Model No. WLSB62810
WLSG62810
Serial No.
USER’S MANUAL
The serial number is on a plastic sign
inside the spa behind the access
panel. Write the serial number in the
space above.
Access
Panel
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-877-897-7493
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING:
To reduce the risk of drowning, electric shock, or serious injury, read the fol-
lowing important precautions before using the hydrotherapy spa.
READ AND FOLLOW ALL INSTRUCTIONS
1. It is the responsibility of the owner to ensure
that all users of the hydrotherapy spa are
adequately informed of all precautions.
10. Never insert any object into any opening.
11. Do not use breakable containers in or near
the hydrotherapy spa.
2. Use the hydrotherapy spa only as described
in this manual.
12. Do not sit on the spa cover or place objects
on it; it is not designed to support weight.
3. The hydrotherapy spa is intended for home
use only. Do not use the spa in a commercial,
rental, or institutional setting.
13. Remove any water or debris that may collect
on the spa cover.
14. Keep children under the age of 12 and pets
away from the hydrotherapy spa when it is
not in use.
4. Use the hydrotherapy spa only on a level sur-
face. Do not use the spa on carpet or other
materials that could be damaged by moisture.
15. Keep all chemicals away from children and
pets.
5. The hydrotherapy spa will weigh approxi-
mately 2,900 pounds when it is filled with
water. Make sure that the location you select
for the spa will support this weight, plus the
weight of the occupants.
16. The pH and chemical balance of the water
must be maintained as explained in this man-
ual (see pages 10 and 14). Failure to do so
may cause injury to users or damage to the
hydrotherapy spa, and will void the warranty.
6. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
17. Individuals with infections and open sores or
wounds should not use the hydrotherapy
spa. Bacteria thrive in warm and hot water.
Always keep your spa disinfected and main-
tain the proper chemical balance.
7. DANGER—Risk of injury: Do not remove or
alter the covers on the suction fittings. Never
operate the hydrotherapy spa if the suction
guard is missing or broken. If you need to
replace a suction fitting or pump, make sure
you use only manufacturer recommended
replacement parts. Keep hair and body parts
away from the suction guard. Do not allow
long hair to float freely in the water; long hair
should be restrained with a bathing cap.
18. Shower before and after using the hydrother-
apy spa. This will remove any deodorant, per-
spiration, or body oils that could contaminate
the water. Showering after will remove any
residual chemicals and any bacteria that may
have been in the spa.
8. IMPORTANT: Do not allow the hydrotherapy
spa to be exposed to direct sunlight when it
is empty. The surface of the spa shell can
reach temperatures as high as 150°F in a mat-
ter of minutes if exposed to the sun while it is
empty. These high temperatures can cause
significant damage, such as blistering of the
shell surface and warping of the spa shell.
Any damage caused by sun exposure is not
covered under the warranty.
19. WARNING—The Ground Fault Circuit
Interrupter (GFCI), must be tested before
each use. To test the GFCI, press the “test”
button while the hydrotherapy spa is running.
The spa should shut off. Press the “reset”
button. The spa should resume normal opera-
tion. If the spa continues to run after the
“test” button is pressed, then the GFCI is
damaged. Do not use the spa until the GFCI
has been repaired or replaced by a qualified
electrician.
9. Do not bring any object into the hydrotherapy
spa that could damage the spa shell.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. DANGER—Risk of electric shock. Keep all
electrical appliances such as radios, tele-
phones, televisions, and lights at least five
feet away from the water.
physician before using the hydrotherapy spa.
Pregnant women should not use the spa if
the water temperature is above 100°F; the
unborn child could be seriously harmed. This
is especially important during the first 90
days of the pregnancy.
21. A wire connector is provided on the electron-
ics pack of the hydrotherapy spa to connect a
minimum No. 8 AWG (8.04 mm2) solid copper
conductor between the spa and any metal
equipment, electrical enclosure made of
metal, metal water pipes, or conduit within
five feet of the spa.
29. DANGER—To reduce the risk of drowning:
Prolonged immersion in the hydrotherapy spa
may cause hyperthermia. The causes, symp-
toms and effects of hyperthermia may be
described as follows: Hyperthermia occurs
when the internal temperature of the body
reaches a level several degrees above the
normal body temperature of 98.6˚F. The symp-
toms of hyperthermia include an increase in
the internal temperature of the body, dizzi-
ness, lethargy, drowsiness and fainting. The
effects of hyperthermia include failure to per-
ceive heat; failure to recognize the need to
exit the spa or hot tub; unawareness of
impending hazard; fetal damage in pregnant
women; physical inability to exit the spa or
hot tub and unconsciousness resulting in
danger of drowning. WARNING: The use of
alcohol, drugs or medication can greatly
increase the risk of fatal hyperthermia.
22. DANGER—Risk of electric shock: Do not set
the hydrotherapy spa within five feet of any
metal objects or surfaces. As an alternative,
you may use the spa within five feet of metal
objects if each metal object is permanently
connected to the wire connector on the elec-
tronics pack of the spa by a minimum No. 8
AWG (8.04 mm2) solid copper conductor (see
instruction 21).
