®
User
Quickie Match Point
NOTE– Not recommended for everyday use. This prod-
uct was designed for tennis court uses only.
With the standard 5th wheel this product can
only be ridden on smooth and even surfaces.
Instruction
Manual &
Warranty
Supplier:
Rider:
This manual must be given to
the rider of this wheelchair.
Before using this wheelchair
read this entire manual and
save for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
I I . T a b l e o f C o n t e n t s
I I . T a b l e o f C o n t e n t s
VIII. WARNINGS: COMPONENTS & OPTIONS ..................................................... 22
A. Anti-Tip Tubes................................................................................... 22
B. Armrests .......................................................................................... 22
C. Cushion & Sling Seats ........................................................................ 22
D. Fasteners.......................................................................................... 23
E. Footrests.......................................................................................... 23
F. Pneumatic Tires................................................................................. 23
G. Positioning Belts............................................................................... 24
H. Power Drive ...................................................................................... 24
I. Push Handles.................................................................................... 24
J. Quick-Release Axles ........................................................................... 25
K. Rear Wheels...................................................................................... 25
L. Rear Wheel Locks............................................................................... 25
M. Modified Seat Systems........................................................................ 26
N. Upholstery Fabric............................................................................... 26
IX. CHAIR BASICS ...................................................................................... 27
A. To Mount & Remove Rear Wheels ......................................................... 27
X. SET-UP AND ADJUSTMENT...................................................................... 28
A. Set-up ............................................................................................. 28
B. Quick-Release Axle............................................................................. 28
C. Backrest (fixed or folding).................................................................. 29
D. Seat Sling......................................................................................... 30
E. Cushion............................................................................................ 30
F. Rear Axle Assembly............................................................................ 30
G. Caster Forks...................................................................................... 32
H. Footrest ........................................................................................... 33
I. Integral 5th Wheel............................................................................. 33
J. Check-out......................................................................................... 34
XI. TROUBLESHOOTING............................................................................... 35
XII. MAINTENANCE...................................................................................... 36
A. Introduction ..................................................................................... 36
B. Maintenance Chart............................................................................. 36
C. Maintenance Tips............................................................................... 37
D. Cleaning........................................................................................... 37
E. Storage Tips...................................................................................... 37
XIII. SUNRISE LIMITED WARRANTY................................................................. 38
I. INTRODUCTION.....................................................................................
II. TABLE OF CONTENTS..............................................................................
III. YOUR CHAIR AND ITS PARTS ..................................................................
IV. NOTICE - READ BEFORE USE...................................................................
A. Choose the Right Chair & Safety Option................................................
B. Review this Manual Often ..................................................................
C. Warnings..........................................................................................
V. GENERAL WARNINGS.............................................................................
A. Weight Limit.....................................................................................
B. Weight Training.................................................................................
C. Getting to Know Your Chair.................................................................
D. To Reduce The Risk of an Accident .......................................................
E. Safety Checklist ................................................................................ 10
F. Changes & Adjustments ...................................................................... 10
G. Environmental Conditions ................................................................... 10
H. Terrain............................................................................................. 11
I. Street Use ........................................................................................ 11
J. Motor Vehicle Safety .......................................................................... 11
K. When You Need Help.......................................................................... 12
VI. WARNINGS: FALLS & TIP-OVERS ............................................................. 13
A. Center of Balance ............................................................................. 13
B. Dressing or Changing Clothes ............................................................. 13
C. Wheelies ......................................................................................... 14
D. Obstacles ........................................................................................ 14
E. Reaching or Leaning ......................................................................... 15
F. Moving Backward .............................................................................. 15
G. Ramps, Slopes & Side Hills ................................................................. 16
H. Transfer............................................................................................ 17
I. Curbs & Steps ................................................................................... 17
J. Stairs............................................................................................... 18
K. Escalators......................................................................................... 18
VII. WARNINGS: FOR SAFE USE..................................................................... 19
A. Learning to do a “Wheelie”................................................................. 19
B. Descending a Curb or Single Step......................................................... 19
C. Climbing a Curb or Single Step ............................................................ 20
D. Climbing Stairs.................................................................................. 20
E. Descending Stairs.............................................................................. 20
F. Maintenance ..................................................................................... 21
3
4
6
8
8
8
8
9
9
9
9
9
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
I I I . Y o u r C h a i r
&
I t s P a r t s
I I I . Y o u r C h a i r
&
I t s P a r t s
INTEGRAL 5TH WHEEL OPTION
WEIGHT
Single Integral
20 lbs. with 24" 559 heat-treated ten-
nis wheels.
Opt - Quick-Release
2
AXLE ASSEMBLY
COLOR
1
Camber: 16º, 20º eccentric
axle sleeve
Blue, black, red, midnight purple, pearl
pink, forest green, yellow, blue green,
candy teal, candy purple, black opal,
toxic green
AXLES
4
6
Std - stainless steel
3
Opt - titanium, quad-release axle nuts
FRAME DIMENSIONS
Frame width: 13"-19.5"
WHEELS
Std - cross-spoked
Sling depth: 13"-18"
Quickie Performance wheels: heat-treat-
ed tennis
Size: 24", 25", 26"
Tires: high-pressure clinchers, latex-
tubular
Handrims: aluminum-anodized, lava
black coated, plastic-coated
Rear seat height: 13"-21"
Front seat height: 17"-21"
Frame length: short, medium
Frame modifications: custom
Cushion: 2"
11
12
BACKREST
Fixed or folding - height adjustable:
10"-14", 12"-15", 14"-17", 16"-19"
Tabs: Short, Regular
All features may not be available with
some chair setups or in conjunction with
another chair feature. Please consult your
authorized Quickie Sports Center supplier
for more information. Your authorized
Quickie Sports Center supplier can also
provide you with more information on
Quickie accessories and Quickie clothing.
