CDR200t
SERIES
User Guide
Guide de I’utilisateur
Bedienungsanleitung
READ
6
WRITE
2
VOL
Recordable
ON/
DISC
READ/
WRITE
Download from Www.Somanuals.com. All Manuals Search And Download.
Laser Diode Properties
Material : GaAlAs
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Wavelength : 780-790 nm
Emission Duration : Continuous
Laser Output Power : Less than 44.6 µW*
*
T
his output is value measured at a
distance 200mm from the objective lens
surface on the optical pick-up block.
ANSI Class : Class 1
This compact disc player is
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label must be
located on the exterior.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
VORSICHT : UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG
GEOFFNET. NICHT DEM STRAHL AUSSETZEN.
VARNING : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN ÄR FARLIG.
Varningsanvisning för
laserstrålning.
VARO! : AVATAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTINA NÄKYMÄTTÖMÄLLE LASERS TEILYLLE. ÄLÄ KATSO SÄTESSEN.
ADVARSEL : USYNLIG LASERSTRALNING VED ÅBNING NÄR SIKKERHETSAF-
BYDERE ER UDE AF FUNKTION. UNDGÅ UDSETTELS FOR STRÅLING.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
❢ WARNING ❢
• The temperature where CDR200t is located
should be between 5ºC and 40ºC (41ºF –
104ºF), when used in a fan-cooled system.
• Do not disassemble the CDR200t cover to
reduce the risk of electric shock.
• Always remove the disc before transporting
CDR200t.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
Important Precautions
Please read the following precautions before
attempting to operate CDR200t.
• Before recording a disc, be sure to clean the disc
and CDR tray using an air aerosol-type dust
remover.
A dust particle on the disc may cause recording
to fail, producing an unuseable disc.
• Always record in a dust-free environment. If the
disc must be removed from CDR200t before
recording is finished, store the disc in a clean,
dust-free environment.
• CDR200t contains no user serviceable parts.
Refer all servicing to qualified personnel.
• If any of the following should occur, CDR200t
should be serviced by qualified personnel:
Metal objects or liquids get inside CDR200t.
CDR200t does not operate normally or a marked
change in performance is noticed.
• Do not place heavy objects on the CD-R discs.
• Do not subject CDR200t and computer to impact
or shock when in use, as this may impair record-
ing or playback.
• Yamaha is not responsible for any data or infor-
mation losses resulting from the operation of
CDR200t.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
Introduction ............................................................................. 1
Chapter 1 - System Configuration ..................................... 3
Troubleshooting ................................................................... 13
Appendix................................................................................. 14
©1996 Yamaha Corporation. All Rights Reserved.
This document may not, in whole or in part, be copied, photocopied, reproduced,
translated, transmitted or reduced to any electronic medium of machine readable
form without prior consent in writing from Yamaha.
Macintosh is a registered trademark of Apple Computer, inc.
Unix is a registered trademark of UNIX System Laboratories.
All other trademarks are the property of their respective companies.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Introduction
Thank you for purchasing a Yamaha CDR200t drive. Please read this
manual before using the drive in order to make the best use of the
superior CDR200t functions. After reading, please retain this manual
for future reference.
CDR200t Features
■ 2xS Recording - 6xS Reading
The CDR200t is a CD-ROM recorder capable of recording at double
speed (2xS), or normal speed (1xS). It can read discs at up to 6xS.
■ Compatible with Seven Different Formats
The CDR200t can both record and read seven different formats: CD-
ROM, CD-ROM XA, CD-I, CD-DA, CD-Bridge (multisession), CD-
Extra, and Video CD. The CDR200t is also equipped with an analog
audio output terminal (headphones) for CD-DA.
■ SCSI 2 for High-Volume, High-Speed Data Transfer
The CDR200t features SCSI 2, the second generation SCSI interface
for connecting computers and peripheral devices. SCSI 2 provides
high-speed transmission of large quantities of data, which is espe-
cially important when working with image data.
■ Compatible with Windows 95 Plug and Play
SCSI IDs are set automatically by the SCAM protocol (level 1).
