OWNER’S
MANUAL
COLOR TV/VCR/DVD TRIPLE COMBO
(19 inch)
6719DES
SKIP
PLAY
SKIP
STOP
OPEN/CLOSE
SELECT
CHANNEL
REC/OTR
REW
PLAY
F.FWD
STOP/EJECT
POWER
VOLUME
HEADPHONE VIDEO
L
-
AUDIO
-
R
DVD
TV/VCR
SEARCH
SUPPLIED ACCESSORIES
ACCESSORIES
PART NO.
Remote Control Unit NE222UD
Batteries
2 AA Batteries
1EMN20035
Owner’s Manual
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an ENERGY STAR®
Partner, our company has
determined that this product meets
the ENERGY STAR® guidelines for
energy efficiency. ENERGY STAR®
is a U.S. registered mark.
If you need additional operating assistance after reading this owner’s
manual or to order replacement accessories, please call
TOLL FREE : 1-800-968-3429.
Please read before using this equipment
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD I N
WI RE
GROUND
CL AMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRI C
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/VCR/DVD, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
19.Damage Requiring Service-Unplug this TV/VCR/DVD
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/VCR/DVD.
c. If the TV/VCR/DVD has been exposed to rain or water.
d. If the TV/VCR/DVD does not operate normally by follow-
ing the operating instructions. Adjust only those controls
that are covered by the operating instructions, as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the TV/VCR/DVD to its normal operation.
14.Lightning-For added protection for this TV/VCR/DVD
receiver during a lightning storm, or when it is left unat-
tended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV/VCR/DVD due to
lightning and power-line surges.
e. If the TV/VCR/DVD has been dropped or damaged in any
way.
f. When the TV/VCR/DVD exhibits a distinct change in per-
formance-this indicates a need for service.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
16.Overloading-Do not overload wall outlets and extension
21.Safety Check-Upon completion of any service or repairs to
this TV/VCR/DVD, ask the service technician to perform
routine safety checks to determine that the TV/VCR/DVD
is in proper operating condition.
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/VCR/DVD through openings as they may
touch dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the TV/VCR/DVD.
22.Heat-This TV/VCR/DVD product should be situated away
from heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this TV/VCR/DVD
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
- 3 -
EN
1B15
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
IMPORTANT COPYRIGHT INFORMATION
LASER SAFETY
Unauthorized copying, broadcasting, public perfor-
mance and lending of discs are prohibited.
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to ser-
vice this device, due to possible eye injury.
This product incorporates copyright protection tech-
nology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing
uses only unless otherwise authorized by
CAUTION: USE OF CONTROLS OR ADJUST-
MENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est con-
forme à la norme NMB-003 du Canada.
RADIO-TV INTERFERENCE
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
- 4 -
EN
1B15
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
LOCATION
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a TV/VCR/
DVD which has moisture, it may damage the DVD
and TV/VCR/DVD. Therefore when the condensation
occurs inside the unit, turn the POWER on and allow
at least 2 hours for the unit to dry out.
For safe operation and satisfactory performance of
your TV/VCR/DVD, keep the following in mind
when selecting a place for its installation:
Shield it from direct sunlight and keep it away from
sources of intense heat.
•
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top or bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
•
•
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some head-
ings and notes in this manual, with the following
meanings
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
Do not place the TV/VCR/DVD near strong magnetic
fields.
•
•
•
TV/VCR
: Description refers to TV/VCR operation (in the
TV/VCR mode).
Avoid moving TV/VCR/DVD to locations where
temperature differences are extreme.
•
DVD-V
: Description refers to playback of DVD video discs
(in the DVD mode).
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
CD
: Description refers to playback of audio CDs
(in the DVD mode).
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
•
•
MP3
: Description refers to playback of MP3 discs
(in the DVD mode).
If by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/VCR/DVD disc loading tray.
•
QUICK
•
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
Do not place anything directly on top of the unit.
•
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-
tions concerning chemical wastes.
The serial number of this product may be found on the back of the unit. No other TV/VCR/DVD has the same
serial number as yours. You should record the number and other vital information here and retain this book as
a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
- 5 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
STILL PICTURE . . . . . . . . . . . . . .26
TIME SEARCH . . . . . . . . . . . . . . .39
MARKER SETUP SCREEN . . . . . .39
C IMPORTANT SAFEGUARDS . . . . .2
VERTICAL HOLD CONTROL . . .26
C PRECAUTIONS . . . . . . . . . . . . . . . .4
C SPECIAL PLAYBACK . . . . . . . . . .27
RENTAL PLAYBACK . . . . . . . . . .27
AUTO REPEAT PLAYBACK . . . . .27
C
SPECIAL PLAYBACK FUNCTION . . .40
REPEAT . . . . . . . . . . . . . . . . . . . . .40
PROGRAM . . . . . . . . . . . . . . . . . . .40
RANDOM PLAYBACK . . . . . . . . .40
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
C SEARCH . . . . . . . . . . . . . . . . . . . . .28
ZERO RETURN . . . . . . . . . . . . . . .28
PICTURE SEARCH . . . . . . . . . . . .28
TIME SEARCH . . . . . . . . . . . . . . .28
INDEX SEARCH . . . . . . . . . . . . . .29
SYMBOLS USED IN THIS
MANUAL . . . . . . . . . . . . . . . . . . . . .5
C PLAYING A MP3 DISC . . . . . . . . . .41
MP3 PLAYBACK . . . . . . . . . . . . . .41
REPEAT . . . . . . . . . . . . . . . . . . . . .41
PROGRAM . . . . . . . . . . . . . . . . . . .41
RANDOM PLAYBACK . . . . . . . . .41
C TABLE OF CONTENTS . . . . . . . . . .6
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . . . . .9
C SPECIAL FEATURES . . . . . . . . . .29
REAL TIME TAPE COUNTER . . .29
AUTO REWIND-EJECT . . . . . . . .29
C CHANGING THE SETTINGS . . . .42
SUBTITLE LANGUAGE . . . . . . . .42
AUDIO LANGUAGE . . . . . . . . . . .42
STEREO SOUND MODE . . . . . . . .42
CAMERA ANGLE . . . . . . . . . . . . .42
BLACK LEVEL SETTING . . . . . . .42
VIRTUAL SURROUND . . . . . . . . .42
C PREPARATION FOR USE . . . . . . .11
ANTENNA/CABLE
CONNECTION . . . . . . . . . . . . . . . .11
C RECORDING . . . . . . . . . . . . . . . . .30
NORMAL RECORDING . . . . . . . .30
CONNECTING TO EXTERNAL
INPUT JACKS . . . . . . . . . . . . . . . .12
SKIPPING UNWANTED SCENES
DURING RECORDING . . . . . . . . .30
INSTALLING THE BATTERIES . .12
EXTERNAL INPUT MODE . . . . . .12
OTR (One Touch Recording) . . . . . .31
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .31
C
THE ON-SCREEN INFORMATION . . .43
CONNECTING TO A STEREO
AMPLIFIER EQUIPPED WITH DIGI-
TAL INPUT JACKS SUCH AS MD
DECK OR DAT DECK (for DVD) .13
C CHANGING THE DVD SETUP
C TIMER . . . . . . . . . . . . . . . . . . . . . .32
ITEMS . . . . . . . . . . . . . . . . . . . . . . .44
AUTOMATIC
TIMER RECORDING . . . . . . . . . .32
LANGUAGE SETTING . . . . . . . . .44
DISPLAY SETTING . . . . . . . . . . . .45
AUDIO SETTINGS . . . . . . . . . . . .45
PARENTAL CONTROL . . . . . . . . .46
INITIALIZE . . . . . . . . . . . . . . . . . .46
CONNECTING TO A DOLBY
DIGITAL DECODER (for DVD) . .14
TIMER PROGRAM EXTENSION .33
TV/VCR SECTION
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . .34
C SET UP FOR USE . . . . . . . . . . . . .15
AUTO RETURN . . . . . . . . . . . . . . .34
SLEEP TIMER . . . . . . . . . . . . . . . .34
SELECTING THE LANGUAGE . .15
C TROUBLESHOOTING GUIDE . . .47
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . . . . .15
C ON SCREEN DISPLAY . . . . . . . . .35
C MAINTENANCE . . . . . . . . . . . . . . .50
DAYLIGHT-SAVING TIME . . . . . .17
CHANNEL SET UP . . . . . . . . . . . .18
DISC HANDLING . . . . . . . . . . . . .50
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .35
C SPECIFICATIONS . . . . . . . . . . . . .51
C ESPAÑOL . . . . . . . . . . . . . . . . . . . .52
C WARRANTY . . . . . . . . . . .Back Cover
DELETING (OR ADDING)
CHANNEL(S) . . . . . . . . . . . . . . . . .18
DVD SECTION
C TV OPERATION . . . . . . . . . . . . . . .19
WATCHING A TV PROGRAM . . .19
DEGAUSSING . . . . . . . . . . . . . . . .19
PICTURE CONTROL . . . . . . . . . . .19
CLOSED CAPTION SYSTEM . . . .20
V-CHIP SET UP . . . . . . . . . . . . . . .21
C ABOUT THE DISCS . . . . . . . . . . . .36
PLAYABLE DISCS . . . . . . . . . . . .36
DISC TYPES . . . . . . . . . . . . . . . . .36
C PLAYING A DISC . . . . . . . . . . . . . .37
BASIC PLAYBACK . . . . . . . . . . . .37
GENERAL FEATURES . . . . . . . . .37
DISC MENU . . . . . . . . . . . . . . . . .37
TITLE MENU . . . . . . . . . . . . . . . . .37
RESUME . . . . . . . . . . . . . . . . . . . .38
PAUSE . . . . . . . . . . . . . . . . . . . . . .38
STEP BY STEP PLAYBACK . . . . .38
C MTS(Multi-Channel Television
sound)SYSTEM . . . . . . . . . . . . . . . .23
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .23
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .23
SELECTING THE MTS SYSTEM .24
FAST FORWARD/REVERSE
SEARCH . . . . . . . . . . . . . . . . . . . .38
C VIDEO CASSETTE . . . . . . . . . . . . .25
SLOW FORWARD / SLOW
REVERSE . . . . . . . . . . . . . . . . . . . .38
C PLAYBACK . . . . . . . . . . . . . . . . . . .26
NORMAL PLAYBACK . . . . . . . . .26
TRACKING ADJUSTMENT . . . . .26
SLOW MOTION . . . . . . . . . . . . . .26
C SEARCH FUNCTION . . . . . . . . . . .39
TRACK SEARCH . . . . . . . . . . . . .39
TITLE / CHAPTER SEARCH . . . .39
- 6 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
TV/VCR Mode
Hi-Fi system–The Hi-Fi stereo recording system
offers you excellent sound quality with a dynamic
range of 80dB, frequency response from 20Hz to
20kHz and 0.005% wow and flutter.
Rotary 4-head Record/Playback System–Four heads
ensure excellent picture quality and special effects playback.
Index Search–Fast-forwards to start of next recording.
Slow Motion–View recorded program at slower
than normal speed.
Infrared remote control
Trilingual on screen TV/VCR setup display
selectable in English or Spanish or French
Real time counter–This shows the elapsed recording
or playback time in hours, minutes and seconds. The
“–” indication will appear when the tape is rewound
further than the tape counter position “0:00:00”.
181 channel capability PLL frequency synthesiz-
er tuner with direct station call–(A converter may
be necessary to view scrambled cable channels.)
Auto Clock Setting–Allows you to set the clock
function from a PBS broadcast station.
Closed caption system–You may view specially
labeled (cc) TV programs, movies, news, prere-
corded tapes, etc. with either a dialogue caption or
text display added to the program.
Auto power on and off system–Automatically
turns on the TV/VCR/DVD when you insert the
cassette, turns off after auto-rewind and ejects
when the beginning of the tape is reached.
Auto rewind when the end of a tape is
reached–This function doesn’t occur when using
timer recording.
2 Step picture search operation–You can view a
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
Three different playback tape speeds : SP/LP/SLP
Two different recording tape speeds : SP/SLP
Auto Head Cleaner–Automatically cleans video
heads as you insert or remove a cassette.
Zero Return–The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
Still–“Freeze” the picture at any time, for close
viewing of a particular scene.
Digital Auto Tracking (DTR)–Automatically
adjusts the tracking for each tape you play.
Rental play mode–Improves playback picture
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
Time search–Lets you set the TV/VCR/DVD to
advance the tape by entering the desired playback
time you want to skip.
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible at the
push of the REC/OTR button.
1 Year, 8 events (including Daily and Weekly
Timer Recording)–The built-in timer allows you to
record up to 8 programs at different times on dif-
ferent channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broad-
casts and the Weekly timer allows recording to be
made once a week up to the end of the tape.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Auto return–After timer recording is finished, the
TV/VCR/DVD can return to the beginning of the
recording.
•
Smooth mode change–TV/VCR mode DVD
mode automatically changes without control.
Sleep timer–Allows you to have the TV/VCR/DVD
automatically turn off at a desired time.
Timer Program Extension–Allows you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
•
•
•
- 7 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Mode
¡Playback MP3 disc
¡Dolby Digital sound
¡On-screen display
This TV/VCR/DVD can handle Dolby Digital sur-
round sound having 5.1 channels when connected to
a Dolby Digital decoder.
Information about the current operation can be dis-
played on a TV screen, allowing you to confirm the
currently active functions (such as program play-
back), on the TV screen using the remote control.
¡Still/fast/slow/step playback
Various playback modes are available including still
pictures, fast forward/reverse, slow motion and step
frames.
¡Search
Chapter search / Title search / Track search / Time
search
¡Random playback for audio CD and MP3
This TV/VCR/DVD can shuffle the order of tracks
to play them in random order.
¡Repeat
Chapter / Title / Track / Group / All / A-B
¡Program playback for audio CD and MP3
You can program the order of tracks to play them in
any desired order.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which
the play was stopped.
¡Virtual Surround
¡Bit rate indication
¡DVD menus in a desired language
You can display DVD menus in a desired language,
if available on a DVD.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no
input from the TV/VCR/DVD for five minutes in the
stop mode. When the screen saver program is acti-
vated for 15 minutes, the power automatically turns
off.
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Subtitles in a desired language
You can select a desired language for the display
subtitles, if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc
contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available
on a disc.
¡Parental lock
You can set the control level to limit playback of
discs which may not be suitable for children.
¡Automatic detection of discs
This TV/VCR/DVD automatically detects if the
loaded disc is DVD, audio CD or MP3 on disc.
NOTE:
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
•
If you decide to use a universal remote control with this TV/VCR/DVD, please be aware that the code num-
ber given may not operate this TV/VCR/DVD. In this case, please call the manufacturer of the universal
remote control.
- 8 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING CONTROLS AND FUNCTIONS
- TV/VCR/DVD FRONT PANEL - [Fig.1]
DVD buttons
TV/VCR buttons
SKIP
PLAY
SKIP
STOP
OPEN/CLOSE
SELECT
CHANNEL
REC/OTR
REW
PLAY
F.FWD
STOP/EJECT
POWER
VOLUME
HEADPHONE VIDEO
L
-
AUDIO
-
R
DVD
TV/VCR
SEARCH
1
2
3 4
3
5
6
7
8 9 10 11 12 13 14 4 15 16 17 18 19 20 21
5.STOP Button [TV/VCR P.26 / DVD P.37]
Stops operation of the disc. (or front panel)
Stops operation of the disc or tape contents.
(remote control)
[Fig. 2]
- REMOTE CONTROL -
6.OPEN/CLOSE Button [DVD P.37]
Press to insert discs into or remove them from the
tray.
7.Disc loading tray
8.DVD Indicator
Lights on during DVD mode.
POWER PICTURE SLEEP SELECT
1
45
44
22
1
4
2
5
8
0
3
6
CH.
11
23
7
PAUSE
9
+100
9.SELECT Button
VOL.
2
Press to change to TV/VCR mode, external input
mode or DVD mode.