7
UPHOLSTERY
Std - Quickie Sports style
9
5
15
10
FOOTREST
8
14
13
Platform
CASTERS
3" micros
Q u i c k i e M a t c h P o i n t
1. Backrest
2. Tire
9. Quick-release axle
10. Wheel rim
3. Seat cushion
4. Seat sling
5. Footrest
6. Handrim
7. Spokes
11. Camber Tube
12. Caster housing
13. Caster fork
14. Caster
15. Rear Seat Tube
8. Rear wheel hub
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
8
9
I V . N o t i c e – R e a d B e f o r e U s e
V .
G e n e r a l W a r n i n g s
A. WEIGHT LIMIT
NOTE– Not recommended for everyday use. This product was designed for tennis court
uses only. With the standard 5th wheel this product can only be ridden on
smooth and even surfaces. These are general warnings and might not apply to
this sports product.
NEVER exceed the weight limit of 250 pounds (113.6 kilograms), for combined weight
of rider and items carried. If you do exceed the limit, damage to your chair, a fall, tip-
over or loss of control may occur and cause severe injury to the rider or others.
A. CHOOSE THE RIGHT CHAIR & SAFETY OPTIONS
Quickie provides a choice of many wheelchair styles to meet the needs of the wheel-
chair rider. However, final selection of the type of wheelchair, options and adjustments
rests solely with you and your health care advisor. Choosing the best chair and set-up
for your safety depends on such things as:
B. WEIGHT TRAINING
NEVER use this chair for weight training if total weight (rider plus equipment) exceeds
250 pounds. If you do exceed the limit, damage to your chair, a fall, tip-over or loss
of control may occur and cause severe injury to the rider or others.
1. Your disability, strength, balance and coordination.
2. The types of hazards you must overcome in daily use (where you live and work,
and other places you are likely to use your chair).
3. The need for options for your safety and comfort (such as anti-tip tubes, posi-
tioning belts or special seating systems).
C. GETTING TO KNOW YOUR CHAIR
B. REVIEW THIS MANUAL OFTEN
Every wheelchair is different. Take the time to learn the feel of this chair before you
begin riding. Start slowly, with easy, smooth strokes. If you are used to a different
chair, you may use too much force and tip over. If you use too much force, damage to
your chair, a fall, tip-over or loss of control may occur and cause severe injury to the
rider or others.
Before using this chair you, and each person who may assist you, should
read this entire manual and make sure to follow all instructions. Review the warnings
often, until they are second nature to you.
C. WARNINGS
The word “WARNING” refers to a hazard or unsafe practice that may cause severe
injury or death to you or to other persons. The “Warnings” are in three main sections,
as follows:
D. TO REDUCE THE RISK OF AN ACCIDENT
1. BEFORE riding, you should be trained in the safe use of this chair by your health
care advisor.
2. Practice bending, reaching and transfers until you know the limit of your ability.
Have someone help you until you know what can cause a fall or
tip-over and how to avoid doing so.
3. Be aware that you must develop your own methods for safe use best
suited to your level of function and ability.
4. NEVER try a new maneuver on your own until you are sure you can
do it safely.
5. Get to know the areas where you plan to use your chair. Look for
hazards and learn how to avoid them.
6. Use anti-tip tubes unless you are a skilled rider of this chair and are sure you
are not at risk to tip over.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss
of control may occur and cause severe injury to the rider or others.
1.V — GENERAL WARNINGS
Here you will find a safety checklist and a summary of risks you need to be
aware of before you ride this chair.
2.VI — WARNINGS — FALLS & TIP-OVERS
Here you will learn how to avoid a fall or tip-over while you perform daily activi-
ties in your chair.
3.VII — WARNINGS — FOR SAFE USE
Here you will learn about practices for the safe use of your chair
4.VIII — WARNINGS — COMPONENTS & OPTIONS
Here you will learn about the components of your chair and options you can
select for safety. Consult your authorized Quickie supplier and your health care
advisor to help you choose the best set-up and options for safe use.
NOTE– Where they apply, you will also find “Warnings” in other sections of this manu-
al. Heed all warnings in this section. If you fail to do so a fall, tip-over or loss
of control may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
10
11
V .
G e n e r a l W a r n i n g s
V .
G e n e r a l W a r n i n g s
H. TERRAIN
E. SAFETY CHECKLIST
Before Each Use Of Your Chair:
1. Your chair is designed for use on firm, even surfaces such as concrete,
asphalt and indoor floors and carpeting.
2. Do not operate your chair in sand, loose soil or over rough terrain.
This may damage wheels or axles, or loosen fasteners of your chair.
1. Make sure the chair rolls easily and that all parts work smoothly. Check for noise,
vibration, or a change in ease of use. (They may indicate low tire pressure, loose
fasteners, or damage to your chair).
2. Repair any problem. Your authorized Quickie supplier can help you find and cor-
rect the problem.
3. Check to see that both quick-release rear axles are locked. When locked, the axle
button will “pop out” fully. If not locked, the wheel may come off and cause you
to fall.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
I. STREET USE
4. If your chair has anti-tip tubes, lock them in place.
NOTE– See “Anti-Tip Tubes” (Section VIII) for times you should not use them.
In most states, wheelchairs are not legal for use on public roads. Be alert to the dan-
ger of motor vehicles on roads or in parking lots.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
1. At night, or when lighting is poor, use reflective tape on your chair
and clothing.
F. CHANGES & ADJUSTMENTS
2. Due to your low position, it may be hard for drivers to see you. Make eye con-
tact with drivers before you go forward. When in doubt, yield until you are sure
it is safe.
1. If you modify or adjust this chair, it may increase the risk of a tip-over UNLESS
you make other changes as well.
2. Consult your authorized Quickie supplier BEFORE you modify or adjust your chair.
3. We recommend that you use anti-tip tubes until you adapt to the change, and
are sure you are not at risk to tip over.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
J. MOTOR VEHICLE SAFETY
4. Unauthorized modifications or use of parts not supplied or approved by Sunrise
may change the chair structure. This will void the warranty and may cause a
safety hazard.
Quickie wheelchairs do not meet federal standards for motor vehicle seating.
1. NEVER let anyone sit in this chair while in a moving vehicle.
a. ALWAYS move the rider to an approved vehicle seat.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
b. ALWAYS secure the rider with proper motor vehicle restraints.
