Quick Installation Guide
TEW-653AP
1.01
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Before You Start
Package Contents
?
TEW-653AP
Multi-Language Quick Installation Guide
CD-ROM (User’s Guide)
Cat. 5 Ethernet Cable (1m / 3.3ft.)
Power Adapter (12V DC, 1A)
Mounting Kit
?
?
?
?
?
System Requirements
?Web Browser: Internet Explorer (6.0 or higher)
?A computer with a network adapter properly installed.
?A network Switch or Hub with an available network LAN port.
?Power over Ethernet (PoE) Switch (e.g. TPE-80WS) (Optional)
?Injector (e.g TPE-111GI ) (Optional)
Note:
The TEW-653AP only works with Power over Ethernet (PoE) devices that follow the
IEEE 802.3af standard.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Hardware Installation
Note: Locate an optimum location for the Access Point. The best place for the Access
Point is usually at the center of your wireless network. Please connect the computer
configuring the TEW-653AP to the same switch/hub.
1. Run a RJ-45 cable and the power adapter
through the cable clip on the TEW-653AP.
2. Connect the RJ-45 cable from the Switch/Hub
to the LAN port on the Access Point.
3. Connect the Power Adapter to the Access Point
and then to a power outlet.
4. Verify that the wireless, LAN and power LEDs
are on.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Power-over-Ethernet Installation
Using the TEW-653AP with a PoE switch
1. Connect a RJ-45 cable from the Power-Over-
Ethernet Switch (e.g. TRENDnet TPE-80WS) to
the LAN port on the Access Point.
2. Verify that the wireless, LAN and power LEDs
are on. Please refer to step 4 in the Hardware
Installation section.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TEW-653AP with the TPE-111GI
1. Connect the Power Cord to the Power
Adapter.
2. Connect the Power Adapter to the DC 48V IN
connector on the TPE-111GI. Then connect
the Power Cord to an outlet.
3. Connect a CAT-5 cable from a switch to the
TPE-111GI's DATA IN port.
4. Connect a CAT-5 cable from the TEW-653AP's
LAN port to the TPE-111GI's PoE Out port.
5. Verify that the wireless, LAN and power LEDs
are on. Please refer to step 4 in the Hardware
Installation section.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Configure the Access Point
Note: It is recommended that you configure the Access Point from a wired computer.
Before the Access Point can be configured, a Static IP address must be assigned to
your computer's network adapter in the subnet of 192.168.10.X. Since the Access
Point's default IP address is 192.168.10.100, make sure no other network devices are
assigned an IP address of 192.168.10.100. (Refer to Troubleshooting section on how to
configure TCP/IP settings on your PC.)
1. Open your web browser, type
http://192.168.10.100 in the Address bar, and
then press Enter.
2. Enter the User name and Password, and then
click OK. By default:
User Name: admin
Password: admin
3. Click Wizard.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Click Next.
5. Select AP Mode and then click Next.
Note:
1. To protect your network from any unauthorized access it is recommended to enable
wireless encryption.
2. The examples below are for WPA2-PSK security. If you select WPA-PSK or
WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your
wireless adapters do not support WPA or WPA2, then select WEP.
6. Use your mouse to select the desired security
level (lowest for no encryption, highest for
WPA2-PSK).
7. Enter the desired SSID and Key. Then click
Next. By default, the SSID is TRENDnet653.
8. Setup is successful. Click Reboot.
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Wait 24 seconds while the Access Point
reboots.
10. Click System -> LAN. Configure the LAN
settings to match your network settings and
then click Apply.
11. Wait 14 seconds while the Access Point
reboots.
Your configuration is complete
For detailed information regarding the TEW-653AP’s configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide CD-ROM, or TRENDnet's website
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
Thank you for choosing TRENDnet
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Mounting
1. Use the mounting plate as a template and mark
the wall for the correct screw position.
2. Drill holes for the screws at the marked
positions on the wall.
3. Use the provided wood screws to secure the
mounting plate to the wall.
4. Align the TEW-653AP with the mounting plate
5. Follow the arrow to secure the TEW-653AP to
the mounting plate.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
How do I configure TCP/IP settings on my computer?
