Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View
VGA Cooler
RAM Heatsink
Nipple
Rubber Ring
VGA RAM
VGA Chipset
PVC Washer
Spring
Fixing Nut
Download from Www.Somanuals.com. All Manuals Search And Download.
※
The specifications of any product may change without prior notice to improve performance.
2
Installation Procedure
※
The following installation sequence MUST be followed.
(1. VGA RAM Heatsink Attachment →2. Thermal Grease Application →3. Nipple Installation on Retention Guide →
4. VGA Cooler Installation → 5. Spring Insertion on the Fixing Nut → 6. Fixing Nut Assembly on VGA Cooler’s
Nipple →7. VGA Card Installation →8. Fan Power Cable Connection)
1. VGA RAM Heatsink Attachment
Remove the film from the Thermal Tapes on the bottom of the
RAM Heatsinks and attach the Heatsinks on the VGA RAM.
RAM
Note 1) If Thermal Grease or other residue remains on the
Heatsink
RAM, then the Thermal Tapes will not stick. Clean the
surface of the RAM with acetone or alcohol before
attaching the RAM Heatsinks.
Note 2) The bonding strength of the Thermal Tapes reaches
VGA
RAM
90% after 24 hours of curing. Do not exert excessive
force on the RAM Heatsinks during this period.
Note 3) Thermal Tapes are not reusable because they lose
adhesiveness after their initial application. Purchase
new Thermal Tapes if the RAM Heatsinks need to be
reattached.
Thermal Tape
2. Thermal Grease Application
Film
Clean the contact surface of the VGA Chipset completely.
Apply Thermal Grease on the VGA Chipset that makes
contact with the base of the VGA Cooler.
Thermal
Grease
3. Nipple Installation on the Retention Guide
Install the short end of the Nipples on the VGA Cooler’s
Retention Guide after determining the appropriate Installation
Holes.
(Note) The Nipples MUST be tightened by hand. Using tools to
tighten the Nipples may damage the tips of the Nipples.
※Please check the table below to identify the correct Nipple
Installation Holes for specific models of VGA cards.
VGA
Chipset
Nipple Installation Holes for
Various VGA Cards
Nipple Installation Holes
VGA Card
Nipple
ATI X1600 Series
ATI X1300 Series
ATI Radeon 9 Series (except 9550/9600)
***
ATI Radeon X Series
***
NVIDIA Geforce4 MX Series
NVIDIA Geforce FX 5200
❶
NVIDIA Geforce FX 5500
NVIDIA Geforce FX 5600 (FX 5700)
NVIDIA Geforce 6600 Series (except 6600 AGP Series)
NVIDIA Geforce4 TI 4 Series
NVIDIA Geforce FX 5700(Ultra) Series
NVIDIA Geforce FX 5800 Series
NVIDIA Geforce 6600 Series (except 6600 AGP Series)
ATI HD 2600 Series
ATI HD 2400 Series
ATI X1650 Series
ATI X1600 Series
NVIDIA Geforce 8600 Series
NVIDIA Geforce 8500 Series
NVIDIA Geforce 7600 Series
NVIDIA Geforce 7300 Series
NVIDIA Geforce 6600 Series (except 6600 AGP Series)
NVIDIA Geforce FX 5900 Series
NVIDIA Geforce FX 5950 Series
NVIDIA Geforce 8800GT, 8800GTS (G92)
ATI HD 3870, HD 3850
Retention
Guide
❷
❸
VGA Cooler
❹
❺
Nipple
Installation
Holes
ATI X1950 Series, ATI X1900 Series
ATI X1800 Series
NVIDIA Geforce 7950 Series
NVIDIA Geforce 7900 Series
NVIDIA Geforce 7600 Series
NVIDIA Geforce 7800 Series
NVIDIA Geforce 6800 Series
NVIDIA Geforce 8800 Series (G80)
Retention Guide
❻
Download from Www.Somanuals.com. All Manuals Search And Download.
※
The specifications of any product may change without prior notice to improve performance.
3
4. VGA Cooler Installation
①Insert the Rubber Rings into the VGA Cooler’s Nipples.
②Install the Nipple-attached VGA Cooler on the VGA card’s Mounting Holes.
※The VGA Chipset MUST be positioned on the center of the VGA Cooler’s base.
③Simultaneously hold the VGA Cooler and the VGA card with one hand, then flip the VGA card so that its rear-
side is facing upwards.
(Note)
Make sure that the VGA Chipset and the VGA Cooler’s base do not get detached while simultaneously flipping
the VGA Cooler and the VGA card.
