Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters
■
Meets or exceeds current edition of ASHRAE/IES-90.1-1999.
■
Low NOX – TPX Low NOX models meet or exceed current Texas and
California SCAQMD air quality standards.
■
UL – Entire unit UL listed (File No. MH11631).
■
Glass-Lined Tank – Exclusive corrosion protection with glass-
lining on all interior surfaces. Multiple anodes provide even more
corrosion protection.
■
ASME Construction Standard – 160 PSI working pressure on all models.
■
Powered Gas Burner – Powered burner has electronic flame
safeguard control with intermittent spark ignition. Also included are
main and pilot automatic gas valves plus gas pressure regulators,
diaphragm air switch for proof of blower operation.
– TPX Low NOX Models are factory standard with modulating fire.
The burner automatically adjusts the firing rate and the Btu output
to maintain precise system temperature control.
■
Fully Automatic Controls With Safety Shutoff – High temperature
limit control (manual reset). ASME rated temperature and pressure
relief valve. Hinged door control compartment for ease of access. Two
thermostats, upper and lower, for accurate temperature control.
Standard control is for 120˚F - 180˚F water service.
■
Jacket And Insulation – Heavy gauge steel with baked powder coat
finish. Insulated with high-density foam insulation that meets or
exceeds all required standards.
■
Professional Start-Up Service Furnished To Assure Most Efficient
Combustion And Safe Initial Start-Up.
■
Other Features
– Two layers of high temperature ceramic fiber insulation in
combustion chamber
■
Limited Warranty Outline
– If the tank should leak any time during the first three years, under
the terms of the warranty, State Water Heaters will repair or replace
heater; installation, labor, handling and local delivery extra.
– NOTE: This Outline Is NOT A Warranty. For complete information,
consult the written warranty or State Water Heaters.
– Flame inspection port opening
– Mounted on rugged channel iron skids
– Combination temperature and pressure gauge
– Low water cutoff
– ASME rated temperature and pressure relief valve
– Barometric draft regulator
– Two cleanout inspection openings
– 120 volt control circuit
– Drain valve
■
TPO – Oil Fired Models: No. 1 or 2 Oil
– Multi-annular fuel containment combustor head
– Available for firing light fuel oils including diesel
– Oil ignition transformer
– Removable lifting lugs
– Integral 2-stage fuel unit
– Squirrel cage blower
– Oil safety valve
■
Options
– Factory Mutual approved control arrangement
– Industrial Risk Insurance (IRI Gas Train)
– 5 year or 10 year limited warranty
– High or low water pressure switch
– 180°F water service thermostats
– A.G.A. rated T & P Valve
– Modular graphic burner systems management on heaters with
270,000 Btu input and over
– Combustion Air intake Adapter
■
TPD – Dual Fuel Gas/Oil: Natural Gas or Propane & No. 1 or 2 Oil
– Multi-annular fuel containment combustor head
– Gas electric pilot and gas ignition transformer
– Pilot and main pressure regulators
– Air safety switch
– Manual fuel selector switch
– Integral 2-stage fuel unit
– Squirrel cage blower
COMMERCIAL
The Expert’s Choice®
Download from Www.Somanuals.com. All Manuals Search And Download.
TPX Power Low NO Large Volume Commercial Water Heaters
X
SPECIFICATIONS
Input
Rating
BTU/Hr.
Natural
Gas
Nominal
Storage
Capacity
U.S.
