Viper Home Security System VIPER5706V User Manual

The company behind Viper Auto Security

Systems is Directed.

Since its inception, Directed has had one

purpose, to provide consumers with the fin-

est vehicle security and accessories avail-

able. The recipient of nearly 100 patents and

Innovations Awards in the field of advanced

electronic technology.

Quality Directed products are sold and ser-

viced throughout North America and around

the world.

Call (800) 876-0800 for more information

about our products and services.

NO ONE DARES

COME CLOSE

G5706V 2013-06

Vista, CA 92081

www.viper.com

Directed is committed to delivering

world class quality products and

services that excite and delight our

customers.

5706V

O W N E R’ S G U I D E

Download from Www.Somanuals.com. All Manuals Search And Download.

Congratulations

Congratulations on the purchase of your state-of-the-art security and re-

mote start system. Reading this Owner’s Guide prior to using your sys-

tem will help maximize the use of your system and its many features.

For any additional questions please contact your authorized Directed

dealer or contact Directed at 1-800-753-0600 (US only).

Important information

Government Regulations and Safety information

Read the Government Regulations and Warning! Safety

First sections of this manual prior to operating this system.

Warning! Failure to heed this information can result in

death, personal injury or property damage and may also

result in the illegal use of the system beyond its intended

purpose.

Your Warranty

Your system comes with a warranty. The warranty terms are detailed at

the end of this guide. Make sure that you receive the proof of purchase

from your dealer, indicating the product was installed by an autho-

rized Directed dealer.

Replacement remote controls

Please see your authorized dealer or visit us at www.directedstore.

com to order additional remote controls. Remote control part numbers

are found on the back of the device.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Getting Started.................................................................................................... 4

Charging the remote control:................................................................. 4

Keys to using this manual...................................................................... 5

Responder LC Remote Control .............................................................................. 6

Control Center .................................................................................................... 7

Status Screen Icons.............................................................................................. 8

Using your System............................................................................................. 11

Commands and Confirmations ............................................................ 11

Performing Commands....................................................................... 11

Responder LC Command table ............................................................ 12

Fault Condition Alerts......................................................................... 12

Basic Commands (Direct Access) ........................................................................ 14

Arm ................................................................................................. 14

Disarm ............................................................................................. 14

AUX/Trunk........................................................................................ 15

Remote Start...................................................................................... 15

Advanced Commands: (Level 1) ......................................................................... 16

Silent Arm......................................................................................... 16

AUX 1.............................................................................................. 16

Runtime Reset.................................................................................... 17

Temp Request .................................................................................... 17

Advanced Commands: (Level 2) ......................................................................... 18

Sensor Bypass................................................................................... 18

Remote Valet .................................................................................... 18

AUX 2.............................................................................................. 18

Timer Start ........................................................................................ 19

Runtime Remaining ............................................................................ 19

Advanced Commands: (Level 3) ......................................................................... 20

Sensor Silent Arm .............................................................................. 20

AUX 3.............................................................................................. 20

Smart Start........................................................................................ 21

Alarm Report..................................................................................... 21

Advanced Commands: (Level 4) ......................................................................... 22

Full Silent Arm................................................................................... 22

AUX 4.............................................................................................. 22

Defogger.......................................................................................... 22

Responder LC Configuration............................................................................... 23

Navigating menus and options............................................................ 23

Button operation................................................................................ 23

Access menu items ............................................................................ 23

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu....................................................................................................... 24

Setup Remote menu:........................................................................... 24

Remote Start Info ............................................................................... 25

Runtime Alert..................................................................................... 26

Car 2............................................................................................... 26

Screen Color..................................................................................... 26

Temp Unit ......................................................................................... 26

Button Beep....................................................................................... 27

System Type...................................................................................... 27

Clock Set.......................................................................................... 27

Review ............................................................................................. 27

Exit .................................................................................................. 27

Sensor Adjust:................................................................................... 27

Pair Remote:...................................................................................... 28

Demo mode:..................................................................................... 29

Power Off:........................................................................................ 29

Exit: ................................................................................................. 29

Alarm Features ................................................................................................. 30

Normal Arm Protection....................................................................... 30

Sensor Silent Arm protection ............................................................... 30

Full Silent Arm Protection .................................................................... 31

Sensor Warn-away Messages ............................................................. 31

Full Trigger Messages......................................................................... 31

Emergency Override .......................................................................... 31

Trigger Zone Fault Report.................................................................... 32

Alarm Report when disarming............................................................. 32

Alarm Report when requested ............................................................. 33

Nuisance Prevention (NPC)................................................................. 33

Remote Start Features........................................................................................ 34

Key Takeover..................................................................................... 34

Remote Start Safe-lock........................................................................ 34

Disabling Remote Start ....................................................................... 34

Advanced Start ................................................................................. 34

Temperature Reporting........................................................................ 36

Remote Start Time-out Alert.................................................................. 36

Pit Stop Mode ................................................................................... 36

Manual Transmission Start (MTS mode) ................................................ 37

Turbo Timer Mode.............................................................................. 38

Remote Start Error.............................................................................. 39

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote and System Operations.......................................................................... 40

Passive Arming.................................................................................. 40

Auto Re-arming.................................................................................. 40

Valet Mode....................................................................................... 41

Power Save....................................................................................... 41

Rapid Resume ................................................................................... 41

Automatic Remote Updates ................................................................. 41

Out of Range .................................................................................... 42

No Remote Output............................................................................. 42

Feature not Available ......................................................................... 42

1-way Companion Remote Control..................................................................... 43

Accessing Commands ........................................................................ 43

Button Auto Lock................................................................................ 44

Car Select......................................................................................... 44

Programming .................................................................................... 44

System Expansion Options................................................................................. 47

Battery Information (Responder LC)..................................................................... 49

Low Battery....................................................................................... 49

Battery Life........................................................................................ 50

Battery Information (1-Way) ................................................................ 51

Battery Disposal ................................................................................ 51

Glossary of Terms.............................................................................................. 52

Patent Information............................................................................................. 53

Government Regulations.................................................................................... 54

Warning! Safety First......................................................................................... 56

Installation ........................................................................................ 56

Remote Start Capable ........................................................................ 56

Manual Transmission Vehicles ............................................................. 56

Interference....................................................................................... 58

Upgrades and Batteries...................................................................... 58

Water/Heat Resistance ...................................................................... 58

Limited lifetime consumer warranty..................................................................... 59

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started

Your Responder LC remote is powered by an internal rechargeable

battery that can only be serviced by an authorized Directed dealer.

Due to transit and storage time prior to your purchase, the battery

charge may have depleted. To ensure proper operation, check the

battery level and if not fully charged, use the provided cable to con-

nect to the USB port on a computer. See “Battery Information (Re-

sponder LC)” on page 49 and “Status Screen Icons” on page

8 for more information about the battery.

Charging the remote control:

1. Plug the USB end of the provided USB cable into the USB port

on a computer. Insert the mini-USB connector into the mini-USB

port located on the side of the remote control. The text ﬁeld will

CHARGE

display

to indicate the remote control is charging

(The remote remains operational while charging and can com-

mand the system).

FULL

2. Once fully charged the text ﬁeld will display

3. The remote control is then ready for use. Disconnect the cable

from the remote control end ﬁrst.

If the battery is excessively depleted when charging, func-

tionality may be delayed while it charges to the minimum

voltage required to operate the display, after which normal

charging resumes.

Note

Download from Www.Somanuals.com. All Manuals Search And Download.

Keys to using this manual

Speciﬁc actions (in bold type) and style conventions are used consis-

tently throughout this manual, they are as follows:

•

Press: implies pushing in and releasing a button.