+10
24
25
26
SPEED C.RESET
V.SURR
MUTE
43
42
10.TV/VCR Indicator
Lights on during TV/VCR mode.
PLAY
STOP
3 (DVD)
15 (TV/VCR)
5
41
(DVD) 3
(TV/VCR) 414
11. CHANNEL (CH.) K/L Buttons
Press to select memorized channel.
DISC
MENU
RECORD
12. Recording Indicator
13
Flashes during recording. Lights up in the Stand-
by mode for Timer Recording.
DISPLAY
SETUP
40
ENTER
27
TITLE
RETURN
13. REC/OTR Button (Front Panel) [TV/VCR P.30, 31]
Press to start manual recording. Press repeatedly
to start One Touch Recording.
RECORD Button (Remote Control) [TV/VCR P.30]
Press to start manual recording.
14. REW Button (for TV/VCR) [TV/VCR P.26]
Press to rewind the tape, or to view the picture
rapidly in reverse during playback mode. (Rewind
Search)
39
38
37
28
29
30
CLEAR SEARCH MODE REPEAT
A-B
AUDIO SUBTITLE ANGLE
MODE
31
32
33
36
35
34
15. F.FWD Button (for TV/VCR) [TV/VCR P.26]
Press to rapidly advance the tape, or to view the
picture rapidly in forward during playback mode.
(Forward Search)
1.POWER Button [TV/VCR P.15 / DVD P.37]
Press to turn the power on and off.
16. STOP/EJECT Button [TV/VCR P.28]
2.VOLUME (VOL.) X/Y Buttons
Press to control the volume level for the DVD and TV.
3.SKIP (SEARCH) Buttons (for DVD)[P.38]
Press once to skip chapters or tracks to a desired
point.
Press and hold to change forward or reverse play-
back speed.
Press to stop the tape motion. Press in the Stop
mode to remove tape from the TV/VCR/DVD.
17. Remote sensor window
18. HEADPHONE Jack
To connect headphone (not supplied) for personal
listening.
19. VIDEO input Jack
4.PLAY Button [TV/VCR P.26 / DVD P.37]
Starts playback of the disc or tape contents.
Connect to the video output jack of a video
camera or VCR.
- 9 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
- TV/VCR/DVD REAR PANEL - [Fig.3]
ANT.
AUDIO OUT
COAXIAL
46
47
48
20. AUDIO L/R input Jacks
31. MODE Button [DVD P.41]
Connect to the audio output jacks of a video
camera or VCR.
Activates program playback or random playback mode.
32. SEARCH MODE Button [DVD P.39]
21. Cassette compartment
Press to locate a desired point.
22. PICTURE Button
33. AUDIO Button [DVD P.42]
Press to select a desired audio language or sound
mode.
Press to adjust the picture.
23. Number Buttons
34. SUBTITLE Button [DVD P.42]
TV Mode:[P.15]
Press two digits to directly access the desired
channel.
Remember to press a "0" before a single digit
channel.
+100 Button–
Press to select cable channels which are equal or
greater than number 100.
DVD Mode:
Press to enter the desired number.
+10 Button–
Press to enter the desired numbers which are
equal or greater than number 10.
Press to select a desired subtitle language.
35. REPEAT Button [DVD P.42]
Repeats playback of the current disc, title, chapter
or track.
36. ANGLE Button (DVD mode) [DVD P.42]
Press to change the camera angle to see the
sequence being played back from a different angle.
37. A-B REPEAT Button [DVD P.40]
Repeats playback of a selected section.
38. RETURN Button
Returns to the previous operation in the DVD
setup mode.
24. PAUSE Button [TV/VCR P.26 / DVD P.38]
39. ENTER Button
Pauses the current disc or tape operation.
Press to accept a setting.
25. SPEED Button [TV/VCR P.30]
Press to choose the desired recording speed:
SP/SLP.
26. C.RESET Button [TV/VCR P.28]
Press to reset counter to 0:00:00.
Press to cancel a setting of timer program. (See
page 33.)
40. Arrow Buttons
TV/VCR Mode:
Press to select a setting mode from the menu on
the TV screen.
Press to select or adjust from a particular menu.
DVD Mode:
Use when making settings while watching the
display on a TV screen.
27. DISPLAY Button
TV/VCR Mode:
41. DISC MENU Button [DVD P.37]
Display the counter or the current channel number
and current time on the TV screen.
DVD Mode:[P.43]
Displays the current status on the TV screen for
checking purposes.
Displays the menus in the DVD.
42. V. SURR (VIRTUAL SURROUND) Button [DVD P.42]
Sets virtual surround on/off.
43. MUTE Button
Mutes the sound. Press it again to resume sound.
28. SETUP Button [TV/VCR P.15] [DVD P.44-46]
Press to enter or exit the TV menu or DVD setup
mode.
44. SLEEP Button [TV/VCR P.34]
Sets the Sleep Timer.
45. SELECT Button
29. TITLE Button [DVD P.37]
Press to switch TV/VCR and DVD mode. You can
see the mode (TV/VCR or DVD) on the front
panel indicator.
Displays the title menu.
30. CLEAR Button
Resets a setting.
- 10 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
46. ANT. in Jack
48. COAXIAL digital audio out Jack
Connect to the digital input of an external
amplifier or decoder for DVD audio only.
Connect to an antenna, cable system, or satellite
system.
47. Power cord
Connect to a standard AC outlet (120V/60Hz).
NOTE: Remove the power cord from the hook to
avoid breaking a wire before you connect
to a standard AC outlet.
PREPARATION FOR USE
ANTENNA/CABLE CONNECTION
VHF/UHF Antenna
(Not supplied)
Satellite Box or
Cable Box (Not supplied)
OUT
IN
From Cable System or
Satellite Dish
VHF Antenna (Not supplied)
75-ohm
Coaxial
Cable
UHF Antenna
(Not supplied)
From Cable
System
(Not sup-
plied)
ANT.
A
UDIO OUT
COAXIAL
AUDIO OUT
COAXIAL
or
or
VHF/UHF
Combiner
(Not supplied)
ANT.
75-ohm Coaxial
Cable (Not
supplied)
or
[Fig. 4]
Flat twin-lead cable
VHF/UHF SEPARATE ANTENNAS
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
In some areas it will be necessary to use an outdoor
antenna.
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown in the illustration.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
By using this connection you can also record scram-
bled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/VCR/DVD Remote Control. Unattended timer
recording is limited to one channel at a time.
Use this connection if your cable system connects
directly to your TV/VCR/DVD without a converter
box.
By using this connection you can:
1) Use the TV/VCR/DVD remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
Antenna/Cable Connections
Continued on the Next Page.
NOTE: This TV/VCR/DVD will ONLY record and
view the same channel.
- 11 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
TO RECORD A SCRAMBLED/UNSCRAM-
BLED CHANNEL
INSTALLING THE BATTERIES
1. Set the TV/VCR/DVD channel selector to the out-
put channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
Note to CATV system installer:
3)Replace the cover.
This reminder is provided to call the CATV sys-
tem installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper ground-
ing and in particular, specifies that the cable
ground shall be connected to the grounding sys-
tem of the building as close to the point of cable
entry as practical.
EXTERNAL INPUT MODE
When using an external input signal (another VCR or
video camera), connect the player’s audio/video out-
put cables to the AUDIO L/R IN/
CONNECTING TO EXTERNAL
INPUT JACKS
When you watch a program recorded on an another
source (VCR or video camera), use the audio/video
input jacks on the front of the TV/VCR/DVD.
Connect the audio/video output jacks of another
source to the AUDIO L/R and VIDEO jacks of this
TV/VCR/DVD.
AUX
VIDEO IN jacks of your
TV/VCR/DVD. Then press the
CHANNEL button K or L until
“AUX” appears on the screen.
Then press the CHANNEL button K or L until
"AUX" appears on the screen.
NOTE:
When you connect a monaural VCR (another
•
source) to this TV/VCR/DVD, connect the Audio
output jack of the monaural VCR (another source)
to the AUDIO L jack of this TV/VCR/DVD. The
audio will output in both L and R channel equally.
To the audio
output jacks
[Another source]
HEADPHONE
VIDEO
L-AUDIO-R
Audio/Video
coaxial cable
(not supplied)
etc.
To the video
[Front of the
TV/VCR/DVD]
output jack
[Fig. 5]
- 12 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGI-
TAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)
Use an audio coaxial digital cable available at retail for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
ANT.
AUDIO OUT
COAXIAL
Amplifier equipped with digital
To DIGITAL AUDIO OUT
input jacks, MD deck,
(PCM/BITSTREAM)
DAT deck, etc.
COAXIAL jack
(only DVD AUDIO OUT)
To COAXIAL DIGITAL
AUDIO INPUT jack
[Fig. 6]
NOTES:
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
•
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for the components to be connected to the TV/VCR/DVD.
Set Dolby Digital to OFF for audio output in the setup mode. Playing a TV/VCR/DVD using incorrect set-
tings may generate noise distortion and may also damage the speakers.
•
•
•
- 13 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this TV/VCR/DVD to play a DVD disc in a 5.1 channel Dolby Digital surround format, the
TV/VCR/DVD outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hook-
ing the TV/VCR/DVD up to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience
with powerful and high-quality surround sound as enjoyed in movie theaters.
Use audio coaxial digital cables available at retail for the audio connections.
Center
speaker
ANT.
AUDIO OUT
COAXIAL
Front speaker
(left)
Front speaker
(right)
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
Dolby Digital
decoder
To COAXIAL DIGITAL
AUDIO INPUT jack
Subwoofer
Surround
speaker
(left)
Surround
speaker
(right)
[Fig. 7]
NOTES:
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for the components to be connected to the TV/VCR/DVD.
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.
(See page 45 to set DOLBY DIGITAL to ON.)
•
•
•
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup
mode. Playing a TV/VCR/DVD using incorrect settings may generate noise distortion and may also damage
the speakers.
•
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
- 14 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
TV/VCR SECTION
SET UP FOR USE
SELECTING THE LANGUAGE
CLOCK SET UP
(AUTO / MANUAL)
TV/VCR
TV/VCR
1 Plug in the TV/VCR/DVD power cord
Plug the TV/VCR/DVD power cord into a
standard AC outlet.
The TV/VCR/DVD clock must be set correctly before
VCR timer recording is possible. It is suggested that
the clock be set manually when first setting up the
TV/VCR/DVD, then set to [ON] the auto clock set-
ting which will periodically correct the setting if nec-
essary.
NOTE: If you cannot receive a station with time
signals, auto clock setting cannot be performed. Use
manual setting only.
NOTE:
If any digits appear in the corner of the
screen, press the POWER button without unplug-
ging the power cord.
•
Make sure ...
Press the SELECT button to select TV/VCR mode or
make sure TV/VCR lights on.
•
MANUAL CLOCK SETTING
Press the POWER button to turn on the TV/VCR/DVD.
NOTE: This function effects only the language on
the screen menu and not the audio source.
•
Make sure ...
The TV/VCR/DVD is turned on.
•
In the example below, the clock is to be set to:
2 Select “LANGUAGE”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “LANGUAGE”.
– M E N U –
DATE
May 6th, 2004
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
SETTING TIME 5:40PM
B
1 Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
ZERO RETURN
TIME SEARCH
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B
V-CHIP SET UP
3 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”
Select “ENGLISH”, “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using the ENTER button.
Press the Arrow button K or L to
point to “SETTING CLOCK”.
Then press the ENTER button.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
2 Select “MANUAL CLOCK SET”
Press the Arrow button K or L to
point to “MANUAL CLOCK
SET”.
4 Exit the Language mode
– SETTING CLOCK –
Press the SETUP button on the remote control to
return to TV mode.
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
B
NOTE: If for some reason the menu is in Spanish or
French, press the SETUP button on the remote control,
press the Arrow button K or L to point to “IDIOMA
[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then
press the ENTER button, then press the SETUP button
on the remote control.
[OFF]
Then press the ENTER button.
3 Select the month
Press the Arrow button K or
– MANUAL CLOCK SET –
MONTH DAY YEAR
L
until your desired month appears.
0 5
/
– – – – – – – – –
(Example: May → 05)
HOUR
– –
MINUTE
– – – –
Then press the Arrow button B.
(Or press the Arrow button { to
go back one step.)
:
4 Select the day
– MANUAL CLOCK SET –
MONTH DAY YEAR
Press the Arrow button K or
L
until your desired day appears.
0 5
/
0 6 – – – – – – –
(Example: 6th → 06)
Then press the Arrow button B.
HOUR
– –
MINUTE
– – – –
:
- 15 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC CLOCK SETTING
Make sure ...
5 Select the year
– MANUAL CLOCK SET –
MONTH DAY YEAR
The TV/VCR/DVD is turned on.
Confirm the TV/VCR/DVD is receiving a RF
•
•
Press the Arrow button K or
L
0 5
/
0 6 THU 2 0 0 4
until your desired year appears.
(Example: 2004)
Then press the Arrow button B.
(Radio Frequency) signal from either an antenna or
cable system connection using the ANT. terminal
on the rear of the TV/VCR/DVD.
NOTE:
HOUR
– –
MINUTE
– – – –
:
If a cable converter box is being used, make sure it
is powered on.
You must use the TV/VCR/DVD remote control to
perform the clock setting procedure.
6 Select the hour
– MANUAL CLOCK SET –
MONTH DAY YEAR
•
Press the Arrow button K or
L
0 5
/
0 6 THU 2 0 0 4
until your desired hour appears.
(Example: 5, PM)
Then press the Arrow button B.
•
HOUR
0 5
MINUTE
– – PM
:
If the TV/VCR/DVD is connected directly to a
•
cable converter box or satellite box, the local PBS
station must be selected on the cable box itself and
the TV/VCR/DVD must be set to the output chan-
nel of the cable converter box or satellite box (usu-
ally channel 3 or 4), to be able to set up or correct
the clock automatically.
– MANUAL CLOCK SET –
MONTH DAY YEAR
7 Select the minute
Press the Arrow button K or
until the desired minute appears.
(Example: 40)
L
0 5
/
0 6 THU 2 0 0 4
HOUR
0 5
MINUTE
4 0 PM
:
1 Select “SETTING CLOCK”
– M E N U –
8 Start the clock
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the SETUP button on the
5:40 PM
B
Press the SETUP button on the
remote control.
remote control.
Press the Arrow button K or L to
select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Although seconds are not displayed,
they begin counting from 00 when
you press the SETUP button on the
remote control. Use this feature to synchronize the
clock with the correct time.
TIME SEARCH
2 Set “AUTO CLOCK” to [ON]
Press the Arrow button B until
“AUTO CLOCK [ON]” appears.
– SETTING CLOCK –
NOTE:
B
AUTO CLOCK
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ON]
When unplugging the AC cord or if there is a power
failure for more than 3 seconds, you may have to
reset the clock.
[ 02 ]
[OFF]
TO CHANGE CLOCK SETTING
If you want to change the clock,
1) Follow steps [1] and [2].
2) Select where you want to change using the Arrow
button B.
3) Enter correct numbers using the Arrow button
3 Begin “AUTO CLOCK CH SEARCH”
Press the Arrow button K or L to
– SETTING CLOCK –
select “AUTO CLOCK CH
SEARCH”.
AUTO CLOCK
[ON]
B
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
[OFF]
Press the ENTER button.
The TV/VCR/DVD is now
searching for the station which contain the auto
clock set signal. The search for a signal may take
up to 20 seconds per channel.
K
•
or L.
4) Press the SETUP button on the remote control to
start the clock.
– AUTO CLOCK CH SEARCH –
“_ _” appears at the lower left of
the screen when the search has
ended.
Auto Clock station- write down
the number(s) that appear on the
screen. These are the auto clock
•
•
PLEASE NOTE:
08
10
13
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and
press the ENTER button to turn [OFF] this function.
Then you can manually adjust the clock.
_ _
station(s) in your area. See step [4] on page 17.
If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 15.
•
Press the SETUP button to exit the screen.
