Sylvania Flat Panel Television LC260552 User Manual

Español

Français

English

26” LCD TV

LC260SS2

EN Owner's Manual

Need help?

Please call toll free or visit our web site below

Appelez notre numéro gratuit ou visitez notre site web à l’adresse

FR Manuel du Propriétaire Besoin d’aide?

ES Manual del Propietario ¿Necesita ayuda? Llame por favor sin costo ó visite nuestro sitio web en

1-866-321-3927

www.sylvaniaconsumerelectronics.com



MODEL NUMBER

SERIAL NUMBER

Download from Www.Somanuals.com. All Manuals Search And Download.

English

FCC WARNING

This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful interference

unless the modifications are expressly approved in the manual. The user could lose the authority to operate this apparatus if an

unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This apparatus

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this apparatus does cause harmful interference to radio or television reception, which can be determined by turning the apparatus off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the apparatus and receiver.

3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

DECLARATION OF CONFORMITY

Trade Name: SYLVANIA

Responsible Party: FUNAI CORPORATION, Inc.

Address: 19900 Van Ness Avenue, Torrance, CA 90501 U.S.A.

Telephone Number: 1-866-321-3927

Model: LC260SS2

This Class B digital apparatus complies with Canadian ICES-003. StandardTelevision Receiving Apparatus, Canada BETS-7/NTMR-7

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

WARNING: Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnect the mains plug to shut off when find trouble or not in use.The mains plug shall remain readily operable.

This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided.

Make sure to leave a space of 4 inches (10cm) or more around this apparatus.

WARNING: To prevent injury, this apparatus must be securely attached to the wall in accordance with the instructions.

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or

climbing on it. A falling unit can cause serious injury or even death.

LAMP IN LCD CONTAINS MERCURY,DISPOSEACCORDINGTO LOCAL,STATE OR FEDERAL LAW.

• The American Academy of Pediatrics discourages television

Trademark Information

viewing for children younger than two years of age.

NOTE ABOUT RECYCLING

• This unit’s packaging materials are recyclable and

can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

• Batteries should never be thrown away or incinerated

but disposed of in accordance with your local

regulations concerning chemical wastes.

HDMI, the HDMI Logo, and High-Deﬁnition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC in the

United States and other countries.

• For product recycling information, please visit -

www.sylvaniaconsumerelectronics.com

WHEN CARRYINGTHIS UNIT

• At least 2 people are required when

carrying this unit.

• Make sure to hold the upper and bottom

frames of the unit ﬁrmly as illustrated.

Manufactured under license from Dolby Laboratories. Dolby and the

double-D symbol are trademarks of Dolby Laboratories.

TO AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

• Do not handle the AC power cord with wet hands.

• Do not pull on the AC power cord when disconnecting it from an

AC outlet. Grasp it by the plug.

ENERGY STAR^®is a joint program of the U.S. Environmental

Protection Agency and the U.S. Department of Energy helping us all

save money and protect the environment through energy efﬁcient

products and practices.

• Do not put your ﬁngers or objects into the unit.

LOCATION AND HANDLING

• Do not install the unit in direct sunlight or in a place subject to dust

or strong vibration.

Consumer Notice:

ThisTV has been set to maximize energy efﬁciency while delivering

the best possible picture using the factory installed home mode

settings.

Changing or enabling other features in thisTV (e.g. brightened

backlighting) will possibly increase energy consumption beyond the

original ENERGY STAR^®qualiﬁed limits.

• Avoid a place with drastic temperature changes.

• Install the unit in a horizontal and stable position. Do not place anything

directly on top or bottom of the unit. Depending on your external

devices, noise or disturbance of the picture and/or sound may be

generated if the unit is placed too close to them. In this case, please

ensure enough space between the external devices and the unit.

• Depending on the environment, the temperature of this unit may

increase slightly.This is not a malfunction.

• Be sure to unplug the AC power cord from the AC outlet before

moving or carrying the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Child Safety

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Features

INTRODUCTION

•

DTV/TV/CATV

You can use your remote control to select channels which are

broadcast in digital format and conventional analog format.Also,

cable subscribers can access their cableTV channels.

Contents

Important Safety Instructions

Trademark Information

Child Safety

•

Information Display (ATSC only)

You can display the title, contents and other information of the

current DTV program on theTV screen.

Autoprogram

INTRODUCTION

Features

This unit automatically scans and memorizes channels available in

your area, eliminating difﬁcult setup procedures.

Supplied Accessories

Symbols Used in this Manual

Attaching the Base

Mounting the Unit onYour Furniture

Remote Control Function

Installing the Batteries

Control Panel

Child Lock

This feature allows you to block children’s access to inappropriate

programs.

Closed Caption Decoder

Built-in closed caption decoder displays text for closed caption

supported programs.

•

MTS/SAPTuner

Audio can be selected from the remote control.

Terminals

Cable Management

Auto Standby

If there is no input signal and no operation for 15 minutes, the

unit will go into standby mode automatically.

PREPARATION

Antenna Connection

•

SleepTimer

Connection to Cable Receiver or Satellite Box

Plug In the AC Power Cord

Initial Setup

You can set the unit to go into standby mode after a speciﬁc

amount of time.

Choices for On-screen Language

Select your on-screen language:

English, Spanish or French.

WATCHINGTV

Freeze Mode

SleepTimer

Sound Functions

•

Stereo Sound Function

PLL Frequency SynthesizedTuning

Switching Each Input Mode

TV Screen Display Mode

Channel Selection

TV Screen Information

Reducing the Brightness

fun-Link Options

Provides free and easy channel selection and lets you tune

directly to any channel using the number and decimal point “ ”

•

buttons on the remote control.

•

Various Adjustment for Picture and Sound

Customizes image quality suitable for your room and sets your

sound preference.

fun-Link via HDMI Link

(HDMI Cable not Included)

fun-Link allows your other HDMI link devices to be controlled by

the HDMI cable connected to yourTV.

USING FUNCTIONS

Picture

Sound

Setup

Features

Language

•

HDMI Input

When using HDMI1 Input, you can enjoy this unit as a PC

monitor if your PC has a DVI output terminal.

•

HDMI-DVI Input

ComponentVideo Input

S-Video Input

AV Input

Digital Audio Output

Analog Audio Output

CONNECTING DEVICES

External Device Connection

USEFULTIPS

FAQ

Troubleshooting Guide

INFORMATION

Glossary

Maintenance

General Speciﬁcations

Electrical Speciﬁcation

Other Speciﬁcations

Limited Warranty

License

end of book

medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of

this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify

any person or organization of such changes.

with the

design is a registered trademark of Funai Electric Co., Ltd. and may not be used in any way without the express written consent

of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be

construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or

any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.

SYLVANIA is a registered trademark of OSRAM SYLVANIA Inc., used under license.

Download from Www.Somanuals.com. All Manuals Search And Download.

Supplied Accessories

Attaching the Base

You must attach the base to the unit to have it as a table top

unit. Be sure the front and rear of the base match the proper

direction.At least 2 people are required for these steps.

Owner’s Manual

Quick Start Guide Registration card

If you have any questions, please visit our website at

www.sylvaniaconsumerelectronics.com

^QS^ut^ickart

Check the text “FRONT” with “arrow“ on the Base’s

bottom to ensure it is being installed in the correct

direction. Spread a thick and soft cloth over a table as shown

at step 2. Place the main unit face down onto it. Make sure

not to damage the screen.

Installation

Instalación

TV base and 4 screws (M4 x 20)

Insert 2 hooks under the

bottom of the main unit

into base holes. (shown by

➁

Remote Control

(NH210UD)

Batteries

arrow ), then move the

base in the direction as

➀

(AAA, 1.5V x 2)

➀

FRONT

shown by arrow until it

➁

stops and the screw holes

are aligned. Make sure not to put the AC power cord

between the base and the unit.

Drive Phillips head screws

into the 4 threaded holes

at the bottom of the base

until they are tight.

Note

To remove the base from this unit

• If you lose the screws, please purchase M4×20 Phillips head screws

at your local store.

• If you need to replace these accessories, please refer to the part

No. with the illustrations and call our toll free customer support

line found on the cover of this manual.

• Unscrew the Phillips head screws in step 3.

After the screws are removed, move the base in the opposite

direction as shown by arrow in step 2, then pull the base up toward

the rear of the unit. Be careful not to drop the base when you

remove it.

When using a universal remote control to operate this unit.

• Make sure the component code on your universal remote control

is set to our brand. Refer to the manual accompanying your

remote control for more details.

• We do not guarantee 100% interoperability with all universal

remote controls.

Note

• When attaching the base, ensure that all screws are tightly fastened.

If the base is not properly attached, it could cause the unit to fall,

resulting in injuries as well as damage to the unit.

• Make sure to use a table which can support the weight of this unit

and is larger than this unit.

• Make sure the table is in a stable location.

• When attaching the base, ensure that “FRONT” with “arrow”

written on the bottom of the base is downward. If it’s not

downward, the 2 hooks don’t ﬁt into the base.

Symbols Used in this Manual

The following is the description for the symbols used in this

manual. Description refers to:

ATSC

: DigitalTV operation

Mounting the Unit onYour Furniture

NTSC

Screw this unit on your furniture tightly using wood screws

:Analog/CableTV operation

(not supplied) in the 2 holes at the back of the base as shown.

•

If neither symbol appears, the operation is applicable to

both.

• Recommended screw dimension : 3/16 x 3/4 inches(5.1 x 20 mm)

rear of this unit

screw holes

Note

• When you remove this unit make sure to unscrew the wood

screws from your Wood Stand, Furniture and other wood item.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Remote Control Function

(power)

p.11

➠

Press to turn the unit on and go into standby mode.

To completely turn off the unit, you must unplug the AC

power cord.

2 SLEEP

3 Number buttons

• (dot)

p.12

p.13

➠

Press to shift the subchannel from the main channel.

4 PREV CH

p.13

➠

Press to return to previously viewed channel.

5 BACK

6 OK

7 ▲/▼/◄/►(cursor)

8 MENU

9 SAP

10 VOL +/−

11 MUTE

12 SOURCE

p.14

p.11

p.15

p.12

p.13

p.12

➠

13 FREEZE

Press to freeze screen image.

14 FORMAT

p.13

➠

Press to select aspect ratio available for theTV screen.

