3-867-185-11 (1)
Pe rso n a l Au d io
Syst e m
Operating Instructions
ZS-D5
1999 by Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f co n t e n t s
Ba sic Op e ra t io n s
4
6
8
Playing a CD
Listening to the radio
Playing a tape
10 Recording on a tape
CD Pla ye r
Th e Tim e r
12 Using the display
28 Setting the clock
13 Locating a specific track
29 Waking up to music
14 Playing tracks repeatedly
31 Falling asleep to music
32 Timer-recording radio programs
(Repeat Play)
15 Playing a single track
(Single Track Play)
Se t t in g Up
16 Playing tracks in random order
34 Choosing the power sources
(Shuffle Play)
36 Connecting optional components
17 Creating your own program
(Program Play)
39 Selecting the audio emphasis
(Sound Mode/ MEGA BASS)
Th e Ra d io
Ad d it io n a l In fo rm a t io n
19 Presetting radio stations
40 Precautions
42 Troubleshooting
45 Maintenance
46 Specifications
47 Index
20 Playing preset radio stations
Th e Ta p e Pla ye r
21 Finding the beginning of
a track
22 Recording the tracks on CD by
specifying the tape length
Introduction
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Pla yin g a CD
3
1,2
Connect the supplied AC power cord (see page 34).
1
Press 6PUSH OPEN/ CLOSE
and place the CD on the CD
compartment.
With the label side up
2
Close the CD compartment.
Display
3
Press ^.
(On the remote, press (on the
CD section.)
The player turns on (direct
power-on) and the player plays
Track number Playing time
all the tracks once.
4
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
POWER ^ p 6PUSH OPEN/CLOSE
VOLUME +, –
=, +
Tip
Next time you want to
listen to a CD, just
press ^. The player
turns on automatically
and starts playing the
CD.
To
Press
Adjust the volume
Stop playback
VOLUME +, –
p
Pause playback
^
(On the remote, press P.)
Press again to resume play
after pause.
Go to the next track
+
Go back to the previous track =
Remove the CD
6PUSH OPEN/ CLOSE
POWER
Turn on/ off the player
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
5
List e n in g t o t h e ra d io
1
2
Connect the supplied AC power cord (see page 34).
Display
1
2
Press BAND until the band you
want appears in the display
(direct power-on).
Indicates an FM
stereo broadcast.
Hold down TUNE/ TIME SET +
or – until the frequency digits
begin to change in the display.
The player automatically scans
the radio frequencies and stops
when it finds a clear station.
If you can't tune in a station,
press TUNE/ TIME SET + or –
until you tune in the station you
want.
6
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
POWER
MODE•MONO/ST ISS
VOLUME +, –
To
Press
Adjust the volume
VOLUME +, –
POWER
Turn on/ off the radio
Tips
To improve broadcast reception
•
If the FM broadcast is
noisy, press
Reorient the antenna for FM. Reorient the player itself
for AM.
MODE• MONO/ ST ISS
until “Mono” appears
in the display and the
radio will play in
monaural.
•
Next time you want to
listen to the radio, just
press the BAND
button. The player
turns on automatically
and starts playing the
previous station.
For FM
For AM
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Pla yin g a t a p e
3 1,2
Connect the supplied AC power cord (see page 34).
1
2
Press 6PUSH OPEN/ CLOSE to
open the tape compartment and
insert a recorded tape. Use TYPE I
(normal), TYPE II (high position)
and TYPE IV (metal) tapes.
With the side you w ant
to play facing forw ard
Press 6PUSH OPEN/ CLOSE to
close the compartment.
Display
3
Press (.
(On the remote, press TAPE (.)
The player turns on (direct
power-on) and starts playing.
Tape counter
8
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
POWER p 9
VOLUME +, –
0, )
DIR MODE
COUNTER RESET
Tips
To
Press
•
Press COUNTER
Adjust the volume
VOLUME +, –
RESET to reset the
counter to “000.”
Stop playback
p
•
Next time you want to
listen to a tape, just
press (or 9. The
player turns on
Play the reverse side
9
Fast-forward or rewind the tape )or 0
automatically and
starts playing the tape.
Eject the cassette
6PUSH OPEN/ CLOSE
POWER
Turn on/ off the player
To select the direction of the tape
Press DIR MODE repeatedly.
To play
Display show s
One side of the tape
Both sides of the tape
from the front side to reverse
side only
Both sides of the tape repeatedly
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Re co rd in g o n a t a p e
3
1
Connect the supplied AC power cord (see page 34.)
To record on a MiniDisc or DAT recorder, connect the
component (see page 36).
1
2
Press 6PUSH OPEN/ CLOSE to
open the tape compartment, and
insert a blank tape. Use TYPE I
(normal) tape only.
Press 6PUSH OPEN/ CLOSE
again to close the compartment.
With the side you w ant to
record on facing forw ard
Select the program source you
want to record.
Display
To record from the CD player,
insert a CD (see page 4) and press
pon the CD section.
To record from the radio, press
BAND and tune in the station
you want (see page 6).
10 Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording from the CD
player
3
Start recording.
Press r/ Pand then (.
To record on the reverse side,
press 9. (On the remote, while
keeping r/ Ppressed, press
TAPE (or 9.)
To record from the CD player,
press ^to start playing the CD
tracks. (On the remote, press (
on the CD section.)
Recording from the
radio
Note
On the player, press (within 4
seconds after r/ Pis pressed.
Tips
Use these buttons for additional operations
•
Adjusting the volume or
the audio emphasis (see
page 39) will not affect
the recording level.
POWER r/P
MODE•MONO/ST ISS
p
•
When
or
is
displayed, recording will
be made on both sides of
the tape. To record on
one side, press DIR
MODE to display
.