Hold: is used after Press actions when a button needs to be held

in position for an extended period of time, typically several sec-

onds.

ARMED

•

this style denotes the text which appears in the text ﬁeld

portion of the Display during operations described in the manual.

If the text string is too long for the text ﬁeld, it then plays and loops

sequentially word by word.

•

Italicized words denote section/sub headings in this guide and

can be located through the table of contents.

An asterisk (*) when used after a word or phrase denotes that

additional details can be found in related sections usually noted

at the bottom of the page or end of the section.

Download from Www.Somanuals.com. All Manuals Search And Download.

Responder LC Remote Control

Feature

Description

Internal Antenna

Display

Used for transmitting and receiving information

Status screen - the upper portion of the display contains status

icons for the System, Siren, Alarm zones, Remote Start and

Remote Control.

Text field - the lower portion of display - shows the Clock,

Runtime or Temperature during Remote Start, as well as

Command confirmations, Page messages and programming

menus

Command buttons (4)

Used to perform arming, disarming, auxiliary channel and

remote start commands

Used to access function levels for commands, configura-

tion menus for programming, Car Selection, and to request

reports.

Function button

Mini-USB Port

The USB cable plugs into this port (located on remote control

side).

Download from Www.Somanuals.com. All Manuals Search And Download.

Control Center

LED

Control Center

Button

The Control Center, typically located on the upper part of the front

windshield sends and receives commands or messages to and from

your system. It consists of:

•

The In-vehicle system antenna, for 2 way communication.

The Status LED, as a visual indicator of the system’s status.

The Control button, for placing the system into Valet Mode* and

to perform the Emergency Override** operation.

See “Remote and System Operations” on page 40 for details.

** See “Alarm Features” on page 30 for details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Status Screen Icons

ALL

Status Screen

Icons

Text Field

The table below describes all the status screen icons.

Icon

Description

Armed: The system is Armed, the alarm is enabled.

Locked: The system is Locked in Valet, the alarm is disabled.

Disarmed: The system is Disarmed, the alarm is disabled.

Unlocked: The system is Unlocked in Valet, the alarm is dis-

abled.

Siren is disabled for sensor triggers; remote is paged for all trig-

gers (Sensor Silent Arm).

Siren is disabled for all triggers; remote is paged for all triggers

(Full Silent Arm).

+ ALL

Remote start is active, the engine is running.

Timer Start is On; Remote Start is On.

Note: When the icon is without an arrow head: Timer Start is

enabled: Remote Start is Off

Download from Www.Somanuals.com. All Manuals Search And Download.

Icon

Description

Smart Start is On; Remote Start is On.

Note: When the icon is without an arrow head: Smart Start is

On; Remote Start is Off.

Manual Transmission Start mode is enabled, the engine can

be started

Displays the vehicle interior temperature

On during Remote Start after performing the Defogger On

command

On during Warn-away and Full Trigger message output

On during Trunk Zone Full Trigger output and Aux/Trunk

channel activation

On during Fault Report to indicate the Trunk is open and

bypassed when arming

On during a Sensor Zone Full Trigger output

On during Fault Report to indicate a Sensor is active and

bypassed when arming

On during the Door Zone Full Trigger output

On during Fault Report to indicate a Door is open and

bypassed when arming

On during a Hood Zone Full Trigger output

On during Fault Report to indicate the Hood is open and

bypassed when arming

On when remote is set to command the system programmed

as Car 1*

On when remote is set to command the system programmed

as Car 2*

Download from Www.Somanuals.com. All Manuals Search And Download.

Icon

Description

Bars indicate battery level is Full, ¾,½,¼ or Empty

On while the remote control is transmitting a command

On while the remote control is receiving a message

On with Out of Range fault tone to indicate the remote failed to

receive a command confirmation

Pager on: The remote will wake up to listen for messages

Pager off: The remote will not wake up to listen for messages

The remote will Vibrate when messages are received

The remote will emit Beeps and Tones when messages are

received

Text field

Displays the Clock, Runtime, Temperature, message text and

feature menus

On after the Garage Open** message has been received.

On after the Garage Closed** message has been received.

This icon not present until the Car 2 is turned on in the Setup Re-

mote conﬁguration menu.

** This icon not present until the remote is paired with an optional

garage door opener.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using your System

Commands and Conﬁrmations

Commands, Basic or Advanced, are used to activate system features

and are performed by pressing one of the Command buttons. Basic

commands control the most often used security and remote start fea-

tures while Advanced commands control more specialized features

and request reports.

Conﬁrmations for Basic or Advanced commands are indicated

ﬁrst by siren chirps and parking light ﬂashes, and then by Text, Icons

and beeps or tones on the remote control. A description of each

feature conﬁrmation is found in the following Basic command and

Advanced command sections.

Performing Commands

Perform Basic commands by pressing one of the command buttons

while in the Direct Access level. Direct access is available while the

text ﬁeld displays the Clock, Temperature or Runtime. Perform Ad-

vanced commands by ﬁrst accessing one of the Function Levels and

then pressing one of the command buttons while within a level. Func-

tion Levels are available when the text ﬁeld displays LEVEL 1,2,3 or

Advanced command example: Silent Arm

1. Press the

button once to access Function Level 1, the text

LEVEL 1

ﬁeld will display

LEVEL 1

2. Press the

button while

text is still on to perform the

Silent Arm command.

SILENT ARMED

3. The Responder LC remote will display

text ﬁeld and update the status screen icons.

in the

Download from Www.Somanuals.com. All Manuals Search And Download.

Responder LC Command table

Direct Access

Level

Button

x 1

x 2

x 3

x 4

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Arm/Lock

(Panic)

Silent Arm

Sensor

Bypass

Sensor Silent Full Silent

Arm

Disarm/Unlock Silent Disarm Remote Valet Car Finder

Remote Start

Aux/Trunk

Runtime

Reset

Timer Start

AUX 2

Smart Start

AUX 3

Defogger

AUX 4

AUX 1

Advance Level

Change Car

(3s), Enter

programming

(8s)

Temperature

Check

Runtime

Alarm

Report

Remaining

Fault Condition Alerts

If, when performing a command, a condition exists that does not

allow activation of an Alarm feature* or Remote Start feature**,

NOT AVAILABLE

REMOTE START ERROR

the

text and a fault tone will

play.

Alarm feature not available when the system status is incorrect

upon receiving the command. (Example: Sensor bypass com-

mand is received when disarmed).

Refer to the notes included in the following command descriptions

that address these faults or go to “Feature not Available” on page

42 for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

** Remote Start feature not available when the Remote Start status is

incorrect upon receiving the command. (Example: Runtime reset

command received when remote start is off).

Refer to the notes included in the command descriptions that ad-

dress these faults or go to “Remote Start Error” on page 39

for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Commands (Direct Access)

ALL

Arm

Press and release

6:30

The alarm arms, doors lock (if connected), and the siren

chirps and parking lights ﬂash once. The

ARMED

text and beeps play

to conﬁrm and the System Status Icons update. If Valet mode* is On,

VALET

the doors lock and the

arm the alarm normally.

text and tone play. Exit Valet mode to

If a trigger zone fault is detected the siren chirps once again and the

Trigger Zone Fault report** plays.

To Arm and Panic

Press and hold

The alarm Arms (or Locks in Valet) and, after 2 seconds, sounds

PANIC

the siren and ﬂashes the parking lights. The

text and

siren tones play to conﬁrm. Press the

button to stop

the output.

Disarm

Press and release

The alarm disarms, doors unlock (if connected), and the siren chirps

DISARM

and parking lights ﬂash twice. The

text and beeps play to

conﬁrm and the system status icons update. If Valet mode* is On, the

VALET

doors unlock and the

text and tone play.