VGA Cooler
Nipple
Rubber Ring
Nipple
Rubber
Ring
Nipple
VGA
Cooler
Spring
5. Spring Insertion on the Fixing Nut
Slowly turn the Spring in counter clockwise motion so that the
Spring is correctly attached to the Fixing Nut.
Note 1) The ends of the Springs are of different diameters.
Install the Spring end with the smaller diameter on the
Fixing Nut as shown in the diagram.
Fixing Nut
Fixing Nut
Note 2) Make sure that the Spring is installed perpendicularly
and not leaning to one side.
PVC Washer
6. Fixing Nut Installation on the Nipples
①Place a PVC Washer over each Nipple on the back side of
the VGA card.
Nipple
②Slightly screw each of the four Spring-attached Fixing Nuts
onto each Nipple, then tighten each Fixing Nut one rotation
at a time until all are completely tightened.
③Interference may occur between the Fixing Nuts of the two
VGA coolers when using an SLI or CrossFire VGA card
setup. In such a case, use the enclosed Fixing Nut for SLI
/CrossFire for assembly.
For SLI or CrossFire Installations
Fixing Nut for
SLI/CrossFire
PVC Washer
Note 1) Fully tightening one Fixing Nut at a time may result in
damaging the VGA chipset. Please tighten each Fixing
Nut one rotation at a time until all are completely
tightened.
Note 2) Make sure that the VGA Cooler’s base and the VGA
Chipset are completely in contact with each other.
Note 3) Make sure that the VGA Cooler does not interfere with
the VGA card’s capacitors and other components.
Download from Www.Somanuals.com. All Manuals Search And Download.
※
The specifications of any product may change without prior notice to improve performance.
4
7. VGA Card Installation
Insert the assembled VGA card into the motherboard’s PCIe (or AGP) slot. Use the Fixing Bolt to secure the
VGA card onto the computer case. If the VGA card has a power connector on it, then remember to plug in the
power cable.
PCIe Slot
Fixing Bolt
8. Fan Power Cable Connection
①Installing FAN MATE 2 on the Inside of the System ②Installing FAN MATE 2 on the Outside of the System
Double - Sided Tape
RPM Control Knob
Fan Connector
(Z-Machine GV1000)
FAN MATE 2
6-Pin
Connector
Motherboard
Connect the appropriate 3-pin connector on the
cable to the motherboard fan header and the
Z-Machine GV1000 fan connector.
Pull the 6-pin connector out of the system through
the back and connect it to FAN MATE 2, which
should be installed on the case using the included
Double-Sided tape (⑫).
◆ When the RPM Control Knob on FAN MATE 2 is turned fully counter-clockwise, the fan operates in Quite
Mode. Turned fully clockwise, it operates in Performance Mode. You can select the desired fan RPM by
turning the knob.
※Performance can be increased by adjusting the RPM control knob of the FAN MATE 2.
Note) FAN MATE 2 has been specifically designed for the fan of this product.
Zalman Tech Co., Ltd. is not responsible for any damage to systems or VGA Chipsets caused by
using it with other types of fans.
Download from Www.Somanuals.com. All Manuals Search And Download.
※
The specifications of any product may change without prior notice to improve performance.
5
Zalman Computer Noise Prevention Systems
When building a noiseless computer, use Zalman’s Ultra Quiet CPU Cooler, Noiseless Power Supply, Heatpipe
HDD Cooler, Fanless Northbridge Cooler and Noiseless Case Fan for more stable performance and a noiseless
environment.
Noiseless Power Supply
Heatpipe HDD Cooler
Noiseless Case FAN
Ultra Quiet CPU Cooler
Fanless Northbridge Cooler
Computer Enclosures
High End Gaming Enclosure Built with
Sturdy All Aluminum Panels
Three Tool Free Hinged Magnetic Panels
(2 Left, 1 Right) for Easy Installation and
Access to Components
Tool Free Installation of Disk Drives (HDD,
ODD, FDD), Fan Controllers, Audio
Interfaces etc.
Accommodates up to 6 Hard Drives (4 in
the HDD Chassis, 2 on the Bottom Panel)
Luxurious and Cool Aesthetics
Color Options : Black (Red LED Fans),
Titanium (Blue LED Fans)
GT-1000
Home Theatre PC Enclosures
The HD160XT is designed for ultra quiet home theatre
PC operation, utilizing optimized ventilation and
anti-vibration reinforcements, making it ideal for
environments that require silence such as living
rooms, bedrooms, educational facilities, and offices.
For more information, please visit our website.
HD160XT
Download from Www.Somanuals.com. All Manuals Search And Download.
※
The specifications of any product may change without prior notice to improve performance.
6
|