•
If the AM radio makes a
whistling sound after
you’ve pressed
DIR MODE
r/ Pin step 3, press
MODE• MONO/ ST ISS
to select the position that
most decreases the noise.
To
Press
Stop recording
Pause recording
p
r/P
Press the button again to
resume recording.
Turn on/ off the player
POWER
To erase a recording, proceed as follows:
1 Insert a tape you want to erase its recording into tape deck
and press pon the tape section.
2 On the player: press r/ Pand then (.
On the remote: While keeping r/ Ppressed, press (on the
tape section.
Basic Operations 11
Download from Www.Somanuals.com. All Manuals Search And Download.
The CD Player
Usin g t h e d isp la y
DISPLAY ENTER MEMORY
You can check information about the CD
using the display.
Checking the total track number and playing
time
Press DISPLAY ENTER MEMORY in stop mode.
Total track number
Total playing time
Checking the remaining time
Press DISPLAY ENTER MEMORY while playing a
CD.
To display
Press DISPLAY ENTER
MEMORY
The current track number
and the remaining time
on the current track*
Once
Remaining time on the CD
and the number of tracks left
Twice
The current track number
and playing time
Three times
* For a track whose number is more than 20 the remaining
time appears as “– –:– –”.
12 The CD Player
Download from Www.Somanuals.com. All Manuals Search And Download.
Lo ca t in g a sp e cific
t ra ck
You can quickly locate any track using
the number buttons. You can also find a
specific point in a track while playing a
CD.
Number
buttons
=, +
Note
You cannot locate a
specific track if
“SHUF” or “PGM” is lit
in the display. Turn off
the indication by
pressing pon the CD
section.
To locate
Press
A specific track directly
Number button of the
track.
A point while listening to
the sound
=or +while playing
and hold down until you
find the point.
A point while observing
the display
=or +in pause and
hold down until you find
the point.
Tip
When you locate a
track numbered over
10, press >10 first, then
the corresponding
number buttons.
Example:
To play track number
23, press >10 first, then
2 and 3.
The CD Player 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g t ra cks
re p e a t e d ly
(Re p e a t Pla y)
Number
buttons
You can play tracks repeatedly in
normal, shuffle or program play modes
(see pages 16 - 18).
MODE
(
p
Note
1 Press pon the CD section.
When you repeat a
single track or all the
tracks, make sure
neither “SHUF” nor
“PGM” is lit in the
display. If either is lit,
turn it off by pressing
pon the CD section.
“Cd” appears in the display.
2 Proceed as follows.
To repeat
Do this
A single track
1 Press MODE until “REP 1”
appears.
2 Press the number buttons
to select the track that you
want to repeat.
On the player
•
Use MODE• MONO/
ST ISS to select “REP
1”, “REP ALL”, “REP”
“SHUF” or “REP”
“PGM”.
All the tracks
1 Press MODE until “REP
ALL” appears.
2 Press (on the CD
section.
•
Use =or +to
select the track that you
want, and then press
^.
Tracks in random order
Programmed tracks
1 Press MODE until “REP”
“SHUF” appears.
2 Press (on the CD
section.
1 Start program play. (See
pages 17 and 18.)
2 Press MODE until “REP”
“PGM” appears.
3 Press (on the CD
section.
To cancel Repeat Play
Press MODE until “REP” disappears from the display.
14 The CD Player
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g a sin g le
t ra ck
(Sin g le Tra ck Pla y)
Number
buttons
You can play a single track once, and
stop the player automatically.
MODE
(
p
1 Press pon the CD section.
“Cd” appears in the display.
On the player
2 Press MODE until “1TRACK” appears in the
•
Use MODE• MONO/
ST ISS to select
“1TRACK”.
display.
3 Press the number buttons to select the track you
•
Use =or +to
select the track that you
want, and then press
^.
want to play.
To cancel Single Track Play
Press MODE until “1TRACK” disappears from the
display.
The CD Player 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g t ra cks in
ra n d o m o rd e r
(Sh u ffle Pla y)
You can play tracks in random order.
MODE
(
p
1 Press pon the CD section.
“Cd” appears in the display.
On the player
2 Press MODE until “SHUF” appears in the display.
Use MODE• MONO/
ST ISS to select
“SHUF”.
3 Press (on the CD section to start shuffle play.
To cancel Shuffle Play
Press MODE until “SHUF” disappears from the
display.
16 The CD Player
Download from Www.Somanuals.com. All Manuals Search And Download.
Cre a t in g yo u r
o w n p ro g ra m
(Pro g ra m Pla y)
^
PROGRAM•AUTO PRESET
CHECK
While listening to the CD, you can
select the track you want and arrange
the playing order of up to 20 tracks on
a CD.
p
DISPLAY
ENTER
MEMORY
=, +
1 Press ^to start play.
2 Press PROGRAM• AUTO PRESET• CHECK until
“PGM” appears in the display.
Tips
3 Press =or +to select the track you want to
program, and press DISPLAY ENTER MEMORY.
Repeat this step.
•
If you made a mistake,
press CANCEL and re-
enter the track number
by pressing =or
+and press
DISPLAY ENTER
MEMORY.
Total programmed time
(displayed for about 2 seconds)
•
You can also create a
program in stop mode.
Note
When you program a
track from the CD
having more than 20
tracks:
If you program a track
whose track number is
more than 20, “- -:- -” is
displayed instead of the
total programmed time.
Playing order
Track number
4 Press pon the CD section.
5 Press ^to start program play.
continued
The CD Player 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cre a t in g yo u r o w n p ro g ra m (Pro g ra m Pla y) (continued)
Tips
To cancel Program Play
Press MODE• MONO/ ST ISS until “PGM” disappears
from the display.