More than 2 siren chirps and remote beeps indicate a trigger has oc-

DISARM

curred. The

text is replaced by the Alarm report.**

Download from Www.Somanuals.com. All Manuals Search And Download.

AUX/Trunk

Press and hold

AUX

The Trunk opens (if connected) when this button is pressed for 2 sec-

TRUNK

onds. The

text and tones play to conﬁrm.

Remote Start

Press and release

Activates (or if On, deactivates) the remote starter. The engine and

REMOTE START ON

parking lights turn On and the

text and tones play,

REMOTE START OFF

or the engine and parking lights turn Off and the

text and tones play to conﬁrm, the Remote Start status icons update.

The icon will display in the status screen and the text ﬁeld will

display the Runtime, Temperature or Clock as programmed. If Remote

REMOTE START ERROR

Start fails to activate,

text and a fault tone play

while the parking lights ﬂash to identify the reason.***

See “Remote and System Operations” on page 40 for details.

** See “Alarm Features” on page 30 for details.

*** See “Remote Start Error” on page 39 for details.

For Manual transmission vehicles see “Manual Transmission Start (MTS

mode)” on page 37 for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Commands: (Level 1)

ALL

Press and release the

button one time ﬁrst, before

pressing one of the following command buttons.

level 1

Silent Arm

Press and release

The alarm arms, doors lock (if connected), and the parking lights ﬂash

SILENT ARMED

once. The

text plays to conﬁrm and the System Status

icons update. Valet mode* or Trigger Zone Fault report** messages

may be received.

Silent Disarm

Press and release

The alarm disarms, doors unlock (if connected), and the parking lights

SILENT DISARM

ﬂash twice. The

text plays to conﬁrm and the System

Status icons update. The Alarm report** may replace the Silent Dis-

arm text.

AUX 1

Press and release

AUX

AUX CHANNEL

Activates (or if On, deactivates) the Aux 1 output. The

text and On tones or Off tones play to conﬁrm.

Download from Www.Somanuals.com. All Manuals Search And Download.

Runtime Reset

Press and release

If more time is needed while remote start is active, runtime reset

will reset the runtime counter to the pre-programmed setting. The

RUNTIME

text and tones play to conﬁrm. The text ﬁeld will update

if set to display runtime.

Remote Start must be On to use this feature.

Note

Temp Request

Press and hold the

button

Requests the vehicle’s interior temperature and temporarily displays it

via status screen icon and text ﬁeld.

See “Remote and System Operations” on page 40 for details.

** See “Alarm Features” on page 30 for details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Commands: (Level 2)

ALL

Press and release the

button two times ﬁrst, before

pressing one of the following command buttons.

level 2

Sensor Bypass

Press and release

The parking lights ﬂash each time this command is received to in-

dicate the Sensor bypass type. Two ﬂashes indicates sensor Warn-

BYPASS WARN

away zones are bypassed.

, one beep and one fault

tone play to conﬁrm. 3 ﬂashes indicates sensor Warn-away and

BYPASS FULL

Full Trigger zones are bypassed.

, one beep and two

fault tone play to conﬁrm. One ﬂash indicates sensor bypass is Off,

BYPASS OFF

and one beep play to conﬁrm..

System needs to be armed to perform Sensor Bypass.

Perform arm command any time to turn Sensor Bypass Off.

Note

Remote Valet

Press and release

VALET

Enters (or if On, exits) Valet Mode. The

text and beeps (one

for On, two for Off) play to conﬁrm and the System Status icons up-

date. See Valet Mode for more details

AUX 2

Press and release

AUX

AUX CHANNEL

Activates (or if On, deactivates) the Aux 2 output. The

text and On tones or Off tones play to conﬁrm.

Download from Www.Somanuals.com. All Manuals Search And Download.

Timer Start*

Press and release

Activates (or if On, deactivates) Timer Start. The parking lights

ﬂash quickly four times for On and slowly four times for Off. The

TIMER START ON

TIMER START OFF

text and beeps play to con-

ﬁrm and the Remote start status icons update.

System needs to be armed or Timer Start will not start the

engine.

Note

Runtime Remaining

Press and hold the

button

Requests the remaining Remote start runtime and temporarily displays

it in the text ﬁeld.

Remote Start must be On to use this feature.

Note

* See “Advanced Start” on page 34 for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Commands: (Level 3)

ALL

Press and release the

button three times ﬁrst, before

pressing one of the following command buttons.

level 3

Sensor Silent Arm*

Press and release

The alarm arms, doors lock, the siren chirps and parking lights ﬂash

SENSOR SILENT ARM

three times. The

text and beeps play to conﬁrm

and the System and Siren Status icons update.

Car ﬁnder

Press and release

The siren emits one long chirp and the parking lights ﬂash for 10

CAR FINDER

seconds. The

text and beeps play to conﬁrm. The

parking light ﬂashes stop if armed or disarmed while Car Finder is in

progress.

AUX 3

Press and release

AUX

AUX CHANNEL

Activates (or if On, deactivates) the Aux 3 output. The

text and On tones or Off tones play to conﬁrm.

Download from Www.Somanuals.com. All Manuals Search And Download.

Smart Start**

Press and release

Activates (or if On, deactivates) Smart Start. The parking lights

ﬂash quickly ﬁve times for On and slowly ﬁve times for Off. The

SMART START ON

SMART START OFF

text and beeps play to con-

ﬁrm and the Remote start status icons update.

System needs to be armed or Smart Start will not start the

engine.

Note

Alarm Report*

Press and hold the

button

Requests a report of the most recent triggers and temporarily displays it

in the text ﬁeld. The report clears when the ignition is turned on.

See “Alarm Features” on page 30 for more details.

** See “Advanced Start” on page 34 for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Commands: (Level 4)

ALL

Press and release the

button four times ﬁrst, before

pressing one of the following command buttons.

Full Silent Arm*

Press and release

level 4

The alarm arms, doors lock, and the siren chirps and parking lights

FULL SILENT ARM

ﬂash 4 times. The

text and beeps play to conﬁrm

and the System and Siren Status icons update.

AUX 4

Press and release

AUX

AUX CHANNEL

Activates (or if On, deactivates) the Aux 4 output. The

text and On tones or Off tones play to conﬁrm.

Defogger**

Press and release

Activates the vehicle Defogger circuit (if connected) while Remote Start

DEFOG ON

is activated. The

text and beeps play to conﬁrm and the

Remote Start status icons update. For convenience, the Defogger cir-

cuit will also automatically activate 10 seconds after remote starting if

the temperature is below 55°F.

Remote Start must be active to use this feature.

Note

See “Alarm Features” on page 30 for more details.

** This feature must be installed and turned on by an authorized Directed

dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Responder LC Conﬁguration

Operations of the Responder LC and how it communicates messages

are set in the conﬁguration Main Menu.

Navigating menus and options

Navigating menus and features, changing options, and exiting are

performed using the remote control buttons. The following instructions

discuss how to access and conﬁgure the settings.

Button operation

•

To access menus, set options, and to perform actions that are

displayed in the text ﬁeld, use the

To scroll the menu lists in the text ﬁeld use the

To exit conﬁguration: use the or buttons.

button.

AUX

•

buttons.

Access menu items

1. Press and hold the

button for 8 seconds, the remote will beep

is displayed. (If Car 2 is on, ignore the Car

MAIN MENU

once,

Select text and beep after three seconds).

2. Release the button to display the Main Menu item list,

is displayed.