ECO

Press to reduce power consumption.

p.14

➠

16 INFO

17 CH+/−

p.14

p.13

p.22

➠

18 RED/GREEN/BLUE/YELLOW

Functionally useful for fun-Link.

19 H (skip backward)/G (skip forward)

p.22

➠

Press to skip backward or forward chapters, titles or

tracks of the disc.

B (play)

p.22

➠

Press to begin the disc playback.

E (reverse)/D (forward)

p.22

Press to search backward or forward through the disc.

F (pause)

p.22

➠

Press to pause the disc playback.

C (stop)

p.22

Press to stop the disc playback.

OPTIONS

p.14, 22

Press to call up various menu from your fun-Link device

connected through an HDMI cable.

Installing the Batteries

Install the batteries (AAA, 1.5V x 2) matching the polarity

indicated inside battery compartment of the remote control.

Note

• Buttons in gray background (

) are not available unless you

are connected to devices that are compatible with fun-Link

function.

• We do not guarantee 100% interoperability with other brands of

HDMI link compliant devices.

Battery Precautions:

• Be sure to follow the correct polarity as indicated in the battery

compartment. Reversed batteries may cause damage to the device.

• Do not mix different types of batteries together (e.g.Alkaline and

Carbon-Zinc, or rechargeable batteries like ni-cad, ni-mh, etc) or

old batteries with fresh ones.

• If the device is not to be used for a long period of time, remove the

batteries to prevent damage or injury from possible battery leakage.

• Do not try to recharge batteries; they can overheat and rupture.

Download from Www.Somanuals.com. All Manuals Search And Download.

Control Panel

(power)

p.11

➠

Press to turn the unit on and go into standby mode.

To completely turn off the unit, you must unplug the AC

power cord.

2 CH +/−

p.13

➠

Press to select channels or move up ( )/down ( )

−

through the main menu items.

3 MENU

4 VOL +/−

p.15

p.12

➠

Press to adjust the volume up/down or move right

( )/left ( ) through the main menu items.

−

5 Standby indicator

Lights up red when the unit goes to standby mode.

6 Power on indicator

Lights up green when power is on.

−

VOL

−

7 Infrared sensor window

Receives infrared rays transmitted from the remote

control.

This indicator does not function on this unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Terminals

Side Panel

8 HDMI 2 Input jack

p.10, 24

➠

9 S-Video/CompositeVideo/Audio (L/R)

Input jacks forVIDEO

p.24, 25

➠

Rear Panel

10 Cable management

11 AC power cord

p.9

➠

p.10

12 Antenna Input jack

13 HDMI 3 Input jack

14 HDMI 1 Input jack

p.10

p.10, 24

p.10, 24, 25

HDMI connection for HDMI or DVI device.When you

connect your PC that has a DVI terminal, you can enjoy

this unit as a PC monitor.

15 ComponentVideo and Audio (L/R) Input jacks

p.10,24

➠

16 Digital Audio Output jack

p.25

17 Analog Audio (L/R) Output jacks

p.25

➠

18 Analog Audio (L/R) Input jacks for HDMI 1

p.24, 25

➠

Audio cable connection from a DVI device.

When you connect your PC that has a DVI terminal, use

a stereo mini plug conversion cable as well.

(For HDMI 1 Input jack only)

Note for service terminal

service terminal (service use only)

• Use this terminal only when a software update is necessary.

• User should not connect any devices to the service terminal such

as digital camera, keyboard, mouse, etc. (because these will not

work).

• The software update is, in most cases, handled by an authorized

service person or in some circumstances the user may be asked

to do the software update themselves.

Cable Management

Keep the cables through this holder to avoid tangling them.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection to Cable Receiver or

Satellite Box

PREPARATION

Use an HDMI or ComponentVideo cables to connect the

HDMI or the ComponentVideo Input jacks of the unit to the

HDMI or the ComponentVideo output jacks of the cable

receiver/satellite box.

No supplied cables are used with these connections:

• Please purchase the necessary cables at your local store.

If you connect to the unit’s ComponentVideo Input jacks,

connect Analog Audio cables to the Analog Audio L/R Input

jacks right beside the ComponentVideo connector jacks.

Before you connect:

Be sure your antenna or other device is connected properly

before plugging in the AC power cord.

satellite dish

Antenna Connection

Connect the RF coaxial cable on your home outlet to the

antenna input jack of this unit.

cableTV signal

including PPV

VHF/UHF

analog

HDMI cable

ANT IN

DTV antenna

RF coaxial cable

cable receiver/

satellite box

STEREO

PCM

RF coaxial cable

COMPONENT VIDEO OUT

Pb/Cb Pr/Cr

AUDIO OUT

HDMI OUT

(green) (blue) (red)

component video cables

(red/blue/green) and audio cables

You can also connect this unit to the cable receiver or satellite

box other than the HDMI or the ComponentVideo output jacks

or CompositeVideo output jack (

might have different output jacks.

p.24, 25) because they

➠

cableTV signal

Required cables and connecting methods of the cable receiver/

satellite box, or the availability channel for the clear QAM may

differ depending on the cable/satellite provider or localTV

broadcaster.

For more information, please contact your cable/satellite provider

or localTV broadcaster.

Once connections are completed, turn on the unit and begin

initial setup. Channel scanning is necessary for the unit to

memorize all available channels in your area. [Initial Setup]

p.11

➠

Note

• If you have any question about the DTV’s antenna, visit

www.antennaweb.org for further information.

• Use an HDMI cable with the HDMI logo (a certiﬁed HDMI cable).

High Speed HDMI cable is recommended for the better compatibility.

• Depending on your antenna system, you may need different types

of combiners (mixers) or separators (splitters) for HDTV signal

the minimum RF bandpass on these devices is 2,000MHz or 2GHz.

• For your safety and to avoid damage to this unit, please unplug the

RF coaxial cable from the antenna input jack before moving the

unit.

• If you did use an antenna to receive analogTV, it should also

work for DTV reception. Outdoor or attic antennas will be more

effective than a set top or inside antenna.

• To switch your reception source easily between antenna and cable,

install an antenna selector.

• If you are not receiving a signal from your cable service, contact the

Cable provider.

Plug In the AC Power Cord

Make sure that the AC power cord must be plugged to an AC

outlet after all the necessary connections are made.

Caution:

• Do not connect the AC power cord to a power supply outside

the indicated voltage of this unit (AC 120V).

Connecting the AC power cord to a power supply outside of this

range may result in ﬁre or electrical shocks.

Note

• Each time you plug in the AC power cord, no operations will be

performed for a few seconds.This is not a malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Use ◄/► to select the desired location setting, then press

OK.

These operations are accessible by remote control.

Some may also be accessible by controls on the main unit.

[Home] is ENERGY STAR^®qualiﬁed setting.

Initial Setup

Select “Retail” or “Home” for your location.

This section will guide you through the unit’s initial setting

which includes selecting a language for your on-screen menu

and autoprogram, which automatically scans and memorizes

viewable channels.

Home

Retail

Select

Before you begin:

Make sure the unit is connected to antenna or cable.

After making all the necessary connections,

press to turn on the unit.

• It may take a few moments to turn on the unit for the

first time.

• [Initial Setup] menu appears automatically after the

unit is turned on.

• Select [Retail] store, the unit will be set up with

predefined setting for retail displays. In this setting, the

power consumption may possibly exceed the limited

requirement of the ENERGY STAR^®qualification.

• Select [Home], the unit is set to maximize the energy

efficiency for home setting and it can be adjusted

through a choice of picture and sound quality according

to your preference.

• When the initial setup is completed, the lowest

memorized channel with the confirmation message of

the location setting will be displayed on theTV screen.

• You must set [Home] in step 4. Otherwise, [Picture]

and [Sound] settings you adjusted will not be

memorized after the unit goes into standby mode.

Use ▲/▼ to select the on-screen language from the

choices (English/Español/Français) on the right side of the

TV screen, then press OK.

Use ▲/▼ to select [Antenna] forTV channels or [Cable]

for CATV channels, then press OK.

Initial Setup

Antenna

Make sure the antenna is connected to ''ANT. IN'' jack.

Note

Cable

Skip

Select your signal source.

• If you are not receiving a signal from your cable service, contact

the Cable provider.

• If you press or MENU during autoprogram, this setup of TV

channels will be canceled.

• The initial autoprogram function can be executed for either

[Antenna] or [Cable] only once.When you change the

Antenna

Cable

ANT.IN

connection (Antenna/Cable), set [Autoprogram] again.

• If there is no signal input from the antenna terminal and no

p.17

➠

Select

Back

Skip

operation for several seconds after you turn on the unit, helpful

hints appears. Follow the instructions listed on theTV screen.

• [Autoprogram] will begin.

Initial Setup

Please wait while the system is scanning for channels.

Auto programming may take more than 20 minutes to

complete.

Retry

No channel is registered.

Try Autoprogram again?

Later

Verify that you have a cable connected to the "ANT. IN" jack

on the back of the TV, the channel installation process

searches this connection. If you are using a cable or satellite

box, please confirm the input which you have connected to the

box and press “SOURCE” key on the remote control to select

the appropriate source input.

Digital channels

Analog channels

0 ch

Skip

Select

Skip

After an initial setup is completed...

• If you want to scan the channels automatically again.

[Autoprogram] p.17

➠

• You can add the desired cable and analog channels

unmemorized by autoprogram.

[Add Channels]

p.18

➠

• If you want to change to another language.

[Language] p.23

➠

• If you want to change the location setting.

[Location] p.23

➠

Download from Www.Somanuals.com. All Manuals Search And Download.

WATCHINGTV

Freeze Mode can freeze the image shown on theTV screen for 5 minutes.

Press FREEZE to freeze the image.

Freeze

•

The sound output will not be paused.

To cancel freeze mode, press any buttons except y.

SleepTimer

can set the unit to go into standby mode after an incremental period of time.

Press SLEEP repeatedly to change the amount of time (increases

the time by 30 minutes up to 120 minutes).

Sleep

120min.

Press SLEEP once to call up the display for checking the remaining time.

•

To cancel sleep timer, press SLEEP repeatedly until [Sleep Off] is

displayed.

Sound Functions describe how to change the audio or the audio language as

well as the volume.

Volume Adjustment

Use VOL+/− to adjust the volume.