2. In an accident or sudden stop the rider may be thrown from the chair.
Wheelchair seat belts will not prevent this, and further injury may result from
the belts or straps.
3. NEVER transport this chair in the front seat of a vehicle. It may shift and inter-
fere with the driver.
G. ENVIRONMENTAL CONDITIONS
1. Use extra care if you must ride your chair on a wet or slick surface.
If you are in doubt, ask for help.
2. Contact with water or excess moisture may cause your chair to rust or corrode.
This could cause your chair to fail.
a. Do not use your chair in a shower, pool or other body of water. The chair tub-
ing and parts are not water-tight and may rust or corrode from the inside.
b. Avoid excess moisture (for example, do not leave your chair in a damp bath-
room while taking a shower).
4. ALWAYS secure this chair so that it cannot roll or shift.
5. Do not use any chair that has been involved in a motor vehicle accident.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
c. Dry your chair as soon as you can if it gets wet, or if you use water to clean it.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
12
13
V .
G e n e r a l W a r n i n g s
V I .
W a r n i n g s : F a l l s
&
T i p - O v e r s
A. CENTER OF BALANCE
K. WHEN YOU NEED HELP
For The Rider:
The point where this chair will tip forward, back, or to the side depends on its center
of balance and stability. How your chair is set up, the options you select and the
changes you make may affect the risk of a fall or tip-over.
Make sure that each person who helps you reads and follows all warnings and instruc-
tions that apply.
1. The Most Important Adjustments Are:
a. The position of the rear wheels. The more you move your seat back, the more
likely your chair will tip over backward.
2. The Center Of Balance Is Also Affected By:
a. A change in the set-up of your chair, including:
• The distance between the rear wheels.
For Attendants:
1. Work with the rider’s doctor, nurse or therapist to learn safe methods best suited
to your abilities and those of the rider.
2. Tell the rider what you plan to do, and explain what you expect the rider to do.
This will put the rider at ease and reduce the risk of an accident.
3. Make sure the chair has push handles. They provide secure points for you to hold
the rear of the chair to prevent a fall or tip-over. Check to make sure push han-
dle grips will not rotate or slip off.
4. To prevent injury to your back, use good posture and proper body mechanics.
When you lift or support the rider or tilt the chair, bend your knees slightly and
keep your back as upright and straight as you can.
5. Remind the rider to lean back when you tilt the chair backward.
6. When you descend a curb or single step, slowly lower the chair in one easy
movement. Do not let the chair drop the last few inches to the ground.
This may damage the chair or injure the rider.
7. To avoid tripping, unlock and rotate anti-tip tubes up, out of the way. ALWAYS
lock the rear wheels, and lock anti-tip tubes in place if you must leave the rider
alone, even for a moment. This will reduce the risk of a tip-over or loss of con-
trol of the chair.
• The amount of rear wheel camber.
• The seat height and seat angle.
• Backrest angle.
b. A change in your body position, posture or weight distribution.
c. Riding your chair on a ramp or slope.
d. The use of a back pack or other options and the amount of added weight.
3. To Reduce The Risk Of An Accident:
a. Consult your doctor, nurse or therapist to find out what axle
and caster position is best for you.
b. Consult your authorized Quickie supplier BEFORE you modify or adjust this
chair. Be aware that you may need to make other changes to correct the cen-
ter of balance.
c. Have someone help you until you know the balance points of your chair and
how to avoid a tip-over.
d. Use anti-tip tubes.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
B. DRESSING OR CHANGING CLOTHES
Your weight may shift if you dress or change clothes while seated in this chair.
To reduce the risk of a fall or tip-over:
1. Rotate the front casters until they are as far forward as possible.
This makes the chair more stable.
2. Lock anti-tip tubes in place. (If your chair does not have anti-tip tubes, back it
up against a wall and lock both rear wheels).
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
14
15
V I .
W a r n i n g s : F a l l s
&
T i p - O v e r s
V I .
W a r n i n g s : F a l l s
&
T i p - O v e r s
E. REACHING OR LEANING
C. WHEELIES
If you reach or lean it will affect the center of balance of your chair. This may cause you
to fall or tip over. When in doubt, ask for help or use a device to extend your reach.
Doing a “wheelie” means: balancing on the rear wheels of your chair, while
the front casters are in the air. It is dangerous to do a “wheelie” as a fall or
tip-over may occur. However, if you do it safely, a “wheelie” can help you
overcome curbs and obstacles.
1. NEVER reach or lean if you must shift your weight sideways or rise up off the seat.
2. NEVER reach or lean if you must move forward in your seat to do so. Always
keep your buttocks in contact with the backrest.
1. Consult your doctor, nurse or therapist to find out if you are a good candidate to
3. NEVER reach with both hands (you may not be able to catch yourself
to prevent a fall if the chair tips).
4. NEVER reach or lean to the rear unless your chair has anti-tip tubes locked in place.
5. DO NOT reach or lean over the top of the seat back. This may damage one or
both backrest tubes and cause you to fall.
6. If You Must Reach Or Lean:
a. Do not lock the rear wheels. This creates a tip point and makes a fall or tip-
over more likely.
learn to do a “wheelie.”
2. Do not attempt a “wheelie” UNLESS you are a skilled rider of this chair or you
have help.
NOTE– See p. 19 for steps to learn to do a “wheelie.”
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
D. OBSTACLES
b. Do not put pressure on the footrests.
NOTE– Leaning forward puts pressure on the footrests and may cause the chair to
tip if you lean too far.
Obstacles and road hazards (such as potholes and broken pavement) can
damage your chair and may cause a fall, tip-over or loss of control.
c. Move your chair as close as you can to the object you wish to reach.
d. Do not try to pick up an object from the floor by reaching down between your
knees. You are less likely to tip if you reach to the side of your chair.
e. Rotate the front casters until they are as far forward as possible. This makes
the chair more stable.
To avoid these risks:
1. Keep a lookout for danger – scan the area well ahead of your chair
as you ride.
NOTE– To do this: Move your chair past the object you want to reach, then back
up alongside it. Backing up will rotate the casters forward.
f. Firmly grasp a rear wheel or an armrest with one hand. This will help
to prevent a fall if the chair tips.