SETUP REMOTE

3. The Main Menu has been accessed and conﬁguring can begin.

Use the following process to view the Main Menu features, op-

tions and settings in the text ﬁeld. The following actions are com-

monly used throughout the conﬁguration operation.

AUX

•

Press the

buttons to change the feature or option

that is displayed in the text ﬁeld.

Press the

button to choose the feature in the text ﬁeld and

view its options. Press it when the desired feature or option

is in the text ﬁeld to set it as the new setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu

The following Main Menu list of features is available for conﬁguration

of the remote control.

Setup Remote menu:

Keypad Lock

OFF AUTO

Options:

OFF

When

, the buttons do not lock and always perform a com-

AUTO

mand when pressed. When set to

, the remote buttons

lock after a 20 second lapse between buttons presses to prevent

unintentional operations. If a button is pressed when locked a

fault tone plays as an alert followed by unlock instructions in the

text ﬁeld.

To unlock the buttons, press the

button. The unlock tones play and

button followed by the

READY

is displayed in the text

ﬁeld, a command can now be performed.

Auto unlocking

After turning the ignition off, a message to the remote will un-

lock the keypad buttons the next command is performed. If Auto

Unlocking is not desired this message can be turned off by an

authorized Directed Dealer.

Page Mode

Options:

POWER SAVE OFF

Paging is how the Responder LC remote monitors your system’s

POWER SAVE

messages.

extends battery life by turning Paging

Download from Www.Somanuals.com. All Manuals Search And Download.

Off after one week if the remote control is not used during this

period. Just press any button to resume system monitoring. When

set to

it wakes up every few seconds to listen for pages

OFF

from the system. When set to

it does not wake up to receive

remote start or alarm trigger pages.

OFF

Note: When

, responses are still received when a command

is performed but alarm trigger pages will not be received.

Page Alert

Options:

TONE VIBE TONE

VIBE

SCREEN ONLY

There are several ways for the Responder LC to alert you when it

has received a message from the system.

TONE VIBE

will alert by both emitting tones and vibrating the re-

TONE

mote. Select

to be alerted by tones that are unique for

VIBE

each message. Select

and the Responder LC will silently

SCREEN ONLY

alert you with a gentle vibration, or select

don’t want to be interrupted.

when you

Remote Start Info

RUNTIME

TEMP CLOCK

Options:

The text ﬁeld can be set to display the information you prefer dur-

RUNTIME

TEMP

ing remote start.

: Remote Start Runtime,

: vehicle

CLOCK

interior Temperature, or the

ﬁeld while Remote Start is on.

will be displayed in the text

Download from Www.Somanuals.com. All Manuals Search And Download.

Runtime Alert

OFF

Options:

The main unit will send a page to alert you when the runtime is

about to expire. When set to

, an alert is generated when

OFF

the Remote Start Time-out message is received. When

alert output is emitted for the message.

, no

Car 2

Options:

OFF

ON HOME

This remote can control two systems independently. When set to

OFF

, the Car2 select option is not available. When set to

HOME

the remote can be set to control two systems. The

is for pairing to a home security system.

option

Screen Color

OFF WHITE LT GRN VIOLET AQUA

RED

GREEN BLUE

Options:

OFF

The status screen backlighting can be

, or will illuminate

with a selected color during output when set to one of the option

colors.

Temp Unit

Options:

Temperature can be displayed in your choice of temperature

scales, Fahrenheit or Celsius.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Beep

OFF

Options:

When set to

, the remote will emit a beep as conﬁrmation

OFF

of a button press. When set to

button presses.

, beeps are not emitted for

System Type

SEC RKE

Options:

Selects the type of system, namely; Security or Remote Keyless

Entry to which the remote has been paired, and adjusts the text

and main menu accordingly. This has been pre-set by the factory

for your system.

Clock Set

Options:

HOUR MIN

Review

Displays ﬁrmware version

Exit

Exits and returns to the main menu

Sensor Adjust:

If you feel your security system shock sensor is too sensitive or not

sensitive enough, it is highly recommended that you contact your au-

thorized Directed dealer/professional and have the sensor adjusted

for optimized security detection performance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Pair Remote:

Remote Pair is a process where the Responder LC and the system in

the vehicle learn each others encrypted identiﬁcation, securing their

communication from intruders. Please note that your remote controls

come pre-programmed from the factory.

Prepare the vehicle system to be Paired with a new remote

1. Open at least one of the vehicle’s doors.

2. Turn the key to the On position.

3. Within ﬁve seconds press and release one time the Control but-

ton on the Control Center.

4. Within ﬁve seconds, press and hold the Control button. The sta-

tus LED will ﬂash one time and the siren will chirp once to conﬁrm

the system is ready for remote pairing.

5. Release the Control button and proceed below.

Note: If pairing does not result within 60 seconds, the system will exit

and the siren will chirp.

Prepare the new remote to be Paired with the system

1. Make sure the remote control is set for the desired Car 1 or Car

2 operation.

2. Perform the steps under Access menu items section to access the

Pair Remote mode.

PAIR

3. When the remote beeps three times and

remote is ready to pair.

is displayed the

4. Press the

button.

5. Wait several seconds for feedback as the remote generates a

security encryption and sends it to the Control Center. If Pair is

successful the siren sounds and the remote emits several tones.

The screen displays if the Pairing is successful or failed with cor-

responding text. If pairing failed, repeat step 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

Demo mode:

Demo Mode plays a pre-selected group of animations as a demon-

stration tool to show friends or family. Running Demo mode shortens

the battery life over time if used excessively

SINGLE SILENT

•

: The remote will display a selection of icons on

the status screen without beeps and tones then stop

: The remote will display a selection of icons on

the status screen with beeps and tones then stop

SINGLE SOUND

Power Off:

When an extended period of non-operation is anticipated, turning the

power off will preserve the battery charge. Press the

button while

POWER OFF

is displayed. The status screen icons clear as the power

off tones play, the remote is turned off.

To turn the remote on, Press and hold the

button for three seconds,

the status screen icons refresh as the power on tones play. The remote

also turns itself on and begins charging when the battery charger is

connected.

Exit:

To return to normal operation, press the

played.

button while EXIT is dis-

Download from Www.Somanuals.com. All Manuals Search And Download.

Alarm Features

Normal Arm Protection

Status LED: The Control Center Status LED ﬂashes as a visual indicator

that your vehicle’s security system is active.

Starter Kill: The Failsafe starter kill relay prevents the engine from

starting

May require additional parts and installation

Note

Sensor triggers: The shock sensor can distinguish minor impacts from

major impacts to the vehicle exterior. Minor impacts causes the system

to emit a Warn-away output by chirping the siren and ﬂashing the

parking lights for three seconds. Major impacts caused for example

by a forcible entry attempt, results in a Full Trigger output. The siren

sounds and the parking lights ﬂash for 30 seconds or longer. Both

Warn-away and Full Triggers send a message to the remote control.

Point of entry triggers: Opening the hood or trunk causes a Full Trig-

ger output, while opening a Door or turning on the Ignition causes

the the siren to chirp three seconds before beginning the Full Trigger

output. This three second delay allows time to disarm and silence the

siren in case of accidental trigger. The Full Trigger message is still sent

to the remote.

Sensor Silent Arm protection

Sensor Warn-away and Sensor Full Trigger activations only send mes-

sages to the remote, while the parking light ﬂash and siren outputs are

defeated. Point of entry triggers will activate the parking light ﬂash,

siren, and send messages normally.

Download from Www.Somanuals.com. All Manuals Search And Download.

Full Silent Arm Protection

Sensor Warn-away, Sensor Full Trigger and Point of Entry activations

will only send messages to the remote, with parking light ﬂash and

siren outputs defeated.

