Video Cassette Recorder
W-4 1 2
OW NER’S MANUAL
AUTO CLOCK SET
HEAD
VIDEO SYSTEM
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to ship
your VCR. For maximum protection, repack the set as it was originally packed at the factory.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit.
Do not leave rubber or plastic products touching the unit for a long time. They will mar the
finish.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the VCR is exposed to such a change in temperature, moisture may condense on the
cylinder inside, one of its most crucial internal parts. To prevent the VCR from possible
damage, do not use the unit for at least 2 hours when there is an extreme or sudden change
in temperature.
Compatibility
This video cassette recorder (VCR) is compatible with any other VCR bearing the
mark. HQ VHS equipment is also compatible with existing, non-HQ VHS equipment.
®
As an ENERGY STAR Partner, TOSHIBA has determined that this product or
®
product model meets the ENERGY STAR guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS
GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT.
RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect
you if you observe the following procedures for installation, use and servicing. This unit is
fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
ONLY.
1. Read owner’s manual
After unpacking this product, read the owner’s manual carefully, and follow all
the operating and other instructions.
2. Power Sources
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer to the operating
instructions.
3. Grounding or Polarization
This product may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
4. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating, and these
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface. This
productshouldnotbeplacedinabuilt-ininstallationsuchasabookcaseorrack
unless proper ventilation is provided or the manufacturer’s instructions have
been adhered to.
5. Heat
Theproductshouldbesituatedawayfromheatsourcessuchasradiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and
the like.
7. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from
the product.
9. Overloading
Do not overload wall outlets; extension cords, or integral convenience recep-
tacles as this can result in a risk of fire or electric shock.
10. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system
is grounded so as to provide some protection against voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
11. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY
INSTRUCTIONS
12. Lightning
For added protection for this product during storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
13. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
14. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
15. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting of
the product should follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
S3125A
A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the product and cart
combination to overturn.
16. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
18. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
19. Safety Check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
IN TRO DUCTIO N
Variable Speed Playback ................. 20
Provides important notes and general
explanation of the VCR, including names of the
buttons, jacks, etc.
• Picture Search
• Still Picture
• Frame Advance
• Slow-motion Picture
SAFETY PRECAUTIONS .................... 2
IMPORTANT PRECAUTIONS ............. 3
Useful Functions in Tape
Operation ........................................... 22
• Counter Function
• Tape Remaining Time
• Memory Stop Feature
IMPORTANT SAFETY
INSTRUCTIONS................................... 4
Contents .............................................. 7
Identification of Controls ................... 8
• Front Panel
• Remote Control
• VCR Display
• Rear Panel
RECO RDIN G
Explains recording functions.
Recording a TV Program.................. 24
• Basic Recording
• Watching a TV program while
PREPARATIO N
recording another
• Skipping unnecessary scenes while
recording
• Recording off time setting
Timer Program Recording ............... 25
Explains what you need to do before operating
the VCR.
How to Use the Remote Control ...... 10
Connections ...................................... 11
Auto Set Up ....................................... 13
ADDITIO N AL IN FO RMATIO N
Initial Settings Using On-screen
Remote Control
Display ............................................... 14
for TOSHIBA TV’s............................... 28
• Setting the Language
• Optional settings on the SET UP
screen
• Setting the Clock
Storing Channels on the VCR.......... 16
Video Cassette Use .......................... 18
Before Calling Service Personnel ... 29
Specifications ................................... 30
Accessories ...................................... 30
Memo ................................................. 31
LIMITED WARRANTY ....... Back cover
PLAYBACK
Explains variable functions concerning
playback.
Playback ............................................ 19
• Basic Playback
• Double Speed Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Identification of Controls
See the page in
for details.
This manual shows the names of buttons in italics.
Cassette compartment
EJECT
Fro n t Pa n e l
CHANNEL
18
18
POWER
24
14
STOP
19
24
19
Remote
Sensor
REW 19
VCR Display
19
REC
PLAY FF
Re m o te Co n tro l
TV
POWER
14
19
28
To operate your TV
To operate this VCR.
VCR
TV
POWER
CH/TRK
VCR
14
17
Number buttons
1
4
7
2
5
8
0
3
6
100
17
9
EJECT
18
19
100
14 ENTER
REW *
VC-413
PLAY *
19
24
19
20
22
EJECT
SLOW 21
PLAY
TV/VCR
FF *
DISPLAY
22
REW
FF
ENTER
PAUSE/STILL
COUNT RESET
SP/SLP
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
24
I.SELECT
REC
TIMER
REMAIN/COUNTER
I.SELECT
22
24
TIMER
26
27
14
19
PROG. CANCEL
TV VOL
CANCEL
REC
24
28
PROG.
TV VOL
STOP *
* These buttons are used to control the
cursor on the screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR Disp la y
Cassette indicator
Timer recording indicator
TIMER
VCR
VCR indicator
Multifunctional
indicator
Re a r Pa n e l
RF IN (FROM ANT.) terminal
LINE IN AUDIO jack
LINE OUT AUDIO jack
IN
(FROM ANT.)
AUDIO
OUT
IN
RF
OUT
(TO TV)
CH
3
4
VIDEO
LINE IN VIDEO jack
LINE OUT VIDEO jack
To wall outlet
CH selector (3/4)
RF OUT (TO TV) terminal
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
How to Use the Remote Control
This section explains how to get ready for remote control operation.
Se ttin g u p th e Re m o te Co n tro l
Open the battery compartment lid on the
rear panel.
1
Install 2 batteries (“AA” size) following
the polarity diagrams.
2
3
4
Close the battery compartment lid.
Point the remote control at the VCR and press the buttons within the operating range.