- 16 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: During Auto Clock CH Search, the picture
may be distorted, this is normal.
DAYLIGHT-SAVING TIME
TV/VCR
4 Enter the channel number that contains the
Automatic Clock Setting Signal
Press the SETUP button on the remote control.
Select this feature and the TV/VCR/DVD’s clock
automatically will advance one hour in April, then
reverse one hour in October.
Press the Arrow button K or L to
select “SETTING CLOCK”.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B
Press the ENTER button to enter
“SETTING CLOCK” menu.
Press the Arrow button K or L to
select “AUTO CLOCK CH”.
Press the ENTER button or the
Arrow button { or B until you
locate Auto Clock Set station num-
ber. See step [3] on page 16.
Press the SETUP button to exit the
screen.
First Sunday of April : At 2 AM the clock imme-
•
diately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
– SETTING CLOCK –
Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
•
AUTO CLOCK
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ON]
B
[
45]
Make sure ...
[OFF]
Press the POWER button to turn on the TV/VCR/DVD.
•
1 Select “SETTING CLOCK”
– M E N U –
Press the SETUP button on the
TIMER PROGRAMMING
PICTURE CONTROL
5 Turn off the TV/VCR/DVD
Once the TV/VCR/DVD is turned off , it will period-
ically check and set the correct date and time.
remote control.
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the Arrow button K or L to
point to “SETTING CLOCK”.
Then press the ENTER button.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
2 Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press the Arrow button K or L to
– SETTING CLOCK –
point to “D.S.T.”.
Then press the ENTER button until
[ON] appears.
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
B
[ON]
3 Exit the Daylight-Saving Time mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the
ENTER button.
- 17 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
DELETING (OR ADDING)
CHANNEL(S)
CHANNEL SET UP
TV/VCR
TV/VCR
You can program the tuner to scan all the channels
you receive in your area.
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
NOTE: Channel memory programming is NOT
needed when connected to a cable box or satellite
box. Just select the TV/VCR/DVD channel selector
to the output channel of the cable box or satellite box
(Ex CH3), then select the channel to be viewed on
the Cable Box or Satellite Box.
1 Select “CHANNEL SET UP”
– M E N U –
Press the SETUP button on the
TIMER PROGRAMMING
PICTURE CONTROL
remote control.
SETTING CLOCK
B
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the Arrow button K or L to
point to “CHANNEL SET UP”.
Then press the ENTER button.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Make sure ...
Press the POWER button to turn on the TV/VCR/DVD.
TIME SEARCH
•
1 Select “CHANNEL SET UP”
2 Select “ADD/DELETE CH”
Press the Arrow button K or L to
point to “ADD/DELETE CH”.
Press the ENTER button.
– CHANNEL SET UP –
– M E N U –
Press the SETUP button on the
B
ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
TIMER PROGRAMMING
PICTURE CONTROL
remote control.
SETTING CLOCK
B
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the Arrow button K or L to
point to “CHANNEL SET UP”.
Then press the ENTER button.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
3 Enter the desired channel number
Press the Arrow button K or
until your desired channel number
appears. (You can also use the
number buttons or the CHANNEL
button K or L to enter it)
2 Begin auto ch programming
Press the Arrow button K or L to
point to “AUTO CH PROGRAM-
MING”.
Then press the ENTER button.
The tuner scans and memorizes all
the active channels in your area.
L
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
08
B
ADD / DELETE
(Example: CH8)
You must precede single-digit channel numbers
with a zero (Example: 02 ... 09).
•
When selecting cable channels which are higher
than 99, press the +100 button first, then press the
last two digits. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
3 After scanning
•
The tuner stops on the lowest memorized channel.
•
When AUTO CH PROGRAMMING is activated
where there is no TV signal input, “NO TV SIG-
NALS” will appear on the display after the com-
pletion of the channel scanning.
4 Delete (or add) it from (into) memory
Press the ENTER button. The channel number
changes to light red. The channel is deleted from
memory.
To delete another channel, repeat steps [3] and [4].
If you press the ENTER button again, the channel
The TV/VCR/DVD may recognize TV channels to
•
be CATV channels by the receiving conditions. In
this case, try auto ch programming again in the fine
receiving conditions.
•
•
is memorized again.
Added channel: Light blue.
Deleted channel: Light red.
5 Exit the channel setup mode
Press the SETUP button on the remote control to
return to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL button K or L.
- 18 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
TV OPERATION
WATCHING A TV PROGRAM
PICTURE CONTROL
TV/VCR
TV/VCR
The TV/VCR/DVD’s picture controls – BRIGHT,
CONTRAST, COLOR, TINT and SHARPNESS –
are preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a more natural looking image.
1 Turn on the TV/VCR/DVD
Press the POWER button to turn on the
TV/VCR/DVD.
NOTES:
2 Select the channel number
Press the CHANNEL button K or L to select your
desired channel number or press the number on the
remote control.
Note for using the Number button on the remote
control:
Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
•
When setting the Picture Control, the Game mode
will be cancelled.
•
Make sure ...
¡You must procede single-digit channel numbers
with a zero (For example: 02, 03, 04 and so on).
¡When selecting cable channels which are higher
than 99, press +100 first, then press the last two
digits. (Example: to select channel 125, first press
“+100” then press “2” and “5”).
TV/VCR/DVD power must be turned on.
•
1 Select “PICTURE CONTROL”
Press the PICTURE button on the remote control.
Remember: If the TV/VCR/DVD is connected to a
cable box or satellite box, the TV/VCR/DVD must
be on CH3 or CH4, then the channel to be viewed
must be selected on the cable box or satellite box.
2 Select item you want to adjust
Press the Arrow button K or L until desired control
is displayed.
BRIGHT
CONTRAST
COLOR
TINT
3 Adjust sound
Press the VOLUME button X or
Y
BRIGHT
–
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +
to adjust the volume.
SHARPNESS
VOLUME 20
C
C
C
C
C
C
C
C
C
C
C
C
3 Adjust the picture control
NOTES:
Press the Arrow button s or B to adjust to your
If you press the CHANNEL button K or L in the
DVD mode, you can change the TV channels.
Even if you turn off the TV/VCR/DVD in the
DVD mode, when you turn it on again, it will go
into the TV/VCR mode.
•
desired level.
Arrow Button
{
Arrow Button
B
to decrease
brightness
to increase
brightness
BRIGHT
to increase
contrast
to decrease
contrast
CONTRAST
DEGAUSSING
to pale
to purple
to soft
to brilliant
to green
COLOR
TINT
TV/VCR
Magnetism from nearby appliances and speakers
might affect the color of the TV picture.
to clear
SHAPNESS
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this fea-
ture.
•
If this happens, move this TV/VCR/DVD away from
the appliance. If the color is still not correct, unplug
the power cord, then plug it in again 30 minutes later
or so.
- 19 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOSED CAPTION SYSTEM
- TV/VCR SETUP -
1 Select “CAPTION”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CAPTION”.
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TV/VCR
B
You can view specially labeled (cc) TV programs,
movies, news and pre-recorded tapes with either a
dialogue caption or text display.
TIME SEARCH
INDEX SEARCH
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used,
usually for a second language if available.
2 Select your desired caption menu
- TV/VCR SETUP -
Press the ENTER button until your
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
desired caption menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION1]
ZERO RETURN
B
TIME SEARCH
INDEX SEARCH
3 Exit the caption setting mode
NOTE:
Press the SETUP button on the remote control to
return to TV mode.
Not all programs are broadcast with closed captions.
Your TV/VCR/DVD is designed to provide error free
closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are
likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions
errors are listed below:
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] and [2], select [OFF] using the
ENTER button. Press the SETUP button on the
remote control to return to TV mode.
Automobile ignition noise
Electric motor brush noise
Weak snowy reception on TV screen
Multiplex signal reception displaying picture
•
•
•
•
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 sec-
onds.
It will also disappear when the MUTE button is
pressed and when the PAUSE button is pressed
while recording.
ghosts or airplane flutter.
Playback of poorly recorded or worn VCR tapes.
NOTE:
•
If the TV/VCR/DVD displays a
black box on the TV screen, this
means that the TV/VCR/DVD is
set to the TEXT mode. To clear
screen, select [CAPTION1], [CAP-
TION2] or [OFF].
•
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this fea-
ture.
•
Make sure ...
TV/VCR/DVD’s power must be turned on.
•
- 20 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
V-CHIP SET UP SUB RATINGS
When you select the ratings of TV-Y7,TV-PG,TV-14
or TV-MA you will have the option of selecting sub
rating categories.
V-CHIP SET UP
TV/VCR
V-CHIP SET UP
- TV/VCR SETUP -
1 Select “V-CHIP SET UP”
Make sure ...
•
TIMER PROGRAMMING
SETTING CLOCK
Press the SETUP button on the
remote control.
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TV/VCR/DVD is turned on.
B
Press the Arrow button K or L to
select “V-CHIP SET UP”. Then
press the ENTER button.
TIME SEARCH
INDEX SEARCH
1 Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”.
Then press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B
2 Enter Access code
ACCESS CODE
TIME SEARCH
INDEX SEARCH
Use the number buttons on the
remote control to enter the access
code. (Default code is 0000.)
_
_
_
_
2 Enter Access code
Use the number buttons on the remote
control to enter the access code.
ACCESS CODE
– V-CHIP SET UP –
3 Select “TV RATING”
Press the Arrow button K or L to
select “TV RATING”.
_
_
_
_
B TV RATING
MPAA RATING
CHANGE CODE
For the first time set-up or in the
•
event the TV/VCR/DVD has lost
power, enter the default code of
the numbers: 0000.
Then press the ENTER button.
– V-CHIP SET UP –
4 Selecting “Sub-Ratings”
Press the Arrow button L to select the sub-rating you
3 Select “TV RATING”
Press the Arrow button K or L to
select “TV RATING”.
B TV RATING
MPAA RATING
CHANGE CODE
wish to block. Then, press the ENTER button twice.
When you select [TV-Y7]:
•
Then press the ENTER button.
TV–Y7
FV
[BLOCK]
[BLOCK]
Press the Arrow button L or K to
select “FV” (Fantasy Violence).
Then press the ENTER button to
select [BLOCK] or [VIEW].
When you select [TV-PG], [TV-
14] or [TV-MA]:
B
4 Blocking TV programs
Press the Arrow button K or L to
select “TV rating” that you wish to
block.
Press the ENTER button to turn it
[BLOCK].
B
TV–Y
TV–Y7
TV–G
TV–PG (
TV–14
TV–MA(
[VIEW]
(
)
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
)
)
)
•
•
(
TV–PG
[BLOCK]
B
D
L
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Press the Arrow button L or K to
select “D”(Suggestive Dialog),
“L”(Coarse Language),
S
V
When you select the rating category and turn it
•
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
“S”(Sexual Situation), or “V”(Violence). Then
press the ENTER button to select [BLOCK] or
[VIEW].
When you turn “TV-Y” to [VIEW], all ratings will
turn to [VIEW] automatically.
•
Note: When you select [TV-MA], “D” does not
appear on the TV screen.
The sub-ratings which set to
B
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
(
)
[VIEW]
Selection
TV-Y
Rating Category Explanations
Appropriate for all children
[VIEW]
[BLOCK] appears next to the rat-
ing category in the TV rating
menu.
[BLOCK]
[BLOCK]
[BLOCK]
TV-Y7
TV-G
Appropriate for children seven and older
General Audience
TV-PG
TV-14
Parental Guidance suggested.
Unsuitable for children under 14
5 Exit the V-Chip setting mode
Press the SETUP button on the remote control to
enter the setting and exit the screen.
TV-MA Mature audience only
5 Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
- 21 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING V-CHIP BLOCKED PRO-
GRAMMING
Note: To change the rating, the TV must be turned to
a station that is not protected. If the (PROTECTED)
appears on the screen, please change the channel to a
station that is not protected.
5 Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
1)Follow steps [1] and [2].
CHANGE ACCESS CODE
2)Press the Arrow button K or L to select "TV RAT-
ING". Then press the ENTER button. Select a TV
rating to be unblocked by pressing the Arrow but-
ton K or L.
Then press the ENTER button to unblock the rating.
3)Press the SETUP button on the remote control to
exit the screen.
To change access code, follow the steps.
1 Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “V-CHIP
SET UP”.
Then press the ENTER button.
MPAA RATING SET UP
2 Enter Access code
ACCESS CODE
- TV/VCR SETUP -
Use the number buttons on the remote
1 Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”. Then
press the ENTER button.
TIMER PROGRAMMING
_
_
_
_
SETTING CLOCK
CHANNEL SET UP
control to enter the access code.
The default code is 0000.
USER’S SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– V-CHIP SET UP –
3 Select “CHANGE CODE”
Press the Arrow button K or L to
select "CHANGE CODE". Then
press the ENTER button.
TV RATING
MPAA RATING
B CHANGE CODE
2 Enter Access code
Use the number buttons on the
remote control to enter the access
code.
ACCESS CODE
_
_
_
_
4 Enter New code
NEW CODE
Use the number buttons to enter
your desired access code in the
NEW CODE space. Then enter the
same code in the CONFIRM
CODE space. V-CHIP SET UP
screen appear on the screen.
X X X X
CONFIRM CODE
– V-CHIP SET UP –
3 Select “MPAA RATING”
Press the Arrow button K or L to
point to “MPAA RATING”.
Then press the ENTER button.
_
_
_
_
TV RATING
B MPAA RATING
CHANGE CODE
If you enter wrong code, repeat step 4, making
sure you enter the same new code exactly in the
confirm code space.
•
4 Select your desired item
Press the Arrow button K or L to
point to your desired item.
G
[VIEW]
PG
[VIEW]
PG–13
R
NC–17
X
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
Then press the ENTER button to
select [BLOCK] or [VIEW].
5 Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
Selection
G
Rating Category Explanations
General Audience
Note: If you unplug the power cord or power failure
occurs, the changed access code will be lost and will
return to default (0000). Change your access code
again as necessary.
PG
PG-13
R
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompa-
nying parent or adult guardian
No one under 17 admitted
NC-17
X
Mature audience only
When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
When you turn “G” to [VIEW], all ratings will turn
to [VIEW] automatically.
•
•
- 22 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
MTS(Multi-Channel Television sound)SYSTEM
You can record or listen to a program in MTS stereo.
CHECKING THE SELECTED MTS MODE
TV/VCR
When you play a VHS tape, or receive a broadcast
on the TV/VCR/DVD tuner channel you are watching,
the status shown below will appear when you press
the DISPLAY button on the remote control.
1) When a program is broadcast in stereo, STEREO
appears on the TV screen.
2) When a program is broadcast in second audio,
SAP appears on the TV screen.
3) When a program broadcast both in stereo and sec-
ond audio, STEREO and SAP appear on the TV
screen.
NOTE: Although a program may be broadcast in
both stereo and second audio, you cannot
record in both stereo and second audio at
the same time.
B
PLAY
HIFI
12:00AM
CH 123
STEREO/SAP
4)
3)
2)
1)
4) While the TV/VCR/DVD is set in HIFI stereo
mode and playback mode. HIFI appears on the
TV screen. While the TV/VCR/DVD is set in
monaural(MONO) mode, HIFI disappears from
the TV screen.
SP
COUNT
0:00:00
Second Audio Program, which means your
program, can also be received in a second
language or sometimes a radio station.
SAP
NOTE: If you play non-HIFI tapes while the
TV/VCR/DVD is set in HIFI, HIFI will
disappear from the TV screen and the
TV/VCR/DVD will play automatically in
monaural.
High Fidelity which produces better sound
than standard stereo TV/VCR/DVDs.
