HTINT650S, HTINT650W
<Wall mount>
◐NOTES
◐SPECIFICATION
1. You can install the camera indoors or outdoors.
2. Be careful not to scratch the lens or dome cover.
3. Use 1Amp power supply at 12V DC or 24V AC.
Model No.
Image Sensor
Effective Pixel
Cell Size
HTINT650S, HTINT650W
1/3" SONY SUPER HAD CCD
Ⅱ
768(H) X 494(V) PIXEL
6.35㎛(H) X 7.4㎛(V)
Scanning System
Sync. Type
OSD
2 : 1 Interlace
◐FEATURES
1. IP67 (Waterproof)
Internal / Line lock(24V AC)
Multi-language
2. Construction
WDR Set
SSDR / BLC / HLC / OFF
Body : Aluminum, Dome : Polycarbonate
3. (Optional) Wall, Ceiling and pole mounts available
4. 25M range visible in total darkness with 24pcs of
IR LEDs (depends upon scene reflection)
5. Side control board for easy function adjustment
6. Dual power (12V DC or 24V AC) operation
Resolution
S/N Ratio
Color : 600 TV-Line, B/W : 700 TV-Line
52dB(AGC OFF, Weight ON)
LED ON : 0 Lux(25M Range)
LED OFF : 0.0005 Lux(Color Sense-up),
0.0002 Lux(B/W Sense-up)
ATW(1,700°K ~ 11,000°K) /
AWC / MANUAL / OUTDOOR / INDOOR
Min. Illumination
Color Temp.
Shutter
1/60 ~ 1/120,000sec
Intensifier
Gain Control
Speco DNR
V Motion
Privacy
AUTO / FIXED / OFF(x2 ~ x512 selectable)
LOW / HIGH / OFF
◐DIMENSION
2. Pipe application
(1) Remove the screw for fixing a cable on the bottom
of the base.
OFF / ON(1 ~ 32 Level adjustable)
ON / OFF(8 Zone, Alarm output)
ON / OFF(12 Zone)
(2) Open the DOME COVER.
Mirror
H / V / BOTH / OFF
(3) Remove the TAP COVER and place the cables there.
Clarity
ON / OFF(Level adjustable)
ICR(COLOR / Black&White / AUTO)
ON / OFF
(4) After distributing cables, use the TEPLON tape to
wipe the pipe.
D&N
Stabilize
Digital Zoom
DPC
(5) Attach the pipe to the base.
ON(x16) / OFF
<Caution> If you don't wipe TEFLON tape on pipe, it
might cause water intrusion issues.
256 point(Even 128 point, ODD 128 point)
Regulated 12V DC or 24V AC
Power Supply
Current Consumption 150mA(LED OFF), 500mA(LED ON)
◐HOW TO INSTALL
1. Camera installation
(1) Fix the camera with the supplied screws on
ceiling or wall mount.
(2) Please refer to '3. Camera angle adjustment' regarding
adjust camera angle.
Operation Temp.
Dimension
Weight
-20 to 122
Ø150 x 98.6(H)mm
1.76Ibs
※The specification is subject to change without any
prior notice to improve the quality.
(3) Lens adjustment
◐FUNCTIONS
1. Setup for camera functions
After opening the LED cover,
①ENTER :
①By turning the "Tele-Wide" knob, you can access a
- Push the lever : Used to access the menu and
confirm selection.
- Push the lever for one second : Open the menu or
close the menu.
range of focal lengths within specified limits.
②By turning the "Near-Far" knob, you can set the
focus toward an object.
(4) Reassemble the camera.
②Up, ③Down :
Used to move the cursor to up or down.
<Ceiling mount>
④Left, ⑤Right :
Used to move the cursor to left or right and change
the value.
3. Camera angle adjustment
(1) Pan adjustment : Grasp the disk of camera and
adjust direction to the right or left(-160˚~ 190˚)
⑥EXT-VIDEO :
(2) Tilt adjustment : Grasp the LED cover of camera and
adjust direction to up or down(6˚~ 90˚)
Extra video output terminal for installation.
Plug your test monitor in here. The cable is option.
(3) Roll adjustment : Grasp the camera holder and
then rotate(-178˚~ 178˚)
<Caution> If you try to adjust the camera out of limited
angle, it might cause damage to camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
|