•
If the program play is
finished, the program is
saved. You can play the
same program again by
pressing ^.
To check the order of tracks before play
Press PROGRAM• AUTO PRESET• CHECK in stop
mode until “CHECK” appears in the display.
•
•
If you open the CD
compartment, the
program is erased.
You can record your
own program.
As you press =or +, the track number appears
in the programmed order.
1 After you’ve created
the program, insert a
blank tape into the
tape compartment.
To change the current program
2 Press r/ Pand then
(to start recording.
Press ^to start
playing the program
play.
Change before starting the program play.
To
Do this
Erase the last track in
the program
1 Press CANCEL. Every time
you press the button, the last
track in the program is
cleared.
2 Re-enter the track numbers
using =or +and
DISPLAY ENTER MEMORY.
Change the whole
program completely
1 Press pon the CD section to
erase the whole program.
2 Create a new program
following the programming
procedure.
18 The CD Player
Download from Www.Somanuals.com. All Manuals Search And Download.
The Radio
Pre se t t in g ra d io
st a t io n s
BAND PROGRAM•AUTO PRESET
CHECK
You can store radio stations into the
player's memory. You can preset up to
20 radio stations, 10 for FM and AM in
any order.
1 Press BAND until the band you want appears in
the display.
2 Hold down PROGRAM• AUTO PRESET• CHECK
until “AUTO” appears in the display.
The stations are stored in memory from the lower
frequencies unless a station has a weak signal.
If a station cannot be preset automatically
You need to preset a station with a weak signal
manually. Also, when you want to replace a preset
station with a new one, proceed as follows:
On the player
On the remote:
1 Press BAND to tune in
the band you want.
2 Hold down DISPLAY
ENTER MEMORY for
about 2 seconds.
1 Press BAND until the band you want appears in the
display.
2 Press TUNE/ TIME SET + or – until you tune in a
station you want.
3 Press PRESET + or – to
display the preset
3 Hold down the number buttons that you want to
number you want.
preset the new station for about 2 seconds.
4 Press DISPLAY ENTER
MEMORY.
The new station replaces the old one.
5 Press TUNE/ TIME SET
+ or – to tune in a
station you want.
6 Press DISPLAY ENTER
MEMORY.
The Radio 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g p re se t
ra d io st a t io n s
Once you've preset the stations, use the
number buttons on the remote or
PRESET +/ – on the player to tune in
your favorite stations.
Number
buttons
BAND
On the player
1 Press BAND to tune in the band you want.
Use PRESET + or – to
display the preset
number you want.
2 Press the number buttons to display the preset
number of the station you want.
Preset number
20 The Radio
Download from Www.Somanuals.com. All Manuals Search And Download.
The Tape Player
Fin d in g
t h e b e g in n in g o f
a t ra ck
The player detects a blank between the
tracks, and locates the beginning of the
next/ following track.
0, )
Notes
While playing a tape, press )or 0.
•
If a soft sound like
pianissimo continues
for some seconds in a
track, the player may
start to play as the next
track.
Playing side
The beginning
The beginning
of the current
track
of the next track
Front side (()
)
0
0
)
Reverse side (9)
•
•
If you press the )or
0when there is no
sound in the track, this
function does not
The tape is wound or rewound to the beginning of the
next or current track, and play will start automatically.
operate correctly.
To find the beginning
of a track correctly,
a blank of approx. 4
seconds is necessary.
The Tape Player 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g t h e
t ra cks o n CD b y
sp e cifyin g t h e
t a p e le n g t h
r/P p
EDIT
DISPLAY ENTER
MEMORY
There are three options in editorial
recording:
=, +
• Recording all the tracks in the original
CD order. (EDIT ALL)
• Recording programed tracks (EDIT
PGM)
6PUSH
OPEN/CLOSE
(
• Recording a single track you have
selected (EDIT 1TRACK)
Tips
Recording all the tracks on CD (EDIT ALL)
Approximately the first half of the CD will be
recorded on one side of the tape, and the second half
will be recorded on the other side, without reversing
the tape in the middle of a track. According to the tape
you use, you can set the total recording time.
•
You can edit a CD
having 20 tracks or
fewer.
•
We recommend that
you use AC power as
the power source for
optimum recording
quality.
1 Press pon the CD section until “Cd” appears in
Note
Do not open the CD
compartment while
editing; the settings for
recording will be
the display.
2 Press EDIT to display “E-ALL”.
erased. If you do, start
from step 1 again.
.
The tape length (unit: 2
minutes, up to 98 minutes)
you need to record the
whole CD appears in the
display.
Example: The total tape length needed to record
the entire CD is “26” minutes. The maximum
recording time for each side is 13 minutes.
Track Nos.: 1
2
3
4
5
6
7
Length:
(minutes)
01:20 02:30 03:40 04:50 05:10 04:20 01:30
Side A (12:20) Side B (11:00)
22 The Tape Player
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
To check the total
recording time on the
front side and the
3 To change the recording time, press =or +.
If you do not change the recording time, skip to
step 5.
reverse side:
Press DISPLAY ENTER
MEMORY before
starting recording. Each
time you press the
button, the display
changes as follows:
“total recording time
on the front side” n
“total recording time
on the reverse side” n
“the total track number
and the tape length you
need to record the
whole CD.”
Example: If you input “40” minutes for the
recording time, the maximum recording time for
each side is 20 minutes.
Track Nos.: 1
2
3
4
5
6
7
Length:
(minutes)
01:20 02:30 03:40 04:50 05:10 04:20 01:30
Side A (17:30) Side B (5:40)
4 Press DISPLAY ENTER MEMORY.
5 Insert a blank tape into the tape compartment.
6 Press r/Pand then (.
Recording will start on the front side
automatically.