Sensor Warn-away Messages

When the remote receives a Sensor Warn-away message it emits

SENSOR WARN

10 beeps (if on) and displays a sensor zone speciﬁc

text for 30 seconds. Warn-away messages cannot be reviewed or

displayed in reports.

Full Trigger Messages

A Full Trigger message generates a Full Trigger output of siren tones

TRIGGER

and zone speciﬁc

text followed by an alert that consists of

one long beep per minute for 10 minutes.

To stop the output and alert, press a command button to perform a

command, or Press the

button.

Emergency Override

The following procedure disarms the system when a programmed re-

mote is not available. Number of presses__________

1. Turn the ignition On.

2. Press the control button on the Control Center the correct

number of times (the default is one press).

3. After a few seconds the siren output ceases and the system

is disarmed.

As a precaution, if programmed for Passive Arming or Auto

re-arming the system should be placed into Valet Mode until

a remote is available .

Note

Download from Www.Somanuals.com. All Manuals Search And Download.

Trigger Zone Fault Report

When armed by remote command the system runs a status check

of the alarm trigger zones. Faulty zones (usually caused by dome

light delay or open trunk) are bypassed and reported via the control

center LED and remote, while all other trigger zones remain active

and are monitored to protect the vehicle. Should a faulty zone self

correct (dome light turns off) it becomes active and is then monitored

normally.

The siren chirps once again a few seconds following the arming

chirps as an audible alert, the control center LED ﬂashes in groups to

indicate the zone number. The remote will emit a single fault tone and

play zone speciﬁc text that identiﬁes the faulty zones.

Alarm Report when disarming

The most recent alarm triggers (if any) are reported when the alarm

is disarmed via the remote control, siren chirps, parking light and

control center LED ﬂashes. The siren chirps four times (or ﬁve times

if NPC On*), the parking lights ﬂash three times, and the control

center LED ﬂashes in groups to indicate the last two zones that were

DISARM

triggered (see Table of Zones). The

text is replaced by

ALARM REPORT

and text identifying the triggers.

* See “Nuisance Prevention (NPC)” on page 33 for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Zones

Zone Name

Zone # (led flashes)

Trunk

Shock Sensor

Door

Sensor 2

Ignition

Hood

Alarm Report when requested

The Alarm Report displays the two most recent alarm triggers depend-

ing on the system state when requested. When disarmed, the report

will display text to identify the two most recent triggers since the ve-

hicle was last driven. When armed, the report will display text to

identify the two most recent triggers since the system was armed.

The Alarm Report clears when ignition is turned on.

Note

Nuisance Prevention (NPC)

NPC monitors all alarm zones and, if any are triggered excessively,

bypasses them until corrected. If a point of entry (trunk, hood, door)

is left open following a forced entry, it is bypassed. It becomes active

again only after being closed.

Bypassed sensors automatically reset after one hour and after the

vehicle is driven. Disarming then re-arming the alarm does not reset

bypassed sensors.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Start Features

Key Takeover

When you are ready to drive

The system keeps the engine running until the vehicle is ready to be

driven. To perform Key Takeover:

1. Disarm the system and enter the vehicle, do not step on the foot

brake.

2. Insert the key, turn it to the run position, and then step on the foot

brake, the remote start then turns off.

3. The parking lights turn off to indicate remote start is off, and

REMOTE START OFF

then after a few seconds the remote plays the

message.

4. The vehicle is ready to drive.

Remote Start Safe-lock

Remote start safe-lock makes sure the doors are locked while the en-

gine is running and after, even if they are unlocked when remote start

is activated. Door locks may require additional parts and labor.

Disabling Remote Start

Remote start can be disabled by moving the Toggle Switch to the Off

position. If remote start is attempted while Off, the engine will not start.

(See “Remote Start Error” on page 39) move the switch back to the

On position to resume normal operation.

Advanced Start

The Advanced start features Timer Start and Smart Start will automati-

Download from Www.Somanuals.com. All Manuals Search And Download.

cally start the engine to maintain battery charge or combat extreme

cold when parked for an extended period of time.

Precautions for the Advanced Start features:

•

Park the vehicle in a well ventilated area away from windows

and doors that lead into inhabited spaces.

Arm and Lock the vehicle, the engine will not start unless the

doors are locked.

Only one Advanced start feature can be enabled at any given

time.

For manual transmission vehicles MTS mode must be enabled

before Timer Start or Smart Start can be activated.

Timer Start or Smart Start mode automatically exits when the ve-

hicle is disarmed.

Timer Start operation

Activation begins a countdown timer as set by the installer (de-

fault 3 hours). When the timer expires the engine starts and the

REMOTE START ON

message is sent to the remote control. When the

REMOTE START OFF

Remote start runtime expires the engine shuts off, the

message is sent to the remote control and the countdown timer restarts.

This will repeat as many times as set by the installer (default 6 starts).

Timer Start is exited after the ﬁnal start.

Smart Start operation

Smart Start uses the settings for Timer Start in addition to temperature

and battery level to automatically start the engine. Activation begins

the countdown timer. When the timer expires the vehicle interior tem-

perature and battery level is checked and, if the Temperature is above

100°F, below 0°F, or the battery level is below 10.5V, the engine

REMOTE START ON

will start and the

message will be sent to the remote

Download from Www.Somanuals.com. All Manuals Search And Download.

controls. When the Remote start runtime expires the engine shuts off,

REMOTE START OFF

the

message is sent to the remote control and the

countdown timer restarts. Smart Start is exited after the ﬁnal start.

The temperature and battery thresholds can be changed by

an authorized Directed dealer if a higher or lower threshold

is desired.

Note

Temperature Reporting

During Remote start the vehicle interior is checked regularly for tem-

perature changes. If a change in temperature is detected this report

will be sent to the remote for display. Each time the remote receives

this report it will beep, update, and display the newest temperature

information using the Temperature Gauge icon.

Temperature report must be turned on by an authorized Di-

rected dealer.

Note

Remote Start Time-out Alert

During remote start a message is sent three minutes before and again

RUNTIME LOW

at one minute before the engine turns off. The

text plays

with tones as an alert to reset the runtime if desired.

Pit Stop Mode

To exit vehicle with engine running

The system keeps the engine running during short trips into the house

or convenience store. To perform Pit Stop:

1. With the engine running, set the parking brake and release the

foot brake.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Press the

button, the parking lights will turn on and the

REMOTE START ON

message will play on the remote control.

3. Turn the key to off, and remove it from the ignition, the engine

continues running for the programmed runtime.

4. Exit the vehicle and arm the alarm.

For Pit Stop on manual transmission vehicles follow the di-

rections in the Manual Transmission Start (MTS mode) sec-

tion with the door open.

Note

Manual Transmission Start (MTS mode)

When installed into a manual transmission vehicle, the system requires

that the MTS mode is properly set when parking. If MTS mode is not

properly set or is defeated after being properly set the system will not

REMOTE START ERROR

start the engine and the

an alert.

text and tones play as

1. With the engine running, press the foot brake then set the parking

brake and leave the engine running. For Pit Stop or Turbo Timer

mode (to leave the engine running after arming) open the driver

door.

2. Release the foot brake. As long as the engine is running there is

no time limit to perform this step.

3. Within 20 seconds of foot brake release, press any command

button on the remote, after 20 seconds return to Step 2 (For Turbo

Timer Mode, press the optional dash mounted activation button

or send the Timer Mode command from the Advanced Start menu

screen).

4. The parking lights ﬂash ﬁve times to conﬁrm MTS mode en-

able and the remote start activates the ignition outputs. The

REMOTE START ON

text and beeps play to conﬁrm.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Turn Off and remove the key from the ignition switch, the engine

remains running.