HIFI
MTS RECORDING/MONITOR MODE
TV/VCR
Type of broadcast Display on
STEREO/SAP
Hi-Fi audio track(2-channel) Normal audio
the TV screen SELECTION
L-channel
R-channel
track
Regular
-None-
-Invalid-
Mono
Mono
Mono
(monaural audio)
Stereo broadcast
Bilingual broadcast
STEREO
SAP
-Invalid-
STEREO*
L
R
L+R
Main audio
program
Main audio
program
Main audio
program
SAP*
Sub audio
program
Sub audio
program
Sub audio
program
Stereo & Bilingual
broadcast
STEREO
SAP
STEREO*
SAP*
L
R
L+R
sub audio
program
sub audio
program
sub audio
program
*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.
- 23 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING THE MTS SYSTEM
TV/VCR
Make sure ...
TV/VCR/DVD power must be turned on.
TO SELECT MONO MODE
•
You can change the selection to “MONO” if you
want to listen to HIFI tapes in normal audio play-
back.
TO SELECT HIFI MODE
1) Press the SETUP button on the remote control.
1 Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”. Then
press the ENTER button.
- TV/VCR SETUP -
Press the Arrow button K or L to point to “USER’S
SET UP”. Then press the ENTER button.
2) Press the Arrow button K or L to point to
“VCR AUDIO”.
3) Press the ENTER button until [MONO] appears.
4) Press the SETUP button on the remote control to
return to TV mode.
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B
TIME SEARCH
INDEX SEARCH
2 Select“VCR AUDIO”
Press the Arrow button K or L to
point to“VCR AUDIO”.
– USER’S SET UP –
RENTAL
[OFF]
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[HIFI]
[STEREO]
TO SELECT STEREO, SAP, OR MONO
B
1 Select “USER’S SET UP”
- TV/VCR SETUP -
Press the SETUP button on the
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
3 Select [HIFI]
Press the ENTER button until
[HIFI] appears.
– USER’S SET UP –
INDEX SEARCH
RENTAL
[OFF]
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[HIFI]
[STEREO]
B
– USER’S SET UP –
2 Select “TV AUDIO”
Press the Arrow button K or L to
point to“TV AUDIO”.
RENTAL
[OFF]
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[HIFI]
[STEREO]
4 To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
B
3 Select [STEREO], [SAP], or [MONO]
Press the ENTER button until [STEREO], [SAP], or
[MONO] appears.
NOTES:
Normally “HIFI” should be selected for playback
•
with HIFI sound.
When you play non-HIFI tapes, the TV/VCR/DVD
will play automatically in the monaural mode.
The TV/VCR/DVD records automatically MTS
broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
•
4 To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
•
NOTES:
You must select the recording mode,either TV
•
AUDIO [STEREO] or [SAP] when you record a
broadcast.
“MTS RECORDING/MONITOR
Refer to
MODE”.
If you select second audio when second audio is
not available, the TV/VCR/DVD will record nor-
mal audio.
The TV/VCR/DVD records automatically MTS
broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
•
•
- 24 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CASSETTE
This TV/VCR/DVD will operate with any cassette that has the
mark. For best results,
we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
INSERTING A CASSETTE
Avoid moisture. Moisture condensation may occur
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the TV/VCR/DVD. The
TV/VCR/DVD will automatically turn on.
•
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your TV/VCR/DVD, wait until the tape has
warmed to room temperature and the moisture has
evaporated.
Window
Avoid extreme heat, high humidity and magnetic
fields.
•
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
•
•
WRONG
CORRECT
TWO DIFFERENT TAPE SPEEDS
REMOVING A CASSETTE
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/play-
back time using T60, T120 or T160 tapes in each
mode.
1)In the Stop mode, press the STOP/EJECT button
on the TV/VCR/DVD. The cassette will eject.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
Tape Speed
Type of tape
SP mode
Recording/Playback Time
T60
1 hour
3 hours
T120
T160
2 hours 2-2/3 hours
6 hours 8 hours
SLP mode
ERASE PREVENTION
Note: You can play back a tape recorded in LP mode
(Long Play).
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tab
If you decide to record on
the tape again, cover the
hole with plastic tape.
Plastic Tape
NOTE:
• In DVD mode, Whether the cassette is with tab or
without tab you insert, it doesn’t start playing until
you press the PLAY button.
In TV/VCR mode, if the cassette without tab is
inserted, playback will automatically start.
- 25 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
NORMAL PLAYBACK
SLOW MOTION
TV/VCR
TV/VCR
Press the PAUSE button, then press the F.FWD
g
Make sure ...
button to start the playback in slow motion. The
TV/VCR/DVD power must be turned on.
•
TV/VCR/DVD mutes the sound during slow motion.
Press the PLAY button to return to normal playback.
NOTE: If it is left in the Slow mode for more than
five minutes, the TV/VCR/DVD will automatically
go into the Stop mode.
1 Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/VCR/DVD will start playback automatically.
STILL PICTURE
B
PLAY
2 To begin playback
Press the PLAY button.
TV/VCR
You can view a still picture on the TV screen during
playback (the Still mode). Press the PAUSE button
during playback. Only tapes recorded in the SLP
mode will show the least amount of lines. Press the
PLAY button to return to playback.
3 To stop playback
STOP
NOTES:
Press the STOP button when play-
back is completed.
You can advance the picture one frame at a time by
•
pressing the PAUSE button during the Still mode.
If it is left in the Pause mode for more than five
minutes, the TV/VCR/DVD will automatically
switch to the Stop mode.
•
NOTES:
If you press the PLAY button (of the TV/VCR side)
in the DVD mode, you can start the VCR playback.
If you press the SELECT button during the VCR
playback, it will stop and the mode will change to
the DVD mode. In addition, the same function
operates with the DVD side PLAY button or the
OPEN/CLOSE button.
•
VERTICAL HOLD CONTROL
•
TV/VCR
In the Pause/Still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
the CHANNEL button K or L.
NOTE:
If there are video noise lines on the screen, see Tracking
Adjustment section.
TRACKING ADJUSTMENT
TV/VCR
Tracking adjustment will be set automatically
(Digital Tracking function) when you start play-
back.
•
However when playing pre-recorded tapes or tapes
•
recorded on other VCR, noise lines (black and
white streaks) may appear on the playback picture.
If this occurs, you can adjust the tracking control
manually by pressing the CHANNEL button K or
L until the streaks disappear. To return to the DTR
function, stop the tape once and start playback
again.
You can reduce the noise lines by pressing the
•
CHANNEL button K or L in slow mode too.
Tracking adjustment in Slow mode will not be set
automatically.
- 26 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL PLAYBACK
Make sure ...
AUTO REPEAT PLAYBACK
TV/VCR/DVD’s power must be turned on.
Insert a prerecorded tape.
•
•
TV/VCR
The TV/VCR/DVD has the auto repeat function that
allows you to repeat a tape indefinitely without
touching the PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the begin-
ning to a blank part, which is blank for more than
10 seconds.
RENTAL PLAYBACK
TV/VCR
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1 Select “USER’S SET UP”
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
Press the SETUP button on the
CHANNEL SET UP
- TV/VCR SETUP -
1 Select “USER’S SET UP”
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
remote control.
Press the SETUP button on the
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then press the ENTER button.
remote control.
INDEX SEARCH
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then press the ENTER button.
INDEX SEARCH
2 Set “RENTAL” to [ON]
Press the Arrow button K or L to
point to “RENTAL”.
Press the ENTER button until [ON]
appears.
USER’S SET UP
–
–
B
RENTAL
[ON]
2 Select “ALL” or “BLANK”
Press the Arrow button K or L to
point to “REPEAT PLAY”.
USER’S SET UP
–
–
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[HIFI]
[STEREO]
RENTAL
[OFF]
B
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[ALL]
[OFF]
[HIFI]
[STEREO]
Press the ENTER button repeatedly
until your desired selection [ALL]
or [BLANK] appears.
3 Exit the Rental setting
Press the SETUP button on the remote control to
return to the TV mode.
3 Exit the Repeat Play setting
Press the SETUP button on the remote control to
return to the TV mode.
4 Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
Once you select the Rental mode, it stays in effect
even after you turn off the TV/VCR/DVD.
4 Start playback
Press the PLAY button to start the Repeat Play.
“REPEAT PLAY B” appears.
•
Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/VCR/DVD.
•
TO CANCEL THE RENTAL MODE
If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
•
Repeat steps [1] and [2], select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV
mode.
If there is a power failure of any kind, the
tv/vcr/dvd will retain its memory for this feature.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV
mode.
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this fea-
ture.
- 27 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
SEARCH
Make sure ...
TIME SEARCH
TV/VCR/DVD power must be turned on.
•
Insert a tape.
•
TV/VCR
The Time Search function makes it possible to quick-
ly advance the tape to your desired position simply
by entering the exact amount of playback time you
want to skip.
ZERO RETURN
TV/VCR
This function allows you to search easily a beginning point
that you want to review by rewinding or fast forwarding.
NOTES:
Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
This function will not operate in recording mode.
This function is not operative when a cassette tape
is not inserted in the TV/VCR/DVD.
In the example below: To watch a program before/
after 2 hour 50 minutes from the present position, in
either direction.
NOTE:
•
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
•
•
1 Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
2 Reset the counter to 0:00:00
Press the C.RESET button repeatedly.
1 Insert a tape
3 Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is
completed.
2 Select “TIME SEARCH” mode
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “TIME SEARCH”.
Then press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
4 To activate “ZERO RETURN” mode
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
- TV/VCR SETUP -
Press the SETUP button on the
TIMER PROGRAMMING
SETTING CLOCK
B
TIME SEARCH
remote control.
Press the Arrow button K or L to
point to “ZERO RETURN”.
Then press the ENTER button.
CHANNEL SET UP
INDEX SEARCH
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
B
3 Enter your desired time
Press the Arrow button K or L until
your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
The counter will appear on the TV screen.
The tape will automatically stop when the counter
returns to 0:00:00.
TIME SEARCH
2 : 50
PICTURE SEARCH
If you wish to cancel the Time
Search at this point, press the SETUP button on the
remote control.
TV/VCR
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD g or REW h button during play-
back. (in the SP / LP / SLP modes)
4 Begin Time Search
By pressing the Arrow button s or B, the
TV/VCR/DVD will rewind or fast forward to the
specified point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
NOTE:
g
h
If you press the F.FWD
or REW
button
•
on the front panel in the DVD mode, the VCR for-
ward or reverse will start. Please press the STOP /
EJECT button once to stop it, twice to eject it.
TO CANCEL THE TIME SEARCH at this
point
Press the STOP/EJECT button on the TV/VCR/DVD
or the STOP button on the remote control. This will
delete the selected time.
2)Press it again and the TV/VCR/DVD will now search
in super high speed. (in the LP / SLP modes only)
NOTE:
•
Tapes recorded in the SP or LP mode will dis-
play a noise bar on the TV screen and the picture
may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
- 28 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX SEARCH
1 Select “INDEX SEARCH”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “INDEX SEARCH”. Then
press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TV/VCR
This feature provides a method of indexing the start-
ing point so that it can be easily returned to in either
fast forward or rewind mode.
TIME SEARCH
INDEX SEARCH
B
The index mark will be made automatically when
•
the RECORD button is pressed. It will also be
marked at the starting point of Timer recording and
OTR.
2 Enter your desired number
Press the Arrow button K or L until
the number of programs that you
want to skip appears.
INDEX SEARCH
0 3
The index mark will not be recorded if the PAUSE
button is pressed and released during recording.
The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 min-
utes for SLP recording.
•
(Example: “03” for 3 programs)
•
The Index Search mode will be
canceled if the procedures are not activated in 30
seconds.
•
In some cases, the index mark at the beginning of
video tape cannot be detected.
•
3 Begin Index Search
Press the Arrow button s or B. The TV/VCR/DVD
begins rewinding or fast forwarding to the beginning
of desired program.
NOTE: Every time an index signal is skipped, the
number in the program indicator decreases by one.
Example: You are watching program number 4 and
want to fast forward to program number 7. You
must skip three programs.
CURRENT PLAYBACK PROGRAM
Beginning of tape
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7
End of tape
4 After Index Search
When the preset program is reached, the
TV/VCR/DVD will start playback automatically.
4
3
2
1
1
2
3
A video cassette must be inserted in the
TV/VCR/DVD for this function to work.
•
INDEX MARK
The number of Index Searches can be set up to 20.
This function will not operate in the recording mode.
When you want to cancel the Index Search while
in progress, press the STOP button.
•
•
•
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
TV/VCR
TV/VCR
When the end of a tape is reached during record-
ing, playback, or fast-forward, the tape will auto-
matically rewind to the beginning. After rewinding
finishes, the TV/VCR/DVD will eject the tape and
turn itself to off.
•
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time will
not change on a blank tape or blank portions on the
tape.)The “–” indication will appear when the tape has
rewound further than “0:00:00” on the tape counter.
This function is operative when Repeat Play is set
to the [OFF] position.
The tape will not auto-rewind during timer record-
ing or One Touch Recording.
•
•
- 29 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Make sure ...
TV/VCR/DVD power must be turned on.
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
•
•
NOTES:
This TV/VCR/DVD will ONLY record and view the same channel.
This TV/VCR/DVD cannot record the contents from the built-in DVD.
•
•
SKIPPING UNWANTED
NORMAL RECORDING
SCENES DURING RECORDING
TV/VCR
TV/VCR
You can ONLY watch the same TV program that is
being recorded.
Press the PAUSE button to tem-
PAUSE
porarily stop recording.
Press the PAUSE or RECORD but-
ton to resume recording.
NOTES:
1 Select the channel to be recorded
CH 10
Press the number buttons on the
SP
remote control or the CHANNEL
button K or L.
Remember: If the TV/VCR/DVD
is connected to a cable box or satel-
lite box, the TV/VCR/DVD must be on CH3 or CH4,
then the channel to be recorded must be selected on
the cable box or satellite box.
After five minutes, the
TV/VCR/DVD will automatically switch to the
Recording mode to prevent tape damage.
•
If “CLOSED CAPTION (ON)” is selected, the On-
Screen Display will appear for 5 seconds, then dis-
appear.
•
2 Select the tape speed
Press the SPEED button to select
the desired tape speed (SP/ SLP).
SP
REC
3 Begin recording
Press the RECORD button.
SP
4 Stop recording
Press the STOP button when recording is completed.
- 30 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
Push(es) Display
1 push
Recording length
(normal recording)
OTR (One Touch Recording)
2 pushes
3 pushes
0:30
1:00
30 minutes
60 minutes
TV/VCR
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/VCR/DVD.
17 pushes
8:00
480 minutes
Make sure ...
TV/VCR/DVD power must be turned on.
Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape
to the point at which you want to begin recording.)
NOTES:
You cannot start OTR with the remote control.
Recording starts immediately when the REC/OTR
button is pressed.
•
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
•
TV/VCR
You can make copies of video tapes made by friends
or relatives for your enjoyment.
You can not copy a DVD to a videotape.
•
•
When the REC/OTR button is pressed 18 times, the
TV/VCR/DVD returns to the Normal Recording mode.
To stop the OTR operation, press the STOP button
on the TV/VCR/DVD or on the remote control.
•
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
•
Connect your TV/VCR/DVD and a Source (Playing)
VCR using the following diagram.
To show the remaining time, press the DISPLAY
•
button on the remote control so that “OTR”
appears on the TV screen. (It will show up
momentarily then disappear.)
[Fig.8]
[The TV/VCR/DVD]
Recording stops when 0:00 is reached.
•
•
REW
PLAY
F.FWD
STOP/EJECT
HEADPHONE VIDEO
L
-
AUDIO
-
R
Please note that in the SLP mode maximum record-
ing time, assuming the tape is started at the begin-
ning, is 8 hours using T-160 (or 6 hours using T-120).
If the tape runs out before the end time, the
TV/VCR/DVD will switch to the Stop mode
immediately, ejects the tape and turns itself off.
•
[Ex: Source (playing)
VCR or camcorder]
If you press the POWER button during OTR, the
TV/VCR/DVD continues recording until the select-
ed length is reached.
•
AUDIO
L
Audio/Video
adapter cable
(not supplied)
OUT
IN
R
VIDEO
OUT
IN
1 Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL button K or L.
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to
record over, into the TV/VCR/DVD’s cassette
compartment.
