PARTS AND OPERATION MANUAL
PORTO MIX
MINI CONCRETE MIXER
PLASTIC DRUM MODELS
SMC3PE AND SMC3PB
Revision #0 (08/08/03)
STOWCONSTRUCTIONEQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
PARTS DEPARTMENT:
800-427-1244
FAX: 800-672-7877
CARSON, CA 90749
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
310-537-3700 • 888-252-STOW [888-252-7869]
FAX:310-537-1986 • FAX:800-556-1986
E-MAIL: [email protected] • WWW: stowmfg.com
800-478-1244
FAX:310-631-5032
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT
800-478-1244
FAX: 310- 537-4259
TECHNICAL ASSISTANCE
800-478-1244
FAX: 310- 631-5032
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/09/02) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
STOW PORTO MIXER —
Portable Concrete Mixer
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation .................................... 8-10
Operation and Safety Decals ............................. 11-12
Specifications .......................................................... 13
Dimensions (Mixer) ................................................. 14
Dimensions (Electric Motor).................................... 15
General Information ................................................ 16
Mixer Components.................................................. 17
Basic Engine ........................................................... 18
Assembly Instructions ........................................ 19-20
Pre-Inspection (Gasoline Engine) ........................... 21
Initial Start-up (Electric Motor) ................................ 22
Initial Start-up (Gasoline Engine)....................... 23-24
Maintenance ...................................................... 25-27
Preparation for Long-Term Storage........................ 28
Troubleshooting (Engine)........................................ 30
Troubleshooting (Engine/Mixer) .............................. 31
Explanation Of Code In Remarks Column .............. 32
Suggested Spare Parts ........................................... 33
Nameplate and Decals....................................... 34-35
Mixer Assembly (Plastic Drum) .......................... 36-39
Terms and Conditions of Sale ................................. 40
Specification and part number
are subject to change without
notice.
PAGE 4 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealeraccountnumber
❒
❒
❒
❒
❒
❒
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number on
hand when calling.
Parts Department
Extra Discounts!
800-427-1244
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
All parts orders which include complete part numbers
and are received by our automated web parts order
system, or by fax qualify for the following extra
discounts:
Service Department
800-478-1244
310-537-3700
Fax:310-537-4259
Fax:310-537-1173
Fax:310-604-9237
Ordered
via
Standard
orders
Stock orders
($750 list and above)
Warranty Department
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax
3%
5%
10%
10%
Web
Sales Department
310-661-4242
877-289-7869 (877-BUY-STOW)
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other
carrier.
NOTE:DISCOUNTSARESUBJECTTOCHANGE
Direct TOLL-FREE access
to our Parts Department:
Toll-free nationwide — 800-427-1244
STOWCONSTRUCTIONEQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 888-252-STOW [888-252-7869]
FAX:310-537-1986 • FAX:800-556-1986
E-MAIL: [email protected] • WWW: stowmfg.com
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
Rotating Parts
This Owner's Manual has been
developed to provide complete
instructions for the safe and
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
efficient operation of the STOW
Models SMC3PE and SMC3PB
Portable Concrete Mixers.
Before using these mixers,
ensure that the operating
individual has read and
understands all instructions
in this manual.
Accidental Starting
ALWAYS place the circuit breaker or power
ON/OFF switch in the OFF position when the
pump is not in use.
SAFETY MESSAGE ALERT SYMBOLS
Sight and Hearing hazard
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
ALWAYS wear approved eye and hearing
protection.
DANGER: You WILL be KILLED or
SERIOUSLY injured if you do not follow
directions.
Respiratory Hazard
ALWAYS wear approved respiratory
protection.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you do not follow
directions.
Equipment Damage Messages
CAUTION: You CAN be injured if you
Other important messages are provided throughout this manual
to help prevent damage to your pump, other property, or the
surrounding environment.
do not follow directions.
Potential hazards associated with the STOW PORTO MIXER
operation will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
This mixer, other property, or the
surrounding environment could
be damaged if you do not follow
instructions.
PAGE 6 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF switch in
the OFF position, and remove the ignition key
when the machine is not in use.
ALWAYS wear approved respiratory
protection.
Equipment Damage Messages
Sight and Hearing hazard
Other important messages are provided throughout this manual
to help prevent damage to your mixer, other property, or the
surrounding environment.
ALWAYS wear approved eye and hearing
protection.
This mixer, other property, or the
surrounding environment could
be damaged if you do not follow
instructions.
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
NEVERtouchthehotexhaustmanifold,
muffler or cylinder.Allow these parts to
cool before servicing engine or mixer.
DANGER:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only!This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating the Porto Mixer:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
GENERAL SAFETY
■
DO NOT operate or service this equipment before
readingthisentiremanual.
The engine of this mixer requires an adequate free flow of
cooling air. NEVER! operate the mixer in any enclosed or
narrow area where free flow of the air is restricted. If the air
flow is restricted it will cause
■
■
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-
toed boots and other protective devices required
by the job.
serious damage to the
mixer or engine and may
cause injury to people and
property. Remember the
mixer's engine (gasoline
models only) gives off
DEADLY gases.
■
■
NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
NEVER operate this equipment under the
influence or drugs or alcohol.
and open flames.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■
NEVER operate the mixer in an explosive
atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
ALWAYS check the machine for loosened threads or bolts
before starting.
ALWAYS wear proper respiratory (mask) hearing and eye
protection equipment when operating the mixer.
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.
Refer to the Engine Owner's Manual for engine technical
questions or information.
■
■
NEVER use accessories or attachments, which are not
recommended by STOW for this equipment. Damage to the
equipment and/or injury to user may result.