6. Exit the vehicle, close all the doors and arm the system.

REMOTE START OFF

7. The engine turns off and after a few seconds, the

message plays to conﬁrm. If the door is opened in Step 3 then

the engine continues to run.

Turbo Timer Mode

The system keeps the engine running for the Turbo Timer runtime and

can be activated by remote control or optional dash mounted activa-

tion button.

1. With the engine running, set the parking brake.

2. Press the optional dash mounted activation button or perform the

Timer Mode command (for manual transmission vehicle see previ-

ous MTS mode section).

3. The parking lights turn on and the remote start activates the igni-

REMOTE START ON

tion outputs. The

ﬁrm.

text and beeps play to con-

4. Turn Off and remove the key from the ignition switch, the engine

remains running.

5. Exit the vehicle, close all the doors and arm the system.

6. The engine runs for the Turbo Mode runtime.

Turbo Timer must be turned on by an authorized Directed

dealer.

Note

For Turbo Timer mode on manual transmission vehicles fol-

low the directions in the Manual Transmission Start (MTS

mode) section with the door open and in step 3 send the

Timer Mode command from the remote control.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Start Error

For user safety, the system must be properly conﬁgured or remote start

will not activate. If the remote start fails to active, refer to the follow-

ing table for the screens and parking light ﬂashes that will identify the

conﬁguration issue and resolution.

Flashes *

Possible Fault

Solution

Brake on

Release foot brake

Hood open

Close hood

After performing Remote Start

command - MTS not enabled

Enable MTS mode

After performing Timer Start or

Smart Start command

Check all Solutions

Toggle Switch off

Alarm is triggered

Turn switch on

None

Disarm or reset alarm

* Refers to the number of parking light ﬂashes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote and System Operations

Passive Arming*

Park and exit the vehicle, after the doors are closed the Passive arm-

ing countdown begins. The led ﬂashes quickly and upon reaching 20

seconds the siren then chirps once. At 30 seconds the system arms

itself.

Anytime before the system arms you can re-enter the vehicle or

open the trunk to load or unload items and, after closing passive arm-

ing resumes.

To stay secure in case of accidental disarming the system, if a

door is not opened within 30 seconds the system re-arms itself and

locks the doors.

Auto Re-arming*

Auto re-arm ensures the vehicle stays protected if it is not entered after

disarming by remote control. After disarming by remote, the alarm

automatically re-arms itself (and locks the doors if programmed on) in

30 seconds. Open any point of entry to stop the re-arm until the next

disarm by remote.

Onetime Bypass*

Turn the ignition On for one to three seconds and then Off. The siren

chirps once to conﬁrm one-time bypass is enabled.

One-time bypass can be used to temporarily bypass the Passive arm-

ing operation for one cycle. It also bypasses the comfort closure and

auxiliary channel outputs programmed to activate when arming. After

the next disarm all operations return to normal.

* These features must be turned on by an authorized Directed dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Valet Mode

Valet mode can be entered and exited by performing the Remote Valet

command or manually using the vehicle key and the control button.

When entered, the alarm functions are defeated while the conve-

nience features still operate normally.

Arm and Disarm commands lock and unlock the doors while the

VALET

text and beeps play to conﬁrm.

Use the following steps to manually enter and exit Valet Mode:

1. Turn the ignition switch On and then Off

2. Immediately press and release the control button once

3. The control center LED turns On when entering and Off when

exiting.

Power Save

To reduce power consumption the control center status LED modiﬁes

its output if the vehicle is parked for an extended period. If Armed the

ﬂashing is reduced after 24 hours. When Valet mode is On the LED

will turn off one hour and will reset each time the ignition is turned off.

Rapid Resume

If power is ever disconnected by a mechanic or thief, the system will

resume the state it was in at the time of disconnection, when power

is reconnected.

Automatic Remote Updates

The system sends a silent message to all remote controls after any

major action has occurred. When the remote receives this message it

updates the status screen icons. This way all users are able to quickly

review the system status just by accessing the status screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Out of Range

Each time a command is performed the remote will expect a com-

mand conﬁrmation from the system. If a command conﬁrmation is not

received the out-of-range icon ( ) and a fault tone will play as an

alert.

No Remote Output

Occasionally when a command is performed the remote may not

generate a command conﬁrmation output or Out of Range output.

This indicates that the system received the command but it was an

incomplete command (e.g. Aux button pressed too short to activate

the trunk release) or it was an illegal message (e.g. the command

was corrupted due to local RF interference). These are temporary nor-

mal functions of the system and remote, perform the command again

within 10 seconds to return to normal operation.

Feature not Available

NOT AVAILABLE

The

message is a generic one which varies in cause

and solution depending upon the command used:

Command

Cause

Reason/Solution

Runtime Reset Remote Start is Off

Sensor Bypass System is not armed

Only available when Remote Start is On

Only available when system is armed

Defroster

Remote Start is Off.

Not configured for

this.

Only available when Remote Start is On.

Only available when configured for

Defroster control.

Download from Www.Somanuals.com. All Manuals Search And Download.

1-way Companion Remote Control

Direct Access

Level

x 1

x 2

x 3

x 4

Button

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Arm/Lock

(Panic)

Silent Arm

Sensor

Bypass

Silent Disarm Remote Valet Car Finder

Sensor Silent Full Silent

Arm

Disarm/

Unlock

Remote Start

Runtime

Reset

Timer Start

AUX 2

Smart Start

AUX 3

Defogger

AUX 4

Aux/Trunk

Not Used

AUX 1

Used to access function levels for Advanced Commands

with multiplier in top row implies button presses)

(

Using the 1 way companion remote

The companion 1 way remote commands the system features as

shown in the previous table, but without the message display of the

Responder LC remote. Siren chirps and parking light ﬂashes are used

to indicate that a command has been received and activated as de-

scribed in the Basic and Advanced command sections.

Accessing Commands

Similar to the Responder LC remote, Basic commands are performed

when a command button is pressed directly. To perform Advanced

Commands press the

levels,

button one to four times to access function

four times.

x4 in the table for example implies pressing

The LED ﬂashes in groups for a few seconds to indicate the level. Press

the desired command button while the LED is ﬂashing to perform the

command.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Auto Lock

When On, the remote control buttons lock if more than 20 seconds

lapses between button presses. If a button is pressed when locked, a

fault tone is emitted. To unlock the buttons; press the button followed

by the

button, the buttons unlock and tones play to conﬁrm.

Car Select

Car 2 must ﬁrst be turned On (See Remote Features menu under “Pro-

gramming” on page 44 to turn on). Press and hold the

button

for 3 seconds. The remote ﬂashes the LED and beeps once or twice to

indicate the selected Car is 1 or 2, release the button for Car Select

or continue to hold for programming.

Release the

button, then press and release while the LED and

beeps continue to perform Car Select. Once the car is selected a com-

mand can be performed by pressing one of the command buttons.

Programming

To enter: Press and hold the

button for eight seconds, the remote

emits one long beep and turns the LED on, the programming main

menu has been accessed (see menu listings below).

To exit: Press and release the

button once, then press and hold the

button again. One short and one long beep is emitted for each

step back, the LED turns off when programming is exited.

1. Sensor Adjust

To avoid unintended alarm triggers, it is recommenced that an

authorized Directed dealer perform all sensor adjustments.

2. Remote Features menu

After entering the programming mode: Press and hold the

button, two LED ﬂashes and beeps indicate the remote features

Download from Www.Somanuals.com. All Manuals Search And Download.

menu is accessed and can be set. Press buttons indicated below,

1beep and ﬂash turns the feature on, 2 beeps and ﬂashes turns

the feature off.