3)Press the SPEED button on remote control for the
TV/VCR/DVD to select the desired recording
speed (SP/SLP).
4)Press the CHANNEL button K or L on the
TV/VCR/DVD until “AUX” appears on the screen.
5)Press the RECORD button on the TV/VCR/DVD.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/VCR/DVD’s front panel controls whenever pos-
sible. The remote control might affect the source
(Playing) VCR’s playback operation.
Remember: If the TV/VCR/DVD is connected to a
cable box or satellite box, the TV/VCR/DVD must
be on CH3 or CH4, then the channel to be recorded
is selected on the cable box or satellite box.
2 Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3 Begin OTR
Press the REC/OTR button on the
OTR(2 : 30)
TV/VCR/DVD as many times as
needed. The recording length will be
determined by the number of times
you press the REC/OTR button. Each
SP
7)To stop copying, press the STOP/EJECT button on
the TV/VCR/DVD, then stop the tape on the
source VCR or camcorder.
additional push will increase the
recording time by 30 minutes. It is set up to 8 hours.
- 31 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER
AUTOMATIC TIMER
RECORDING
1 Select “TIMER PROGRAMMING”
- TV/VCR SETUP -
Press the SETUP button on the
remote control.
B
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
TV/VCR
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Confirm “TIMER PROGRAM-
MING” is pointed by pressing the
Arrow button K, and press the
ENTER button.
You may set the TV/VCR/DVD to start and end a
recording while you are away. You can set 8 pro-
grams to record on specific days, daily or weekly
within a 1 year period.
TIME SEARCH
INDEX SEARCH
If you have not yet set the clock, “MANUAL
CLOCK SET” appears. If so, follow steps [3] to
[8] on pages 15-17. Then set the timer recording.
In the example below, the timer is being set to record:
•
DATE:
July 4th, 2004
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL:
TAPE SPEED:
CH61
SP
2 Select your desired program
position (1~8)
Press the Arrow button K or L to
select the desired program position.
Then press the Arrow button B.
– TIMER PROGRAMMING –
CH DATE
BEGIN END
Make sure ...
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
If a cable box or satellite box is connected with the
TV/VCR/DVD you will be limited to record only one
channel, and the channel selector on the
•
B
TV/VCR/DVD must be selected to the output channel
of the boxes CH 3 or CH 4 and then the actual chan-
nel to be recorded must be selected on the boxes.
Clock must be set to the correct time and date
before setting the timer.
TV/VCR/DVD power must be turn on to program it.
Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
3 Set the channel number
Press the Arrow button K or L until
the desired channel number
appears. (Example: CH61)
Then press the Arrow button B.
Remember: If the TV/VCR/DVD
is connected to a cable box or satellite box, the
TV/VCR/DVD must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box or
satellite box.
– TIMER PROGRAMMING –
CH DATE BEGIN END
•
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
•
•
B
The channel you want to record is properly set in
advance. (See page 18.)
•
Avoid over lap of programs ...
There is a chance that a program will not be record-
ed, when programs overlap;
4 Select once, every day or weekly recording
For once recording :
– TIMER PROGRAMMING –
The program with an earlier start has priority.
Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
•
•
CH DATE
BEGIN END
Press the Arrow button K (up)
until the desired date appears.
(Example: “7/04” for July 4th).
Then press the Arrow button B.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 7/04 SUN -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
B
The illustration below demonstrates the sequence
of recordings.
•
Program 1
Program 2
Program 3
10:00AM - 11:00AM
9:00AM - 10:00AM
9:30AM - 12:00PM
For every day recording : To record a TV program
at the same time on the same channel every day.
(Example: Monday through Sunday)
– TIMER PROGRAMMING –
CH DATE
BEGIN END
Recording Sequence
Press the Arrow button L (down)
until “EVRY DAY” appears.
Then press the Arrow button B.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 EVRY DAY -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
B
9:30AM-12:00PM
For weekly recording : To record a TV program at
9:00AM
10:00AM
11:00AM
12:00PM
the same time on the same channel every week.
*Recording period is SHADED
(Example: every Monday)
– TIMER PROGRAMMING –
CH DATE
BEGIN END
Press the Arrow button L (down)
until “EVRY” and your desired
day of the week appear together.
Then press the Arrow button B.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 EVRY MON -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
B
- 32 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER PROGRAM EXTENSION
5 Set beginning hour
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the Arrow button K or L until
the desired hour appears.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
TV/VCR
61 7/04 SUN 7:12P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
(Example: “ 7, PM” for 7:30PM)
Then press the Arrow button B.
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
– TIMER PROGRAMMING –
CH DATE BEGIN END
2)Repeat step [1] on page 32.
6 Set beginning minute
3)Press the RECORD button and select the desired
program using the Arrow button K or L.
4)Press the RECORD button again.
Press the Arrow button K or L until
the desired minute appears.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 SUN 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
(Example: “30” for 7:30PM)
Then press the Arrow button B.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the PAUSE but-
ton on the remote control. The recording time
returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automati-
cally be set to the SLP mode.
7 Set end hour
Press the Arrow button K or L until
the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then press the Arrow button B.
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:30PM- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 SUN 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
– TIMER PROGRAMMING –
CH DATE BEGIN END
8 Set end minute
Press the Arrow button K or
L
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50PM- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
5)Press the ENTER or RETURN button to exit the
setting menu. Then press the SETUP button on the
remote control to return to original mode.
61 7/04 SUN 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
until the desired minute appears.
(Example: “50” for 8:50PM)
Then press the Arrow button B.
B
TO CORRECT A PROGRAM
9 Set the tape speed
Press the Arrow button K or
until the desired tape speed
appears. (Example: SP)
While setting a program; press the Arrow button
s to go back one step and enter the correct num-
bers using the Arrow button K or L.
After setting a program;
•
– TIMER PROGRAMMING –
CH DATE BEGIN END
L
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50PMSP
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 SUN 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
•
1)Press the POWER button.
2)Repeat steps [1] - [2] on page 32.
3)Press the Arrow button B (or press the Arrow
button s to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the Arrow button K or L.
4)Press the POWER button to set automatic timer
recording.
10 Finish setting the program
Press the ENTER or RETURN button. The program
is now completed.
To set another program, repeat steps [2] to [10].
Press the SETUP button on the remote control to
•
•
return to original mode.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
11 Set the timer
Press the POWER button to set automatic timer
recording. The RECORDING indicator lights up.
After setting a program;
1)Press the POWER button.
•
You must turn off the TV/VCR/DVD to activate
automatic timer recording.
•
2)Repeat steps [1] ~ [2] on page 32 and select a
program you want to cancel.
3)Press the C.RESET button.
4)Press the SETUP button on the remote control to
return to TV mode.
If power is not turned off and you continue watch-
ing TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
While recording is in progress;
•
1)Press the POWER button.
2)Press the STOP/EJECT button on the
TV/VCR/DVD.
- 33 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
TO CHECK THE BEGIN/END TIME
1)Press the POWER button so that the Recording
indicator goes off.
2)Press the SETUP button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the ENTER button. The details of programs
appear on the TV screen.
3 Auto Return will begin
When all the timer recordings are completed, the
TV/VCR/DVD will rewind to the beginning of the
recorded program(s).
NOTE:
If you press the POWER button while tape is
rewinding, the Auto Return will stop.
•
5)Press the SETUP button on the remote control to
return to TV mode.
4 Watch the recorded program
Press the PLAY button.
HINTS FOR AUTOMATIC
TIMER RECORDING
TO CANCEL THE AUTO RETURN
MODE
TV/VCR
Repeat steps [1] and [2], select [OFF] using the
ENTER button.
Make sure the channel you want to record is prop-
erly set in advance.
•
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this fea-
ture.
It is not necessary to press the RECORD button for
timer recording.
Recording begins automatically at the Start time.
The display will not be turned on when the programmed
recording begins. To watch the currently recorded TV
program or to play a DVD disc, press the POWER but-
ton to turn on the display and use the SELECT button to
choose the TV/VCR mode or the DVD mode.
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
If the erase-prevention tab is removed, the cassette will
be ejected when the POWER button is pressed to off.
If the tape runs out before the end time, the
TV/VCR/DVD will switch to the Stop mode
immediately and the tape will be ejected.
•
•
•
SLEEP TIMER
TV/VCR
The Sleep Timer function turns off the
TV/VCR/DVD without using the POWER button
after a desired period of time.
NOTE:
•
•
This function does not operate during Recording
mode.
•
•
1 Select “SLEEP TIMER”
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears.
AUTO RETURN
TV/VCR
2 Set sleep time
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
Press the SLEEP button until your
desired sleep time appears.
Each additional push will increase
the time by 30 minutes up to 120
minutes.
After 5 seconds, exit the Sleep Timer setting.
SLEEP 120 MINUTES
1 Select “USER’S SET UP”
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
Press the SETUP button on the
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then press the ENTER button.
TO CANCEL THE SLEEP TIMER
INDEX SEARCH
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears. Press the SLEEP button
until “SLEEP 0 MINUTES” appears.
2 Set “AUTO RETURN” to [ON]
Press the Arrow button K or L to
point to “AUTO RETURN”.
Press the ENTER button until [ON]
appears.
USER’S SET UP
–
–
RENTAL
[OFF]
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
B
[ON]
[HIFI]
[STEREO]
- 34 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
When the Closed Caption mode is OFF:
When the Closed Caption mode is ON:
Counter mode: After 5 seconds, only the counter
remains. To clear it, press the DISPLAY button.
Clock mode: After 5 seconds, only the clock and
the channel number remain. To clear them, press
the DISPLAY button.
The On Screen Display disappear after 5 seconds.
This is true even if the MUTE button is pressed or
the PAUSE button is pressed while recording.
•
•
•
•
OFF mode
Clock/Counter mode
OFF mode Counter mode
Clock mode
STOP
STOP
5:40PM
CH2
STOP
5:40 PM
CH2
SP
COUNT 0:12:34
SP
SP
COUNT 0:12:34
After 5 seconds
After 5 seconds
5:40PM
CH2
COUNT 0:12:34
Counter
remains
Clock & Channel
remains
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
TV Display
5A
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
A
B
14
15
CATV channel
TV Display
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CATV channel
R
S
T
U
V
W
W+1
37
W+2
38
W+3
39
W+4
40
W+5
41
W+6
42
W+7
43
W+8
44
W+9
45
TV Display
31
32
33
34
35
36
CATV channel
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display
CATV channel
TV Display
CATV channel
TV Display
76
77
78
79
80
81
82
83
84
85
W+59 W+60 W+61 W+62 W+63 W+64
100 101 102 103 104 105
86
87
88
89
90
W+55 W+56 W+57 W+58
A-5
95
A-4
96
A-3
97
A-2
98
A-1
99
CATV channel
TV Display
91
92
93
94
CATV channel
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
TV Display
106
W+80 W+81 W+82 W+83 W+84
121 122 123 124 125
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CATV channel
TV Display
- 35 -
EN
1C29
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this
TV/VCR/DVD.
[
]
DVD
Data on a DVD is divided into sections called "titles" and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs and these playback con-
ditions take priority over user operations on this
TV/VCR/DVD. If a function you selected does not run as
desired, refer to the manual accompanying the disc.
¡
¡
¡
¡
¡
¡
DVD video
DVD+R/RW*
CD-R/RW*
DVD-R/RW*
Audio CD
MP3*
* Depending on the types or the writing method of the
medium some discs can not be played.
Example
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs
made on personal computers or on DVD recorders may
not be played back properly due to the factors such as
scratches, dirt or special properties of the disc.
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
• Discs made on personal computers may not be played
back properly due to the different environment or the
settings of the application you use. We recommend
always to use the standardized, rightly formatted discs.
(Please contact the sales agency for more detail).
[
]
AUDIO CD
This TV/VCR/DVD conforms to the NTSC color system.
You cannot play discs recorded in other color systems
such as PAL or SECAM.
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
¡Some discs include region codes as shown below.
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on TV/VCR/DVD with the
same region code.
The following discs cannot be played back on this
TV/VCR/DVD.
[
]
MP3
Data on an MP3 is divided into sections called "groups",
and then into subsections called "tracks", each of which is
given a group or track number.
¡
¡
¡
DVD with region codes other than 1 or ALL.
DVD-ROM
Example
Group 1
Group 2
DVD-RAM (Never play back, otherwise malfunc-
tion may result.)
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
¡
¡
¡
¡
¡
CD-ROM
VSD
CDV (Only plays back the audio part.)
CD-G (Only plays back the sound.)
CD-I (Never play back, otherwise malfunction
may result.)
¡
¡
SACD
Photo CD (Never play back, otherwise malfunc-
tion may result.)
¡
Video CD (Never play back, otherwise malfunc-
tion may result.)
Any other discs without compatibility indications.
–
–
EN
36
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A DISC
BASIC PLAYBACK
GENERAL FEATURES
DVD-V
CD
MP3
DVD-V
D
VD may contain menus to navigate the disc and
Getting started
access special features. Press the appropriate number
buttons or use the Arrow button (K/L/s/B) to high-
light your selection in the DVD main menu and press
the ENTER button to confirm.
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
1
Press the POWER button.
¡The power will turn on.
NOTES
¡Select DVD mode by pressing the SELECT button on
the remote control. Then operate the DVD functions.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
2
3
Press the OPEN/CLOSE button to open disc
loading tray.
Place the chosen disc in the tray, with the
label facing up.
DISC MENU
DVD-V
1
Press the DISC MENU button.
¡The DVD main menu will appear.
2
3
If the feature is not available,
may appear on the TV screen.
symbol
4
Press the PLAY button.
¡The tray will close automatically and playback will
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
the PLAY button.
If disc menu is available on the disc, audio lan-
guage, subtitle options, chapters for the title
and other options will appear for selection.
¡When you playback a DVD which features a title
menu, it may appear on the screen. In this case, refer
to “TITLE MENU”.
4
Press the Arrow button (K/L/s/B) to
select an item and the ENTER button to
confirm selection.
5
Press the STOP button to stop playback.
TITLE MENU
DVD-V
NOTES
¡When the DVD mode has been switched to the
TV/VCR mode, the DVD mode shuts down first and
then TV picture and sound appears in about 4 seconds.
Similarly, when the POWER button is pressed to turn
off in the DVD mode, this mode shuts down first and
then the TV/VCR/DVD’s power is turned off.
¡A “prohibited icon” may appear at
the top-right on the TV screen dur-
ing operation, warning that a pro-
hibited operation has been encoun-
tered by the DVD or the disc.
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title, or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
1
Press the TITLE button.
¡The title menu will appear.
2
3
If the feature is not available,
may appear on the TV screen.
symbol
Press the Arrow button (K/L/s/B) to
select an item and the ENTER button to
confirm selection.
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVD-Vs
¡Press the DISC MENU button to call up the DVD menu.
¡Press the TITLE button to call up the title menu.
NOTE
¡Contents of menus and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
EN
–
–
37
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
FAST FORWARD/REVERSE
SEARCH
RESUME
DVD-V
CD
MP3
DVD-V
CD
MP3
1
During playback, press the STOP button.
¡Resume message will appear on the TV screen.
1
During playback, press and hold the g or
h button for a few seconds.
¡“ g 1” or “h 1” appears on the screen.
2
Press the PLAY button, playback will resume
from the point at which playback was stopped.
2
To select another speed, repeat step1 until
your required speed appears on the screen.
¡To cancel resume, press the STOP button twice.
¡If TV/VCR/DVD is turned off, resume function will
be cancelled.
¡For MP3, playback will resume from the beginning
of the track at which playback was stopped.
¡For DVDs, fast forward/reverse search speed is dif-
ferent depending on the disc. Approximate speed is
1(×2), 2(×8), 3(×50) and 4(×100).
¡For audio CDs, approximate speed is ×16.
¡For MP3, approximate speed is ×8
¡When you use buttons on the TV/VCR/DVD front
panel, use the SKIP G/ SEARCH g or
SKIP H/ SEARCH h button.