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
PAGE 8 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
■
■
■
NEVER Run engine without air cleaner. Severe engine
■
■
High Temperatures – Always stop engine and allow the
engine to cool before adding fuel, oil or performing service
and maintenance functions. Contact with hot components can
cause serious burns.
damage may occur.
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using roller.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■
■
If mixer is equipped with an electric motor, operate only at
120VAC, 60 Hz.
■
■
■
■
NEVER leave the mixer unattended, turn off engine or electric
motor when unattended.
Make sure the OFF/ON power switch is always in the OFF
position before inserting the mixer's power plug into an AC
receptacle (electric model only).
CAUTION must always be observed while servicing this mixer.
Rotating parts can cause injury if contacted.
Unauthorized equipment modifications will void all
warranties.
Maintenance Safety
■
NEVER lubricate components or attempt service on a running
machine.
Ensure that any trailing cable is protected against damage
and not liable to be tripped over or trapped underneath the
mixer.
■
ALWAYS allow the machine a proper amount of time to cool
before servicing.
■
■
Ensure any extention cables must be no longer than 30 meters
(100 feet) in length and that the wire section is 2.5 mm 2.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts, or missing decals.
DO NOT allow extension cord to come into contact with water
or fluids.
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■
■
■
DO NOT spray water onto electric motor.
DO NOT expose power tools to rain or wet conditions.
DO NOT use food or plastic containers to dispose of
hazardous waste.
This mixer is intended for the production of concrete, mortar
and plaster. Mixer must be used only for its intended purpose.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
■
This mixer is not suitable for the mixing of flammable or
explosive substances.
■
■
NEVER operate the mixer in an explosive atmosphere.
Before starting the mixer, check that all guards are in position
and correctly fitted.
■
■
DO NOT tip mixer onto drum mouth when the motor is running.
Keep area around the mixer clear of obstructions which
could cause persons to fall onto moving parts.
■
■
ALWAYS ensure mixer is on level ground before mixing.
Become familiar with the controls of the machine before
operating.
■
■
ALWAYS replace any worn or damaged warning decals.
Ensure the drum is rotating while filling and emptying the
drum.
■
ALWAYS disconnect AC power plug from power source
before moving mixer (electric model only).
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Emergencies
■
ALWAYS know the location of the nearest fire extinguisher.
■
■
ALWAYS know the location of the nearest first aid kit.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
PAGE 10 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND SAFETY DECALS
Machine Safety Decals
The STOW PORTO MIXER is equipped with a number of safety decals. These decals are provided for operator safety and
maintenance information.The illustration below and on the next page shows these decals as they appear on the machine.Should
any of these decals become unreadable, replacements can be obtained from your dealer.
P/N: DCL300
(Decal is Molded Into Tub)
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND SAFETY DECALS
WARNING!
1. Read owner’s manual before operating mixer.
ADVERTENCIA!
1. Lea el manual de operació antes de usar la mezcladora.
AVERTISSEMENT!
1. Lisez le manual d’ utilisation avant d’ utiliser le le malaxeur.
2. Keep unauthorized and untrained people away
from mixer during operation.
3. Make sure all safety devices (guards) are in place
before mixer is started.
2. Mantenga personas que no estén autorizadas o capacitadas
alejades de la mezcladora durante el funcionamiento de la
máquina.
2. Seul un personnel qualifié peut être authorisé à se trouver à proximité
du malaxeur quand il est en opération.
3. Assurez vous que tous les dispositifs de sécurité sont en place avant
de mettre le malaxeur en marche.
3. Asegúreseque todos los aparatos de seguridad estén
trabajando apropiadamente antes de usar la mezcladora.
4. Keep hands and fingers away from moving objects.
4. Gardez les mains et doigts loin de toute piè en mouvement.
4. Mantenga las monos y dedos alejados de objetos en moviminto.
5. NEVER leave mixer unattended when operating.
6. ALWAYS check V-belt before starting mixer.
5. NE LAISSEZ jamais le malaxeur sans surveillance quand il est en
opération.
5. NUNCA se aleje de la mezclaora mientras ésta, este trabajando!
6. SIEMPRE inspeccione la banda antes de encender la mezcladora. 6. VEUILLEZ toujours vérifier la courroie avant de mettre le malaxeur
en marche.
GASOLINE ENGINE
Make sure engine is turned off and spark plug wire is
disconnected before cleaning mixer.
MOTEUR À ESSENCE
Assurez vous que le moteur est arrêté et que le fil de la bougie est
débranché avant de nettoyer le malaxeur.
MÁQUINAS DE GASOLINA
Asegure que la máquina este apagada y el alambre de la bujía
este desconectado antes de empezar a limpiar la mezcladora.
N’ UTILISEZ pas le malaxeur dans un endroit fermé, il est nécessaire
de travailler dans un endroit avec une bonne aération.
DO NOT operate mixer in an enclosed area, proper
ventilation is required.
NO encienda la mezcladora en una área cerrada; es necesario
estar en una área que tenga apropiada ventilación.
VEUILLEZ toujours vé la courroie avant de mettre le malaxeur en
marche.
ALWAYS stop the engine and allow engine to cool before
adding fuel or oil.
SIEMPRE apague la máquina y permita que se enfrie antes de
ponerle gasolina o aceite.
VÉRIFIEZ toujours le niveau d’essence et d’huile ainsi que le filtre à
air avant de mettre le moteur en marche.
ALWAYS check fuel, oil and air filter before starting engine.
SIEMPRE revise la gasolina, aceite, y el filtro del air antes de
encender la máquina.
ELECTRIC MOTOR
Make sure power cord has been disconnected from power
source before cleaning mixer.