2. Make sure the floor areas where you live and work are level and
free of obstacles.
3. Remove or cover threshold strips between rooms.
4. Install a ramp at entry or exit doors. Make sure there is not a drop off at the
bottom of the ramp.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
5. To Help Correct Your Center Of Balance:
a. Lean your upper body FORWARD slightly as you go UP over an obstacle.
b. Press your upper body BACKWARD as you go DOWN from a higher to a
lower level.
F. MOVING BACKWARD
6. If your chair has anti-tip tubes, lock them in place before you go UP
over an obstacle.
7. Keep both of your hands on the handrims as you go over an obstacle.
8. Never push or pull on an object (such as furniture or a doorjamb) to
propel your chair.
Use extra care when you move your chair backward. Your chair is most stable when you
propel yourself forward. You may lose control or tip over if one of the rear wheels hits
an object and stops rolling.
1. Propel your chair slowly and smoothly.
2. If your chair has anti-tip tubes, make sure to lock them in place.
3. Stop often and check to be sure your path is clear.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
16
17
V I .
W a r n i n g s : F a l l s
&
T i p - O v e r s
V I .
W a r n i n g s : F a l l s
&
T i p - O v e r s
H. TRANSFER
G. RAMPS, SLOPES & SIDE HILLS
It is dangerous to transfer on your own. It requires good balance and agility. Be aware
that there is a point during every transfer when the wheelchair seat is not below you.
To Avoid A Fall:
Riding on a slope, which includes a ramp or side hill, will change the center of
balance of your chair. Your chair is less stable when it is at an angle. Anti-tip tubes
may not prevent a fall or tip-over.
1. Work with your health care advisor to learn safe methods.
a. Learn how to position your body and how to support yourself during
a transfer.
b. Have someone help you until you know how to do a safe transfer on your own.
2. Lock the rear wheels before you transfer. This keeps the rear wheels from rolling.
NOTE– This will NOT keep your chair from sliding away from you or tipping.
3. Make sure to keep pneumatic tires properly inflated. Low tire pressure may allow
the rear wheel locks to slip.
4. Move your chair as close as you can to the seat you are transferring to.
If possible, use a transfer board.
5. Rotate the front casters until they are as far forward as possible.
6. If you can, remove or swing footrests out of the way.
a. Make sure your feet do not catch in the space between the footrests.
b. Avoid putting weight on the footrests as this may cause the chair to tip.
7. Make sure armrests are out of the way and do not interfere.
8. Transfer as far back onto the seat surface as you can. This will reduce the risk
that the chair will tip or move away from you.
1. Do not use your chair on a slope steeper than 10%. (A 10% slope means: one
foot in elevation for every ten feet of slope length.)
2. Always go as straight up and as straight down as you can. (Do not “cut the cor-
ner” on a slope or ramp.)
3. Do not turn or change direction on a slope.
4. Always stay in the CENTER of the ramp. Make sure ramp is wide enough that you
are not at risk that a wheel may fall over the edge.
5. Do not stop on a steep slope. If you stop, you may lose control of your chair.
6. NEVER use rear wheel locks to try to slow or stop your chair.
This is likely to cause your chair to veer out of control.
7. Beware Of:
a. Wet or slippery surfaces.
b. A change in grade on a slope (or a lip, bump or depression). These may cause
a fall or tip-over.
c. A drop-off at the bottom of a slope. A drop-off of as small as 3/4 inch can
stop a front caster and cause the chair to tip forward.
8. To Reduce The Risk Of A Fall Or Tip-Over:
a. Lean or press your body UPHILL. This will help adjust for the change in the
center of balance caused by the slope or side hill.
b. Keep pressure on the handrims to control your speed on a down slope.
If you go too fast you may lose control.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
I. CURBS & STEPS
c. Ask for help any time you are in doubt.
9. Ramps At Home & Work - For your safety, ramps at home and work must meet all
legal requirements for your area. We recommend:
a. Width. At least four feet wide.
b. Guardrails. To reduce the risk of a fall, sides of ramp must have guardrails (or
raised borders at least three inches high).
1. Each person who helps you should read and follow the warnings
“For Safe Use” (Section VII).
2. Do not try to climb or descend a curb or step alone UNLESS you
are a skilled rider of this chair and:
a. You can safely do a “wheelie”; and
b. You are sure you have the strength and balance to do so.
3. Unlock and rotate anti-tip tubes up, out of the way, so they do not interfere.
4. Do not try to climb a high curb or step (more than 4 inches high) UNLESS you
have help. Doing so may cause your chair to exceed its balance point and tip over.
5. Go straight up and straight down a curb or step. If you climb or descend at an
angle, a fall or tip-over is likely.
c. Slope. Not more than a 10% grade.
d. Surface. Flat and even, with a thin carpet or other non-skid material.
(Make sure there is no lip, bump or depression.)
e. Bracing. Ramp must be STURDY. You may need bracing so ramp does not
“bow” when you ride on it.
f. Avoid A Drop Off. You may need a section at the top or bottom to smooth out
the transition.
6. Be aware that the impact of dropping down from a curb or step can damage your
chair or loosen fasteners.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
18
19
V I .
W a r n i n g s : F a l l s
&
T i p - O v e r s
V I I .
W a r n i n g s : F o r S a f e U s e
J. STAIRS
Before you assist a rider, be sure to read the warnings “For Attendants” (p. 12) and
follow all instructions that apply. Be aware that you will need to learn safe methods
best suited to your abilities.
1. NEVER use this chair on stairs UNLESS you have someone to help you.
Doing so is likely to cause a fall or tip-over.
2. Persons who help you should read and follow the warnings
“For Attendants” (p. 12), and the “For Safe Use” (Section VII).
A. LEARNING TO DO A “WHEELIE”
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
Follow these steps to help the rider learn to do a “wheelie”:
1. Read and follow the warnings for “WHEELIES.” (See p. 14)
2. Stand at the rear of the chair. You must be able to move with the chair to
prevent a tip-over.
K. ESCALATORS
NEVER use this chair on an escalator, even with an attendant.