23. Do not operate the pump motor when the
hydrotherapy spa is empty. The pump motor
may be seriously damaged if it is operated
without water circulating.
24. DANGER—Risk of drowning: Exercise
extreme caution to prevent unauthorized and
unsupervised use of the hydrotherapy spa by
children. Children must always be supervised.
30. WARNING—To reduce the risk of drowning:
Do not use the hydrotherapy spa if you are
under the influence of alcohol or drugs. Heat
from the water, in conjunction with alcohol or
drugs, can cause loss of consciousness.
25. DANGER—To reduce the risk of drowning:
• Never use the hydrotherapy spa alone.
• Children should not use the spa unless they
are supervised by an adult.
31. WARNING—To reduce the risk of injury or
drowning: Consult your physician about pos-
sible side-effects of any medications you may
be taking before using the hydrotherapy spa.
Heat from the water, in conjunction with some
medications, may cause drowsiness and
increase the risk of drowning. Other medica-
tions can effect blood pressure, heart rate,
and circulation.
• Keep pets away from the spa at all times.
• Always replace and lock the spa cover when
the spa is not in use.
26. WARNING—To reduce the risk of injury: The
water temperature should never exceed
104°F. Temperatures between 100°F and 104°F
are considered to be safe for healthy adults.
However, if you plan to remain in the hydro-
therapy spa for more than 10 to 15 minutes, a
lower temperature is recommended. Lower
temperatures are also recommended for chil-
dren. Children should not be allowed to swim
under the surface of the water in the spa.
32. Do not use the hydrotherapy spa immediately
after strenuous exercise.
33. If you feel pain or dizziness at any time while
using the hydrotherapy spa, discontinue use
and contact a physician.
34. WARNING—To reduce the risk of injury: It is
especially important for persons over the age
of 35 or persons with pre-existing health
problems, such as obesity, heart disease,
high or low blood pressure, circulatory prob-
lems, or diabetes to consult their physician
before using the hydrotherapy spa.
27. WARNING—To reduce the risk of injury:
Before entering the hydrotherapy spa, always
use an accurate thermometer to determine
the water temperature.
28. WARNING—To reduce the risk of injury:
Pregnant women should consult with their
4
Download from Www.Somanuals.com. All Manuals Search And Download.
35. WARNING: The spa jets produce a stream of
water with relatively high pressure. Prolonged
exposure of a localized area of the body may
cause bruises to the skin.
36. The included warning sign must be posted
where all users of the hydrotherapy spa can
see and read it. (See POSTING THE WARNING
SIGN on page 2.)
37. WARNING DECAL PLACEMENT: Locate the
decals shown below and familiarize yourself
with the information on the decals.
WARNING:
Read all instructions before using the hydrotherapy spa. ICON assumes no
responsibility for personal injury or property damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the innovative DAYBREAK 628 For your safety and benefit, read this manual care-
hydrotherapy spa by WESLO®. The DAYBREAK 628
hydrotherapy spa offers the features and quality of a
fully before using the DAYBREAK 628. If you have
additional questions, please call our Customer Service
traditional hot tub at an affordable price, giving you the Department toll-free at 1-877-897-7493, Monday
benefits of hydrotherapy in the comfort and privacy of
your own home.
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is WLSB62810 or
WLSG62810. The serial number can be found on a
Hydrotherapy is a proven method for soothing tired
muscles after exercise or for relieving the stress of a
busy life. The warm environment stimulates blood flow, decal attached to the frame inside the spa (see the
which is essential in the healing process, and the pow- front cover of this user’s manual).
erful massage action further eases tension and stress.
The DAYBREAK 628 hydrotherapy spa gives you the
specialized treatment you need to feel your best.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Jets
Air Controls
Spa Shell
Console
Filter
Jet
Access Panel
Locking Buckle
Corner Panel
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Choosing a Location for the Hydrotherapy Spa
There are many factors to consider when choosing a location to set up the hydrotherapy spa. These factors vary
depending on whether you plan to use the spa inside or outside. We have listed several factors you may wish to
consider as you decide where to set up the spa.
If you set up the hydrotherapy spa inside:
If you set up the hydrotherapy spa outside:
1. The spa will increase the level of humidity in your
home. The location you choose should be well
ventilated. You may need to install a ventilation fan
or use a dehumidifier.
1. Check local building codes concerning the use of
outdoor spas.
2. The spa should be located near a 240-volt power
source. It must be wired directly into a grounded
circuit with a Ground Fault Circuit Interrupter
(GFCI) capable of carrying 30 amps. No other
appliance should be on the same circuit.
2. The spa should be located near a 240-volt power
source. It must be wired directly into a grounded
circuit with a Ground Fault Circuit Interrupter
(GFCI) capable of carrying 30 amps. No other
appliance should be on the same circuit.
