock, this plug is intended to fit only one way   in a polarized outlet. If the plug does not fit   fully in the outlet, reverse the plug. If it still   does not fit, contact a qualified electrician.   DO NOT attempt to defeat this safety feature.   purifier.   2. Place air purifier where it is not easily knocked   over by persons in the household.   3. Always turn the air purifier to the OFF position   and unplug from the wall outlet when not in   use.   15. A loose fit between the AC outlet (receptacle)   and plug may cause overheating and a   distortion of the plug. Contact a qualified   electrician to replace loose or worn outlet.   4. To disconnect the air purifier, first press the   Power ( ) button to turn the air purifier off,   grip the plug and pull it from the wall outlet.   Never pull by the cord.   16. Do not sit, stand or place heavy objects on the   5. Do not use any product with a damaged cord   or plug or if product malfunctions, is dropped   or damaged in any manner. Keep the cord   away from heated surfaces.   air purifier.   17. Disconnect power supply before servicing.   WARNING: To Reduce the risk of fire or electric   shock, do not use this air purifier with any   solid-state speed control device.   6. Do not use air purifier outdoors.   7. Never use air purifier unless it is fully   assembled.   The sealed UV bulbs contain a small amount of   mercury. Dispose of these items at household   hazardous waste collection sites only. If the UV   bulb breaks, do not vacuum or handle with your   bare hands.   8. Do not run power cord under carpets, and do   not cover with throw rugs. Arrange cord such   that it will not be tripped over.   HFD-135 OM English.qxd 10/14/05 5:35 PM Page 3   OPERATION   • Ensure the air purifier is plugged into a working outlet.   • Touch the Power ( ) button to turn the air purifier On.   The LCD screen will display the current setting. (Fig. 2).   Fig. 1   Power Button   Speed +/– Buttons   Filter Reset   Button   UV Reset   Button   • When first starting the unit, you can hear a change in speed   and this is normal.   • To change speeds, press the up (   ) or down (   ) buttons. The display will indicate the current setting:   Low ( ), Medium ( ), High ( ).   Timer Button   • For best results, set the unit to operate at High ( ) speed.   For quieter settings, or during sleep, set the unit to Medium   Timer +/–   Buttons   UV Button   ( ) or Low ( ).   Fig. 2   Indicates continuous operation   • Note that during normal operation, the rotating continuous   operation symbol ( ) will appear in place of timer hours.   • To turn the unit off, touch the Power ( ) button.   Timer Operation   Once the air purifier is turned on, you can program this unit to   turn off automatically after a set amount of time.   • Press the Timer button – the LCD screen flashes the number   18 (Fig. 3).   Fig. 3   • Press the timer plus (   ) or timer minus (   ) buttons to   increase or decrease the desired number of hours (1 to 18).   The selected number will flash for a few seconds – once it   stops flashing, the air purifier is in Timer mode.   (Example: If you want the unit to turn off in 6 hours, touch   the Timer button, then press the timer minus (   until the number "6" is displayed.)   ) button   • The Timer button will be illuminated in Timer mode and the number of hours remaining will be displayed.   • To turn the Timer mode off, press the Timer button. The continuous operation icon ( ) will appear.   DUAL UV LAMP OPERATION   • Press the UV button to turn the Lamps on or off (Fig. 4).   Fig. 4   • The Lamps will light and you will see a faint blue glow   along the top grille of the unit. This is a visual effect. The   UV bulbs are located in the lower portion of the unit.   • The UV button will be illuminated on the control panel.   NOTE: Removing the IFD™ filter assembly or UV cover or   turning the unit off will cancel the UV Lamp function.   