Windows Vista
1. Go into the Control Panel, click Network and
Internet, click Network and Sharing Center,
click Manage Network Connections and then
right-click the Local Area Connection icon and
then click Properties.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Use
the following IP address, and make sure you
assign your network adapter an IP address in
the subnet of 192.168.10.x.
Windows XP/2000
1. Go into the Control Panel, double-click the
Network Connections icon and then right-click
the Local Area Connection icon and then click
Properties.
2. Click Internet Protocol (TCP/IP) and then click
Properties. Then click on Use the following
IP address, and make sure you assign your
network adapter an IP address in the subnet of
192.168.10.x.
says “The page cannot be displayed.” How can I get into the TEW-653AP's web
configuration page?
1. Check your hardware settings again by following the instructions in section 2
2. Make sure the wireless, LAN and power LEDs are lit.
3. Make sure the TCP/IP settings are configured properly (see first question).
4. Since the Access Point's default IP address is 192.168.10.100, make sure that no
other network devices are assigned an IP address of 192.168.10.100.
5. Reset the TEW-653AP. Take a pin or paper clip and press the reset button for 15
seconds. The reset button is located on top of the TEW-653AP.
Download from Www.Somanuals.com. All Manuals Search And Download.
If my network's IP is different than the Access Point's range, what should I do?
You should still configure the Access Point first. After all the settings are applied, go to the
Access Point's configuration page, click on System, click on LAN and change the IP address
of the Access Point to match your network's IP.
After I successfully configured the Access Point to match my network settings, I can not
connect to my network using wireless computers.
If you have a DHCP server in your network, you need to go into TCP/IP settings again and
re-select "Obtain an IP address automatically" to allow the PC to regain an IP address from
your DHCP server.
All the settings are correct, but I can not make a wireless connection to the Access Point.
1. Double check that the wireless LED on the Access Point is lit.
2. Power cycle the Access Point. Unplug the power to the Access Point. Wait 15 seconds,
then plug the power back in.
3. Contact the manufacturer of your wireless network adapter. Make sure the wireless
network adapter is configured with the proper SSID. The default SSID of the Access Point
is TRENDnet653.
The TEW-653AP does not power on when I plug the device into a Power-Over-Ethernet
switch or splitter. What should I do?
1. Verify that the TEW-653AP powers up using the provided 12V, 1A power adapter.
2. Power cycle the PoE switch.
3. Unplug power to the switch, wait 15 seconds, then plug the power back in.
4. Plug the device into a different port on the PoE switch.
5. Try using another Cat-5e cable.
If you still encounter problems or have any questions regarding the TEW-653AP, please contact
TRENDnet's Technical Support Department.
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Tips
The following are some general wireless tips to help minimize the impact of interference within an
environment.
Assign your network a unique SSID
Do not use anything that would be identifying like “Smith Family Network”. Choose
something that you would easily identify when searching for available wireless networks.
Do not turn off the SSID broadcast
The SSID broadcast is intended to be on and turning it off can cause connectivity issues.
The preferred method of securing a wireless network is to choose a strong form of encryption
with a strong and varied encryption key.
Note: after setting up the SSID, encryption type and encryption key/passphrase, please
make a note of them for future reference. You will need this information to connect your
wireless computers to the wireless router/access point.
Change the channel
Most wireless access points and routers are defaulted to channel 6. If you have a site survey
tool that will display the channels you can plan your channel selection around neighboring
access points to minimize interference from them. If your site survey tool does not display
the channel try using channels 1 or 11.
Change the channel bandwidth
If you are using an 802.11n router or access point you can also make the following changes.
Change the channel bandwidth to 20/40MHz. This will provide the highest possible
performance using an 802.11n device. Also, if using 802.11n you should be securing the
network with WPA2 security.
Note: Due to Wi-Fi certification considerations if you choose WEP, WPA or WPA2-TKIP
encryption this device may operate in legacy wireless mode (802.11b/g). You may not get
802.11n performance as these forms of encryption are not supported by the 802.11n
specification.
Avoid stacking hardware on top of each other to prevent overheating issues
Maintain enough free space around the hardware for good ventilation and airflow. There
should also be plenty of free space around the antennas to allow the wireless signal to
propagate. Please also make sure that the wireless hardware is not placed in any type of
shelving or enclosures.
There are a number of other environmental factors that can impact the range of wireless
devices.