3. The spa should be close to a source of water.
3. The spa should be close to a source of water.
4. We recommend that you place the spa on a water-
and stain-resistant, non-slip surface. Do not use
the spa on rough or sharp surfaces such as gravel
or wood chips.
4. Do not use the spa on carpet or other material that
may be damaged by moisture. We recommend
that you place the spa on a water- and stain-resis-
tant, non-slip surface with a floor drain for any
water that may splash from the spa.
5. Be sure that the location you choose is stable. It
must be able to support the weight of the spa
when it is filled with water, plus the weight of the
occupants. The spa weighs approximately 2,900
pounds when it is filled with water.
5. Be sure that the location you choose is stable. It
must be able to support the weight of the spa
when it is filled with water, plus the weight of the
occupants. The spa weighs approximately 2,900
pounds when it is filled with water.
6. Consider environmental factors such as rain, wind,
shade, sunlight etc.
6. Do not use the spa above a finished living area,
due to the risk of water damage.
7. You should be able to monitor the use of the spa
from your home, to prevent unauthorized use by
children. You may want to enclose the spa with a
fence and self-latching gate to prevent unautho-
rized use.
7. Be sure that there is room around the spa to per-
mit servicing of the unit. The dimensions of the spa
are 84” W x 84” L x 36” H. You should allow for this
size when choosing the location.
8. Be sure that there is room around the spa to per-
mit servicing of the unit. The dimensions of the spa
are 84” W x 84” L x 36” H. You should allow for this
size when choosing the location.
8. The spa is not designed for in-floor installation.
However, it is compatible with a deck system that
is built flush with the top of the spa, provided you
leave access to the motor for service.
9. The spa is not designed to be installed below
ground level. However, it is compatible with a deck
system that is built flush with the top of the spa,
provided you leave access to the motor for ser-
vice.
9. Be sure to note any other considerations, such as
aesthetics or privacy concerns, that may affect the
safety or enjoyment of using the spa.
10.Be sure to note any other considerations, such as
aesthetics or privacy concerns, that may affect the
safety or enjoyment of using the spa.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Before beginning assembly, carefully read the
following information and instructions:
ASSEMBLY REQUIRES THE FOLLOWING
TOOLS (not included):
• Place all parts in a cleared area and remove the
packing materials from the spa shell. Do not dis-
pose of the packing materials until assembly is
completed and the spa is operating.
• One phillips screwdriver
• You will also need a small amount of soap and
a damp cloth.
• During assembly, make sure that all parts are
oriented as shown in the drawings.
A wire connector is provided on the electronics
pack of the spa to connect a minimum No. 8
AWG (8.04 mm2) solid copper conductor
• Read each assembly step before you begin.
between the spa and any metal equipment,
electrical enclosure made of metal, metal water
pipes, or conduit within five feet of the spa.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1. Before beginning assembly, make sure that you
have read and understand the information in the
box above and on the previous two pages.
1
Spa Shell
Remove the four indicated #10 x 2” Sheet Metal
Screws (6). Remove the Access Panel (15) by sliding
it down and then pulling the bottom away from the
spa. Be careful not to damage the spa shell.
6
15
6
2. Locate the drain hose. Make sure that the cap (not
shown) is fully tightened onto the end of the drain
hose.
2
Gate Valve
Locate the two indicated gate valves inside of the
spa. Make sure that the gate valves are open and
that the locking clips are snapped onto the stems of
the gate valves. In addition,
Collar
Make sure that all of the collars such as the one
indicated are tightened.
See step 1. Re-attach the Access Panel (15) with
the four #10 x 2” Sheet Metal Screws (6).
Drain
Hose
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The hydrotherapy spa operates on a 240-volt power source and must be wired directly to a 30 amp Ground
Fault Circuit Interrupter (GFCI) installed in your home. This procedure must be performed by a qualified,
licensed electrician. A wiring diagram is found on the inside of the electronics package for reference.
Under no circumstances should the spa be wired by someone other than a qualified electrician. Before
you have the spa wired, make sure it is in the desired position, and that it can be easily serviced, if needed.
4. Remove the two warning decals (not shown) from
4
3
the spa shell. Using a damp cloth, wipe the spa shell
clean. Before filling the spa, make sure that it is
in the desired position and that there is room to
service the spa. Once the spa is filled, it will
have to be drained before it can be moved.
5
Fill to Here
Filter
Housing
Insert a garden hose into the filter housing, and
begin filling the spa. Do not use soft water. The
spa may be filled with cold water; however, if warm
or hot water is used, the spa will be ready for use
sooner. Fill the spa until the water is at the level of
the molded fill line. Do not overfill the spa.
Refer to the inset drawing. Set the Filter (5) in the
filter housing. Screw the Filter Cover (3) into the fil-
ter housing until it is fully seated.
Garden Hose
Filter
Housing
5. Pull down one of the straps on the Spa Cover (11)
and hold the Buckle (26) against one of the premium
cedar panels on the spa. (Note: To position the Buckle
correctly, have a second person hold the strap on the
opposite side of the Spa Cover snug.) The Spa
Cover must be snug. Do not place the Buckle over
the grooves between the premium cedar panels.
