RV06
HYDRAULIC
ROCKER VALVE
USER MANUAL
Safety, Operation and Maintenance
© 2014 Stanley Black & Decker, Inc.
New Britain, CT 06053
U.S.A.
24056 9/2014 Ver. 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SAFETY SYMBOLS ..................................................................................................................................................4
SAFETY PRECAUTIONS..........................................................................................................................................5
TOOL STICKERS & TAGS........................................................................................................................................6
HOSE TYPES............................................................................................................................................................7
HOSE RECOMMENDATIONS ..................................................................................................................................8
FIGURE 1. TYPICAL HOSE CONNECTIONS.......................................................................................................8
HTMA REQUIREMENTS...........................................................................................................................................9
OPERATION............................................................................................................................................................10
FIGURE 2. CONNECTING THE RV06 TO A DOUBLE-ACTING TOOL ..............................................................10
FIGURE 3. CONNECTING THE RV06 TO A SINGLE-ACTING TOOL................................................................10
TOOL PROTECTION & CARE................................................................................................................................12
TROUBLESHOOTING ............................................................................................................................................13
SPECIFICATIONS...................................................................................................................................................14
HYDRAULIC SYSTEM REQUIREMENTS..............................................................................................................14
RV06 PARTS ILLUSTRATION ................................................................................................................................15
RV06 PARTS LIST ..................................................................................................................................................16
IMPORTANT
To fill out a Product Warranty Validation form, and for information on your warranty,
visit Stanleyhydraulics.com and select the Company tab, Warranty.
(NOTE: The warranty Validation record must be submitted to validate the warranty).
SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic
Tools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au-
thorized and certified dealer. Please read the following warning.
WARNING
SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR
SERVICE OF THIS TOOL.
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN
AUTHORIZED AND CERTIFIED DEALER.
For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this
manual and ask for a Customer Service Representative.
RV06 User Manual ◄ 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SYMBOLS
Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair ac-
tions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equipment.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible
injury or death.
This safety alert and signal word indicate an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
DANGER
WARNING
CAUTION
This safety alert and signal word indicate a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
This safety alert and signal word indicate a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
This signal word indicates a potentially hazardous situation which, if not avoid-
ed, may result in property damage.
CAUTION
NOTICE
This signal word indicates a situation which, if not avoided, will result in damage
to the equipment.
This signal word indicates a situation which, if not avoided, may result in dam-
age to the equipment.
IMPORTANT
Always observe safety symbols. They are included for your safety and for the protection of the tool.
LOCAL SAFETY REGULATIONS
Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte-
nance personnel.
4 ► RV06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
Tool operators and maintenance personnel must always
•
Damaged fittings, connectors, quick couplers, and
comply with the safety precautions given in this manual,
and on the stickers and tags attached to or on the tool
and hose(s).
hoses may fail at or below their rated working pres-
sure, resulting in serious injury or death.
•
Do not attempt to locate hydraulic leaks by feel-
ing around hoses and fittings with bare hands OR
gloved hands. Pin-hole leaks can penetrate the skin
(oil injection). To inspect for leaks, de-pressurize
the system (rocker valve, intensified, and power
source), clean around the suspected area, pres-
surize the system and visually inspect for leaks. If
possible, the above procedure should be performed
behind some type of shield (Lexan®).
These safety precautions are for your safety. Review
them carefully before operating the tool or performing
any maintenance or repairs.
Supervising personnel may specify additional precau-
tions for your work area to comply with company policies
and local safety regulations. Enter any added precau-
tions in the space provided in this manual.
The RV06 Rocker Valve will provide safe, dependable
service if operated in accordance with the instructions
given in this manual. Read and understand the manu-
al any decals, labels, or tags attached to the tool and
hose(s). Failure to do so can cause serious personal in-
jury or damage to the equipment.
•
•
Do not operate the tool at fluid temperatures above
140 °F/60 °C. Operation at higher temperatures can
cause higher than normal temperatures at the tool,
which can result in operator discomfort.