If you do, a fall or tip-over is likely.
3. Keep your hands BENEATH the push handles, ready to catch the rider if the chair
tips back.
4. When you are ready, have the rider place his or her hands on the forward part of
the handrims.
5. Have the rider make a quick BACKWARD movement of the rear wheels, quickly
followed by a hard FORWARD thrust. (This will tilt the chair up on the balance
point of the rear wheels.)
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
6. Have the rider make small movements of the handrims to stay in balance.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
B. DESCENDING A CURB OR SINGLE STEP
Follow these steps to help a rider descend a curb or single step going BACKWARD:
1. Stay at the rear of the chair.
2. Several feet before your reach the edge of the curb or step, turn the chair
around and pull it backward.
3. While looking over your shoulder, carefully step back until you are off the curb
or stair and standing on the lower level.
4. Pull the chair toward you until the rear wheels reach the edge of the curb or
step. Then allow the rear wheels to slowly roll down onto the lower level.
5. When the rear wheels are safely on the lower level, tilt the chair back to its bal-
ance point. This will lift the front casters off the curb or step.
6. Keep the chair in balance and take small steps backward. Turn the chair around
and gently lower front casters to the ground.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
20
21
V I I .
W a r n i n g s : F o r S a f e U s e
V I I .
W a r n i n g s : F o r S a f e U s e
F. MAINTENANCE
C. CLIMBING A CURB OR SINGLE STEP
1. Inspect and maintain this chair strictly per chart.
Follow these steps to help the rider climb a curb or single step going FORWARD:
2. If you detect a problem, make sure to service or repair the chair before use.
3. At least once a year, have a complete inspection, safety check and service of
your chair made by an authorized Quickie supplier.
1. Stay behind the chair.
2. Face the curb and tilt the chair up on the rear wheels so that the front casters
clear the curb or step.
3. Move forward, placing the front casters on the upper level as soon as you are
sure they are past the edge.
4. Continue forward until the rear wheels contact the face of the curb or step. Lift
and roll the rear wheels to the upper level.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others. For additional mainte-
nance information see Section XII: Maintenance.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
D. CLIMBING STAIRS
1. Use at least two attendants to move a chair and rider up stairs.
2. Move the chair and rider BACKWARD up the stairs.
3. The person at the rear is in control. He or she tilts the chair back to its
balance point.
4. A second attendant at the front firmly grasps a non-detachable part of the front
frame and lifts the chair up and over one stair at a time.
5. The attendants move to the next stair up. Repeat for each stair, until you reach
the landing.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
E. DESCENDING STAIRS
1. Use at least two attendants to move a chair and rider down stairs.
2. Move the chair and rider FORWARD down the stairs.
3. The person at the rear is in control. He or she tilts the chair to the balance
point of the rear wheels and rolls it to the edge of the top step.
4. A second attendant stands on the third step from the top and grasps the chair
frame. He or she lowers the chair one step at a time by letting the rear wheels
roll over the stair edge.
5. The attendants move to the next stair down. Repeat for each stair, until you
reach the landing.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
22
23
V I I I .
W a r n i n g s : C o m p o n e n t s
&
O p t i o n s
V I I I .
W a r n i n g s : C o m p o n e n t s
&
O p t i o n s
D. FASTENERS
A. ANTI-TIP TUBES (OPTIONAL)
Many of the screws, bolts and nuts on this chair are special high-strength fasteners.
Use of improper fasteners may cause your chair to fail.
Anti-tip tubes can help keep your chair from tipping over backward in most
normal conditions.
1. ONLY use fasteners provided by an authorized Quickie supplier (or ones of the
same type and strength, as indicated by the markings on the heads).
2. Over- or under-tightened fasteners may fail or cause damage to chair parts.
3. If bolts or screws become loose, tighten them as soon as you can.
1. Sunrise Recommends Use Of Anti-Tip Tubes:
a. UNLESS you are a skilled rider of this chair and are sure you are not at risk to
tip over.
b. Each time you modify or adjust your chair. The change may make it easier to
tip backward. Use anti-tip tubes until you adapt to the change and are sure
you are not at risk to tip over.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
2. When locked in place (in the “down” position) anti-tip tubes should be BETWEEN
1 1/2 to 2 inches off the ground.
E. FOOTRESTS
a. If set too HIGH, they may not prevent a tip-over.
b. If set too LOW, they may “hang up” on obstacles you can expect in normal
use. If this occurs, you may fall or your chair may tip over.
3. Keep Anti-Tip Tubes Locked In Place UNLESS:
1. At the lowest point, footrests should be AT LEAST 2 1/2 INCHES off the ground.
If set too LOW, they may “hang up” on obstacles you can expect to find in nor-
mal use. This may cause the chair to stop suddenly and tip forward.
2. To Avoid A Trip Or Fall When You Transfer:
a. You have an attendant; or
b. You have to climb or descend a curb, or overcome an obstacle and can safely
do so without them. At these times, make sure anti-tip tubes are up, out of
the way.
a. Make sure your feet do not “hang up” or get caught in the space between the
footrests.
b. Avoid putting weight on the footrests, as the chair may tip forward.
3. NEVER lift this chair by the footrests. Footrests detach and will not bear the weight
of this chair. Lift this chair only by non-detachable parts of the main frame.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
B. ARMRESTS
F. PNEUMATIC TIRES
Armrests detach and will not bear the weight of this chair.
1. NEVER lift this chair by its armrests. They may come loose or break.
2. Lift this chair only by non-detachable parts of the main frame.
Proper inflation extends the life of your tires and makes your chair easier to use.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
1. Do not use this chair if any of the tires is under- or over-inflated. Check weekly
for proper inflation level, as listed on the tire sidewall.
2. Low pressure in a rear tire may cause the wheel lock on that side to slip and
allow the wheel to turn when you do not expect it.
C. CUSHIONS & SLING SEATS
3. Low pressure in any of the tires may cause the chair to veer to one side and
result in a loss of control.
4. Over-inflated tires may burst.
1. Quickie sling seats and standard foam cushions are not designed for the relief
of pressure.