Refer to the inset drawing. Remove the latch from the
Buckle (26). Attach the Buckle to the premium cedar
panel with two #4 x 3/4” Screws (27).
5
Strap
Latch
11
26
27
Attach the other three Buckles (26) to the premium
cedar panels in the same way.
Strap
Remove the Spa Cover (11) from the spa.
26
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Hydrotherapy Spa
The hydrotherapy spa is designed to seat six adults.
The spa holds 300 gallons of water and offers a heat-
ing system (80°F to 104°F), a filtration system, and
adjustable hydrotherapy jets. Follow the guidelines
below to use and maintain the spa for your long-term
enjoyment.
on the console to the lowest setting (see USING THE
CONTROLS on page 12). The pumping unit will heat
the water as it pumps. Cover the hydrotherapy spa
with the spa cover. The spa cover must be tight
(see SECURING THE SPA COVER ON THE SPA on
this page). The water will heat at about 6°F per hour
with the cover on. If you are using the spa indoors,
and the room temperature is maintained at 70°F, it will
take approximately 6 to 8 hours for the water to reach
the set temperature.
WIRING THE HYDROTHERAPY SPA
The hydrotherapy spa is designed to operate with a
240-volt power source. It must be wired directly into a
grounded circuit with a Ground Fault Circuit
Interrupter (GFCI) capable of carrying 30 amps. No
other appliance should be on the same circuit.
Connection of the spa to the 240-volt power
source must be performed by a qualified, licensed
electrician and must comply with all local, state,
and federal electrical codes. Please refer to the
instructions on the inside of the electronics package
for information about connecting the spa to a 240-volt
power source.
The temperature and the water flow can be set or
changed with the controls on the console (see USING
THE CONTROLS on page 12).
SECURING THE SPA COVER ON THE SPA
To secure the spa cover,
snap the latches on the spa
cover into the buckles on the
premium cedar panels.
Latch
Key
Once the spa is filled with water, the power can be
turned on. Note: The first time the power is turned on,
the spa will start automatically.
To lock the buckles, insert
the key and turn it clock-
wise 1/4 turn. To unlock the
buckles, insert the key and
turn it counterclockwise 1/4
turn. Always keep the
TESTING AND TREATING THE WATER
Buckle
The first time you use the spa, you should test and
treat the water. You must also treat the water each
time you refill the spa. A test strip and a chemical
pack are available at your local pool and spa store.
Follow the directions carefully on the chemical pack to
test and treat the water. Always keep the chemicals
away from children and pets.
buckles locked when the
spa is not in use. Keep the keys in a safe place,
out of the reach of children.
See WATER CHEMISTRY on page 13 for information
concerning proper water maintenance.
STARTING THE HYDROTHERAPY SPA
You should always test the GFCI before using the
hydrotherapy spa. First, turn on the spa by pressing
the pump button on the console (see USING THE
CONTROLS on page 12). Once the spa is running,
press the GFCI “test” button. The spa should shut off.
Press the “reset” button. The spa should resume nor-
mal operation. If the spa continues to run after the
“test” button is pressed, the GFCI is damaged. Do not
use the spa until the GFCI has been repaired or
replaced by a qualified electrician.
Once you have tested the GFCI, you should verify the
water flow from the pumping unit. Set the air control
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Spa Shell Diagram
P
J
P
J
M
L
L
L1
N
N
L1
Seat 2
M
N
N
I
Seat 1
Seat 3
K
B
C
F
D
Seat 4
F
E
Seat 5
H
A
K
G
Seat 6
K
L1
L
K
A. The filter can be removed for cleaning or replace-
costs of the spa’s sanitation.
ment (see CHECKING AND CLEANING THE FILTER
on page 13).
H. The console controls the spa jets, turns the underwa-
ter light on and off, and adjusts the water temperature
setting (see USING THE CONTROLS on page 12).
B. The underwater light can be used for night opera-
tion (see USING THE CONTROLS on page 12). The
spa includes both red and blue covers for the light.
I. The three air controls regulate the air flow to the
hydrotherapy jets.
C. The temperature probe monitors water temperature.
D. The volcano jet provides a soothing foot massage.
J. The four neck jets can be adjusted to spray sooth-
ing water on your neck. To activate the neck jets, turn
the on/off valve (P) counterclockwise. To turn the
neck jets off, turn the on/off valve clockwise.
E. The whirlpool jet diverts the water flow three ways.
By turning the outer ring completely counterclock-
wise, the water flow is diverted to the jets on seats 3,
and the jets labeled D. By turning the outer ring to
the middle position, the water flow is diverted to the
jets on seats 1, 4, 5, and 6. By turning the outer ring
fully clockwise, the water flow is diverted to the
whirlpool jet. Note: The outer ring may be hard to
turn while the pump is turned on high.
K. The nine rotary jets provide a spinning massage.
L. The six dual rotary jets provide a pulsating mas-
sage action. Rotate the outer ring counterclockwise
to turn the jets on. Rotate the outer ring clockwise to
turn the jets off. The jets labeled L1 are always on
regardless of the position of the whirlpool jet (E).