Output (Gallons)
Recovery
Dimensions In Inches
Motor HP
120V 60 Hz 1
Model Number
First
Hour
Gallons
Rating 80°F Rise 100°F Rise 140°F Rise
A
B
C
D
E
F
G
H
J
T
PX 150 400 NEA
150
150
200
400,000 507
540,000 644
800,000 936
485
654
970
387
524
776
277
374
554
693
866
1039
554
693
866
1039
554
693
866
1039
1212
1385
693
831⁄2 14
831⁄2 14
831⁄2 15
831⁄2 15
831⁄2 15
831⁄2 15
911⁄2 14
911⁄2 14
911⁄2 14
911⁄2 14
911⁄2 15
911⁄2 15
911⁄2 15
911⁄2 15
911⁄2 15
991⁄2 15
119 15
119 15
119 15
119 15
119 15
1
1
273⁄4 11⁄4
273⁄4 11⁄4
321⁄2 11⁄2
321⁄2 11⁄2
321⁄2 11⁄2
321⁄2 11⁄2
261⁄2 11⁄2
261⁄2 11⁄2
261⁄2 11⁄2
261⁄2 11⁄2
54
54
60
60
60
60
60
60
60
60
67
67
67
67
55
55
67
67
67
55
55
7
8
571⁄2 73
1
⁄
7
HP - 2.5 Amps
TPX 150 540 NEA
TPX 200 800 NEA
TPX 200 1000 NEA
TPX 200 1250 NEA
TPX 200 1500 NEA
TPX 300 800 NEA
TPX 300 1000 NEA
TPX 300 1250 NEA
TPX 300 1500 NEA
TPX 400 800 NEA
TPX 400 1000 NEA
TPX 400 1250 NEA
TPX 400 1500 NEA
TPX 400 1750 NEA
TPX 400 2000 NEA
TPX 600 1000 NEA
TPX 600 1250 NEA
TPX 600 1500 NEA
TPX 600 1750 NEA
TPX 600 2000 NEA
571⁄2 73
11⁄4
11⁄4
11⁄4
11⁄2
11⁄4
11⁄4
11⁄4
11⁄2
11⁄4
11⁄4
11⁄4
11⁄2
2
10
10
12
12
10
10
12
12
10
10
12
12
72
72
72
72
72
72
72
72
84
84
84
84
73
73
73
73
83
83
83
83
81
81
81
81
200 1,000,000 1130
200 1,250,000 1372
200 1,500,000 1615
1212
1515
1818
970
1212
1515
1818
970
1212
1515
1816
2121
2424
1212
1515
1816
2121
2424
970
1212
1455
776
300
800,000 1016
300 1,000,000 1210
300 1,250,000 1452
300 1,500,000 1695
970
1
⁄
3
HP - 8.6 Amps
1212
1455
776
400
800,000 1096
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
2
2
2
2
2
2
2
2
2
2
2
400 1,000,000 1290
400 1,250,000 1532
400 1,500,000 1775
400 1,750,000 2017
400 2,000,000 2259
600 1,000,000 1450
600 1,250,000 1692
600 1,500,000 1935
600 1,750,000 2177
600 2,000,000 2419
970
1212
1455
1697
1939
970
1212
1455
1697
1939
14 911⁄2 81
1 HP - 12.4 Amps
2
14 911⁄2 89
11⁄4
11⁄4
11⁄2
2
10
12
12
84 109
84 109
84 109
1
866
⁄
3
HP - 8.6 Amps
1039
1212
1385
14 911⁄2 109
14 911⁄2 109
1 HP - 12.4 Amps
2
Certified Minimum Installation Clearances to Combustibles:
Front: 18 inches
Back: 0 inches
Sides: 0 inches
Top: 5 inches
ASME
A clearance of 24 inches should be maintained from serviceable parts such as relief valve, power
burner, drain valve and anodes (anodes are located on side above cold water inlet).
Minimum gas supply pressure: 7 Inches W.C.
Maximum gas supply pressure: 13 Inches W.C.
TPX models are Category I appliances (Fan Assisted) and require a negative draft. These units should
only be commonly vented with other Category I negative draft appliances per the latest addition of the
National Fuel Gas Code. An approved/listed Type “B” venting material is recommended. A negative draft
of -0.02˝ to -0.07 is required in the vent.
COMMERCIAL
The Expert’s Choice®
Download from Www.Somanuals.com. All Manuals Search And Download.
TPO Power Oil Large Volume Commercial Water Heaters
SPECIFICATIONS
Actual
Ship.
Output (Gallons)
Recovery
Dimensions In Inches
Storage
Capacity
U.S.
Input
Rating
BTU/Hr.
Firing
Rate
GPH
Wt.
w/Burner
(lbs.)