MOTOR ELÉCTRICO
Asegúrese que el cable de corriente esté de empezar a limpiar
la mezcladora.
MOTEUR ÉLECTRIQUE
Assures vous toujours que le cable a été débranché de la prise de
courant avant de nettoyer le malaxeur.
Este motor elétrico está solamente capacitado para corriente
alterna de 115 voltios.
This electric motor is for 115 VAC operation only.
Ce moteur électrique à été conçu pour opération à 115 volts seulement.
ALWAYS use an extension cord of proper size, see chart
below:
SIEMPRE use el tamaño de extensiones de alambre indicado
como muestra el diagrama abajo:
Il faut toujours utiliser une rallonge de taille appropriée, veuillez s’il vous
référer au diagramme suivant:
TAMAÑO DE EXTENSIÓN
TAILLE DE LA RALLONGE
EXTENSION CORD SIZE
Alambre
Alambre
Numéro 6
Cable
Cable
Cable
Cable
Numéro 6
Alambre
Numéro 12
Alambre
No. 12 Wire
No. 10 Wire
No. 6 Wire
200 feet
No. 8 Wire
Numéro 10
Numéro 12
Numéro 10
Numéro 8
Numéro 8
75 feet
50 feet
100 feet
200 pies
75 pies
100 pies
50 pieds
50 pieds
50 pies
50 pieds
50 pieds
(22.86 meters)
(15.24 meters)
(30.48 meters) (60.96 meters)
(22.86 metros) (30.48 metros) (60.96 metros)
(15.24 métres)
(15.24 métres)
(15.24 métres) (15.24 métres)
(15.24 metros)
REMOVE BOLT AND FILL
WITH EP. 90 GEAR OIL
NEVER! OPERATE MIXER WITH
V-BELT COVER REMOVED.
ELECTRIC
MOTOR
REMOVER EL TORÑILLO Y
LLENAR CON ACEITE DE
ENGRNAJE EP. 90
NUNCA! MANEJE LA MEZCLADORA
SIN LA COBERTURA DE BANDA-V
REMOVIDA.
MOTOR
ELÉCTRICO
ELECTRIC
MOTOR
MOTEUR
ÉLECTRIQUE
ÔTEZ LE BOULON ET
REMPLISSEZ AVEC DE I’HUILE
EP. 90 À ENGRENAGES
N’ UTILISEZ! JAMAIS LE MALAXEUR
SANS LE COUVERCLE DE LA COURROIE.
MOTOR
ELÉCTRICO
MOTEUR
ÉLECTRIQUE
CHECK DAILY
REVISAR DIARIO
VÉRIFIEZ QUOTIDIENNEMENT
DCL250
P/N DCL250
PAGE 12 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— SPECIFICATIONS
Table 1. Specifications (Engine & Electric Motor)
Model
BRIGGS & STRATTON 91200
BALDOR 17LYE304
4-stroke, Vertical valve, Single
Cylinder
3/4 HP, 120 VAC, Single
Phase Electric Motor
Type
2.56 in. x 1.75 in.
(65.1 mm x 44.4 mm)
Bore X Stroke
N/A
Displacement
9.0 cu. in. (148 cc)
3.5 HP at 3,600 R.P.M.
1,800 100 R.P.M.
N/A
3/4 H.P./3,450 RPM
N/A
Max Output
Engine/Electric Motor
Standard Idle Speed
Approx. 0.5 U.S. Gallons
(1.89 Liters)
Fuel Tank Capacity
N/A
Fuel
Unleaded Gasoline
2 U.S. Quarts (1.89 Liters)
Centrifugal Fly-weight Type
Recoil Start
N/A
N/A
N/A
N/A
Lube Oil Capacity
Speed Control Method
Starting Method
12.5 x 11.47 x 12.18 in.
(317.5 x 291.4 x 309.4 mm)
11.75 x 6.0 X 8.0 in.
(298 X 152 X 203 mm)
Dimensions (L x W x H)
Dry Net Weight
20.3 lbs (9.2 kg)
Approx. 12 lbs. (5.4 Kg.)
Table 2. Porto Mixer Specifications
Height
34 in. (863.6 mm)
Width
23-5/8 in. (584.2 mm)
48-1/2 in. (1,219.2 mm)
35 lbs. (15.9 Kg)
Length
Stand Weight
Maximum Drum Capacity
4.5 cu. ft. (0.13 m3)
3.0 cu. ft. (0.08 m3)
129 lbs. (58.5 Kg)
138 lbs. (62.6 Kg)
Maximum Mixing Capacity (1/2 bag)
Unladen Weight - Electric Motor
Unladen Weight - Gasoline Engine
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— DIMENSIONS (MIXER)
PAGE 14 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— DIMENSIONS (ELECTRIC MOTOR)
Figure 2. Electric Motor
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— GENERAL INFORMATION
PORTABLE GENERATORS
APPLICATION
This mixer is only intended for the production of concrete
and mortar. The mixer must be used for its intended
purposes and is not suitable for the mixing of flammable or
explosive substances. The mixer must not be used in an
explosive atmosphere.
When using a portable generator it must have a minimum
output of 2.5 kw and be continuous rated.
GEARBOX
The gearbox oil level has been preset at the factory prior to
shipping. Before inspecting the gearbox oil level (Figures 30
and 31), make sure the gearbox is cold before removing the
filler plug. Fill up with EP90. or similar gear oil.
POWER PLANTS
This portable mixer is powered by either a Briggs and Stratton
4-stroke, verticle valve, single cylinder, gasoline engine rated
at 3.5 hp @3,600 rpm. or a 0.75 hp electric motor.
TRANSPORTINGTHE MIXER
Use a ramp (Figure 3) to load and unload the mixer from the
transport vehicle. Never drop the mixer onto the ground; damage
to the mixer could result.