F. The two suction covers provide water to the pump.
Never operate the spa without the suction covers in
place over the fittings.
M. The two power massage jets provides a soothing
massage to your lower back. Turn the outer ring to
regulate the flow.
G. The ozone jet provide ozone sanitation to the spa.
The ozone generator engages during the spa’s filtra-
tion cycles to destroy algae, viruses, and bacteria
while breaking down chemicals and solids for easy
removal by the filtration system. Ozone oxidizes com-
bined chlorine and bromine, freeing them to be con-
tinuously re-used, reducing the chemical needs and
N. The four adjustable, directional jets can be pivoted
to direct their water flow. To open the jets, turn the
rims counterclockwise; to close the jets, turn the outer
rings clockwise. If no air flows through the jets, turn
the jets counterclockwise. Close the jets to increase
the water pressure to other jets.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Controls
Air Controls
Display
Pump
Button Button
Light
Temp
Up
Temp
Down
Refer to the diagram above. The function of each
control is explained below:
To change the water temperature, push either the
temp up or temp down button until the desired tem-
perature is reached.
Pump Button: Turns the spa jets on and off. This is a
two-speed button. If the button is pressed once, the
spa jets will run at low speed, providing gentle
hydrotherapy. If the button is pressed twice, the spa
jets will run at high speed, providing moderate-pres-
sure hydrotherapy. If the button is pressed again, the
jets will shut off.
If the letters OH, FL, or Sn appear in the display, refer
to page 17.
Air Controls: Determine the amount of air flowing
through the spa jets. If a control is turned counter-
clockwise, the amount of air flowing through the jets
will increase; if a control is turned clockwise, the
amount of air will decrease. Test each of the air con-
trols to determine which jets are controlled by which
air control.
The spa also features an automatic mode that heats
and filters the water when the spa is left unattended.
When the power to the spa is first turned on, or if the
water temperature is below the set temperature, the
water will be heated as required to maintain the set
temperature. Note: To keep the filter and heat
cycles from running, the power to the spa must be
turned off.
Light Button: Turns the underwater light on and off.
Temperature Buttons: Control the temperature setting
of the water. The temperature can be set from 80°F to
104°F. The water heats at about 6°F per hour with the
cover on. Use a medical or other accurate thermome-
ter to check the temperature of the water.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
The hydrotherapy spa is designed to provide years of
enjoyment. Please follow the guidelines below to
properly maintain your spa.
entirely. Use a non-silicone-based vinyl conditioner on
the cover after you clean it. This will help protect the
cover from sun damage.
MAINTENANCE SCHEDULE
CHECKING AND CLEANING THE FILTER
Daily
The filter should be checked periodically for build-up
of dirt and oil. If the filter needs to be cleaned, follow
the steps below:
• Check the water level and refill the spa to the level
shown in step 4 on page 9.
• Check the pH balance and sanitizer level. Adjust if
necessary (see WATER CHEMISTRY on page 14).
1. Turn off the power.
2. Unscrew the filter
cover.
Round
Weir
Weekly
• Clean the spa shell at the waterline.
• Check and thoroughly clean the filter (see CHECK-
ING AND CLEANING THE FILTER on this page).
• Replace the filter if needed (see ORDERING
REPLACEMENT PARTS on the back cover).
3. Lift the the filter out
of the filter housing.
4. Check the filter for
dirt and debris. If the
filter needs to be
Filter
cleaned, rinse the fil-
ter with a hose. If the
filter is still dirty, soak
it in cleaning solution
from a pool and spa
supply store.
Monthly
Filter
Housing
• Clean the spa cover (see MAINTAINING THE SPA
COVER on this page).
• Soak the filter for two hours in a trisodium phos-
phate (TSP) solution. Rinse the filter in clean water.
• Replace the filter if needed (see ORDERING
REPLACEMENT PARTS on the back cover).
5. Inspect the filter for
damage. Replace the filter if it is damaged.
6. Insert the cleaned or new filter into the filter hous-
ing.
Every Three Months
• Drain the spa and refill it with clean water. Sanitize
and test the pH of the water.
7. Re-attach the filter cover.
• Check for any leaks around the pump or joints in
the pipes. The seals will wear out over time; detect-
ing leaks early can reduce repair costs.
• Clean the interior of the spa. Do not use solvents or
waxes.
WATER CHEMISTRY
The maintenance of the pH level is very important to
the operation of the spa. To maintain the proper pH
level and to sanitize the spa, you can purchase a
chemical starter kit from your local pool and spa sup-
ply store.
MAINTAINING THE SPA EXTERIOR
The premium cedar surround has been treated at the
factory. For information and supplies to maintain the
beauty and color of the premium cedar surround, con-
tact your local pool and spa supply store.
CAUTION: The chemicals used to maintain the pH
balance of the water and to sanitize the water can
be dangerous. Always follow these basic guide-
lines when handling the chemicals:
1. Always read and follow the directions on the
label, unless directed otherwise.