Motor HP
120V 60 Hz 1
Model Number
Gallons
80°F Rise 100°F Rise 140°F Rise
A
B
C
D
E
F
G
H
J
TPO 150 140 OEA
TPO 150 199 OEA
TPO 150 255 OEA
TPO 150 270 OEA
TPO 150 400 OEA
TPO 150 540 OEA
TPO 150 720 OEA
TPO 200 300 OEA
TPO 200 600 OEA
TPO 200 800 OEA
TPO 200 1000 OEA
TPO 200 1250 OEA
TPO 200 1500 OEA
TPO 300 300 OEA
TPO 300 600 OEA
TPO 300 800 OEA
TPO 300 1000 OEA
TPO 300 1250 OEA
TPO 300 1500 OEA
TPO 400 600 OEA
TPO 400 800 OEA
TPO 400 1000 OEA
TPO 400 1250 OEA
TPO 400 1500 OEA
TPO 400 1750 OEA
TPO 400 2000 OEA
TPO 500 2250 OEA
TPO 500 2500 OEA
TPO 600 720 OEA
TPO 600 1000 OEA
TPO 600 1250 OEA
TPO 600 1500 OEA
TPO 600 1750 OEA
TPO 600 2000 OEA
TPO 600 2250 OEA
TPO 600 2500 OEA
163
163
163
163
151
151
145
221
221
221
140,000
199,000
255,000
270,000
400,000
540,000
720,000
300,000
600,000
800,000
1
170
241
309
327
485
654
873
364
727
136
193
247
262
387
524
698
291
582
776
970
1212
1455
291
582
776
970
1212
1455
582
776
970
1212
1455
1697
1939
2182
2424
698
97
138
176
187
277
374
416
208
416
554
693
866
1039
208
416
554
693
831⁄2 14
831⁄2 14
831⁄2 14
831⁄2 14
831⁄2 14
831⁄2 14
831⁄2 14
831⁄2 15
831⁄2 15
831⁄2 15
831⁄2 15
831⁄2 15
831⁄2 15
911⁄2 14
911⁄2 14
911⁄2 14
911⁄2 14
911⁄2 14
911⁄2 14
911⁄2 15
911⁄2 15
911⁄2 15
911⁄2 15
911⁄2 15
911⁄2 15
991⁄2 15
110 15
110 15
119 15
119 15
119 15
119 15
119 15
119 15
119 15
119 15
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
5
6
6
6
7
8
47 73
47 73
47 73
571⁄2 73
571⁄2 73
571⁄2 73
1292
1292
1292
1397
1397
1505
1510
2098
2098
2103
2103
2467
2757
2150
2150
2308
2308
2584
2774
3207
3212
3212
3212
3402
3528
3669
1.4
1.8
1.9
2.8
3.8
5.1
2.1
4.2
5.7
1
⁄
7
HP - 4.4 Amp
1
1
273⁄4 11⁄4 361⁄2 10 571⁄2 73
⁄
4
3
HP - 4.6 Amp
HP - 5.5 Amp
321⁄2 11⁄2 443⁄4
321⁄2 11⁄2 443⁄4
6
8
661⁄2 73
661⁄2 73
970
321⁄2 11⁄2 443⁄4 10 661⁄2 73
321⁄2 11⁄2 443⁄4 10 661⁄2 73
321⁄2 11⁄2 443⁄4 12 661⁄2 73
321⁄2 11⁄2 443⁄4 12 811⁄2 73
201 1,000,000 7.1
201 1,250,000 8.9
201 1,500,000 10.7
300
300
300
300 1,000,000 7.1
300 1,250,000 8.9
300 1,500,000 10.7
411
411
411 1,000,000 7.1
411 1,250,000 8.9
397 1,500,000 10.7
397 1,750,000 12.5
397 2,000,000 14.2
495 2,250,000
495 2,500,000 17.8
594 720,000 5.1
594 1,000,000 7.1
594 1,250,000 8.9
594 1,500,000 10.7
594 1,750,000 12.5
594 2,000,000 14.3
1212
1515
1818
364
727
970
1212
1515
1818
727
⁄
3
3
3
⁄
4
HP - 10.2 Amp
HP - 4.6 Amp
300,000
600,000
800,000
2.1
4.2
5.7
261⁄2 11⁄2 443⁄4
261⁄2 11⁄2 443⁄4
6
8
661⁄2 83
661⁄2 83
1
⁄
4
261⁄2 11⁄2 443⁄4 10 661⁄2 83
261⁄2 11⁄2 443⁄4 10 661⁄2 83
261⁄2 11⁄2 443⁄4 12 661⁄2 83
261⁄2 11⁄2 443⁄4 12 811⁄2 83
1
⁄
3
HP - 5.5 Amp
866
1039
416
554
693
⁄
4
HP - 10.2 Amp
HP - 4.6 Amp
1
600,000
800,000
4.2
5.7
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
321⁄2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
55
8
761⁄2 81
⁄
4
970
55 10 761⁄2 81
55 10 761⁄2 81