2. If you suffer from pressure sores, or if you are at risk that they will occur, you may
need a special seat system or a device to control your posture. Consult your doc-
tor, nurse or therapist to find out if you need such a device for your well-being.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
24
25
V I I I .
W a r n i n g s : C o m p o n e n t s
&
O p t i o n s
V I I I .
W a r n i n g s : C o m p o n e n t s
&
O p t i o n s
J. QUICK-RELEASE AXLES
G. POSITIONING BELTS (OPTIONAL)
1. Do not use this chair UNLESS you are sure that both quick-release rear axles
are locked. An unlocked axle may come off during use and cause a fall.
2. An axle is not locked until the quick-release button pops out fully.
An unlocked axle may come off during use, resulting in a fall, tip-over or loss of
control and cause severe injury to the rider or others.
Use positioning belts ONLY to help support the rider’s posture. Improper use of these
belts may cause severe injury to or death of the rider.
1. Make sure the rider does not slide down in the wheelchair seat. If this occurs, the
rider may suffer chest compression or suffocate due to pressure from the belts.
2. The belts must be snug, but must not be so tight that they interfere with
breathing. You should be able to slide your open hand, flat, between the belt
and the rider.
3. A pelvic wedge or a similar device can help keep the rider from sliding down in
the seat. Consult with the rider’s doctor, nurse or therapist to find out if the
rider needs such a device.
4. Use positioning belts only with a rider who can cooperate. Make sure the rider
can easily remove the belts in an emergency.
5. NEVER Use Positioning Belts:
a. As a patient restraint. A restraint requires a doctor’s order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden stop the rider may be
thrown from the chair. Wheelchair seat belts will not prevent this, and further
injury may result from the belts or straps.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
K. REAR WHEELS
A change in set-up of the rear wheels will affect the center of balance of your chair.
1. The farther you move the rear axles FORWARD, the more likely it is that your
chair will tip over backward.
2. Consult your doctor, nurse or therapist to find the best rear axle set-up for your
chair. Do not change the set-up UNLESS you are sure you are not at risk to tip over.
3. Adjust the rear wheel locks after you make any change to the rear axles.
a. If you fail to do so, the locks may not work.
b. Make sure lock arms embed in tires at least 1/8 inch when locked.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
L. REAR WHEEL LOCKS
H. POWER DRIVE
Rear wheel locks are NOT designed to slow or stop a moving wheelchair. Use them only
to keep the rear wheels from rolling when your chair is at a complete stop.
Do not install a power drive on any Quickie wheelchair. If you do:
1. It will affect the center of balance of your chair and may cause a fall or tip-over.
2. It will alter the frame and void the warranty.
1. NEVER use rear wheel locks to try to slow or stop your chair when it is moving.
Doing so may cause you to veer out of control.
2. To keep the rear wheels from rolling, always set both rear wheel locks when you
transfer to or from your chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
I. PUSH HANDLES (OPTIONAL)
3. Low pressure in a rear tire may cause the wheel lock on that side to slip and
may allow the wheel to turn when you do not expect it.
4. Make sure lock arms embed in tires at least 1/8 inch when locked. If you fail to
do so, the locks may not work.
When you have an attendant, make sure that this chair has push handles.
1. Push handles provide secure points for an attendant to hold the rear of this
chair to prevent a fall or tip-over. Make sure to use push handles when you have
an attendant.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
2. Check to make sure push handle grips will not rotate or slip off.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
26
27
V I I I .
W a r n i n g s : C o m p o n e n t s
&
O p t i o n s
I X . C h a i r B a s i c s
A. TO MOUNT & REMOVE REAR WHEELS
M. MODIFIED SEAT SYSTEMS
Do not use this chair UNLESS you are sure both
quick-release axles are locked. An unlocked
axle may come off during use and cause a fall.
Use of a seat system not approved by Sunrise may alter the center of balance of this
chair. This may cause the chair to tip over.
1. Do not change the seat system of your chair UNLESS you consult your
authorized Quickie supplier first.
NOTE– Axle is not locked until:
a. The quick-release button pops out fully. (Fig. A)
b. After the quick-release button pops out fully,
grab wheel and pull with an outward motion. The
wheel should be locked in place. If wheel is not
locked please refer to axle adjustment (follow
steps on p.28).
2. Use of a seat system not approved by Sunrise may affect the folding mechanism
of this chair.
3. Use of a seating system not provided by Sunrise is prohibited for transit use.
1. Quick-release
Figure A
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
2
1. To Install Wheel:
N. UPHOLSTERY FABRIC
a. Depress quick-release button (1) fully. This will
release tension on ball bearings at other end.
b. Insert axle through hub of rear wheel.
c. Keep pressure on button (1) as you slide axle (2)
into axle sleeve (3).
d. Release button to lock axle in sleeve. Adjust axle
if it does not lock. (Follow steps at p. 28)
e. Repeat steps on other side.
1. Replace worn or torn fabric of seat and seat back as soon as you can.
If you fail to do so, the seat may fail.
2. Sling fabric will weaken with age and use. Look for fraying or thin spots,
or stretching of fabrics at rivet holes.
3. “Dropping down” into your chair will weaken fabric and result in the need to
inspect and replace the seat more often.
3
4. Be aware that laundering or excess moisture will reduce flame retardation
of the fabric.
2. To Remove Wheel:
a. Depress quick-release button (1) fully.
b. Remove wheel by sliding axle out of axle sleeve.
c. Repeat steps on other side.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of con-
trol may occur and cause severe injury to the rider or others.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
28
29
X . S e t - u p
&
A d j u s t m e n t
X . S e t - u p
&
A d j u s t m e n t
C. BACKREST (FIXED OR FOLDING)
A. SET-UP
The backrest comes standard with a 4" height adjust-
ment from 10 to 19 inches.
NOTE– Setting the wheelchair on a table or flat sur-
face, such as a workbench or table, helps make
these procedures easier.