Distance: within about 7 m from the front of the remote sensor
Angles: within about 30˚ in every direction
N o te s o n b a tte rie s
Ca rin g fo r th e re m o te co n tro l
• The life of the batteries is about 1 year
depending on the conditions of use.
• If the remote control does not operate
correctly, replace all batteries with new ones.
• Do not expose the remote sensor of the VCR
to a strong light source such as direct sunlight
or illumination (especially high-frequency
lighting) when using the remote control.
• Be careful not to spill water on the remote
control or to place it on anything wet, and avoid
sharp impacts.
• If the remote control is not to be used for a
long period of time, remove the batteries to
avoid possible damage from battery corrosion.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Connections
Before you use this VCR, it is necessary to connect it to your TV. Several ways of connecting are
available depending on your use of TV or cable box. Select one which is applicable to your equipment.
An te n n a / VCR/ TV Co n n e ctio n
Disconnect the antenna cable from your TV and connect it to the RF IN terminal on the
VCR.
1
Connect the RF OUT terminal to the TV.
2
VHF/UHF
UHF antenna
only
VHF antenna
only
combination antenna
IN
(FROM ANT.)
IN
(FROM ANT.)
1
AUDIO
OUT
IN
RF
OUT
(TO TV)
CH
3
4
VIDEO
RF
VHF/UHF
OUT
(TO TV)
2
VHF UHF
Setting the VCR Output Channel
Antenna splitter
(not supplied)
When the VCR is connected in this way, the VCR sends the output
signals to channel 3 or 4 on your TV. Set the output channel
selector (CH selector) of the VCR to “3” or “4”, whichever is vacant
in your area.
AUDIO / VIDEO Co n n e ctio n s
The AUDIO/VIDEO jacks are also available to connect your TV.
W h e n co n n e cte d y o u r TV u sin g th e
AUDIO / VIDEO O UT ja ck s
IN
(FROM ANT.)
AUDIO
OUT
IN
To watch video pictures, set the video input mode
on your TV. For the video input mode, refer to
the manual of your TV.
RF
OUT
(TO TV)
CH
3
4
VIDEO
LINE OUT VIDEO
VIDEO IN
LINE OUT AUDIO AUDIO IN
Ca b le Co n n e ctio n
Choose one of the below according to your usage of the cable box.
Th is se t-u p w ill e n a b le y o u to :
– record an unscrambled channel.
– watch an unscrambled channel while recording it.
IN
(FROM ANT.)
AUDIO
OUT
IN
RF
OUT
(TO TV)
CH
3
4
– record an unscrambled channel while watching
another (only when you connect a cable-
compatible TV).
VIDEO
Yo u w ill n e e d to :
• select TV channel 3 or 4 to receive video signals.
Incoming cable
• to record a channel while watching another, press
TV/VCR on the remote control to turn off the
“VCR” indicator in the VCR display and select a
desired channel on the TV (only when you connect
a cable-compatible TV).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Th is se t-u p w ill e n a b le y o u to :
– record an unscrambled channel.
– watch an unscrambled channel while recording it.
IN
(FROM ANT.)
AUDIO
OUT
IN
– record an unscrambled channel while watching
another (scrambled or unscrambled).
RF
OUT
(TO TV)
CH
3
4
VIDEO
Cable box
Yo u w ill n e e d to :
• set TV channel to the output channel of the cable
box.
Incoming cable
OUT
IN
• turn on the cable box and select cable channel 3
or 4 according to the output channel of the VCR.
• to record a channel while watching another,
press TV/VCR on the remote control to turn off
the “VCR” indicator in the VCR display and select
a desired cable channel on the cable box.
Th is se t-u p w ill e n a b le y o u to :
– watch an unscrambled or scrambled channel
IN
(FROM ANT.)
AUDIO
OUT
IN
while recording it.
RF
OUT
(TO TV)
CH
3
4
VIDEO
– record any channels through the cable box.
Cable box
Yo u w ill n e e d to :
• set TV channel 3 or 4 to receive video signals.
(See page 11.)
• set VCR channel to the output channel of the
cable box, and select a desired cable channel
on the cable box.
OUT
Incoming cable
IN
• while the VCR is turned off or the “VCR”
indicator is not lit in the VCR display, set TV
channel to the output channel of the cable box.
A/B switch
A
A
Th is se t-u p w ill e n a b le y o u to :
B
– watch an unscrambled or scrambled channel
while recording it.
B
Cable box
– record an unscrambled channel while watching
another unscrambled channel (only when you
connect a cable-compatible TV).
IN
(FROM ANT.)
AUDIO
OUT
IN
RF
OUT
(TO TV)
CH
3
4
VIDEO
• A/B switch “A”: record and watch an
unscrambled channel which
comes bypassing the cable
box.
• A/B switch “B”: record and watch a scrambled
or unscrambled channel coming
through the cable box.
Cable box
Th is se t-u p w ill e n a b le y o u to :
– watch or record a channel through the cable
box via the LINE IN (AUDIO/VIDEO) jacks.
IN
(FROM ANT.)
Yo u w ill n e e d to :
AUDIO
OUT
IN
RF
OUT
(TO TV)
CH
3
4
• press I.SELECT so that the VCR display
VIDEO
shows “L”.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Auto Set Up
The VCR’s clock and tuner channels are set automatically when the VCR is plugged into the AC outlet.
Au to Se t u p
VCR
TV
POWER
Plug the VCR into the AC outlet
1
2
1
4
7
2
5
8
0
3
6
“Auto” blink while the VCR automatically sets the clock using
the data broadcast by the local TV stations.
While “Auto” is blinking, channel memory is also set
automatically.
9
100
VC-413
EJECT
PLAY
REW
FF
ENTER
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
CANCEL
When Auto set up has been completed, the VCR is on
standby mode.