Volume

will be displayed for a few seconds when adjusting the volume.

Silence Mode

Press MUTE to turn off the sound temporarily.

Mute

will be displayed for a few seconds.

•

Press MUTE again or VOL+/− to recover the original

volume.

Switching Audio Mode

ATSC

Press SAP repeatedly to cycle through the available audio languages.

• Available languages differ depending on the broadcast.

• [Other] is displayed when the audio language cannot be

acquired, or the acquired languages are other than English,

Spanish or French.

11.1

English 1/3

NTSC

Press SAP to display the currently selected audio mode.

While receiving an MTS broadcast, press repeatedly to cycle through

the available audio channel.

SAP / STEREO

e.g.) When all audio are available

STEREO : Outputs stereo-audio

SAP : Outputs second audio program

MONO : Outputs mono-audio

SAP / STEREO

SAP / MONO

SAP / STEREO

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Switching Each Input Mode can easily switch with the remote control betweenTV (ATSC or NTSC) and external

devices when they are connected to the unit.

Press SOURCE or CH+ repeatedly to cycle through the input modes.

Source

e.g.)

TTVV

HDMI1

Video

11.1

Video

Component

HDMI1

HDMI2

HDMI3

Vide

HDMI3

onent

I1onent

DTV/TV channel

(or PC input)

•

Pressing CH− reverses the direction of the input modes.

TV Screen Display Mode

5 types of display modes can be selected when the broadcasting station is sending 16:9 or 4:3 video signal.And 3 types of display

modes can be selected for PC input signal.

Press FORMAT

repeatedly to switch theTV aspect ratio.

Normal displays a 16:9 picture at its original size.

For 16:9 video signal

4:3 displays a 16:9 picture at a 4:3 size; the picture is

shortened horizontally. Sidebars appear on both edges

of the screen.

Movie Expand displays a 16:9 picture that is vertically

stretched to ﬁll the screen.This only crops out the top

of the picture.

Normal

4:3

Movie Expand

Zoom displays a 16:9 picture at its maximum size

without changing its horizontal and vertical ratio.

Wide displays a horizontally stretched picture.This

crops out the left and right sides of the picture.

Wide

Zoom

Normal displays a 4:3 picture at its original size.

Sidebars appear on both edges of the screen.

For 4:3 video signal

16:9 displays a 4:3 picture at a 16:9 size; the picture is

stretched horizontally to ﬁll the screen.

Movie Expand displays a 4:3 picture at a 16:9 size; the

picture is stretched more vertically at the top of the

screen.This crops out the top of the picture.

Normal

16:9

Movie Expand

Zoom displays a 4:3 picture at a 16:9 size; at its

maximum size that is more vertically stretched to ﬁll

the screen.This crops out the top and bottom of the

picture.

Wide

Zoom

Wide displays the picture with its center at the original

size and the edges stretched horizontally to ﬁll the

screen.

Normal displays a proportionately stretched picture.

Sidebars appear on both edges of the screen.

HDMI1

For PC input signal through

Input mode

Full displays a picture that is stretched out of

proportion horizontally to ﬁll the screen.

Dot By Dot displays a picture in its original size.

Normal

Full

Dot By Dot

Channel Selection

Select channels by using CH+/− or the Number buttons.

•

To select the memorized channels, use CH+/− or the Number buttons.

To select the non-memorized channels, use the Number buttons.

11.1

To use the Number buttons

ATSC

NTSC

When selecting cable or analog channel 11

When selecting digital channel 11.1

Be sure to press • before entering the subchannel number.

Press PREV CH to return to the previously viewed channel.

• [No Signal] will appear on theTV screen after the subchannel broadcast is over.

• [Audio only program] message will appear on theTV screen, when you receive only sound signal.

Note

Download from Www.Somanuals.com. All Manuals Search And Download.

TV Screen Information

Reducing the Brightness

You can display the currently selected channel or other

information such as the audio mode on theTV screen.

In the digital mode, the detailed broadcasting information

for the current off the air channel such as program title and

program guides are displayed.

Backlight brightness can be reduced which may save on power

consumption more than you just set [On] in [Energy Saving

Mode]. p. 22

➠

Press ECO once to reduce the brightness.

Press ECO again to increase the brightness.

Press INFO.

Note

ATSC

• Even if this function is in effect, the brightness will be increased

when you change [Energy Saving Mode] on or off due to the

energy saving mode has priority.

• You must set [Home] in [Location]. p.23

Otherwise, the settings you adjusted will not be memorized after

the unit goes into standby mode.

➠

Day of Memories

KABC

11.1

English 1/2

quarter-century ago,which may now qualify as the

good old days of newspapering,run-of-paper sales

accounted for 80 percent of the industry's advertising

revenues.Department stores and supermarket were

1080i HD

16:9

6, 7, 8

Rating

TV: TV-14

fun-Link Options

NTSC

If you have our brand products such as BD player or DVD

recorder that are compatible with fun-Link functions, connect

them to this unit via an HDMI cable so you can simply operate

various items from this unit’s remote control.

SAP / STEREO

480i SD 4:3

Before you begin:

You must set [On] in [Device Control] and [fun-Link

6, 7, 8

TV-PG DLSV

Control]. p.22

➠

Otherwise,

OPTIONS does not work

even if you connected our brand devices to this unit.

program title

program guide

(The program guide added to broadcasting

To enjoy fun-Link, veriﬁed and recommended devices are as

follows;

information is displayed to a maximum of 4 lines.)

broadcast station

channel number

MAGNAVOX

MBP5230

MBP2100

MBP5120F

MBP5130

SYLVANIA

NB620SL2

NB620SL1

NB621SL1

MRD723B

MRD410B

audio language (ATSC)/audio mode (NTSC)

[Switching Audio Mode]

effective scanning lines and scan mode

TV format

p.12

➠

Press

[fun-Link Options] menu.

OPTIONS to display

program’s image aspect ratio

CC (not available if closed caption is set to [Off])

fun-Link Options

10 child lock rating

Device-menu

Device-contents

Device-favorite

Press INFO or BACK to hide the information.

Note

This function allows you to control the menu of

your connected fun-Link device.

• When the program guide consists of more than 4 lines, use ▲/▼

to scroll to the next/previous lines.

• [No description provided.] is displayed when the program guide

Device-menu

Device-

contents

This function allows you to control the top menu

of your DVD or Blu-ray discs.

is not provided.

• While the program guide is displayed, the closed caption function

is interrupted.

• In external input mode, the following screen is displayed;

e.g.) When an external device is connected toVideo Input jack.

Device-

favorite

This function allows you to control the pop-up

menu of your Blu-ray discs.

Use ▲/▼/OK on this unit’s remote control to operate

the desired functions for your devices.

Video

480i SD

TV-PG DLSV

Note

• The information display will automatically disappear in 1 minute.

• Some of fun-Link functions may not be available depending on

your fun-Link devices or discs.

• We do not guarantee 100% interoperability with other brands of

HDMI link compliant devices.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

USING FUNCTIONS

This section describes the overview of the main menu

displayed when you press MENU.

The main menu consists of the function setting items below.

Press MENU to display

the main menu.

Use ▲/▼ to select a desired menu and an item, then

press OK to determine the setting.

Picture

Page 16

Picture

Sound

Adjusting the picture mode, or customize the

picture quality as your preference.

Setup

Features

Language

Sound

Page 16

Adjusting the sound mode, equalizer and some

other sound functions.

Setup

Page 17

Scanning the channels available in your area and

see what the antenna levels are.

Features

Page 18

Adjusting the Closed Caption, parental guide and

some other useful functions.

Language

Page 23

You can choose English, Spanish, or French

as your on-screen language.

When the setting is completed, press MENU to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Picture

Sound

Before you begin:

You must set [Home] in [Location]. p.23

➠

Otherwise, the settings you adjusted will not be memorized

after the unit goes into standby mode.

Otherwise, the settings you adjusted will not be memorized

after the unit goes into standby mode.

Use ▲/▼ to select the item you want to adjust, then press

OK.

Use ▲/▼ to select the item you want to adjust, then press

OK.

Picture

Sound

Picture

Sound

Sound Mode

Picture Mode

Brightness

Contrast

Personal

Standard

Equalizer

Sound

Virtual Surround Sound

Auto Volume Leveling

TV Speakers

Color

Off

Setup

Tint

Ext. Amp

Stereo

Sharpness

Color Temperature

Primary MTS

Features

Language

Features

Language

Normal

Adjust the following items.

Picture Mode

Sound Mode

Use ▲/▼ to select the desired setting, then press OK.

([Personal], [Standard], [Movie], [Music], and [News])

Use ▲/▼ to select the desired setting, then press OK.

([Personal], [Standard], [Sports], [Movie], and [Game])

Brightness, Contrast, Color, Tint, Sharpness,

ColorTemperature

Equalizer

Adjust tonal quality for each frequency.

You can only adjust the following options when you set to

Use ◄/► to select the speciﬁc frequency and use ▲/▼ to

[Personal] in [Picture Mode].

adjust the level, then press OK.

Use ▲/▼ to select the desired setting, then press OK.Then

use ◄/► to adjust the setting.

Virtual Surround Sound

Virtual surround sound gives you the stereophonic virtual

space through your existing 2-channel stereo system.

Cursor ◄

Cursor ►

Brightness

Contrast

to decrease brightness to increase brightness

to decrease contrast

to increase contrast

to decrease color

intensity

to increase color

intensity

Use ▲/▼ to select the desired option, then press OK.

Color

Off

Emphasized effect.

Natural effect.

Tint

to add red

to soften

to add green

to sharpen

Sharpness

Color

Temperature

to add warm colors

to add cool colors

AutoVolume Leveling

This function keeps a constant loudness differential between

theTV commercials and the programs.

Use ▲/▼ to select the desired option, then press OK.

Reduces volume differences between the

TV commercials and the programs.

Off

Removes the auto volume leveling.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

TV Speakers

Autoprogram

Select the audio output from the unit’s speakers, or not. If your

ampliﬁer is HDMI link function compatible and connected by

an HDMI cable to this unit, some sound operations such as

volume up can be changed by using this unit’s remote control.

If you switch wires (e.g. between antenna and CATV) or if you

move the unit to a different area after the initial setting, or if

you restore the DTV channels you deleted, it is recommended

to use Autoprogram to perform a new channel search.