To avoid personal injury or equipment damage, all
tool maintenance, repair, and service must be per-
formed by properly trained personnel.
•
Operator must start in a work area without bystand-
ers. The operator must be familiar with all prohibited
work areas such as excessive slopes and danger-
ous terrain conditions.
•
•
•
Establish a training program for all operators to en-
sure safe operation of the tool.
Do not operate the tool unless thoroughly trained or
under the supervision of the instructor.
Always wear personal protection equipment (PPE)
such as goggles, safety shoes, head, eye, breath-
ing, and ear protection when operating the tool. Use
gloves and aprons when necessary.
•
•
All fittings, connectors, quick couplers, and hoses
used in the high pressure circuit must be capable of
10,000 psi/690 bar operation.
All fittings, connectors, quick couplers, and hoses
must be leak-tight and free of cracks, dents and
other damage.
•
•
Do not operate the tool if it is damaged, improperly
adjusted, or incompletely assembled.
Use only hydraulic hoses labeled and certified non-
conductive when using the rocker valve/intensifier
on or near electric lines.
•
•
Do not use tightly coiled or twisted hoses.
Hoses should not be kinked, cut, swollen or heavily
abraded at any point along their entire length.
RV06 User Manual ◄ 5
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOL STICKERS & TAGS
DANGER
Failure to use hydraulic hose labeled and certified
as non-conductive when using hydraulic tools on
or near electric lines may result in death or
serious injury.
For proper and safe operation read owners manual
and mwke sure that you have been properly
trained in correct procedures required for work
on or around electric lines.
ELECTROCUTION
HAZARD
05153
Stanley Sticker
12412
Electrical Warning Sticker
NOTE:
D A N G E R
D A N G E R
THE INFORMATION LISTED
ON THE STICKERS SHOWN,
MUST BE LEGIBLE AT ALL
TIMES.
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CER-
TIFIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC
TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN
DEATH OR SERIOUS INJURY.
D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO
NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR
DAMAGED HOSE.
3. MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-
NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.
SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-
NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE
MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT.
REVERSING CONNECTIONS MAY CAUSE REVERSE
TOOL OPERATION WHICH CAN RESULT IN SEVERE
PERSONAL INJURY.
BEFORE USING HOSE LABELEDAND CERTIFIEDAS NON-
CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE
HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE
SHOULD BE REGULARLY TESTED FOR ELECTRIC CUR-
RENT LEAKAGE IN ACCORDANCE WITH YOUR SAFETY
DEPARTMENT INSTRUCTIONS.
REPLACE DECALS IF
THEY BECOME WORN OR
DAMAGED. REPLACEMENTS
ARE AVAILABLE FROM
YOUR LOCAL STANLEY
DISTRIBUTOR.
2. A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJEC-
TION INTO THE BODY OR CAUSE OTHER SEVERE
PERSONAL INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-
CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN
LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY
THE SAME SYSTEMAND/OR SEVERE PERSONAL INJURY.
A. DO NOT EXCEED SPECIFIED FLOW AND PRESSURE
FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY
CAUSE A LEAK OR BURST.
5. BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.
KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
B. DO NOT EXCEED RATED WORKING PRESSURE OF
HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS
PRESSURE MAY CAUSE A LEAK OR BURST.
6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-
TECTION.
7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE,
ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST
ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY
TRAINED PERSONNEL.
C. CHECK TOOL HOSE COUPLERS AND CONNECTORS
DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH
YOUR HANDS. CONTACT WITH A LEAK MAY RESULT
IN SEVERE PERSONAL INJURY.
The safety tag (P/N 15875) at right is
attached to the tool when shipped from
the factory. Read and understand the
safety instructions listed on this tag before
removal. We suggest you retain this tag and
attach it to the tool when not in use.