DRUM ASSEMBLY
The drum is instantly removable by unscrewing counter-
clockwise. When inserting drum onto gearbox shaft, make sure
that drum is fully screwed onto shoulder or threads may be
damaged. Use extreme care when screwing on the drum,
spinning drum onto the gearbox shaft too fast may damage
gearbox.
ELECTRICAL
If mixer is equipped with an electric motor, make sure that
the power being supplied to the motor corresponds to the
voltage rating label on the motor.Supplying the wrong voltage
to the electric motor will cause severe electrical damage to
the motor.
Always make sure that OFF/ON switch on the electric motor
is in the OFF position before applying power.
It is strongly recommended that when plugging in the
mixer's power cord into a receptacle, that a G.F.C.I.(Ground
Fault Current Interrupter) receptacle be used.
EXTENSION CABLES
The extension cable should be a 3-wire configuration that
includes a ground wire that conforms to UL code. The wire
cross section must be a minimum of 2.5 mm2 . Choose an
extension cord of adequate current carrying as Reference in
Table 5. Remember distance affects the wire size of the
extension cable.
Ensure that the extension cable is carefully laid out avoid-
ing wet areas, sharp edges and locations where vehicles
might run over it. Avoid allowing the extension cable to be
trapped underneath the mixer.
Unroll the extension cable fully or it will overheat and could
catch fire. Make sure that all extension cable connections
are dry and safe. Replace any defective or badly worn ex-
tension cable immediately.
Figure 3. Mixer Loading
PAGE 16 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— MIXER COMPONENTS
Figure 4 shows the basic components of the STOW Porto
Mixer.
Figure 4. Mixer Components
Table 3. MIXING HINTS
BATCH QUANTITIES
APPROX. BATCH
OUTPUT
MIX
RATIOS
CEMENT 112 lbs.
SAND
CU. FT.
STONE
CU. FT.
APPLICATIONS
(50 Kgs.)
Bag
LTR
35
LTR
71
CU. FT.
3
LTR
85
1:2:4
1:3:6
1:4:8
1/2 BAG
1/3 BAG
1/4 BAG
1-1/4
1-1/4
1-1/4
2-1/2
2-1/2
2-1/2
Most Ordinary
Foundations
35
71
2-3/4
2-3/4
78
35
71
78
Rough Mass
Concrete
1:1-1/2:3
2/3 BAG
1-1/4
35
3
71
3
85
Watertight Floors,
Tanks, Pits, Etc.
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— BASIC ENGINE
Figure 5. Engine Controls and Components
INITIAL SERVICING
6. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
The engine (Figure 5) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions and details of operation and servicing.The
engine shown above is a Briggs and Stratton engine, operation
for other types of engines may vary somewhat.
7.
Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely.DO NOT over fill.
Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
allow dirt to enter the engine,
causing rapid engine wear.
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT
8.
Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
attempt to start the engine until the fuel residue has been completely
wiped up, and the area surrounding the engine is dry.
9. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.024 - 0.028 inch) Clean
spark plug once a week.
2. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
10. Muffler - Used to reduce noise and emissions.
3. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
WARNING
4. Oil Drain Plug – Remove this plug to remove oil from the
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
engine's crankcase.
5. Dipstick/Oil Filler Cap – Remove this cap to determine if
the engine oil is low. Add oil through this filler port as
recommended in Table 4.
PAGE 18 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— ASSEMBLY INSTRUCTIONS
Assembly
1. Removethemixerdrum andassociatedcomponentsfrom
the packing container (Figure 6). Match the components
againstthepartslisttomakesurethattheyareallaccounted
for.
Figure 6. Packing Container
Figure 8. Mixing Drum Placement
2. Placethemixerframeonasecurelevelsurface,andattach
the top cover as shown in Figure 7.
4. Place the two halves of the optional support stand together
(Figure9).Theleftsupportstandfitsintothecenterbosson
therightsupportstand.
5. InserttheadapterpinthroughbossesasshowninFigure9.
Oncetheadapterpinhasbeeninsertedandaligned, insert
the locking pin. Place the round part of the locking pin over
the bottom section of the adapter pin.
Figure 7.Top Cover Placement
3. Fit the mixing drum onto gearbox shaft as shown in Figure
8.Rotatedruminaclockwisedirection,makesurethedrum
fits right up to the shoulder on the gearbox shaft.
CAUTION
Figure 9. Optional Support Stand
DO NOT spin the drum on fast, as this may
damage the gearbox.
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— ASSEMBLY INSTRUCTIONS
6. Tip mixer onto mouth as shown in Figure 10, and insert
support stand into frame swivel point.
9. Before attempting to lift mixer, locate the frame locking clip.
AttachthelockingclipasshowninFigure12.Thiswillprevent
the mixing drum from moving when the mixer is positioned
in an upright position.
Figure 12. Frame Locking Clip
10. DO NOT tilt the mixer on a wet, smooth or slippery surface.
Figure 10. Attaching Support Stand
7. Removebothwheelsandwheelretainersfromthepacking
container.
8. Placeonewheeloneachsideof themixer'saxleasshown
in Figure 11. Position washer over axle to secure wheel in
place. Insert cotter pin to lock wheel in place.
Figure 13. Slippery or Wet Surfaces
11. Oncethestandhasbeenassembled,andthelockingcliphas
been secured, begin tilting the mixer to an upright position.
Remember always tilt from the front of the mixer as shown
in Figure 14.
Figure 11.Wheels and Wheel Retainers
Figure 14.Tilting Mixer to Upright Position
PAGE 20 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— PRE-INSPECTION (GASOLINE ENGINE)
3. Insertandremovethedipstickwithoutscrewingitintothefiller
CAUTION
neck. Check the oil level shown on the dipstick.