3 HFD-135 OM English.qxd 10/14/05 5:35 PM Page 4   REMOVING / CLEANING THE IFD™ FILTER   This IFD™ air purifier is equipped with an electronic filter   Fig. 5   indicator to serve as a convenient guideline for cleaning the   IFD™ and pre-filter based on the air purifier’s hours of use   and operating power level. This is beneficial because a   filter’s life depends on the amount of air and contaminants   drawn through it. As you operate your IFD™ Air Purifier, the   filter bar indicator will fill-up from left to right. The bar will   continue to fill as you use the unit. Once the bar is   completely full, the Filter Reset button will illuminate – it is   time to clean the filters and reset the filter indicator.   Fig. 7   Fig. 6   To reset the filter clean indicator:   • With the power on, press and hold the Filter Reset button   for 10 seconds, or until the filter bar clears itself (Fig. 5).   NOTE: Depending upon your individual usage (environment,   hours and power level of operation), you may need to check   and clean the filters more or less frequently.   To remove the IFD™ filter:   Fig. 8   Fig. 9   • Make certain that the air purifier is OFF and the unit is   unplugged.   • Remove the rear door panel by turning the rear knob   counter-clockwise and lifting the panel out and up.   • Gently tug the filter basket door towards you – the basket   will first rotate and then slide out of the unit (Fig. 6).   Fig. 10   Fig. 11   • Continue to slide the basket and remove from the filter   swing arm (Fig. 7).   • Take the IFD™ filter out of the filter basket and clean the   filter (Fig. 8).   To clean the IFD™ filter:   • After removing the IFD™ Filter from the air purifier, gently   run a vacuum cleaner with a nozzle or brush attachment along the filter to pick-up tiny particles (Fig. 9).   Repeat on both sides.   If your IFD™ filter appears to have dirt that has not been removed by vacuuming, please follow the steps   below to wash the IFD™ filter.   • Turn the power off and unplug the air purifier.   • Remove the IFD™ filter from the unit.   • Fill the sink with lukewarm water and add a few drops of mild dish soap (Fig. 10).   • Gently swish the filter in the soap solution to clean.   • Soak the filter for 2-3 minutes. Do not leave for an extended period of time.   • Rinse the filter with clean tap water.   • Shake the filter to remove any excess water (Fig. 11).   • Place the filter with the honeycomb side down on a plush towel.   • Note that the filter may still be discolored even after washing.   This is acceptable and will not affect performance.   • Allow the IFD™ filter to dry for a few hours or overnight.   • When the IFD™ filter is completely dry, place back into the air purifier.   4 HFD-135 OM English.qxd 10/14/05 5:35 PM Page 5   REMOVING / CLEANING THE IFD™ FILTER (CONTINUED)   CAUTION:   • Never place a wet IFD™ filter in your air purifier.   • The IFD™ Filter is NOT dishwasher safe. Do not place the IFD™ filter in a dishwasher or subject it to   other extreme hot water conditions.   • Do not use any solvents, strong cleaning agents or flammable liquids to clean the IFD™ filter.   Resetting the Filter Clean Indicator   After cleaning the IFD™ filter, you need to reset the filter monitor.   • Once the IFD™ filter has been checked and cleaned, the filter monitor will need to be reset.   • With the air purifier unit powered on, press and hold the filter reset button for approximately 10   seconds or until the LCD display is clear.   CLEANING THE PRE-FILTER   The particle pre-filter helps pick-up large airborne particles that enter the filter. The pre-filter can be   removed and rinsed by hand under warm water. Let the pre-filter dry completely before inserting it back   into the unit.   REPLACING THE ULTRAVIOLET (UV) LAMPS   The UV Reset LED light will illuminate   when it is time to replace the dual UV   bulbs. “Replace UV Bulb” will also   appear in the control panel.   Fig. 13   Fig. 14   Fig. 12   • Be sure to turn off and unplug your   air purifier.   • Remove the UV cover (Fig. 12).   • Turn the UV bulb tab towards the unlock symbol (   (Fig. 13).   ) Fig. 15   • Gently grasp the top of the tab and pull the bulb cartridge   straight out of the UV socket (Fig. 14). Do not touch the   bulb directly with your hands.   • Do the same for the other bulb and pull the bulb cartridge   out of the UV socket.   • Replace the left and right UV bulb sockets with new UV   lamps (part number 135UV).   • Discard old UV bulb cartridge(s) only at household hazardous waste collection sites.   • Place UV cover back in to its place until it clicks in position.   • Plug the air purifier back into an electrical socket and turn the air purifier on.   • Press and hold the UV Reset button for 10 seconds to clear the red LED light and “Replace UV Bulb”   message (Fig. 15).   NOTE: Bulb and bulb housing are not intended for use with any other product or purpose.   NOTE: This unit is equipped with a safety interlock. The unit will not operate while the UV cover is   removed.   5 HFD-135 OM English.qxd 10/14/05 5:35 PM Page 6   INSTALLING THE FILTERS   Fig. 16   Please make certain that the unit is OFF and unplugged.   To install the IFD™ Filter and pre-filter:   IFD™ Filter   • Insert the pre-filter into the basket first.   • Place the IFD™ filter on top of the pre-filter, making certain that the   insert arrows match up with the label outside the basket (Fig. 16).   Pre-filter   Cartridge   • Slide the filter basket onto the swing arm and gently push the filter   basket into the air purifier until it clicks into place.   • Replace the rear panel door by lining up the tabs on the   Fig. 17   Rear   Door   bottom portion of the door with the notches on the air   purifier and then turning the locking knob clockwise   (Fig. 17).   • Turn the locking knob clockwise to lock in place   (Fig. 18).   IFD™ Filter   NOTE: This unit is equipped with a safety interlock. The   unit will not operate while the Rear Door is removed.   Notches   Fig. 18   CLEANING AND MAINTENANCE   • Use a clean, dry cloth to wipe the external surfaces of the air purifier. DO NOT USE WATER, GASOLINE,   POLISH, OR ANY CHEMICAL SOLUTION.   • The IFD™ filter and pre-filter should be cleaned at least once a month, or sooner depending on the air   quality of the room (See “Removing/Cleaning the IFD™ Filter” or “Cleaning the Pre-Filter” respectively).   FREQUENTLY ASKED QUESTIONS   How often is cleaning required?   The IFD™ filter reset light will illuminate to indicate that the IFD™ filter should be cleaned. We   recommend cleaning the filter about once a month depending on the air quality of the room.   I just cleaned my filter but the filter indicator bar is still showing it is dirty, what’s wrong?   Each time you clean your filter you must reset the filter life indicator. It is a timer driven indicator to be   used as a guideline, but does not represent the actual amount of dirt in the IFD™ filter. Press and hold   the appropriate button for up to 10 seconds and when you let go, the filter indicator bar should be   reset.   The filter indicator bar on my unit is completely full but my filter doesn’t really look dirty.   The filter indicator on your unit is timer-based and does not measure the amount of particles in the   IFD™ filter. It is possible that your filter indicator could indicate that the filter is dirty but some particles   are so small that they cannot be seen but are present in the filter. We recommend cleaning the IFD™   filter (see Removing/Cleaning the IFD™ Filter in the manual).   6 HFD-135 OM English.qxd 10/14/05 5:35 PM Page 7   FREQUENTLY ASKED QUESTIONS (CONTINUED)   My filter bar says my filter is still relatively clean but when I checked my filter it was really dirty.   In conditions where smoke, pets or air with a lot of contaminants are present it is possible that the filter   could be dirty sooner than indicated on the indicator. The filter life indicator on your unit runs on a   timer and if there are more particles in your air than in an average home, your filter could capture   airborne particles sooner than indicated on the display. The indicator is intended to be used as a   guideline and individual environmental conditions will vary.   My unit will not turn on.   The air purifier has a safety feature to ensure that all the covers are in place. The rear cover or the UV   cover may not be installed correctly. Check to make sure the rear cover is installed flush with the unit   and is locked. Check that the UV cover is flush with the unit and is snapped into place.   