A
1. Height Adjustment
NOTE– Torque Settings: A torque setting is the opti-
mum tightening which should be made on a
particular fastener. A torque wrench which mea-
sures in./lbs. should be used when tightening
fasteners on Quickie wheelchairs. Unless other-
wise noted, use a torque setting of 60 in./lbs.
when setting up this wheelchair.
a. Remove the backrest upholstery from the frame.
b. You will see the backrest tube which telescopes
into the frame and is secured by a screw (A) on
the side of the frame.
c. there are four holes, 1" apart, you may choose
from to set the back height.
d. After selecting the proper height, reinsert screw
(A). Slide the backrest upholstery back on with
the overlap portion unattached.
e. Secure VELCRO® style material on side tubes and
attach the excess overlap.
Quick Release
Button
B. QUICK-RELEASE AXLE
1. Installation
a. Depress the quick-release button on the axle.
b. Slide through wheel hub and into axle sleeve
until it locks.
c. The axle is not secured until the outside quick-
release button pops out to its fully extended
position.
2. Back Angle Adjustment
A 6° angle adjustment is standard on all Quickie sports
wheelchairs.
a. Remove bolt and nut on both sides of
wheelchair.
2. Adjustment
a. To adjust the axle you will need a 3/4" wrench
to turn the outside axle nuts.
b. Adjust back assembly to desired angle.
c. Reinsert bolt and nut on each side of
wheelchair.
d. Tighten bolts and nuts.
e. The adjustment on each side of the chair must
be exactly equal.
b. You will also need a 1/2" wrench to lodge the
ball bearings, on the opposite end of the axle,
and prevent the axle from turning.
c. Turn the outside axle nut counterclockwise to
tighten.
d. There should only be zero to ten thousandths of
an inch (.010) of play.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
30
31
X . S e t - u p
&
A d j u s t m e n t
X . S e t - u p
&
A d j u s t m e n t
1. Wheel Camber
D. SEAT SLING
Camber Tube
16° & 20°
Increasing wheel camber angle provides greater side-
to-side stability due to the increased width and angle
of the wheelbase and also allows for quicker turning
and greater access to the top of the handrims.
The seat sling can be adjusted through the use of
VELCRO® style retaining material beneath the seat.
1. Adjustment
a. Remove the screws retaining the left side seat
sling.
The wheel camber option from the factory is 16° & 20°.
b. Readjust VELCRO® style material to adjust the
tension in the seat sling.
c. Replace screws.
d. If there is any difficulty in reattaching the
screws, try using a probe to help line up the
holes.
2. Rear Wheel Axle Sleeve Adjustment
Tight axle sleeves (1) should be maintained
for proper performance of the wheelchair.
a. To adjust axle sleeve, you will need an
1 1/8" open end wrench to turn the outside axle
sleeve nuts (2).
b. You will also need a 3/4" wrench to hold the
axle sleeve in place while loosening or tighten-
ing the axle sleeve nuts.
c. Loosen nuts and adjust axle sleeve in or out to
desired location. Distance should be equal on
both axle sleeves.
E. CUSHION (OPTIONAL)
1. Installation
a. Place cushion on seat sling with
VELCRO® side down. The beveled
edge of the cushion should be in front.
b. Press firmly into place.
F. REAR AXLE ASSEMBLY
d. Hold axle sleeve with 3/4" wrench
and tighten nuts.
(Detail)
1
The most important adjustment on your Quickie All
Court is the position of your center of gravity.
3. Wheelbase Width Adjustment
9
4
Adjusting the wheelbase width allows the rider the
option to move the wheels closer or further away from
the hips.
The position of your seat frame will determine your
center of gravity.
2
1
• The further forward the seat, the more stable the
chair becomes.
Adjust the wheelbase width by:
• Moving the seat frame back will increase your
turning speed and lighten the front end.
a. Loosening the nut (2) and repositioning the
eccentric axle sleeve (1) into the threaded
camber tube.
For example: Using hole 1 will increase your
turning speed.
b. Retighten nuts.
NOTE– When making this adjustment refer to the toe-
Using hole 9 will give the rider
a more stable ride.
in and toe-out section.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
32
33
X . S e t - u p
&
A d j u s t m e n t
X . S e t - u p
&
A d j u s t m e n t
H. FOOTREST
4. Toe-in and Toe-out
Toe-in and Toe-out are terms that relate to how well
the rear wheels of the chair are aligned. This will
affect how well the chair will roll. Drag or resistance
occurs in a wheelchair when the rear wheels are not
properly aligned.
NOTE– Use a torque setting of 100 in./lbs. when
adjusting footplate.
1. Height Adjustment
a. Remove footrest bolt and slide footrest up or
down inside tube to correct position.
b. Tighten bolt securely.
Toe-in or toe-out can be slightly adjusted by adjusting
the eccentric axle sleeve.
2. Horizontal Adjustment
a. Loosen set screws at footrest receivers.
b. Slide footplate assembly to desired position.
c. Retighten screws.
5. Eccentric Axle Sleeve Adjustment
2° eccentric axle sleeves are standard on chair and are
used for toe-in toe-out adjustments. Refer to “Axle
Sleeve Adjustments” for tightening procedures.
Front of chair
Rear of chair
3. Footplate Angle Adjustment
a. Loosen flathead screws.
b. Reposition footplate to desired angle and
retighten screws.
a. To add 2° of camber:
1. Loosen axle sleeves.
2. Position axle sleeves with large lobes down (A).
b. To subtract 2° of camber.
1. Loosen axle sleeves.
2. Position axle sleeves with large lobes up (B).
c. Make sure both sleeves are aligned equally.
I. INTEGRAL 5TH WHEEL
The Match Point comes standard with the 5th
wheel. This increases rear stability.
Caster Height Adjustment for the Single Integral
5th wheel.
G. CASTER FORKS
The anti-tip height can be adjusted by repositioning
the spacers within the rear caster journal.
1. Caster Wheel Replacement
a. Loosen the bolt and remove the caster wheel and
the two washers.
A
B
Each caster journal is equipped with four 1/8" thick
spacers (1).
Single Integral 5th Wheel
b. Position new caster wheel into fork.
c. Carefully position washer on each side of
caster wheel.
a. To lower the casters remove desired spacers and
position them on the bottom of caster journal (2).
b. To raise the height of the caster remove desired
spacers and move to the top of the caster journal.
d. Insert bolt. Tighten securely.