Make sure [fun-Link Control] is set to [On].

p.22

➠

Use ▲/▼ to select [Autoprogram], then press OK.

Use ▲/▼ to select an appropriate option, then press OK.

Autoprogram

Use ▲/▼ to select the desired option, then press OK.

The sound will be output from the unit’s speakers.

The sound will not be output from the unit’s

speakers.

Off

Picture

Sound

Back

Auto program will rescan all channels.

Auto programming may take more than 20

minutes to complete.

You can control audio output from your

connected HDMI link devices by using this unit's

remote control.

Antenna

Cable

Ext. Amp

Select your signal source.

Setup

Antenna

Note

Features

Language

• We do not guarantee 100% interoperability with other brands of

HDMI link compliant devices.

Cable

ANT.IN

• When connected toVHF/UHF antenna, select [Antenna].

• When connected to CATV, select [Cable].

• [Autoprogram] will begin.

Primary MTS

You can set the output mode as a default for the sound mode

(NTSC only).

This setting is not interlocked when you change the output

Please wait while the system is scanning for channels.

Auto programming may take more than 20 minutes to

complete.

mode by pressing SAP. [Sound Functions]

p.12

➠

Use ▲/▼ to select the desired option, then press OK.

75%

Stereo

Mono

SAP

Outputs stereo-audio.

Digital channels

Analog channels

10 ch

6 ch

Outputs mono-audio.

Outputs second audio program.

Exit

• When the scanning and memorizing are completed, the

lowest memorized channel will be displayed.

Setup

Note

Before you begin:

Make sure the unit is connected to antenna or cable.

• After setting [Autoprogram], using CH+/− on the remote control

skips unavailable programs automatically.

• If you are not receiving a signal from your cable service, contact

the Cable provider.

• If you press or MENU during autoprogram, the setup ofTV

Use ▲/▼ to select the item you want to adjust, then press

OK.

channels will be canceled.

• Even if [Autoprogram] is completed, the channel setting will be

lost if the AC power cord is unplugged before the unit goes into

Setup

standby mode by pressing

• The PIN code will be required once you set a PIN code in the

[Child Lock]. p.20

Picture

Sound

Autoprogram

Channel List

Add Channels

Antenna

➠

• If you want to change your PIN code, follow the instruction of

[Change PIN]. p.21

Setup

➠

Features

Language

Adjust the following items.

Download from Www.Somanuals.com. All Manuals Search And Download.

Channel List

The channels selected here can be skipped when selecting the

Antenna Conﬁrmation

ATSC

channels using CH+/−.

Those channels can still be selected with the Number buttons.

This function lets you check the digital signal strength of each

channel.

Use ▲/▼ to select [Channel List], then press OK.

Use ▲/▼ to select [Antenna], then press OK.

Use ▲/▼ to select the channel you want to remove, then

press OK.

Use the Number buttons or CH+/− to select the channel

for which you want to check the digital signal strength.

Channel List

11.1

Picture

DTV

6.1

8.1

Highlight channels for

Ch Up / Down key selection.

Antenna

Sound

Picture

Sound

Back

Setup

DTV

48.1

Features

Language

67.1

Setup

Current 50 Max

Ch Select

Watch/Skip

Back

Features

Language

• The channel display for the removed channel darkens.

You will not be able to select the channel again using

CH+/−.

Ch Change

• To reactivate a removed channel, use ▲/▼ and press

OK.The registered channels are highlighted.

Note

• If the channel is set to analog channel or external input, you

cannot conﬁrm the antenna condition.

• When you remove a main channel, its subchannels are

removed as well.

Note

• The channel with the [DTV] indicated on the display is ATSC.

Otherwise the channel is NTSC.

Features

Use ▲/▼ to select the item you want to adjust, then press

OK.

Add Channels

This function lets you add the off the air along NTSC or analog

Cable channels that were not added by the autoprogram due

to reception conditions at the initial setting.

Features

Picture

Closed Caption

Child Lock

Sound

fun-Link (HDMI CEC)

Use ▲/▼ to select [Add Channels], then press OK.

Energy Saving Mode

Location

Setup

Home

Use the Number buttons to enter the number of the

channel you want to add, then press OK.

Current Software Info

Features

Language

Add Channels

Adjust the following items.

Picture

Sound

Add Channels

For analog channels, select a

channel to be added using

number keys.

Closed Caption

Setup

For digital channels, you must

perform Autoprogram function.

You can view closed captioning (CC) forTV programs,

movies and news. Closed caption refers to text of dialog or

descriptions displayed on-screen.

Features

Language

Ch Change

Back

Use ▲/▼ to select [Closed Caption], then press OK.

See the following description for setting each item.

Note

• If setup completes successfully, [Added to the channel list.] is

displayed.

• If external input is used, it is not possible to register the channel

and [Unavailable] will be displayed on theTV screen.

• By using CH+/−, you can select the memorized channels only.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

C. Captioon Style

ATSC

Closed Caption

Picture

Sound

Caption Service

Digital Caption Service

Caption Style

Off

You can change the caption style such as font, color or size,

etc.

Setup

Features

Language

Use ▲/▼ to select [Caption Style], then press OK.

Use ▲/▼ to select [User Setting], then press OK.

Use ▲/▼ to select [On], then press OK.

Use ▲/▼ to select an item, then press OK. Then use

▲/▼ to select the desired setting and press OK.

A. Captionn Service

Use ▲/▼ to select [Caption Service], then press OK.

Picture display

Use ▲/▼ to select the desired closed caption, then press

OK.

So, you must be Philip. Hi!

I’m pleaseed to meet you.

Off

Select if you do not want caption service.

The primary caption and text services.The

captioning or text is displayed in the same language

Edge

CC-1 andT-1 as the program’s dialog (up to 4 lines of script on the

TV screen, where it does not obstruct relevant parts

of the picture).

(Edge Color and EdgeType)

Font

(Font Style, Font Size, Font Color and Font Opacity or

Transparency)

Serve as the preferred data channels.

CC-3 andT-3 The captioning or text is often a secondary

language.

Background

(Background Color and Background Opacity or

Transparency)

Rarely available and broadcasters use them only in

CC-2, CC-4,

special conditions, such as when [CC-1] and [CC-3]

T-2 andT-4

or [T-1] and [T-3] are not available.

• Review your setting choice made below by looking in

the upper right corner of the displayed setting box (not

all selections show the differences selected).

• There are 3 display modes according to programs:

Paint-on

mode

Displays input characters on theTV screen

immediately.

Font Style

Font Size

Once characters are stored in memory, they are

displayed all at once.

Closed captioning font style, size,

color and opacity can be changed.

Pop-on mode

Roll-up mode

Font

Font Color

Displays the characters continuously by scrolling

(max. 4 lines).

Font

Opacity

Background

Color

Background color and opacity of the

displayed caption can be switched.

Background

Opacity

B. Digiital Capption SSeervice

ATSC

Edge Color

EdgeType

Edge color and type of the displayed

caption can be switched.

Edge

In addition to the basic closed caption, DTV has its own closed

caption called digital caption service. Use this menu to change

the settings for digital caption service.

Use ▲/▼ to select [Digital Caption Service], then press

OK.

Use ▲/▼ to select the desired digital caption service, then

press OK.

Select if you do not want digital caption

service.

Off

Select one of these before changing any

CS-1 to CS-6

other item in [Closed Caption] menu.

Choose [CS-1] under normal circumstances.

Note

• [Digital Caption Service] that you can switch differs depending on

the broadcast description.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

Child Lock

• Closed caption will not be displayed when you are using an HDMI

connection.

• To show the closed caption on yourTV screen, broadcast signal

must contain the closed caption data.

• Not allTV programs and commercials have the closed caption or

all types of the closed caption.

• Captions and texts may not exactly match theTV voice.

• Changing channels may delay the closed caption for a few seconds.

• Adjusting or muting the volume may delay the closed caption for

a few seconds.

Picture

Sound

Channel Lock

US Movie Ratings Lock

US TV Ratings Lock

Canadian English Rating

Canadian French Rating

Region Ratings Lock

Clear Region Ratings Lock

Change PIN

Setup

Features

Language

• Abbreviations, symbols and other grammatical shortcuts may be

used in order to keep pace with the on-screen action.This is not

a malfunction.

• The caption or text characters will not be displayed while the

main menu or functions display is shown.

• If a black box appears on theTV screen, this means that the closed

caption is set to the text mode.To clear the box, select [CC-1],

[CC-2], [CC-3], [CC-4] or [Off].

Note

• When you select a rating and set it to [Block], the higher ratings

will be blocked automatically.The lower ratings will be available for

viewing.

• When you set the highest rating to [View], all ratings turn to

[View] automatically.

• To block any inappropriate programs, set your limits in [US Movie

Ratings Lock], [USTV Ratings Lock] and [Region Ratings Lock].

• The child lock setting will be retained after a power failure or after

the power is removed for longer than 10 seconds (except the PIN

• If the unit receives poor quality television signals, the captions may

contain errors, or there might be no captions at all. Some possible

causes of poor quality signals are:

- Automobile ignition noise

- Electric motor noise

code reverts to 0000). [Child Lock]

p.20

➠

• If the rating is blocked, will appear.

- Weak signal reception

• [Region Ratings Lock] will be available when the unit receives a

digital broadcast using the new rating system.

• For the United States, the unit may download the Region Ratings

LockTable, if required.

• The Canadian rating systems on this unit are based on CEA-766-A

and CRTC policy.

- Multiplex signal reception (ghosts or screen ﬂutter)

- Data dropout and Pixelation (for DTV only)

• The unit retains the closed caption setting if the power fails.

• When the unit receives special effects playback signal (e.g. Search,

Slow and Still) from aVCR’s video output channel (ch3 or ch4),

the unit may not display the correct caption or text.

A. Channnel Lock

Particular channels or external input modes can be invisible in

this function.

Child Lock

Child lock reads the ratings for programs, then denies access

to the programs which exceed the rating level you set.With

this function, you can block certain programs inappropriate

for children and any channels or external input modes can be

invisible.

Use ▲/▼ to select [Channel Lock], then press OK.

Use ▲/▼ to select the desired rating, then press OK

repeatedly to switch between [View] and [Block].

Use ▲/▼ to select [Child Lock], then press OK.

