| Sterling Power Products Automobile Battery Charger PB1206 User Manual | 
| ProBudget Chargers   Sterling Power Products   ENGLISH   Installation   For short term usage connect the batteries   using the enclosed crocodile clips. If the   charger is for a fixed installation it is strongly   recommended that the clip on terminals   be removed and replaced with 8 mm ring   terminals and connected directly to the   battery posts.   Operation:   Fit in a cool dry well ventilated place , as   close to the battery bank as possible.   Turn on the charger. (The power switch is on   the front resp. back of the unit.)   Connect the charger to a 230/110 volt a/c   supply using the enclosed cable.   The front red l.e.d. will confirm there is   power going into the unit.   Connect the d/c side of the charger to the   battery, ensure the red cable is connected   to the positive and the black cable to   negative battery terminal. In the event that   these cables are reversed the charger will   not start, however no harm will come to the   charger as it is protected against this fault   condition.   The l.c.d. (if fitted) or the needle meter will   show the charging of the battery.   This charger can be left on all the time.   ALWAYS ENSURE THAT THE BATTERY   CHARGER IS SUITABLE FOR THE BATTERIES   YOU PROPOSE TO CHARGE.   The bi-colored l.e.d. will show orange for   high charge mode at first, then green for   float charge mode.   THIS UNIT IS SUITABLE FOR OPEN LEAD ACID,   SEALED LEAD ACID, MOST GEL AND   CARBON FIBER BATTERIES.   The battery is fully charged when the unit   l.e.d. turns from orange to green.   DEUTSCH   Installation   benutzen Sie für die Verbindung zur Batterie   die beiliegenden Krokodilklemmen. Wenn   Sie das Ladegerät dauerhaft installieren   möchten, empfehlen wir Ihnen, die   Krokodilklemmen gegen 8mm Ring-   Anschlussklemmen auszutauschen und   diese direkt mit den Batterieklemmen zu   verbinden.   Betrieb:   Betreiben Sie das Ladegerät an einem   kühlen, gut belüfteten Ort, so nah wie   möglich an der Batterie.   Schalten Sie das Ladegerät ein. (Der   Netzschalter ist auf der Vorder- bzw.   Rückseite des Gerätes.)   Verbinden Sie das Ladegerät mit Hilfe des   beiliegenden Anschlusskabels mit 230V   bzw. 110V Wechselspannung.   Die rote LED auf der Vorderseite zeigt an,   dass das Gerät Strom aufnimmt.   Die LCD-Anzeige (falls vorhanden) oder das   Analoginstrument zeigt den Ladevorgang   an.   Dieses Ladegerät kann ständig   eingeschaltet bleiben.   Verbinden Sie den Ladeausgang des   Gerätes mit Ihrer Batterie, so dass das rote   Kabel mit dem positiven Batteriepol und   das schwarze Kabel mit dem negativen   Batteriepol verbunden ist. Bei einem   versehentlichen Vertauschen der Kabel   nimmt das Gerät keinen Schaden, da es   gegen Verpolung geschützt ist.   VERSICHERN SIE SICH VOR DEM   EINSCHALTEN, DASS IHRE BATTERIEN FÜR   DIESES LADEGERÄT GEEIGNET SIND.   Eine weitere LED leuchtet während der   Hauptladung orange und während der   Erhaltungsladung grün.   DIESES LADEGERÄT IST GEEIGNET FÜR   OFFENE BLEI-SÄURE-, VERSIEGELTE BLEI-   SÄURE- UND DIE MEISTEN GEL-BATTERIEN.   Wenn diese LED von orange auf grün   umschaltet, ist die Batterie vollständig   geladen.   Für den kurzfristigen, mobilen Einsatz   Model: Part number   PB1206   100V-240V 100V-240V 180V-240V 100V-240V 180V-240V   PB1210   PB1220   PB2407   PB2412   Input voltage = A/C 47-63 Hz   Out put voltage :   High charge voltage   Float voltage   Efficiency   Protection:   14.4V max 14.4V max 14.4V max 28.8V max 29.8V max   13.6V   87%   13.6V   87%   13.6V   87%   27.2V   87%   27.2V   87%   Reverse polarity protected   Short circuit protected   Overload protected   Over temperature protected   Thermostatically controlled cooling fan   Charge cycle and protection Indication:   L.E.D. R: power on G: float charger Y: high charger   L.C.D   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   yes   no   yes   yes   yes   no   yes   yes   no   yes   yes   no   yes   yes   no   Meter, needle type   Size in mm width height depth   Weight in kg   Accessories , Euro and English cable   70x48x155 103x50x167   115x60x186 103x50x167 115x60x186   0.5   no   0.9   yes   1.2   yes   0.9   yes   1.2   yes   PB1206 ONLY:   TO CONNECT PLUG:   BROWN= LIVE   BLUE = NEUTRAL   GREEN/YELLOW = EARTH   ON/OFF   SWITCH   PB1206   BLACK -   RED +   ORANGE/ HIGH CHARGER   GREEN / FLOAT   - RED LED   UNIT ON   + BATTERY   Copyright 2004 by Sterling Power Products.   Download from Www.Somanuals.com. All Manuals Search And Download.   |