NEVER operate the mixer in
a confined area or enclosed
area structure that does not
provide ample free flow of air.
4. Iftheoillevelislow(Figure16), filltotheedgeoftheoilfiller
holewiththerecommendedoiltype(Table4).Maximum oil
capacity is 0.48 quarts (.45 liters)
ALWAYS wear approved eye and hearing
protection before operating the mixer.
NEVER place hands inside drum while the
engine is running.ALWAYS shut the engine
down before performing any kind of
maintenance service on the mixer.
Figure 16. Engine Oil Dipstick (Oil Level)
Table 4. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
Before Starting
1.
2.
Read safety instructions at the beginning of manual.
Clean the mixer, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
0°C or Lower
3.
4.
5.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
Check carburetor for external dirt and dust. Clean with dry
compressed air.
Explosive Fuel
Check fastening nuts and bolts for tightness.
Fuel Check
Engine Oil Check
Motor fuels are highly flammable and can be dangerous if
mishandled. DO NOT smoke while refueling. DO NOT attempt
to refuel the mixer if the engine is hot! or running.
1.
To check the engine oil level, place the mixer on secure
level ground with the engine stopped.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 15) and wipe clean.
1. Remove the gasoline cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
V-Belt Check
A worn or damagedV-belt can adversely affect the performance
of the mixer.If aV-belt is defective or worn simply replace the V-
belt as outlined in the maintenance section of this manual.
Figure 15. Engine Oil Dipstick (Removal)
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— INITIAL START-UP (ELECTRIC MOTOR)
5. Plug the other end of the extension cord into a 120 VAC
G.F.C.I.protected receptacle. Rememberthepowerrequire-
ments for this electric motor is 120VAC, 60 Hz. The use of
any other input voltage will severely damage the motor.
Initial Start-up Instructions (Electric Motor)
Starting
CAUTION:
DO NOT attempt to operate the mixer until the
Safety, General Information and Inspection
sections have been read and understood.
WARNING:
ALWAYS read the label on the electric motor
before applying power. The label will indicate
the proper power requirements for the motor.
Remember the use of any other input voltage
will severely damage the motor.
1. Before starting, make sure mixer is positioned on a secure
flatsurfacetopreventtipping.
2. Use an extension cord (see Table 5) of adequate current
carryingcapacity,insert theelectricmotor'spowerplug into
one end of the extension cord.
WARNING:
To prevent tripping (Figure 18) of both the mixer
and personnel, position the extension cord so
that it lays flat and is not curled underneath the
mixer.
3. NEVER! use a worn or frayed extension cord.
4. NEVER! operate mixer withV-belt cover removed.
Table 5. Extension Cord Size
No. 12 Wire
No. 10 Wire
No. 8 Wire
No. 6 Wire
50 (feet)
75 (feet)
100 (feet)
200 (feet)
(15.24 meters) (22.86 meters (30.48 meters (60.96 meters
Figure 18. Mixer (Tripping)
DANGER
6. Thedrumshouldberotatingallowing themixingprocess to
begin. Use a shovel (Figure 19) to place the cement mix
inside the drum, add water as required. Be careful to only
placethetipoftheshovelinsidethedrum.Placingtheshovel
allthewayinsidethedrumwillcausetheshoveltostrikethe
blades. Thisconditionwillmaketheshovelrotate,andcould
cause injury to personnel.
NEVER! touch the power cord (Figure 17)
with wet hands or while standing in water
when it is connected to a power source.The
possibly exists of electrical shock
(electrocution) even death. NEVER! spray
water directly on the electric motor.
WET
HANDS
POWER
CORD
(POWER ON)
Figure 19. Mixing Drum (Placing Cement Mix)
6. SeeTable3formixinghints.NEVER!placehandsinsidethe
Figure 17. Extension Cord (Wet Hands)
drum while the drum is rotating.
PAGE 22 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— INITIAL START-UP (GASOLINE ENGINE)
4. Grasp the starter grip (Figure 23) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
sponding to the compression point. PULL the starter grip
briskly and smoothly for starting.
DO NOT attempt to operate the mixer until
the Safety, General Information and
Inspection sections of this manual have
been read and thoroughly understood.
This section is intended to assist the operator with the initial
start-up of the walk-behind trowel. It is extremely important that
this section be read carefully before attempting to use the trowel
in the field.
Starting the Engine (BRIGGS & STRATTON)
1. Placethechoke lever(Figure21)intheCHOKE (CLOSED)
position if starting a cold engine.
Figure 23. Starter Grip
7. Iftheenginehasstarted,slowlyreturnthechokelever tothe
RUN (OPEN) position if needed (Figure 24 ). If the engine
has not started repeat steps 1 through 4.
Figure 20. Engine Choke Lever (Closed)
2. Place the choke lever (Figure 20) in the RUN (OPEN)
position if starting a warm engine engine or if the
temperature is warm.
Figure 24. Engine Choke Lever (Closed)
8. Beforethemixerisplacedintooperation,runtheenginefor
several minutes. Check for fuel leaks, and noises that
would associate with a loseV-belt cover or component.
Figure 21. Engine Choke Lever (Open)
9. To begin mixing, place the throttle lever (Figure 25) in the
3. Placethethrottlelever(Figure22)inthe"TURTLE" (IDLE)
"RABBIT" (FAST) position
position.
Figure 22. Throttle Lever (Idle Position)
Figure 25. Throttle Lever (Fast Position)
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— INITIAL START-UP (GASOLINE ENGINE)
Stopping The Engine
Normal Shutdown
1. Move the throttle lever to the "TURTLE" (IDLE) position
(Figure26)andruntheengineforthreeminutesatlowspeed.