Features

Channel Lock

Picture

Sound

Closed Caption

Child Lock

Picture

Sound

Video

Component

HDMI1

fun-Link (HDMI CEC)

Energy Saving Mode

Location

HDMI2

Setup

Home

HDMI3

Current Software Info

40.1 DTV

40.2 DTV

Features

Language

Features

Language

Select

View/Block

Back

Use the Number buttons to enter the 4-digit numbers for

your PIN code.

B. Settting US MMovie rraatings

US Movie ratings lock is the rating system created by MPAA.

Setup

Enter PIN.

- - - -

Features

Use ▲/▼ to select [US Movie Ratings Lock], then press

OK.

• When you have not set up your PIN code,

enter 0, 0, 0, 0.

• When the PIN code is correct, [Child Lock] menu is

displayed.

See the following description for setting each item.

Use ▲/▼ to select the desired rating, then press OK

repeatedly to switch between [View] and [Block].

Download from Www.Somanuals.com. All Manuals Search And Download.

English

US Movie Ratings Lock

US TV Ratings Lock

Picture

Sound

Picture

Sound

NC-17

TV-MA

TV-14

TV-PG

TV-G

PG-13

Setup

Features

Language

Features

Language

TV-Y7

TV-Y

Select

View/Block

Back

Select

View/Block

Back

Sub Rating

Category

Enter PIN.

- - - -

Mature audience only

higher

Setup

Confirm PIN.

- - - -

TV-14

TV-PG

TV-G

Unsuitable for children under 14

Parental guidance suggested

General audience

Features

Language

PIN Code

Back

Appropriate for all children 7 and

older

TV-Y7

TV-Y

Note

• Make sure new PIN code and conﬁrm PIN code must be exactly

the same. If they are different, the space is cleared for reentering.

• Your PIN code will be erased and returns to the default PIN code

(0000) when a power failure occurs.

• If you forget the PIN code, unplug the AC power cord then wait

for 10 seconds to plug the AC power cord in again.

Appropriate for all children

lower

To set the sub ratings

As forTV-MA,TV-14,TV-PG, orTV-Y7, you can further set the

sub ratings to block speciﬁc elements of programming.To set

the sub ratings, follow the step below.

The unit will restore the PIN code to 0000 as the factory default.

Use ▲/▼/◄/► to select the desired rating, then press OK

repeatedly to switch between [View] and [Block].

Download from Www.Somanuals.com. All Manuals Search And Download.

Device Control

fun-Link (HDMI CEC)

You can operate some functions such as disc playback or call

up the menu of the connected devices, by using this unit’s

remote control.

This function allows you to operate the linked functions

between our brand devices with a fun-Link feature and this

unit connecting through an HDMI cable.

Use ▲/▼ to select the desired setting, then press OK.

Use ▲/▼ to select [fun-Link (HDMI CEC)], then press

OK.

B /C /D /E /G /H /F /

OPTIONS/

▲/▼/◄/►/OK/BACK/the Number buttons/

RED/GREEN/BLUE/YELLOW can be used to

fun-Link (HDMI CEC)

control your connected fun-Link devices by this

unit’s remote control.

Picture

Sound

fun-Link Control

Auto Device Off

Auto TV On

Off

Disables the device control.

Device Control

Device List

Setup

Device List

Features

Language

This function lets you see the product model number or name

of connected devices.

Use ▲/▼ to select the desired HDMI device listed on theTV

screen, then press OK.

Use ▲/▼ to select the desired setting, then press OK.

Device List

Adjust the following items.

Picture

HDMI1

NB620SL2

MBP5230

MRD723B

HDMI2

HDMI3

Sound

fun-Link Control

Set the fun-Link [On] or [Off].

The following additional settings will be grayed out when you

set to [Off].

Setup

Features

Language

Use ▲/▼ to select the desired setting, then press OK.

Select

Input Change

Back

Selects if you have connected an external device

that is compatible with the fun-Link function.

Off

Disables all fun-Link.

Energy Saving Mode

Auto Device Off

You can set your device to turn off by interlocking from this

unit’s power.

You can turn on Energy Saving Mode to conserve power.

Energy Saving Mode: ON is ENERGY STAR^®qualiﬁed setting.

Use ▲/▼ to select [Energy Saving Mode], then press OK.

Use ▲/▼ to select the desired mode, then press OK.

Reduces power consumption

Use ▲/▼ to select the desired setting, then press OK.

Your connected fun-Link device turns off

Off

automatically when the unit goes into standby

mode.

Power consumption may exceed ENERGY STAR^®

qualification limits.

Your connected fun-Link device stays on even if

the unit goes into standby mode.

Off

Note

AutoTV On

• You must set [Home] in [Location]. p.23

Otherwise, the settings you adjusted will not be saved when the

unit goes into standby mode.

➠

This unit will turn on when the power on signal is sent from

your connected fun-Link device.

• You can also press ECO directly to switch the desired setting.

Use ▲/▼ to select the desired setting, then press OK.

p.14

➠

This unit turns on automatically when you turn on

your connected fun-Link device.

This unit stays in standby mode even if you turn on

your connected fun-Link device.

Off

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Location

When you select [Retail] store, the power consumption may

possibly exceed the limited requirement of the

ENERGY STAR^®qualiﬁcation.

Use ▲/▼ to select [Location], then press OK.

Use ▲/▼ to select the desired location, then press OK.

The unit will be set up with predefined settings

for retail displays. In this setting, the power

Retail

consumption may possibly exceed the limit

requirement of the ENERGY STAR^®qualification.

This setting is ENERGY STAR^®qualified.

The unit is set to maximize the energy efficiency

for home setting and it can be adjusted through a

choice of picture and sound quality according to

your preference.

Home

Current Software Info

This function shows what version of the software currently

used.

Use ▲/▼ to select [Current Software Info], then press

OK.

Conﬁrm the version of the software currently used.

Current Software Info

Picture

Sound

Back

Release Version:

XXXXXXX_XXX_X_XXXX

Setup

Features

Language

Use ▲/▼ to select [English], [Español] or [Français], then

press OK.

Language

Picture

Select your menu language.

English

Sound

Seleccione el idioma para el menú.

Sélectionnez la langue du menu.

Español

Setup

Français

Features

Language

Note

• If you need the English menus instead of the Spanish or French

menus, press MENU. Use ▲/▼ to select [Idioma] or [Langue],

then press OK.

Use ▲/▼ to select [English], then press OK.

Press MENU to exit the main menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

CONNECTING

DEVICES

No supplied cables are used with these connections:

• Please purchase the necessary cables at your local store.

• Use an HDMI cable with the HDMI logo (a certiﬁed HDMI cable).

High Speed HDMI cable is recommended for the better compatibility.

For HDMI connection (use HDMI 1, 2 or 3 Input jack)

• The unit accepts 480i, 480p, 720p, 1080i and 1080p 24/30/60Hz

of video signals, and 32kHz, 44.1kHz and 48kHz of audio signals.

• This unit accepts 5.1 channel audio signal (Dolby Digital) and 2

channel audio signal (LPCM).

• This unit accepts only signals in compliance with EIA861.

Before you connect:

Be sure other device is connected properly before plugging in

the AC power cord.

For HDMI-DVI connection

• The unit accepts 480i, 480p, 720p, 1080i and 1080p video signals.

• HDMI-DVI connection requires separate audio connections as

well and the audio signals are converted from digital to analog.

• DVI does not display 480i image which is not in compliance with

EIA/CEA-861/861B.

External Device Connection

HDMI Connection

HDMI connection offers the highest picture quality.

HDMI (High-Deﬁnition Multimedia Interface) transports high deﬁnition

digital video and multi-channel digital audio through a single cable.

ComponentVideo Connection

ComponentVideo connection offers better picture quality for

video devices connected to the unit.

If you connect to the unit’s ComponentVideo Input jacks,

connect Analog Audio cables to the Analog Audio L/R Input

jacks right beside the ComponentVideo connector jacks.

BD/DVD recorder

with the component video output jacks

HDMI cable

TITLE

CHAPTER 15

REPEAT A-B

COMPONENT VIDEO OUT

AUDIO OUT

Pb/Cb

Pr/Cr

(green) (blue) (red)

HDMI OUT

component video cables

(red/blue/green)

TITLE

CHAPTER 15

REPEAT A-B

audio cables

BD/DVD recorder

with the HDMI output jack

Note

• The unit accepts 480i/480p/720p and 1080i of video signals for

this connection.

HDMI-DVI Connection

Use an HDMI-DVI conversion cable to connect the unit to

external video devices equipped with DVI output jack.

(use HDMI 1 Input jack only and Audio L/R beside HDMI 1

jack on rear of TV)

S-Video Connection

S-Video connection offers good picture quality for video

devices connected to the unit.

If you connect to the unit’s S-Video Input jack, connect audio

cables to the Audio L/R input jacks right above the Composite

Video connector.

To HDMI 1 Input

jack only

cable receiver or satellite box

with the DVI output jack

STEREO

PCM

BD/DVD recorder, camcorder and

VCR with the S-Video output jack

TITLE

CHAPTER 15

REPEAT A-B

AUDIO OUT

DVI OUT

S-VIDEO

OUT

AUDIO OUT

HDMI-DVI

conversion cable

audio cables

S-Video cable

Download from Www.Somanuals.com. All Manuals Search And Download.

English

CompositeVideo Connection

Analog Audio Output Connection

CompositeVideo connection offers standard picture quality

for video devices connected to the unit. If you connect to the

unit’s Composite video Input jack, connect audio cables to

the Audio L/R input jacks right above the Composite video

connector.When the Audio is monaural, then only connect to

the Audio L Input jack.

(for both analog and digital broadcasting)

If you connect this unit to an external analog audio device, you

can enjoy stereo (2-channel) audio.

Use audio cables to connect the unit to external analog audio

devices.

stereo system

camcorder

VCR

video game

AUDIO IN

STAND-BY

STEREO

VIDEO

OUT

AUDIO OUT

audio cables

PC Connection

This unit can be connected to your PC that has a DVI terminal.

Use an HDMI-DVI conversion cable for thisVideo connection

and it requires stereo mini plug conversion cable for Analog

Audio signal as well.

video cable

If you connect this unit to your PC, you can use this unit as a

PC monitor.