■ Orange Book Part 2 Compatible 5-Mode Recording
The CDR200t conforms to the five recording modes outlined in the
Orange Book Part 2: Track at Once, Multisession, Disc at Once, Ses-
sion at Once, and Packet Writing.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Orange Book Compatible Recording
Track at Once
In this mode, data can be recorded to disc one track at a time. Discs
recorded in this mode cannot be played in CD players or CD-ROM
drives other than the CD-R drive until the session is closed.
Multisession
In this mode, data can be recorded to disc in stages (one session at a time).
Additional data can be written later.
Disc at Once
In this mode, data can be recorded to an entire disc in one pass.
It is not possible to write additional data later.
Session at Once
In this mode, data can be recorded to disc one session at a time. To use
this mode, your software must support Session at Once recording.
New sessions can be written later.
Packet Writing
This is useful for data back-up. Smaller units of data can be added to
tracks. To use this mode, your software must support Packet Writing.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 - System Configuration
Chapter 1 - System Configuration
In order to use the CDR200t, you will require the following.
For an IBM-PC computer with DOS or Windows
The following operating environment is required:
•
•
An IBM/AT or compatible PC with a 486/33MHz or better CPU
A vacant slot in which to install a SCSI card or a pre-installed
SCSI card
•
•
•
A vacant half-height bay
Windows 3.1 or later, or Windows 95
Sufficient hard disk space
Note: You will need about twice as much space on your hard disk as that
required by the data you wish to write to CD-ROM.
SCSI card and software
This is required in order to connect a SCSI device (the Yamaha
CDR200t) to your computer.
We recommend the following:
Adaptec SCSI cards: AHA-2940 (PCI), AHA-284x (VL), AHA-2740
(EISA), AHA-154x (ISA), etc.
Yamaha CDR200t is a “SCSI” device. You will need to install a SCSI
card and some mastering (writing) software in your host computer to
connect the CDR200t.
For a Macintosh computer
The following operating environment is required:
•
A Macintosh computer that is equipped with a CPU of 68040 or
higher
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 - System Configuration
About Discs
CD-R Discs
On the CDR200t, you can use conventional CD-R discs that conform
to the Recordable Compact Disc Systems Part II (Orange Book).
Yamaha recommends the following Yamaha CD-R discs:
> CDM12Y63 (φ120mm, 63 minutes)
> CDM12Y74 (φ120mm, 74 minutes)
> CDM12Y74M (φ120mm, 74 minutes)
> CDM12Y74T (φ120mm, 74 minutes)
Read-only Discs
You can use discs with the
logo which conform to the Compact
Disc Read Only Memory standard (CD-ROM standard, Yellow
Book). If you wish to use the audio functions, use discs with the
logo, which conform to the Compact Disc Digital Audio standard
(Red Book).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 - Installing the Yamaha CDR200t Drive
Chapter 2 - Installing theYamaha CDR200t Drive
CDR200t drive settings
Before installing the CDR drive into your computer, you will need to
set the following jumpers. You set these jumpers by inserting jumper
connectors into the jumper switch located on the rear panel of the
CDR drive switch.
♦ SCSI ID settings
♦ Parity setting
♦ Terminator setting
♦ Block size setting
Important: Use long-nose pliers to remove or insert jumper connectors.
Rear Panel
ID SELECT
PARITY
SER. NO.
AUDIO OUT
DC INPUT
+5V +12V
TERMINATOR
BLOCK SIZE
1 2 4
R
G
L
G
1
SCSI INTERFACE CONNECTOR
Jumper Switch
ID SELECT
PARITY
TERMINATOR
OUT
BLOCK SIZE
1 2 4
L
SCSI I
PIN 1
PIN 2
PIN 11
PIN 12
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 - Installing the Yamaha CDR200t Drive
♦ SCSI ID settings
The SCSI ID number is used so that the computer will recognize a
connected SCSI device. You can assign 0 through 7 as the SCSI ID
number. Usually, “7” is reserved for the SCSI card ID number, and
“0” is reserved for the first SCSI device in the chain. Use a number
between 1 and 6 for the CDR200t. Refer to the diagram below for
more information on setting the SCSI ID number. The factory set ID
number is “3”.