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
34
35
X . S e t - u p
&
A d j u s t m e n t
X I . T r o u b l e s h o o t i n g
J. CHECK-OUT
You will need to adjust your chair from time to time for best performance (especially if
you alter the original settings). This chart gives you a first solution, then a second
and a third if needed. You may need to look farther to find the best solution for a spe-
cific problem.
After the wheelchair is assembled and adjusted, it
should roll smoothly and easily. All accessories should
also perform smoothly. If you have any problems, fol-
low these procedures:
NOTE– To keep track of your progress, make only ONE change at a time.
1. Review assembly and adjustment sections to
make sure chair was properly prepared.
2. Review troubleshooting guide.
3. If your problem persists, contact your authorized
Quickie supplier.
If you still have a problem after contacting your
authorized Quickie supplier, contact Sunrise
Medical Mobility Products customer service. See
the introduction page for details on how to con-
tact you authorized Quickie supplier or Sunrise
Medical Mobility Products customer service.
SO LUTIO NS
Make sure tire pressure is correct and equal in both rear tires and
front caster tires, if pneumatic.
ꢀ ꢀ ꢀ ꢀ
Make sure all nuts and bolts are snug.
ꢀ ꢀ ꢀ ꢀ
Make sure all spokes and nipples are tight on radial spoke wheels.
ꢀ
ꢀ
ꢀ
Use Tri-Flow Lubricant (Teflon®-based) between all modular frame
connections and parts.
Make sure both front casters touch the ground simultaneously. If
they do not, add the proper spacers between the bottom bearing of
the caster plate and fork stem nut until they do. Make sure you
check for this problem on a flat surface.
ꢀ
ꢀ ꢀ
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
36
37
X I I . M a i n t e n a n c e
X I I . M a i n t e n a n c e
C. MAINTENANCE TIPS
1. Axles & Axle Sleeves:
A. INTRODUCTION
1. Proper maintenance will improve performance and extend the useful life
of your chair.
2. Clean your chair regularly. This will help you find loose or worn parts and make
your chair easier to use.
Check axles and axle sleeves every six months to make sure they are tight. Loose
sleeves will damage the axle plate and will affect performance.
2. Tire Air Pressure:
3. Repair or replace loose, worn, bent or damaged parts before using this chair.
4. To protect your investment, have all major maintenance and repair work done by
your authorized Quickie supplier.
Check air pressure in pneumatic tires at least ONCE A WEEK. The wheel locks will not
grip properly if you fail to maintain the air pressure shown on tire sidewall.
D. CLEANING
1. Paint Finish
a. Clean the paint finish with mild soap at least once a month.
b. Protect the paint with a coat of non-abrasive auto wax every three months.
If you fail to heed these warnings your chair may fail and cause severe injury to the
rider or others.
2. Axles and Moving Parts
1. Inspect and maintain this chair strictly per chart.
a. Clean around axles and moving parts WEEKLY with a slightly damp (not wet) cloth.
b. Wipe off or blow away any fluff, dust, or dirt on axles or moving parts.
NOTE– You do not need to grease or oil the chair.
2. If you detect a problem, make sure to service or repair the chair before use.
3. At least once a year, have a complete inspection, safety check and
service of your chair made by an authorized Quickie supplier.
3. Upholstery
B. MAINTENANCE CHART
a. Hand-wash (machine washing may damage fabric).
b. Drip-dry only. DO NOT machine dry as heat will damage fabric.
E. STORAGE TIPS
CHECK...
1. Store your chair in a clean, dry area. If you fail to do so, parts may rust
or corrode.
Tire inflation level
ꢀ
2. Before using your chair, make sure it is in proper working order. Inspect and ser-
vice all items on the “Maintenance Chart.” (See p. 37)
3. If stored for more than three months, have your chair inspected by an autho-
rized Quickie supplier before use.
Wheel locks
ꢀ
All fasteners for wear and tightness
ꢀ
Axle and axle sleeves
ꢀ
Wheels, tires and spokes
ꢀ
Casters
ꢀ
Anti-tip tubes
ꢀ
Frame
ꢀ
Upholstery
ꢀ
Service by Authorized Q uickie Supplier
ꢀ
930469 Rev. A
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
38
X I I I . S u n r i s e L i m i t e d W a r r a n t y
A. FOR LIFETIME
Sunrise Medical warrants the frame and quick-release axles of this wheelchair against
defects in materials and workmanship for the life of the original purchaser.
The expected life of this frame is five years.
B. FOR TWO (2) YEARS
We warrant all Quickie-made parts and components of this wheelchair against defects
in materials and workmanship for two years from the date of first consumer purchase.
C. LIMITATIONS
1. We do not warrant:
• Tires and tubes, upholstery, armrests and push-handle grips.
• Damage from neglect, misuse or from improper installation or repair.
• Damage from exceeding weight limit of 250 pounds.
2. This warranty is VOID if the original chair serial number tag is removed or altered.
3. This warranty applies in the USA only. Check with your Quickie supplier to find
out if international warranties apply.
D. WHAT WE WILL DO
1. Our sole liability is to repair or replace covered parts. This is the exclusive
remedy for consequential damages.
E. WHAT YOU MUST DO
1. Obtain from us, while this warranty is in effect, prior approval for return
or repair of covered parts.
2. Return the wheelchair or part(s), freight pre-paid, to Sunrise Medical at: 2842
Business Park Avenue, Fresno, CA 93727-1328.
3. Pay the cost of labor to repair, remove or install parts.
F. NOTICE TO CONSUMER
1. If allowed by law, this warranty is in place of any other warranty (written or
oral, express or implied, including a warranty of merchantability, or fitness for a
particular purpose).
2. This warranty gives you certain legal rights. You may also have other rights that
vary from state to state.
Record your serial number here for future reference:
________________________
930469 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunrise Medical
Mobility Products Division
7477 East Dry Creek Parkway • Longmont, Colorado • 80503 USA
(800) 333-4000
In Canada (800) 263-3390
© 2001, Sunrise Medical 8.01
930469 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
|