3
Notes
• It may takes several minutes during the Auto set-up
• Press CANCEL on the remote control to cancel the auto set-up.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Initial Settings Using On-screen Display
The language selection and clock setting must be set first when VCR is first plugged in or after it
encounters a power failure.
Preparation
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video
connection (page 11).
• Press VCR to set the remote control operating the VCR.
Se ttin g th e La n g u a g e
VCR
VCR
TV
POWER
POWER
Press POWER to turn on the VCR.
1
2
1
4
7
2
5
8
0
3
6
Press PROG..
The following screen appears on the TV.
9
100
VC-413
REW
FF
EJECT
PLAY
REW
FF
ENTER
STOP
PLAY, STOP
ENTER
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
PROG.
Select the language using PLAY or
STOP and press PROG..
The screen turns to the MENU screen.
3
4
MEnU
En
D
:
PROG
ENTER
Press PROG. to return to the normal TV screen.
O p tio n a l se ttin g s o n th e SET UP scre e n
Other optional settings can be made. Press ENTER while “SET UP” is selected on the MENU screen.
The screen turns to the SET UP screen.
TAPE LEnGTH
120 160 180
Page 22
COUnTER MEM on
LA GUAGE
off
ESP
Page 23
n
E
n
G
FRA
To change the language, move down here and set to the desired one.
E
n
D
:
PROG
To exit, press PROG. once.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Se ttin g th e Clo ck
Press ENTER to start the “AUTO” clock
set feature.
After the VCR is turned off, it automatically
updates the clock using the data broadcast
by the local TV stations.
8
9
Example: To set the clock to 2:30 p.m. on
August 25 (summer time) 2001.
Press PROG..
The MENU screen appears on the TV.
1
*The clock is
revised by
CLOCK SET
SUMMER TIME
Select “PRESET” using FF or REW,
and press ENTER.
broadcasting
signal at 8:00 A.M
every morning.
2
TIME ZOnE CH
2
SCAnnI
n
G
nOW
E
n
D
:
PROG
ENTER
CLOCK SET
CH MEMORY
Select the options using FF or REW.
Change the data using PLAY or STOP.
1) Set “SUMMER TIME
E
n
D
:
PROG
ENTER
(Daylight-Saving Time)”.
Press ENTER to select “CLOCK SET”.
3
4
DST start: Daylight-saving time begins on
the first Sunday in April. Because the
clock automatically changes from 2:00 AM
to 3:00 AM (forward one hour).
DST end: Daylight-saving time ends on
the last Sunday in October. The VCR
clock automatically changes from 2:00 AM
to 1:00 AM (back one hour).
remember that any part of a scheduled
Timer Recording that falls between these
two times will not be recorded.
CLOCK SET
SUMMER TIME
TIME ZO
nE CH
P R E S S
T O S T A R T S E T T I
E
n
T E R
n
G
E
n
D
:
PROG
ENTER
Select “AUTO” or “MANU” using PLAY or
STOP.
AUTO: The VCR automatically sets or
adjusts the clock.
If you select “AUTO” mode, proceed to step 8.
MANU: You can set the clock manually.
If you select “MANU” mode, proceed to next
step.
AUTO: the VCR is using the clock data
Broadcast by the local TV stations.
IN: You want to use the DST function, and
you are leaving in the area that apply
Daylight-saving time.
OUT: You are not leaving in the area that
apply Daylight-saving time and you do not
want to use DST function.
2) Set “TIME ZONE”.
Vary the digits to set the hour.
PLAY : To increase.
STOP : To decrease.
5
6
7
If you select “AUTO” for your time zone,
the VCR sets the clock using the first
Coordinated Universal Time information it
finds. If the time is not correct, select
another time zone or use the “MANU”
option.
Move to the next using FF
(To move back, press REW.)
3) Set “CLOCK DATA CH”.
Repeat step 5 and 6 to set the minutes,
month, day, and the year (by the last
two digits).
If you don't know the clock data channel,
select “AUTO”. The VCR will scan
automatically to tune the channel carrying
the clock data.
Proceed to step 10 to start the clock.
If AUTO CLOCK SET is unsuccessful, set the
time and date through the “MANU” clock
set menu selection.
Press PROG..
Now the clock starts.
10
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Storing Channels on the VCR
This section is required if you receive only normal TV or unscrambled cable channels.
In co m in g An te n n a / Ca b le (CATV) Sig n a ls
The VCR scans through all receivable TV and CATV channels and stores only the active
ones in your area into the memory. Once the storing is finished, you can select a desired
channel using CH/TRK.
Preparation
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video
connection (page 11).
• Press I.SELECT so that the channel number will appear if “L” is displayed in the VCR display.
In co m in g An te n n a / Ca b le (CATV) Sig n a ls
Press PROG. to display the MENU screen.
1
VCR
TV
POWER
Select “PRESET” using FF or REW,
and press ENTER.
2
1
4
7
2
5
8
0
3
6
Number
buttons
9
CLOCK SET
100
CH MEMORY
100
VC-413
REW
EJECT
PLAY
FF
E
nD
:
PROG
ENTER
REW
FF
ENTER
STOP
PLAY,STOP
ENTER
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
Select “CH MEMORY” using PLAY
or STOP, and press ENTER.
3
I.SELECT
REC
TIMER
I.SELECT
PROG. CANCEL
TV VOL
TV/CATV
TV
CATV
1,6
AUTO SCAn
ADD CH
OFF
On
- - CH
ERASE CH
- - CH
E
n
D
:
PROG
Set “TV/CATV“ to “TV” or “CATV” using FF or REW.
TV: To store channels received via the antenna.
CATV: To store channels received via the incoming cable.
4
5
Select “AUTO SCAN” using PLAY or
STOP, and press FF to set to “ON”.
The VCR starts scanning and the
channels are stored in the VCR in
ascending order. When the scanning is
finished, the screen automatically
returns.