When do the UV bulbs need to be replaced?   The “Replace UV Bulb” message and light will turn on after 6 months of continuous use, so the bulbs   should be replaced at this time.   Is the IFD™ Air Purifier considered an ozone generator?   No. Ozone generators produce large amounts of ozone and the EPA considers these unsafe for   household use.   REPLACEMENT FILTERS / UV BULBS   To order a replacement pre-filter for the IFD™ Air Purifier model HFD-135, visit our website at   www.kaz.com or call us at 1-800-477-0457.   Washable Pre-Filter #60007: $6.25   Replacement UV bulbs (2-pack), model number 135UV: $44.99   IMPORTANT NOTE   The ionizing process used by the air purifier produces small amounts of ozone as a byproduct. The air   purifier complies with U.S. Government limits for acceptable levels of ozone (less than 50 parts per billion   by volume of air circulating through the product). People with a history of respiratory problems or   heart/lung disease should consult a physician prior to using this product.   CONSUMER RELATIONS   Mail questions or comments to:   Kaz, Inc.   Call us toll-free at: 1-800-477-0457   E-mail: [email protected]   Consumer Relations Dept.   250 Turnpike Road   Or visit our website at: www.kaz.com   Southborough, MA 01772   Please be sure to specify a model number.   NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE   YOUR WARRANTY. DO NOT RETURN TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO   OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE   TO THE AIR PURIFIER OR PERSONAL INJURY.   7 HFD-135 OM English.qxd 10/14/05 5:35 PM Page 8   5 YEAR LIMITED WARRANTY   YOU SHOULD FIRST READ ALL INSTRUCTIONS   BEFORE ATTEMPTING TO USE THIS PRODUCT.   C. This warranty does not cover the IFD™ filter or   pre-filter except for material or workmanship   defects.   A. This 5 year limited warranty applies to repair or   replacement of product found to be defective in D. This warranty does not cover damage resulting   material or workmanship. This warranty does   not apply to damage resulting from   commercial, abusive, unreasonable use or   supplemental damage. Defects that are the   result of normal wear and tear will not be   considered manufacturing defects under this   warranty.   KAZ IS NOT LIABLE FOR INCIDENTAL OR   CONSEQUENTIAL DAMAGES OF ANY NATURE.   ANY IMPLIED WARRANTY OF   MERCHANTABILITY OR FITNESS FOR A   PARTICULAR PURPOSE ON THIS PRODUCT IS   LIMITED IN DURATION TO THE DURATION OF   THIS WARRANTY.   Some jurisdictions do not allow the exclusion or   limitation of incidental or consequential   damages or limitations on how long an implied   warranty lasts, so the above limitations or   exclusions may not apply to you. This warranty   gives you specific legal rights, and you also   may have other rights which vary from   jurisdiction to jurisdiction. This warranty applies   only to the original purchaser of this product   from the original date of purchase.   from any unauthorized attempts to repair or   from any use not in accordance with the   instruction manual.   E. Return defective product to Kaz, Inc. with a   brief description of the problem. Include proof   of purchase and a $10 US/$15.50 CAN check   or money order for handling, return packing   and shipping charges. Please include your   name, address and a daytime phone number.   You must prepay shipping charges. Send to:   In U.S.A.:   Kaz, Inc.   Attn: Returns Department   4755 Southpoint Drive   Memphis, TN 38118   USA   In Canada:   Kaz, Inc.   Attn: Returns Department   510 Bronte Street South   Milton, ON L9T 2X6   Canada   B. At its option, Kaz will repair or replace this   product if it is found to be defective in material   or workmanship. Defective product should be   returned to the place of purchase in   accordance with store policy. Thereafter, while   within the warranty period defective product   may be returned to Kaz.   © 2005 Kaz, Incorporated. All Rights Reserved.   P/N: 31IM0135190   |