Digital Audio Output Connection

(for digital broadcasting only)

If you connect this unit to an external digital audio device, you

can enjoy multi-channel audio like 5.1ch digital broadcasting

sound.

Use a digital audio coaxial cable to connect the unit to

external digital audio devices.

personal computer

To HDMI 1 Input

jack only

DVI OUT

audio cables

Dolby Digital

decoder

DIGITAL AUDIO

COAXIAL IN

HDMI-DVI conversion

cable should be with

ferrite core.

mini audio

cable

HDMI-DVI conversion cable

digital audio coaxial cable

The following video signals can be displayed:

Format

VGA

Resolution

Refresh rate

640

480

SVGA

XGA

800

1,024

1,280

1,360

600

768

60Hz

WXGA

Other formats or non-standard signals will not be displayed

correctly.

Note

• Please purchase the HDMI-DVI conversion cable that has a ferrite

core.

• The following operations may reduce noise.

- Attach a ferrite core to the AC power cord of your PC.

- Unplug the AC power cord and use the built-in battery of your

PC.

Download from Www.Somanuals.com. All Manuals Search And Download.

USEFULTIPS

FAQ

Question

Answer

•

Check the antenna or cable connection to the main unit.

•

Check the batteries of the remote control.

Check if there is an obstacle between the infrared sensor window and the remote control.

Test the signal output use [IR Signal Check].

If okay, then possible infrared sensor trouble.

p.28

➠

My remote control does not work.

What should I do?

•

Aim the remote control directly at the infrared sensor window on the front of the unit.

Reduce the distance to the unit.

Re-insert the batteries with their polarities (+/– signs) as indicated.

When there is an infrared-equipped device such as PC near this unit, it may interrupt the remote

control signal of this unit.

•

Move the infrared-equipped device away from this unit, change the angle of the infrared sensor or

turn off the infrared communication function.

How come the Initial setup

appears every time I turn on this

unit?

•

Connect the RF coaxial cable to the unit directly and run the initial setup.

Make sure to complete the channel scan before the unit goes into standby mode.

•

Make sure [Autoprogram] has been completed.

Autoprogram must be completed when you set up the unit for the ﬁrst time or move it to a location

where previously unavailable channels are broadcast.

p.17

➠

•

The selected channel may not be broadcasting.

Why can I not watch some RF

signalTV programs.

When [Autoprogram] is interrupted and not completed, some channels will not be received. Make

sure to complete the Autoprogram.

The selected channel cannot be viewed by the [Child Lock] setting.

p.17

➠

•

p.20

➠

The unit requires some kind of antenna input.An indoor antenna (VHF/UHF), an external antenna

(VHF/UHF) or an RF coaxial cable from your wall cable/satellite box needs to be plugged into the unit.

•

Check if the correct input mode is selected by pressing SOURCE or using CH+/−. [Switching Each

Input Mode]

p.13

➠

How come there is no image from

the connected external devices?

•

Check the antenna or cable connection to the unit.

When using the ComponentVideo Connection check that the Green (Y), Blue (Pb/Cb) and Red (Pr/

Cr) connectors are connected to their corresponding colored jacks on the unit.

•

Many digital channels have alternate channel numbers.The unit changes the numbers automatically to

the ones signifying the broadcasting station channel number.These basic numbers used for previous

analog broadcasts. (e.g., input ch#30 auto changes to ch#6.1)

When I enter a channel number, it

changes automatically.

Captions that are delayed a few seconds behind the actual dialog are common for live broadcasts.

Most captioning production companies can display a dialog to maximum of 220 words per minute. If

a dialog exceeds that rate, selective editing is used to insure that the captions remain up-to date with

the currentTV screen dialog.

Why are captions not displayed

entirely? Or, captions are delayed

behind the dialog.

How can I set the clock ?

•

There is no clock function on this unit.

I cannot change the [Child Lock]

setting because my PIN code no

longer works.

If a Power failure occurs for longer than 10 seconds the child lock setting is retained, but the PIN code

is set to the default code “0000”. [Child Lock]

p.20

➠

Troubleshooting Guide

If the unit does not perform properly when operated as instructed in this manual,

check the following chart and all connections once before calling for service.

Symptom

Remedy

•

Make sure the AC power cord is plugged in.

•

Make sure that the AC outlet supplies the proper voltage, plug another electrical appliance into the

AC outlet to ensure that AC outlet operates normally.

No power

•

If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit to reset itself.

•

Press only one button at a time. Do NOT press more than one button at the same time.

Ensure that no buttons on the remote control are depressed and move freely.

Control button's do not work.

•

Check whether the connection of the antenna, cable receiver or satellite box is connected correctly.

Check whether all the cables to the unit are connected to the correct output jack of your device like

BD/DVD recorder.

Power is ON but no screen image.

•

Make sure that the selected input mode is connected to the working input jack.

Check if your computer is NOT in sleep mode when the input mode of this unit is in PC mode.Tap

any key on the keyboard to wake up your computer.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Symptom

Remedy

•

Check if the power is on.

•

Check if the correct input mode is selected.

Check whether all the cables to the unit are connected to the correct output jack of your device like

BD/DVD recorder.

•

View otherTV channels.The problem might be limited to the broadcasting station or weak signal

strength.

Unplug the AC power cord and wait for about 1 minute, then plug the AC power cord and turn on

the unit again.

No picture or sound

•

Check whether the connection of the antenna, cable receiver or satellite box is connected correctly.

Make sure that the selected input mode is connected to the working input jack.

Check if your computer is NOT in sleep mode when the input mode of this unit is in PC mode.Tap

any key on the keyboard to wake up your computer.

•

Make sure that the sound is not muted. Press MUTE

so that the volume bar and current volume

level will appear on theTV screen.

Make sure that the volume is NOT set to [ ] or [Mute]. If so, use VOL +/− to adjust the desired

volume.

•

View otherTV channels.The problem might be limited to the broadcasting station or weak signal

strength.

Adjust [Color] in the main menu.

No color

Adjusted [Picture] or [Sound]

settings are not effective every time

the unit is turned on.

•

You must set [Home] in [Location]. p.23

➠

Otherwise, the settings you adjusted will not be memorized after the unit goes into standby mode.

•

Electrical interference from nearby appliances may affect picture quality.

Adjust [Contrast] and [Brightness] in the main menu.

View otherTV channels.The problem might be limited to the broadcasting station or weak signal

strength.

For the best picture quality, watch "High Definition" wide screen programs.

If the HD content is not available, watch "Standard Definition" programs instead.

Sound OK, picture poor

Picture OK, sound poor

•

View otherTV channels.The problem might be limited to the broadcasting station or weak signal

strength.

•

Check if the audio cable is connected in correctly.

You may be getting interference from electrical appliances, automobiles, motorcycles or ﬂuorescent

lights.

Try moving the unit to another location to see if this is the cause of the problem.

You see a distorted picture or hear

an unusual sound.

•

Electrical interference from nearby appliances may affect picture quality.

View otherTV channels.The problem might be limited to the broadcasting station or weak signal

strength.

Ghosts, lines or streaks in picture

You see "noise" or "trash" on the

•

When the capabilities of the unit exceed the capabilities of the digital broadcasting, the signal will be

increased to match the capabilities of the display of the unit.This may cause noise or trash.

screen.

Different color marks on theTV

screen

View otherTV channels.The problem might be limited to the broadcasting station, missing data or

pixelation.

•

This unit will memorize the volume level from the last time you adjusted it.

If the volume of the sound from another device is higher or lower, then the loudness will change.

You switch to a different input and

the volume changes.

You switch to a different input and

the screen size changes.

•

This unit will memorize the viewing mode from the last time you used the particular input modes.

If you are watchingTV or using the CompositeVideo, ComponentVideo or HDMI with 480i Input,

The display image does not cover

the entire screen.

press FORMAT

repeatedly to switch various screen modes.

Captions are displayed as a white

box. No caption is displayed in

the Closed Caption-supported

program.

•

Interference from buildings or weather conditions may cause captioning to be incomplete.

Broadcasting station may shorten the program to insert advertisement.

The closed caption decoder cannot read the information of the shortened program.

Black box is displayed on theTV

screen.

•

The text mode is selected for caption. Select [CC-1], [CC-2], [CC-3], [CC-4] or [Off].

Note

• The LCD screen is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a ﬁxed point of blue,

green or red.

This is not to be considered a defect in the LCD screen.

• Some functions are not available in speciﬁc modes, but this is not a malfunction. Read the description in this manual for more details on

correct operations.

Download from Www.Somanuals.com. All Manuals Search And Download.

INFORMATION

Glossary

Maintenance

ATSC

Cabinet Cleaning

Wipe the front panel and other exterior surfaces of the

unit with a soft cloth.

Never use a solvent or alcohol. Do not spray insecticide

liquid near the unit. Such chemicals may cause damage and

discoloration to the exposed surfaces.

Acronym that stands for AdvancedTelevision Systems Committee and

the name of the digital broadcasting standards.

•

Aspect Ratio

The width of aTV screen relative to its height. ConventionalTVs

are 4:3 (in other words, theTV screen is almost square); widescreen

models are 16:9 (theTV screen is almost twice as wide as its height).

CEC (Consumer Electronics Control)

This allows you to operate the linked functions between our brand

devices with CEC feature and this unit.We do not guarantee 100%

interoperability with other brands of CEC compliant devices.

Panel Cleaning

Wipe the panel of the unit with a soft cloth. Before cleaning

the panel, disconnect the AC power cord.

ComponentVideo

This is a video signal format that conveys each of 3 principal colors

of light (red, blue and green) through different signal lines.This allows

the viewers to experience picture colors as original as it is.There are

several signal formats, includingY/Pb/Pr andY/Cb/Cr.

Servicing

Dolby Digital

The system developed by Dolby Laboratories to compress digital

sound. It offers stereo sound (2ch) or multi-channel audio.

Should your unit become inoperative, do not try to correct

the problem yourself.There are no user serviceable parts

inside. Call our toll free customer support line found on the

cover of this manual to locate an authorized service center.

HDMI (High-Definition Multimedia Interface)

Interface that supports all uncompressed, digital audio/video formats

including set-top box, BD/DVD recorder or digital television, over a

single cable.

HDTV (High DefinitionTV)

IR Signal Check

If the remote control is not working properly, you can use a

digital camera (including a cellular phone with built-in camera)

to see if it is sending out an infrared signal.