55 12 761⁄2 81
55 12 911⁄2 81
55 14 911⁄2 81
55 14 911⁄2 89
1
1212
1515
1816
2121
2424
2727
3030
873
1212
1515
1816
2121
2424
2727
3030
⁄
3
HP - 5.5 Amp
866
1039
1212
1385
1558
1732
499
693
866
1039
1212
1385
1558
1732
⁄4
HP - 10.2 Amp
16
55 16 911⁄2 100 4277
55 16 911⁄2 100 4419
55 10 761⁄2 109 3667
55 10 761⁄2 109 3667
55 12 761⁄2 109 3667
55 12 911⁄2 109 3837
55 14 911⁄2 109 3837
55 14 911⁄2 109 3837
55 16 911⁄2 109 4477
55 16 911⁄2 109 4619
1 HP - 16 Amp
1
⁄
4
3
HP - 4.6 Amp
HP - 5.5 Amp
970
1
1212
1455
1697
1939
2182
2424
⁄
3
⁄4
HP - 10.2 Amp
575 2,250,000
575 2,500,000 17.8
16
1 HP - 16 Amp
Certified Minimum Installation Clearances to Combustibles:
Front: 18 inches
Back: 0 inches
Sides: 0 inches
Top: 5 inches
A clearance of 24 inches should be maintained from
serviceable parts such as relief valve, power burner, drain
valve and anodes (anodes are located on side above cold
water inlet).
State Titan TPO models are Category I appliances
(Fan Assisted) and require a negative draft. These units
should only be commonly vented with other Category I
negative draft appliances per the latest addition of the
National Fuel Gas Code. An approved/listed Type “B” venting
material is recommended. A negative draft of -0.02˝ to -0.07
is required in the vent.
ASME
COMMERCIAL
The Expert’s Choice®
Download from Www.Somanuals.com. All Manuals Search And Download.
TPD Power Dual Fuel Large Volume Commercial Water Heaters
SPECIFICATIONS
Actual
Ship.
Output (Gallons)
Recovery
Dimensions In Inches
Storage
Capacity
U.S.
Input
Rating
BTU/Hr.
Firing
Rate
GPH
Wt.
w/Burner
(lbs.)
Motor HP
120V 60 Hz 1
Model Number
Gallons
80°F Rise 100°F Rise 140°F Rise
A
B
C
D
E
F
G
H
J
1
TPD 150 140 ONEA
TPD 150 199 ONEA
TPD 150 255 ONEA
TPD 150 270 ONEA
TPD 150 400 ONEA
TPD 150 540 ONEA
TPD 150 720 ONEA
TPD 200 300 ONEA
TPD 200 600 ONEA
TPD 200 800 ONEA
TPD 200 1000 ONEA
TPD 200 1250 ONEA
TPD 200 1500 ONEA
TPD 300 300 ONEA
TPD 300 600 ONEA
TPD 300 800 ONEA
TPD 300 1000 ONEA
TPD 300 1250 ONEA
TPD 300 1500 ONEA
TPD 400 600 ONEA
TPD 400 800 ONEA
TPD 400 1000 ONEA
TPD 400 1250 ONEA
TPD 400 1500 ONEA
TPD 400 1750 ONEA
TPD 400 2000 ONEA
TPD 500 2250 ONEA
TPD 500 2500 ONEA
TPD 600 720 ONEA
TPD 600 1000 ONEA
TPD 600 1250 ONEA
TPD 600 1500 ONEA
TPD 600 1750 ONEA
TPD 600 2000 ONEA
TPD 600 2250 ONEA
TPD 600 2500 ONEA
163
163
163
163
151
151
145
221
221
221
140,000
199,000
255,000
270,000
400,000
540,000
720,000
300,000
600,000
800,000
1
170
241
309
327
485
654
873
364
727
136
193
247
262
387
524
698
291
582
776
970
1212
1455
291
582
776
970
1212
1455
582
776
970
1212
1455
1697
1939
2182
2424
698
97
138
176
187
277
374
416
208
416
554
693
866
1039
208
416
554
693
831⁄2 14
831⁄2 14
831⁄2 14
831⁄2 14
831⁄2 14
831⁄2 14
⁄2
⁄2
⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
273⁄4 11⁄4 361⁄2
5