AUTO SCAn
2
CH
on
E
n
D
:
PROG
Press PROG. twice to exit.
6
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Enter a channel number of 1 to 125 using
number buttons.
For more than 100 number, first press 100.
For CATV channels, refer to the chart below.
(For other orders, check with your cable
company.)
4) Repeat steps 2) and 3) to add or erase
channels as necessary.
Ad d in g o r e ra sin g ch a n n e ls
Adding channels
If a desired channel cannot be scanned
automatically because of a weak signal, it can be
added to the memory.
Erasing channels
You can erase a stored channel from the memory
if it is unnecessary.
5) Press PROG. two times to exit.
1) Follow steps 1 to 3 of “Incoming Antenna/
CATV Signals”.
2) Select “ADD CH” or “ERASE CH” using PLAY
or STOP.
Se le ctin g sto re d ch a n n e ls
Once the active channels have been stored, you
can select the channels in two ways below.
Number buttons
To add channels
To enter digits of the channel number.
• For one-digit number, enter 0 before.
• For more than 100 number, first press 100.
TV/CATV
TV
CATV
AUTO SCAn
ADD CH
ERASE CH
OFF
On
- - CH
- - CH
• Each number button needs to be pressed
within 2 seconds.
TO SET CH PUSH 0~9 KEYS
PROG
E
n
D
:
CH/TRK buttons
To shift up or down the stored channel numbers.
To erase channels
TV/CATV
TV
CATV
AUTO SCAn
ADD CH
OFF
On
- - CH
ERASE CH
- - CH
TO SET CH PUSH 0~9 KEYS
E nD PROG
:
Ch a n n e l re fe re n ce ch a rt
CH NUMBER
TV
CATV STD (HRC/IRC)
1
–
1(A-8)
2
2
2
3
3
3
4
4
4
5
5
6
6
7
7
7
8
8
8
9
9
9
Number on the VCR
Corresponding channel number
5(A-7) 6(A-6)
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
10 11 12 13
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
R
S
T
U
V
W
AA BB CC DD EE FF GG HH II
JJ KK LL MM NN OO
…
…
…
52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69
PP QQ RR SS TT UU VV WW XX YY ZZ AAA BBB 65 66 67 68 69 70 71
–
–
…
…
…
93 94 95 96 97 98 99 100 101 102 103
121 122 123 124 125
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
93 94 A-5 A-4 A-3 A-2 A-1 100 101 102 103
121 122 123 124 125
CATV signals
• STD (standard) cable TV signals
• HRC (Harmonic Related Carriers) cable TV signals
• IRC (Incremental Related Carriers) cable TV signals
IRC is also called ICC (Incremental Coherent Carriers)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Video Cassette Use
Vid e o Ca sse tte Use
Lo a d in g a ca sse tte
Push the cassette into the cassette compartment with the window side facing up and the
label side towards the front. The VCR is automatically turned on. The
appear in the VCR display.
indicator will
Eje ctin g a ca sse tte
Press EJECT. The cassette is ejected from the cassette compartment.
Warning
Do not insert your hands or any foreign objects into the compartment. This may result
in injury or damage. Take special care with children to avoid accidents.
Pre ca u tio n s w h e n u sin g vid e o ca sse tte s
Video cassettes have a safety tab to prevent accidental erasure. If the tab has already been removed,
recording cannot be performed.
To prevent accidental erasure
To record again
Remove this safety tab with a screwdriver.
Cover the tab hole with adhesive tape.
• Avoid exposing cassettes to direct sunlight. Keep them away from heaters.
Avoid extreme humidity, vibrations or shock, strong magnetic fields (near a motor, transformer or
magnet) and dusty place.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Playback
This section explains the basic playback operation.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Press VCR to set the remote control operating the VCR.
Ba sic Pla y b a ck
VCR
TV
POWER
Load a recorded cassette.
Power is turned on.
If the cassette has no safety tab,
playback starts automatically.
1
TIMER
REC
1
4
7
2
5
8
0
3
6
S
L
P
S
CH/TRK
L
VCR
9
100
VC-413
Press PLAY to start playback.
EJECT
2
3
2
PLAY
ST
FF
REW
FF
ENTER
STOP
L
VCR
REW
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
3
To stop playback, press STOP.
I.SELECT
REC
TIMER
TIMER
REC
S
PROG. CANCEL
TV VOL
L
VCR
Do u b le Sp e e d Pla y b a ck
Press PLAY during playback.
A tape runs at double speed
playback.
1
To resume normal playback Press PLAY
Re w in d in g / Fa st-fo rw a rd in g
Press REW or FF in the stop mode.
Ad ju stin g th e tra ck in g
When playback starts, the VCR automatically adjusts the tracking for clear pictures and sound
(Digital Auto Tracking).
If the VCR cannot locate the best possible tracking point, hold down one of CH/TRK to adjust the
tracking manually.
Notes
• During the adjusting, the playback picture and sound may be distorted.
• The digital auto tracking is activated only in the playback mode.
• The noise on the screen may not be completely eliminated depending on the tape used, especially when the
tape was recorded on another VCR.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Variable Speed Playback
You can play back a tape at various tape speeds.
Pictu re Se a rch
A tape runs at 5 times or 7 times the normal playback speed so
that you can quickly locate a particular scene.
VCR
TV
POWER
1
4
7
2
5
8
0
3
6
Press FF or REW during playback.
1
9
100
The tape runs at 5 times the normal playback speed.
VC-413
PLAY
EJECT
PLAY
To change the tape speed to 7 times the normal playback
speed, press and hold FF or REW.
2
FF
REW
REW
FF
ENTER
STOP
PAUSE/STILL
SLOW
If you release it, the tape speed returns to 5 times.
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
Note
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
If you press FF or REW during picture search, the mode changes to fast-
forwarding or rewinding.