The Tape Player 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g t h e t ra cks o n CD b y sp e cifyin g t h e t a p e le n g t h
(continued)
r/P p
EDIT
DISPLAY ENTER
MEMORY
=, +
6PUSH
OPEN/CLOSE
(
Recording programed tracks (EDIT PGM)
Note
Do not open the CD
compartment while
editing; the settings for
recording will be erased.
If you do, start from step
1 again.
The first half of the programed tracks will be recorded
on one side of the tape, and the second half will be
recorded on the other side. According to the tape you
use, you can set the total recording time.
1 Press pon the CD section until “Cd” appears in
the display.
2 Press EDIT to display “E-PGM”.
.
24 The Tape Player
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
When “--” is displayed
3 Press =or +to select the track you want to
program, and press DISPLAY ENTER MEMORY.
as the tape length, the
total recording time of
the programed tracks
exceeds 98 minutes.
Start from step 1 again.
The total number of programed tracks and the
minimum tape length (unit: 2 minutes, up to 98
minutes) you need to record the programed tracks
appear in the display.
4 Repeat step 3.
Tips
•
If you made a mistake,
press CANCEL. The
track programed last
will be cleared. Re-
program it.
5 To change the recording time, press DISPLAY
ENTER MEMORY.
If you do not change the recording time, skip to
step 7.
•
To check the order of
tracks, press
Tape length flashes.
PROGRAM• AUTO
PRESET• CHECK in
stop mode until
“CHECK” appears in
the display. Press
=or +to display
the track number in the
programmed order.
6 Press =or +to change the recording time
and press DISPLAY ENTER MEMORY.
•
To check the total
recording time on the
front side and the
reverse side:
Press DISPLAY
ENTER MEMORY
before starting
recording. Each time
you press the button,
the display changes as
follows: “total
7 Insert a blank tape into the tape compartment.
8 Press r/Pand then (.
Recording will start on the front side automatically.
The tracks are recorded in the programed order.
recording time on the
front side”
recording time on the
reverse side” “total
n
“total
n
track number and the
tape length you need
to record the whole
CD.
The Tape Player 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g t h e t ra cks o n CD b y sp e cifyin g t h e t a p e le n g t h
(continued)
r/P p
EDIT
DISPLAY ENTER
MEMORY
=, +
6PUSH
OPEN/CLOSE
(
Recording a single track (EDIT 1TRACK)
EDIT 1TRACK is useful to record the first track of
single CD, and to record a track from a number of
different CDs. Recorded on the both sides mode
“
” is automatically selected.
1 Insert a blank tape into the tape compartment.
2 Press pon the CD section until “Cd” appears in
the display.
3 Press EDIT to display “E-1”.
.
26 The Tape Player
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press =or +to select the track you want to
program.
5 Press r/Pand press TAPE(to record on the
front side or TAPE9to record on the reverse side.
Recording will start for the selected track.
When recording of the track is finished, the CD
player and the cassette deck stop. The total number
of tracks recorded and the total recording time
appear in the display.
When you record another track, repeat steps 4 and
5, or change the source CD and repeat steps 4 and
5.
The Tape Player 27
Download from Www.Somanuals.com. All Manuals Search And Download.
The Timer
Se t t in g t h e clo ck
CLOCK
DISPLAY ENTER
MEMORY
“--:--” indication appears in the display
until you set the clock.
=, +
Tips
Before you begin, connect to the power source (see
pages 34 - 35).
•
The time display
system of this player is
the 12-hour system.
•
When you use the AC
power cord, “:” flashes
as long as the clock
goes.
1 Press and hold CLOCK until the hour digit flashes.
2 Set the clock.
1 Press =or +to set
the hour and press
DISPLAY ENTER
MEMORY.
.
2 Press =or +to set
the minutes.
3 Press DISPLAY ENTER MEMORY.
The clock starts from 00 seconds.
28 The Timer
Download from Www.Somanuals.com. All Manuals Search And Download.
Wa kin g u p t o
m u sic
TIMER STANDBY
DISPLAY ENTER
MEMORY
You can wake up to music or a radio
program at a preset time. Make sure you
have set the clock (“Setting the clock” on
page 28).
=, +
Before you begin, make sure the t(clock) indication is
not lit in the display. If it is lit, press STANDBY.
1 Prepare the music source you want to play.
Source
Do this
Cd
Insert a CD.
Tune in a station.
Insert a tape.
RAdIO
TAPE
LINE
Turn on the equipment connected to
LINE.
2 Press TIMER to display the tindication.
Do the following operations by checking the
display.
3 Press =or +until the music source you want
to play (“Cd”, “TAPE”, “RAdIO” or “LINE”)
appears in the display, and press DISPLAY ENTER
MEMORY.
continued
The Timer 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Wa kin g u p t o m u sic (continued)
Tip
4 Set the timer to the hour and the minutes you
If you made a mistake,
press CANCEL. The
setting entered last will
be cleared. Re-enter it.
want the music to go on.
1 Press =or +
to set the hour and
press DISPLAY
ENTER MEMORY.
2 Press =or +to set the minutes, and press
DISPLAY ENTER MEMORY.
5 Set the timer to the hour and the minutes you
want the music to go off. (Do as step 4.)
6 Press =or +to set the volume you want, and
press DISPLAY ENTER MEMORY.
Tips
7 Press STANDBY.
•
To exit the standby
mode, press STANDBY
to make the t
The tindication lights up and the power goes off;
the player enters the standby mode.
indication disappear.
At the preset time, the power will go on and music
will play. Then the power will go off at the preset
time, and the player will enter the standby mode
again.
•
•
The preset settings
remain until you reset
them.