Important: If you are using other SCSI devices, be sure to use a unique ID num-
ber for each device.
Note: When you are using Windows 95, and if the SCSI ID setting on the
rear panel is the same as the number assigned to another SCSI device,
the Plug and Play component of Windows 95 will automatically
assign an unused number to the CDR200t (SCAM protocol level 1).
1 2 4
1 2 4
1 2 4
1 2 4
SCSI ID 0
1 2 4
SCSI ID 1
1 2 4
SCSI ID 2
1 2 4
SCSI ID 3
1 2 4
SCSI ID 4
SCSI ID 5
SCSI ID 6
SCSI ID 7
SCSI ID Setting
SCSIID
ID 1
ID 2
ID 4
0
1
2
3
4
5
6
7
0 (OPEN)
1 (SHORT)
0 (OPEN)
1 (SHORT)
0 (OPEN)
1 (SHORT)
0 (OPEN)
1 (SHORT)
0 (OPEN)
0 (OPEN)
1 (SHORT)
1 (SHORT)
0 (OPEN)
0 (OPEN)
1 (SHORT)
1 (SHORT)
0 (OPEN)
0 (OPEN)
0 (OPEN)
0 (OPEN)
1 (SHORT)
1 (SHORT)
1 (SHORT)
1 (SHORT)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 - Installing the Yamaha CDR200t Drive
♦ Parity setting
Parity ON (with a jumper)
— Parity Check will be performed. Normally, use this setting.
Parity OFF (without a jumper)
— Parity Check will not be performed.
Parity ON
Parity OFF
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
1 2 4
1 2 4
♦ Terminator setting
The terminator setting indicates whether or not this device is the last
connected SCSI device.
Terminator ON (with a jumper)
— Use this setting if the CDR200t is the last device in the internal
SCSI daisy-chain.
Terminator OFF (without a jumper)
— Use this setting if devices other than the CDR200t are in the inter-
nal SCSI daisy-chain and the CDR200t is not the last device.
Terminator ON
Terminator OFF
ID SELECT
PARITY
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
TERMINATOR
BLOCK SIZE
1 2 4
1 2 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 - Installing the Yamaha CDR200t Drive
♦ Block size setting
Block size ON (with a jumper)
— Block Size is set to 512Byte/sector. This function is valid only for
workstations, such as those that run UNIX.
Block size OFF (without a jumper)
— Normally, use this setting.
Block Size ON
Block Size OFF
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
1 2 4
1 2 4
Cable Connection
SCSI cable
Connect a SCSI cable to the SCSI INTERFACE CONNECTOR on
the rear panel of the CDR200t.
At this time, make sure that figure “1” on upper right corner of
the connector will match the red line on the SCSI cable.
DC INPUT
+5V
G
+12V
1
SER. NO.
ID SELECT
PARITY
TERMINATOR
BLOCK SIZ
SCSI INTE
E
AUDIO OUT
1
2
4
R
G
L
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 - Installing the Yamaha CDR200t Drive
Audio output cable
Connect an audio output cable to the AUDIO OUT connector in the
lower left corner of the rear panel.
Make sure that the projection of the connector is facing upward.
DC INPUT
+5V
G
+12V
1
SER. NO.
ID SELECT
PARITY
TERMINATOR
BLOCK SIZ
SCSI INTERFACE CONNECTOR
E
AUDIO OUT
1
2
4
R
G
L
DC power cable
Connect a DC power cable to the DC INPUT connector on the lower
right corner of the rear panel.
Make sure that the notch on the connector is facing upward.
DC INPUT
+5V
G
+12V
1
SER. NO.
ID SELECT
PARITY
TERMINATOR
BLOCK SIZ
SCSI INTERFACE CONNECTOR
E
AUDIO OUT
1
2
4
R
G
L
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Operation
Chapter 3 - Operation
Front Panel
6
1
READ/
WRITE
ON/
DISC
READ
Recordable
6
WRITE
VOL
2
2
3
4
5
1 Disc tray
The disc is inserted and ejected here. Pressing the eject button will
open the tray.
2 Headphone jack
This stereo mini jack allows you to connect headphones and listen to
audio.