Ultimate digital format that produces high resolution and high picture

quality.

NTSC

Acronym that stands for NationalTelevision Systems Committee and

the name of analog broadcasting standards.

Off the air NTSC signals are no longer being sent by major

broadcasting stations in the USA.

With a digital camera

PIN code

(including built-in cell phone cameras):

Point the Digital Camera towards the remote

control infrared diode at the front of the

remote control. Press any button on the

remote control and look through the camera

display. If the infrared pulsating light appears

through the camera, the remote control is

sending out an IR signal.

A stored 4-digit number that allows access to parental control features.

SAP (Secondary Audio Program)

Second-audio channel delivered separately from main-audio channel.

This audio channel is used as an alternate in bilingual broadcasting.

SDTV (Standard DefinitionTV)

Standard digital format that is similar to the NTSC picture quality.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

General Speciﬁcations

Other Speciﬁcations

TV format

Closed Caption system

ATSC/NTSC-MTV standard

Terminals

Antenna Input VHF/UHF/CATV

75Ω unbalanced (F-type)

500mV rms

§15.122/FCC (digital CC)

§15.119/FCC (analog CC)

Channel coverage (ATSC/NTSC)

Terrestrial DTV (ATSC)

VHF 2~13

Audio Input

CompositeVideo Input

RCA jack x 1

RCA jack (L/R) x 6

1V p-p (75Ω)

S-Video Input Mini DIN 4pin jack x 1

1V p-p(75Ω)

286mV p-p(75Ω)

UHF 14~51 (each channel has e.g.

ComponentVideo Input

2.1~2.9, 3.1~3.9, etc.)

RCA jack x 3

1V p-p(75Ω)

Terrestrial Analog (NTSC)

VHF 2~13

Pb/Cb 700mV p-p(75Ω)

Pr/Cr 700mV p-p(75Ω)

UHF 14~69

2~13,A~W,

HDMI Input

HDMI 19pin x 3

CATV

W+1~W+94 (analog W+1~W+84),

Digital Audio Output (coaxial)

RCA jack x 1

A-5~A-1, 5A

500mV p-p (75Ω)

Tuning system

Channel access

Channel frequency synthesized tuning

system

Direct access keyboard,

Programmable scan, and up/down

Analog Audio Output

RCA jack (L/R) x 2

500 mV rms

Remote control

Digital encoded infrared light system

Operating temperature

Electrical Speciﬁcation

41°F (5°C) to 104°F (40°C)

Power requirements

Audio Output

10W, 8Ω x 2

120V~ AC +/− 10%, 60Hz +/− 0.5%

Power consumption (maximum)

110W

26inches

LCD

Dimensions

Width 25.9 inches (656.0mm) 25.9 inches (656.0mm)

Height 17.7 inches (448.0mm) 19.2 inches (487.0mm)

Depth 3.9 inches (99.0mm)

14.89 lbs. (6.75kg)

9.3 inches (234.0mm)

15.88 lbs. (7.20kg)

Weight

•

Designs and speciﬁcations are subject to change without

notice and without our legal obligation.

If there is a discrepancy between languages, the default

language will be English.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

LIMITED WARRANTY

( )

(

)

NINETY 90 DAY LABOR / ONE 1 YEAR PARTS

WARRANTY COVERAGE:

This warranty obligation is limited to the terms as set forth

below.

mission, or (d) if any serial number has been removed or defaced,

or (e) product, accessories or consumables sold “AS IS” without

warranty of any kind by including refurbished product sold “AS

IS” by some retailers.

WHO IS COVERED:

This product warranty is issued to the original purchaser or the

person receiving the product as a gift against defects in materials

and workmanship as based on the date of original purchase

(“Warranty Period”) from an Authorized Dealer. The original

sales receipt showing the product name and the purchase date

from an authorized retailer is considered such proof.

This Limited Warranty does not cover:

•

Shipping charges to return defective product.

Labor charges for installation or setup of the product, adjust-

ment of customer controls on the product, and installation or

repair of antenna/signal source systems outside of the product.

Product repair and/or part replacement because of improper

installation or maintenance, connections to improper voltage

supply, power line surge, lightning damage, retained images or

•

WHAT IS COVERED:

This warranty covers new products if a defect in material or

workmanship occurs and a valid claim is received within the

Warranty Period. At its option, the company will either (1)

repair the product at no charge, using new or refurbished

replacement parts, or (2) exchange the product with a product

that is new or which has been manufactured from new, or ser-

viceable used parts and is at least functionally equivalent or most

comparable to the original product in current inventory, or (3)

refund the original purchase price of the product.

tent for extended periods, product cosmetic appearance items

due to normal wear and tear, unauthorized repair or other

cause not within the control of the company.

Damage or claims for products not being available for use, or

for lost data or lost software.

Damage from mishandled shipments or transit accidents when

returning product.

•

Replacement products or parts provided under this warranty are

covered against defects in materials and workmanship from the

date of the replacement or repair for ninety (90) days or for the

remaining portion of the original product’s warranty, whichever

provides longer coverage for you. When a product or part is

exchanged, any replacement item becomes your property and the

replaced item becomes company property. When a refund is

given, your product becomes company property.

it to operate in any country other than the country for which

it was designed, manufactured, approved and/or authorized, or

•

A product used for commercial or institutional purposes

(including but not limited to rental purposes).

can be provided.

Failure to operate per Owner’s Manual.

Note: Any product sold and identified as refurbished or

renewed carries a ninety (90) day limited warranty.

TO OBTAIN ASSISTANCE…

Contact the Customer Care Center at:

1-866-321-3927

Replacement product can only be sent if all warranty

requirements are met. Failure to follow all requirements

can result in delay.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CON-

SUMER, WITH THE ISSUING COMPANY NOT LIABLE FOR

ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON

THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY

APPLICABLE LAW, ANY IMPLIED WARRANTY OF MER-

CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

ON THIS PRODUCT IS LIMITED IN DURATION TO THE

DURATION OF THIS WARRANTY.

WHAT IS NOT COVERED - EXCLUSIONS AND LIMI-

TATIONS:

This Limited Warranty applies only to new company manufac-

to any hardware product or any software, even if packaged or

sold with the product, as manufacturers, suppliers, or publishers

may provide a separate warranty for their own products pack-

aged with the bundled product.

The company is not liable for any damage to or loss of any pro-

grams, data, or other information stored on any media contained

within the product, or other additional product or part not cov-

ered by this warranty. Recovery or reinstallation of programs,

data or other information is not covered under this Limited

Warranty.

Some states do not allow the exclusions or limitation of inciden-

tal or consequential damages, or allow limitations on how long an

implied warranty lasts, so the above limitations or exclusions may

not apply to you.

This warranty does not apply (a) to damage caused by accident,

abuse, misuse, neglect, misapplication, or non-supplied product,

(b) to damage caused by service performed by anyone other than

company approved Authorized Service Location, (c) to a product

FUNAI CORPORATION, Inc. 19900 Van Ness Avenue, Torrance, CA 90501

Printed in China

Download from Www.Somanuals.com. All Manuals Search And Download.

TERMS AND CONDITIONS FOR COPYING,

DISTRIBUTION AND MODIFICATION

License

This section describes software license used for this product.

0. This License applies to any program or other work which

contains a notice placed by the copyright holder saying it may

be distributed under the terms of this General Public License.

The “Program”, below, refers to any such program or work,

and a“work based on the Program”means either the Program

or any derivative work under copyright law: that is to say, a

work containing the Program or a portion of it,either verbatim

or with modiﬁcations and/or translated into another language.

(Hereinafter, translation is included without limitation in the

term “modiﬁcation”.) Each licensee is addressed as “you”.

This product uses some open source software:

GPL software: liba52.c, scalfact.c

jpeglib.h

FreeType

GPL

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Activities other than copying, distribution and modiﬁcation are

not covered by this License; they are outside its scope.The act

of running the Program is not restricted, and the output from

the Program is covered only if its contents constitute a work

based on the Program (independent of having been made by

running the Program).Whether that is true depends on what

the Program does.

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

Everyone is permitted to copy and distribute verbatim copies of

this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your

freedom to share and change it. By contrast, the GNU General

Public License is intended to guarantee your freedom to share

and change free software--to make sure the software is free for

all its users. This General Public License applies to most of the

Free Software Foundation’s software and to any other program

whose authors commit to using it. (Some other Free Software

Foundation software is covered by the GNU Lesser General

Public License instead.)You can apply it to your programs, too.

1. You may copy and distribute verbatim copies of the Program’s

source code as you receive it, in any medium, provided that

you conspicuously and appropriately publish on each copy

an appropriate copyright notice and disclaimer of warranty;

keep intact all the notices that refer to this License and to the

absence of any warranty; and give any other recipients of the

Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a

copy, and you may at your option offer warranty protection in

exchange for a fee.

When we speak of free software, we are referring to freedom,

not price.Our General Public Licenses are designed to make sure

that you have the freedom to distribute copies of free software

(and charge for this service if you wish), that you receive source

code or can get it if you want it, that you can change the software

or use pieces of it in new free programs; and that you know you

can do these things.

2. You may modify your copy or copies of the Program or any

portion of it, thus forming a work based on the Program, and

copy and distribute such modiﬁcations or work under the

terms of Section 1 above, provided that you also meet all of

these conditions:

a)You must cause the modiﬁed ﬁles to carry prominent notices

stating that you changed the ﬁles and the date of any change.

b)You must cause any work that you distribute or publish, that

in whole or in part contains or is derived from the Program

or any part thereof, to be licensed as a whole at no charge

to all third parties under the terms of this License.

c) If the modiﬁed program normally reads commands

interactively when run, you must cause it, when started

running for such interactive use in the most ordinary way, to

print or display an announcement including an appropriate

else, saying that you provide a warranty) and that users may

redistribute the program under these conditions, and telling

the user how to view a copy of this License. (Exception: if

the Program itself is interactive but does not normally print

such an announcement, your work based on the Program is

not required to print an announcement.)

To protect your rights, we need to make restrictions that forbid

anyone to deny you these rights or to ask you to surrender the

rights. These restrictions translate to certain responsibilities for

you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether

gratis or for a fee, you must give the recipients all the rights that

you have.You must make sure that they, too, receive or can get

the source code. And you must show them these terms so they

know their rights.