To re su m e n o rm a l p la y b a ck
Press PLAY.
Still Pictu re
A picture freezes so that you can watch closer.
Press PAUSE/STILL during playback.
The picture freezes.
1
To re su m e n o rm a l p la y b a ck
Press PAUSE/STILL again.
Notes
• The still mode is automatically cancelled after about 5 minutes and returns to
normal playback.
• The still picture may shake if a picture of a fast-moving object or scene is
frozen. This is not a defect in the unit.
Ad ju stin g Still Pictu re Sta b ility
If the still picture is distorted or flickers, hold down one of CH/TRK until
the picture becomes stable.
Note
The distortion of the still picture may not be eliminated completely.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Fra m e Ad va n ce
A picture advances frame by frame.
Press PLAY during still playback.
Each time you press PLAY, the picture advances one frame.
1
To re su m e n o rm a l p la y b a ck
Press PAUSE/STILL.
Slo w -m o tio n Pictu re
The tape runs at 1/7th or 1/15th the normal playback speed.
Press SLOW during playback.
The tape runs at about 1/7th the normal playback speed.
1
Each time you press SLOW, the speed alternates between 1/7th and
1/15th.
To re su m e n o rm a l p la y b a ck
Press PLAY.
Notes
• The slow-motion picture mode is automatically cancelled after about 5
minutes and returns to normal playback.
• The slow-motion picture may flicker up and down. This is not a defect in the
unit.
Ad ju stin g th e Tra ck in g Ma n u a lly
If the slow-motion picture is noisy, hold down one of CH/TRK until the
best picture is obtained.
Note
The noise in the slow-motion picture may not be eliminated completely.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Useful Functions in Tape Operation
These functions will help your playback.
Co u n te r Fu n ctio n
You can view the clock, linear time counter or tape remaining
time in the VCR display or on the TV screen.
VCR
TV
POWER
1
4
7
2
5
8
0
3
6
Each time you press REMAIN/COUNTER, the VCR display
changes in sequence as follows:
9
100
VC-413
ENTER
PLAY
EJECT
→ Linear time counter → Tape remaining time (RT) → Clock
PLAY
REW
FF
ENTER
STOP
FF
REW
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
STOP
COUNT RESET
REMAIN/
COUNTER
The indication above will also appear on the TV screen by pressing
DISPLAY. They are switchable with REMAIN/COUNTER.
REMAIN/
COUNT
RESET
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
To re se t th e lin e a r tim e co u n te r to “ 0 :0 0 :0 0 ”
PROG.
DISPLAY
The counter is automatically reset to “0:00:00” when a cassette is
ejected. If you want to reset at another point, such as the beginning of a
new recording, just press COUNT RESET.
Notes
• The linear time counter does not work on non-recorded portions on the tape.
• When the tape is ejected or the VCR is turned off, the display changes to
clock.
• If the tape rewinds back over “00:00”, “–” appears in the VCR display.
• The displayed time of the linear time counter is only an approximation.
Ta p e Re m a in in g Tim e
To view the tape remaining time in the VCR display, select the
tape length beforehand.
Turn on the VCR and load a cassette.
1
Press PROG. to display the MENU screen.
2
Select “SET UP” using FF or REW, and press ENTER.
3
Select the length of the tape, using
FF or REW.
4
TAPE LE
nGTH
120 160 180
T120: for a T-120 tape or shorter
T160: for a T-140 or T-160 tape
T180: for a T-180 tape
COUnTER MEM on
LAnGUAGE EnG FRA
off
ESP
E
n
D
:
PROG
Press PROG. to exit.
5
Press REMAIN/COUNTER.
The remaining time (“RT - : - -”) appears in the VCR display.
6
Notes
• The displayed remaining time is an approximation.
• The remaining time is calculated according to the tape speed (SP or SLP)
and the cassette type.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Me m o ry Sto p Fe a tu re (Ze ro Re tu rn )
On the SET UP screen, select
VCR
TV
POWER
1
“COUNTER MEM.” using PLAY or
STOP, and set to “ON” using
REW or FF.
1
4
7
2
5
8
0
3
6
TAPE LEnGTH
COUnTER MEM on
LA GUAGE
120 160 180
9
off
ESP
100
n
E
n
G
FRA
VC-413
ENTER
PLAY
EJECT
PLAY
E
n
D
:
PROG
REW
FF
ENTER
STOP
FF
REW
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
STOP
REMAIN/
COUNT
RESET
Press PROG. to exit.
2
COUNT RESET
REMAIN/
COUNTER
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
The memory-stop feature allows you to quickly return to a
PROG.
counter reading of “0H00M00S” from any point on the tape.
Memory stop is automatically turned on whenever the time
counter with memory is displayed on the TV screen. This is
convenient when you want to watch a segment of the tape
repeatedly. You may also discover other useful application for
this feature.
DISPLAY
Notes: If you are rewinding the tape and the VCR stops at
“0H00M00S M”, press REW again to continue
rewinding.
If you press the FF (fast-forward) button and the time
counter never reaches “0H00M00S M” between that
point and the end of the tape, the VCR will continue to
fastforward to the end of the tape.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Recording a TV Program
This section explains the basic recording operation.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
Ba sic Re co rd in g
VCR
TV
POWER
1
4
7
2
5
8
0
3
6
Load a cassette with the safety tab attached.
1
2
3
9
Press TV/VCR so that the “VCR”
100
indicator appears in the VCR display.
VC-413
VCR
EJECT
PLAY
2
REW
FF
ENTER
STOP
Select a channel to record with
CHANNEL on the VCR, or CH/TRK
or number buttons on the remote
control.
If you see “L” in the VCR display, press I.SELECT so that the channel
number appears.