3 Headphone volume control
This control adjusts the volume level of the headphone output. Rotat-
ing the control clockwise will increase the volume level.
4 ON/DISC LED
This indicator lights up in orange when the CDR200t is powered on,
and lights up in green when the CDR200t contains a disc.
5 READ/WRITE LED
This indicator lights up in green when data is being read, and flashes
when data is being accessed. It also lights up in orange when data is
being recorded on a disc.
6 Eject button
This button is used to open or close the tray.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Operation
Loading a Disc
1. Press the eject button to open the tray.
2. Carefully place the disc, label-side up, on the disc tray.
3. Press the disc tray softly or press the eject button again to
close the disc tray.
/
WRITE
Rr
6READ
2WRITE
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Operation
Ejecting the Disc
If the CDR200t is powered on:
Press the eject button to eject the disc.
Note: You cannot eject the disc if the SCSI command prohibits the eject
operation while the CDR200t is reading data.
Caution: Be sure to remove the disc after it is completely ejected. (Trying to
remove the disc before it is completely ejected may cause the drive to
malfunction.)
Press the eject button
READ/
WRITE
ON/
DISC
Recordable
VOL
6READ
2WRITE
If the CDR200t is not powered on:
Pressing the eject button will not eject the disc.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
If CDR200t is not performing as expected, look up the symptoms in the following
table, then see what to do.
Symptoms
What to Do
The power to the CDR200t is off
The power to the computer is off
• Check the DC power cable connection.
• Check to see if the SCSI card is correctly
installed.
The CDR200t is not recognized by • Check the SCSI cable connection.
the computer.
• Make sure that SCSI ID numbers are assigned
exclusively.
• Make sure that the last device in the SCSI daisy
chain is terminated correctly.
The CDR200t does not operate cor- • Install the SCSI driver software again.
rectly
The disc tray will not open
• Make sure that the power to the drive is turned
on.
The disc ejects
• Make sure that the disc is seated in the tray cor-
rectly.
Incorrect operation
• Make sure that the disc is seated in the tray cor-
rectly.
• Make sure that you are using the correct disc.
• Make sure that there is no dust, dirt, or conden-
sation on the disc or tray.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Interface
SCSI 2
Data Capacity
1.2m/sec: 666MB
1.4m/sec: 540MB
Record/Read Speed
Data Transfer Rate
1xS (real-time), 2xS, 4xS (read), 6xS (read)
6xS: 900KB/sec
4xS: 600KB/sec
2xS: 300KB/sec
1xS: 150KB/sec
Burst Transfer Rate
4.2MB/sec (record asynchronous)
3.4MB/sec (read asynchronous)
1MB (250 sectors)
250ms
Buffer Size
Access Speed
Installation
Horizontal<±15 degrees
Disc tray
Disc Loading
Audio Out
Frequency Response
Output Level
20 - 20,000Hz (Line Out)
1 Vrms (Line Out)
(normal speed)
Power Consumption
Power Supply
Environment
11W max (read/write)
5V ±5%, 12V ±10%
Temperature: +5°C - +40°C (read/write, when used in
a fan-cooled system)
Humidity: 25 - 80%
146 x 41.3 x 203 mm
1.3kg
Dimensions (WxHxD)
Weight
Rear Panel
SCSI2/Power Supply
ID Selector
Connector
Non-shielded two-in-one, 50p + 4p
Short-pin 12p
Audio Out
MOLEX 53532-04
Specifications are subject to change without prior notice.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Front Panel Indicator Key
●on: green
✦flashing: green
✧ flashing: orange
— off
❍on: orange
Status
ON/DISC
Read/Write
Reset
—
❍
✧
✦
●
●
●
●
●
●
✧
—
—
—
—
—
✦
Ready (no disc)
Inserting disc
Ejecting disc
Ready (disc inserted)
Seeking
Preparing to write
Writing
✧
❍
✧
Writing (test mode)
Playback
●
—
Error occurred
15
Download from Www.Somanuals.com. All Manuals Search And Download.
YAMAHA CORPORATION
Electronic Systems Division
VY75970-1
Download from Www.Somanuals.com. All Manuals Search And Download.
|