CLEANING THE SPA SHELL
2. Never mix different chemicals.
The spa shell should be cleaned with a mild soap
solution; do not use solvents. The spa should always
be clean and dry before being moved or stored.
3. Do not exceed the recommended amounts of
chemicals—follow the directions on the label
closely.
4. Keep all chemicals out of the reach of children
and pets.
MAINTAINING THE SPA COVER
5. Keep containers closed tightly when not in use.
6. Never add water to the chemicals—always add
the chemicals to the water as directed.
7. Always store chemicals in a cool, dry place.
The spa cover should be cleaned monthly. To clean
the spa cover, use water and a non-abrasive cleaner
on the entire cover. Rinse the cover with a garden
hose to remove any cleaner residue. Dry the cover
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTAINING THE PROPER PH BALANCE
REMOVING AND ATTACHING THE ACCESS PANEL
The pH factor is a measure of the relative acidity or
alkalinity in the water, and is measured on a scale of
1 to 14. Pure water has a value of 7, which is neutral.
Any value above 7 is alkaline, and any value below 7
is acidic. You should maintain a slightly alkaline pH
level, between 7.2 and 7.8, in the hydrotherapy spa.
To locate the access panels, refer to the drawing on
page 6. Turn off the power to the spa. To remove an
access panel, first remove the four indicated screws.
Slide the access panel down and then pull the bottom
of it away from the spa. Note: Be careful not to
damage the spa shell as you remove the access
panel.
Severe problems can occur when the pH balance is
not maintained within this range. If the pH level
exceeds 7.8, dissolved minerals can build up and clog
the plumbing in the spa jet unit. If the pH level falls
below 7.2, the acid level in the water will begin to cor-
rode the metal parts in the spa jet unit. Also, the sani-
tation agents in the water will not be effective if the pH
level is not properly maintained. Damage caused by
improper pH levels is not covered under the warranty.
Screw
To maintain the proper pH level, test the pH of the
water regularly. To test the water, purchase a pH test
kit at a pool and spa supply store. The pH reading
should be between 7.2 and 7.8. If the level is too low,
add a pH increaser (usually soda ash). If the level is
too high, add a pH reducer (usually sodium bisulfate).
Test the water again after five minutes. See the
instructions with your pH test kit for additional infor-
mation about testing and adjusting the pH.
Access
Panel
Screw
To re-attach the access panel, insert the top of the
access panel under the edge of the spa shell. Slide
the access panel up until the bottom of the access
panel clears the trim along the bottom of the spa.
Then, slide the access panel into place and re-attach
the four screws.
SANITIZING THE HYDROTHERAPY SPA
The most common sanitizing agent is a solid bromine
concentrate. The amount required varies according to
several factors, such as user load, temperature, and
water conditions. Proper water maintenance is a com-
plex process. Contact your local pool and spa supplier
for information concerning which chemicals you
should use in your area to sanitize the spa.
DRAINING THE HYDROTHERAPY SPA
The hydrotherapy spa should be drained at least four
times per year and refilled with clean water. You may
need to drain the spa more often, depending on the
user load. This must be done because after repeated
chemical treatment the water becomes chemically
saturated. Once this happens, additional chemical
treatment of the water is no longer effective. The spa
should also be drained if you will not be using it for
long periods of time. The spa must always be drained
before major repairs are made.
CHANGING THE FILTER CYCLE
The spa will filter the water every 12 hours. The dura-
tion of the cycle can be adjusted to last 2 to 5 hours.
Press the temperature up or temperature down button
on the console. When the display begins to flash,
press the pump button. The display will read F2. To
change the time, press the temp up button until the
desired time is reached. Press the pump button to
confirm the selection. As spa usage increases, the
duration of the filter cycle may need to be increased.
The hydrotherapy spa should always be covered
when it is empty. Direct sunlight can cause exten-
sive damage. The surface of the spa shell can
reach temperatures as high as 150°F in a matter
of minutes if exposed to the sun while it is empty.
These high temperatures can cause significant
damage, such as blistering of the shell surface
and warping of the spa shell. Any damage caused
by sun exposure is not covered under warranty.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To drain the hydrotherapy spa, follow the steps below:
WINTER USE AND CARE
1. Using the console, adjust the temperature to the
lowest setting.
The hydrotherapy spa is designed for year-round use.
If you decide to store the spa for the winter, store it in
2. Shut off the power to the spa, at the circuit breaker a warm, dry location. Follow the steps below to winter-
or GFCI.
ize the spa.
3. Remove the pump access panel from the spa.
4. Pull the hose out and hold it above the waterline.
Remove the cap and attach a garden hose to the
drain hose. Lower the hose and drain the spa.
1. Make sure the power to the spa is turned off.
2. Drain the spa (see DRAINING THE HYDROTHER-
APY SPA on the previous page and this page).
3. Remove all remaining water from the spa shell. Dry
the spa shell with towels.