6
6
6
7
8
47 73
47 73
47 73
571⁄2 73
571⁄2 73
571⁄2 73
1292
1292
1292
1397
1397
1505
1510
2098
2098
2103
2103
2467
2757
2150
2150
2308
2308
2584
2774
3207
3212
3212
3212
3402
3528
3669
1
1
1.4
1.8
1.9
2.8
3.8
5.1
2.1
4.2
5.7
1
⁄7
HP - 4.4 Amp
1
1
1
831⁄2 14 11⁄4 273⁄4 11⁄4 361⁄2 10 571⁄2 73
⁄
4
3
HP - 4.6 Amp
HP - 5.5 Amp
1
1
831⁄2 15
831⁄2 15
1
1
321⁄2 11⁄2 443⁄4
321⁄2 11⁄2 443⁄4
6
8
661⁄2 73
661⁄2 73
970
831⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 10 661⁄2 73
831⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 10 661⁄2 73
831⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 12 661⁄2 73
831⁄2 15 11⁄2 321⁄2 11⁄2 443⁄4 12 811⁄2 73
201 1,000,000 7.1
201 1,250,000 8.9
201 1,500,000 10.7
300
300
300
300 1,000,000 7.1
300 1,250,000 8.9
300 1,500,000 10.7
411
411
411 1,000,000 7.1
411 1,250,000 8.9
397 1,500,000 10.7
397 1,750,000 12.5
397 2,000,000 14.2
495 2,250,000
495 2,500,000 17.8
594 720,000 5.1
594 1,000,000 7.1
594 1,250,000 8.9
594 1,500,000 10.7
594 1,750,000 12.5
594 2,000,000 14.3
1212
1515
1818
364
727
970
1212
1515
1818
727
⁄
3
3
3
⁄
4
HP - 10.2 Amp
HP - 4.6 Amp
300,000
600,000
800,000
2.1
4.2
5.7
911⁄2 14
911⁄2 14
1
1
261⁄2 11⁄2 443⁄4
261⁄2 11⁄2 443⁄4
6
8
661⁄2 83
661⁄2 83
1
⁄4
911⁄2 14 11⁄4 261⁄2 11⁄2 443⁄4 10 661⁄2 83
911⁄2 14 11⁄4 261⁄2 11⁄2 443⁄4 10 661⁄2 83
911⁄2 14 11⁄4 261⁄2 11⁄2 443⁄4 12 661⁄2 83
911⁄2 14 11⁄2 261⁄2 11⁄2 443⁄4 12 811⁄2 83
1
⁄3
HP - 5.5 Amp
866
1039
416
554
693
⁄
4
HP - 10.2 Amp
HP - 4.6 Amp
1
600,000
800,000
4.2
5.7
911⁄2 15
1
321⁄2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
55
8
761⁄2 81
⁄4
970
911⁄2 15 11⁄4 321⁄2
911⁄2 15 11⁄4 321⁄2
911⁄2 15 11⁄4 321⁄2
911⁄2 15 11⁄2 321⁄2
55 10 761⁄2 81
55 10 761⁄2 81
55 12 761⁄2 81
55 12 911⁄2 81
55 14 911⁄2 81
55 14 911⁄2 89
1
1212
1515
1816
2121
2424
2727
3030
873
1212
1515
1816
2121
2424
2727
3030
⁄3
HP - 5.5 Amp
866
1039
1212
1385
1558
1732
499
693
866
1039
1212
1385
1558
1732
911⁄2 15
991⁄2 15
110 15
110 15
2
2
2
2
321⁄2
321⁄2
321⁄2
321⁄2
⁄4
HP - 10.2 Amp
16
55 16 911⁄2 100 4277
55 16 911⁄2 100 4419
55 10 761⁄2 109 3667
55 10 761⁄2 109 3667
55 12 761⁄2 109 3667
55 12 911⁄2 109 3837
55 14 911⁄2 109 3837
55 14 911⁄2 109 3837
55 16 911⁄2 109 4477
55 16 911⁄2 109 4619
1 HP - 16 Amp
119 15 11⁄4 321⁄2
119 15 11⁄4 321⁄2
119 15 11⁄4 321⁄2
119 15 11⁄2 321⁄2
1
⁄
4
3
HP - 4.6 Amp
HP - 5.5 Amp
970
1
1212
1455
1697
1939
2182
2424
⁄
3
119 15
119 15
119 15
119 15
2
2
2
2
321⁄2
321⁄2
321⁄2
321⁄2
⁄4
HP - 10.2 Amp
575 2,250,000
575 2,500,000 17.8
16
1 HP - 16 Amp
Certified Minimum Installation Clearances to Combustibles:
Front: 18 inches
Back: 0 inches
Sides: 0 inches
Top: 5 inches
A clearance of 24 inches should be maintained from
serviceable parts such as relief valve, power burner, drain
valve and anodes (anodes are located on side above cold
water inlet).
