ATC-2000WF User’s Manual
The software described in this manual is furnished under a license agreement and may be used
only in
accordance with the terms of that agreement.
Copyright Notice
Copyright 2007 ATC Technology Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
ATC is a registered trademark of The ATC Technology Co.,Ltd.
All other trademarks or registered marks in this manual belong to their respective
manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a
commitment on the part of ATC
Download from Www.Somanuals.com. All Manuals Search And Download.
●Versatile socket operation modes, including: TCP/IP, UDP/IP, HTTP, ARP, DHCP
client
●Easy-to-use Windows Utility for mass installation
●Supports Windows Virtual COM drivers
●LEDs indicate LINK, DIS, ACT and PWR.
WLAN Radio Features:
Protocol Type: 802.11b standard compliant
Operating Range: Open Environment: 1000 ft./300m
Office Environment: 100-330 ft./30-100m
Security: WEP (Wired Equivalent Privacy) 64 and 128 bit encryption
Network Mode Infrastructure mode, Ad-Hoc mode
1.4 Serial Communication Parameters
No. of ports:1 (ATC-2000WF)
Interface: RS-232/422/485
Port Type:DB9 Male and six bit terminal
Baud Rate Options: 9600, 38400, 57600, 115200 bps
Data Length Options: 8 bits
Parity options: None
Stop Bits Options: 1 bit
Flow Control: Hardware or none
Serial UART Buffer: 256 bytes input, 256 bytes output
Radio Characteristics:
Spread Spectrum Technology: DSSS (Direct Sequence Spread Spectrum)
RF Range: 2.4 ~ 2.4835 GHz
Data Rate: 11 / 5.5 / 2 / 1 Mbps
Modulation: DBPSK for 1 Mbps, DQPSK for 2 Mbps, CCK for 5.5 / 11 Mbps
Operation channels: US - 11, Europe - 13, France - 4, Spain - 2, Japan - 14
RF Power Output (Typ.): +15 dBm
Receive Sensitivity (Typ. @BER 10E-5): -83 dBm@11Mbps
Power:
Power Supply: 9-36VDC
Current: Tx 350mA (Max.), Rx 210mA, Power Saving Mode 80mA
Software:
Windows-based Driver with Multi -Link Virtual Com Driver
PC Set UP Utility: User setup and device-search software run on Windows XP/ 98 /
ME / NT / 2000
Network Protocol: TCP/IP, UDP/IP, SNMP, HTTP, ARP, DHCP client
Mechanical:
Antenna: PCB board-mount antenna option, or
Ipex connector for external antenna and cable option
Dimensions: 95 x 76 x 26 mm)
Environmental:
Temperature: Operating: 0 to +55 °C / +32 to +131 °F
Storage: -20 to +65 °C / -4 to +149 °F
Relative Humidity: 95% (non-condensing)
Emissions EMC Certificate:
U.S.A.: FCC Part 15 Subpart C
CE: ETSI EN 300 328, EN 301 489-1/17, EN 55022, EN 61000, EN 50371
Certification: Some models are already FCC Modular-Certified for immediate
public sale.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Serial Port Pin Assignments
RS-232/422/485 Pinouts
RS-232 Pinout(DB9 Female )
PIN
2
3
5
7
RS-232
RXD
TXD
GND
RTS
Input/Output
I
O
-
O
I
8
CTS
RS-422/485 Pinout(SIX Terminal from Left)
PIN
1
2
RS-422
T+
RS-485
485+
485-
NC
T-
R+
3
4
R-
NC
5
6
VIN+
VIN-
VIN+
VIN+
1.6 Connecting the Hardware
This section describes how to connect ATC-2000WF to serial devices for first time testing
purposes. We cover Wiring Requirements, Connecting the Power, Connecting to the
Network,
You should also pay attention to the following items:
Use separate paths to route wiring for power and devices. If power wiring and device wiring
paths must cross, make sure the wires are perpendicular at the intersection point.
Connecting the Power
Connect the 9-36 VDC power line with ATC-2000 power jack. When the power is
properly supplied, the .Link and DIS. LED will light in red and yellow color until the system
is ready, at which time the .Link. LED will be put out and DIS PWR LED still light.
Connecting to a Serial Device
Connect the serial data cable between ATC-2000WF and the serial device.
1.7 Top Panel LED Indicators
LINK ---- Indicate WLAN status
DIS ---- Indicate WLAN status
ACT ---- It will flash when transmit the data from WLAN to serial
or from serial to WLAN.