We protect your rights with two steps:(1) copyright the software,

and (2) offer you this license which gives you legal permission to

copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make

certain that everyone understands that there is no warranty

for this free software. If the software is modiﬁed by someone

else and passed on, we want its recipients to know that what

they have is not the original, so that any problems introduced by

others will not reﬂect on the original authors’ reputations.

These requirements apply to the modiﬁed work as a whole.

If identiﬁable sections of that work are not derived from the

Program, and can be reasonably considered independent and

separate works in themselves, then this License, and its terms,

do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections

as part of a whole which is a work based on the Program,

the distribution of the whole must be on the terms of this

License, whose permissions for other licensees extend to the

entire whole, and thus to each and every part regardless of

who wrote it.

Finally, any free program is threatened constantly by software

patents.We wish to avoid the danger that redistributors of a free

program will individually obtain patent licenses, in effect making

the program proprietary.To prevent this, we have made it clear

that any patent must be licensed for everyone’s free use or not

licensed at all.

The precise terms and conditions for copying, distribution and

modiﬁcation follow.

Download from Www.Somanuals.com. All Manuals Search And Download.

impose any further restrictions on the recipients’ exercise of

the rights granted herein.You are not responsible for enforcing

compliance by third parties to this License.

Thus,it is not the intent of this section to claim rights or contest

your rights to work written entirely by you; rather, the intent is

to exercise the right to control the distribution of derivative or

collective works based on the Program.

7. If, as a consequence of a court judgment or allegation of

patent infringement or for any other reason (not limited to

patent issues), conditions are imposed on you (whether by

court order, agreement or otherwise) that contradict the

conditions of this License, they do not excuse you from the

conditions of this License. If you cannot distribute so as to

satisfy simultaneously your obligations under this License and

any other pertinent obligations, then as a consequence you

may not distribute the Program at all. For example, if a patent

license would not permit royalty-free redistribution of the

Program by all those who receive copies directly or indirectly

through you, then the only way you could satisfy both it and

this License would be to refrain entirely from distribution of

the Program.

In addition, mere aggregation of another work not based on

the Program with the Program (or with a work based on the

Program) on a volume of a storage or distribution medium

does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on

it, under Section 2) in object code or executable form under

the terms of Sections 1 and 2 above provided that you also do

one of the following:

a) Accompany it with the complete corresponding machine-

readable source code, which must be distributed under the

terms of Sections 1 and 2 above on a medium customarily

used for software interchange; or,

b) Accompany it with a written offer, valid for at least three

years, to give any third party, for a charge no more than your

cost of physically performing source distribution, a complete

machine-readable copy of the corresponding source code, to

be distributed under the terms of Sections 1 and 2 above on a

medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the

offer to distribute corresponding source code.(This alternative

is allowed only for noncommercial distribution and only if you

received the program in object code or executable form with

such an offer, in accord with Subsection b above.)

If any portion of this section is held invalid or unenforceable

under any particular circumstance, the balance of the section

is intended to apply and the section as a whole is intended to

apply in other circumstances.

It is not the purpose of this section to induce you to infringe any

patents or other property right claims or to contest validity of

any such claims;this section has the sole purpose of protecting

the integrity of the free software distribution system, which

is implemented by public license practices. Many people have

made generous contributions to the wide range of software

distributed through that system in reliance on consistent

application of that system; it is up to the author/donor to

decide if he or she is willing to distribute software through any

other system and a licensee cannot impose that choice.

The source code for a work means the preferred form of

the work for making modiﬁcations to it. For an executable

work, complete source code means all the source code for all

modules it contains,plus any associated interface deﬁnition ﬁles,

plus the scripts used to control compilation and installation of

the executable. However, as a special exception, the source

code distributed need not include anything that is normally

distributed (in either source or binary form) with the major

components (compiler, kernel, and so on) of the operating

system on which the executable runs, unless that component

itself accompanies the executable.

This section is intended to make thoroughly clear what is

believed to be a consequence of the rest of this License.

8. if the distribution and/or use of the Program is restricted in

certain countries either by patents or by copyrighted interfaces,

the original copyright holder who places the Program under

this License may add an explicit geographical distribution

limitation excluding those countries, so that distribution is

permitted only in or among countries not thus excluded. In

such case, this License incorporates the limitation as if written

in the body of this License.

If distribution of executable or object code is made by offering

access to copy from a designated place,then offering equivalent

access to copy the source code from the same place counts as

distribution of the source code, even though third parties are

not compelled to copy the source along with the object code.

9. The Free Software Foundation may publish revised and/or new

versions of the General Public License from time to time. Such

new versions will be similar in spirit to the present version, but

may differ in detail to address new problems or concerns.

4. You may not copy,modify,sublicense,or distribute the Program

except as expressly provided under this License. Any attempt

otherwise to copy, modify, sublicense or distribute the Program

is void, and will automatically terminate your rights under

this License. However, parties who have received copies, or

rights, from you under this License will not have their licenses

terminated so long as such parties remain in full compliance.

Each version is given a distinguishing version number. If the

Program speciﬁes a version number of this License which

applies to it and “any later version”, you have the option of

following the terms and conditions either of that version or of

any later version published by the Free Software Foundation.

If the Program does not specify a version number of this

License, you may choose any version ever published by the

Free Software Foundation.

5. You are not required to accept this License, since you have

not signed it. However, nothing else grants you permission to

modify or distribute the Program or its derivative works.These

actions are prohibited by law if you do not accept this License.

Therefore, by modifying or distributing the Program (or any

work based on the Program), you indicate your acceptance

of this License to do so, and all its terms and conditions for

copying, distributing or modifying the Program or works based

on it.

10. If you wish to incorporate parts of the Program into other

free programs whose distribution conditions are different,

write to the author to ask for permission. For software which

is copyrighted by the Free Software Foundation, write to the

Free Software Foundation; we sometimes make exceptions

for this. Our decision will be guided by the two goals of

preserving the free status of all derivatives of our free software

and of promoting the sharing and reuse of software generally.

6. Each time you redistribute the Program (or any work based

on the Program), the recipient automatically receives a license

from the original licensor to copy, distribute or modify the

Program subject to these terms and conditions.You may not

Download from Www.Somanuals.com. All Manuals Search And Download.

III

Gnomovision version 69, Copyright (C) year name of author

Gnomovision comes with ABSOLUTELY NO WARRANTY; for

details type `show w’. This is free software, and you are welcome

to redistribute it under certain conditions; type `show c’ for

details.

NOWARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF

CHARGE, THERE IS NO WARRANTY FOR THE

PROGRAM,TOTHE EXTENT PERMITTED BY APPLICABLE

LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING

THE COPYRIGHT HOLDERS AND/OR OTHER

PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE

RISK AS TO THE QUALITY AND PERFORMANCE OF

THE PROGRAM IS WITHYOU. SHOULDTHE PROGRAM

PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL

NECESSARY SERVICING, REPAIR OR CORRECTION.

The hypothetical commands `show w’ and `show c’ should show

the appropriate parts of the General Public License. Of course,

the commands you use may be called something other than

`show w’ and `show c’; they could even be mouse-clicks or menu

items--whatever suits your program.

You should also get your employer (if you work as a programmer)

or your school, if any, to sign a “copyright disclaimer” for the

program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the

program `Gnomovision’ (which makes passes at compilers)

written by James Hacker.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW

OR AGREED TO IN WRITING WILL ANY COPYRIGHT

HOLDER, OR ANY OTHER PARTY WHO MAY

MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS

PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,

INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES ARISING OUT

OF THE USE OR INABILITY TO USE THE PROGRAM

(INCLUDING BUT NOT LIMITED TO LOSS OF DATA

OR DATA BEING RENDERED INACCURATE OR LOSSES

SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE

OF THE PROGRAM TO OPERATE WITH ANY OTHER

PROGRAMS),EVEN IF SUCH HOLDER OR OTHER PARTY

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

signature ofTy Coon, 1 April 1989

Ty Coon, President ofVice

This General Public License does not permit incorporating

your program into proprietary programs. If your program is a

subroutine library, you may consider it more useful to permit

linking proprietary applications with the library. If this is what you

want to do, use the GNU Lesser General Public License instead

of this License.

If you are interested in obtaining GPL source code used in this

product, please contact

FUNAI SERVICE CORPORATION

2200 Spiegel Drive, Groveport, OH 43125

[email protected]

END OFTERMS AND CONDITIONS

How to ApplyTheseTerms toYour New Programs

If you develop a new program, and you want it to be of the

greatest possible use to the public, the best way to achieve this

is to make it free software which everyone can redistribute and

change under these terms.

jpeglib.h

This software is based in part on the work of the Independent

JPEG Group.

To do so, attach the following notices to the program. It is safest

to attach them to the start of each source ﬁle to most effectively

convey the exclusion of warranty; and each ﬁle should have at

least the “copyright” line and a pointer to where the full notice

is found.

FreeType

2009The FreeType Project (www.freetype.org). All rights

reserved.

one line to give the program’s name and an idea of what it does.

This program is free software; you can redistribute it and/or

modify it under the terms of the GNU General Public License

as published by the Free Software Foundation; either version 2

of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful,

but WITHOUT ANY WARRANTY; without even the

implied warranty of MERCHANTABILITY or FITNESS FOR A

PARTICULAR PURPOSE. See the GNU General Public License

for more details.

You should have received a copy of the GNU General Public

License along with this program;if not, write to the Free Software

Foundation,Inc.,51 Franklin Street,Fifth Floor,Boston,MA 02110-

1301, USA.

Also add information on how to contact you by electronic and

paper mail.

If the program is interactive,make it output a short notice like this

when it starts in an interactive mode:

Download from Www.Somanuals.com. All Manuals Search And Download.

Shoprider Mobility Aid 888WNLM User Manual
Singer Sewing Machine FW 75 User Manual
Sony DVD VCR Combo RDR VX555 User Manual
Sony Home Theater System D E356CK User Manual
Sony Microcassette Recorder MZ E800 User Manual
Sony Microcassette Recorder TCS 100DV User Manual
Sony Microcassette Recorder WM GX550 User Manual
Sony Power Supply AC LS1 User Manual
Sylvania Flat Panel Television 6427TEL User Manual
Sylvania Flat Panel Television LC320SS1 User Manual