1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at
an angle. The more material the signal has to pass through the more signal you will lose.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of
a wireless device. Position the wireless devices in a manner that will minimize the amount
of obstructions between them.
3. Building materials can have a large impact on your wireless signal. In an indoor
environment, try to position the wireless devices so that the signal passes through less
dense material such as dry wall. Dense materials like metal, solid wood, glass or even
furniture may block or degrade the signal.
4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless
adapter's site survey tool to determine the best antenna orientation for your wireless
devices.
5. Interference from devices that produce RF (radio frequency) noise can also impact your
signal. Position your wireless devices away from anything that generates RF noise, such
as microwaves, HAM radios, Walkie-Talkies and baby monitors.
6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as
2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency
can potentially drop the wireless signal. Although the phone may not be in use, the base
can still transmit wireless signals. Move the phone's base station as far away as possible
from your wireless devices.
If you are still experiencing low or no signal consider repositioning the wireless devices or installing
additional access points. The use of higher gain antennas may also provide the necessary
coverage depending on the environment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
GPL/LGPL General Information
This TRENDnet product includes free software written by third party developers. These codes are subject to the GNU
General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). These codes are distributed WITHOUT
WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these
codes. The details of the GNU GPL and LGPL are included in the product CD-ROM. Please also go to
at least three years from the product shipping date. You could also request the source codes by contacting TRENDnet.
20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511.
Informations générales GPL/LGPL
Ce produit TRENDnet comprend un logiciel libre écrit par des programmeurs tiers. Ces codes sont sujet à la GNU
General Public License ("GPL" Licence publique générale GNU) ou à la GNU Lesser General Public License ("LGPL"
Licence publique générale limitée GNU). Ces codes sont distribués SANS GARANTIE et sont sujets aux droits d'auteurs
des programmeurs. TRENDnet ne fournit pas d'assistance technique pour ces codes. Les détails concernant les GPL et
LGPL GNU sont repris sur le CD-ROM du produit. Veuillez également vous rendre en (http://www.gnu.org/licenses/gpl.txt)
disponibles au téléchargement sur le site Internet de TRENDnet web site (http://trendnet.com/downloads/list_gpl.asp)
durant au moins 3 ans à partir de la date d'expédition du produit. Vous pouvez également demander les codes source en
contactant TRENDnet. 20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511
Allgemeine Informationen zu GPL/LGPL
freie Software „Linux „mtd“ (Memory Technology Devices) Implementation (© 2000 David Woodhouse), erstmals integriert
test3.tar.bz2), sowie weitere freie Software. Sie haben durch den Erwerb dieses Produktes keinerlei
Gewährleistungsansprüche gegen die Berechtigten an der oben genannten Software erworben; weil diese die Software
kostenfrei lizenzieren gewähren sie keine Haftung gemäß unten abgedruckten Lizenzbedingungen. Die Software darf von
jedermann im Quell-und Objektcode unter Beachtung der Lizenzbedingungen der GNU General Public License Version 2,
und GNU Lesser General Public License (LGPL) vervielfältigt, verbreitet und verarbeitet werden. Die Lizenz ist unten im
englischsprachigen Originalwortlaut wiedergegeben. Eine nichtoffizielle Übersetzung in die deutsche Sprache finden Sie
auch auf der mitgelieferten CD-ROM. Sie können Quell-und Objektcode der Software für mindestens drei Jahre auf
downloadend. Sofern Sie nicht über die Möglichkeit des Downloads verfügen können Sie bei TRENDnet. 20675
Manhattan Place, Torrance, CA 90501 -U.S.A -, Tel.: +1-310-961-5500, Fax: +1-310-961-5511 die Software anfordern.