PAUSE
DVD-V
CD
MP3
3
To return to normal playback, press the
PLAY button.
1
During playback, press the PAUSE button.
¡Playback will pause and sound will be muted.
2
To continue playback, press the PLAY button.
SLOW FORWARD /
SLOW REVERSE
STEP BY STEP PLAYBACK
DVD-V
DVD-V
1
2
During playback, press the PAUSE button.
1
During playback, press the PAUSE button.
¡Playback will pause and sound will be muted.
Press and hold the g or h button for a
few seconds.
¡“
1” or “
1” appears on the screen.
2
3
The disc goes forward by one frame each
time the PAUSE button is pressed.
3
To select another speed, repeat step2 until
your required speed appears on the screen.
To exit step by step playback, press the
PLAY button.
¡Slow forward or reverse speed varies with the disc.
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).
¡When you use buttons on the TV/VCR/DVD front
panel, use the SKIP G / SEARCH g or
SKIP H / SEARCH h button.
4
To return to normal playback, press the
PLAY button.
EN
–
–
38
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
SEARCH FUNCTION
TRACK SEARCH
TIME SEARCH
CD
MP3
DVD-V
CD
There are three ways to begin playback on an Audio
CD and MP3 at a specific track.
1
2
During playback, press the SEARCH MODE
button three times (CD: twice) to display the
Time Search on the TV screen.
Using the Number buttons on the remote control
Within 30 seconds, enter a desired disc
time using the Number buttons on the
remote control.
1
Press the Number buttons to enter the
desired Track number.
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡Playback will start at the specified time.
¡Press the CLEAR button to erase the incorrect input.
¡When there is no need to enter a number, “0”
appears automatically. For example, “ 0 : 0
appears in the Time Search display if the total time
of the disc is less than 10 minutes.
¡To play track 26, press +10, 2, 6.
:
”
-
- -
Using the SEARCH MODE button
MARKER SETUP SCREEN
1
Press the SEARCH MODE button.
¡The track search display appears.
DVD-V
CD
2
Within 30 seconds, select a desired track
number using the Number buttons on the
remote control.
Use markers to memorise your favorite places on a
disc.
¡For single digits press 0 first.
¡Playback will start at the selected track.
1
Press the SEARCH MODE button four times
(CD: three times) during playback.
Using the SKIP
H
G
buttons
¡The display screen and Markers will appear on the
TV screen.
During playback, press the SKIP G button to move
the next track. Press it repeatedly to skip subsequent
tracks. Press the SKIP H button to go back to begin-
ning of the current track. Press it repeatedly to go to
the previous tracks.
¡If the SKIP button is pressed while the playback is
paused, the playback will be paused again after skip-
ping to the next track.
2
3
Press the Arrow button (s /B) to select 1, 2,
3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “
- - -
:
:
” appears in the display.
-
- - - -
When you reach the desired point, press the
ENTER button.
NOTE
¡The SKIP
¡The Title or Track and elapsed playing time will
appear in the TV screen.
H
G buttons are not available when
playback is stopped.
4
To return to the Marker later, press the
SEARCH MODE button four times (CD: three
times) during playback and the Arrow but-
ton (s /B) to choose the desired marker,
then press the ENTER button.
TITLE / CHAPTER SEARCH
DVD-V
1
Press the SEARCH MODE button once for
the Chapter search, twice for the Title
search during playback.
NOTES
¡Opening the disc tray or turning off the power or
selecting AC at step 2 and pressing the ENTER but-
ton will erase all Markers.
_/2
¡To clear a marker, using the Arrow button (s /B),
position the cursor on to the marker number to be
cleared and press the CLEAR button.
¡You can mark up to 10 points.
2
Enter the desired chapter/title number using
the Number buttons on the remote control.
¡Playback will start at the selected Chapter or Track.
¡Press the CLEAR button to erase the incorrect input.
¡For single digits press 0 first.
5
Press the SEARCH MODE or RETURN but-
ton to exit.
EN
–
–
39
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL PLAYBACK FUNCTION
REPEAT
PROGRAM
REPEAT is available only during playback.
CD
You may determine the order in which tracks will play.
REPEAT TITLE / CHAPTER
DVD-V
1
In stop mode, press the MODE button.
¡The PROGRAM screen will appear.
To activate the repeat function, press the
REPEAT button during playback.
¡The repeat mode changes as described below every
time you press the button.
2
Press the Arrow button ▲ or ▼ to select a
track, then press the
TOTAL
CHAPTER
(current chapter repeat) (current title repeat)
TITLE
OFF
(repeat off)
ENTER button.
¡Press the CLEAR button to
erase the most recently entered
program.
NOTES
¡Repeat Title/Chapter is not available with some
scenes.
3
4
Repeat step 2 until you have selected all the
tracks you want to play in the program.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
Press the PLAY button to play the pro-
grammed tracks.
REPEAT TRACK
NOTES
CD
¡While the program is being played back, the STOP
works as follows.
To activate the repeat function, press the
REPEAT button during playback.
¡The repeat mode changes as described below every
time you press the button.
¡Press the STOP button once and then the PLAY but-
ton again, playback will restart from the point where
the STOP button was pressed. (Program continued)
¡Press the STOP button twice and then the PLAY button
again, playback will restart from the track in the usual
way. (Program cleared)
TRACK
(current track repeat)
ALL
OFF
(repeat off)
(entire disc repeat)
¡Up to 99 programs can be entered.
¡To erase all programs at once, select ALL CLEAR at
the bottom of the list at Step2.
NOTES
¡If you like to repeat the current track in the program,
press the REPEAT button repeatedly until
TRACK appears during playback. If you like to
repeat the entire program press the REPEAT button
¡Repeat setting will be cleared when moving to other
track.
¡Repeat playback does not function during repeat A-B
playback.
repeatedly until
ALL appears during playback.
REPEAT A-B
RANDOM PLAYBACK
DVD-V CD
CD
1
2
Press the REPEAT A-B button at your cho-
sen starting point.
A- appears briefly on the TV screen.
This shuffles the playing order of tracks instead of
playback in the sequence.
¡
¡
1
In stop mode, press the MODE button twice.
Press the REPEAT A-B button again at your
chosen end point.
¡RANDOM screen appears.
RANDOM
CD-DA
TOTAL 0:45:55
A-B appears briefly on the TV screen and the
repeat sequence begins.
RANDOM PROGRAM
no indication
-
-
-
-
PLAY
3
To exit the sequence, press the REPEAT A-
B button.
NOTES
2
Press the PLAY button to start random playback.
NOTE
¡The repeat A-B section can only be set within the cur-
rent title (for DVDs) or current track (for audio CDs).
¡Repeat A-B is not available with some scenes in DVD.
¡To cancel the A point which was set, press the
CLEAR button.
¡If you like to repeat the current track in the random
selection, press the REPEAT button repeatedly until
TRACK appears during playback. If you like to
repeat the entire random selection press the
REPEAT button repeatedly until
during playback.
¡Repeat A-B playback does not function during title,
chapter, track or all repeat playback.
ALL appears
EN
–
–
40
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A MP3 DISC
MP3 PLAYBACK
PROGRAM
MP3
MP3
This feature allows you to program an MP3 disc to
play in a desired sequence.
When a CD with MP3 files is in the TV/VCR/DVD,
press the DISC MENU button to call up the MP3 menu
on the TV screen.
1
In stop mode, press the MODE button.
¡The PROGRAM screen will appear.
1
In stop mode, press the Arrow button (K/L)
to select the desired
2
Select a desired track using the Arrow but-
ton (K/L/s/B). Then, press the ENTER
button.
group or track.
folder name 1
folder name 2
¡If a group is selected, press
the Arrow button or the
folder name 3
folder name 4
file name 1
file name 2
file name 3
B
¡Press the Arrow button B when you want to go to
the next hierarchy.
¡Press the Arrow button s when you want to go back
to the previous hierarchy.
¡Press the CLEAR button to erase the most recently
entered program.
ENTER button to go on to the
track selection screen. Press
the Arrow button (K/L) to
choose a track, then press the ENTER button.
¡If a track is selected, press the ENTER button to start
playing tracks. Starting from the one you’ve just
chosen the subsequent tracks will be played.
folder name 1
3
Repeat step 2 until you have selected all the
Tracks you want to play in the program.
¡Press the TITLE button to return to the first item.
2
Press the STOP button to stop playback.
NOTES
4
Press the PLAY button to start programmed
playback.
¡Folders are known as Groups; files are known as
Tracks.
¡MP3 files are accompanied by
NOTES
¡While the program is being played back, the STOP
button as follows.
3
icon.
¡Press the STOP button once and then the PLAY but-
ton again, playback will restart from the point where
the STOP button was pressed. (Program continued)
¡Press the STOP button twice and then the PLAY button
again, playback will restart from the track in the usual
way. (Program cleared)
¡Maximum of 255 folders can be recognized.
¡Maximum of 512 files can be recognized.
¡Up to 8 hierarchies can be created.
This TV/VCR/DVD recommends the use of files
recorded at the below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
¡To erase all programs at once, select ALL CLEAR at
the bottom of the list at Step2.
REPEAT
MP3
RANDOM PLAYBACK
MP3
REPEAT is available only during playback.
1
In stop mode, press the MODE button twice.
¡RANDOM screen appears.
1 To activate the repeat function, press the
REPEAT button during playback.
¡The repeat mode changes as described below every
time you press the button.
2
Press the PLAY button to start random play-
back.
TRACK
(current track
repeat)
GROUP
(current group
repeat)
ALL
(entire disc
repeat)
OFF
(repeat off)
NOTE
¡Repeat setting will be cleared when moving to other
track.
EN
–
–
41
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETTINGS
SUBTITLE LANGUAGE
CAMERA ANGLE
DVD-V
DVD-V
The TV/VCR/DVD allows you to select a language for Some DVD discs contain scenes which have been shot
subtitles during DVD disc (if available) playback. simultaneously from various angles. You can change
the camera angle when the (
screen.
) icon appears on the
1
2
Press the SUBTITLE button during playback.
Press the SUBTITLE button repeatedly to
select your desired subtitle language.
1
Press the ANGLE button during playback.
¡The selected angle will be displayed on the display
¡The subtitle language will appear on the display bar
at the top of the TV screen.
bar at the top of the screen.
2
Press the ANGLE button repeatedly to
select your desired angle.
3
To turn off subtitles, press the SUBTITLE
button repeatedly until OFF appears.
NOTES
BLACK LEVEL SETTING
¡
Some discs allow audio language setting/subtitle language
setting on the disc menu. (Operation varies between discs,
so refer to the manual accompanying the disc.)
DVD-V
¡If the desired language is not shown after pressing
the SUBTITLE button several times, the disc does
not have subtitles in that language.
Adjust the Black Level Settings to make the black
parts of the picture brighter.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 44.)
1
Press the MODE button during playback.
OFF
2
Press the ENTER button to switch OFF.
ON: Makes the dark parts brighter.
AUDIO LANGUAGE
OFF: Shows the original picture as recorded.
DVD-V
The TV/VCR/DVD allows you to select a language
during DVD disc (if multi languages are available)
playback.
3
Press the MODE button twice or the
RETURN button to exit.
NOTE
¡The setting will be saved even if the TV/VCR/DVD
1
2
Press the AUDIO button during playback.
is turned off.
Press the AUDIO button repeatedly to select
your desired language.
VIRTUAL SURROUND
NOTE
DVD-V
CD
MP3
¡Pressing the AUDIO button may not work on some
DVDs with multiple audio languages (e.g. DVDs
which allow audio language setting on the disc menu).
You can enjoy surround-sound effect over two speak-
ers on this TV/VCR/DVD.
STEREO SOUND MODE
1
Press the V.SURR button once or the MODE
button twice (CD/MP3: once) during play-
CD
back.
OFF
1
Press the AUDIO button repeatedly during
playback to select between STEREO, L-CH
or R-CH.
2
3
Press the ENTER button to set it 1 (Natural
effect) or 2 (Emphasized effect) or OFF.
¡
STEREO - both right and left channels are active (stereo)
L-CH - only left channel is active
R-CH - only right channel is active
Press the V. SURR or RETURN button to
exit.
NOTE
NOTE (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
¡If the Virtual Surround setting is ON, the sound mode
will be fixed to STEREO and can not be changed.
EN
–
–
42
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
THE ON-SCREEN INFORMATION
DVD-V
CD
MP3
You can check the information about the current disc by pressing the DISPLAY button on the remote control.
For DVD-Vs
For audio CDs
1
Press the DISPLAY button during playback
to show current Chapter.
1
Press the DISPLAY button during playback
to show the current Track.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
9/49
0:00:00 -0:03:30
2
Press the DISPLAY button again to show
current Total Track.
2
Press the DISPLAY button again to show
current Title.
¡The elapsed and remaining playing time of the cur-
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
rent title will be displayed.
3
Press the DISPLAY button again to exit the
display.
3
Press the DISPLAY button again.
¡The BIT RATE and the current repeat setting will be
displayed.
For MP3
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
1
Press the DISPLAY button during playback.
¡The name of the file currently in play will be dis-
played.
4
Press the DISPLAY button again to exit the
display.
2
Press the DISPLAY button again to show
the track number, the elapsed time, the
repeat status and the playback status at the
top of the screen.
¡
will be displayed when repeat play has been
selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates Disc repeat
3
Press the DISPLAY button again to exit the
display.
EN
–
–
43
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE DVD SETUP ITEMS
LANGUAGE SETTING
Language
Code Language
Code
DVD-V
A-B
L-N
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
4748 Laothian
4747 Latin
4752 Latvian;Lettish
6563 Lingala
4759 Lithuanian
4764 Macedonian
5471 Malagasy
4765 Malay
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
Language options are not available with some discs.
1
Press the SETUP button twice in STOP
mode so that the DVD SETUP menu
appears.
4771 Malayalam
4772 Maltese
4847 Maori
¡If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
5167 Marathi
4860 Moldavian
5072 Mongolian
4854 Nauru
SETUP
QUICK
CUSTOM
INITIALIZE
4855 Nepali
4864 Norwegian [NOR]
4853
5971 Occitan
4851 Oriya
Oromo(Afan)
5759 Panjabi
4947 Pashto;Pushto
7254 Persian
4961 Polish
5464 Portuguese [POR]
4965 Quechua
5047 Rhaeto-Romance
6058 Romanian [RUM]
5160 Russian [RUS]
5161
5166 Samoan
Sangho
5261 Sanskrit
5256 Scots Gaelic
5255 Serbian
Bulgarian
Burmese
Byelorussian
O-R
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
C-E
2
Press the Arrow button L to select CUS-
Cambodian
Catalan
TOM, then press the ENTER button.
Chinese [CHI]
Corsican
Croatian
¡CUSTOM mode will appear.
Czech
3
Press the Arrow button (K/L) to select
“LANGUAGE”, then press the ENTER button
to confirm.
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
S
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
SETUP
CUSTOM
F-H
Faroese
Fiji
LANGUAGE
DISPLAY
AUDIO
Finnish [FIN]
French [FRE]
Frisian
PARENTAL
5264 Serbo-Croatian
5271 Sesotho
5358 Setswana
5747 Shona
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
4
Press the Arrow button (K/L) to select the
next items, then press the ENTER button.
5051 Sindhi
5158 Singhalese
5758 Siswat
5360 Slovak
AUDIO: Sets the audio language.
Gujarati
Hausa
Hebrew
5367 Slovenian
5447 Somali
5569 Spanish [SPA]
5455 Sundanese
5467 Swahili
SUBTITLE: Sets the subtitle language.
DISC MENU: Sets the language for DVD menu.
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
5
Press the Arrow button (K/L) to select a
setting, then press the ENTER button.
Swedish [SWE]
5565
5560 Tagalog
5547 Tajik
5551 Tamil
5557 Tatar
5347 Telugu
5566 Thai
T
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
¡If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to
enter the code for the desired language. (Refer to the
language code list.)