I M P O R T A N T
I M P O R T A N T
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
SEE OTHER SIDE
SAFETY TAG P/N 15875 (Shown smaller then actual size)
6 ► RV06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSE TYPES
The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy-
draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with
Stanley Hydraulic Tools. They are:
Certified non-conductive — constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid
reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non-
conductive is the only hose authorized for use near electrical conductors.
Wire-braided (conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce-
ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near
electrical conductors.
Fabric-braided (not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in-
ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This
hose is not certified non-conductive and must never be used near electrical conductors.
HOSE SAFETY TAGS
To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic
Tools. DO NOT REMOVE THESE TAGS.
If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be
obtained from your Stanley Distributor.
THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE
D A N G E R
D A N G E R
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE
WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN
DEATH OR SERIOUS INJURY.
3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE
OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.
KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT
CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION
AND SEVERE PERSONAL INJURY.
FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-
ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND
ELECTRIC LINES.
4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR
CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT
USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.
2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE
ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-
TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND
TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH
SAFETY DEPARTMENT INSTRUCTIONS.
5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-
AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE
IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
SEE OTHER SIDE
SEE OTHER SIDE
SIDE 1
SIDE 2
(Shown smaller than actual size)
THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.
D A N G E R
D A N G E R
1. DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS
NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR
ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.
5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKSABRASIONS, BULGES, OR DAMAGE TO
COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.
NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
2. FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY
TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-
TRIC LINES.
6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR
HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE
AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT
DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE
PERSONAL INJURY.
4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT
WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO
PULL OR LIFT TOOLS, POWER UNITS, ETC.
SEE OTHER SIDE
SEE OTHER SIDE
SIDE 1
SIDE 2
(Shown smaller than actual size)
RV06 User Manual ◄ 7
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSE RECOMMENDATIONS
8 ► RV06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
HTMA / EHTMA REQUIREMENTS
HTMA
TOOL TYPE
HYDRAULIC SYSTEM REQUIREMENTS
TYPE I
TYPE II
TYPE RR
9-10.5 gpm
(34-40 lpm)
1500 psi
TYPE III
11-13 gpm
(42-49 lpm)
1500 psi
4-6 gpm
7-9 gpm
Flow Range
(15-23 lpm)
1500 psi
(103 bar)
(26-34 lpm)
1500 psi
(103 bar)
Nominal Operating Pressure
(at the power supply outlet)
(103 bar)
(103 bar)
2100-2250 psi
(145-155 bar)
2100-2250 psi
(145-155 bar)
2200-2300 psi
(152-159 bar)
2100-2250 psi
(145-155 bar)
System relief valve setting
(at the power supply outlet)
250 psi
(17 bar)
250 psi
(17 bar)
250 psi
(17 bar)
250 psi
(17 bar)
Maximum back pressure
(at tool end of the return hose)
400 ssu*
400 ssu*
400 ssu*
400 ssu*
Measured at a max. fluid viscosity of:
(82 centistokes) (82 centistokes) (82 centistokes) (82 centistokes)
(at min. operating temperature)
Temperature: Sufficient heat rejection
capacity to limit max. fluid temperature to:
(at max. expected ambient temperature)
140° F
(60° C)
140° F
(60° C)
140° F
(60° C)
140° F
(60° C)
Min. cooling capacity at a temperature
3 hp
5 hp
6 hp
7 hp
difference of between ambient and fluid
temps
(2.24 kW)
40° F
(3.73 kW)
40° F
(5.22 kW)
40° F
(4.47 kW)
40° F
NOTE:
(22° C)
(22° C)
(22° C)
(22° C)
Do not operate the tool at oil temperatures above 140° F (60° C). Operation at higher temperatures can cause operator
discomfort at the tool.