3
H
ST
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
L
VCR
S
REMAIN/
COUNT
RESET
6
4
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
5
I.SELECT
• If you record cable channels via the cable box, make the output
channel number of the cable box or “L” appear, depending on your
connection. (See pages 11 – 12.)
Press SP/SLP to select the
recording tape speed.
4
TIMER
S
REC
L
VCR
SP: Suitable for general recording with
better picture and sound quality.
SLP: Suitable for tripling recording time, but with less picture and
sound quality than using the SP tape speed.
To record from other
connected equipment
In step 3, press I.SELECT to
switch the display as follows:
L: To record via the LINE IN
jacks on the rear panel.
.
REC
TIMER
Press REC on the VCR, or
simultaneously press both REC on
the remote control.
5
6
TIMER
S
L
VCR
Recording starts.
Press STOP to stop recording.
Wa tch in g a TV p ro g ra m w h ile
re co rd in g a n o th e r
Re co rd in g o ff tim e se ttin g
By setting the recording off time, the recording
stops and the VCR is turned off automatically.
1) While recording, press TV/VCR to turn off
“VCR” indicator.
2) Choose another channel using the channel
selector on the TV.
While recording, press simultaneously both REC
on the remote repeatedly to set the desired off
time.
Each time you press REC, each half-hour up to
about 4 hours appear cyclically.
Sk ip p in g u n n e ce ssa ry sce n e s w h ile
re co rd in g
Hi-Fi
TIMER
STEREO
Press PAUSE/STILL to stop recording
momentarily. To resume recording, press
PAUSE/STILL again.
L
R
VCR
SAP
Notes
Note
• To cancel the recording in progress, press
The VCR automatically shifts to the stop mode if the
recording pause mode continues for 10 minutes.
POWER on the VCR.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Timer Program Recording
The programmable timer allows you to record up to 6 different programs over one month.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Make sure that the clock is set correctly (page 15).
• Store the channels on the VCR (pages 16 and 17).
Tim e r Pro g ra m m in g Pro ce d u re
Example: To record cable channel 25 in the SP tape speed from
VCR
TV
POWER
9:20 p.m. until 10:00 p.m. on August 30. Today is August 25.
Number
buttons
1
4
7
2
5
8
0
3
6
Load a cassette with the safety tab attached.
1
9
100
Press PROG. to display the MENU screen.
2
PLAY
VC-413
ENTER
EJECT
Select “PROGRAM” using FF or
REW, and press ENTER.
3
PLAY
REW
REW
FF
ENTER
STOP
FF
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
I.SELECT
REC
TIMER
10
PROG. CANCEL
TV VOL
2,9
Move to the next using FF, and
4
select the channel number 25 by
pressing number buttons 2 and 5,
PLAY or STOP.
• You can make “L” appear on the channel number position by
pressing I.SELECT depending on your connection.
(See pages 12 ).
To make corrections:
Press REW to move back to the item, or FF to forward.
(Continued)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer Program Recording (continued)
Move to the next using FF, and set
the recording date using PLAY or
5
STOP.
The date changes as follows:
…
…
→ 8/25 → 9/25 →
→ 7/25 → WKLYSU →
MO~FR ← WKLYSA ←
…
[WKLYSU] [WKLYSA]: You can record TV programs on the same
channel on the day and time every week.
[MO~FR]: You can record TV programs on the same channel on the
day and time Monday through Friday.
Move to the next using FF, and set
the hour and minutes of the
recording start time.
6
7
8
P
M
Move to the next, and set the
recording off time.
Move to the next, and select the
tape speed (SP) using PLAY or
STOP.
For the tape speed “AUTO (Auto Speed
Select)”, see below.
To set another program, press FF, and
select the next line pressing STOP.
Repeat steps 4 to 8.
Press PROG..
Now programming is completed.
9
REC
TIMER
Press both TIMER simultaneously.
The power turns off and the VCR enters
the timer standby mode.
10
TIMERHi-Fi
STEREO
L
SAP
Notes
Au to Sp e e d Se le ct
• Make sure that the tape length is selected correctly
according to the tape used on the SET UP screen
(page 22).
• When the SLP tape speed is selected and the tape
length is not sufficient to record the program to the
end, the program cannot be recorded to the end.
• The picture will be distorted when playing the part
where the recording tape speed is switched from
SP to SLP with the Auto Speed Select feature.
If you are not sure the tape is long enough for
timer program recording in the SP tape speed,
set the recording tape speed to “AUTO”.
Recording starts in the SP tape speed and the
VCR automatically selects the tape speed to
record the program to the end. If the tape length
is not long enough, the tape speed automatically
changes from SP to SLP.
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n firm in g th e tim e r p ro g ra m s
If th e p o w e r fa ilu re o ccu rs d u rin g
th e tim e r p ro g ra m re co rd in g
Press PROG. during timer recording mode.
• When a power failure has occurred, “--:--”
appears in the VCR display. Since the
programmed contents have been cleared,
reset the clock and timer programming.
• When power has failed for a short time, the
color of the current time display blinks.
The programmed contents are not affected.
Reset the clock.
The screen for confirming will appear.
P
P
M
M
O ve rla p s o f th e p ro g ra m s
Press. PROG. again to exit from confirmation
page.
If two timer programs overlap, the recording
start time of program 1 has priority over the
recording off time of program 2.
Ch a n g in g / ca n ce llin g th e tim e r
p ro g ra m s
Program 1
(Start time)
1) If the TIMER indicator is lit, press both TIMER
to turn it off, and then turn the VCR on by
pressing VCR POWER.
Program 2
(Start time)
Overlapped portion
(not recorded)
2) With steps 2 to 9, change the items.
To cancel a program, select the program you
want to cancel in step 4, and press CANCEL.
The line is then cleared.
3) Press both TIMER to return to the timer
standby mode.