4. Set the air control to the lowest setting. Use a
wet/dry vacuum to pull any remaining water from
the system. To do this, place the vacuum nozzle
over each jet, starting with the highest jet and fin-
ishing with the lowest jet.
5. Set the air control on the console to the highest
setting and repeat step 3.
6. Drain the pumps (see DRAINING THE PUMPS on
this page). Once the water is drained from the
pumps, place the vacuum nozzle over the drainage
hole in the pumps and vacuum any additional
water from the pumps. Note: For additional pro-
tection, remove the pump/motors from the spa
and store them in a climate-controlled room.
7. Clean the spa shell (see page 13).
Cap
Drain
Hose
8. Clean the filter (see page 13).
5. When the spa is empty, close the valve and
remove the garden hose. Re-attach the cap and
return the drain hose inside the spa.
6. Re-attach the access panel.
9. Shut the power off at the breaker. Label the
breaker in such a way that the breaker will not
be turned on accidentally.
10. Re-attach the access panel and the spa cover.
7. Refill the spa and treat the water with chemicals
(see pages 10 and 14).
REPLACING THE LIGHT BULB
DRAINING THE PUMPS
If the underwater light burns out, you will need to
remove the pump access panel to replace it (see
ATTACHING AND REMOVING THE ACCESS PANEL
on page 14). Make sure the spa power is turned off.
Next, locate the light housing. Turn the light housing
counterclockwise and remove it from the spa shell.
After the hydrotherapy spa is drained, the jet pumps
should also be drained if the spa will be stored for
more than thirty days or if it may be exposed to freez-
ing temperatures.
Turn off the power to
the spa. To drain the jet
pumps, remove the
Light Housing
Light
Bulb
access panel from the
spa unit (see ATTACH-
ING AND REMOVING
THE ACCESS PANEL
on page 14). Locate
the jet pumps inside
the spa. Loosen the
indicated collar on
each of the pumps.
Collar
Light
Housing
To replace the light bulb, pull the old light bulb out of
the housing and insert a new light bulb. Re-attach the
light housing to the spa shell. Re-attach the access
panel to the spa.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-shooting
Most problems can be solved by following the simple steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at
1-877-897-7493, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time.
1. SYMPTOM: THE SPA WILL NOT OPERATE
tained at 70°F, it will take approximately 6 to 8
hours for the water to reach the set temperature.
a. Check to see if the GFCI breaker is tripped or
was not turned on. Reset the GFCI breaker.
b. If you are using the hydrotherapy spa outdoors,
it may take longer for the water to heat. See
the chart below for the approximate heating
time.
2. SYMPTOM: THE CIRCUIT BREAKER OR THE
GFCI TRIPS WHILE THE SPA IS OPERATING
a. Reset the circuit breaker or the GFCI. If the cir-
cuit breaker or the GFCI trips again, contact a
qualified electrician for service.
Air Temperature
70°F +
50°F to 70°F
30°F to 50°F
Heating Time
6 to 8 hours
9 to 11 hours
12 to 14 hours
3. SYMPTOM: THE PUMP HUMS
b. If the water still has not heated after 24 hours,
contact our customer service department.
a. The filter may be dirty or damaged. Remove
the filter from the filter housing and clean or
replace the filter (see page 13).
7. SYMPTOM: THE WATER IS NOT BEING
CLEANED BY THE FILTER
b. The pump may have a foreign object stuck in
the impeller. Contact our customer service
department.
a. Check to see if the filter is in place. Clean the
filter if it is dirty.
c. The pump may have a loose wire connection.
Contact our customer service department.
b. Check the chemical balance of the water. If the
pH is incorrect, the sanitizing agents will not
function properly. See the section on maintain-
ing the proper pH balance on page 14.
4. SYMPTOM: THE PUMP HUMS, BUT DOES NOT
ROTATE
8. SYMPTOM: THE WATER PULSATES OR
THERE IS MINIMUM WATER FLOW
a. The pump may be jammed. Contact our cus-
tomer service department. If your spa is no
longer under warranty, contact a local spa and
pool service provider.
a. This usually occurs only when the water level is
low. Add water until it is 2 to 4” above the skim-
mer basket.
5. SYMPTOM: THE PUMP IS NOISY WHILE
OPERATING
9. SYMPTOM: THE WATER LEVEL DROPS
a. There may be debris in the pump. Contact our
customer service department.
a. A clamp or seal inside the pump compartment
may be loose. Check inside the pump compart-
ment for excess water and watch the pump unit
while it is operating to see if water drips from
any of the plumbing. If you can identify the
location of the leak inside the spa jet unit, tight-
en the clamp or replace the damaged seal.
b. The pump may have a bad bearing. Contact
our customer service department.
6. SYMPTOM: THE WATER DOES NOT HEAT
a. Make sure that the hydrotherapy spa is fully
covered with the spa cover. The spa cover
must be tight for the water to heat. Set the
air control to low. The water will heat at a rate
of 6°F per hour. If you are using the spa
indoors and the room temperature is main-
b. Some water loss due to evaporation is normal.