¡Only the languages supported by the disc can be
selected.
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
5647 Tibetan
5669 Tigrinya
5760 Tonga
5765 Tsonga
5757 Turkish [TUR]
6469 Turkmen
5771 Twi
Kazakh
6
Press the SETUP button to exit.
Kinyarwanda
Kirghiz
Kirundi
NOTE
6460
U-Z
¡Language Setting for Audio and Subtitle is not avail-
able with some discs. Then use the AUDIO and the
SUBTITLE buttons. Details are on page 42.
Korean [KOR]
Kurdish
5761 Ukrainian
5767 Urdu
Uzbek
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
TO CHANGE THE ON-SCREEN MENUS
You can access the TV/VCR SETUP menu by pressing
the SETUP button from the DVD mode. Refer to
“SELECTING THE LANGUAGE” on page 15 to
changing the on-screen menus.
Yoruba
Zulu
If you choose a Language that has a 3 letter language
code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 42. If
you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
EN
–
–
44
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY SETTING
AUDIO SETTINGS
DVD-V
DVD-V
You can change certain aspects of the DVD display Choose the appropriate Audio settings for your equip-
screens and on-screen messages on the TV screen.
ment as it only affects during the playback of DVD
discs.
1
Press the SETUP button twice in STOP mode
so that the DVD SETUP menu appears.
1
Press the SETUP button twice in STOP mode
so that the DVD SETUP menu appears.
¡If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
¡If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
SETUP
SETUP
QUICK
CUSTOM
INITIALIZE
QUICK
CUSTOM
INITIALIZE
2
Press the Arrow button L to select CUS-
TOM, then press the ENTER button.
¡CUSTOM mode will appear.
2
Press the Arrow button L to select “CUS-
TOM”, then press the ENTER button.
3
Press the Arrow button (K/L) to select “DIS-
PLAY”, then press the ENTER button to con-
firm.
¡CUSTOM mode will appear.
3
Press the Arrow button (K/L) to select
“AUDIO”, then press the ENTER button to
confirm.
SETUP
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
SETUP
CUSTOM
LANGUAGE
DISPLAY
AUDIO
4
Press the Arrow button (K/L) to select the
below items, then press the ENTER button.
PARENTAL
TV MODE:
QUICK
4
Press the Arrow button (K/L) to select the
below items, then press the ENTER buttons.
¡Press the Arrow button (K/L) for an item selection,
then press the ENTER button.
¡Select 4:3 LETTER BOX for black bars to appear on
top and bottom of the screen.
DRC (Dynamic Range Control):
¡To compress the range of soft to loud sound.
¡The default setting is ON.
¡Select 4:3 PAN & SCAN for a full height picture
with both sides trimmed.
¡The default setting is 4:3 LETTER BOX.
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be acti-
vated and sound will be down sampled at 48kHz.
STILL MODE
:
¡Press the Arrow button (K/L) for an item selection,
then press the ENTER button.
¡Select “AUTO” usually.
¡If you select “FIELD”, the picture in the still mode
will be stabilized.
¡If you select “FRAME”, the picture in the still mode
will be highly defined.
DOLBY DIGITAL:
QUICK
ANGLE ICON:
Set to On when the unit is connected to a Dolby Digital
Decoder.
¡Press the ENTER button repeatedly to turn Angle
icon ON or OFF.
(ON: Output a Dolby Digital signal)
(OFF: Convert the Dolby Digital to PCM (2 channel
stereo))
¡The default setting is ON.
AUTO POWER OFF:
¡The default setting is ON.
¡Press the ENTER button repeatedly to turn Auto
Power off ON or OFF.
¡
The default setting is ON and it will turn the TV/
VCR/DVD off automatically after 15 minutes of no use.
5
Press the SETUP button to exit.
5
Press the SETUP button to exit.
EN
–
–
45
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL LEVELS
PARENTAL CONTROL
¡
ALL
All parental lock is cancelled.
DVD-V
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
Parental Control limits the disc viewing that exceed
your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
¡
Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
PARENTAL LEVEL
¡
Level 1
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s rat-
ings exceed the level you set.
Only DVD software intended for children can be
played back, with those intended for adult and
general use is prohibited.
1
Press the SETUP button twice in STOP mode
so that the QUICK SETUP menu appears.
¡If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
IF YOU FORGET THE PASSWORD
1
Press the number buttons 4, 7, 3, 7 at step 4.
Then enter your new password.
2
Press the Arrow button L to select “CUS-
TOM”, then press the ENTER button.
SETUP
¡Password will be cleared and parental level will be
set to ALL.
QUICK
CUSTOM
INITIALIZE
2
Proceed the Steps 5-7 again.
3
Press the Arrow button (K/L) to select
“PARENTAL”, then press the ENTER button.
INITIALIZE
SETUP
CUSTOM
This allows you to return all selections of SETUP
(except for PARENTAL) to their default settings.
LANGUAGE
DISPLAY
AUDIO
PARENTAL
1
2
3
Press the SETUP button twice in STOP
mode so that the INITIALIZE menu appears.
Press the Arrow button (K/L) to select “INI-
TIALIZE”, then press the ENTER button.
4
5
Enter your four-digit password then press
the ENTER button.
Select “YES”, then press the ENTER button
twice. All the settings (except for
“PARENTAL”) will be cleared.
Press the Arrow button (K/L) to select
“PARENTAL LEVEL”, then press the ENTER
button.
¡To cancel the initialization, select “NO”.
6
7
Press the Arrow button (K/L) to select the
desired level, then press the ENTER button.
4
Press the SETUP button to exit.
Press the SETUP button to exit
NOTES
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password.(in the event you forget the password, see
below)
¡To change the password, press the Arrow button
(K/L) to select CHANGE at step 5, then press the
ENTER button. Enter the four-digit password, then
press the ENTER button.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
EN
–
–
46
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
If the TV/VCR/DVD does not perform properly when operated as instructed in this Owner’s Manual, check
the TV/VCR/DVD, consulting the following checklist.
PROBLEM
CORRECTIVE ACTION
Make sure the power plug is connected to an AC outlet.
Make sure the power is turned on.
Check if the power plug is connected to an AC outlet.
Check the batteries in the remote control.
Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote.
You have to be within 23 feet of the TV/VCR/DVD.
No power
•
•
•
•
•
The TV/VCR/DVD does not
respond to the remote control
•
•
Check if the correct mode is selected. If not switch the mode by
pressing the SELECT button on the remote control,whichever you need.
TV/VCR Mode
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked
possibilities. Before arranging for service, check these items. It could save your time and money.
PROBLEM
No picture and sound
CORRECTIVE ACTION
Make sure the AC cord is connected to an AC outlet.
Check antenna connection.
Press the SELECT button on the remote control to select TV mode.
Then try other TV feature.
•
•
•
Let the TV/VCR/DVD program its tuner memory.
Adjust direction or replace antenna.
Adjust picture controls.
Adjust volume control on remote control or main unit.
Press the MUTE button to restore sound.
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust COLOR control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust CONTRAST & BRIGHT control.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
No picture or poor picture on
TV/VCR/DVD
No sound or poor sound
Bars On Screen
Picture Distorted or Blurred
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Adjust CONTRAST & BRIGHT control.
EN
–
–
47
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
Picture OK, Sound Poor
CORRECTIVE ACTION
Try a new channel, if OK, then possible station trouble.
Check for local interference.
Make sure the timer recording is set correctly.
Make sure the power is off.
Make sure the TV/VCR/DVD clock is set correctly.
Make sure the tape has an erase-prevention tab. If need, cover the
hole with plastic tape.
•
•
•
•
•
•
•
Timer recording is not possible
Cannot go into Record mode
Playback picture is partially noisy
• Adjust tracking control for a better picture using the CHANNEL
• button K or L on the TV/VCR/DVD.
• Head cleaning may be necessary. Refer to “AUTO HEAD
• CLEANING” on page 50.
No picture but the audio is OK in
playback
No operation by infrared Remote
Control
Video or color fades in and out
• Make sure the AC cord is connected to an AC outlet.
• Check batteries in remote control.
• You can not copy a copyrighted video tape. You are experiencing
when making a copy of a video tape • copy guard protection.
Different color marks on screen
Magnetism from nearby appliances and geomagnetism might affect
•
the color of the TV picture. Move the
away from the
TV/VCR/DVD
appliances, the
can repair itself automatically. If you
TV/VCR/DVD
want to repair immediately, unplug the power cord, then plug it in
again 30 minutes later or so.
CLOSED CAPTION PROBLEM
My TV/VCR/DVD is showing
captions that are misspelled.
POSSIBLE REMEDY
• You are watching a live broadcast and spelling errors made by the
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/VCR/DVD will not show
the text dialogue in its entirety or
there is a delay of what is being
said.
• Captions that are delayed a few seconds behind the actual
are common for live broadcast. Most captioning production
• companies can display a dialogue to a maximum of 220 words
• per minute. If a dialogue exceeds that rate, selective editing is used
• to insure that the captions remain up-to-date with the current
• TV screen dialogue.
My captions are scrambled with
white boxes on the TV screen.
• Interference caused by building, power lines, thunderstorms, etc.
• may cause scrambled or incomplete captions to appear.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed
as being closed captioned but none • up the actual program so that additional advertising time can be
of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating
show any captions. The tape box • company accidentally left out the captioning signals during the
mentions it being closed captioned. • copying process.
My TV screen shows a black box
on certain channels.
• You are in the TEXT mode. Select CAPTION mode to CAPTION
• [OFF].
EN
–
–
48
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Mode
PROBLEM
CORRECTIVE ACTION
• Insert a correct video disc that plays on this TV/VCR/DVD.
• Press the SELECT button on the remote control to select DVD mode.
Then, try other DVD feature.
No picture
• Insert the disc.
Disc cannot be played
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
No sound
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This TV/VCR/DVD does not support DTS audio. This is not a mal-
function.
• There are some cases where pictures may be slightly distorted, which
are not a sign of a malfunction.
No DTS audio is output
Distorted picture
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
does not match the set up
•
The selected language is not available for audio or subtitles on the DVD.
This is not a malfunction
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera
angles. This is not a malfunction
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected
changed
language. This is not a malfunction.
“Prohibited icon” appears on the
screen, prohibiting an operation
CD sound dropout
• That operation is prohibited by this TV/VCR/DVD or the disc.
This is not a malfunction.
• Scratched disc. Replace the disc with an unscratched one.
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
NOTES:
Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
•
Playback from a desired track and random playback are not available during program playback.
•
EN
–
–
49
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.Please visit your local Audio/Video store and pur-
CABINET CLEANING
chase a good quality VHS Video Head Cleaner.
2.If a Video Head Cleaner does not solve the prob-
lem, please call our help line at 1-800-968-3429, to
locate an Authorized Service Center.
NOTES:
Wipe the front panel and other exterior surfaces of
the TV/VCR/DVD with a soft cloth immersed in
lukewarm water and wrung dry.
•
Never use a solvent or alcohol. Do not spray insec-
•
ticide liquid near the TV/VCR/DVD. Such chemi-
cals may cause damage and discoloration to the
exposed surfaces.
Remember to read the instructions included with
the video head cleaner before use.
•
Clean video heads only when problems occur.
•
AUTO HEAD CLEANING
SERVICING
Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
•
Should your TV/VCR/DVD become inoperative,
•
do not try to correct the problem by yourself. There
are no user-serviceable parts inside. Turn off,
unplug the power cord and please call our help line
at 1-800-968-3429, to locate an Authorized Service
Center.
Playback picture may become blurred or interrupt-
•
ed while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during play-
back, the video heads in your TV/VCR/DVD may
need to be cleaned.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
If the TV/VCR/DVD still does not perform properly when it is operated while referring to the relevant sec-
•
tions and to "TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be
dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical
pickup unit.
DISC HANDLING
Use discs which have the following logos on them.
(Optical audio digital discs.)
To clean-off, use a soft cloth.
•
•
•
•
•
•
•
•
Do not use a hard cloth since this will mar the disc.
Wipe the disc in a straight line from center to edge.
Never wipe with a circular motion.
ReWritable
Recordable
Do not use detergent or abrasive cleaning agents.
Handle the discs so that fingerprints and dust do
not adhere to the surfaces of the discs.
Always store the disc in its protective case when it
is not used.
EN
–
–
50
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Sound output:
2 speakers, 1W, 8 ohm
TV/VCR
CRT
19 inch in-line gun,
90˚ deflection tube
NTSC-M
OTHER SPECIFICATIONS
Terminals
Television system :
Closed caption system :§15.119/FCC
Antenna input:
VHF/UHF/CATV
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
Video Heads :
Tape width :
Tape speed
SP :
LP :
SLP :
Tuner channel
TV VHF Low :
TV VHF High :
TV UHF :
CATV
Rotary four-head
1/2 inch
Video input:
Audio L/R input:
Headphone:
Coaxial digital
audio output:
1/8” stereo (3.5 mm)
33.40mm/sec.
16.67mm/sec.
11.12mm/sec.
One pin jack,
500m Vpp (75 ohm)
Digital encoded
Remote control:
#2~#6
#7~#13
#14~#69
infrared light system
Operating
temperature:
5°C to 40°C
(41°F~104°F)
Power requirements: AC 120V, 60Hz
Power consumption
VHF :
5A
MID band :
SUPER band :
HYPER band :
A5~A1, A~I
J~W
W+1~W+84
(Maximum):
Picture tube:
Dimensions:
90W
19"
H:19-11/16” (500mm)
W:23-13/16” (605mm)
D:18-11/16” (474mm)
48.5 lbs (22kg)
Weight:
DVD
Product type:
Discs:
DVD Player
DVD video, Audio CD
Output signal format: NTSC color
Designs and specifications are subject to change without notice.
If there is a discrepancy between languages, the default language will be English.
•
•
EN
–
–
51
01A11
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Indicador de grabación
INDICE
Parpadea durante la grabación. Se ilumina durante el
modo de espera de grabación controlada por temporizador.
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 52
MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 52
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54
MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54
CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54
CONEXIÓN A UN AMPLIFICADOR ESTÉREO
13. Botón REC/OTR (Panel frontal) [TV/VCR P.30, 31]
Presione para empezar la grabación manual. Presione
repetidamente para empezar la grabación instantánea
(OTR).
Botón RECORD (Manda a distancia) [TV/VCR P.30]
Presione para empezar la grabación manual.
14. Botón REW (para TV/VCR)
Presione este botón para rebobinar la cinta o para ver
la imagen rápidamente en dirección de retroceso
durante el modo de reproducción. (Búsqueda en direc-
ción de retroceso)
EQUIPADO CON TOMAS DE ENTRADA DIGITAL,
PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 54
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
15. Botón F.FWD (para TV/VCR)
Presione este botón para adelantar rápidamente la cinta
o para ver la imagen rápidamente en dirección de
avance durante el modo de reproducción. (Búsqueda en
dirección de avance)
SECCIÓN DE TV/VCR
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 54
AJUSTE DE CANALES . . . . . . . . . . . . . . . . . . . . . . . . . 55
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
16. Botón STOP/EJECT
Presione este botón para detener la cinta. Presiónelo en
el modo de parada para retirar la cinta del
televisor/videograbadora/DVD.
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55
17. Ventanilla del sensor de mando a distancia
18. Toma HEADPHONE
Para conectar auriculares (no suministrados) y escuchar
en privado.
CONTROLES DE
OPERACIÓN Y FUNCIONES
19. Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una
videocámara o de una videograbadora.
PANEL FRONTAL DEL
TELEVISOR/DVD
20. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
Consulte la figura 1 de la página 9
21. Compartimiento del cassette
22. Botón PICTURE
MANDO A DISTANCIA
Presione este botón para ajustar la imagen.
23. Botones numéricos
Consulte la figura 2 de la página 9
Modo TV:
Presione dos botones para acceder directamente al
canal deseado.
VISTA POSTERIOR
No olvide presionar “0” antes de elegir un canal de un
solo dígito.