Filter
25 microns
30 gpm
(114 lpm)
25 microns
30 gpm
(114 lpm)
25 microns
30 gpm
(114 lpm)
25 microns
30 gpm
(114 lpm)
Min. full-flow filtration
Sized for flow of at least:
(For cold temp. startup and max.
dirt-holding capacity)
Hydraulic fluid Petroleum based
(premium grade, anti-wear, non-conductive)
Viscosity (at min. and max. operating temps)
100-400 ssu*
100-400 ssu*
(20-82 centistokes)
100-400 ssu*
100-400 ssu*
NOTE:
When choosing hydraulic fluid, the expected oil temperature extremes that will be experienced in service determine the
most suitable temperature viscosity characteristics. Hydraulic fluids with a viscosity index over 140 will meet the requirements
over a wide range of operating temperatures.
*SSU = Saybolt Seconds Universal
CLASSIFICATION
EHTMA
HYDRAULIC SYSTEM
REQUIREMENTS
C
B
D
Flow Range
3.5-4.3 gpm
(13.5-16.5 lpm) (18-22 lpm)
1870 psi
(129 bar)
4.7-5.8 gpm
7.1-8.7 gpm
(27-33 lpm)
1500 psi
9.5-11.6 gpm
(36-44 lpm)
1500 psi
11.8-14.5 gpm
(45-55 lpm)
1500 psi
Nominal Operating Pressure
(at the power supply outlet)
1500 psi
(103 bar)
(103 bar)
(103 bar)
(103 bar)
System relief valve setting
(at the power supply outlet)
2495 psi
(172 bar)
2000 psi
(138 bar)
2000 psi
(138 bar)
2000 psi
(138 bar)
2000 psi
(138 bar)
NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements
RV06 User Manual ◄ 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The RV06 is ported at both ends with a 1/4 in. female
PREOPERATION PROCEDURES
CONNECT HOSES
NPT ports. When using Teflon® tape as a sealant be
careful not to allow the tape to enter the intensifier,
RV06, or tools connected to the RV06. Contamina-
tion may disable the intensifier, RV06, or the tool.
1. If the RV06 is to be used on or near electrical lines,
both of the hoses used to connect the RV06 to the
intensifier must be labeled and certified non-con-
ductive (see Hose Recommendations). Both pres-
sure and return hoses must be rated for a minimum
working pressure of 10,000 psi/690 bar.
CONNECTING A DOUBLE-ACTING TOOL
A double-acting tool is any tool using hydraulic power
for both the advance and retract modes. Connect the
advance port of the tool to the advance port (marked A)
of the RV06. Connect the retract port of the tool to the
retract port (marked B) of the RV06.
2. Make certain that all fittings, connectors, and quick
couplers used to make connections with the RV06
and the intensifier are rated for 10,000 psi/690 bar.
3. It is a good practice to connect return hoses first and
disconnect them last to minimize or avoid trapped
pressure within the tool or hoses.
4. Wipe all hoses and couplers with a clean, lint-free
cloth before making connections.
5. Connect the hoses on the RV06 to the high-pres-
sure outlet and return port of the intensifier.
6. Observe the marking on the end of the RV06 and
the intensifier: P is the pressure inlet port of the
RV06 and should be connected to the P (pressure
outlet) port of the intensifier. The T (tank or return)
port of the RV06 should be connected to the T port
of the intensifier.
Figure 2. Connecting the RV06 to a Double-Acting Tool
A single-acting tool is any tool using hydraulic power for
the advance mode and a spring for the retract modes.
Single-acting tools use a single connection to the RV06.
Single-acting tools connect to the RV06 in a way similar
to double-acting tools. Only the advance port (marked A)
of the RV06 is used to connect to the tool. The return
port (marked B) is plugged with a 1/4 in. male NPT plug.
7. Tighten all connections securely.
CONNECTING A TOOL TO THE RV06
The RV06 can be used to control the actuation of both
single and double-acting compression and crimping
tools, cutters, high-pressure lifting devices and rebar
benders. Tool connection to the RV06 can be accom-
plished in three ways:
1. A combination of high-pressure (10,000 psi/690 bar)
hose and couplers.