The display window
does not light while the
waking up timer is on.
To check/change the w aking up timer settings
Press TIMER, then DISPLAY ENTER MEMORY. Each
time you press DISPLAY ENTER MEMORY, a stored
setting is displayed in the set order. To change the
setting, display the setting you want to change and re-
enter it.
To use the player before a timer playback starts
If you turn on the player, you can use it as usual (in
case of the radio, if you listen to the station which is
different from the one you tuned in step 1 on page 29,
you will hear that station at the preset time). Turn off
the player before the preset time.
To stop play
Turn off the power.
30 The Timer
Download from Www.Somanuals.com. All Manuals Search And Download.
Fa llin g a sle e p t o
m u sic
SLEEP
You can set the player to turn off
automatically after 10, 20, 30, 60, 90 and
120 minutes, allowing you to fall asleep
while listening to music.
Tips
1 Play the music source you want.
2 Press SLEEP to display “SLEEP.”
•
The display window
does not light while the
sleeping timer is on.
3 Press SLEEP to select the minutes when the player
•
You can combine the
waking up timer with
the sleeping timer. Set
the waking up timer
first (see page 29), turn
on the power, and then
set the sleeping timer.
goes off automatically.
Each time you press
the button, the
indication changes as
follows: “10” n “20”
n “30” n “60” n
“90” n “120” n
no indication.
•
•
You can prepare the
different music for the
waking up timer and
the sleeping timer.
However, you cannot,
store different radio
stations.
You can set different
volume for the waking
up timer and the
If 4 seconds have passed after you pressed SLEEP,
the minutes in the display are stored in memory.
When the preset time has passed, music stops and
the player goes off automatically.
sleeping timer. For
instance, you can sleep
at lower volume and
wake up at higher
volume.
To cancel the sleep function
Press SLEEP to make “SLEEP” disappear from the
display.
To change the preset time
Do the steps 2 and 3 again.
The Timer 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Tim e r-re co rd in g
ra d io p ro g ra m s
TIMER STANDBY
DISPLAY ENTER
MEMORY
You can set timer to record the radio at a
certain time. You can also record the
sound of the component connected to
the LINE IN jack, using the timer. Make
sure you have set the clock (see “Setting
the clock” on page 28).
=, +
DIR MODE
Note
You cannot preset
recording timer and
waking up timer (page
29) at the same time.
Before you begin, make sure the t(clock) indication
is not lit in the display. If it is lit, press STANDBY.
1 Tune in the radio station and insert a blank tape
into the tape compartment with the side you want
to record on facing forward.
Tips
•
We recommend that
you use AC power as
the power source for
optimum recording
quality.
2 Press DIR MODE to
display
select recording
One side
direction of the tape.
Both sides
•
When you receive the
AM program in step 1,
press r/ Pto check if
the noise is heard. If so,
press MODE• MONO/
ST ISS to select the
3 Press TIMER to display the tindication.
Do the following operations by checking the
display window.
position that most
decreases the noise.
4 Press =or +to display “RAdIO” “REC,”
and press DISPLAY ENTER MEMORY.
32 The Timer
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
If you made a mistake,
press CANCEL. The
setting entered last will
be cleared. Re-enter it.
5 Set the timer to the hour and the minutes you want
to start recording.
1 Press =or +
to set the hour and
press DISPLAY
ENTER MEMORY.
2 Press =or +to set the minutes, and press
DISPLAY ENTER MEMORY.
6 Set the timer to the hour and the minutes you want
to stop recording. (Do as step 5.)
7 Press =or +to set the volume you want, and
press DISPLAY ENTER MEMORY.
Tips
8 Press STANDBY.
•
To exit the standby
The power goes off and the player enters the
standby mode. The tindication and the recording
side of the tape (front side (or reverse side 9)
appear in the display. To change the recording
side, press STANDBY again.
mode, press STANDBY
twice to make the t
indication disappear.
The preset settings
remain until you reset
them.
When you select both
sides recording, the
recording will stop
after the both sides
recording finishes so
that accidental
•
•
At the preset time, the power will go on and the
recording will start. Then the power will go off at
the preset time, and the player will enter the
standby mode again.
recording will not be
made.
To check/change the recording timer settings
Press TIMER, then DISPLAY ENTER MEMORY. Each
time you press DISPLAY ENTER MEMORY, a stored
setting is displayed in the set order. To change the
setting, display the setting you want to change and re-
enter it.
•
The display window
does not light while the
recording timer is on.
To use the player before a timer-recording starts
If you turn on the player, you can use it as usual.
Before the preset time, tune in the station you want to
record and turn off the power.
To stop timer-recording
Turn off the power.
The Timer 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
Ch o o sin g t h e
AC IN
p o w e r so u rce s
You can use the AC power or
batteries as a power source.
Use the AC power source
whenever you record since
recording consumes much
power.
2
14
Battery compartment
To a w all outlet
Note
1 Inserting the back-up batteries
Be sure to turn off the
power of the player
before connecting/
disconnecting the AC
power cord or
Insert four size AA (R6) batteries (not supplied) into
the battery compartment. These batteries work to save
the memory data.
removing/ inserting
batteries.
Insert four size AA (R6) batteries (not supplied)
Replacing batteries
With normal use, the back-up batteries should last for
about six months when the player is operated on
batteries. When the time display dims or when the
timer function is disabled, replace all the batteries
with new ones. To save the preset settings, replace the
batteries with the AC power cord connected.
Tip
2 Connecting the AC pow er cord
The sound quality may
be changed depending
on the polarity of the
plug. Change the
Insert one end of the supplied AC power cord to the
AC IN socket located at the rear of the player, and the
other end to the wall outlet.
direction of inserting
the plug and check the
sound quality.