Erro r in d ica tio n
The “--E--” ( Error ) indicator appears in the VCR
display if you press both TIMER when:
–– a cassette is not loaded.
–– the loaded cassette has no safety tab.
–– timer recording is in progress .
In these cases, a recording can not be made.
To Ca n ce l th e Tim e r Re co rd in g
By pressing the POWER button on the front
panel of the VCR, it will cancel the timer
recording and go to standby.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION
Remote Control for TOSHIBA TV’s
The remote control can control TOSHIBA TV’s.
TO SHIBA TV’s co n tro l
1
VCR
TV
POWER
POWER
Press TV to set the remote control operating your TV.
1
1
4
7
2
5
8
0
3
6
CH/TRK
2 Point the remote control at your TV and use each button
9
listed below to make sure that your TV is operate correctly.
100
100
Number
buttons
VC-413
POWER
CH/TRK
TV VOL
I.SELECT
To turn the TV on or off
To select TV channels in the upper or lower direction.
To adjust the sound level.
EJECT
PLAY
REW
FF
ENTER
STOP
ENTER
To select an external source such as a VCR.
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
Number buttons To select TV channels. When selecting channels
DISPLAY
I.SELECT
I.SELECT
REC
TIMER
1 to 9, enter 0 and then the desired number.
PROG. CANCEL
TV VOL
100
DISPLAY
ENTER
To substitute for 100 channel key
To turn on or off TV’s screen display.
To use for the TV’s ENTER key.
TV VOL
Important
Some TV’s may not respond to all
the operations above, or may not
be operated at all with this remote
control. In this case, operate your
TV’s with it’s own remote control.
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION
Before Calling Service Personnel
Check the following symptoms before requesting servicing.
N o p o w e r.
Th e tim e r re co rd in g fu n ctio n d o e s n o t
w o rk .
• There is an error in programming.
• The power cord is not plugged in.
– Plug the power cord into the outlet firmly.
– Reset the timer recording program. (page 27)
Alth o u g h th e p o w e r is o n , th e VCR w ill
n o t w o rk .
• There is no cassette in the VCR.
– Load a cassette with the safety tab attached.
(page 18)
• There is no cassette.
– Load a cassette. (page 18)
• The cassette does not have the safety tab.
– Use another cassette with a safety tab or
Th e clo ck d o e s n o t w o rk .
• There has been a power failure.
cover the hole with adhesive tape. (page 18)
– Reset the clock. (page 15)
• The timer indicator is not displayed.
– Press both TIMER simultaneously. (page 26)
Th e tim e r d o e s n o t w o rk p ro p e rly.
• The time is incorrect.
• There has been a power failure.
– Set the clock correctly. (page 15)
– Reset the clock. (page 15)
Th e p ictu re d o e s n o t a p p e a r o n th e TV
scre e n .
Th e re m o te co n tro l d o e s n o t w o rk
p ro p e rly.
• The video channel or video input mode is not
• The batteries are exhausted.
set correctly.
– Replace all batteries. (page 10)
– Set the TV channel to the video channel (3 or
4) or set the video input mode on the TV.
(page 11)
• The remote control is operated beyond the
operating range.
– Make sure the remote control is within 30° of
• The TV signal is weak.
the remote sensor on the VCR. (page 10)
– Adjust the antenna direction or use an
optional antenna booster.
• Too far from the VCR.
– Use the remote control within 7 m from the
front of the VCR. (page 10)
• The power cord is not plugged in.
– Plug the power cord into the outlet firmly.
• An obstacle may be in the way of the operation.
– Remove the obstacle.
Th e p ictu re d o e s n o t a p p e a r o n th e TV
scre e n d u rin g re co rd in g a n d p la y b a ck .
• The operating mode of the remote control is not
• The video channel or VCR mode is not set
set correctly.
correctly.
– Press VCR or TV depending on the
– Press TV/VCR to select the VCR mode and
equipment you want to operate. (pages 14)
set the TV channel to 3 or 4. (pages 11, 24)
Th e ca sse tte is e je cte d im m e d ia te ly a fte r
it is lo a d e d .
Th e VCR d o e s n o t re co rd .
• The loaded cassette has no safety tab.
• The cassette was inserted with the label side
not paralleling the compartment.
– Use a cassette with a safety tab or cover the
hole with adhesive tape. (page 18)
– Reload it carefully. (page 18)
Th e p la y b a ck p ictu re is p o o r.
Th e ca sse tte d o e s n o t g o in to th e ca sse tte
co m p a rtm e n t.
• Tracking is not set appropriately.
– Adjust the tracking manually. (page 19)
• There is already a cassette in the VCR.
– Eject the cassette and reload the new one.
(page 18)
• The video heads are dirty.
– Clean the video heads with a commercially
available cleaning tape.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power Supply:
120 V AC, 60 Hz
Power consumption:
External dimensions:
Mass:
16 W
360 x 94 x 252mm (W.H.D.)
3.0 kg
Channels received:
VHF: Channels 2–13
UHF: Channels 14–69
CATV: Channels A7-A1,A-CCC, 66-125
UHF/VHF: 75 Ω F type connector
Standard NTSC
Antenna input/output terminals:
Signal system:
Recording/Playback system:
Recording: VHS format (SP, SLP)
Playback: VHS format (SP, LP, SLP)
Cassette:
Video cassette with
mark
Tape speed:
Video recording/playback time:
SLP: 11.1 mm/s, SP: 33.4 mm/s
SLP: 480 minutes, SP: 160 minutes (When T-160
video cassette is used.)
Fast forward/rewind time:
Video input:
Within approx. 60 s (When T-120 video cassette is used.)