Información general sobre la GPL/LGPL
Este producto de TRENDnet incluye un programa gratuito desarrollado por terceros. Estos códigos están sujetos a la
Licencia pública general de GNU (“GPL”) o la Licencia pública general limitada de GNU (“LGPL”). Estos códigos son
distribuidos SIN GARANTÍA y están sujetos a las leyes de propiedad intelectual de sus desarrolladores. TRENDnet no
ofrece servicio técnico para estos códigos. Los detalles sobre las licencias GPL y LGPL de GNU se incluyen en el CD-
para ver las cláusulas específicas de cada licencia. Los códigos fuentes están disponibles para ser descargados del sitio
envío del producto. También puede solicitar el código fuente llamando a TRENDnet. 20675 Manhattan Place, Torrance,
CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511
Îáùàÿ èíôîðìàöèÿ î ëèöåíçèÿõ GPL/LGPL
 ñîñòàâ äàííîãî ïðîäóêòà TRENDnet âõîäèò áåñïëàòíîå ïðîãðàììíîå îáåñïå÷åíèå, íàïèñàííîå ñòîðîííèìè
ðàçðàáîò÷èêàìè. Ýòî ÏÎ ðàñïðîñòðàíÿåòñÿ íà óñëîâèÿõ ëèöåíçèé GNU General Public License ("GPL") èëè GNU
Lesser General Public License ("LGPL"). Ïðîãðàììû ðàñïðîñòðàíÿþòñÿ ÁÅÇ ÃÀÐÀÍÒÈÈ è îõðàíÿþòñÿ àâòîðñêèìè
ïðàâàìè ðàçðàáîò÷èêîâ. TRENDnet íå îêàçûâàåò òåõíè÷åñêóþ ïîääåðæêó ýòîãî ïðîãðàììíîãî îáåñïå÷åíèÿ.
Ïîäðîáíîå îïèñàíèå ëèöåíçèé GNU GPL è LGPL ìîæíî íàéòè íà êîìïàêò-äèñêå, ïðèëàãàåìîì ê ïðîäóêòó.
 ïóíêòàõ (http://www.gnu.org/licenses/gpl.txt) è (http://www.gnu.org/licenses/lgpl.txt) èçëîæåíû êîíêðåòíûå óñëîâèÿ
êàæäîé èç ëèöåíçèé. Èñõîäíûé êîä ïðîãðàìì äîñòóïåí äëÿ çàãðóçêè ñ âåá-ñàéòà TRENDnet
(http://trendnet.com/downloads/list_gpl.asp) â òå÷åíèå, êàê ìèíèìóì, òðåõ ëåò ñî äíÿ ïîñòàâêè ïðîäóêòà.
Êðîìå òîãî, èñõîäíûé êîä ìîæíî çàïðîñèòü ïî àäðåñó TRENDnet. 20675 Manhattan Place, Torrance, CA 90501, USA.
Tel: +1-310-961-5500 Fax: +1-310-961-5511
Download from Www.Somanuals.com. All Manuals Search And Download.
GPL/LGPL informações Gerais
Este produto TRENDnet inclui software gratuito desenvolvido por terceiros. Estes códigos estão sujeitos ao GPL (GNU
General Public License) ou ao LGPL (GNU Lesser General Public License). Estes códigos são distribuídos SEM
GARANTIA e estão sujeitos aos direitos autorais dos desenvolvedores. TRENDnet não presta suporte técnico a estes
códigos. Os detalhes do GNU GPL e do LGPL estão no CD-ROM do produto. Favor acessar
códigos fonte estão disponíveis para download no site da TRENDnet (http://trendnet.com/langen/downloads/list_gpl.asp)
por pelo menos três anos da data de embarque do produto. Você também pode solicitar os códigos fonte contactando
TRENDnet, 20675 Manhattan Place, Torrance, CA 90501, USA.Tel: +1-310-961-5500, Fax: +1-310-961-5511.
GPL/LGPL üldinformatsioon
See TRENDneti toode sisaldab vaba tarkvara, mis on kirjutatud kolmanda osapoole poolt. Koodid on allutatud GNU
(General Public License) Üldise Avaliku Litsentsi (GPL) või GNU (Lesser General Public License) ("LGPL") Vähem Üldine
Avalik Litsentsiga. Koode vahendatakse ILMA GARANTIITA ja need on allutatud arendajate poolt. TRENDnet ei anna
koodidele tehnilist tuge. Detailsemat infot GNU GPL ja LGPL kohta leiate toote CD-ROMil. Infot mõlema litsentsi
Samuti võite lähtekoodi paluda TRENDneti'lt, 20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500,
Fax: +1-310-961-5511.
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Warranty Registration
Please take a moment to register your product online.
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright ©2009. All Rights Reserved. TRENDnet.
|