Consulte la figura 3 de la página 10
Botón +100
1. Botón POWER
Presione este botón para conectar y desconectar la ali-
mentación.
2. Botones VOLUME X/Y
Presione estos botones para controlar el nivel de volumen
del DVD y el televisor.
Presione este botón para seleccionar canales de tele-
visión por cable cuyo número sea igual o superior a 100.
Modo DVD:
Presione este botón para introducir el número deseado.
Botón +10
Presione este botón para introducir números iguales o
3. Botones SKIP (para DVD)
mayores que 10
.
Presione el botón correspondiente una vez para omitir
capítulos o pistas y desplazarse a un punto específico.
Mantenga el botón presionado para cambiar la veloci-
dad de reproducción en avance o retroceso.
24. Botón PAUSE
Hace una pausa en la reproducción del disco o cinta.
25. Botón SPEED
Presione este botón para seleccionar la velocidad de
grabación deseada: SP/SLP.
4. Botón PLAY
Inicia la reproducción del contenido del disco o cinta.
5. Botón STOP
Detiene la reproducción del disco.
6. Botón OPEN/CLOSE
Presione este botón para insertar discos en la bandeja o
retirarlos de ella.
26. Botón C.RESET
Presione este botón para poner el contador en 0:00:00.
Presiónelo también para cancelar un ajuste de progra-
ma de temporizador.
27. Botón DISPLAY
Modo TV/VCR:
7. Bandeja de carga del disco
Para visualizar el contador o el número del canal y la
fecha actual en la pantalla del televisor.
Modo DVD:
8. Indicador DVD
Se ilumina durante el modo DVD.
Indica el estado actual en la pantalla del televisor para
fines de comprobación.
9. Botón SELECT
Presione este botón para cambiar al modo TV/VCR,
modo de entrada externa o modo de DVD.
28. Botón SETUP
Presione este botón para activar o salir del modo de
menús de televisor o configuración de DVD.
10. Indicador TV/VCR
Se ilumina durante el modo TV/VCR.
29. Botón TITLE
11. Botones CHANNEL K/L
Para visualizar el menú de títulos.
Utilice estos botones para seleccionar canales memorizados.
ES
–
–
52
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
30. Botón CLEAR
ANTENAS SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena
exterior.
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a su televisor/
videograbadora/DVD, sin una caja de convertidor.
Con esta conexión podrá:
Para cancelar ajustes.
31. Botón MODE
Activa el modo de reproducción programada o el modo de
reproducción aleatoria.
32. Botón SEARCH MODE
Presione este botón para localizar un punto deseado.
33. Botón AUDIO
Presione este botón para seleccionar un idioma de
audio o el modo de sonido deseado.
1) Utilizar el mando a distancia del televisor/
videograbadora/DVD para seleccionar canales.
2) Programar uno o más canales decodificados para
grabación automática controlada por temporizador.
NOTA: Este televisor/videograbadora/DVD SÓLO
puede grabar el canal que se está viendo.
34. Botón SUBTITLE
Presione este botón para seleccionar el idioma de subtí-
tulos deseado.
35. Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
36. Botón ANGLE (modo DVD)
Presione este botón para cambiar el ángulo de la cámara
y ver la secuencia que se está reproduciendo desde un
ángulo diferente.
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
37. Botón A-B REPEAT
Si su compañía de televisión por cable le suministra
una caja de convertidor o si utiliza un sistema de
satélite, podrá utilizar la conexión básica que se
muestra en la ilustración.
Repite la reproducción de una sección seleccionada.
38. Botón RETURN
Permite volver a la operación anterior en el modo de
configuración de DVD.
Al utilizar esta conexión, también podrá grabar canales
codificados. Sin embargo, la selección de los canales
deberá hacerse con la caja de convertidor o con la caja
de satélite. Esto significa que no es posible cambiar de
canal utilizando el mando a distancia del televisor/
videograbadora/DVD. La grabación en ausencia (contro-
lada por temporizador) está limitada a un canal a la vez.
PARA GRABAR UN CANAL
39. Botón ENTER
Presione este botón para establecer un ajuste.
40. Botones de flechas
Modo TV/VCR:
Presione estos botones para seleccionar un modo de
ajuste en el menú que aparece en la pantalla del televisor.
Presiónelos también para seleccionar opciones o
establecer ajustes en un menú en particular.
Modo DVD:
CODIFICADO/DECODIFICADO
Use estos botones para hacer ajustes mientras observa
la imagen en la pantalla del televisor.
1.Ajuste el selector de canales del
televisor/videograbadora/DVD al canal de salida de
la caja de convertidor de televisión por cable o caja
de satélite. (Ej., CH3)
41. Botón DISC MENU
Muestra los menús contenidos en el DVD.
42. Botón V.SURR
2.Seleccione el canal que desea grabar en la caja de
convertidor de televisión por cable o caja de satélite.
Activar/desactivar el envolvente virtal.
43. Botón MUTE
Suprime la salida de sonido. Presiónelo de nuevo para
restablecer el sonido.
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención
del instalador de sistemas CATV para que tenga
en cuenta el Artículo 820-40 de la NEC, que pro-
porciona recomendaciones para hacer una conex-
ión a tierra apropiada y, en particular, especifica
que la tierra del cable debe conectarse al sistema
de puesta a tierra del edificio, tan cerca del punto
de entrada del cable como sea posible.
44. Botón SLEEP
Utilice este botón para ajustar el temporizador de dormir.
45. Botón SELECT
Presione este botón para cambiar entre los modos
TV/VCR y DVD. El modo seleccionado (TV/VCR o
DVD) se visualiza en el indicador del panel delantero.
46. Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por cable
o sistema de satélite.
CONEXIÓN A TOMAS DE ENTRADA
EXTERNA
47. Cable de alimentación
Conéctelo a una toma de CA estándar (120 V, /60 Hz).
NOTA: Antes de conectar el cable de alimentación a
una toma de CA estándar, retírelo del gancho
para evitar dañarlo.
Cuando vea un programa grabado en otra fuente (videograbado-
ra o videocámara), utilice las tomas de entrada de audio/vídeo
de la parte delantera del televisor/videograbadora/DVD.
Conecte las tomas de salida de audio/vídeo de otra fuente a
las tomas AUDIO L/R y VIDEO de este televisor/
videograbadora/DVD. Luego, presione los botones CHAN-
NEL K/L hasta que aparezca "AUX" en la pantalla.
NOTA:
48. Toma de salida de audio digital COAXIAL
Conéctela solamente a la entrada digital de un amplifi-
cador externo o decodificador de audio de DVD.
PREPARACIÓN PARA LA
UTILIZACIÓN
CONEXIONES DE ANTENA/CABLE
Cuando conecte una videograbadora monofónica (otra
fuente) a este televisor/videograbadora/DVD, conecte la
toma de salida de audio de la videograbadora monofónica
(otra fuente) a la toma AUDIO L de este
televisor/videograbadora/DVD. El audio saldrá igual-
mente por los canales izquierdo y derecho.
•
Consulte la figura 4 de la página 11
Consulte la figura 5 de la página 12
ES
–
–
53
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
Consulte la figura 7 de la página 14
NOTAS:
PARA INSERTAR LAS PILAS
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a
distancia en el sentido de la flecha.
2) Inserte 2 pilas "AA" en el
compartimiento de las pilas, en el
sentido indicado por las marcas de polaridad (+/-).
3) Vuelva a poner la cubierta.
Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
Consulte los manuales de instrucciones de los
componentes que va a conectar al televisor/
videograbadora/DVD.
Si conecta un decodificador Dolby Digital, ajuste
la función DOLBY DIGITAL a ON para salida de
audio en el modo de configuración.
A menos que se haga la conexión a un decodifi-
cador Dolby Digital, ajuste la función Dolby
Digital a OFF para salida de audio en el modo de
configuración. La reproducción en un
•
•
•
•
MODO DE ENTRADA EXTERNA
Al usar una señal de entrada externa (otra videograbado-
ra o una videocámara), conecte los cables de salida de
audio/vídeo del equipo externo a las tomas AUDIO L/R
IN/ VIDEO IN de su televisor/videograbadora/DVD.
Luego, presione los botón CHANNEL K o L hasta que
aparezca "AUX" en la pantalla.
televisor/videograbadora/DVD utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede causar daños a los altavoces.
CONEXIÓN A UN AMPLIFICADOR
ESTÉREO EQUIPADO CONTOMAS DE
ENTRADA DIGITAL, PLATINA MD O
PLATINA DAT (Para DVD)
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D
doble son marcas de fábrica de Dolby
Laboratories.
Utilice un cable digital coaxial de audio de venta en el
comercio especializado para hacer las conexiones de audio.
Conexión a un amplificador equipado con tomas de
entrada digital, platina MD o platina DAT.
SECCIÓN DE TV/VCR
PREPARACIÓN PARA LA
UTILIZACIÓN
Consulte la figura 6 de la página 13
NOTAS:
• La fuente de audio de un disco grabado en formato de
sonido envolvente Dolby Digital de 5,1 canales no se
puede grabar como sonido digital mediante una plati-
SELECCIÓN DE IDIOMA
TV/VCR
• nAaseMgúDreoseDdAeTd. esconectar la alimentación de todos
1
Enchufe el cordón de alimentación
del televisor/videograbadora/DVD
los componentes del sistema antes de conectar otro
• cCoomnspuolnteenlotes.manuales de instrucciones de los compo-
nentes que va a conectar al televisor/videograbadora/
televisor/videograbadora/DVD en una toma de CA
Enchufe el cordón de alimentación del
estándar.
• DAVjuDst.e la función Dolby Digital a OFF para salida de
audio en el modo de configuración. La reproducción
en un televisor/videograbadora/DVD utilizando
ajustes incorrectos puede generar ruido y distorsión, y
también puede causar daños a los altavoces.
NOTA:
Si aparecen algunas cifras en la esquina de la pan-
•
talla, pulse el botón POWER sin desenchufar el
cordón de alimentación.
Asegúrese de que ...
Pulse el botón POWER para encender el
televisor/videograbadora/DVD.
•
CONEXIÓN A UN DECODIFICADOR
DOLBY DIGITAL (para DVD)
NOTA: Esta función afecta sólo el idioma en el menú
de la pantalla y no la fuente de audio.
Si utiliza este televisor/videograbadora/DVD para
reproducir un disco DVD grabado en formato de
sonido envolvente Dolby Digital de 5,1 canales, el
televisor/videograbadora/DVD emitirá un flujo de
datos DOLBY DIGITAL desde su toma de salida de
audio digital COAXIAL. Si conecta el reproductor a
un decodificador Dolby Digital, podrá disfrutar de
una tonalidad más convincente y real, con un sonido
envolvente potente y de alta calidad similar al de los
cines.
2
Seleccione “LANGUAGE”
Pulse el botón SETUP en el mando a distancia.
Pulse el botón K o L para señalar “LANGUAGE”.
3
Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS”
Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”
con el botón ENTER.
4
Salga del modo de idioma
Pulse el botón SETUP en el mando a distancia para
volver al modo del televisor.
Utilice cables digitales coaxiales de audio
disponibles en el comercio especializado para hacer
las conexiones de audio.
ES
–
–
54
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTA: Si, por alguna razón, el menú está en inglés o
francés, pulse el botón SETUP en el mando a distancia,
pulse el botón K o L para señalar el “LANGUAGE
[ENGLISH]” o “LANGAGE [FRANÇAIS]”, a contin-
uación, pulse el botón ENTER y pulse el botón SETUP
en el mando a distancia.
1)Pulse el botón SETUP en el mando a distancia.
Pulse el botón K o L para indicar “AJUSTE
RELOJ”.
Luego, pulse el botón ENTER.
2)Pulse el botón K o L para indicar “AJUSTE
MANUAL RELOJ”.
Luego, pulse el botón ENTER.
3)Pulse el botón K o L hasta que aparezca el mes
deseado. (Ejemplo: Mayo - 05)
AJUSTE DE CANAL
TV/VCR
Luego, pulse el botón B.
Puede programar el sintonizador para buscar todos
los canales que recibe en su localidad.
4)Pulse el botón K o L hasta que aparezca el día
del mes deseado. (Ejemplo: 6 - 06)
Luego, pulse el botón B.
5)Pulse el botón K o L hasta que aparezca el año
deseado. (Ejemplo: 2004)
Luego, pulse el botón B.
6)Pulse el botón K o L hasta que aparezca la hora
deseada. (Ejemplo: 5, PM)
NOTA: El canal preparado NO es necesario cuando
esté conectado a una caja de cable o caja de satélite.
Sólo tiene que seleccionar con el selector de canal
del televisor/videograbadora/DVD al canal de salida
de la caja de cabe o caja de satélite (por ejemplo el
canal CH3). Seleccione el canal a ver en la caja de
cable o caja de satélite.
Luego, pulse el botón B.
Asegúrese de que ...
7)Pulse el botón K o L hasta que aparezca el minu-
to deseado. (Ejemplo: 40)
Pulse el botón POWER para encender el televi-
sor/videograbadora/DVD.
•
8)Pulse el botón SETUP en el mando a distancia.
Aunque los segundos no se visualizan, éstos
empiezan a contar desde 00 cuando se pulsa
SETUP en el mando a distancia. Utilice esta fun-
ción para sincronizar el reloj con la hora correcta.
1 Seleccione “AJUSTE DE CANAL”
Pulse el botón SETUP en el mando a distancia.
Pulse el botón K o L para señalar “AJUSTE DE
CANAL”.
A continuación, pulse el botón ENTER.
2 Empiece el prefijado automático
Pulse el botón K o L para señalar “AUTOPROGRA-
MACION DE CA”.
SECCIÓN DE DVD
A continuación, pulse el botón ENTER.
El sintonizador busca y memoriza todos los canales
activos en su localidad.
REPRODUCCIÓN BÁSICA
DVD-V
CD
MP3
3 Después de buscar
El sintonizador se detiene en el canal memorizado
más bajo.
Para empezar
¡Conecte la alimentación del amplificador y otros
componentes, si es necesario.
Cuando se activa AUTOPROGRAMACION DE
•
CA, donde no hay entrada de señal del televisor,
aparecerá “NO HAY SEÑAL DE TV” en la pan-
talla después de terminar la búsqueda de canales.
1
Presione el botón POWER.
¡La alimentación se conectará.
2
3
4
Presione el botón OPEN/CLOSE para abrir
la bandeja de carga del disco.
El televisor/videograbadora/DVD puede reconocer
•
los canales de TV para que sean canales de TV de
antena de cable con las condiciones de recepción.
En este caso, pruebe nuevamente con el prefijado
automático en las condiciones de recepción fina.
Ponga el disco deseado en la bandeja, con
la etiqueta hacia arriba.
Presione el botón PLAY.
¡La bandeja se cerrará automáticamente y la repro-
ducción comenzará desde el primer capítulo o pista
del disco. Si la reproducción no comienza automáti-
camente, presione el botón PLAY.
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú podrá aparecer en la pan-
talla.
AJUSTE DEL RELOJ
TV/VCR
Cerciórese...
La alimentación del televisor/videograbadora/DVD
deberá estar conectada.
•
En el ejemplo de abajo, el reloj va a ajustarse así:
FECHA: 6 de mayo de 2004
HORA: 5:40 PM
5
Presione el botón STOP para detener la
reproducción.
ES
–
–
55
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to
any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,
please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-968-3429
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
1EMN20035
T0003UD ★★★★★
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sonic Blue CD Player MVP841 User Manual
Sony Car Stereo System Model CDX 3800 User Manual
Sony Network Card TDM BT1 User Manual
SOYO Computer Hardware SY 6ZB User Manual
State Industries Water Heater 317998 002 User Manual
Sterling Plumbing Indoor Furnishings 11605 NA User Manual
Summit Refrigerator FF7LBISSTB User Manual
Sunrise Medical Mobility Aid S 626 User Manual
SVAT Electronics Security Camera VU5 User Manual
Symantec Server Security Expressions Server User Manual