•

Autolock feature: Press

Remote Beeps: Press

Car 2 feature: Press

to turn on/off.

To save and exit the remote feature programming, press the

button once and then press/hold, the transmit LED shuts off con-

ﬁrming exit.

3. Remote Learning

Prepare the the vehicle system to be paired with a new remote.

1. Open at least one of the vehicle’s doors

2. Turn the key to the on position

3. within ﬁve seconds press and release 1 time the control but-

ton on the control center.

4. Within ﬁve seconds press and hold the control button. the

status LED will ﬂash one time and the siren will chirp once to

conﬁrm the system is ready for remote pairing.

5. Release the control button and proceed below.

Note: if pairing does not result within 60 seconds, the system will

exit and the siren will chirp.

Prepare the 1-way remote to be paired with the system.

1. Make sure the remote control is set for the desired car 1 or

car 2 operation.

2. Press/hold the

button on the remote for eight seconds,

the transmit LED comes on, the programming main menu has

been accessed.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Press/hold the

comes on solid.

button until the transmit LED ﬂashes and

4. Press the

button on the remote.

5. Wait several seconds for feedback as the remote generates

a security encryption and sends it to the Control Center. If

pairing is successful the siren will chirp.

If pairing is not successful press and release the

and then repeat steps 3 and 4.

button once

Download from Www.Somanuals.com. All Manuals Search And Download.

System Expansion Options

Controlling two vehicles (Car Select)

The Responder LC and 1way companion remote can control systems

in two different vehicles saving the need for multiple remote controls.

This feature also allows for customized system conﬁgurations on each

vehicle that has more than one driver. See Owner Recognition follow-

ing for details.

Owner recognition

The system can be conﬁgured to recognize the remote used when

disarming and change selected features to match the remote users

preferences. Memory seat adjustment, siren chirps, passive arming,

remote button auto unlocking, alarm output duration can all be custom

set for each remote user at the time of installation.

Comfort closure

Comfort Closure emulates turning the key in the door cylinder or hold-

ing the lock button of an OEM keyless entry. It will automatically close

the windows and sunroof on vehicles with this type of OEM conve-

nience feature.

Alarm output duration

The length of time the siren sounds can be adjusted from 1 to 180

seconds at the time of installation.

Arming and Warn-away chirp control

The system Arm, Disarm and Sensor Warn-away chirps can be conﬁg-

ured for those that prefer a custom silent alarm operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Driver door priority unlocking

The door unlocking operation can be conﬁgured to emulate an OEM

style of driver priority unlocking for added security during disarming.

Auxiliary Channels

The Auxiliary Channel outputs of this system can activate many of the

convenience features found in today’s vehicles. Once a command is

performed to activate a convenience feature the Responder LC dis-

plays text that matches the feature. The system installer can clarify if

any of the below listed features are compatible with your vehicle.

•

Trunk release

Windows open/close

Left Sliding door open/close

Right Sliding door open/close

Rear Hatch open/close

Sunroof open/close

Audio system

Headlights

Download from Www.Somanuals.com. All Manuals Search And Download.

Battery Information (Responder LC)

The Responder LC remote control is powered by an internal recharge-

able battery that can be serviced only through an authorized Directed

Electronics dealer. The information and precautions in this section can

help maximize your battery’s life and usage in providing your Re-

sponder LC remote control with many years of trouble free operation.

Warnings! NEVER use a cable other than the one pro-

vided or plug into an unspeciﬁed source. Injury, severe

damage or explosion may occur when connected to

any other products or used in a way not intended.

Charging the battery when the temperature is below

32°F (0°C) or above 113°F (45°C) may cause severe

battery damage and/or reduce battery life. Avoid

placing the remote control in areas exposed to ex-

treme cold or heat (direct sunlight) when charging the

battery.

Low Battery

After a command is performed the Responder LC and 1way com-

panion remote controls check their battery level and, when the level

requires attention, will begin generating alerts. Once the alerts begin

they will continue to command the system for several days but should

be charged at the earliest opportunity or failure to control the system

may occur.

Low Battery Alerts

When disarming the system using a remote with a low battery the

Download from Www.Somanuals.com. All Manuals Search And Download.

siren will emit one additional chirp as an alert. If conﬁrmation chirps

are programmed off, the system will still emit one chirp as an alert

LOWBAT

when disarming. After performing a command,

and several

beeps play on the Responder LC remote to indicate the battery needs

to be charged.

To preserve power at critically low battery levels the

Responder LC turns the pager off and stops receiving

messages from the system. It will continue to command

the system until the battery can be charged.

Important

Battery Life

The Responder LC remote control has many features that make it one

of the most unique remote controls on the market today, including su-

perior long range communication with the system. The default feature

settings provide for excellent battery charge duration. However, to

maximize this duration between charges, the following suggestions

will help:

•

Turn the remote Off: When not in use and/or out of range of the

vehicle the remote can be turned off in the Main menu.

Turn Paging off: The remote will not wake up to check for mes-

sages with Paging off in the Setup Remote menu. Caution! The

remote will not receive trigger messages from the system.

Turn Beeps off: The Button beeps can be turned off in the Setup

Remote menu. The command beeps still play normally.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Battery Information (1-Way)

The 1-way companion remote is powered by one 3V coin cell lithium

battery (PN CR-2032) that will last approximately one year under

normal use.

Battery Replacement

1. If present, remove the small screw on the back of the remote.

2. Use a small ﬂat blade screwdriver and insert it into the slot locat-

ed along the bottom of the remote, near the key ring. Carefully

pry open the case.

3. Gently slide out the used battery to remove it from the holding

clip. Orient the new battery for the correct polarity and insert

into holding clip.

4. Reposition case parts, and snap together by pressing ﬁrmly and

evenly on the front and back. Reinstall screw (if applicable).

Battery Disposal

Directed cares about the environment. If you need to dis-

pose of the battery, please do so in accordance with your

municipal requirements for battery disposal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary of Terms

Document Terminology

Control Module

The “brain” of your system. Usually hidden underneath the

dash area of the vehicle. It houses the microprocessor which

monitors your vehicle and controls all of the system’s func-

tions.

Responder LC (2-way A hand-held, remote control which operates the various func-

Remote Control)

tions of your system and receives messages and pages from

the system.

Companion Remote A hand-held, remote control which operates the various func-

(1-way Remote Con- tions of your system but does not provide message display..

trol)

Control Center

The control center contains the system’s radio-frequency an-

tenna, the control button, and the Status LED. For maximum

remote-control range, the control center is usually located at

the top of the windshield, centered near the rear-view mirror.

Status LED

A light used to indicate the status of your system. It is located

on your system’s Control Center.

Control Button

A small push button located on your system’s control center.

It is used to override (disarm) the alarm when a remote is not

available or to enter or exit Valet Mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Patent Information

This product is covered by one or more of the following United States

patents:

Remote Start Patents:

5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936;

5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053;

7,483,783

Vehicle Security Patents:

5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591;

5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667;

5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484

Other patents pending.

Download from Www.Somanuals.com. All Manuals Search And Download.

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject to the fol-

lowing two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a

class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio or television,

which can be determined by turning the equipment OFF and ON, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

Remote Controls

To satisfy FCC RF exposure compliance requirements, this device should be

used in hand-held, hand operated conﬁgurations only. The device and its an-

tenna must maintain a separation distance of 20 cm or more from the person’s

body, except for the hand and wrists, to satisfy RF exposure compliance. This

device is designed to be used in a person’s hands and its operating conﬁgu-

rations do not support normal transmissions while it is carried in pockets or

holsters next to a person’s body.