1 V (p-p), 75 Ω, unbalanced, negative sync., pin
jack
Video output:
1 V (p-p), 75 Ω, unbalanced, negative sync., pin
jack
Audio input:
Line input: 308 mV (rms), more than 47 kΩ, pin
jack
Audio output:
Line output: 308 mV (rms), less than 4.7 kΩ, pin
jack
Utilization conditions:
Temperature: 5°C to 40°C
Humidity: less than RH 80%
Accessories
Antenna cable ....................................... 1
Remote control..................................... 1
Batteries (AA)....................................... 2
Designs and specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
TOSHIBA VIDEO CASSETTE RECORDER
Toshiba America Consumer Products, Inc. (“TACP”)
Your Responsibility
and Toshiba Hawaii Inc. (“THI”) make the following
limited warranties. These limited warranties extend
to the original consumer purchaser or any person
receiving this set as a gift from the original consumer
purchaser and to no other purchaser or transferee.
The above warranties are subject to the following
conditions:
(1) You must retain your bill of sale or provide other
proof of purchase.
(2) You must notify an Authorized TACP/THI Service
Station within thirty (30) days after you discover a
defective product or part.
Limited Ninety (90) Day Warranty
TACP/THI warrant this product against defects in
materials or workmanship for a period of ninety days
after the date of original retail purchase. During this
period, TACP/THI will repair a defective product or
part, withoutchargetoyou. Youmustdelivertheentire
product to a TACP/THI Authorized Service Station.
Youareresponsibleforalltransportationandinsurance
charges for the set to and from the Authorized Service
Station.
(3) All warranty servicing of this product must be
madebyanAuthorizedTACP/THIServiceStation.
(4) These warranties are effective only if the product is
purchased and operated in the U.S.A or Puerto
Rico.
(5) Labor service charges for set installation. Set up,
adjustment of customer controls and installation
of repair or antenna systems are not covered by
this warranty. Reception problems caused by
inadequate antenna systems are your
responsibility.
Limited One (1) Year Warranty
TACP/THI further warrant the parts in this product
against defects in materials or workmanship for a
period of one (1) year after the date of original retail
purchase. During this period, TACP/THI will replace a
defective part without charge to you, except that if a
defective part is replaced after ninety (90) days from
the date of the original retail purchase, you pay labor
charges involved in the replacement. You must also
deliver the entire product to a TACP/THI Authorized
Service Station. You are responsible for all
transportation and insurance charges for the set to
and from the Authorized Service Station.
(6) Warranties extend only to defects in materials or
workmanship as limited above and do not extend
to any product or parts which have been lost or
discarded by you or to damage to products or
partscausedbymisuse,accident,damagecaused
by Acts of God, such as lightning or fluctuations in
electric power, improper installation, improper
maintenance or use in violation of instructions
furnished by us; or to units which have been
alteredormodifiedwithoutauthorizationofTACP/
THI or to damage to products or parts there of
which have had the serial number removed,
altered, defaced or rendered illegible.
(7) Atyouoption,afterthewarrantyperiodhasexpired
in the U.S.A. Call (800)-631-3811 to receive
information concerning an exchange price.
Payment must be enclosed with the product in the
form of a certified check or money order and
forward your product to:
Rental Units
The warranty for rental units begin with the first rental
or thirty (30) days from the date of shipment to the
rental firm, whichever comes first.
Commercial Units
Products sold and used for commercial use have a
Toshiba America Consumer Products Inc.
limited ninety (90) day warranty for all parts and labor.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Owner’s Manual and Demographic Card
Youshouldreadtheowner’smanualthoroughlybefore
operating this product. You should complete and mail
the enclosed Demographic card within ten (10) days
afteryou, orthepersonwhohasgivenyouthisproduct
as a gift, purchased this product. This is one way to
enable TACP/THI to provide you with better customer
service and improved products. Failure to return the
card will not affect your rights under this warranty.
(8) Upon receipt we will, at our option, replace your
unit with a new or refurbished unit of equal value.
Features may not be identical to your original
product.
(9) Physically damaged units are not acceptable for
repairorexchangeinoroutofwarrantyandwillbe
returned as received.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY (continued)
How to Obtain Warranty Service
(1)Refer to the troubleshooting guide in your owner's manual. This check list may solve your problem.
(2)Call the TACP toll free number 800-631-3811 within (30) days after you find a defective product or part.
(3)Arrange for the delivery of the product to the Authorized TACP/THI Service Station. Products shipped to
the Service Station must be insured and safely and securely packed, preferably in the original shipping
carton, and a letter explaining the defect and also a copy of the bill of sale or other proof of purchase must
be enclosed.
In Hawaii contact
Toshiba Hawaii
In the Continental United States contact:
327 Kamakee Street,
Honolulu, HA 96814
Toll Free
(808)-591-8377
800-631-3811
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular
purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any
warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other
warranties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair
or replacement of any parts. In no event shall TACP/THI be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these
warranties in any manner whatsoever. The time within action must be commenced to enforce any obligation of
TACP/THI arising under the warranty or under any statute, or law of the United States or any state thereof, is hereby
limited to ninety (90) days from the date you discover or should have discovered the defect. This limitation does
not apply to implied warranties arising under state law. This warranty gives you specific legal rights and you may
also have other rights which may vary from state to state. Some states do not allow limitation on how long an
implied warranty lasts, when an action may be brought or the exclusion or limitation of incidental or consequential
damages, so the above provisions may not apply to you.
ATTENTION CANADIAN CONSUMERS:
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed
and forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate”
their warranty. Product must be purchased from an Authorized Canadian Dealer.
Products purchased in the U.S.A and used in Canada are not covered by these warranties.
IMPORTANT: PACKING AND SHIPPING INSTRUCTION
When you send the product to a Service Station, you should use the original carton box and packing material, then
insert the original carton box containing the unite into another carton, using more packing material.
Printed in Indonesia
AC68-01085A
Download from Www.Somanuals.com. All Manuals Search And Download.
|