2. High-pressure (10,000 psi/690 bar) couplings only.
NOTE:
Figure 3. Connecting the RV06 to a Single-Acting Tool
In order to use couplings only, it is necessary that
the spacing of the pressure and return ports of a
double-acting tool align exactly with the pressure
and return ports of the RV06.
3. High-pressure (10,000 psi/690 bar) hose only.
10 ► RV06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATING PROCEDURES
COLD WEATHER OPERATION
•
Observe all safety precautions given in this manual. If the RV06 is to be used during cold weather, preheat
the hydraulic fluid at low engine speed. When using the
normally recommended fluids, fluid temperature should
be at or above 50 °F/10 °C (400 ssu/82 centistokes) be-
•
Refer to the applicable manual for the tool connect-
ed to the RV06.
•
Activate the parent circuit to provide power to the in-
fore use.
tensifier. Pressure will now be available at the pres-
Damage to the hydraulic system or RV06 can result
sure port of the RV06.
from use with fluid that is too viscous or thick.
•
•
To advance the ram of the connected tool, press the
forward end of the rocker arm.
When the crimp or cut is complete, release the rock-
er arm and the RV06 will go to a “neutral” or “hold”
position. The tool ram will remain stationary.
•
To retract the tool ram, press the rear of the rocker
arm. If the RV06 is connected to a double-acting
tool, the ram will retract under power. If the tool is
single-acting, the ram will retract somewhat more
slowly due to its spring return.
RV06 User Manual ◄ 11
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOL PROTECTION & CARE
NOTICE
In addition to the Safety Precautions found in
this manual, observe the following for equipment
protection and care.
•
•
•
Make sure all critical tool markings, such as labels
and warning decals, are securely in place and leg-
ible. Replace any that are damaged or missing.
•
•
The intensifier used to power the rocker valve can
usually be adjusted for lower operating pressures.
This work should only be performed by a qualified
hydraulic technician.
The rated working pressure of the hoses must be
equal to (or greater than) the relief-valve setting on
the hydraulic system.
Always replace hoses, couplings, and other parts
with replacement parts recommended by Stanley
Hydraulic Tools. The hydraulic hoses to the rocker
valve must have a minimum working pressure of
10,000 psi/690 bar.
Always store an idle tool in a clean dry space, safe
from damage or pilferage.
•
•
Operate the tool within its rated capacity.
•
•
All hoses must have oil resistant inner surface and
an abrasion resistant outer covering. Whenever
near electrical conductors, only hoses labeled and
certified as non-conductive should be used.
Do not use the tool for applications for which it was
not designed.
•
•
Never connect or disconnect couplers or port con-
nections with hydraulic pressure in the hose.
The hydraulic circuit control valve must be in the
OFF position when coupling or uncoupling the tool.
Wipe all couplers clean before connecting. Use only
lint-free cloths. Failure to do so may result in dam-
age to the quick couplers and cause overheating of
the hydraulic system.
Make sure the compression tool, cutter or lifting de-
vice attached to the rocker valve is capable of op-
eration at 10,000 psi/690 bar.
•
If the operating pressure of the compression tool,
cutter or lifting device attached to the rocker valve is
below 10,000 psi/690 bar, DO NOT USE IT.
12 ► RV06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem.
When diagnosing faults in operation of the control valve, always check that the high-pressure hydraulic power
source is supplying the correct hydraulic flow and pressure to the control valve. Use a pressure gauge known to be
accurate. Check the flow with the hydraulic fluid temperature at least 80 °F/27 °C.
Problem
Cause
Solution
Not automatically returning to Return or tank hose from control valve If hose is kinked, replace it.
the NEUTRAL position.
to the intensifier may be restricted
If the hose has some obstruction in it,
clear the hose or replace it.
If hose coupler is obstructed, clean the
coupler or replace it.