State Titan TPD models are Category I appliances
(Fan Assisted) and require a negative draft. These units
should only be commonly vented with other Category I
negative draft appliances per the latest addition of the
National Fuel Gas Code. An approved/listed Type “B” venting
material is recommended. A negative draft of -0.02˝ to -0.07
is required in the vent.
ASME
COMMERCIAL
The Expert’s Choice®
Download from Www.Somanuals.com. All Manuals Search And Download.
Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters
SUGGESTED SPECIFICATIONS
TM
TITAN LV POWER GAS (MODELS TPG)
Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design
and include a powered gas burner with electronic flame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure
regulator, diaphragm air switch for proof of blower operation, and flame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input
rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall
be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, and stamped National
Board, and listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination
temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door shall be hinged for
easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation. Heater(s)
must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efficiency and standby loss. The outer jacket shall have a baked powder coat finish. All internal
surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel by firing at a
temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty. Professional
start-up service to be included.
SUGGESTED SPECIFICATIONS
TM
TITAN LV POWER LOW NOX (MODELS TPX)
Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design
and include a powered gas burner with electronic flame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure
regulator, diaphragm air switch for proof of blower operation, and flame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input
rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall
be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, ASME stamped and listed
by Underwriters Laboratories. The water heater shall be approved for low NOx and meet or exceed California rule 1146.2. The unit shall provide modulating fire for
smooth system operation and precise temperature control. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, modulating
control, combination temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door
shall be hinged for easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam
insulation. Heater(s) must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efficiency and standby loss. The outer jacket shall have a baked powder coat
finish. All internal surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel
by firing at a temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty.
Professional start-up service to be included.
SUGGESTED SPECIFICATIONS
TITAN LV POWER OIL AND DUAL FUEL (MODELS TPO AND TPD)
TM
Water heater(s) shall be Model_____________________as manufactured by the State Water Heaters or an approved equal. Heater(s) shall have a minimum oil firing
rate of_____gallons per hour, an input rating of____________BTU/HR. The heater(s) shall have a recovery rate of_____GPH at a 100°F rise and a storage capacity
of______gallons. The 160 psi design pressure tank shall be glass-lined with an alkaline borosilicate composition and fused to the steel by firing at 1600°F. The heater(s)
shall be equipped with______NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, and carry a National Board stamping. The heater(s) shall be ASME and the
entire unit listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination
temperature and pressure gauge, low water cutoff, ASME rated temperature and pressure relief valve, and barometric draft regulator. Control compartment door shall
be hinged for easy access and include cam locks for security. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be
insulated with high-density foam insulation and meet or exceed current standard of ASHRAE 90.1-1999 for standby loss and recovery efficiency. The heater(s) shall
include a drain valve and flame observation port. The jacket shall be baked powder coat finish. Heater(s) vessel shall have a 3, 5 or 10 year limited warranty against
failure as outlined in the written warranty.
The TPO models shall have a UL listed burner with two-stage pump, oil safety valve, electronic flame safeguard, intermittent ignition and diaphragm air switch for proof
of flame operation.
The TPD models shall include a dual fuel burner with two-stage oil pump, oil safety valve, electronic flame safeguard, intermittent ignition, diaphragm air switch, main
and pilot automatic gas valves, gas pressure regulator and manual crossover switch.
In keeping with our policy of continuous product improvement,
specifications are subject to change without prior notice.
Printed in U.S.A.
STPBGODF/1003
COMMERCIAL
The Expert’s Choice®
©2003 State Water Heaters
Download from Www.Somanuals.com. All Manuals Search And Download.
|