If rapid water loss occurs, or if you notice wet-
ness on the floor around the hydrotherapy spa,
the spa shell may have a leak. Contact your
local pool and spa service provider for repairs.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
10. SYMPTOM: THE SPA JET UNIT CONTINUES
TO RUN AFTER IT HAS BEEN SHUT OFF
Overheating may occur if the filter cycle is set too
long. At 110° F the spa should reset itself. If the
high-limit sensor detects 118° F at the heater, the
spa will shut down. When the heater cools to 110°
F press any button to reset the spa. If the spa will
not reset, shut off power to the spa and call your
dealer or service organization.
a. To turn the main jets off, press pump button
once or twice. Note: If the actual spa water
temperature is below the set temperature, or if
the spa is running a filter cycle, the heater
pump/motor will not shut off.
FL: Flow. A pressure switch is not working. Call
your dealer or service organization.
11. SYMPTOM: THE LETTERS OH, FL, OR SN
APPEAR IN THE CONSOLE DISPLAY
Sn: Sensor (spa is deactivated). The high-limit
sensor or water temperature sensor is not work-
ing. Call your dealer or service organization.
OH: Overheat (spa is deactivated). Do not enter
the water. If the spa water has reached 112° F,
remove the spa cover to cool the water.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model Nos. WLSB62810, WLSG62810
R1001A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
32
1
1
8
10
1
6
2
1
4
2
2
3
1
8
9
1
1
1
1
4
8
4
1
2
1
1
1
1
Thermometer Fitting
4-wire Power Cord
Filter Cover
filter Cover O-ring
Filter
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
#
1
1
4
1
1
4
10
1
9
4
1
1
1
1
2
1
6
1
1
1
4
1
2
1
1
1
1
1
Diverter
Skimmer Housing*
Medium Jet Housing
Console With Overlay
Large Massage Jet
Nozzle Housing
Jet Ring
Nozzle Bushing
Pivot Ring
Medium Nozzle
Drain Plug
Hose Washer
Pillow
Drain Plug O-ring
On/Off Valve Handle
Hose Cap
Dual Rotary Jet
Ozone Jet Ring
Ozone Jet
Large Rotary Jet
Corner Panel
Ground Wire
Key
#10 x 2” Sheet Metal Screw
Blue Light Cover
Red Light Cover
#10 x 1 1/2” Sheet Metal Screw
#8 x 1 1/2” Screw
Spa Cover
Dual Rotary Jet Housing
Jet Pump/Motor O-ring
Heater/Electronics Package*
Access Panel
#8 x 1/2” Screw
Suction Cover
Air Control Knob
Jet Pump/Motor
Flat Washer
Rotary Jet
Basket
Rubber Isolator
Filter Door
Volcano Jet
Buckle
#4 x 3/4” Screw
Neck Jet
Overlay
Heater Gasket
Whirlpool Jet
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
#
#
#
#
#
#
#
User’s Manual
Large Warning Sign
Warning Sign
Light Bulb
Filter Housing
* Indicates a part that is serviceable only by service
technicians.
# Indicates a non-illustrated part.
Diverter Valve
Trim Plate
Foam
Specifications are subject to change without notice.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model Nos. WLSB62810, WLSG62810
R1001A
11
9
32
19
13
10
35
20
13
36*
48
33
45
23
3
4
1
22
24
9
34
30
14*
20
20
5
29
38
9
30
49
28
20
47
26
49
28
18
27
6
6
54
15
15
6
6
25
2
37
21
8
44
51
43
31
39
53
42
52
40
41
17
17
41
12
16
50
7
46
16
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-877-897-7493, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
1. The MODEL NUMBER of the product (WLSB62810 or WLSG62810)
2. The NAME of the product (DAYBREAK 628 hydrotherapy spa)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and EXPLODED DRAWING
on pages 18 and 19).
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. ICON
extends a limited five (5) year warranty on the spa shell structure. ICON extends a limited two (2) year war-
ranty on the pump, motor, and electronics package. This warranty extends only to the original purchaser.
ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through
one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized
by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage, or repairs not provided by ICON authorized ser-
vice personnel; to products used for commercial or rental purposes; or to products used as store display mod-
els. Specifically excluded are damages caused by or attributable to the following incidents: any damage to the
premium cedar surround or frame attributable to improper handling or freight damage; damage resulting from
improper winterization; damage to the spa shell resulting from improper chemical treatment, damage to the
spa shell resulting from exposure to extreme temperatures, or damage to the spa shell resulting from expo-
sure to direct sunlight and ultraviolet rays while the spa is empty; damage to the pump, motor, plumbing, and
components due to improper maintenance, chemical treatment, or exposure; or damage resulting from failure
to properly follow user’s manual installation, operating, or maintenance instructions. Also excluded are con-
sumable components, including but not restricted to filter cartridges. No other warranty beyond that specifi-
cally set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of or damage
to property including water damage, loss of revenues or profits, loss of enjoyment or use, costs of removal,
installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or
limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 179821 R1001A
Printed in USA © 2001 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|