Hose size may be too small for
application. Replace with larger hose.
If tool is equipped with an equalizing
valve, valve setting is lower than
control valve unloading valve setting.
Test and reset tool equalizing valve.
Dirt of debris causing push rod(s) to
bind.
Clean thoroughly.
Tool will not advance.
High-pressure hydraulic system is not Inspect high-pressure hydraulic system
providing flow. for proper operation.
Control valve reverse plumbed to high- Check for proper connection.
pressure hydraulic system.
Transfer disc installed 180° out of
correct position.
Inspect transfer disc installation and
correct it, if necessary.
RV06 User Manual ◄ 13
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Weight ................................................................................................................................................... 2.6 lb/1.18 kg
Length................................................................................................................................................5 1/8 in/130 mm
Width .........................................................................................................................................................2 in/51 mm
Pressure........................................................................................................................................10,000 psi/690 bar
Porting..........................................................................................................................................1/4 in. Female NPT
HYDRAULIC SYSTEM REQUIREMENTS
The RV06 Rocker Valve hydraulic system requirements are determined by the hydraulic pressure rating of the tool
being controlled by the RV06. The following general rules apply when choosing a tool to match up with the RV06.
•
•
•
Whenever possible, Stanley Hydraulic Tools recommends that you use the Stanley IP16 Intensapress intensi-
fier to power the RV06 and tools attached to it.
Make sure the compression tool, cutter, or lifting device attached to the rocker valve is capable of operation at
10,000 psi/690 bar.
If the operating pressure of the compression tool, cutter, or lifting device attached to the rocker valve is below
10,000 psi/690 bar, DO NOT USE IT with an intensifier or hydraulic supply adjusted to deliver 10,000 psi/690
bar.
•
•
•
The intensifier used to power the rocker valve can usually be adjusted for lower operating pressures. This work
should only be performed by a qualified hydraulic technician.
If the intensifier pressure cannot be lowered to match the tool you are using, you must either use a tool rated at
the available operating pressure or utilize an intensifier with the correct output pressure.
If you are in doubt about the tool or intensifier you intend to use with the RV06, please contact Stanley Hydraulic
Tools for assistance.
14 ► RV06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
RV06 PARTS ILLUSTRATION
RV06 User Manual ◄ 15
Download from Www.Somanuals.com. All Manuals Search And Download.
RV06 PARTS LIST
PART
NO.
ITEM
1
QTY
1
1
2
1
1
1
1
1
1
1
1
1
1
3
3
3
3
1
2
2
2
2
1
1
1
1
1
DESCRIPTION
05338
12838
23128
05337
15399
00018
12227
08019
08020
18092
12254
12253
15398
12224
12280
12252
12255
20239
12251
21027
12221
19592
20294
12412
05183
12891
12241
BODY
2
PIPE COUPLING 1/4 NPT
HOSE ASSY
3
4
NIPPLE
5
BACK-UP RING
6
O-RING 7/16 × 9/16 × 1/16 •
MANIFOLD CAP
7
8
BEARING RACE
9
NEEDLE BEARING
TRANSFER DISC
O-RING 1-3/4 × 1-7/8 × 1/16 •
O-RING 3/8 × 1/2 × 1/16 •
BACK-UP RING
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
MANIFOLD GROMMET
BACK-UP RING
O-RING 1/8 × 1/4 × 1/16 •
SPRING
MANIFOLD
SPRING
PUSH ROD
ADJUSTING NUT
PHILLIPS HD SCREW 1/4-20 × 1/4
ROCKER ARM
ELECTRICAL DANGER STICKER
STANLEY STICKER
DANGER STICKER
UNLOADING VALVE ASSY
• Denotes part in Seal Kit P/N 14787
16 ► RV06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie, Oregon 97267-5698 USA
(503) 659-5660 / Fax (503) 652-1780
Download from Www.Somanuals.com. All Manuals Search And Download.
|