34 Setting Up
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Inserting batteries into the remote
Insert tw o size AA (R6) batteries (not supplied)
Replacing batteries
With normal use, the batteries should last for about six
months. When the remote no longer operates the
player, replace all the batteries with new ones.
Notes
4 Using the player on batteries
Insert eight size D (R20) batteries (not supplied) into
the battery compartment.
•
When you insert or
remove the batteries,
disconnect the
connecting cords and
cables to prevent
damaging them.
To use the player on batteries, disconnect the AC
power cord from the player.
•
•
When you operate the
player on batteries, the
backlight in the display
does not light.
When you operate the
player on batteries, you
can't turn on the player
using the remote.
Insert eight size D (R20) batteries (not supplied)
Replacing batteries
When the OPR/ BATT indicator dims or when the
player stops operating, replace all the batteries with
new ones.
Setting Up 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n n e ct in g
o p t io n a l
MD (LINE)
co m p o n e n t s
You can record a CD on a MiniDisc or
enjoy the sound from a VCR, TV or
MiniDisc player/ recorder through the
speakers of this player.
Be sure to turn off the power of each
component before making connections.
For details, refer to the instruction
manual of the component to be
connected.
Note
Recording a CD on a MiniDisc recorder and
DAT recorder
Connect the cables
firmly to avoid any
malfunction.
Front panel of
this player
MiniDisc
recorder, DAT
recorder, etc.
To digital input
jack
Digital Connecting
cable* POC-5AB
(not supplied)
To OPTICAL
DIGITAL OUT
(CD) jack
* Select a connecting cable depending on the type of the
digital input jack of the recorder to be connected. For
details, refer to the instruction manual of the component to
be connected. The OPTICAL DIGITAL OUT (CD) jack of
this unit is square-shaped jack.
The type of the jack
of the component
to be connected
Model number of
the connecting cable
Optical miniplug
(MiniDisc recorder, etc.)
POC-5AB
POC-DA12P
POC-10A
L-type 7-pin connector
(DAT recorder, etc.)
Square-shaped optical
connector (MiniDisc
recorder, DAT recorder, etc.)
36 Setting Up
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
To record a track from
a number of different
CDs, EDIT 1TRACK is
useful (page 26).
1 Connect the OPTICAL DIGITAL OUT (CD) jack of
this player with the digital input jack of the
MiniDisc recorder or other component using the
digital connecting cable (not supplied) .
1 Make connections.
2 Turn on the power of this player and the connected
2 Turn on this player
and the connected
component.
3 Do steps 2 through 5
on pages 26 and 27.
4 Make the connected
component ready for
recording.
5 Start playing a CD on
this player.
component.
3 Make the connected component ready for
recording.
4 Start playing a CD on this player.
Listening to TV, VCR and MiniDisc player/
recorder
Front panel of this
player
TV, VCR, MiniDisc
player/recorder,
etc.
To LINE IN jack
Audio connecting cable
For portable MiniDisc
player/recorder:
RK-G136HG (1.5 m)
(not supplied)
To line output
jack
For TV or VCR:
RK-G129HG (1.5 m)
(not supplied)
Tip
1 Connect the LINE IN jack of this player with the
line output jack of the MiniDisc player or other
component using the audio connecting cable (not
supplied) .
You can record the
sound of the connected
component. Insert a
blank tape into the tape
compartment, and
press r/ Pthen
2 Turn on the power of this player and the connected
component.
TAPE((page 11).
3 Press MD (LINE) and start playing sound on the
connected component.
The sound from the connected component is
output from the speakers.
continued
Setting Up 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n n e ct in g o p t io n a l co m p o n e n t s (continued)
Notes
Listening through the speakers of other audio
equipment
•
As long as “Cd”
appears in the display,
the optical digital
output jack is in
Front panel of this
player
operation and the jack
lights even if the CD is
in stop mode.
Amplifier
•
If you play a CD-ROM
that is not for audio
use, noise may be
heard.
Audio connecting
cable RK-G129HG
(1.5 m) (not supplied)
To LINE OUT
jack
To analog line
input jack
1 Connect the LINE OUT jack of this player with the
analog line input jack of the amplifier using the
audio connecting cable (not supplied) .
2 Turn on the power of this player and the amplifier
and start playing sound on this player.
38 Setting Up
Download from Www.Somanuals.com. All Manuals Search And Download.
Se le ct in g t h e
MEGA BASS SOUND
a u d io e m p h a sis
(So u n d Mo d e /MEGA BASS)
You can adjust the audio emphasis of the
sound you are listening to.
Selecting the sound characteristic
Press SOUND to select the audio emphasis you want.
Each time the button is pressed, the display changes.
Choose
To get
For rock’n’roll music:
powerful, clean sounds, emphasizing
low and high range audio.
For popular music:
light, bright sounds emphasizing
high and middle range audio.
For jazz:
percussive sounds, emphasizing bass
audio.
For vocals:
the presence of vocals, stressing
middle range audio.
For classical music:
the whole dynamic range for music.
Reinforcing the bass sound
Press MEGA BASS.
“MEGA BASS” appears in the display. To return to
normal sound, press the button again.
Setting Up 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Pre ca u t io n s
On safety
On placement
• As the laser beam used in the CD
player section is harmful to the eyes,
do not attempt to disassemble the
casing. Refer servicing to qualified
personnel only.
• Do not leave the player in a location
near heat sources, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
• Do not place the player on an inclined
or unstable place.
• Should any solid object or liquid fall
into the player, unplug the player, and
have it checked by qualified personnel
before operating it any further.
• Do not place anything within 10 mm
of the side of the cabinet. The
ventilation holes must be
unobstructed for the player to operate
properly and prolong the life of its
components.