Figure 26. Throttle Lever (Idle Position)
2. Aftertheenginecools,movethethrottlelever tothe STOP
position (Figure 27).
Figure 27. Throttle Lever (Stop Position)
Emergency Showdown
1. Move the throttle lever quickly to the OFF position (Figure
28).
Figure 28. Throttle Lever (Stop Position)
PAGE 24 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— MAINTENANCE
Maintenance
5. Insert oil filler plug and tighten.
Gearbox Oil Check
1. Positionthe mixeronalevel surface and place asupport block
under thefrontofthemixer frameas showninFigure29.This
will level the mixer.
2. NEVER! check the gearbox oil level with the mixer tilted up or
down.ALWAYS check the gearbox oil level with the mixer in a
level position.
Figure 30. Gearbox Oil Level Check
V-Belt Check
1. To adjustV-belts, removeV-belt cover and loosen the main
motor mount bolts (Figure 31), raise electric motor and
retighten bolts. Belt tension should be adjusted so that the
maximum deflection is approximately 3/8 inch (10 mm).
2. ReplaceV-beltcover.
Figure 29. Mixer Positioning (Gearbox Oil Level)
CAUTION :
Figure 31. V-belt Adjustment
Gerarbox Removal
Check the gearbox oil level monthly before
operating mixer. Low oil level or no oil will
severely damage gearbox.
1. Remove drum by turning counter-clockwise to release from
gearboxshaft.
3. Beforeinspectingthegearboxoillevel,makesurethegearbox
iscoldbeforeremovingthefillerplug.Hot!oilcanburnskinand
cause injury.Let oil cool before checking.
2. Remove pulley, remember the nut securing the pulley is
left-handthreaded.Removecirclip, anddrawoutshaft.
3. Remove the 5 bolts securing rear plate.
4. Removegearboxoilfillerplug (Figure30)andfillwithEP90or
similargearoiltothelevelofthefillerplug.Replacegearboxoil
every 3,000 hours. Gerabox oil capacity is 8-10 ounces.
4. Reassembleinreverseorder,takingcaretoensuregearteeth
aremeshedcorrectly.
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— MAINTENANCE (GASOLINE ENGINE)
Table 6. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the BRIGGS AND STRATTON Shop Manual for service procedures
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
Reference manufacturer engine
manual for specific servicing
instructions.
PAGE 26 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— MAINTENANCE (GASOLINE ENGINE)
DANGER :
Maintenance
Perform the scheduled maintenance procedures as definded by
Table 6 and below:
DO NOT use gasoline as a cleaning solvent,
because that would create a risk of fire or
explosion.
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
gearbox for oil leaks. Repair or replace as needed.
ENGINEAIRCLEANER
1. Remove the air cleaner cover and foam filter element as
shown in Figure 34.
WEEKLY
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
2. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 32), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
Figure 32. Spark Plug Gap
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 33.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 4. Engine oil capacity is .48 quarts (0.45 liters).
DO NOT overfill.
Figure 34. Engine Air Cleaner
4. Install drain bolt with sealing washer and tighten securly.
Figure 33. Engine Oil (Draining)
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— PREPARATION FOR LONG -TERM STORAGE
Mixer Storage
For storage of the mixer for over 30 days, the following is
recommended:
z
Drain the fuel tank completely, or add STA-BIL to the
fuel.
z
z
Run the engine until the fuel is completely consumed.
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
z
z
Clean the entire mixer and engine compartment.
Cover the mixer and place it a clean dry area, that is
protected from harsh elements.
PAGE 28 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to start
POSSIBLE PROBLEM
SOLUTION
Ignition plug being bridge?
Carbon deposit at ignition?
Check ignition system.
Clean or replace ignition.
Replace insulators.
Fuel is available but spark plug
will not ignite. (Power available
at high tension cable).
Short circuit due to defective
insulators?
Improper spark gap?
Set spark plug gap to the correct gap.
Check stop switch circuit. Replace stop switch if defective.
Replace ignition coil.
Short circuit at stop switch?
Ignition coil defective?
Fuel is available but spark plug
will not ignite. (Power NOT
available at high tension cable).
Muffler clogged with carbon
deposits?
Clean or replace muffler.
Fuel is available and spark plug
ignites (compression normal).
Fuel in use inadequate (water,
dust)?
Flush fuel sytem and replace with fresh fuel.
Air Cleaner clogged?
Defective cylinder head gasket?
Cylinder worn?
Clean or replace air cleaner.
Tighten cylinder head bolts or replace head gasket.
Replace cylinder.
Fuel is available and spark plug
ignites (compression low ).
Spark plug loose?
Tighen spark plug.
Operation not satisfactory
Air cleaner clogged?
Air in fuel line?
Bleed (remove air) from fuel line.
Adjust carbureator float
Not enough power available
(compression normal, no miss-
firing).
Fuel level in carbureator float
chamber improper?
Carbon deposits in cylinder?
Ignition coil defective?
Clean or replace cylinder
Flush fuel sytem and replace with fresh fuel.
Replace ignition wires, clean ignition.
Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss-
firing).
Ignition plug often shorts?
Fuel in use inadequate (water,
dust)?
Excessive carbon depostion in
combustion chamber?
Clean or replace crankcase.
Clean or replace muffler.
Engine overheats.
Exhaust or muffler clogged with
carbon.
Spark plug heat value incorrect? Replace spark plug with correct type spark plug.
PAGE 30 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— TROUBLESHOOTING (ENGINE/MIXER)
TABLE 7. ENGINE TROUBLESHOOTING (Continued)
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Operation not satisfactory
Governor adjustment improper?