Download from Www.Somanuals.com. All Manuals Search And Download.

Control Center

To satisfy FCC RF exposure compliance requirements, the device and its an-

tenna must maintain a separation distance of 20 cm or more from the person’s

body, except for the hand and wrists, to satisfy RF exposure compliance.

This device complies with the Industry Canada Radio Standards Speciﬁcation

RSS 210. Its use is authorized only on a no-interference, no-protection basis;

in other words, this device must not be used if it is determined that it causes

harmful interference to services authorized by IC. In addition, the user of this

device must accept any radio interference that may be received, even if this

interference could affect the operation of the device.

WARNING! Changes or modiﬁcations not expressly approved by the party re-

sponsible for compliance could void the user’s authority to operate this device.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning! Safety First

Please read the safety warnings below before proceeding. Improper

use of the product may be dangerous or illegal.

Installation

Due to the complexity of this system, installation of this product must only be

performed by an authorized Directed dealer. If you have any questions, ask

your retailer or contact Directed directly at 1-800-753-0600.

Remote Start Capable

When properly installed, this system can start the vehicle via a command

signal from the remote control transmitter. Therefore, never operate the system

in an enclosed area or partially enclosed area without ventilation (such as a

garage). When parking in an enclosed or partially enclosed area or when

having the vehicle serviced, the remote start system must be disabled using the

installed menu wheel. It is the user’s sole responsibility to properly handle and

keep out of reach from children all remote control transmitters to assure that the

system does not unintentionally remote start the vehicle. THE USER MUST IN-

STALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA

ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIV-

ING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STOR-

AGE AREA MUST AT ALL TIMES REMAIN CLOSED. These precautions are the

sole responsibility of the user.

Manual Transmission Vehicles

Remote starters on manual transmission vehicles operate differently than

those with automatic transmission because you must leave your car in neutral.

You must read this Owner’s Guide to familiarize yourself with the proper proce-

dures regarding manual transmission remote starters. If you have any questions,

ask your authorized Directed dealer or contact Directed at 1-800-753-0600.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before remote starting a manual transmission vehicle, be sure to:

•

Leave the vehicle in neutral and be sure no one is standing in front or

behind the vehicle.

•

Only remote start on a ﬂat surface

Have the parking brake fully engaged

WARNING! It is the responsibility of the owner to ensure the parking/emer-

gency brake properly functions. Failure to do so can result in personal injury or

property damage. We recommend the owner have the parking / emergency

brake system inspected and adjusted by a qualiﬁed automotive shop biannu-

ally.

Use of this product in a manner contrary to its intended mode of operation may

result in property damage, personal injury, or death. (1) Never remotely start

the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle

with the keys in the ignition. The user must also have the neutral safety feature

of the vehicle periodically checked, wherein the vehicle must not remotely start

while the car is in gear. This testing should be performed by an authorized

Directed dealer in accordance with the Safety Check outlined in the product

installation guide. If the vehicle starts in gear, cease remote start operation im-

mediately and consult with the authorized Directed dealer to ﬁx the problem.

After the remote start module has been installed, contact your authorized dealer

to have him or her test the remote start module by performing the Safety Check

outlined in the product installation guide. If the vehicle starts when performing

the Neutral Safety Shutdown Circuit test, the remote start unit has not been

properly installed. The remote start module must be removed or the installer

must properly reinstall the remote start system so that the vehicle does not start

in gear. All installations must be performed by an authorized Directed dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN

Download from Www.Somanuals.com. All Manuals Search And Download.

GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPER-

ATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY

RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMME-

DIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF

AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT THE IN-

STALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPON-

SIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

This product is designed for fuel injected vehicles only. Use of this

product in a standard transmission vehicle must be in strict accordance

with this guide.

This product should not be installed in any convertible vehicles, soft or

hard top with a manual transmission. Installation in such vehicles may

pose certain risk.

Interference

All radio devices are subject to interference which could affect proper

performance.

Upgrades and Batteries

Any upgrades to this product and/or installation of batteries must be

performed by an authorized dealer. Do not attempt to perform any

unauthorized modiﬁcations to this product.

Water/Heat Resistance

This product is not designed to be water and/or heat-resistant. Please

take care to keep this product dry and away from heat sources. Any

damage from water or heat will void the warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

Limited lifetime consumer warranty

Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace

(at Directed’s election) with a comparable reconditioned model any Directed unit (hereaf-

ter the “unit”), excluding without limitation the siren, the remote transmitters, the associated

sensors and accessories, which proves to be defective in workmanship or material under

reasonable use during the lifetime of the vehicle provided the following conditions are met:

the unit was purchased from an authorized Directed dealer, the unit was professionally

installed and serviced by an authorized Directed dealer; the unit will be profession¬ally

reinstalled in the vehicle in which it was originally installed by an authorized Directed

dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the

bill of sale or other dated proof of purchase bearing the following information: consumer’s

name, telephone number and address; the authorized dealers name, telephone number

and address; complete product description, including accessories; the year, make and

model of the vehicle; vehicle license number and vehicle identification number. All com-

ponents other than the unit, including without limitation the siren, the remote transmitters

and the associated sensors and accessories, carry a one-year warranty from the date of

purchase of the same. ALL PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR

WITHOUT PROOF OF PURCHASE FROM AN AUTHORIZED DEALER WILL BE DENIED.

This warranty is non-transferable and is automatically void if: the unit’s date code or serial

number is defaced, missing or altered; the unit has been modified or used in a manner

contrary to its intended purpose; the unit has been damaged by accident, unreasonable

use, neglect, improper service, installation or other causes not arising out of defects in

materials or construction. The warranty does not cover damage to the unit caused by

installation or removal of the unit. Directed, in its sole discretion, will determine what con-

stitutes excessive damage and may refuse the return of any unit with excessive damage.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING

BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY

OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF

NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED;

AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY

TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION

WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY

FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED

DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT,

ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT OFFERING A

GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE

AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY

LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT,

DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR

COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR

Download from Www.Somanuals.com. All Manuals Search And Download.

ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM

OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE

SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS

AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE

MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY

LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE UNIT.

DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER,

INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL

DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME, LOSS OF

EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE

LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A

LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO

THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY IS VOID IF THE UNIT

HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED

DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE

USE, NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER

CAUSES NOT ARISING OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.

Some states do not allow limitations on how long an implied warranty will last or the

exclusion or limitation of incidental or consequential damages. This warranty gives you

specific legal rights and you may also have other rights that vary from State to State.

This warranty is only valid for sale of product(s) within the United States of America and

in Canada. Product(s) sold outside of the United States of America or Canada are sold

“AS-IS” and shall have NO WARRANTY, express or implied.

For further details relating to warranty information of Directed products, please visit the

support section of Directed’s website at: www.directed.com

This product may be covered by a Guaranteed Protection Plan (“GPP”). See your

authorized Directed dealer for details of the plan or call Directed Customer Service at

1-800-876-0800.

920-10011-01 2011-06

Download from Www.Somanuals.com. All Manuals Search And Download.

Tektronix Printer Phasershare Printer User Manual
Toshiba Flat Panel Television 65H14 User Manual
Toyota Automobile xA User Manual
Tricity Bendix Refrigerator ERC506 User Manual
Tripp Lite TV Cables S244 000 User Manual
Tripp Lite TV Cables S506 18N User Manual
Troy Bilt Trimmer TB15CS User Manual
Uniden Cordless Telephone DECT4096 User Manual
ViewSonic Projector PJ406D User Manual
Weber Gas Grill 55826 User Manual