On pow er sources
• For AC operation use the supplied AC
power cord; do not use any other type.
• If the player is left in a car parked in
the sun, be sure to choose a location in
the car where the player will not be
subjected to the direct rays of the sun.
• The player is not disconnected from
the AC power source (mains) as long
as it is connected to the wall outlet,
even if the player itself has been
turned off.
• Since a strong magnet is used for the
speakers, keep personal credit cards
using magnetic coding or spring-
wound watches away from the player
to prevent possible damage from the
magnet.
• Unplug the player from the wall outlet
when it is not to be used for an
extended period of time.
• For battery operation, use eight size D
(R20) batteries.
On operation
• When the batteries are not to be used,
remove them to avoid damage that
can be caused by battery leakage or
corrosion.
• If the player is brought directly from a
cold to a warm location, or is placed in
a very damp room, moisture may
condense on the lenses inside the CD
player section. Should this occur, the
player will not operate properly. In
this case, remove the CD and wait
about an hour for the moisture to
evaporate.
• The nameplate indicating operating
voltage, power consumption, etc. is
located at the bottom.
• If the player has not been used for a
long time, set it in the playback mode
to warm it up for a few minutes before
inserting a cassette.
If you have any questions or problems
concerning your player, please consult
your nearest Sony dealer.
40 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on CDs
Notes on cassettes
• Before playing, clean the CD with a
cleaning cloth. Wipe the CD from the
center out.
• Break off the cassette tab from side A
or B to prevent accidental recording. If
you want to reuse the tape for
recording, cover the broken tab with
adhesive tape.
Side A
• Do not use solvents such as benzine,
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
Tab for side B
Tab for side A
• Take care not to cover the detector
slots on TYPE II (high position) or
TYPE IV (metal) cassettes. If the slots
are covered, the automatic tape
selection system will not operate
correctly.
• Do not expose the CD to direct
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature
inside the car.
• Do not stick paper or sticker on the
CD, nor scratch the surface of the CD.
• After playing, store the CD in its case.
If there is a scratch, dirt or fingerprints
on the CD, it may cause tracking error.
TYPE II (high
position)
TYPE IV (metal)
detector slots
detector slots
• The use of a cassette with more than
90 minutes of play time is not
recommended except for long,
continuous recording or playback.
Additional Information 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g
Symptom
Remedy
There is no audio.
•
•
Press POWER to turn on the player.
Connect the AC power cord to the AC IN socket
and a wall outlet securely.
•
•
Make sure the batteries are inserted correctly.
Replace all the batteries with new ones if they
are weak.
•
•
Adjust the volume.
Unplug the headphones when listening through
speakers.
The power is turned off
automatically.
•
•
Replace all the batteries with new ones.
Unusual sound is heard.
The sound is noisy, weak or has
poor quality.
Replace all the batteries with new ones if they
are weak.
Noise is heard.
•
Someone is using a portable telephone or other
equipment that emits radio waves near the
player. n Move the portable telephone, etc.,
away from the player.
The CD does not play.
•
•
•
•
Make sure that the CD compartment is closed.
Place the CD with the label surface up.
Clean the CD.
“NO DISC“ lights in the display
even when a CD is in place.
Take out the CD and leave the CD compartment
open for about an hour to dry moisture
condensation.
•
Press pon the CD section to switch the function
of the player to “Cd”.
The sound drops out.
•
•
Reduce the volume.
Clean the CD, or replace it if the CD is badly
damaged
•
•
Place the player in a location free from
vibration.
When listening to the CD, the TV or
radio becomes noisy.
Move the player away from the TV or radio.
42 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The audio is not stereo.
• Press MODE• MONO/ ST ISS until “STEREO”
appears.
The audio is weak or has poor
quality.
• Depending on the FM reception conditions,
noise may be heard.
• Replace all the batteries with new ones if they
are weak.
• Move the player away from the TV.
• If you are using the remote while listening to
AM radio, noise may be heard. This is
unavoidable.
The picture of your TV becomes
unstable.
• If you are listening to an FM program near the
TV with an indoor antenna, move the player
away from the TV.
The tape does not move when you
press an operation button.
• Insert the tape properly and close the tape
compartment securely.
• Replace all the batteries with new ones.
The r/ Pbutton does not function/ • Make sure the safety tab of the tape in the tape
The tape does not play.
compartment is in place.
• Press pon the TAPE section to switch the
function of the player to “TAPE”.
The tape does not erase completely. • Clean the erasing heads (see page 45).
• The source which was recorded on TYPE II
(high position) or TYPE IV (metal) tape using
this unit is being played. Record on TYPE I
(normal) tape and play.
The tape does not record.
• Make sure the tape is inserted properly.
• Make sure the safety tab of the tape in the tape
compartment is in place.
The audio is weak/ The audio
quality is poor.
• Clean the heads, pinch rollers and capstans (See
page 45).
• Demagnetize the heads using a demagnetizer
(see page 45).
The tape player cannot be paused
during playback.
• The tape player can be paused during recording
only.
The sound is distorted.
• The source which was recorded on TYPE IV
(metal) tape using this unit is being played.
n Record on TYPE I (normal) or TYPE II (high
position) tape and play.
continued
Additional Information 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g (continued)
Symptom
Remedy
The timer does not operate.
•
•
Make sure the time on the clock is correct.
Replace all the batteries in the player including
the back-up batteries with new ones if they are
weak.
•
•
•
•
Check to see if the AC power had been cut off.
Make sure the tape has not wound to the end.
Make sure the t(clock) indication is displayed.
The remote does not function.
Replace all the batteries in the remote with new
ones if they are weak.
•
•
•
Make sure that you are pointing the remote at
the remote sensor on the player.