Governor spring defective?
Fuel flow erratic?
Adjust governor to correct lever.
Clean or replace ignition.
Check fuel line.
Rotational speed fluctuates.
Air taken in through suction
line?
Check suction line.
Dust in rotating part?
Spring spring failure?
Clean recoil starter assembly.
Replace sprial spring.
Recoil starter not working
properly.
TABLE 8. MIXER TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Check that the gears and bearings are not worn . Replace as
necessary.
Defective gearbox?
Drum rotates rough.
Worn V-belt?
Loose pulley?
Replace V-belt.
Tighten or replace pulley.
Incorrect or no voltage being
supplied to electric motor?
Check that the electric motor has the correct supply voltage.
Inspect power source and extension cord. Push reset button on
electric motor.
Power to electric motor?
Fuel?
Check level of fuel in fuel tank. Add fuel if necessary. Make sure
fuel is being supplied to the engine. Check to ensure that the fuel
filter is not clogged.
Drum does not rotate at all.
Broken V-belt?
Replace V-belt.
Check that the gears and bearings are not broken. Replace as
necessary.
Defective gearbox?
Defective motor?
Replace motor.
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER— EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
The contents of this parts
catalog are subject to change
without notice.
NOTE
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+
, %, or
*
■
Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.
If more than one of the same
NOTE
reference number is listed, the
last one listed indicates newest
(or latest) part available.
PAGE 32 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER — SUGGESTED SPARE PARTS
STOW PORTO MIXER 1 TO 3 UNITS
1 to 3 Units
Qty.
P/N
Description
2 ............ DM1840 ................ V-BELT, A23 (ELECTRIC MOTOR)
2 ............ MS-01 ................... V-BELT, A24 (GASOLINE)
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
PAGE 34 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NAMEPLATE AND DECALS.
NO
PART NO
PART NAME
QTY.
REMARKS
1
2
3
DCL300
DECAL:WARNING STOW
DECAL: STOW PORTO MIX ..................... 1 ............ INCLUDED WITHTUB
DECAL: NAMEPLATE ............................... 1 ............ CONTACT MQ PARTS DEPT.
1
4
DCL250
DECAL:WARNING MAINTENANCE
1
SEE DECAL ILLUSTRATIONS ON PAGES 11 AND 12.
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER — MIXER ASSY. (PLASTIC DRUM)
MIXER ASSY. (PLASTIC DRUM)
PAGE 36 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER — MIXER ASSY. (PLASTIC DRUM)
MIXER ASSY. (PLASTIC DRUM)
NO.
1#
2#
3#
4#
5#
6#
7
9#
10#
11
12
13
14
15
16
17
18#
19#
20#
21#
22#
23#
24
25
26
26A
26B
27
PART NO.
DM3150
DM1356
DM1912
DM355
PART NAME
QTY.
REMARKS
HEX HEAD BOLT M12 x 70
OIL FILLER PLUG M14 x 2 x 15L
HEX NUT M10
HEX HEAD BOLT M8 x P1.25 x 24L
FLAT WASHER M12
HEX NUT M12
TOGGLE SWITCH
GEAR BOX BACK COVER
GEAR BOX SEAL
1
1
2
3
2
1
1
1
DM3151
DM3152
SP9012
DM1320
DM1357
DM1380
DM1821
DM1822
DM2020
DM1840
DM1332
DM1810
DM1353
DM1352
DM1331
DM1310
DM1351
DM1333
DM1351
DM1741
DM1730
DM1740
DM1742
DM1641
DM2021
DM1911
DM1141
BELT GUARD
1
DRIVE PULLEY........................................ 1 ......... ELECTRIC MOTOR ONLY
SET SCREW M6 x 12L
BOLT M6 x 18
V-BELT, A23 ............................................. 1 ......... ELECTRIC MOTOR ONLY
NUT M12
GEARBOX PULLEY
OIL SEAL 20 x 42.5 x 10
BEARING RACE 6004
WORM GEAR
GEARBOX CASE
BEARING RACE 6006
GEAR & SHAFT
BEARING RACE 6006
WASHER
WHEEL, PNEUMATIC
AXLE
COTTER PIN
HEX NUT M8
NUT
HEX HEAD BOLT M10 x P1.5 x 40L
DRUM LOCK
1
2
1
1
1
1
1
1
1
1
1
2
2
1
2
2
2
3
1
28
29
30
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER — MIXER ASSY. (PLASTIC DRUM)
MIXER ASSY. (PLASTIC DRUM)
PAGE 38 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW PORTO MIXER — MIXER ASSY. (PLASTIC DRUM)
MIXER ASSY. (PLASTIC DRUM)
NO.
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49#
50
51
52
53
54
55
56
PART NO.
DM1527
DM1524
DM1510
DM1531
DM1613
DM1630
DM1631
DM1632
DM1620
DM1640
DM1221
DM1212
DM1213
DM1231
DM3050
DM3051
DM3000
912321040E1
DM1358
34579
PART NAME
QTY.
12
12
1
REMARKS
HEX NUT M10
BOLT
PLASTIC BARREL
BLADE, BARREL
HANDLE GRIP, RUBBER
TOP COVER CLAMP
SCREW 5.5 x 25
2
2
2
2
2
1
2
1
1
1
1
4
4
1
LOCKWASHER
TOP COVER, PLASTIC
BOLT M8 SPECIAL DOME HEAD
STAND, ADAPTER
STAND, BOTTOM LH (2 BOSS)
STAND, BOTTOM RH (1 BOSS)
CLIP LINCH PIN
NUT M8BOLT M8 x 35
BOLT M8 x 35
ENGINE MOUNT (GASOLINE)
ENGINE, 3.5 HP BRIGGS & STRATTON 1
RETAINER RING
MOTOR, ELECTRIC 3/4 H.P.