PWR ---- Indicate the Power supply
Detail for LINK,DIS Led indicate
LINK
OFF
ON
DIS
OFF
OFF
ON
Status
WLAN Connecting
WLAN Connected
WLAN Disconnect
Setup Command
OFF
ON
ON
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 Initial Configuration
When setting up your ATC-2000WF for the first time, the first thing you should do is
configure the IP address. Select one of the initial IP Address configuration methods to
configure
2.1 Factory Default IP Address
ATC-2000WF is configured with the following default IP addresses:
WLAN:
Setting static IP
IP Address 192.168.1.250
Netmask 255.255.255.0
2.2 Serial Console (19200, n, 8, 1)
Before configuring the ATC-2000WF via the serial console, turn off the power and use a
serial cable to connect the ATC-2000WF to your computer’s serial port.
We suggest using PComm Terminal Emulator, which is available in CD driver to carry out
the configuration procedure. Firstly install PComm Terminal Emulator on your computer.
1. Connect ATC-2000WF RS-232 serial port directly to your computer’s male RS-232
serial
Port with RS-232 DB9 Female Cross Configuration cable
2. From the Windows desktop, click on Start # Programs # PComm Lite # Terminal
Emulator.
3. When the PComm Terminal Emulator window opens, first click on the Port Manager
menu item and select Open, or click on the Open icon.
4. The Property window opens automatically. From the Communication Parameter page,
select the appropriate COM port for the connection, COM1 in this example, and 38400 for
Baud Rate, 8 for Data Bits, None for Parity, and 1 for Stop Bits.
5. From the Property window.s Terminal page, select ANSI or VT100 for Terminal
Type,
Download from Www.Somanuals.com. All Manuals Search And Download.
and click on OK. If you select Dumb Terminal as the terminal type, some of the console
functions—especially the .Monitor. function—may not work properly.
6. Press the “ ←” backspace key (located in the upper right corner of the keyboard)
continuously whilepowering on the ATC-2000WF
.
7. Sending a continuous “ ←” backspace string to ATC-2000WF triggers it to switch
automatically
from data mode to console mode.
8. Start by configuring the IP address and WLAN under MS-DOS Command Mode.
section for instructions on how to configure the rest of the IP settings.
4
Choosing the Proper Operation Mode
In this chapter, we describe the various ATC-2000WF operation modes. The options
include
an operation mode that uses a driver installed on the host computer, and operation modes
that rely
on TCP/IP socket programming concepts. After choosing the proper operation mode in this
chapter, refer to Chapter 5 for detailed configuration parameter definitions.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0 Summary of Commands – Listed by Functional Category
(These commands are explained in detail with more detailed functioning examples further
in this document.)
Network Commands
IP xxx.xxx.xxx.xxx Where x is the IP of this device
MASK xxx.xxx.xxx.xxx Where x is the Network Mask of this device
GW xxx.xxx.xxx.xxx Where x is the Gateway of this device
DHCP x Where x is the DHCP setting: 1=ON 0=OFF
Wireless LAN Commands
CHAN x Where x is the channel setting 1-14
MODE x Where x Network Mode x = a(ad hoc) b(infrastructure) p(Pseudo IBSS)
SSID xxxxxxxxx Where x is the multi-character SSID network name
RATE x Where x is the Tx rate, 1,2,5,11 mbps
WEP x Where x is WEP key 0=OFF, 1=64bit, 2=128bit
WK x yyyyyyyyyy Load WEP Encryption Key into WEP buffers 1, 2, 3 or 4
WKID x Where x is the Buffer of the WEP encryption key in use 1, 2, 3 or 4
AA x Where x is the authentication: A=Auto, S=Shared Key, O=Open
Serial Port Commands
BAUD x Where x is serial port baud rate, 0=115200, 1=57600, 2=38400, 3=9600
FCTL x Where x is Serial Flow Control setting, 1=ON, 0=OFF
PORT xxxxx Where x= TCP Serial Port Number (Default value is “1001”)
Server/Client Settings
RMODE x Where x is CLIENT or SERVER setting for this device
RIP xxx.xxx.xxx.xxx Where x is Server Target Remote IP when this device is in Client
mode.
RPORT xxxxx Where x is Server Target Remote PORT when this device Client mode.
Enter Command Mode
SetUpWLAN Gatekeeper Command Entry String
Exit and Save Settings Commands
EXIT Exits Command Mode but DOES NOT SAVE CHANGES
SAVE SAVE Command (Saves only but does not Exit Configuration Mode.)
SE SAVES and EXITS Command Mode simultaneously
Other Commands
PSMOD x Where x is the power saving mode: 1=ON 0=OFF
RES Reset as if a Hardware reset was applied
DEF Restores all settings to Factory Default
MAC Read-Only command that display the unique MAC address
VER Read-Only command returns Firmware Version Number
HELP Displays list of all available Commands along with abbreviated format
LIST Displays alphabetic readout of all Mini-b Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
|