Remove any obstacles in the path of the remote
and the player.
Make sure the remote sensor is not exposed to
strong light such as direct sunlight or
fluorescent lamp light.
•
Move closer to the player when using the
remote.
The player uses a built-in micro computer for its various operations. Due to change in power
supply conditions, etc., operation may sometimes become unstable. After trying the above
remedies, if the player still does not function properly, unplug the AC power cord and remove
all the batteries. After all indications in the display disappear, plug the AC power cord and
insert the batteries again. If the problem persists, please consult your nearest Sony dealer.
44 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma in t e n a n ce
Cleaning the tape heads and tape
path
Demagnetizing the tape heads
After 20 to 30 hours of use, enough
residual magnetism will have built up
on the tape heads to begin to cause loss
of high frequency sound and hiss. At
this time, you should demagnetize the
heads and all metal parts in the tape
path with a commercially available tape
head demagnetizer.
Wipe the heads, the pinch rollers and
the capstans with a cleaning swab
slightly moistened with cleaning fluid or
alcohol after every 10 hours of operation
for optimum playback and recording
quality. To make the best possible
recording, however, we recommend that
you clean all surfaces over which tape
travels before each recording.
Cleaning the lens
If the lens becomes dirty, it may cause a
skipping of sound during CD operation.
Clean with a commercially available
blower.
Capstan
Record/Playback
head
Cleaning the cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder, or solvent, such as alcohol or
benzine.
Erase head
Pinch roller
Lens
After cleaning, insert a tape when the
areas cleaned are completely dry.
Additional Information 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Sp e cifica t io n s
AUDIO POWER SPECIFICATIONS
General
Speaker
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
Full range: 8 cm (3 1⁄4 in.) dia., 3 ohms,
cone type x 2
With 3-ohm loads, both channel driven from
150 - 15,000 Hz; rated 3 W per channel-
minimum RMS power, with no more than
10 % total harmonic distortion in AC
operation.
Input
LINE IN jack (stereo minijack)
Minimum input level 250 mV
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones
LINE OUT jack (stereo minijack)
Rated output level 250 mV at load impedance
47 kilohms
Other Specifications
CD player section
OPTICAL DIGITAL OUT (CD) (optical output
connector)
System
Compact disc digital audio system
Laser diode properties
Wavelength: 630 - 690 nm
Power output (excluding U.S. model)
Material: GaAlAs
Wave length: 780 nm
4.5 W + 4.5 W (3 ohms at 10 % harmonic
distortion in DC operation)
Emission duration: Continuous
Power requirements
Laser output: Less than 44.6 µW (This output is the
value measured at a distance of about 200 mm from
the objective lens surface on the optical pick-up
block with 7 mm aperture.)
For Personal Audio System:
120 V AC, 60 Hz
12 V DC, 8 size D (R20 ) batteries
Spindle speed
For memory back-up:
200 r/ min (rpm) to 500 r/ min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +0/ –1 dB
Wow and flutter
6 V DC, 4 size AA (R6) batteries
For remote commander:
3 V DC, 2 size AA (R6) batteries
Power consumption
AC 25 W
Battery life
Below measurable limit
For Personal Audio System:
FM recording
Radio section
Frequency range
Sony R20P: approx. 6 h
Sony alkaline LR20: approx. 12 h
Tape playback
FM: 87.6 - 108 MHz
AM: 530 - 1,710 kHz
Aerials
FM: Telescopic aerial
AM: Built-in ferrite bar aerial
Sony R20P: approx. 3 h
Sony alkaline LR20: approx. 6 h
CD playback
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120s (sec.) with Sony cassette C-60
Frequency response
Sony R20P: approx. 1.5 h
Sony alkaline LR20: approx. 3 h
TYPE I (normal): 50 - 15,000 Hz
Dimensions (incl. projecting parts)
Approx. 416 × 198.5 × 246 mm (w/ h/ d)
(16 1⁄2 ×7 7⁄8 × 9 3⁄4 inches)
Mass (incl. batteries)
Approx. 5.2 kg (11 lb. 7 oz)
Supplied accessories
AC power cord (1)
Remote commander (1)
Design and specifications are subject to change without
notice.
Optional accessories
Sony MDR headphone series
46 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x
L
A
R
Listening
Audio emphasis 39
Radio stations
through the speakers of
other audio equi 38
playing 20
B
presetting 19
Recording
Batteries
to the radio 6
for memory 34
for player 35
for remote 35
to the TV, VCR and
MD player 37
a single track 26
all the tracks on CD 22
on a tape 10
Locating
a specific track 13
on an MD or a DAT 36
programed tracks 24
C
the beginning of a track
21
CD Player 12
timer-recording radio
programs 32
Cleaning
M, N, O
MEGA BASS 39
cabinet 45
CD 41
Repeat Play 14
lens 45
P, Q
S
tape heads and path 45
Connecting
AC power cord 34
Playing
Selecting
a CD 4
audio emphasis 39
power sources 34
tracks 5, 13
a single track 15
a tape 8
optional components
36
preset radio stations 20
Setting the clock 28
Setting up 34
Shuffle Play 16
SOUND 39
Creating your own
program 17
tracks in random order
16
tracks repeatedly 14
D
Presetting radio stations
19
Demagnetizing the tape
heads 45
Sound mode 39
Program Play 17
T
Display 12
Tape Player 21
E, F, G, H
Timer
EDIT 1TRACK 26
EDIT ALL 22
EDIT PGM 24
falling asleep to music
31
recording radio
programs 32
I, J, K
Improving broadcast
reception 7
waking up to music 29
Troubleshooting 42
U, W, X, Y, Z
Using the display 12
Additional Information 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|