GEARBOX ASSEMBLY............................ 1 ......... INCLUDES ITEMS/#
V-BELT, A24 ............................................. 1 ......... GASOLINE ENGINE ONLY
DRIVE PULLEY........................................ 1 ......... GASOLINE ENGINE ONLY
MOUNTING PLATE
SEAL, OIL
1
1
DM1300
MS01
EM901006
DM1521
DM1354
DM1105
1
1
1
MAIN FRAME
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: July 15, 2003
TERMS AND CONDITIONS OF SALE — PARTS
Terms and Conditions of Sale
STOW Construction Equipment
DROP SHIPMENTS
PAYMENT TERMS
Terms of payment for unit sales are 2% 15
days net 30 days from date of invoice unless
otherwise specifically stated on our invoice.
Parts invoices have terms of net 10 days.
Minimum parts billing is $15.00 net.
Applicable discounts will be computed on
merchandise value only. Late charges will be
assessed at prevailing rates. Cash discounts
cannot be taken on current billings if any
previously billed amounts are past due.
STOW reserves the right to refuse Drop
Shipments outside the normal service area of
the purchasing dealer.
The sender will be notified of any material
received that does not meet the above
provisions. Such material will be held for 30
days from notification pending instructions. If a
reply is not received within 30 days, the material
will be returned to the sender at his expense
with no credit issued.
FIELDWAREHOUSES
Field Warehouses are currently located in
California, Georgia, Idaho, Iowa, and New
Jersey
PRICING, REBATES AND
SPECIFICATIONS
Every effort will be made to provide adequate
notice of changes; however, prices and
equipment specifications are subject to change
without notice.
SPECIAL EXPEDITING SERVICE
The higher of a $35.00 surcharge or actual
costs will be added to the invoice for special
handling, including bus shipments, or in cases
where STOW personnel must personally deliver
the equipment or parts to the carrier.
FREIGHT POLICY
Freight policy is established to offer customers
every advantage possible. Due to bulk freight
ratings on some equipment and other shipping
considerations, freight policies differ by
equipment type. Actual back freight may be
charged for shipments originating from other
than specified FOB warehouses. See Freight
Policy for details.
All STOW domestic sales are FOB nearest
available designated MQ/STOW warehouse.
Export orders are ex-works factory located in
Carson, CA or Boise, ID.
Price changes are effective on a specific date
and all orders received on or after that date will
be billed at the revised price.
RETURNED GOODS POLICY
Return shipments may be accepted and credit
allowed, subject to the following provisions.
Rebates for price reductions and added charges
for price increases will not be made for stock in
dealer inventory at the time of a price change.
1. A Returned Material Authorization (RMA)
must be approved by STOW prior to
shipment. Approvals for returned goods
must be with just cause and are at the
sole discretion of STOW. A copy of the
Authorization must accompany the shipment
to the designated Warehouse.
STOW reserves the right to quote and sell direct
to Government agencies and to Original
Equipment Manufacturer accounts who use our
products as integral parts of their own products.
Additions to orders already shipped cannot be
accepted for freight minimums.
LIMITATION OF SELLER’S LIABILITY
2. Parts being returned must be listed as
currently supplied on the current parts list.
STOW shall not be liable hereunder for damages
in excess of the purchase price of the item with
respect to which damages are claimed and in
no event shall STOW be liable for loss of profit
or good will or for any other special, consequential
or incidental damages.
Should STOW elect to make partial shipments
of an order originally complying with the “freight
allowed” requirements, transportation charges
will be absorbed by STOW on any subsequent
shipment applying to that order.
3. Parts must be in new and resalable condition
in the original package, with part numbers
clearly marked.
4. Units and accessories must be current
models in the latest price list and in new and
resalable condition.
All other orders will be shipped collect or prepaid
with charges added to the invoice. STOW’s
responsibility ceases when a signed manifest
has been obtained from the carrier, and any
claim for shortage or damage must be settled
between the consignee and the carrier.
LIMITATION OF WARRANTIES
There are no warranties, express or implied,
made by STOW. hereunder on Products
manufactured or distributed by it except the
warranty against defects in material and
workmanship on new Products to the original
purchaser, as set forth in the STOW New
Product Limited Warranty.
5. Special order items are not returnable for
credit.
6. Credit on returned parts and units will be
issued at actual dealer net price at time of
purchase less 15% restocking charge.
Parts: FOB Carson, California or Boise,
Idaho. See Freight Policy for details and
additional discounts.
7. All returned shipments are to be made to
the STOW designated receiving point,
freight prepaid at the sender’s expense.
STOW CONSTRUCTION EQUIPMENT
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-661-4242 • 877-BUY-STOW
FAX:310-604-9237
E-MAIL: [email protected]
Atlanta • Boise • Newark • Quebec, Canada
Manchester, UK • Rio de Janeiro, BR • Puebla, MX
PAGE 40 —STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HANDWHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT
800-478-1244
FAX: 310- 537-4259
TECHNICAL ASSISTANCE
800-478-1244
FAX: 310- 631-5032
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
STOWCONSTRUCTIONEQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
PARTS DEPARTMENT:
800-427-1244
FAX: 800-672-7877
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
CARSON, CA 90749
310-537-3700 • 888-252-STOW [888-252-7869]
FAX:310-537-1986 • FAX:800-556-1986
E-MAIL: [email protected] • WWW: stowmfg.com
FAX:310-631-5032
Download from Www.Somanuals.com. All Manuals Search And Download.
|